Lincoln Electric 1998 Continental manual

Before driving Introduction 2 Instrumentation 3 Controls and features 26 Seating and safety restraints 71 Starting and driving Starting 90 Driving 95 Roadside emergencies 109 Servicing Maintenance and care 126 Capacities and specifications 160 Reporting safety defects 166 Index 167 All rights reserved. Reproduction by any means, electronic or mecha[...]

ICONS Indicates a warning. Read the following section on W arnings for a full explanation. Indicates vehicle information related to recycling and other environmental concerns will follow . Correct vehicle usage and the authorized disposal of waste cleaning and lubrication materials are significant steps towards protecting the environment. W ARNINGS[...]

Instrumentation 3[...]

RESUME SET ACCEL COAST OFF ON 80 MPH km/h ABS P ! BRAKE + — RPMx1000 N O R M T/C OFF C H E F FILL ON RIGHT SERVICE ENGINE SOON AIR BAG TURN ON HEAD LAMPS 0 1 2 3 4 56 7 0 20 60 80 100 120 0 20 40 60 100 120 140 160 180 200 40 OFF HI LO P 0FF LIGHTS AUTO LAMP SRS Headlamp control (pg. 26) T urn signal and wiper/washer control (pg. 35) Instrument c[...]

NEXT MODE VOL TEMP FAN 000000.0 SYSTEM DRIVER ID MENU TRIP RESET SELECT DISPLAY DTE ECON VEHICLE HANDLING N I T N O C L A T N E VOL PUSH ON TAPE MUTE SEEK TUNE AM FM REW FF SIDE 1 2 COMP SHUFF EXT OFF MAX A/C CD EJ RDS SCAN AUTO AUTO 12 3 4 56 FRONT REAR BASS TREB SEL BAL FADE HI HI OFF OFF BACK BOTH BOTH BACK 0 0 HEATED SEATS Electronic sound syst[...]

W ARNING LIGHTS AND CHIMES Service engine soon Y our vehicle is equipped with a computer that monitors the engine’ s emission control system. This system is commonly known as the On Board Diagnostics System (OBD II). This OBD II system protects the environment by ensuring that your vehicle continues to meet government emission standards. The OBD [...]

These temporary malfunctions can be corrected by filling the fuel tank with good quality fuel and/or properly installing and securely tightening the gas cap. After three driving cycles without these or any other temporary malfunctions present, the Service Engine Soon light should turn off. (A driving cycle consists of a cold engine startup followed[...]

Anti-lock brake system (ABS) Momentarily illuminates when the ignition is turned to the ON position and the engine is off. If the light remains on, continues to flash or fails to illuminate, have the system serviced immediately . T urn signal Illuminates when the left or right turn signal or the hazard lights are turned on. If one or both of the in[...]

Engine oil pressure Illuminates when the oil pressure falls below the normal range. Stop the vehicle as soon as safely possible and switch off the engine immediately . Check the oil level and add oil if needed. Refer to Engine oil in the Maintenance and Care chapter . This lamp also illuminates when the ignition is turned to ON and the engine is of[...]

GAUGES Fuel gauge Displays approximately how much fuel is in the fuel tank (when the key is in the ON position). The fuel gauge may vary slightly when the vehicle is in motion. The ignition should be in the OFF position while the vehicle is being refueled. When the gauge first indicates empty , there is a small amount of reserve fuel in the tank. W[...]

T achometer Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer in the red zone may damage the engine. Engine coolant temperature gauge Indicates the temperature of the engine coolant. At normal operating temperature, the needle remains within the normal area (the area between the “H” and “C”). If it e[...]

ELECTRONIC MESSAGE CENTER The electronic message center only works when the ignition is in the ON position. The message center tells you about the condition of your vehicle by two methods: • operator selectable features • continuous warning reporting of monitored systems Y ou can select different features for the message center to display by us[...]

System check Pressing this control causes the message center to cycle through a status of each of the systems being monitored. For each of the monitored systems, the message center will indicate either an OK message or a warning message for three seconds. The sequence of the system check report is as follows: • voltage level • engine temperatur[...]

Door Ajar Cannot be reset Driver’ s Door Ajar Check Engine T emp W arning returns after 10 minutes T ransmission Overheat Check T ransmission Low Oil Level Check Charging System Low Fuel Level Low Engine Coolant Low T ire Pressure (if equipped) Gear Display Data ERR W arning reappears after key is turned from OFF to ON Brake Lamp Out Check T ract[...]

DTE/ECON • Press the DTE/ECON control once to display the approximately how far you can drive before running out of fuel, or the distance to empty (DTE). T o ensure accuracy , turn the ignition OFF when you fill the tank. • Press the DTE/ECON control a second time to display the average fuel economy in liters/100 kilometers or miles/gallon, bas[...]

RESET Press this control to reset: • warnings • average fuel economy • trip odometers The other selectable features are unaffected by pressing RESET . DISPLA Y Press this control to turn the message center display off. Press it again to turn the display on. W arnings override an off display and must be reset for the display to be off again. V[...]

T raction control Refer to T raction Control y for more information. Express window • Standard vehicle setting is saved as vehicle setting only (not the Driver 1 or 2 individualized profiles). • Standard vehicle with Memory Profile System: setting may be saved to either Driver 1 or 2 personalized profiles or as a vehicle setting. • Settings: [...]

• Standard vehicle with Memory Profile System: setting may be saved to either the Driver 1 or 2 personalized profiles or as a vehicle setting. • Settings: ON or OFF . • Original setting: ON. • Setting adjustment is made using the message center MENU/SELECT controls. Reverse mirrors • Standard vehicle: setting is saved as vehicle setting o[...]

Autolamp on/delay time Standard vehicle with Memory Profile System: setting may be saved to either the Driver 1 or 2 personalized profiles or as a vehicle setting. Instrument panel dim control setting • Standard vehicle: setting is saved as vehicle setting only (not the Driver 1 or 2 individualized profiles). • Standard vehicle with Memory Prof[...]

settings (not individualized settings). T o change a feature setting see Driver profile features in this section. Associated systems Keyless Entry System Programming personalized codes: W ith a key and/or Key FOB outside of the vehicle: • Enter the factory code • Press the 1/2 control • Enter the five digit personalized code Press: • The 1/[...]

