Jeep Grand Cherokee (2010) manuel d'utilisation

Cherokee O W N E R ’ S M A N U A L 2 0 1 0 Grand I n f o r m a t i o n P r o v i d e d b y :[...]

T ABLE OF CONTENTS SECTION P AGE 1 INTRODUCTION ............................................................ 3 2 THINGS TO KNOW BEFORE ST AR TING YOUR VEHICLE ............................. 1 1 3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE ............................. 7 5 4 UNDERST ANDING YOUR INSTRUMENT P ANEL .................................. 1[...]

I n f o r m a t i o n P r o v i d e d b y :[...]

INTRODUCTION CONTENTS 䡵 Intr oduction ........................... 4 䡵 Rollover W arning ....................... 5 䡵 How T o Use This Manual .................. 6 䡵 W arnings And Cautions ................... 8 䡵 V ehicle Identification Number .............. 8 䡵 V ehicle Modifications/Alterations ............ 9 1 I n f o r m a t i o n P r [...]

INTRODUCTION Congratulations on selecting your new Chrysler Group LLC vehicle. Be assured that it r epresents pr ecision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This is a specialized utility vehicle designed for both on-road and off-road use. It can go places and perform tasks for wh[...]

This Owner’s Manual has been prepar ed with the assis- tance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle. It is supplemented by a W arranty Information Booklet, located on the DVD, and various customer-oriented documents. Please take the time to read these publica- tions carefully . Fo[...]

Failure to use driver and passenger seat belts provided is a major cause of severe or fatal injury . In fact, the U.S. government notes that the universal use of existing seat belts could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries by two million annually . In a rollover crash, an unbelted person is si[...]

1 INTRODUCTION 7 I n f o r m a t i o n P r o v i d e d b y :[...]

W ARNINGS AND CAUTIONS This Owner’s Manual contains W ARNINGS against op- erating procedures that could result in an accident or bodily injury . It also contains CAUTIONS against proce- dures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important information. Observe all W arnings and Cautions. [...]

VEHICLE MODIFICA TIONS/AL TERA TIONS W ARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death. 1 INTRODUCTION 9 I n f o r m a t i o n P r o v i d e d b y :[...]

I n f o r m a t i o n P r o v i d e d b y :[...]

THINGS TO KNOW BEFORE ST ARTING YOUR VEHICLE CONTENTS 䡵 A W ord About Y our Keys ................. 1 4 ▫ W ir eless Ignition Node (WIN) ............ 1 4 ▫ K e y F O B ........................... 1 5 ▫ Removing Key FOB From Ignition ......... 1 5 ▫ Key-In-Ignition Reminder ............... 1 7 䡵 Sentry Key 威 .......................... 1[...]

▫ Remote Open W indow Feature — If Equipped ........................... 2 3 ▫ Using The Panic Alarm ................. 2 3 ▫ Programming Additional T ransmitters ...... 2 3 ▫ T ransmitter Battery Replacement .......... 2 4 ▫ General Information ................... 2 5 䡵 Remote Starting System — If Equipped ....... 2 5 ▫ How T o Use[...]

▫ Seat Belts And Pregnant W omen .......... 4 5 ▫ Seat Belt Extender ..................... 4 5 ▫ Supplemental Restraint Systems (SRS) — Airbags ............................ 4 6 ▫ Advanced Front Airbag Features .......... 4 8 ▫ Airbag Deployment Sensors And Controls . . . 52 ▫ Event Data Recorder (EDR) .............. 5 9 ▫ Child Rest[...]

A WORD ABOUT YOUR KEYS Y our vehicle uses a keyless ignition system. This system consists of a Key Fob with Remote Keyless Entry (RKE) transmitter and a W ireless Ignition Node (WIN) with integral ignition switch. Y ou can insert the Key Fob into the ignition switch with either side up. Wireless Ignition Node (WIN) The W ireless Ignition Node (WIN)[...]

Key Fob The Key Fob operates the ignition switch. It also contains the Remote Keyless Entry (RKE) transmitter and an emergency key , which stores in the rear of the Key Fob. The emergency key allows for entry into the vehicle should the battery in the vehicle or the RKE transmitter go dead. The emergency key is also for locking the glove box. Y ou [...]

NOTE: • If you try to remove the Key Fob before you place the shift lever in P ARK, it may become trapped tempo- rarily in the ignition switch. If this occurs, rotate the key to the right slightly , then remove the Key Fob as described. If a malfunction occurs, the system will trap the key in the ignition switch to warn you that this safety featu[...]

Key-In-Ignition Reminder Opening the driver’s door when the Key Fob is in the ignition and the ignition switch position is OFF or ACC, sounds a signal to remind you to remove the Key Fob. NOTE: The Key-In-Ignition reminder only sounds when the Key Fob is placed in the OFF or ACC ignition position. SENTR Y KEY 姞 The Sentry Key 威 Immobilizer sy[...]

