Français dropdown-ico

AIRLESSCO 3000, 3500 manuel d'utilisation

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30

Aller à la page of

Les manuels d’utilisation similaires

Un bon manuel d’utilisation

Les règles imposent au revendeur l'obligation de fournir à l'acheteur, avec des marchandises, le manuel d’utilisation AIRLESSCO 3000, 3500. Le manque du manuel d’utilisation ou les informations incorrectes fournies au consommateur sont à la base d'une plainte pour non-conformité du dispositif avec le contrat. Conformément à la loi, l’inclusion du manuel d’utilisation sous une forme autre que le papier est autorisée, ce qui est souvent utilisé récemment, en incluant la forme graphique ou électronique du manuel AIRLESSCO 3000, 3500 ou les vidéos d'instruction pour les utilisateurs. La condition est son caractère lisible et compréhensible.

Qu'est ce que le manuel d’utilisation?

Le mot vient du latin "Instructio", à savoir organiser. Ainsi, le manuel d’utilisation AIRLESSCO 3000, 3500 décrit les étapes de la procédure. Le but du manuel d’utilisation est d’instruire, de faciliter le démarrage, l'utilisation de l'équipement ou l'exécution des actions spécifiques. Le manuel d’utilisation est une collection d'informations sur l'objet/service, une indice.

Malheureusement, peu d'utilisateurs prennent le temps de lire le manuel d’utilisation, et un bon manuel permet non seulement d’apprendre à connaître un certain nombre de fonctionnalités supplémentaires du dispositif acheté, mais aussi éviter la majorité des défaillances.

Donc, ce qui devrait contenir le manuel parfait?

Tout d'abord, le manuel d’utilisation AIRLESSCO 3000, 3500 devrait contenir:
- informations sur les caractéristiques techniques du dispositif AIRLESSCO 3000, 3500
- nom du fabricant et année de fabrication AIRLESSCO 3000, 3500
- instructions d'utilisation, de réglage et d’entretien de l'équipement AIRLESSCO 3000, 3500
- signes de sécurité et attestations confirmant la conformité avec les normes pertinentes

Pourquoi nous ne lisons pas les manuels d’utilisation?

Habituellement, cela est dû au manque de temps et de certitude quant à la fonctionnalité spécifique de l'équipement acheté. Malheureusement, la connexion et le démarrage AIRLESSCO 3000, 3500 ne suffisent pas. Le manuel d’utilisation contient un certain nombre de lignes directrices concernant les fonctionnalités spécifiques, la sécurité, les méthodes d'entretien (même les moyens qui doivent être utilisés), les défauts possibles AIRLESSCO 3000, 3500 et les moyens de résoudre des problèmes communs lors de l'utilisation. Enfin, le manuel contient les coordonnées du service AIRLESSCO en l'absence de l'efficacité des solutions proposées. Actuellement, les manuels d’utilisation sous la forme d'animations intéressantes et de vidéos pédagogiques qui sont meilleurs que la brochure, sont très populaires. Ce type de manuel permet à l'utilisateur de voir toute la vidéo d'instruction sans sauter les spécifications et les descriptions techniques compliquées AIRLESSCO 3000, 3500, comme c’est le cas pour la version papier.

Pourquoi lire le manuel d’utilisation?

Tout d'abord, il contient la réponse sur la structure, les possibilités du dispositif AIRLESSCO 3000, 3500, l'utilisation de divers accessoires et une gamme d'informations pour profiter pleinement de toutes les fonctionnalités et commodités.

Après un achat réussi de l’équipement/dispositif, prenez un moment pour vous familiariser avec toutes les parties du manuel d'utilisation AIRLESSCO 3000, 3500. À l'heure actuelle, ils sont soigneusement préparés et traduits pour qu'ils soient non seulement compréhensibles pour les utilisateurs, mais pour qu’ils remplissent leur fonction de base de l'information et d’aide.

