Casablanca Fan Company 6643050 manual

1 INTRODUCTION 1 MOUNTING RECOMMENDA TIONS 2 F AN INST ALLA TION - GETTING ST ARTED 3 CONTROL FEA TURES: 4-SPEED 7 INTELI•TOUCH 9 TROUBLE SHOOTING 10 ADV AN•T OUCH 13 TROUBLE SHOOTING 16 CIRCUIT BREAKER (TRIP BREAKER FOR THE CIRCUIT YOU WILL BE WORKING ON) FUSE BOX (REMOVE FUSE FOR THE CIRCUIT YOU WILL BE WORKING ON) 18 ″ 84 ″ 70 ″ CONTEN[...]

2 MOUNTING RECOMMEND A TIONS SLOPED CEILING INST ALLA TIONS Before mounting your Casablanca fan, read the following helpful recommendations.  e location of the fan, air circulation, and fan size are all important factors to consider before installation. L ocation Ceiling fans have practical uses in almost ever y room in your home. W e suggest yo[...]

3 Using Existing Ceiling F ixture Outlet Box After turning the power OFF at its source (either the circuit breaker or fuse box), lower the old fi xture and disco nnect the wiring. Check the ceiling fi xture outlet box to be sure it is marked “ Approved for Ceiling F an Mounting.” If it is not, a new box must be installed. GETTING ST ARTED Ins[...]

4 Prepar e for f an installation as follo ws: 3a. Route the wir es from th e motor thr ough the P erma • Lock™ downr od and ball assembly . 3b . Usin g the pr ovid ed allen wrench, loosen th e set screw several turn s to allow installati on of th e downr od. Thread the d ownrod in to the m otor coupling un til it stops turning, this will take a[...]

5 Step 5. T o han g the f an body in th e canopy , hold the f an body fi rmly and insert th e ball into th e canopy open- ing. Ch eck that no wir es were pin ched . Rotate the f an body un til the slot in th e nylon ball fi ts into th e pin opposite the canopy openin g. NOTE: Independent control o f the light fi xture using a W-81 requires an ad[...]

6 PROCEED TO Y OUR F AN’S CONTROL FEA TURE SECTION FOR INST ALLA TION/OPERA TING INSTRUCTIONS: 4-SPEED - P A GE 7 | INTELI•TOUCH2 - P AGE 9 Install th e assembled blade an d blade h older to th e motor . Hand tigh ten securely . Repeat for each assembly . FEL T W ASHER (3 PER BLADE) BLADE HOLDER SCREW (2 PER BLADE HOLDER) W ARNING: T o r educe [...]

7 Pull-chain switches on th e fan con trol th e fan an d lights . Usin g the f an contr ol pull-chain switch: Fan off at start. First pull: fan ON, Hi gh speed Second pull: Medium speed Third pull: Medium Low speed Fourth pull: Low speed Fifth pull: Fan OFF Usin g the opti onal li ght pull-chain switch: Li ght off at start. First pull: ligh t ON Se[...]

8 R • The f an may be turn ed ON and OFF by the W-81 wall con trol. • The ligh ts may be turn ed ON and OFF by the W-81 an d the in tensity adjusted from low to hi gh. • The f an must be suppli ed with two ind epend ent 120V A C supply wires . • Set the F AN pull chain switch to the HI GH speed setting. • T urn the li ghts ON at th e fan.[...]

9 R R The wall con trol in stalls in the sam e mann er as an ordinary li ght switch, usin g an existin g juncti on box an d wiring. This contr oller is desi gned to si gnal th e fan micr ocomputer as well as perform n ormal switchin g operati ons . For this reason the followin g precauti ons m ust be observed: 1. Use only th e Casablanca W-32 wall [...]

10 Inteli•T ouch ™ R R Progr ammed into every In teli-T ou ch Series fan is an A utomati c Demon strati on Program. I t can be used to fully dem onstrate an d test the oper ation o f the fan. T o enter the demonstration program: 1. T urn PO WER off f or at least three secon ds. This will clear the f an mem ory ready f or progr amming. 2. T urn [...]

11 The Li ght-Min der pr ogram autom atically turns OFF th e fan m ounted li ghts after two hours . T o enter the Light-Minder Pro gram: 1. T urn th e PO WER OFF for at least three secon ds. 2. T urn the 3. Immedi ately operate th e buttons in th e followin g sequence: + + + + + + 4. A series o f tones in dicates this comm and has been accepted . T[...]

12 Inteli•T ouch ™ Before Requesting Service: Please follo w this troubleshooting guide be- fore contacting your dealer for assistance. Caring for Finishes : For cleanin g, a soft brush or lint-fr ee cloth should be used to pr event scr atching the fi nish. A vacuum clean er brush nozzle can r emove h eavier dust. Surf ace s mudges o r a n a c[...]

13 AD V AN•T OUCH W-62 BRA CKET/HOLSTER REMO V AL Step 1. Remove th e two 6-32 x 5/16” screws holdin g the br acket to the h olster . Save screws for later . AD V AN•T OUCH CONTROL BRACKET INST ALLA TION Standard Light Switch Step A. Remove th e two screws h olding th e switch cover plate . Do not r emove th e cover plate . Step B. Ori ent th[...]

14 Install 4 “ AAA ” alkaline batteries in th e space provi ded. Please observe proper polarity placem ent. Replace Battery Door . Open Battery Door by pressin g down on the in sert tab pro- vide d. AD V AN•T OUCH OPERA TION Fan Operation The A dvan•T ou ch fan is con trolled by the r emote con trol. Th e fan button located in the cen ter t[...]

15 1 ON ECE 23 45 A4 A4 A4 A4 + + + + –– AD V AN•T OUCH CHANGING FREQUENCY SETTING Y ou will ha ve to chang e the dip switch settings in the remote if y ou ar e using more than one fan in the same area and want to contr ol them separately . Step 1. At th e circuit br eaker or fusebo x, turn the power o ff for th e fan you wan t to chang e . S[...]

16 TROUBLESHOO TING Before Requesting Service: Please follow this tr oubleshooting guide before contacting your dealer for assistance. Caring for Finishes : For cleanin g, a soft brush or lint-fr ee cloth should be used to pr event scr atching the fi nish. A vacuum clean er brush nozzle can r emove h eavier dust. Surf ace s mudges o r a n a c - cu[...]