Dreambox DM800 HD se V2 Bedienungsanleitung

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91

Zur Seite of

Richtige Gebrauchsanleitung

Die Vorschriften verpflichten den Verkäufer zur Übertragung der Gebrauchsanleitung Dreambox DM800 HD se V2 an den Erwerber, zusammen mit der Ware. Eine fehlende Anleitung oder falsche Informationen, die dem Verbraucher übertragen werden, bilden eine Grundlage für eine Reklamation aufgrund Unstimmigkeit des Geräts mit dem Vertrag. Rechtsmäßig lässt man das Anfügen einer Gebrauchsanleitung in anderer Form als Papierform zu, was letztens sehr oft genutzt wird, indem man eine grafische oder elektronische Anleitung von Dreambox DM800 HD se V2, sowie Anleitungsvideos für Nutzer beifügt. Die Bedingung ist, dass ihre Form leserlich und verständlich ist.

Was ist eine Gebrauchsanleitung?

Das Wort kommt vom lateinischen „instructio”, d.h. ordnen. Demnach kann man in der Anleitung Dreambox DM800 HD se V2 die Beschreibung der Etappen der Vorgehensweisen finden. Das Ziel der Anleitung ist die Belehrung, Vereinfachung des Starts, der Nutzung des Geräts oder auch der Ausführung bestimmter Tätigkeiten. Die Anleitung ist eine Sammlung von Informationen über ein Gegenstand/eine Dienstleistung, ein Hinweis.

Leider widmen nicht viele Nutzer ihre Zeit der Gebrauchsanleitung Dreambox DM800 HD se V2. Eine gute Gebrauchsanleitung erlaubt nicht nur eine Reihe zusätzlicher Funktionen des gekauften Geräts kennenzulernen, sondern hilft dabei viele Fehler zu vermeiden.

Was sollte also eine ideale Gebrauchsanleitung beinhalten?

Die Gebrauchsanleitung Dreambox DM800 HD se V2 sollte vor allem folgendes enthalten:
- Informationen über technische Daten des Geräts Dreambox DM800 HD se V2
- Den Namen des Produzenten und das Produktionsjahr des Geräts Dreambox DM800 HD se V2
- Grundsätze der Bedienung, Regulierung und Wartung des Geräts Dreambox DM800 HD se V2
- Sicherheitszeichen und Zertifikate, die die Übereinstimmung mit entsprechenden Normen bestätigen

Warum lesen wir keine Gebrauchsanleitungen?

Der Grund dafür ist die fehlende Zeit und die Sicherheit, was die bestimmten Funktionen der gekauften Geräte angeht. Leider ist das Anschließen und Starten von Dreambox DM800 HD se V2 zu wenig. Eine Anleitung beinhaltet eine Reihe von Hinweisen bezüglich bestimmter Funktionen, Sicherheitsgrundsätze, Wartungsarten (sogar das, welche Mittel man benutzen sollte), eventueller Fehler von Dreambox DM800 HD se V2 und Lösungsarten für Probleme, die während der Nutzung auftreten könnten. Immerhin kann man in der Gebrauchsanleitung die Kontaktnummer zum Service Dreambox finden, wenn die vorgeschlagenen Lösungen nicht wirksam sind. Aktuell erfreuen sich Anleitungen in Form von interessanten Animationen oder Videoanleitungen an Popularität, die den Nutzer besser ansprechen als eine Broschüre. Diese Art von Anleitung gibt garantiert, dass der Nutzer sich das ganze Video anschaut, ohne die spezifizierten und komplizierten technischen Beschreibungen von Dreambox DM800 HD se V2 zu überspringen, wie es bei der Papierform passiert.

Warum sollte man Gebrauchsanleitungen lesen?

In der Gebrauchsanleitung finden wir vor allem die Antwort über den Bau sowie die Möglichkeiten des Geräts Dreambox DM800 HD se V2, über die Nutzung bestimmter Accessoires und eine Reihe von Informationen, die erlauben, jegliche Funktionen und Bequemlichkeiten zu nutzen.

Nach dem gelungenen Kauf des Geräts, sollte man einige Zeit für das Kennenlernen jedes Teils der Anleitung von Dreambox DM800 HD se V2 widmen. Aktuell sind sie genau vorbereitet oder übersetzt, damit sie nicht nur verständlich für die Nutzer sind, aber auch ihre grundliegende Hilfs-Informations-Funktion erfüllen.

Inhaltsverzeichnis der Gebrauchsanleitungen

  • Seite 1

    dr e am b ox DM800 HD se User Manual Digital satellite receiver for free and encrypted Digital Video Broadcasting (D VB) with optional digital reco rd- ing capabilit y . HDTV HDMI-Interface D VB-S2 T uner plugable Ethernet-P o rt 10/100 Mbit internal SA T A ha rddisk connecto r eSA T A-interface colo red OLED displa y Linux OS[...]

