Heat & Glo LifeStyle 7000XLT manuel d'utilisation

1 - Do not store or use gasoline or other flam- mable vapors and liquids in the vicinity of this or any other appliance. - What to do if you smell gas  Do not try to light any appliance.  Do not touch any electrical switch.  Do not use any phone in your building.  Immediately call your gas supplier from a neighbor's phone. Follow t[...]

2 These units MUST use one of the vent systems described in the Installing the Fireplace section of the Installers Guide . NO OTHER vent systems or components MA Y BE USED . This gas fireplace and vent assembly MUST be vented directly to the outside and MUST NEVER be attached to a chimney serving a separate solid fuel burning appliance. Each gas ap[...]

3 TABLE OF CONTENTS Safety and W arning Information ................................................ 2 Service Parts Lists ..................................................................... 4 Section 1: Approvals and Codes ............................................... 8 Approval Listings and Codes ..............................................[...]

4 2 12 4 8 10 5 15 13 6 14 19 18 17 16 3 1 11 20 7 9 7000XL T (NG , LP) Exploded Part s Diagram / 7000XL T (GN, PL) V ue éclatée des pièces * Part number list on following page. * La liste des numéros de pièce se trouve à la page suivante. Service P arts[...]

5 7000XL T (NG , LP) Service Parts List / 7000XL T (GN, PL) Liste des pièces de rechange IT E M / PI ÈCE ST A NDING PI LO T I G NI TI O N / A LL UMA G E UNE VEI LLEUSE S E R IAL # / N° DE SÉRIE P A RT NUM BER / N° DE PI ÈCE Robert shaw V alv e V al v e N G / V alv e G N 060- 522 V al v e LP / V al v e P L 060- 523 Pi l ot Assem bl y N G / Mod[...]

6 4 * Part number list on following page. * La liste des numéros de pièce se trouve à la page suivante. 1 2 7 8 6 9 14 13 12 3 10 11 5 6000XL TB (NG , LP) Exploded Parts Diagram / 6000XL TB (GN, PL) Vue éclatée des pièces Service P arts[...]

7 6000XL TB (NG , LP) Service Part s List / 6000XL TB (GN, PL) Liste des pièces de rechange ITE M / PI ÈCE ST ANDI NG PI LO T I G NI TI O N / A LLUM A G E UNE VEI LLEUSE SERI A L # / N ° DE SÉRIE P A RT NUM BER / N° DE PI ÈCE 1 V al v e A ssem bly N G / M o du le de V al v e GN 389- 005A 1 V al v e A ssem bly LP / Modu l e de V alv e PL 389- [...]

8 Appliance Certification The Heat-N-Glo fireplace models discussed in this Installers Guide have been tested to certification standards and listed by the applicable laboratories. Certification MODELS: 7000XL T , 6000XL TB LABORA T OR Y : Underwriters Laboratories TYPE: Direct V ent Gas Fireplace Heaters ST ANDARD: ANSI Z21.88CSA2.33 Installatio[...]

9 2 Getting St arted Introducing the Heat-N-Glo Gas Fireplaces Heat-N-Glo direct vent gas fireplaces are designed to oper- ate with all combustion air siphoned from outside of the building and all exhaust gases expelled to the outside. The information contained in this Installers Guide , unless noted otherwise, applies to all models and gas control[...]

10 Figure 1. Diagram of the 7000XL T and 6000XL T B TOP VENT CO LL ARS GAS LINE ACCESS ELECT RICA L ACCE SS GAS CON TRO LS RA TING PLA TE AND LABELS TRIM DOOR HOOD T OP ST ANDOFFS[...]

11 3 Inst alling the Fireplace Step 1. Locating the Fireplace The diagram below shows space and clearance require- ments for locating a fireplace within a room. ABCD E 42 22 36 51 72 Minimum Clearances from the Fireplace to Combustible Materials Inches mm Glass Front ........................ 3 6 .................... 91 4 Floor ......[...]