NOTE: The Sentry Key 威 Immobilizer system is not compatible with aftermarket remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection. All of the Key Fobs provided with your new vehicle have been programmed to the vehicle electronics. Replacement Keys NOTE: Only Key Fobs that are progra[...]

• This device may not cause harmful interference. • This device must accept any interference that may be received, including interference that may cause undes- ired operation. VEHICLE SECURITY ALARM — IF EQUIPPED This V ehicle Security Alarm monitors the vehicle doors, liftgate, liftgate flipper glass, and ignition for unautho- rized operatio[...]

cancel the arming. If the V ehicle Security Alarm success- fully arms, the V ehicle Security Light will flash at a slower rate to indicate the alarm is set. T o Disarm the System T o disarm the V ehicle Security Alarm, you will need to press the UNLOCK button on the RKE transmitter or turn the ignition key to the ON position. If something has trigg[...]

NOTE: Inserting the Key Fob with RKE transmitter into the ignition switch disables all buttons on that RKE transmitter; however , the buttons on the remaining RKE transmitters will continue to work. Driving at speeds 5 mph (8 km/h) and above disables all RKE transmitter buttons for all RKE transmitters. T o Unlock the Doors Press and release the UN[...]

Flash Lamps with Remote Key Lock This feature will cause the turn signal lamps to flash when the doors are locked or unlocked with the RKE transmitter . This feature can be turned on or off. T o change the current setting, proceed as follows: • For vehicles equipped with the Electronic V ehicle Information Center (EVIC), refer to “Electronic V [...]

T o Release the Liftgate Flipper Glass Press the FLIPPER GLASS/LIFTGA TE RELEASE button two times (the second press within five seconds of the first press) to open liftgate flipper glass. W ARNING! Driving with the flipper glass open can allow poi- sonous exhaust gases into your vehicle. Y ou and your passengers could be injured by these fumes. Kee[...]

T ransmitter Battery Replacement The recommended replacement battery is one CR2032 battery . NOTE: • Perchlorate Material — special handling may apply . See www .dtsc.ca.gov/hazar douswaste/perchlorate • Do not touch the battery terminals that are on the back housing or the printed circuit board. 1. Battery access is through a door located on[...]

3. Reposition the access door panel over the battery opening and snap into place. General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference received, includin[...]

How to Use Remote Start All of the following conditions must be met before the engine will remote start: • Shift lever in P ARK • Doors closed • Hood closed • Liftgate closed • Hazard switch off • Brake switch inactive (brake pedal not pressed) • Ignition key removed from ignition switch • Battery at an acceptable charge level • R[...]

NOTE: • If an engine fault is present the vehicle will start and then shut down 10 seconds later . • The park lamps will turn on and remain on during Remote Start mode. • For security , power window and power sunroof op- eration (if equipped) are disabled when the vehicle is in the Remote Start mode. • The engine can be started two consecut[...]

DOOR LOCKS Manual Door Locks Use the manual door lock plunger to lock the doors from inside the vehicle. If the plunger is down when the door is closed, the door will lock. Therefor e, make sur e the key is not inside the vehicle before closing the door . W ARNING! • For personal security and safety in the event of an accident, lock the vehicle d[...]

If you press the door lock switch while the Key Fob is in the ignition switch and the driver’s door is open, the doors will not lock. The rear doors cannot be opened from inside the vehicle until you pull up the lock plungers. Automatic Unlock On Exit Feature — If Equipped If Auto Unlock is enabled, this feature will unlock all the doors when t[...]

WINDOWS Power Windows The power window controls are located on the driver’s door trim panel. There is a single switch on the front passenger door/rear doors which operates the front passenger/rear passenger door windows. The window controls will operate only when the ignition switch is in the ON or ACCESSOR Y position. The power window switches r[...]

Auto-Down Both the driver and front passenger window switches have an “Auto-Down” feature. Press the window switch past the first detent, release, and the window will go down automatically . T o cancel the “Auto-Down” move- ment, operate the switch in either the up or down direction and release the switch. T o open the window part way , pre[...]

Resetting the Auto Up Feature Should the Auto Up feature stop working, the window probably needs to be reset. T o reset Auto Up: Pull the window switch up and close the window com- pletely , then pull and hold the switch for one second. W indow Lockout Button The W indow Lockout button on the driver’s door allows you to disable the window control[...]

Wind Buffeting W ind buffeting can be described as the perception of pressur e on the ears or a helicopter-type sound in the ears. Y our vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occur- rence and can be minimized. If the buffeting occurs with [...]

Liftgate Flipper Glass The liftgate flipper glass is also unlocked when the liftgate is unlocked. T o open the flipper glass, push up on the window switch located on the liftgate. W ARNING! T o avoid injury , stand back when opening. Glass may automatically rise. Once the liftgate flipper glass has been opened, connec- tion to the rear window wiper[...]