  • Seite 2

    F o rew o rd Dear customer, Congratulations on y our new Dream b o x DM800 HD se. This man ual should assist y ou to connect y our dreambox, learning the basic op eration and getting to kno w the additional m ultiple features. Please note that the range of functions expands continiously b y new softw are up dates. If you up dated the soft w are of [...]

  • Seite 3

    Contents 1 Befo re initial op eration of the receiver 1 1.1 Safet y instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1.2 P ac kaging con ten ts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1.3 Views . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [...]

  • Seite 4

    4.7 P aren tal con trol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 5 Ha rd disk op eration 33 5.1 Installation-Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 5.2 Managemen t . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [...]

  • Seite 5

    9 Up dating the soft w a re 66 9.1 Bac king up y our settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 9.2 Restoring y our settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 9.3 Up dating a new softw are . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[...]

  • Seite 6

    Chapter 1 Befo re initial op eration of the receiver 1.1 Safet y instructions Please read the safety instructions completely and carefully , b efore using the Dreambox. The Man ufacturer tak es no resp onsibilit y for damages as a result of incorrect handling of the Dreambox. • Allow enough space around the Dreambox for sufficien t v en tilation.[...]

  • Seite 7

    A dditional safety instructions • (Dis-)Connecting to a LNB: T urn the Dream b o x off b efore y ou connect or disconnect a cable coming from or going to a LNB. • Connecting to a TV: Before connecting or disconnecting y our Dream b o x to/from a TV please turn it off. • In case y ou notice any damage to the p o wer cord or p o w er plug imm[...]

  • Seite 8

    Disp osal instructions The pac kaging of the Dream b o x only consists of reusable materials. Please recycle if p ossible. This symbol on the product or on its packaging indicates that this pro duct must not b e disp osed of with y our other household waste. Instead, it is your resp onsibilit y to disp ose of your w aste equipmen t by handing it ov[...]

  • Seite 9

    1.3 Views 1.3.1 F ront view Smartc ar d-Reader OLED -Display Status-LED IR- Se ns o r Stan dby-But ton Sma rtca rd-Reader Insert y our Dreamcrypt ™ Smartcard with the golden c hip facing do wn and forw ard into one of the tw o Smartcard reader slots. Dreamcrypt ™ is a registered trademark of Dream-Multimedia. OLED-Displa y The OLED-Display show[...]

  • Seite 10

    1.3.2 Rea r view Sc art TV Digi tal Audio Ethernet USB Modem DC 12V SERVICE HDMI Power on/off e SATA 13 /18V = / LN B IN Net work interf ace S/ PDI F optical audio Power connec tor Scar t TV output Power switch 2 U SB 2 . 0 port s Modem co nnector eSA T A p or t HDM I output LNB input Ser vice conne ctor LNB input Connect the coaxial cable from y o[...]

  • Seite 11

    1.4 Remote control SHIF T / SE TUP-But ton DRE AM-Mode -Button Numeric Ke ypad Ar ro w-Lef t - Button Mu te -B ut ton V olume +/ - Buttons INFO-But t on Naviga tions-Buttons AUDIO-But ton Options-Buttons T V- Bu t to n R A DIO - Bu t ton Standby -But t on T V -Mode -Button Arrow-Right -But ton E XIT -B ut ton Bouquet +/- Buttons MENU -B ut ton O K-[...]

  • Seite 12

    SHIFT-Setup-Button The SHIFT/ SETUP-Button is used to preprogram the remote control to op erate a TV. (see Chapter 12 TV-Mo de setup on page 75 ) Standb y-Button The Standb y-Button switc hes your Dream b o x on and off. (see Chapter 3.1 T urning your Dr e amb ox on and off on page 16 ) DREAM-Mo de-Button The DREAM-Mo de-Button switc hes your rem[...]

  • Seite 13

    VIDEO-Button Pressing the VIDEO-Button shows the list of recordings. Options-Buttons All p ossible options are shown by the four colored dots/blo c ks (red, green, yello w, blue) and can b e activ ated by the Options-Buttons . Dep ending on the menu y ou currently are in the options will c hange and will b e named differently . These buttons are m[...]

  • Seite 14

    Chapter 2 Sta rt-up 2.1 Connecting Before using the Dreambox, please read the safety instructions under Chapter 1.1 Safety instructions on page 1 . In the following is describ ed ho w to connect the dreambox to a Satellite-dish, an a/v receiver, a tv-device and a net w ork. 2.1.1 Satellite Dish (D VB-S/S2) Connect the (LNB) with a suitable coax cab[...]