12 A . ............. 4 2  B . ....... 38 1/2 C . ............. 2 2  D . ............. 4 2  Figure 3. Framing Dimensions Framing should be constructed of 2 X 4 lumber or heavier . Shows center of 12 x 12 vent framing hole for top and rear venting. The center of the hole is one inch (25.4mm) above the center of the horizontal vent p[...]

13 Figure 4. D-Series Direct V ent Component Specifications (5-inch inner pipe / 8 5/8-inch outer pipe) NOTE: PIPES OVERLAP 1-3/8 INCHES (34.93mm) A T EACH JOINT . D V - 3 6 D 5 3/4” (146mm) 8 3/4” (222mm) 11 3 / 4” (298mm) DV - 12D DV - 09 D DV - 06 D D V - 4 8 D D V - 9 0 D 7 3 / 8 ” ( 1 8 7 m m ) 6 5 / 3 2 ” ( 1 5 6 m m ) 1 1 5 / 8 ”[...]

14 Figure 6. Straight Up V ertical V enting Figure 5. V ent System Components and T ermination Kit s Step 3. Inst alling the V ent System A. V ent System Approvals These models are approved to use D-series direct vent pipe components and terminations (see Figures 4 and 5). Approved vent system components are labeled for identification. This pipe is[...]

15 VENTING WITH ONE (1) 90° ELBOW V (F T .) H (F T .) 1' MIN. (305mm) 5' MAX. (1.52m) 2' MIN. (610mm) 10' MAX. (3.1m) 3' MIN. (914mm) 15' MAX. (4.65m) 4' MIN. (1.22m) 20' MAX. (6.2m) V+H= 40 MAX. (12.4MM) 20' MAX. (6.2m) Figure 7. V enting with One 90° Elbow NOTE: IF A 90 o ELBOW IS FIRST A T - T AC[...]

16 VENTING WITH TWO (2) 90 o ELBOWS V FT . H + H 1 (FT .) 1' MIN. (305mm) 5 ´ MAX. (1.52m ) 2' MIN. (610mm) 10´ MAX. (3.1m ) 3' MIN. (914mm) 15´ MAX. (4.65m ) 4' MIN. (1.22m) 20´ MAX. (6.2m ) V+H+H 1 = 40' MAX.(12.4m) 20´ MAX. (6.2 m) V+V 1 +H = 40' MAX.(12.4m) Figure 8. V enting with T wo 90° Elbows[...]

17 VENTING WITH THREE (3) 90° ELBOWS V (FT .) H (FT . ) 1' MIN. (305mm) 5' MAX. (1.52m) 2' MIN. (610mm) 10' MAX. (3.1m) 3' MIN. (914mm) 15' MAX. (4.65m) 4' MIN. (1.22m) 20' MAX. (6.2m) NOTE: H + H 1 = 20' MAX. (6.2m) V + V 1 + H + H 1 = 40' MAX. (12.4m) VENTING WITH THREE (3) 90° ELBOWS V (FT .) H[...]

18 B. Inst alling V ent Component s 1. A t t ach the First V ent Component to the Starting Collars T o attach the first vent component to the starting collars of the fireplace:  Apply a 3/8 inch (9.5mm) bead of stove cement around the 5 inch (127mm) fireplace starting collar .  Make sure that the fireplace rope gasket supplied with the firepl[...]

19 2. Continue Adding V ent Component s W ARNING: INST ALLA TION OF THE 7000XL T FIREPLACE REQUIRES THE USE OF HEA T SHIELD 570-290 ABOVE THE FIRST 90 0 ELBOW IN THE VENTING SYSTEM. (HEA T SHIELD NOT RE- QUIRED FOR 6000XL TB). Figure 1 1 T o Inst all the Heat Shield: 1. Determine if the heat shield is required. Do so by mea- suring the vertical dis[...]