Table des matières du manuel d’utilisation

  • Page 1

    SER VICE/OPERA TION MANU AL Form No. 001-683 FEB2305 Form No. 001-683 FEB2305[...]

  • Page 2

    T able of Contents INTRODUCTION Sp ra y & St ri pe S pe ci  ca ti on s 1 Safety W arnings 2 GETTING ST ARTED How to Flush 7 Flushing 8 Setting Up 9 Pressure Relief Procedure 10 Daily Maintenance 10 Starting Up 1 1 Striping Operation 12 Striping T ip Guide 13 REP AIRS/MAINTENANCE INSTRUCTIONS Spray Gun Operation 14 Spray Gun T roubleshooting [...]

  • Page 3

    Bef ore oper at ing thi s un it, rea d an d fol low all saf ety warn in gs and ins truc tion s rel ated to the usa ge o f thi s eq uipm ent . RE AD, LE ARN , and FOL LOW th e P ress ure Rel ief Proc ed ure on Page 10 a nd und erst and al l w arni ngs on page s 2 thru 6. IMPORT ANT WARNING !! HANDLE THIS UNIT AS Y OU WOULD A L O ADED FIREARM!! High [...]

  • Page 4

    TIP GUARD AL W A YS have the tip guard in place on the spray gun while spraying. The tip guard alerts you to the injection hazard and helps prevent accidentally placing your ngers or any part of your body close to the spray tip. SPRA Y TIP SAFETY Use extreme caution when cleaning or changing spray tips. If the spray tip clogs while spraying, eng[...]

  • Page 5

    Saf ety War nings Fluids under high pressure from spray or leaks can penetrate the skin and cause extremely serious injury , including the need for amputation. • NEVER point the spray gun at anyone or any part of the body . • NEVER put hands or ngers over the spray tip. Do not use a rag or any other material over your ngers. Paint will pe[...]

  • Page 6

    A VOID COMPONENT RUPTURE This sprayer operates at 2500 psi (170 bar). Always be sure that all components and accessories have a maximum working pressure of at least 3000 psi to avoid rupture which can result in serious bodily injury including injection and property damage. • NEVER leave a pressurized sprayer unattended to avoid accidental operati[...]

  • Page 7

    WHEN ADDING FUEL • T urn engine OFF and let engine cool at least 2 minutes before removing gas cap. • Fill fuel tank outdoors or in well ventilated area. • Do not overll fuel tank. Fill tank to approximately1 inches below top of neck to allow for fuel expansion. • Keep gasoline away from sparks, open ames, pilot lights, heat and ot[...]

  • Page 8

    WHEN TRANSPORTING EQUIPMENT • T ransport with fuel tank EMPTY or with fuel shut-off valve OFF . WHEN STORING GASOLINE OR EQUIPMENT WITH FUEL IN T ANK • Store away from furnaces, stoves, water heaters and other appliances that have pilot lights or other ignition source. They can ignite gasoline vapors. Starting engine creates sparking. Sparking [...]

  • Page 9

    Ho w to F lush FIGURE 1 LOCK TRIGGER TO REMOVE SPRA Y TIP 1. Be sure the gun safety latch is engaged and there is no spray tip in the gun. Refer to Fig. 1. Refer to your separate instruction manual provided with your gun on its safety features and how to engage safety latch. 2. Pour enough clean, compatible solvent (or water when using water -base [...]

  • Page 10

    1. New Sprayer Y our Airlessco unit was factory tested in an antifreeze solution which was left in the pump. Before using oil-base paint,  ush with mineral spirits only . Before using water-base paint ush with soapy water , then do a clean water ush. 2. Changing Colors Flush with a compatible solvent such as mineral spirits or water . 3. C[...]

  • Page 11

    Setting Up to Stripe or Spr ay 1. Connect the hose and gun. a. If the hose is not already installed on the striper , remove the plastic cap plug from the outlet tee at the spray pump, and screw a conductive or grounded 3000 psi airless spray hose onto  uid outlet. b. Connect an airless spray gun to the other end of the hose. c. Do not use steel [...]