Driver profile features Express window • Standard vehicle-setting is saved as vehicle setting only (not the DRIVER MEMOR Y 1 or 2 individualized profiles). • Standard vehicle with Memory Profile System-setting may be saved to either the DRIVER MEMOR Y 1 or 2 personalized profiles or as a vehicle setting. • Settings-ON or OFF • Original sett[...]

Easy entry/exit seat access • Standard vehicle-setting is saved as vehicle setting only (not the DRIVER MEMOR Y 1 or 2 individualized profiles). • Standard vehicle with Memory Profile System-setting may be saved to either the DRIVER MEMOR Y 1 or 2 personalized profiles or as a vehicle setting. • Settings-ON or OFF • Original setting-ON • [...]

• Standard vehicle with Memory Profile System-setting may be saved to either the DRIVER MEMOR Y 1 or 2 personalized profiles or as a vehicle setting. • Settings-low , normal, high • Original setting-normal • Setting adjustment made using: Message Center -VEHICLE HANDLING/SELECT controls Autolamp on/delay time • Standard vehicle with Memor[...]

• Standard vehicle with Memory Profile System-setting may be saved to either the DRIVER MEMOR Y 1 or 2 personalized profiles or as a vehicle setting. • Settings-horizontal and vertical • Original setting-N/A • Setting adjustment made using: outside mirror control Basic operation In order for the system to be able to store or recall an indiv[...]

Memory Profile System (if equipped) The Memory Profile System allows the two primary drivers to select and save individualized preferences for the following eleven vehicle features: • Express window • Auto door locks • Horn chirp • Easy entry/exit seat access • Reverse mirrors • Adjustable ride • Adjustable steering • Autolamp on/de[...]

HEADLAMP CONTROL Rotate the headlamp control to the first position to turn on the parking lamps only . Rotate to the second position to also turn on the headlamps. Daytime running lamps (DRL) (if equipped) T urns the highbeam headlamps on with a reduced output. T o activate: • the engine must be running • the headlamp control is in the OFF or P[...]

INSTRUMENT P ANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel during headlight and parklamp operation. • Push up to brighten. • Push down to dim. AUT OLAMP CONTROL The autolamp system provides light sensitive automatic on-off control of the exterior lights normally controlled by the headlamp control. The autolamp system [...]

T urning the EA TC of f Press OFF . The Outside T emperature (EXT) function will continue to operate until the ignition is turned off. Automatic operation Press AUTO and select the desired temperature. The selected temperature and the word AUTO will appear in the display window . The EA TC system will either heat or cool to achieve the selected tem[...]

T o control the temperature, select any temperature between 18°C (65°F) and 29°C (85°F) by pressing the temperature control. For continuous maximum cooling, push the temperature control until 16°C (60°F) is shown in the display window . The EA TC will continue maximum cooling (disregarding the displayed temperature) until a warmer temperature[...]

steering wheel control up for higher fan speed or down for lower fan speed. The display will show and a bar graph to indicate manual fan operation and relative speed. T o return to automatic fan operation, press AUTO. Manual override controls The override controls allow you to determine where airflow is directed. T o return to full automatic contro[...]

provided in this mode. The air will be heated or cooled based on the temperature selection. For added customer comfort, the air distributed through the floor ducts will be slightly warmer than the air sent to the instrument panel registers. • -Allows for maximum heating by distributing outside air through the floor ducts. However , the air cannot[...]

changed, then the outside temperature will return to the window along with the override selection. The outside temperature reading is most accurate when the vehicle is moving. Higher readings may be obtained when the vehicle is not moving. The readings that you get may not agree with temperatures given on the radio due to differences in vehicle and[...]

The rear defroster control is located on the instrument panel. Press the defroster control to clear the rear window of thin ice and fog. • The small LED will illuminate when the defroster is activated. The ignition must be in the ON position to operate the rear window defroster . The defroster turns off automatically after 10 minutes or when the [...]

POSITIONS OF THE IGNITION 1. ACCESSOR Y , allows the electrical accessories such as the radio to operate while the engine is not running. 2. LOCK, locks the steering wheel, automatic transmission gearshift lever and allows key removal. 3. OFF , shuts off the engine and all accessories without locking the steering wheel. 4. ON, all electrical circui[...]

TURN SIGNAL CONTROL • Push down to activate the left turn signal. • Push up to activate the right turn signal. Cornering lamps (if equipped) When the turn signal is used when the headlamps are on, the cornering lamps will light either the right or left side depending on the direction of the turn. The flash rate of the turn signal will speed up [...]

Speed sensitive volume The recommended level for speed sensitive volume is from level 1 through level 3. Level 0 turns the speed sensitive volume off and Level 7 is the maximum setting for the speed sensitive volume. Climate control features • Press TEMP up or down to adjust temperature. • Press F AN up or down to adjust fan speed. SPEED CONTRO[...]

T o turn speed control off • Press OFF or • T urn off the vehicle ignition. Once speed control is switched off, the previously programmed set speed will be erased. When the OFF control is pressed, the message “SPEED CONTROL OFF” will appear for 5 seconds in your message center . T o set a speed • Press SET ACC/SET ACCEL. For speed control[...]

Do not use the speed control in heavy traffic or on roads that are winding, slippery , or unpaved. T o set a higher set speed • Press and hold SET ACC/SET ACCEL. Release the control when the desired vehicle speed is reached or • Press and release SET ACC/SET ACCEL. Each press will increase the set speed by 1.6 km/h (1 mph) if (E) English is sel[...]

• Depress the brake pedal. When the desired vehicle speed is reached, press SET ACC/SET ACCEL. When the COAST or SET ACCEL control is pressed and released, the message “SPEED CONTROL SET” will appear for 5 seconds in your message center . T o disengage speed control • Depress the brake pedal. When the brake pedal is depressed, the message ?[...]

T ILT STEERING Pull the tilt steering control toward you to move the steering wheel up or down. Hold the control while adjusting the wheel to the desired position, then release the control. Never adjust the steering wheel when the vehicle is moving. INTERIOR LAMPS Map lamps T o turn on the map lamps, press the control next to each lamp. If equipped[...]

Rear courtesy/reading lamps The courtesy lamp lights when: • any door is opened. • when the instrument panel dimmer switch is turned to the courtesy lamp position. • if any of the keyless entry keypad controls are pressed and the ignition is OFF . W ith the ignition key in the ACC or ON position, the reading lamp can be turned on by pressing [...]