  • Seite 15

    2.1.2 A/V Receiver Connection via optical fib er cable If your a/v receiver (amplifier) has a suitable optcial S/PDIF Input, connect the connection jack Digital A udio at the Dreambox with an optical fib er cable (toslink) with the optcial S/PDIF Input of y our amplifier. Scar t T V Digit al Audio Ethernet USB Modem DC 12V SERVICE HDMI Pow er o[...]

  • Seite 16

    Connection via HDMI cable Use an hdmi-cable to connect the hdmi-out of your dreambox to an hdmi-input of the a/v receiv er. After that tak e a second hdmi-cable for connecting the hdmi-out of y our a/v receiver to the hdmi-input of the tv-device. HDMI HDMI HDMI HDMI Sc art T V Digit al Audio Ethernet USB Modem DC 12V SERVICE HDMI Pow er on/ off eS [...]

  • Seite 17

    2.1.3 T elevision HDMI Connect the dream b o x with the hdmi or scart-cable mit dem TV-input of your television. A t least use the hdmi-in terface for getting the b est picture qualit y (through digital transmission). Y ou can use the supplied HDMI cable for connecting the dreambox with the hdmi-input of y our television. HDMI HDMI Scar t TV Digit [...]

  • Seite 18

    2.1.4 Net w ork Connection via netw ork cable Scar t T V Digit al Audio Ethernet USB Modem DC 12V SERVICE HDMI Pow er on/of f eS ATA 13/ 18V= / L NB IN 13[...]

  • Seite 19

    2.2 T urning the device on 1. Place the batteries inside the battery compartment of the remote con trol k eeping in mind the right p olarit y . 2. Plug in the p o wer cable in to the supplied p o wer supply and connect it to the Dream b o x. The p o w er plug has to b e plugged into a 110V/60Hz or 230V/50Hz p o wer so c k et. 3. No w turn on y our [...]

  • Seite 20

    T uner Detailed information ab out the tuner setup can be found in chapter 7.1 DVB-S2 T uner-Configur ation on page 52 . Default services list/Service scan Dep ending on y our tuner configuration in the previous step, you might b e offered to install default services lists. Otherwise you will b e asked to perform a service scan. Detailed informa[...]

  • Seite 21

    Chapter 3 Basic op eration 3.1 T urning y our Dreamb o x on and off Y our Dreambox has a standby mo de and a so-called deep-standby mo de. Both functions differ in their p o wer consumption and the time which is needed un til the b o x has b o oted. • Standby ab out 1 Second (higher p o w er consumption) • Deep-Standby ab out 1-2 Minutes (les[...]

  • Seite 22

    This is the Standby / R estart -Menu. With the Na vigation-Buttons ( NH ) c ho ose the desired option and press the OK-Button . 3.2 Service selection Pressing the Navigation-Buttons ( JI ) on y our Dreambox remote con trol will take you to the previous or next service. Pressing the 0 on the Numeric-Keypad will enable you to skip bac k and forth bet[...]

  • Seite 23

    3.4 Controlling the volume The V olume +/- Buttons control the volume of the audio. Pressing + will make turn it up and pressing - will turn it do wn. Pressing the MUTE-Button m utes the v olume. A crossed sp eak er symbol will app ear on the screen. 3.5 Changing the audio track Pressing the A UDIO-Button in TV or Radio Mo de. Use the Na vigation-B[...]

  • Seite 24

    3.8 Subtitles F ollo w this steps: 1. In TV- or Radio Mo de press the AUDIO-Button . 2. By pressing the y ello w Options-Button a list with the av ailable subtitles will show up. 3. With the Na vigation-Buttons ( NH ) select a desired subtitle and press the OK-Button to activ ate. The screenshot on the left sho ws you an example of how a subtitle l[...]

  • Seite 25

    3.9 Infoba r The Infobar appears when switching a channel and sho ws all necessary Information about the selected service. By pressing the OK-Button y ou can op en the Infobar if needed! Active tuner Signal level Error r at e Channel name Curre nt time Prog ress b ar Current sh o w Is highlighted yellow as soon as a show is broadcasted encrypted. I[...]

  • Seite 26

    3.10 Electronic Program Guide - EPG The Electronic Program Guide (EPG) sho ws information regarding the curren t tv service (similar to a TV guide). By pressing the INF O-Button in TV-Mo de y ou are sup- plied with detailed information ab out the current show and b y pressing the Navigation button ( I ) afterw ards ab out the next sho w. Pressing t[...]

  • Seite 27

    Single-EPG In this view you are supplied with detailed information ab out the curren tly selected c hannel’s programming. F ollo w this steps: 1. Press the INF O-Button . 2. Press the y ello w Options-Button for getting the “Single-EPG” view. Y ou can also access this view b y pressing: 1. Press and hold the INFO-Button for ab out 2 seconds. [...]