  • Page 12

    Pr essur e R elief Pr ocedur e 1. Keep the displacement pump packing nut/wet cup lubricated with Airlessco TSO (Throat Seal Oil) at all times. The TSO helps protect the rod and the packings. 2. Inspect the packing nut daily . Y our pump has a patented T riple Life Packing System. Packing life will be extended a minimum of three times if the followi[...]

  • Page 13

    Star ting Up 1. Lear n ho w to oper ate the control valve. The control valve sets the prime or pressure position as well as the spraying pressure. When the valve is fully counter -clockwise the unit is in the prime position. As the control valve is turned clockwise, the unit’ s output pressure to the gun is gradually increased until the control v[...]

  • Page 14

    Striping Oper a tion 1. Choose handle location The choices are, installing the handle opposite of the single wheel assembly (standard set up) or placing the handle directly over the single wheel assembly . The handle location is really a matter of personal preference, however having the handle away from the single wheel assembly allows for easier l[...]

  • Page 15

    Striping Tip Guide STRIPING TIP REGULAR P AINTING SPRA Y TIP UNIFORM P A TTERN LIGHT HEA VY Striping Tips should not be used for regular spraying. Striping tips are designed for a single pass application, while spray tips are designed for the 1/3 overlap technique used for spray painting. Spray Tip Replacement: During use high pressure will cause t[...]

  • Page 16

    Spr ay Gun Oper a tion Reversible Spray T ip T ip Guard T rigger Guard MAJOR COMPONENTS OF SPRA Y GUN & REVERSIBLE REV -TIP ™ SPRA Y GUN Attach spray gun to airless unit and tighten ttings securely . Set the gun safety latch. (Also may be called gun safety lock, or trigger lock) * The gun safety latch should always be set when the gun is n[...]

  • Page 17

    Spr ay Gun T r oubleshooting DEFECTS CA USE CORRECTION Coarse spray Low pressure Increase the pressure Excessive fogging High pressure Reduce pressure for satisfactory pattern (overspray) Material too thin Use less thinner Pattern too wide Spray angle too lar ge Use smaller spray angle tip Pattern too narrow Spray angle too small Use larger spray a[...]

  • Page 18

    Field T r oubleshooting PROBLEM CAUSE SOLUTION Unit doesn't prime Airleak due to: • Loose Suction Nut • T ighten Suction Nut • W orn O-Rings • Replace O-Ring (106-01 1) on suction seat, & O-Ring (106- 020) below suction seat • Hole in Suction Hose • Replace Suction Hose (331-290) Stuck or Fouled Balls Service outlet valve sucti[...]

  • Page 19

    17 Refer to Figure 1 1. Follow the Pressure Relief Procedure on page 10. 2. Flush the material you are spraying out of the machine. 3. Remove the connecting rod shield (331-11 1). 4. Move the piston rod (331-093) to its lowest position by cycling pump slowly . 5. Remove the retaining ring (331-062) from the connecting rod (331-038) and slide the sl[...]

  • Page 20

    Ser vicing the Piston R od - Outlet V alv e 331-196 331-195 Piston DISASSEMBL Y OF THE OUTLET V AL VE REFER T O FIGURE 3 1. Disconnect the Fluid Pump following instructions on page 17 . 2. Place piston holder (331-195) in a vise. Slide piston into the holder & lock in place with a 3/8” dowel (331-196). 3. Use a 1/4” allen wrench to unscrew [...]

  • Page 21

    P acking R eplacement Pr ocedur es 19 Fluid Pump Remo val - Refer to Figure 1 1. Follow the Pressure Relief Procedure on page 9. 2. Flush material you are spraying out of the machine. 3. Remove the connecting rod shield (331-1 11). 4. Move the piston rod (331-093) to its lowest position by cycling pump slowly . 5. Remove the retaining ring (331-062[...]

