EZQuest DVD Duplication manuel d'utilisation

EZQuest Duplicators King Boa DVD Duplication User's Manual[...]

Copyright and Trademark The information in this manual is subject to change without prior notice and does not represent a commitment on the part of vendor, who assumes no liability or re- sponsibility for any errors that may appear in this manual. This manual contains materials protected under International Copyright Laws. All rights reserved. No p[...]

Buttons and LCD There are four buttons and an LCD on the panel of the copy smart plus. They are described as follows. 1 2 4 3 5 1. It shows all functions and messages. 2. It is used to scroll up through functions or menus. 3. It is used to scroll down through functions or menus. 4. It is used to execute a selected function. 5. It is used to cancel [...]

3. 4. Detect Drives 1. Copy There are 12 functions for you to use. Function 1 is Copy. You can press t to select other functions. l Place a source DVD into DVD-ROM. l Switch to function 1 Copy by pressing s . Place blank DVD disks into the DVD writers, and press ENT to start copying. l When copying comes to an end, the passed DVDs will eject automa[...]

Chapter 5 Functions There are 12 functions: Copy, Test, Test & Copy, Verify, Compare, Prescan, Disc Info, Select Source, Image, Edit Track, Setup and Advanced Setup. Among the 12 functions, Edit Track is designed exclusively for editing a collection of favorite songs from CDs. During operation if you do not understand an LCD message, you can se[...]

When copying is in progress, MB and time will decrease whereas the percentage of completion increase. When copying comes to an end, LCD will show the results as follows. The passed DVDs will eject automatically. 1.Copy OK: 03 5.2 Test Function 2 Test is to simulate the copying progress. When simulation finishes, there will be no data really written[...]

LCD will show the testing information as follows. Testing- DVD 0% 4213.4MB d:20:15 When the test comes to an end, LCD will show the results as follows. 2.Test OK: 03 Stopping the test halfway does not affect the DVD disks, but if the DVD-rewriteable disks contain important data, they may be destroyed. 5.3 Test & Copy Select function 3. Put a so[...]

When the test finishes, actual copying will begin as shown below. Copying- DVD 0% 4213.4MB d:20:15 When the whole process finishes, LCD will show the results as follows. 3.Test & Copy OK: 03 5.4 Verify Function 4 Verify is to examine if the target DVDs can be read correctly after copying. Select function 4. 4.Verify Press ENT to verify. LCD wil[...]

When verification comes to an end, LCD will show the results as follows. 4.Verify OK: 03 5.5 Compare Function 5 Compare is to make a comparison between the source DVD and the target DVDs after copying. Select function 5. Put the source DVD onto DVD-ROM and the target DVDs onto DVD writers. 5.Compare Press ENT to compare.LCD will show the comparison[...]

Press ENT to see the details of source 1 as shown below. Src: 01 DVD-ROM Total: 4213.4MB Press ENT to see the details of source 2. If the comparison is identical, LCD will show the message as follows. Src: 02 DVD-RW Identical If comparison fails, LCD will show the failure. By pressing ENT twice, LCD will show that the contents of source 1 and those[...]

Press ENT to prescan. LCD will show the scanning information as follows. Scaning- DVD 0% 4213.4MB 40:40 When scanning finishes, and the source DVD can be read correctly, LCD will show the results as follows. PreScan OK! 5.7 Disc Info Function 7 Disc Info is to show the basic information of source DVD. Select function 7. Put the source DVD onto DVD-[...]

5.8 Select Source Function 8 Select Source is to let you select the data on DVD-ROM, DVD writers or HDD as the source from which copying will be done. 8.Select Source Select function 8. Press ENT , and then press s t to select the source as shown below. Src: DVD-ROM 01 IDE1 Master After selecting the source such as DVD-ROM, you can press ENT , and [...]

5.9 Image Function 9 Image is valid only when you have installed a hard disk. This function includes 6 parts. They are Load, Delete Image, Image Info, Compare Image, Select Partition and Select Src Drive. The loaded data is called an image file. Select function 9. 9.Image 5.9.1 Load On the above figure press ENT , and you will enter the following f[...]

After the image file is successfully loaded, LCD will show the results as follows. Image load OK If there is an image file existing in the current partition, the system will ask you whether to overwrite it or not. Please use s t to confirm Yes or No. Image Exists Overwrite?Yes 5.9.2 Delete Image If you want to empty an image file stored in a partic[...]