  • Seite 28

    Multi-EPG F ollo w this steps: 1. Press the Info-Button . 2. Press the blue Options-Button for switc hing to “Multi-EPG” view. Use the blue and yello w Options-Buttons to switch b et w een the now, next and mor e views. Pressing the green Options-Button will give you the p ossibility to automatically copy the start and end time of the selected [...]

  • Seite 29

    Time/Date Input Press the Men u-Button in the Multi-EPG view. A windo w will app ear where you can en ter a time and date. After you hav e en tered the desired time and date press the OK-Button to activ ate you selection. Graphical Multi-EPG Y ou ha v e another option to view the EPG of different services and successiv e shows. The Graphical Multi[...]

  • Seite 30

    Time/Date Input Press the Men u-Button in the Multi-EPG view. A windo w will app ear where you can en ter a time and date. After you hav e en tered the desired time and date press the OK-Button to activ ate your selection. 3.11 T eletext (Videotext) Press the T ext-Button to en ter the T eletext. With the EXIT-Button you can lea v e teletext. Keep [...]

  • Seite 31

    service without ha ving to switc h services. Press the OK-Button to select the desired T eletext. This option is only av ailable if more than one service on the current s atellite transp onder actually transmits T eletext information. If this is not the case y ou cannot mak e a selection. Screen fo rmat: Standard mo de 16:9 = on/off Enabling this [...]

  • Seite 32

    3.12 Sleep timer Using the sleep timer y ou can put y our Dream b o x into standby or turn it off after a predeterminedamoun t of time. F ollo w this steps: 1. Press the Men u-Button to op en the main OSD menu. 2. With the Na vigation-Buttons ( NH ) c ho ose the option “Standby / R estart” and press the OK- Button . 3. With the Na vigation-But[...]

  • Seite 33

    Chapter 4 Edit the channellist What is a b ouquet? A bouquet can b e thought of something like a folder. Ev ery c hannel equals a page in this folder and the pages are sorted in to categories. This wa y you can create a bouquet called “K ids” , for example, under which you “file” all c hildren’s stations. Another example w ould be to cre[...]

  • Seite 34

    4.2 A dd a service to favorites If you wan t to add a service to your F a v orites-view you can c ho ose from services in the All-, Satellites- and Pro vider-views . Y ou can switc h views by pressing the red, green, yello w and blue Options- Buttons . At this p oin t we only describ e the pro cess from the All-Bouquet since it is the same for the [...]

  • Seite 35

    4.4 Remove a service from favo rites 1. Press the Na vigation-Buttons ( NH ) to op en the channellist. 2. With the Na vigation-Buttons ( NH ) c ho ose the channel you w ant to delete. 3. By pressing the MENU-Button the “Channel list menu” will op en up. 4. With the Navigation-Buttons ( NH ) c hoose the option “r emove servic e” and press th[...]

  • Seite 36

    6. Press the OK-Button , to add the mark er to y our fa v orites list. If y ou hav e added tw o markers use the Arro w-Left and Arrow-Righ t-Buttons to jump b et ween those t w o mark ers. 4.7 P arental control P aren tal con trol mak es it p ossible to lo ck selected channels. F ollo w this steps: 1. Press the Men u-Button to op en the main OSD me[...]

  • Seite 37

    2. With the Numeric-Keypad enter a 4-digit Pinco de. Y ou hav e to en ter the new pinco de twice to ensure you didn’t make any t yping errors. If you already created a pinco de earlier y ou will b e prompted to en ter the old pinco de and afterwards the new one. Y ou will see a notice that the pinco de has b een changed. If the en tered pincode w[...]

  • Seite 38

    Chapter 5 Ha rd disk op eration Hin t: When using an external eSA T A HDD it must ha v e an o wn p o wer supply!!! 5.1 Installation-Guide This capter describ es how to install a 2,5“ SA T A Hard disk in y our Dream b o x DM800 HD se. Please alw a ys adhere to ESD (Electrostatic Disc harge) regulations when handling electronic devices. • Make su[...]

  • Seite 39

    Op ening the device 1. Unscrew the screw(s) on the left side of y our Dream b o x. Remo v e screw(s) on the left side 2. Unscrew the screw(s) on the righ t side of y our Dream b o x. Remo v e screw(s) on the righ t side 3. Remo v e the mark ed screw(s) on the rear panel. Remo v e mark ed screw(s) on the rear panel 34[...]

  • Seite 40

    4. Lift the co v er off as sho wn b elo w. Lift co v er as sho wn Installation of a 2,5" SA T A Ha rd disk 1. Lift the hard disk cage up w ards. Lift hard disk cage 35[...]

  • Seite 41

    2. Place the hard disk in the cage and ensure that you place the hard disk carefully in to the plug of the hard disk cage. Placing hdd to hard disk cage 3. No w you need a Phillips-tip screwdriver, the hard disk cage, y our hard disk and tw o screws for moun t- ing the hdd. Tigh ten the hard disk with the t w o screws on the left side of the hard d[...]

