Kantech Ethernet Four-Door Controller KT-400 manual

DN1726-081 1 KT -400 Ethernet Four-Door Controller Installation Manual[...]

[...]

DN1726-081 1 iii KT-400 Ethernet Four-Door Co ntroller Installation Manual Table of Contents Pre-Installation Information ................ ............. .... ............ ............. ............. ................ .................... ............. . 1 Copyright Information ............... ... ................ ................. ................. [...]

DN1726-081 1 iv Configuring the KT-400 Ethernet Fo ur-Door C ontroller with the KT-Finde r ..... ............. ................ ............ 33 Installation Checklist ....... ............. ............. ................ ............. ............. ............. .......................... ............ ... 37 Inputs and Outputs Assignments Sheet ....[...]

DN1726-081 1 1 KT-400 Ethernet Four-Door Co ntroller Installation Manual Pre-Inst allation Information T o the Installer: If you are familiar with the installation, you can use the inst allatio n checklist on p age 37 with the symbol . Copyright Info rmation Copyright © 2008 T yco International Ltd. and it s Respective Comp anies. All Rights R ese[...]

DN1726-081 1 2 T echnical Support For technical assistance with the KT -400 Ethernet Four-Door Controll er and other Kantech products, co ntact technical support, Monday to Friday . See the following tab le for the technical support phone numbers. Country/Region Phone Numbers Support Hours Email North America T oll Free +8 88 222 1560 (GMT -05:00) [...]

DN1726-081 1 3 KT-400 Ethernet Four-Door Co ntroller Installation Manual Compliance Specifications FCC & IC Compliance This device complies with Part 15 of the FCC rules Class A. Ope ration is subject to the following two conditions: (1) this device may not cause harmful interfe rence, and (2) this device must accept any interference received i[...]

DN1726-081 1 4 • 1 GB RAM • Minimum free hard disk space: 20 GB • Color depth: 24-bit (16 million colors ), required for V ideo Integration only • Screen resolution: 1024 x 768 • Graphic adapter card: 32 MB • 48X CD-ROM drive • Network Interface card: 10/100 Ba se-T network adaptor Note: Actual requirements may vary based on yo ur ope[...]

DN1726-081 1 5 KT-400 Ethernet Four-Door Co ntroller Installation Manual Overview The KT -400 Ethernet Four-Door Controller is designed to meet the highest standards o f access control and point monitoring applications. Here ar e the features of the KT -400 Ethernet Four-Door Co ntroller. Comp atible with all EntraPass Speci al, Corporate and Globa[...]

DN1726-081 1 6 Input s There are 16 onboard input s on the KT -400 Ethernet Four-Door Controller. Up to 240 mo re can be added through the addition of exp ansion modules, such as the KT -MOD-INP16, for a total of 256 inputs. Each input can be i ndividually configured for one of th e following application: • Door contact (4 onboard) • T .Rex (Re[...]

DN1726-081 1 7 KT-400 Ethernet Four-Door Co ntroller Installation Manual Downloadable Firmware The firmware program can be downlo aded from any EntraPass workstatio n to th e KT -400 Ethernet Four-Door Controller. The firmware program, stored in the co ntrol ler ’s flash memory , is upgraded without having to change any part s. T rouble and Repor[...]

DN1726-081 1 8 Figure 1: KT -400 Ethernet Four-Door Controller PCB V iew[...]

DN1726-081 1 9 KT-400 Ethernet Four-Door Co ntroller Installation Manual Figure 2: KT -400 Ethernet Four-Door Controller Input s and Outputs V iew 10/100 BASE-T ETHERNET POR T COMPUTER NETWORK KT -300 KT -100 RS485 BUS (COM1) T AMPER NC C NC Z3 NC DRY CONT ACT INPUT DEFINED OPTION WITH DOUBLE EOL RESIST ORS INPUT DEFINED RED BLACK 7 A/H MINIMUM 12V[...]

DN1726-081 1 10 Figure 3 : KT -400 Cabinet Model for North America[...]

DN1726-081 1 11 KT-400 Ethernet Four-Door Co ntroller Installation Manual System Architecture The KT -400 Ethernet Four-Door Controller can be used through va rious site app lications with EntraPass S pecial Edition, EntraPass Corporate Edition and EntraPass Global Editio n. Applications with EntraPass S pecial Edition an d Corporate Edition with C[...]

DN1726-081 1 12 Figure 5 : USB-485 w ith EntraPas s Special Edition a nd Corporate Edition w ith Corpor ate Gatew ay Figure 6 : VC-485 with EntraPass Global Edition and Global or Corporat e Gateway[...]

DN1726-081 1 13 KT-400 Ethernet Four-Door Co ntroller Installation Manual Figure 7 : Over the internet with a KT -NCC and EntraPass Global Edition Figure 8 : Over RS-232 straight from the EntraP ass RS-232 COM port[...]