After the image file is deleted, LCD will show the results as follows. Partition A: Image is deleted 5.9.3 Image Info This function is to show the basic information of an image file stored in a particular partition. First, select the function by pressing t . 9-03.Image P: A Image Info Press ENT , and LCD will show the information of the image file [...]

Press ENT , and LCD will show the comparison information as follows. Compare- DVD 0% 4213.4MB 1:05:06 When comparison comes to an end, LCD will show the results as follows. Compare OK: 1 Fail: 0 Diff: 0 Press ENT to see the details of source 1 as shown below. Src: 01 DVD-ROM Total: 4213.4MB Press ENT to see the details of source 2. If the compariso[...]

5.9.5 Select Partition This function is to select a partition in the hard disk. First, select the function by pressing t . 9-05.Image P: A Select Partition After installing a hard disk, your copy smart plus will format it automatically. Each partition will occupy 5GB. The number of partitions is dependent on the hard diskís capacity. The partition[...]

First, select the function by pressing t . 9-06. Image P: A Image Src Drive Then, use s t to select DVD-ROM or any of the DVD writers as the source. Select Img Src: 01 IDE1 DVD-ROM After selecting the source such as DVD-ROM, you can press ENT , and LCD will show the message as follows. Load image from Drive ID-01 5.10 Edit Track (for CD only) Funct[...]

Select function 10. 10. Edit Track 5.10.1 CD to CD On the above figure press ENT , and you will enter the following figure.Here the function CD to CD is to let you select a track or more from CD-ROM, and then copy into blank CD-R/RWs. 10-01. Edit Track CD to CD Edit On the above figure press ENT , and you will enter the following figure. Here 1/10 [...]

After selecting, please use s to move to the ìEndî menu as shown below. Select Track: End 1Trk03:25 Press ENT to finish the CD editing, and use s t to confirm Yes or No. End edit disc and burn?Yes LCD will show the copying information as follows. Copying- 24X Edit 1/10 - > 1/1 On the above figure 1/1 means the first track of all tracks we have[...]

The system will ask if you want to keep editing. Please use s t to confirm Yes or No. as shown below. Continue edit next Disc?Yes If you want to keep editing, the current source CD will eject auctomatically, and the system will ask you to insert another new CD as shown below. Insert next disc After inserting the new CD, press ENT to edit as before.[...]

Press ENT to finish the CD editing, and use s t to confirm Yes or No. End edit disc and burn?Yes LCD will show the copying information as follows. Copying- 24X Edit 2/10 - > 2/2 On the above figure 2/2 means the second track of all tracks we have selected, and so far we have selected two tracks from two different CDs. When copying comes to an en[...]

On the above figure Press ENT . The system will ask if you want to close all CDsí sessions. Please use s t to confirm Yes or No as shown below. Close all discís session? Yes After deciding to close, LCD will show the message as follows. Closing Session Please wait--- 5.10.2 CD to HDD After closing sessions, press ESC and t to enter the following [...]

Suppose we decide to select the first track, then press ENT . A ì+î will appear beside 1/10 as shown below. But pressing ENT again may cancel the selection. Select Track: +1/10 03:25 After selecting, please use s to move to the ìEndî menu as shown below. Select Track: End 1Trk03:25 End edit disc and burn?Yes Then, the track as an image file wil[...]

The system will ask if you want to keep editing. Please use s t to confirm Yes or No. as shown below. Continue edit next Disc?Yes If you want to keep editing, the current source CD will eject auctomatically, and the system will ask you to insert another new CD as shown below. Insert next disc After inserting the new CD, press ENT to edit as before.[...]

Then, the track as an image file will be loaded into HDD. LCD will show the loading information as follows. Load- P0 -24X Edit 2/10 - > 2/2 When loading comes to an end , LCD will show the message as follows. Image load OK The system will ask if you want to keep editing. This time please use t to confirm No as shown below. Continue edit next Dis[...]

When burning finishes , LCD will show the results as follows. Burn Complete ! OK: 03 On the above figure press ESC to enter the following figure. Now press t to move the data from HDD template into a certain partition. Burn or Move to partition? Move After pressing t , you need to select a partition into which the data will be moved. Suppose we sel[...]

If the chosen partition has contained image data, the system will ask to overwrite or keep the data. Here please use s to overwrite. Image Exists Overwrite?Yes After pressing s , LCD will show the moving information as follows. Moving to P: A 0% When moving finishes, LCD will show the results as follows. Moving to P: A OK! 5.10.3 Play Audio Track T[...]