  • Seite 42

    4. No w remount the hard disk cage in y our Dreambox and ensure the correct fitting of the hard disk cage connector to the slot on the main b oard. Then tigh ten the hard disk cage with 2 screws to the housing of the dream b o x (see figure). Fit hdd cage to dream b o x housing 5. Reassam ble your Dreambox b y following the guide (siehe Punkt 5.1[...]

  • Seite 43

    • 1, 2 or 4 Hours Once y ou ha v e selected the desired time press the OK-Button or the green Options-Button to get bac k in to the harddisk men u. 5.2.1 Initialization 1. Press the Men u-Button to op en the main OSD menu. 2. With the Na vigation-Buttons ( NH ) c ho ose the option “Setup” and press the OK-Button . 3. With the Na vigation-Butt[...]

  • Seite 44

    Pressing the Up/Do wn-Buttons on y our remote con trol activ ates the service list. The recording contin ues in the bac kground. Once a recording is started, no matter if manually or by timer (see Chapter 5.3.3 R e c or ding by timer on page 39 ) it will b e signaled b y a note on the screen. Is the tuner used for recording and y ou are trying to a[...]

  • Seite 45

    • daily • weekly with choice of w eekda y • Monday through F riday • user defined (for each day from Monda y through Sunda y) F or all four options you can set a date for the first execution of the timer Y ou can decide what should happ en after the recording finishes by selecting the “After event” option. Y ou can c ho ose b et w ee[...]

  • Seite 46

    Timerlist Pressing the red Options-Button will delete a timer. The green Options-Button adds a timer, the y ello w Options-Button toggles active on and off (only p ossible in waiting status) and the blue Options- Button remo v es finished timers from the list. With the Na vigation-Buttons ( NH ) c ho ose an existing timer and press the OK-Button [...]

  • Seite 47

    5.4 W atch a recording (Pla yback) 1. Press the Video-Button to get to the selection of recordings. 2. Use the Na vigation-Buttons ( NH ) to select a recording. Press the OK-Button to start pla ying it. List of recordings During replay you can see the control symbols in the Infobar. Press the Na vigation-Buttons ( NH ) or press the VIDEO-Button , t[...]

  • Seite 48

    Skipping in a reco rding Button Time Button 1 10 sec. back Button 4 1 min. back Button 7 5 min. back Skip bac kward Button Time Button 3 10 sec. forward Button 6 1 min. forward Button 9 5 min. forward Skip forw ard Sp o oling in a recording The follo wing sp eeds for sp o oling in a recording are a v ailable: • F orward ( blue Options-Button ): 2[...]

  • Seite 49

    3. With the Na vigation-Buttons ( NH ) choose the option “delete” and press the OK-Button . Y ou will be asked if you w an t to delete the recording. As a control feature the name of the recording is displa y ed as w ell. Cho ose “Y es” and y ou will b e taken bac k to the selection of recordings. 5.7 Movielist options F ollo w this steps: [...]

  • Seite 50

    Chapter 6 Setup 6.1 Language 1. If no OSD men u is visible on y our screen, press the Men u-Button to op en the main OSD men u. 2. With the Na vigation-Buttons ( NH ) c ho ose the option “Setup” and press the OK-Button . 3. With the Na vigation-Buttons ( NH ) c ho ose the option “System” and press the OK-Button . 4. With the Na vigation-But[...]

  • Seite 51

    Infoba r timeout: Set the desired time after which you wan t the Infobar to disappear. Y ou can c ho ose b et ween one and ten seconds or “no timeout” . 6.2.2 Intermediate mo de: These settings supplemen t the settings in simple mo de. Reco rdings alw a ys have prio rity: If this option is set to “Y es” y our Dream box will automatically sw[...]

  • Seite 52

    Video output This option selects to whic h output the video signal will b e sent to. HDMI If y ou hav e connected your TV to the HDMI output of your Dream b o x set the “Output type” option to “HDMI” . Sca rt If y ou hav e connected y our TV to the Scart output of y our Dreambox set the “Output type” option to “Scart” . Mo dus Use t[...]

  • Seite 53

    Mo de Sca rt Select the standard supp orted by your TV screen. This is usually either P AL or NTSC. If y ou o wn a TV screen which supp orts b oth mo des you can also select the Multi option. Y our TV screen will automatically switch dep ending on the input signal. These options are only av ailable ifthe output t yp e is set to “Scart” . Asp ec[...]

  • Seite 54

    Standb y 1. With the Na vigation-Buttons ( NH ) c ho ose the option “Standby” . 2. With the Na vigation-Buttons ( JI ) choose the brightness of the OLED-Display for standby mo de. 6.6 Net wo rk Connection via netw ork cable A dapter-Settings 1. Press the Men u-Button to op en the main OSD menu. 2. With the Na vigation-Buttons ( NH ) c ho ose th[...]