1. By pressing the Information control. 2. By pressing the Emergency (S.O.S) control. 3. The system will automatically activate if the vehicle’ s air bags have been deployed. Quick summary • T o utilize your vehicle’ s RESCU system, your cellular phone must be activated. • Information or emergency assistance can be requested whenever your k[...]

• T ypically , voice communication with an operator is established within one minute after an assistance control is pressed. • The operator verbally obtains details of your situation and, if necessary , ties your vehicle into a three-way phone call with the United States Auto Club or local 911 or other emergency services to dispatch the appropr[...]

• Last recorded speed and direction of the vehicle • T ime tag identifying when last position was taken • Call-back phone number After the transmission is complete, the call is forwarded to an operator who will verify the details of the request and confirm the vehicle’ s location using a computerized map. Information icon The Information ic[...]

Activation and deactivation When either of the two Lincoln RESCU controls are pressed, or the air bags are deployed (this will activate the system as an emergency automatically), a warning light, located in the overhead console, will begin to flash and status messages will be displayed on the vehicle’ s message center , confirming an assistance r[...]

• INFORMA TION REQUEST , EMERGENCY REQUEST or AIR BAG REQUEST • CALL IN PROGRESS • RINGING RESPONSE CENTER • SENDING LOCA TION DA T A • DA T A RECEIVED • W AITING FOR OPERA TOR Once an assistance request is made, it will typically take less than one minute until contact is made with an operator . During voice communication the following[...]

Similarly , if the cellular call is disconnected by the network prior to receipt of the termination tone, another call to the response center will also automatically be dialed. The message “REDIAL IN PROGRESS” will be displayed on the message center and voice communication with an operator will be restored. During redial calls, full control of [...]

Lincoln RESCU system limitations Inoperative if cellular phone inactive or inoperative Lincoln RESCU utilizes your vehicle’ s cellular phone and will not operate if cellular service has not been activated or if the phone is inoperative. Inoperative if battery discharged or disconnected Lincoln RESCU is powered by the vehicle’ s battery and will[...]

Inoperative if cellular signal marginal or unavailable Since the Lincoln RESCU System utilizes the vehicle’ s cellular phone, it can only be operated in geographical areas with cellular coverage. Although approximately 90 percent of the U.S. population lives and works in cellular coverage areas, there are various rural or mountainous areas where [...]

features and must be avoided. Operation is possible with no incoming calls, call forwarding, busy/no answer transfer and call waiting, but these features could impact overall system performance. Because carriers are regularly making new features available to customers, this list may not be complete. Contact you dealer for assistance if you are unsu[...]

Optional password selection/false activations At the time of your registration, you will be given the option of establishing a user password. All aspects of your service will be identical regardless of your password decision except the way false emergency activations are handled. If established, the password will be requested by the operator to con[...]

Security Response Center . After your initial service period expires, you may be requires to pay a monitoring service fee. Y our dealer can provide you with specific information regarding post-initial service period fees. Relinquishing your vehicle At the time you relinquish your vehicle, it is important that you contact the Lincoln Security Respon[...]

and gates, and can also control home or office lighting and security systems (with the available accessory package). When programming your HomeLink t Universal T ransmitter , you will be operating the garage door or gate. Be sure that people and objects are out to the way to prevent potential harm or damage. Do not use the HomeLink t Universal T ra[...]

If you do not successfully program the HomeLink t Universal T ransmitter after repeated attempts, refer to T raining a rolling code which follows or call toll-free customer assistance: 1–800–355–3515. Note to Canadian residents During programming, your hand-held transmitter may automatically stop transmitting after two seconds which may not b[...]

1. Locate the training control on the garage door opener receiver . Refer to the garage door opener manual or call 1–800–355–3515 if there is difficulty locating the training control. 2. Press the training control on the garage door opener receiver until the training light (next to the control) begins to flash (1-2 seconds). 3. Press the prog[...]

calibration may be necessary . Refer to Compass calibration adjustment . Most geographic areas (zones) have a magnetic north compass point that varies slightly from the northerly direction on maps. This variation is four degrees between adjacent zones and will become noticeable as the vehicle crosses multiple zones. A correct zone setting will elim[...]

5. Release the switch, then slowly press it down again. Press the switch repeatedly until the correct zone setting for your geographic location is displayed on the upper right corner of the mirror . 6. T o exit the zone setting mode, release pressure from the switch for greater than two seconds. Compass calibration adjustment Perform this adjustmen[...]

Press the control to turn the mirror on or off. The mirror will automatically return to the normal state whenever the vehicle is placed in R (reverse)(when the mirror is on) to ensure a bright clear view when backing up. Do not clean the housing or glass of any mirror with harsh abrasives, fuel or other petroleum-based cleaning products. On vehicle[...]

POWER WINDOWS Press and hold the rocker switches to open and close windows. • Press the top portion of the rocker switch to open. • Pull the top portion of the rocker switch to close. Express down T o make the driver window open fully without holding the window control, press the driver window control completely down and release quickly . Depre[...]

Window lock The window lock feature allows only the driver to operate the power windows. T o lock out all the window controls except for the driver’ s press the right side of the control. Press the left side to restore the window controls. Accessory delay W ith accessory delay , the window switches may be used for up to ten minutes after the igni[...]

3. Return to the center position to lock mirrors in place. Heated outside mirrors Both mirrors are heated automatically to remove ice, mist and fog when the rear window defrost is activated. Do not remove ice from the mirrors with a scraper or attempt to readjust the mirror glass if it is frozen in place. These actions could cause damage to the gla[...]

CENTER CONSOLE (IF EQUIPPED) Y our vehicle is equipped with a variety of console features. These include: • utility compartment • cupholders • ashtray and lighter • compact disc changer (if equipped) • power point • cellular phone (if equipped) Use only soft cups in the cupholder . Hard objects can injure you in a collision. Compact dis[...]

POSITIVE RETENTION FLOOR MA T Position the floor mat so that the eyelet is over the pointed end of the retention post and rotate forward to lock in. Make sure that the mat does not interfere with the operation of the accelerator or the brake pedal. T o remove the floor mat, reverse the installation procedure. PERIMETER ALARM SYSTEM (IF EQUIPPED) Ar[...]

If a door is open, the system is prearmed and is waiting for the door to close. The anti-theft indicator on the instrument panel will be lit continuously when the system is prearmed. Once the doors are closed, the system will arm in 30 seconds. Disarming the system Y ou can disarm the system by any of the following actions: • Unlock the doors by [...]