Use s t to select the track you want to play. Select Track: 1/10 03:25 After selecting and pressing ENT , LCD will show the playing information below. Playing Track-1 00:00 / 03:25 5.10.4 Close Session This function is to close CDs and let no data written into. After closing, you can put the CDs on any normal player and listen. On the above figure [...]

After pressing ENT , LCD will show the message as follows. Closing Session Please wait--- When closing finishes, LCD will show the results as follows. Closing Complete OK :3 Fail :0 5.11 Setup Function 11 Setup lets you change the default settings. Once you change a setting, remember to press ENT to save it. However, it is suggested to use the defa[...]

5.11.1 Language On the above figure press ENT , and you will enter the following figure. The function Language lets you select a language in which messages can be shown on LCD. 11-01. Setup Language Press ENT to enter the following figure. Here LCD only supports English. Language English 5.11.2 Burn Speed On the above figure press ESC and t to ente[...]

5.11.3 Read Speed On the above figure press ESC and t to enter the following figure. The function Read Speed lets you control the reading speed of target DVDs. 11-03. Setup Read Speed Press ENT to enter the following figure. The default is maximum, but there are still other choices: 32X, 16X and 8X. Read Speed Maximum 5.11.4 Auto Start Drive On the[...]

5.11.5 Startup Menu On the above figure press ESC and t to enter the following figure. Startup Menu lets you select any one of the functions except Adv Setup as the first item appearing on the menu whenever you turn on the copy smart plus. 11-05. Setup Startup Menu Press ENT to enter the following figure. The default is Copy. Of course you can sele[...]

5.11.7 Auto Compare On the above figure press ESC and t to enter the following figure. Auto Compare is to compare automatically the source DVD and the target DVDs after copying. 11-07. Setup Auto Compare Press ENT to enter the following figure. The default is Off. Press t to select On. Auto Compare Off 5.11.8 Auto Prescan On the above figure press [...]

5.11.9 Eject Disc On the above figure press ESC and t to enter the following figure. Eject Disc provides three choices. They are Eject Good Only, Eject All Disc, and Do Not Eject. Eject Good Only means that the DVDs will eject automatically only when they are copied successfully. Eject All Disc means that the DVDs will eject automatically whether t[...]

Press ENT to enter the following figure. The default is On. Press t to select Off. Burn On The Fly On If your copy smart plus doesnít connect with a hard disk, LCD will show the message as follows. No Valid HDD ! 5.11.11 Burn Mode On the above figure press ESC to return to Function 11, and then select part 11 Burn Mode as the following figure show[...]

5.11.12 Button Sound On the above figure press ESC and t to enter the following figure. Button Sound lets you control the sound of a button when you press it. 11-12. Setup Button Sound Press ENT to enter the next figure. The default is On. Press t to select Off. Button Sound On 5.11.13 Device Info On the above figure press ESC and t to enter the fo[...]

Press ENT to enter the next figure. DVD-ROM DVD-116 1.22 Press t twice to enter the next figure. 02 IDE2 Master DVD-RW : PIONEER Press ENT to enter the next figure. DVD-RW DVR-103 1.80 5.11.14 System Info On the above figure press ESC and t to enter the following figure. System Info shows the information of the system. 11-14. Setup System Info Pres[...]

5.12 Adv Setup On the above figure press ESC to return to Function 11. Then, press ESC for 2 seconds to enter Function 12 as the following figure shows. Function 12 Adv Setup lets you change the system configuration. This function includes 13 parts. They are UnderRun Protect, Overburn, Read Error Skip, Format HDD, Verify HDD, Burn-in, Update Firmwa[...]

5.12.2 Overburn On the above figure press ESC and t to enter the following figure. Overburn lets you decide whether to copy beyond the limit of the CD or not. 12-02. Adv Setup Overburn Press ENT to enter the following figure. The default is Off. Press t to select On. Overburn Off 5.12.3 Read Error Skip On the above figure press ESC and t to enter t[...]

5.12.4 Format HDD On the above figure press ESC and t to enter the following figure. Format HDD is to partition the hard disk. But before formatting, all data on the hard disk will be deleted. 12-04. Adv Setup Format HDD Press ENT to enter the next figure. Use s t to confirm Yes or No. All data will be lost, format? Yes If your copy smart plus does[...]