  • Seite 55

    Net w ork test The net w ork test will assist y ou in finding possible sources of error in your netw ork configuration. Press the green Options-Button to start the test or to rep eat it. Press the y ello w Options-Button to ab ort the test. Once the test has finished y ou can get additional information and help to ev ery subitem of the test. Use[...]

  • Seite 56

    The name of the default skin is “Default Skin” . With the Na vigation-Buttons ( NH ) c ho ose your desired skin and press the OK-Button . T o fully activ ate the skin the system needs to b e restarted. Use the Navigation-Buttons ( NH ) to select y our desired option and press the OK-Button. 6.8 F actory reset 1. Press the Men u-Button to op en [...]

  • Seite 57

    Chapter 7 Service sea rching In this c hapter y ou will learn ho w to setup the tunerconfiguration for the reception with a satellite-dish (D VB-S/S2), via cable television (DVB-C) or via digital terrestrial television (D VB-T) in your dreambox and ho w to p erform a service scan. 7.1 D VB-S2 T uner-Configuration 7.1.1 Single satellite – direct[...]

  • Seite 58

    7. With the Na vigation-Buttons ( JI ) c ho ose the option “Single” . 8. With the Na vigation-Buttons ( NH ) c ho ose the option “Satel lite” . 9. With the Na vigation-Buttons ( JI ) c ho ose the desired Satellite. 10. Press the OK-Button to sav e this settings. Y ou are tak en bac k to the “Cho ose tuner” menu. If you ha v e trouble wi[...]

  • Seite 59

    9. With the Na vigation-Buttons ( JI ) c ho ose the desired Satellite. 10. With the Na vigation-Buttons ( NH ) c ho ose the option “Port B” . 11. With the Na vigation-Buttons ( JI ) c ho ose the desired Satellite. 12. Press the OK-Button to sav e this settings. Mak e sure y ou kno w whic h satellite is connected to which input on the T oneburst[...]

  • Seite 60

    9. With the Na vigation-Buttons ( JI ) c ho ose the desired Satellite. 10. With the Na vigation-Buttons ( NH ) c ho ose the option “Port B” . 11. With the Na vigation-Buttons ( JI ) c ho ose the desired Satellite. 12. Press the OK-Button to sav e this settings. Mak e sure y ou kno w whic h satellite is connected to which input on the T oneburst[...]

  • Seite 61

    7. With the Na vigation-Buttons ( JI ) c ho ose the option “DiSEqC A/B/C/D” . 8. With the Na vigation-Buttons ( NH ) c ho ose the option “Port A” . 9. With the Na vigation-Buttons ( JI ) c ho ose the desired Satellite. 10. With the Na vigation-Buttons ( NH ) c ho ose the option “Port B” . 11. With the Na vigation-Buttons ( JI ) c ho ose[...]

  • Seite 62

    2. With the Na vigation-Buttons ( NH ) c ho ose the option “Setup” and press the OK-Button . 3. With the Na vigation-Buttons ( NH ) c ho ose the option “Servic e se ar ching” and press the OK- Button . 4. With the Na vigation-Buttons ( NH ) c hoose the option “T uner c onfigur ation” and press the OK- Button . 5. With the Na vigation-B[...]

  • Seite 63

    4. With the Na vigation-Buttons ( NH ) c hoose the option “T uner c onfigur ation” and press the OK- Button . 5. With the Na vigation-Buttons ( NH ) choose the option “DVB-S2 T uner” and press the OK-Button . 6. With the Na vigation-Buttons ( NH ) c ho ose the option “Configur ation” . 7. With the Na vigation-Buttons ( JI ) c ho ose t[...]

  • Seite 64

    3. With the Na vigation-Buttons ( NH ) c ho ose the option “Servic e se ar ching” and press the OK- Button . 4. With the Na vigation-Buttons ( NH ) c hoose the option “T uner c onfigur ation” and press the OK- Button . 5. With the Na vigation-Buttons ( NH ) c ho ose the “DVB-C T uner” and press the OK-Button . F requency bands This t y[...]

  • Seite 65

    2. With the Na vigation-Buttons ( NH ) c ho ose the option “Setup” and press the OK-Button . 3. With the Na vigation-Buttons ( NH ) c ho ose the option “Servic e se ar ching” and press the OK- Button . 4. With the Na vigation-Buttons ( NH ) c hoose the option “T uner c onfigur ation” and press the OK- Button . 5. With the Na vigation-B[...]

  • Seite 66

    Use the Na vigation-Buttons ( NHJI ) to set the “Cle ar b efor e sc an” option to “Y es” if y ou wan t to delete all services before the scan starts. Otherwise lea v e the setting to “No” whic h results in only new services b eing added to the channel list. In order to find the new services, follow this steps: 1. Press the Na vigation-[...]