If one or both of your SecuriLock y keys are lost or stolen and you want to ensure the lost or stolen key will not operate your vehicle, bring your vehicle and all available SecuriLock y keys to your dealership for reinitialization. REMOTE ENTRY SYSTEM The remote entry system allows you to lock or unlock all vehicle doors without a key . The remote[...]

Opening the trunk Press the control once to open the trunk. Be certain the trunk is closed before driving your vehicle. The trunk may appear closed, but it may not be latched. Failure to do so may cause objects to fall out of the trunk or block rear view vision. Sounding a panic alarm Press this control to activate the alarm. T o deactivate the ala[...]

• structures around the vehicle • other vehicles parked next to the vehicle T o replace the battery: 1. T wist a thin coin between the two halves of the transmitter near the key ring. DO NOT T AKE THE FRONT P ART OF THE TRANSMITTER AP ART . 2. Place the positive (+) side of new battery in the same orientation. Refer to the diagram inside the tr[...]

The inside lights will not turn off if: • they have been turned on with the dimmer control or • any door is open. The battery saver will shut off the interior lamps 40 minutes after the ignition has been turned to the OFF position. KEYLESS ENTRY SYSTEM W ith the keyless entry keypad, you can: • lock or unlock the vehicle doors without using t[...]

• 3/4 recalls personality 2 • 9/0 does not recall a personality All of the vehicle doors will lock and unlock to confirm programming of the new code. Each personality driver profile (personality 1 or personality 2) can be associated with only one personal code. The factory-set code cannot be associated with a personality profile. Do not set a c[...]

After the factory-set code or personal code has been entered, you can unlock all doors (press 3/4) and release the trunk (press 5/6) as long as the controls are pressed within 5 seconds of each other . Locking doors with the keyless entry system It is not necessary to enter the factory-set code prior to locking all doors. T o lock the doors: 1. Pre[...]

SEA TING Head restraints Push or pull the head rests to the desired position. Adjusting the power front seats – door mounted controls The controls for the power seats are located on the inside of each front door . Never adjust the driver’ s seat or seatback when the vehicle is moving. Do not pile cargo higher than the seatbacks to avoid injurin[...]

Press to move the seat forward or backward. Press to move the front portion of the seat cushion up or down. Press to move the rear portion of the seat cushion up or down. Seating and safety restraints 72[...]

Heated seats (if equipped) T o operate the heated seats: • Slide the control to BACK to heat the seatback only . • Slide the control to BOTH to heat the seatback and the seat cushion. • Rotate the thumbwheel to select the desired heat (from 0 (OFF) to 5 (HI)). Allow five minutes for the heat level to stabilize. If the heated seat switch is no[...]

Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision. All occupants of the vehicle, including the driver , should always wear their safety belts. It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people rid[...]

2. T o unfasten, push the red release button and remove the tongue from the buckle. The front and rear outboard safety restraints in the vehicle are combination lap and shoulder belts. The front and rear seat passenger outboard safety belts have two types of locking modes described below: V ehicle sensitive mode The vehicle sensitive mode is the no[...]

How to use the automatic locking mode • Buckle the combination lap and shoulder belt. • Grasp the shoulder portion and pull downward until the entire belt is extracted. • Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode. How to disengage the au[...]

Front safety belt height adjustment Y our vehicle has safety belt height adjustments for the driver and front passenger . Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder . T o lower the shoulder belt height, push the button and slide the height control down. T o raise the height of the shoulder belt, slid[...]

Insert the tongue into the correct buckle. T o lengthen the belt, turn the tongue at a right angle to the belt and pull across your lap until it reaches the buckle. T o tighten the belt, pull the loose end of the belt through the tongue until it fits snugly across the hips. Shorten and fasten the belt when not in use. Safety belt extension assembly[...]

Conditions of operation If... Then... The driver’ s safety belt is not buckled before the ignition switch is turned to the ON position... The safety belt warning light illuminates for one to two minutes and the warning chime sounds for four to eight seconds. The driver’ s safety belt is buckled while the indicator light is illuminated and the w[...]

AIR BAG SUPPLEMENT AL RESTRAINT SYSTEM (SRS) Important supplemental restraint system (SRS) precautions The supplemental restraint system is designed to: • work with the safety belt to protect the driver and right front passenger . • reduce certain upper body injuries. Failure to follow these instructions will affect the performance of the safet[...]

Do not place objects or mount equipment on or near the air bag cover on the steering wheel or in front seat areas that may come into contact with a deploying air bag. Failure to follow this instruction may increase the risk of personal injury in the event of a collision. Do not attempt to service, repair , or modify the Air Bag Supplemental Restrai[...]

The air bags inflate and deflate rapidly upon activation. After air bag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.g., baking soda) that result from the combustion process that inflates the air bag. Small [...]

section in the Instrumentation chapter . Routine maintenance of the air bag is not required. A difficulty with the system is indicated by one or more of the following: • The readiness light will either flash or stay lit. • The readiness light will not illuminate immediately after ignition is turned on. • A series of five beeps will be heard. [...]

Children and safety belts Children who are too large for child safety seats (as specified by your child safety seat manufacturer) should always wear safety belts. Follow all the important safety restraint and air bag precautions that apply to adult passengers in your vehicle. If the shoulder belt portion of a combination lap and shoulder belt can b[...]

When installing a child safety seat: • Use the correct safety belt buckle for that seating position. • Make sure the tongue is securely fastened in the buckle. • Keep the buckle release button pointing up and away from the safety seat, with the tongue between the child seat and the release button, to prevent accidental unbuckling. • Place s[...]

Air bag can kill or injure a child in a child seat. If you must use a forward-facing child seat in the front seat, move seat all the way back. 2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together . 3. While holding the shoulder and lap belt portions together , route the tongue through the child seat according to [...]

5. T o put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode. 7. Pull the lap belt portion across the child seat toward the buck[...]

Installing a child safety seat in the center seating position with adjustable lap belt 1. Lengthen the lap belt. T o lengthen the belt, hold the tongue so that its bottom is perpendicular to the direction of webbing while sliding the tongue up the webbing. 2. Place the child safety seat in the center seating position. 3. Route the tongue and webbin[...]

trim panel, which is behind the rear seat back. T o use this anchorage, do the following: 1. Open the hinged cover located at the front of the high mount stop light. This cover conceals the tether strap anchor bracket. T o prevent damage to the hinge, do not raise the hinged cover of the trim panel beyond its limit. 2. Install the tether strap brac[...]