Press ENT to enter the next figure. Use s t to confirm Disk or Parti. Verify Disk or Partition? Disk Press ENT to verify. After verification LCD will show the results as follows. Verify Hard Disk OK! 5.12.6 Burn-in On the above figure press ESC and t to enter the following figure. Burn-in is to simulate the copying progress many times. The time can[...]

Press ENT and use s t to select the time of simulation such as 1, 2, 3...1000 or Run Continuous. The figure below shows Run Continuous. Sel burn-in num: Run Continuous Press ESC , ENT , t to select Erase & Copy as the following figure shows. Erase & Copy is to erase and write repeatedly. It is only for DVD rewriteable disks. Burn-in Erase&a[...]

You can get the newest firmware version from ACARD by e-mail, or download it directly from the web site: http://www.acard.com Then, unzip the file ìcdxxx.binî and copy it into a blank DVD. After placing the DVD on the DVD-ROM , press ENT . The system will begin searching the new firmware and show the message on LCD as follows after it finds the n[...]

Press ENT to enter the next figure. Follow the instructions on LCD to do the button test. After that, the system will do the self-test of SDRAM, the hardware connection test and flash test. All test results will be shown on LCD. It is the easiest way to know if the system can work well. When the whole process finishes, LCD will show the message as [...]

When default loading finishes, LCD will show the results as follows. Load Default OK 5.12.11 CD+G On the above figure press ESC and t to enter the following figure. CD+G is a kind of special copying format. This function supports the special format. 12-11. Adv Setup CD+G Press ENT to enter the next figure. The default is Off. Press t to select On. [...]

Troubleshooting 6.1 About LCD After powering on if there is no LCD, please check if the connection of power cord is frim and the environment of power outlet is normal. 6.2 About Error Messages During Copy, Test, Compare and Verify, etc. if you press ESC to abort, an error message will appear on LCD. Abortion may cause the copy smart plus to hang up[...]

6.4 About Buttons If you press any one of the four buttons on the panel, but there is no response, it is perhaps that the button cannot function well. Please inspect the jumper setting. 6.5 About DVD Writer Not Readable After copying if the DVD writer is not readable, please use Compare to examine, or get another DVD-ROM to test. 6.6 About High Fai[...]

6.8 About Function 12 and Cancellation If you want to execute function 12 Advanced Setup, you can press ESC for 2 seconds. And during operation if you want to cancel a function like Copy, Test, Verify and so on, you can press ESC for 2 seconds, too. Page 49[...]

Appendix 1 List of Functions 1 Copy 2 Test 3 Test & Copy 4 Verify 5 Compare 6 Prescan 7 Disc Info 8 Select Source 9 Image (It works only when a hard disk is connected) 9.1 Load 9.2 Delete Image 9.3 Image Info 9.4 Compare Image 9.5 Select Partition (Each partition is 5GB) 9.6 Select Src Drive 10 Edit Track (for CD only) 10.1 CD to CD 10.2 CD to [...]

11.10 Burn On The Fly (Default is On) 11.11 Burn Mode (Default is DAO) 11.12 Button Sound (Default is On) 11.13 Device Info 11.14 System Info 11.15 Quick Erase 11.16 Quick Erase 12 Adv Setup 12.1 UnderRun Protect (Default is On) 12.2 Overburn (Default is Off) 12.3 Read Error Skip (Default is Off) 12.4 Format HDD 12.5 Verify HDD 12.6 Burn-in 12.7 Up[...]

Appendix 2 LCD Messages 1. Normal Conditions: Initialize SDRAM ............................................Initialize the memory of the system. Detect Drives ..............................Detect what drives are connected with the system. User Abort! .............................................................Cancel the job during operation. Analyz[...]

Press a Key to Eject Good Disc ... Press any ket to eject the good disc after copying Press a Key to Eject Fail Disc ......Press any key to eject the failed disc after copying. DVD-RW does not Support the Func .......... DVD-RW doesnít support this function. Hold ESC to exit ................................. Press ESC for a second to terminate the[...]

Verify Hard Disk OK! ................................... The hard disk is verified successfully. Verify Hard Disk Fail! ............................ The hard disk is not verified successfully. Verify Partition Header! .................................................. Verify the partition header. Select HD First! ...................................[...]

Check Sum Error!. ................................................. The udpated firmware has errors. Source canít be Hard Disk! .......During comparison the source cannot be hard disk. Last update F/W OK! ................................... The firmware is updated successfully. Last update F/W Fail! .............................. The firmware is n[...]