DN1726-081 1 14 VIT AL LED Heartbeat Patterns Communication st atus and other vital controller p arameters can be obtained fro m VIT AL LED heartbeat patterns. It is located near the RS-232 port (COM3 ), see Figure 1 . This information is p articular ly useful when connecting the controller to the rest o f th e EntraPass system. The fo llow ing t a[...]

DN1726-081 1 15 KT-400 Ethernet Four-Door Co ntroller Installation Manual T echnical Specifications T ype Description Power input ( KT -400 ) T ransformer class 2, IN 120 V AC; OUT 16 V AC, 75 V A Battery back-up ( KT -BA T T -12 ) 12 VDC, 7 Ah battery supervised, provides up to 12 hours of operatio n Operating T emperatures From 2°C to 49 °C (35[...]

DN1726-081 1 16 Electrical S pecifications KT -400 Ethernet Four-Door Controlle r Models, Exp ansion Modules Models, Related Document ation and Miscellaneous Items OPEN COLLECTOR OUTPUTS MAXIMUM CURRENT (T ypical) COMBINED MAXIMUM CURRENT LEDs (LED, OUT1 and OUT2) for each door reader 25 mA (each) 2 Amps for KT -400 Buzzer (Buz) for each door reade[...]

DN1726-081 1 17 KT-400 Ethernet Four-Door Co ntroller Installation Manual DN1475 EntraPass S p ecial Edition, Reference Manual - Sp anish version DN1436 EntraPass Corporate Edition, Reference Manual - Sp anish version DN1599 EntraPass Global Edition, R eference Manual - S panish version DN1514 EntraPass S p ecial Edition, Reference Manual - German [...]

DN1726-081 1 18 Models Information • KT -400 : Cabin et with one KT -400 for North America, up to thr ee expansion modules can be in stalled in the cab inet, • KT -400-PCB : KT -400 with parts, • KT -400-ACC : Acce sso ry ki t, • KT -400-CAB : Cabi net only for North America, T able 2: Models Bill s of Material Note 1: The KT -400 , KT -400[...]

DN1726-081 1 19 KT-400 Ethernet Four-Door Co ntroller Installation Manual Inst alling the KT -400 Ethe rnet Four-Door Controller Preparing to Inst all the KT -400 Ethe rnet Four-Door Controlle r Required to inst all KT -400 Ethernet Four-Door Controller • For North America: AC tr ansformer 120 V AC 60 Hz IN; 16 V AC, 7 5 V A OUT ; cla ss 2 (not i[...]

DN1726-081 1 20 W arning: Controlled door locks may be go verned by regulatory bodies and should always be installed according to local regulations. In most instances, ther e ar e strict limitations to installing fail-secure d evices and fail-safe locking devices such as magnetic locks or other similar locki ng devices on doors used as emergency ex[...]

DN1726-081 1 21 KT-400 Ethernet Four-Door Co ntroller Installation Manual Relay Controlled Output s The KT -400 provides four relay outputs RELA Y1 to RELA Y4 (3 Amps, 30 V AC/VDC). The KT -400 can be exp anded up to 256 controlled outputs when usi ng expansion module s. • The KT -MOD-OUT 16 module provides 16 outp uts at a maximum of 750 mA per [...]

DN1726-081 1 22 Connecting the KT -400 Ethe rnet Four-Door Controller Connecting the VC-485 or the USB-485 to th e RS-485 Bus Connect the RS-485 cable to (COM1) + 485 - and the RS-485 signal grou nd to the 12 VDC AUX - (negative) Controllers are linked together throug h th eir RS-485 terminals. Th e maximum communication loop leng th is 1.2 km (4,0[...]

DN1726-081 1 23 KT-400 Ethernet Four-Door Co ntroller Installation Manual Connecting the Master Controlle r to the Host PC via RS-232 Connect RS-232 cable from KT -400 to the PC (maximum length 30 m (100 ft )) If the local master controller is located more than 30 m (100 f t) from the host computer , you must use a VC-485 or USB-485 interface. Note[...]

DN1726-081 1 24 SPI Exp ansion Port The SPI (Serial Peripheral Interface) expa nsion port on the KT -400 is used to co nnect expansion modules, in order to add more input s and outputs such as relays. The maximum cu rrent draw for the SPI exp ansion port is 500 mA when the 12V AUX terminals are not used. The 6-pin SPI cable must be connected to the[...]

DN1726-081 1 25 KT-400 Ethernet Four-Door Co ntroller Installation Manual Import ant Inst allation Rule s about Exp ansion Modules Note 1: The maximum current draw must be calculate each time there is a new module ad ded to the SPI chain. Rule 2: The SPI cable, between the KT -400 and the 1st module or between each modu les, cannot exceed 1 m (3 ft[...]