PREPARING TO START YOUR VEHICLE Engine starting is controlled by the ignition system. This system meets all Canadian Interference-Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise. When starting a fuel-injected engine, avoid pressing the accelerator before or during starting. Only use the accele[...]

2. Make sure the headlamps and vehicle accessories are off. • Make sure the parking brake is set. • Make sure the gearshift is in P (Park). 3. T urn the key to 4 (ON) without turning the key to 5 (ST ART). BRAKE RELEASE HOOD 1 2 3 4 5 Starting 91[...]

Make sure the corresponding lights illuminate briefly . If a light fails to illuminate, have the vehicle serviced. • If the driver’ s safety belt is fastened, the light ( ) will not illuminate. ST ARTING THE ENGINE 1. T urn the key to 5 (ST ART) without pressing the accelerator pedal and release as soon as the engine starts. The key will return[...]

Using the engine block heater (if equipped) An engine block heater warms the engine coolant, which improves starting, warms up the engine faster and allows the heater -defroster system to respond quickly . Use of an engine block heater is strongly recommended if you live in a region where temperatures reach -23°C (-10°F) or below . For best resul[...]

Important ventilating information If the engine is idling while the vehicle is stopped in an open area for long periods of time, open the windows at least 2.5 cm (one inch). Adjust the heating or air conditioning (if equipped) to bring in fresh air . Improve vehicle ventilation by keeping all air inlet vents clear of snow , leaves and other debris.[...]

BRAKES Y our brakes are self-adjusting. Refer to the “Service Guide” for scheduled maintenance. Occasional brake noise is normal and often does not indicate a performance concern with the vehicle’ s brake system. In normal operation, automotive brake systems may emit occasional or intermittent squeal or groan noises when the brakes are applie[...]

light will remain on and your vehicle should be serviced as soon as possible. Normal braking is still effective unless the BRAKE warning lamp is also illuminated. Using ABS • In an emergency or when maximum efficiency from the ABS is required, apply continuous full force on the brake. The ABS will be activated immediately , thus allowing you to r[...]

Y our vehicle has an automatic parking brake release. T o release the parking brake: 1. T urn the ignition to the RUN position. 2. Press the brake pedal. 3. Move the gearshifter from the P (Park) position to one of the forward gears (the parking brake will not release automatically when you shift into reverse). The brake pedal must remain pressed w[...]

sound coming from the engine compartment and the engine will not “rev-up” when you push further on the accelerator . This is normal system behavior . If you should become stuck in snow or on a very slippery road surface, try switching the T raction Control y system off. This may allow excess wheel spin to “dig” the vehicle out or enable a s[...]

The air suspension shut-off switch is located on the left side of the trunk. If this switch is in the OFF position, the rear air suspension will not operate. On vehicles equipped with Air Suspension, turn OFF the Air Suspension switch prior to jacking, hoisting or towing your vehicle. Normal vehicle operation does not require any action by the driv[...]

on the accelerator in each gear . Do not rock the vehicle for more than a few minutes, because it could damage the vehicle. Always set the parking brake fully and make sure the gearshift is latched in P (Park). T urn off the ignition whenever you leave your vehicle. Driving with a 4–speed automatic transaxle Y our automatic overdrive transaxle pr[...]

R (Reverse) W ith the gearshift in R (Reverse), the vehicle will move backward. Y ou should always come to a complete stop before shifting into and out of R (Reverse). N (Neutral) W ith the gearshift in the N (Neutral) position, the vehicle can be started and is free to roll. Hold the brake pedal down while in this position. Driving 101[...]

D (Overdrive) The overdrive position is the normal driving position for an automatic overdrive transaxle. It works the same way as 3 (Third) but shifts to a fourth gear — an overdrive gear — when your vehicle cruises at a constant speed for any length of time. This fourth gear will increase your fuel economy when you travel at cruising speeds. [...]

1 (First) Use 1 (First) for when added engine braking is desired when descending steep hills. The automatic transaxle will shift to the proper gear to ascend any grade without any need to shift to 1 (First). Do not go faster than 61 km/h (38 mph) when in this gear . Y ou can upshift from 1 (First) to overdrive at any time. When parking, do not use [...]

VEHICLE LOADING Before loading a vehicle, familiarize yourself with the following terms: • Base Curb W eight : W eight of the vehicle including any standard equipment, fluids, lubricants, etc. It does not include passengers or aftermarket equipment. • Payload : Combined maximum allowable weight of cargo, passengers and optional equipment. The p[...]

Do not exceed the GVWR or the GA WR specified on the Safety Compliance Certification Label. Do not use replacement tires with lower weight capacities than the originals because they may lower the vehicle’ s GVWR and GA WR limitations. Replacement tires with a higher weight limit than the originals do not increase the GVWR and GA WR limitations. T[...]

Do not exceed the GVWR or the GA WR specified on the Safety Compliance Certification Label. T owing trailers beyond the maximum recommended gross trailer weight could result in engine damage, transmission/axle damage, structural damage, loss of control, and personal injury . Preparing to tow Use the proper equipment for towing a trailer , and make [...]

trailer’ s lamps, see your Lincoln dealer . Be sure to follow their instructions carefully . If you do not install trailer lights correctly , you may cause damage to the vehicle’ s lighting system or other vehicle systems. Driving while you tow Do not drive faster than 88 km/h (55 mph) when towing a trailer . Speed control may shut off if you a[...]

FUEL CONSUMPTION Fuel economy can be improved by avoiding: • lack of regular , scheduled maintenance. • excessive speed. • rapid acceleration. • extended idle. CHECKING YOUR HIGHWAY FUEL ECONOMY USING THE ELECTRONIC MESSAGE CENTER DISPLAY The following procedure will allow you to accurately monitor your actual highway fuel economy . Since t[...]

HAZARD FLASHER For information on the hazard flasher control, refer to Hazar d lights control in the Roadside emergencies chapter . FUEL PUMP SHUT -OFF SWITCH If the engine cranks but does not start after a collision, the fuel pump shut-off switch may have been activated. The shut-off switch is a device intended to stop the electric fuel pump when [...]

Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire. Standard fuse amperage rating and color Fuse rating Color 5 amp T an 7.5 amp Brown 10 amp Red 15 amp Light blue 20 amp Y ellow 20 amp fuse link Light blue 25 amp Natural 30 amp Light [...]

12 3 4 5 78 9 1 0 1 1 17 13 14 15 16 19 20 21 25 26 27 28 29 31 30 36 6 12 18 24 32 33 34 35 37 38 39 40 41 22 23 Roadside emergencies 111[...]

The fuses are coded as follows: Fuse/Relay Location Fuse Amp Rating Description 1 10A Lighting Control Module: Anti-Theft Indicator Lamp, PWM Dimming Output, Illumination Lamps for Microphone, RR and LR Door Ashtrays, Heated Seat Switches, Rear Defrost Control Switch, EA TC Control Panel, Message Center Switches, Speed Control Switches, Cigar Light[...]

Fuse/Relay Location Fuse Amp Rating Description 5 10A V irtual Image Instrument Cluster , Lighting Control Module (LCM RUN/ST ART Sense), Autolamp Light Sensor 6 10A V irtual Image Instrument Cluster , RF Park/T urn Lamp 7 20A Power Point 8 20A Fuel Filler Door Release Switch, T runk Lid Relay 9 10A Air Bag Diagnostic Monitor , EA TC Module, Blower[...]

Fuse/Relay Location Fuse Amp Rating Description 13 15A Lighting Control Module (LCM): RF T urn Lamp, Right T urn Indicator (VIC), RR Side Marker Lamps, T ail Lamps, License Lamps, LR Stop/T urn Lamps, Clock Illumination 14 20A Cigar Lighter 15 10A ABS Evac and Fill Connector 16 30A Moonroof Switch 17 - NOT USED 18 10A Lighting Control Module 19 10A[...]

Fuse/Relay Location Fuse Amp Rating Description 26 10A V irtual Image Instrument Cluster , EA TC Module 27 - NOT USED 28 10A Shift Lock Actuator , V ehicle Dynamic Module, V irtual Image Instrument Cluster , Rear W indow Defrost, Heated Seat Switch Assembly , Low T ire Pressure Module 29 10A Radio 30 10A Heated Mirrors 31 15A Lighting Control Modul[...]

Fuse/Relay Location Fuse Amp Rating Description 34 15A Console Shift Illumination, A/C Clutch Cycling Pressure Switch, A/C Clutch Relay (DTR) Sensor , Intake Manifold Runner Control, Backup Lamps 35 - NOT USED 36 - NOT USED 37 30A Subwoofer Amplifier , Radio 38 10A Analog Clock, CD Player , Mobile T elephone T ransceiver , RESCU 39 10A Power Door L[...]

Power distribution box The power distribution box is located in the engine compartment near the battery . The power distribution box contains high-current fuses that protect your vehicle’ s main electrical systems from overloads. Always disconnect the battery before servicing high current fuses. Always replace the cover to the Power Distribution [...]

The high-current fuses are coded as follows: Fuse/Relay Location Fuse Amp Rating Description 175 Generator/V oltage Regulator 1 30A** Driver’ s Seat Module 2 30A** Passenger’ s Seat Module 3 40A** Ignition Switch 4 40A** Ignition Switch 5 40A** Driver W indow 6 - NOT USED 7 30A** PCM Power 8 40A** Rear W indow Defrost Control 9 60A** I/P Fuse P[...]

Fuse/Relay Location Fuse Amp Rating Description 8 30A* Front Passenger W indow 1 - A/C Diode 2 - PCM Diode * Mini Fuses ** Maxi Fuses CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily . Instead, gradually decrease your speed. Hold the steering wheel firmly and slowly move to a safe place on the side of the road[...]

5. Loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground. Refer to Anti-theft lug nuts for information on removing anti-theft lug nuts. On vehicles equipped with Air Suspension, turn OFF the Air Suspension switch prior to jacking, hoisting or towing your vehicle. Refer to Air suspen[...]

10. Remove the jack and fully tighten the lug nuts in the order shown. 11. Put flat tire, jack and lug wrench away . 12. T urn on the air suspension switch. Anti-theft lug nuts (if equipped) If your vehicle is equipped with this feature, one of the lug nuts on each wheel must be removed and replaced with a special key . The key and registration car[...]

JUMP ST ARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. Do not push start your vehicle. Y ou could damage the catalytic converter . Batteries contain sulfuric acid which burns skin, eyes, and clothing. Preparing your vehicle Also see[...]

Connecting the jumper cables 1. Position the vehicles so that they do not touch one another . 2. Switch off the engine. Switch off any unnecessary electrical equipment. 3. Connect the positive (+) terminal of the discharged battery (1) to the positive (+) terminal of the booster battery (2). 4. Connect one end of the second lead to the negative (-)[...]

Removing the jumper cables 1. Remove the jumper cables in reverse order . T ake the cable off the alternator mounting brace stud (1) first, followed by the cable on the negative (-) booster battery terminal (2). 2. Remove the cable from the positive (+) terminal of the booster battery (3) and then the discharged battery (4). 3. After the disabled v[...]

If you need to have your vehicle towed, contact a professional towing service or , if you are a member , your roadside assistance center . It is recommended that your vehicle be towed with a wheel lift or flatbed equipment. When calling for a tow truck, tell the operator what kind of vehicle you have. A towing manual is available from Ford Motor Co[...]

SER VICE RECOMMENDA TIONS T o help you service your vehicle: • W e highlight do-it-yourself items in the engine compartment for easy location. • W e provide a “Service Guide” which makes tracking routine service easy . If your vehicle requires professional service, your dealership can provide necessary parts and service. Check your “W arr[...]

Do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom of the instrument panel. 2. Go to the front of the vehicle and release the auxiliary latch that is located under the front center of the hood. Lift the [...]

3. Engine coolant reservoir 4. Passenger compartment air filter assembly 5. T ransaxle fluid dipstick 6. Brake fluid reservoir 7. Battery 8. Air filter assembly 9. Engine oil dipstick 10. Engine oil fill cap ENGINE OIL Checking the engine oil Check the engine oil each time you fuel your vehicle. 1. Make sure the vehicle is on level ground. 2. T urn[...]

• If the oil level is between the MIN and MAX marks , the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below the MIN mark, add enough oil to raise the level within the MIN-MAX range. • Oil levels above the MAX mark may cause engine damage. Some oil must be removed from the engine by a service technician. 7. Put the indicator[...]