  • Seite 67

    Y ou can see the progress of the scan here. The scan is done once you see this menu. It sho ws how man y c hannels w ere found during the scan. Press the OK-Button to store the found channels or the EXIT-Button to cancel. 62[...]

  • Seite 68

    7.5 Manual scan F ollo w this steps: 1. Press the Men u-Button to op en the main OSD menu. 2. With the Na vigation-Buttons ( NH ) c ho ose the option “Setup” and press the OK-Button . 3. With the Na vigation-Buttons ( NH ) c ho ose the option “Servic e se ar ching” and press the OK- Button . 4. With the Na vigation-Buttons ( NH ) c ho ose t[...]

  • Seite 69

    Chapter 8 Systeminfo rmation 8.1 Service This windo w sho ws detailed tec hnical information ab out the current service. Kanal-Informationen F ollo w this steps: 1. Press the MENU-Button in order to op en the main men u. 2. Na vigate to the option “Information” and press the OK-Button . The “Information” men u will op en up. 3. Na vigate to[...]

  • Seite 70

    8.2 Ab out (Ha rd- and Soft w are) This windo w sho ws all relev ant information ab out the Hard- and Soft w are of y our Dream b o x. Hardw are- and Soft w are-Information F ollo w this steps: 1. Press the MENU-Button in order to op en the main men u. 2. Na vigate to the option “Information” and press the OK-Button . The “Information” men [...]

  • Seite 71

    Chapter 9 Up dating the soft w a re 9.1 Backing up y our settings Before installing newer soft w are on your Dream b o x y ou should backup y our settings, otherwise they will b e lost. 1. Press the Men u-Button to op en the main OSD menu. 2. With the Na vigation-Buttons ( NH ) c ho ose the option “Setup” and press the OK-Button . 3. With the N[...]

  • Seite 72

    9.3 Up dating a new soft w a re 9.3.1 using the DreamUP p rogram Ho w do I install new soft w are on m y Dream b o x DM800 HD se ? Requiremen ts: • PC with Windows op erating system • DreamUP softw are (current v ersion under http://www.dreambox.de ) • 1 mini-usb-to-usb cable • 1 netw ork cable (optional but recommended) 1. Firstly disconne[...]

  • Seite 73

    6. Start the DreamUp soft w are on y our PC. 7. Select the com-port which the “mini-USB-to-USB-cable” is connected to, as describ ed ab o v e. In our example “COM4” . 8. Chec k the “U se network” b o x if your PC and Dreambox are connected using a net w ork cable The softw are up date can b e done without netw ork sup- p ort, but it tak[...]

  • Seite 74

    12. After the flash loader has b een transferred to your Dream b o x select the “Flash Box” Button in the DreamUp soft w are. 13. Select the softw are image and click on the “Op en” button. 14. The new soft w are is now being transferred to your Dream b o x. 15. If the pro cess w as successful y ou will get a “Box was flashe d suc c ess[...]

  • Seite 75

    9.3.2 With bro wser With activated DHCP server Requiremen ts: • PC with browser like. Firefox, Op era, Internet Explorer • latest Softw are for your Dream box, do wnloadable under www.dreambox.de • 1 netw orkcable • DHCP-Server Y ou need the image file you w an t to flash (do wnloadable under www.dreambox.de ). Image files ha v e the ext[...]

  • Seite 76

    2. Clic k on “firmwar e up gr ade” on the given site in y our Bro wser. 3. On the next page, you can select the flash image you w an t to flash. Be sure that it has the “ .nfi” extension. Y ou can’t flash other images (lik e .img)! 4. After you selected the desired image clic k on “FLASH!” and w ait. It migh t tak e some time to [...]

  • Seite 77

    Chapter 10 Mo dem If y ou ha v e no option to connect y our dreambox to the internet b y using the ethernet p ort, y ou can also use the built in mo dem for this. 10.1 Connecting Y ou need a connection-cable whic h has got both middle pins of the RJ11-Plug assigned. Connect the RJ11- Plug to the mo dem of the dream b o x and connect the other side [...]

  • Seite 78

    En ter login-data 1. Press the Men u-Button to op en the main OSD menu. 2. With the Na vigation-Buttons ( NH ) c ho ose the option “Plugins” and press the OK-Button . 3. With the Na vigation-Buttons ( NH ) c ho ose the option “Mo dem” and press the OK-Button . 4. By using the Numeric-Keypad en ter y our username , the passw ord and the phon[...]

  • Seite 79

    Chapter 11 T roublesho oting Problem P ossible cause Solution No audio, no video, OLED-Displa y lit F aulty wiring Chec k wiring and connections F aulty LNB Exc hange LNB W rong T uner setting Review settings (see Punkt 7.1 DVB-S2 T uner-Configur ation on p age 52 ) Dish aligned incorrectly Realign dish Beamlik e blac kouts in the video Hea vy rai[...]