20 For V ertical Runs - The vent system must be supported every eight (8) feet (2.4m) above the fireplace flue outlet by wall brackets. T o install support bracket s for vertical runs:  Attach wall brackets to the vent pipe and secure the wall bracket to the framing members with nails or screws. Figure 14. Installing Support Brackets 4. Install [...]

21 For V ertical Runs - One ceiling firestop is REQUIRED at the hole in each ceiling through which the vent passes. T o install firestops for vertical runs that pass through ceilings:  Position a plumb bob directly over the center of the verti- cal vent component.  Mark the ceiling to establish the centerpoint of the vent.  Drill a hole or[...]

22 ! C. V ent T ermination For Horizont al T erminations - T o attach and secure the termination to the last section of horizontal vent:  Rotate and interlock the ends as described at the begin- ning of the Installing V ent Components section.  The termination kit should pass through the wall firestops from the exterior of the building.  A[...]

23 V =VENT TERMINAL X =AIR SUPPL Y INLET =AREA WHERE TERMINAL IS NOT PERMITTED * 30 minimum for vinyl clad soffits. * * a vent shall not terminate directly above a sidewalk or paved driveway which is located between two single family dwellings and serves both dwellings. *** only permitted if veranda, porch, deck or balcony is fully open on a min[...]

24 For V ertical T erminations - T o locate the vent and install the vent sections:  Locate and mark the vent centerpoint on the underside of the roof, and drive a nail through the centerpoint.  Make the outline of the roof hole around the centerpoint nail.  The size of the roof hole framing dimensions depend on the pitch of the roof. Ther[...]

25 Step 4. Positioning, Leveling, and Securing the Fireplace  Place the fireplace into position.  Level the fireplace from side to side and from front to back.  Shim the fireplace with non-combustible material, such as sheet metal, as necessary .  Secure the fireplace to the framing by nailing or screwing. ! ! The diagram below shows ho[...]

26 Figure 25. Gas Supply Line  Insert insulation from the outside of the fireplace and pack the insulation tightly to totally seal between the pipe and the outer casing.  At the gas line access hole the gap between the supply piping and gas access hole can be plugged with non- combustible insulation to prevent cold air infiltration. Step 6. T[...]

27 Step 8. Wiring the Fireplace NOTE: Electrical wiring must be installed by a licensed electrician. CAUTION: DISCONNECT REMOTE CONTROLS IF AB- SENT FOR EXTENDED TIME PERIODS. THIS WILL PRE- VENT ACCIDENT AL FIREPLACE OPERA TION. For Standing Pilot Ignition Wiring Appliance Requirements  This appliance DOES NOT require 1 10-120 V AC to operate. [...]

28 Step 9. Finishing Figure 28 shows the minimum vertical and corresponding maximum horizontal dimensions of fireplace mantels or other combustible projections above the top front edge of the fireplace. See Figures 2 and 3 for other fireplace clearances. Only non-combustible materials may be used to cover the black fireplace front. W ARNING: WHEN F[...]

29 Inst alling the T rim Combustible materials may be brought up to the specified clearances on the side and top front edges of the fireplace, but MUST NEVER overlap onto the front face. The joints between the finished wall and the fireplace top and sides can only be sealed with a 300° F . (149° C) minimum sealant. W ARNING: WHEN FINISHING THE FI[...]

30 Step 1 1. Before Lighting the Fireplace Before lighting the fireplace, be sure to do the following: Remove all paperwork from underneath the fireplace. Review safety warnings and cautions  Read the Safety and Warning Information section at the beginning of this Installers Guide . Double-check for gas leaks  Before lighting the fireplace, d[...]

31 4 Maint aining and Servicing Y our Fireplace Fireplace Maintenance Although the frequency of your fireplace servicing and main- tenance will depend on use and the type of installation, you should have a qualified service technician perform an appli- ance check-up at the beginning of each heating season. See the table below for specific guideline[...]