Use SAE 5W -30 motor oil certified for gasoline engines by the American Petroleum Institute. Do not use supplemental engine oil additives, oil treatments or engine treatments. They are unnecessary and could, under certain conditions, lead to engine damage which is not covered by your warranty . Changing the engine oil and filter Change your engine [...]

Brake fluid is toxic. If you use a brake fluid that is not DOT 3, you will cause permanent damage to your brakes. Do not let the reservoir for the master cylinder run dry . This may cause the brakes to fail. WINDSHIELD WASHER FLUID Checking and adding washer fluid Check the washer fluid whenever you stop for fuel. The reservoir is highlighted with [...]

If the engine coolant has not been checked for a long period of time, the engine coolant reservoir may eventually empty . If this occurs, a LOW ENGINE COOLANT warning illuminate in the message center and you will need to add engine coolant to the coolant reservoir . For more information on engine coolant maintenance, refer to Adding engine coolant [...]

2. When the engine is cool, wrap a thick cloth around the cap. Slowly turn cap counterclockwise. 3. Step back while the pressure releases. 4. When you are sure that all the pressure has been released, turn it counterclockwise and remove it. Use Ford Premium Cooling System Fluid E2FZ-19549–AA (in Canada, Motorcraft CXC-8–B) or an equivalent prem[...]

coolant concentration above 60%. Leave a 50/50 mixture of engine coolant and water in your vehicle year -round in non-extreme climates. CHECKING AND ADDING POWER STEERING FLUID Check the power steering fluid at least twice a year . If adding fluid is necessary , use only MERCON t AT F power steering fluid. 1. Start the engine and let it run until i[...]

Before adding any fluid, make sure the correct type is used . The type of fluid used is normally indicated on the dipstick and/or dipstick handle and also in the Lubricant specifications section in the Capacities and specifications chapter . Do not drive the vehicle if the fluid level is below the hole at the bottom of the dipstick and outside temp[...]

8. If an overfill occurs, excess fluid should be removed by a qualified technician. An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage. If the fluid level is above the crosshatch (hot operating range) area after driving the vehicle for approximately 30 km (20 miles), excess transmission flu[...]

If your battery has a cover/shield, make sure it is reinstalled after the battery is replaced. Because your vehicle’ s engine is electronically controlled by a computer , some control conditions are maintained by power from the battery . When the battery is disconnected or a new battery is installed, the engine must relearn its idle conditions be[...]

CABIN AIR FIL TER The cabin air filter restricts the entry of airborne dust and pollen particles. The filter is located just in front of the windshield under the cowl vent screen on the passenger side of the vehicle. T o replace the filter , perform the following procedure: 1. In order to gain better access to the filter , turn the ignition key to [...]

3. Pull the rubber cowl seal (number 1 in figure) away from the cowl vent screen. Remove the right half of the cowl vent screen (number 2 in figure) by placing your hand underneath the cowl vent screen and lifting straight up to release the four spring clips. 4. Remove the water shield (number 3 in figure) by disengaging the two water shield lockin[...]

Checking the wiper blades If the wiper blades do not wipe properly , clean both the windshield and wiper blades using undiluted windshield wiper solution or a mild detergent. Rinse thoroughly with clean water . T o avoid damaging the blades, do not use fuel, kerosene, paint thinner or other solvents. Changing the wiper blades When replacing wiper b[...]

• do not exceed 90 km/h (55 mph). Drive at a reduced rate of speed, if possible. • avoid excessive hard steering and braking maneuvers, if possible. • stop periodically to allow the tires to cool down. Pressure alert system (if equipped) Each of your SecuriT ires is monitored by a low tire pressure sensor . A warning will appear in the overhe[...]

your SecuriT ire requires service as soon as possible. Refer to Servicing your SecuriT ires . The Pressure Alert System will activate only when the vehicle is moving faster than 15 km/h (10 mph). Servicing your SecuriT ires If you cannot service your SecuriT ire immediately , replace it with your temporary spare as soon as safely possible. Y our te[...]

T readwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire grade 150 would wear one and one-half (1 1/2) times as well on the government course as a tire grade 100. The relative performance of tires depends upon the actu[...]

SER VICING YOUR TIRES Checking the tire pressure • Use an accurate tire pressure gauge. • Check the tire pressure when tires are cold, after the vehicle has been parked for at least one hour or has been driven less than 5 km (3 miles). • Adjust tire pressure to recommended specifications found on the Safety Compliance Certification Label loca[...]

Replacing the tires Replace the tires when the wear band is visible through the tire treads. Failure to follow these precautions may adversely affect the handling of the vehicle and make it easier to lose control and roll over . T ires that are larger or smaller than your vehicle’ s original tires may also affect the accuracy of your speedometer [...]

WHA T YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS Important safety precautions Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire. If you do not use the proper fuel cap, the pressure in the fuel tank can damage the fuel system or cause it to work improperly in a collision. The fuel system [...]

• Be particularly careful if you are taking “Antabuse” or other forms of disulfiram for the treatment of alcoholism. Breathing gasoline vapors or skin contact could cause an adverse reaction. Consult a physician immediately . Choosing the right fuel Use only UNLEADED FUEL. The use of leaded fuel is prohibited by law and could damage your vehi[...]

The American Automobile Manufacturers Association (AAMA) issued a gasoline specification to provide information on high quality fuels that optimize the performance of your vehicle. W e recommend the use of gasolines that meet the AAMA specification if they are available. It should not be necessary to add any aftermarket products to your fuel tank i[...]

EMISSION CONTROL SYSTEM Y our vehicle is equipped with various emission control components and a catalytic converter which will enable your vehicle to comply with applicable exhaust emission standards. T o make sure that the catalytic converter and other emission control components continue to work properly: • Use only unleaded fuel. • A void r[...]

the V ehicle Emission Control Information Decal located on or near the engine. This decal identifies engine displacement and gives some tune up specifications. Please consult your “W arranty Guide” for complete emission warranty information. Readiness for inspection/maintenance (I/M) testing In some localities, it may be a legal requirement to [...]

3. At the back of the headlamp, pull back and up slightly on the two right angle brackets to release the headlamp assembly from the vehicle. 4. Carefully pull the headlamp assembly away from the vehicle to expose the back of the bulb and wiring connector . 5. Disconnect the electrical connector from the bulb by pulling the connector rearward. 6. Re[...]