  • Seite 80

    Chapter 12 TV-Mo de setup With the Dream b o x remote control you ha v e the p ossibilit y to control the dreambox and y our tv device with only one remote control. In order that your tv device reacts to the signals of the remote con trol, you ha v e to program it b efore. Therefore a 3-digit Co de from our tv co de list has to b e c hosen and en t[...]

  • Seite 81

    Chapter 13 T echnical data • 400 MHz MIPS Prozessor • Linux op erating system • colored OLED display • MPEG2 / H.264 Hardware deco ding (DVB compliant) • T unerv ariations: DVB-S/S2, DVB-C, D VB-T • T uner Mo dule, Plug&Pla y • 2x Smartcard-Reader (Dreamcrypt CA) • Mini-USB Service-Port • 10/100 Mbit compatible Ethernet Interf[...]

  • Seite 82

    A dditional info: DBS-T uner with D VB-S2: F requency Range 950 .... 2150 MHz Demo dulation DVB-S (QPSK); DVB-S2 ((8PSK,QPSK) Sym b ol rate DVB-S: 2 ... 45 Mbaud/s, SCPC/ MCPC D VB-S2: 10 – 31 Mbaud/s (8PSK) , 10 –30 Mbaud/s (QPSK) D VB/C-T uner (plugable): Input/Lo op through Connector IEC 169-24, F emale F requency Range 50 - 870 MHz Signal L[...]

  • Seite 83

    Video parameter: Input Lev el FBAS 1 V ss +/- 0.3 dB on 75 Ohm T eletext filter in conformit y with ETS 300 472 Standard TV-Scart: Output: FBAS,R GB or S-Video Mini USB service connector: F unction: Up date of Firmw are Ethernet: 10/100 Mbit compatible In terface F unction: Up date of Firmw are Analoge mo dem: analoge mo dem for Internet connectio[...]

  • Seite 84

    W eigh t: 940 g without HDD 79[...]

  • Seite 85

    Chapter 14 F eatures • Single-EPG (Electronic Program Guide): sortable by date or alphab etically • Automatic search for additional air dates of a sho w and easy recording them b y timer • Multi-EPG: graphically and text-based • Timeshift • List of recordings: sortable by date or alphab etically and free choice of different views • Tim[...]

  • Seite 86

    Chapter 15 Contact & Supp o rt Info rmation Headquarter & Distribution: Dream-Multimedia Gm bH Pierbusc h 24-26 44536 Lünen German y Dealer’s Hotline: (Dealers only) T el.: +49 (0)180 - 3 44 11 30 992 F ax: +49 (0)180 - 3 44 11 30 993 Y ou can reac h the dealer’s hotline from: Mo - F r. 09:00 am - 12:00 pm and 01:00 pm - 03:00 pm T ec [...]

  • Seite 87

    Dealers & Pricing: E-Mail: info@dream-m ultimedia-tv.de T ec hnical Supp ort: E-Mail: supp ort@dream-m ultimedia-tv.de W ebsite: W eblink: http://www.dreambox.de Supp ort F orum: W eblink: http://www.dreambox.de/board Soft w are Supp ort (actual images): W eblink DM800 HD se: http://www.dm800.de 82[...]

  • Seite 88

    Chapter 16 Cop yright notes © Dream-Multimedia 2011. All righ ts reserv ed. This pro duct contains files that are distributed under differen t licenses, esp ecially a Op en Source License, the GNU General Public License. Y ou can find details ab out this License on the next three pages. A dditional notes ab out the source co de and patc hes und[...]

  • Seite 89

    16.1 GNU GPL (General Public License) GNU GENERAL PUBLIC LICENSE V ersion 2, June 1991 Copyrigh t (C) 1989, 1991 F ree Softw are F oundation, Inc. 51 F ranklin Street, Fifth Flo or, Boston, MA 02110-1301, USA Every one is p ermitted to copy and distribute verbatim copies of this license do cumen t, but changing it is not allow ed. Pream ble The lic[...]

  • Seite 90

    In addition, mere aggregation of another w ork not based on the Program with the Program (or with a work based on the Program) on a volume of a storage or distribution medium do es not bring the other work under the scop e of this License. 3. Y ou may copy and distribute the Program (or a w ork based on it, under Section 2) in object co de or execu[...]

  • Seite 91

    HOLDERS AND/OR OTHER P AR TIES PR OVIDE THE PROGRAM "‘AS IS"’ WITHOUT W ARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED W ARRANTIES OF MERCHANT ABILITY AND FITNESS FOR A P AR TICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PR OGRAM IS WITH YOU. SHOULD THE PROGRAM P[...]