  • Page 22

    FIGURE 5 P acking R eplacement Pr ocedur es FIGURE 6 20 3. Push the two bolts (100-318) through the tube spacers (331-074) & screw into the cover assembly (331-234). Using a 1/2” wrench, tighten the two bolts evenly (alternating between them) until you reach 20 ft-lbs. 4. Reassemble lower suction valve assembly by placing the suction seat (33[...]

  • Page 23

    I n s p e c t i o n & R e p l a c e m e n t o f C o n t r o l V a l v e , B a l l & S e a t 1. Use a wrench to unscrew the control valve with ring seal. 2. Make sure that the control valve knob turns freely and that its stem is not worn unevenly , mushroomed or otherwise damaged. 3. Remove TC guide, verify that it is unbroken, clean and not[...]

  • Page 24

    Gear Bo x Assembl y - Par t No . 305-196 22 Part Number Description 100-004 90 Degree Elbow 100-028 Pipe Plug 100-318 HXHD Screw 100-332 Retaining Ring 100-380 Screw 100-381 Screw 100-398 Retaining Ring 1 12-068 Ball Bearing 1 15-019 Hose Connector 1 17-008 Ball Bearing 305-197 Paint Pump Ass’y 305-199 Shaft Pinion 305-287 Machined End Bell 331-0[...]

  • Page 25

    Spr ay Gun Assembl y - Par t No . 305-280 Gun Mount Assembl y - Par t No . 305-275 - 23 Part Number Description 100-01 1 Airless 1/4” x 50’ Hose 1 16-103 Cable Retainer Spring 120-1 15 008 Silver Gun w/o T ip 305-275 Gun Mount Ass’y 305-280 Spray Gun Assembly 561-025 Rev-Tip Male Seal 561-026 Rev- T ip Seal 563-317ST Striping T ip 560-517 Pai[...]

  • Page 26

    Bypass V alv e Assembl y Par t No. 305-264 Part Number Description Qty . 100-040 Hose, Whip 2 1 15-016 Control V alve Seat Ass’y 1 1 15-017 Ball 1 1 15-024 Unloader V alve 1 1 15-028 Stat-O-Seal 1 1 15-031 Guide T .C. 1 188-377 Return T ube 1 305-194 PR Regulator Housing 1 24[...]

  • Page 27

    Suction Assembl y P ar t No. 331-290 Part Number Description Qty . 106-020 T eon O-Ring 1 141-015 Hose Clamp (some models only) 1 331-034 Suction Nut 1 331-035 Suction Elbow 1 331-217 Suction Filter 1 25[...]

  • Page 28

    F r ame Assembl y Par t No . 305-213 Part Number Description Qty . 100-317 Nut 5/16-18 Centerlock 4 100-320 Wing Screw , 3/8 1 100-370 Screw , Hex Cap 2 1 13-031 Spacer , 5/8 x 1.00 2 1 13-032 Axel, 13” 1 1 19-026 Screw Hex Hd 3 136-131 Chain Sash 1 136-133 Key Ring 1 139-053 Handle, Striper 1 140-029 W asher , Flat, 5/16 8 143-028 W asher , Flat[...]

  • Page 29

    REV-GU ARD ™ Part # 560-xxx REV -TIP for Spray Painting 562-xxxST REV -TIP for Striping P O SI -L O C ™ S Y ST EM Snap in centering of tip. No leaks, splashback or mess. S EA L L O CA T I NG HA ND L E T ip handle simplifies installing & aligning the seal. EA SIE ST A SSE MBL Y Fewer parts - Less complicated takes only seconds! I NT ER C HA [...]

  • Page 30

    XTEND-A-POLE SY STEM Tip Extensions - Complete with Pa tente d SPRA Y CLE AN REV -GU ARD TIP EXTENSIONS, “G” THREAD 032-170 6” Long 032-171 12” Long 032-172 18” Long 032-173 24” Long SWIVEL EXTENSION, “G” THREAD 032-184 36” Long EXTENSIONS (BARE POLES) Add T ip Extension or Swivel Extension to create desired length 032-053 24” L[...]