5. T urn the headlamps on and make sure they work properly . If the headlamp was correctly aligned before you changed the bulb, you should not need to align it again. AIMING THE HEADLAMPS Y our vehicle is equipped with a V ehicle Headlamp Aim Device (VHAD) on each headlamp. Each headlamp may be properly aimed in the vertical (up/down) and the horiz[...]

2. Use a 4mm wrench or socket to turn the horizontal adjusting screw until the “0” mark on the yellow dial lines up with the reference mark on the marker (as shown) when viewed directly from above. T urning the horizontal adjusting screw in the direction of the arrow changes the horizontal aim as shown. V ertical aim adjustment 1. Park the vehi[...]

3. The “U” and “D” on the bubble indicate the directional change (up or down) of the vertical aim. 4 .U s ea4m m wrench or socket to turn the vertical adjusting screw until the bubble is centered between the two red lines which represents the “0” mark position. When the horizontal and vertical indicators are set to the “0” mark, the[...]

Function T rade Number Door mounted lamp (front) 214-2 Illuminated visor mirror 74 Overhead console reading lamp (without moon roof) 912 Passenger assist handle (rear seat) 211-2 T o replace all instrument panel lights - see your dealer . CLEANING AND CARING FOR YOUR VEHICLE Refer to the “Customer Assistance Guide” for a list of Ford-approved c[...]

Repairing paint chips Minor scratches or paint damage from road debris may be repaired with touch-up paint, repair foil or aerosol paint spray from the Ford accessory line. Observe the application instructions on the products. Remove particles such as bird droppings, tree sap, insect remains, tar spots, road salt and industrial fallout immediately [...]

• Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. Cleaning plastic exterior parts Use vinyl cleaner for routine cleaning. Clean with a tar remover if necessary . Do not clean plastic parts with thinners, solvents or petroleum-based cleaners. Cleaning the exterior lamps W ash with the same[...]

Cleaning leather seats For routine cleaning, wipe the surface with a soft, damp cloth. For more thorough cleaning, wipe the surface with a leather and vinyl cleaner or a mild soap. The type of scrubbing pad is very critical because the common 3M “Scotch Brite” green pad is too aggressive and will damage the leather surface. • Spray a small am[...]

Inside windows Use glass cleaner for the inside windows if they become fogged. Cleaning mirrors Do not clean your mirrors with a dry cloth or abrasive materials. Use a soft cloth and mild detergent and water . Be careful when removing ice from outside mirrors because you may damage the reflective surface. Maintenance and care 159[...]

MOT ORCRAFT P ART NUMBERS Component 4.6L DOHC V8 engine Air filter F A-1615 Cabin air filter FP-5 Fuel filter FG-800A Battery BXT -65-750 Oil filter FL-820-S Spark plugs* A WSF-32EE** * Refer to V ehicle Emissions Control Information (VECI) decal for spark plug gap information. **If a spark plug needs to be replaced, use only spark plugs with the s[...]

Fluid Ford Part Name Application Capacity Fuel tank N/A All 75.7L (20.0 gallons) Automatic transaxle Motorcraft MERCON t V AT F All 13.0L (13.7 quarts) W indshield washer fluid Ultra-Clear W indshield W asher Concentrate All Fill to line in reservoir LUBRICANT SPECIFICA TIONS Item Ford Part Name or equivalent Ford Part Number Ford Specification Bra[...]

Item Ford Part Name or equivalent Ford Part Number Ford Specification Engine oil Motorcraft 5W30 Super Premium Motor Oil XO-5W30-QSP WSS-M2C153-G and API Certification Mark Constant velocity joints CV Joint Grease (High T emp.) E43Z-19590-A ESP-M1C207-A Engine coolant Ford Premium Cooling System Fluid E2FZ-19549-AA ESE-M97B44-A Power steering fluid[...]

VEHICLE DIMENSIONS V ehicle dimensions mm (in) (1) Overall length 5 294.7 (208.4) (2) Overall width 1 870.3 (76.3) (3) Overall height 1 421.9 (55.9) (4) Wheelbase 2 769.8 (109.0) (5) T rack - Front 1 600.2 (63.0) (5) T rack - Rear 1 562.1 (61.5) 1 4 Capacities and specifications 163[...]

IDENTIFYING YOUR VEHICLE Safety compliance label The National Highway T raffic Safety Administration Regulations require that a Safety Compliance Certification Label be affixed to a vehicle and prescribe where the Safety Compliance Certification Label may be located. The Safety Compliance Certification Label is located on the front door latch pilla[...]

V ehicle identification number The vehicle identification number is attached to a metal tag and is located on the driver side instrument panel. ENGINE NUMBER The engine number (the last eight numbers of the vehicle identification number) is stamped on the engine block, transmission, frame and transfer case (if so equipped). XXXXXXXXXXXXXXXXX AIR BA[...]

REPORTING SAFETY DEFECTS (U.S. ONL Y) If you believe that your vehicle has a defect that could cause a crash, or could cause injury or death, you should immediately inform the National Highway T raffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company . If NHTSA receives similar complaints, it may open an investigation, and [...]

Air bag supplemental restraint system .......................................... 80 and child safety seats ..............81 description ................................ 80 disposal ...................................... 83 indicator light ........................... 82 passenger air bag ..................... 81 Air suspension description ..........[...]

high beam ................................. 26 Heating ........................................ 27 High beams indicator light ............................. 8 Hood release lever ............................127 Ignition positions of the ignition ........... 34 Jump-starting your vehicle ..... 122, 123 attaching cables ...................... 123 disco[...]

Speed control .............................. 36 canceling a set speed ............... 39 resuming a set speed ............... 39 tap up/tap down .......................38 turning off ................................. 37 Speedometer ............................... 10 Starting your vehicle ............. 90,92 Sunvisor ................................[...]

170[...]

171[...]

172[...]

173[...]

174[...]

175[...]

Recommended fuel Unleaded fuel only - 91 octane (R+M/2) Fuel tank capacity 75.7L (20.0 gallons) Engine oil capacity (with filter change) 5.7L (6.0 quarts). Use Motorcraft 5W30 Super Premium Motor Oil, Ford Specification WSS-M2C153-G Automatic transaxle fluid capacity 13.0L (13.7 quarts). Use Motorcraft Mercon y VA T F (part# XT -5-QM), Ford Specifi[...]