DN1726-081 1 26 Figure 10 : PCB View of Exp ansion Modules[...]

DN1726-081 1 27 KT-400 Ethernet Four-Door Co ntroller Installation Manual Figure 1 1 : Example of KT -400 Ethernet Four-Door Controller Interconnection with Exp ansion Modules MOTION DETECTOR BUZZER POWER TAMPER - ++ - NO1 NC1 C1 12 VDC CONT ACT DOOR LOCKING DEVICE BUZZER REGULA TED POWER SUPPL Y 12 VDC, 2 Amps FROM EXTERNAL SOURCE REGULA TED POWER[...]

DN1726-081 1 28 Figure 12 : Exp ansion Modules Cabinet for North America[...]

DN1726-081 1 29 KT-400 Ethernet Four-Door Co ntroller Installation Manual T r oubleshooting T able 3: Reset T ypes and Descriptions Jumpers Heartb eat s Patte rns Reset s Continuous quick flashing Sof t Reset: When JP2 and JP3 are ON, the controller will reset on a) power up, b) pushbutton, or c) EntraPass software 'Manual operator soft reset&[...]

DN1726-081 1 30 Default initialization The KT -400 default initialization or Factory Default DHCP is done at Kantech. The fo llowing steps should only be followed if: a) Y ou want to configure the KT -400 with the KT -Fi nde r , see page 33. b) The KT -400 was communicating via the RS-232 port and y ou have installed a VC-485 or USB-485 to communic[...]

DN1726-081 1 31 KT-400 Ethernet Four-Door Co ntroller Installation Manual KT -400 Ethernet Four-Door Cont roller Maintenance Recommendations The KT -400 includes a lithium i on rechargable battery (see the KT -400 Ethernet Four-Door Controller PCB View on page 8). This battery must be replaced by a Kantech technician to avoid any risk of explosion [...]

DN1726-081 1 32 Configuring the KT -400 Ethernet Four-Door Controller with the W eb Configuration Page This procedure is practical if y ou want to configure the KT -400 in advance before going on site. Optional Documentation Application Note, N etworking Basics , DN17 96. Before you start • The detachable Network Configuration Informatio n Sheet [...]

DN1726-081 1 33 KT-400 Ethernet Four-Door Co ntroller Installation Manual Configuring the KT -400 Ethernet Four -Door Controller with the KT -Finder The KT -Finder is an application used to configure the KT -400 over the local area net work (LAN) or the wide area network (W AN). It doesn’t require any inst allation. Import ant: The KT -Finder app[...]

DN1726-081 1 34 Configuring the KT -400 Ethernet Four -Door Controller with the KT -Finder (continued) 7. Put jumpers on JP2 an d JP3 . 8. V erify your Network Configuratio n In formation Shee t : • Enter the EntraPass IP address or the Domain name of the EntraPass Gateway . This information must be the same as entered in EntraPa ss workstation f[...]

DN1726-081 1 35 KT-400 Ethernet Four-Door Co ntroller Installation Manual KT -400 Ethernet Four-Door Controller Network Configuratio n Information Sheet Please complete one sheet pe r KT -400 Ethernet Four-Door Co ntroller Comp any Name: Site Name: LAN or W AN (see other side) Configuration in a Loc al Area Network (LAN) For more details, refer to [...]

DN1726-081 1 36 Configuration in a Wi de Area Network (W AN) EntraPass Site For more details, refer to the EntraPass Reference Ma nual. EntraPass Special Edition / Corporate Gateway IP Address: ______.______.______.______ Router Public IP Addre ss:______.______. ______.______ or Domain name: ____________________________ Port Forwarding Checklist Fo[...]

DN1726-081 1 37 KT-400 Ethernet Four-Door Co ntroller Installation Manual Inst allation Checklist T o the Inst aller: If you are familiar with the inst allation, you can use the checklist with the symbol. Inst alling the KT -400 Ethe rnet Four-Door Controller Preparing to inst all the KT -400 Ethe rnet Four-Door Controlle r Required to install KT -[...]

DN1726-081 1 38 Input s and Output s Assignment s Sheet Doors DOOR 1 CONT ACT REX DOOR 2 CONT ACT REX DOOR 3 CONT ACT REX DOOR 4 CONT ACT REX Inputs DOOR Z1 NO or NC EOL, DRY or DEOL REX Z2 NO or NC EOL, DR Y or DEOL INPUT Z3 NO or NC EOL, DRY or DEOL INPUT Z4 NO or NC EOL, DRY or DEOL DOOR Z5 NO or NC EOL, DRY or DEOL REX Z6 NO or NC EOL, DR Y or [...]

DN1726-081 1 39 KT-400 Ethernet Four-Door Co ntroller Installation Manual Figure 14: KT -400 Cabinet Inner Door S ticker Diagram ( North America) Figure 15[...]

DN1726-081 1 40[...]