W ARNING! Driving with the flipper glass open can allow poi- sonous exhaust gases into your vehicle. Y ou and your passengers could be injured by these fumes. Keep the flipper glass closed when you are operating the vehicle. OCCUP ANT RESTRAINTS Some of the most important safety features in your vehicle are the restraint systems: • Three-point la[...]

Please pay close attention to the information in this section. It tells you how to use your restraint system properly , to keep you and your passengers as safe as possible. W ARNING! In a collision, you and your passengers can suffer much greater injuries if you are not properly buckled up. Y ou can strike the interior of your vehicle or other pass[...]

W ARNING! • W earing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body . These are the strongest parts of your body and can take the forces of a collision the best. W earing your belt in the wrong place could make your injuries in a collision much worse. Y ou might suffer internal injuries, or[...]

2. The seat belt latch plate is above the back of your seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to make the belt go around your lap. 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” Latch Plate Latch Plate to Buckle 38 THIN[...]

W ARNING! • A belt that is buckled into the wrong buckle will not protect you properly . The lap portion could ride too high on your body , possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well. In a sudden stop you could move too far forward, increasing [...]

4. Position the lap belt across your thighs, below your abdomen. T o remove slack in the lap portion, pull up a bit on the shoulder belt. T o loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision. W ARNING! • A lap belt worn too high can increas[...]

W ARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically , checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately . Do not disassemble or modify the system. Seat belt assemblies must be replaced after an accident if they have been damaged (ben[...]

Energy Management Feature This vehicle has a safety belt system with an Energy Management featur e in the front seating positions to help further reduce the risk of injury in the event of a head-on collision. This safety belt system has a retractor assembly that is designed to release webbing in a controlled manner . This feature is designed to hel[...]

3. Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the Automatic Locking Mode. How to Disengage The Automatic Locking Mode Disconnect the combination lap/shoulder belt from the buckle and allow it to r etract completely to disengage the Automatic Locking Mode and activate the[...]

BeltAlert 威 will be reactivated if the driver’s seat belt is unbuckled for more than 10 seconds and the vehicle speed is greater than 5 mph (8 km/h). BeltAlert 威 can be enabled or disabled by your authorized dealer or by following these steps: NOTE: The following steps must occur within the first 60 seconds of the ignition switch being turned[...]

Seat Belts and Pregnant Women W e recommend that pregnant women use the seat belts throughout their pregnancy . Keeping the mother safe is the best way to keep the baby safe. Pregnant women should wear the lap part of the belt across the thighs and as snug across the hips as possible. Keep the belt low so that it does not come across the abdomen. T[...]

Supplemental Restraint Systems (SRS) — Airbags This vehicle has airbags for both the driver and front passenger as a supplement to the seat belt restraint systems. The driver’s front airbag is mounted in the center of the steering wheel. The passenger’s front airbag is mounted in the instrument panel, above the glove compartment. The words SR[...]

The Advanced Front Airbags have a multistage inflator design. This allows the airbag to have differ ent rates of inflation based on the severity and type of collision. This vehicle may also be equipped with Supplemental Side Airbag Inflatable Curtains (SABIC) to protect the driver , front, and rear passengers sitting next to a win- dow . If the veh[...]

Advanced Front Airbag Features The Advanced Fr ont Airbag system has multistage driver and fr ont passenger airbags. This system provides output appropriate to the severity and type of collision as determined by the Occupant Restraint Controller (ORC), which may receive information from the impact sensors at the front of the car . The first stage i[...]

Supplemental Side Airbag Inflatable Curtain (SABIC) — If Equipped SABIC airbags offer side-impact and vehicle rollover protection to front and rear seat outboard occupants in addition to that provided by the body structure. Each airbag features inflated chambers placed adjacent to the head of each outboard occupant that reduce the potential for s[...]

The system includes sensors adjacent to both front and rear seat occupants that are calibrated to deploy the SABIC airbags during impacts that require airbag occu- pant protection. W ARNING! • If your vehicle is equipped with left and right Side Airbag Inflatable Curtain (SABIC), do not stack luggage or other cargo up high enough to block the loc[...]

W ARNING! Infants in rear-facing child restraints should NEVER ride in the front seat of a vehicle with a passenger front airbag. An airbag deployment can cause severe injury or death to infants in that position. Children that are not big enough to wear the vehicle seat belt properly (see Section on Child Restraints) should be secured in the rear s[...]

W ARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly . In some collisions, the airbags won’t deploy at all. Always wear your seat belts even though you have airbags. • Being too close to the steering wheel or instrument panel during front airb[...]

The Advanced Fr ont Airbags will not deploy in all frontal collisions, including some that may produce substantial vehicle damage — for example, some pole collisions, truck underrides, and angle of fset collisions. On the other hand, depending on the type and location of impact, Advanced Front Airbags may deploy in crashes with little vehicle fro[...]

It also includes diagnostics that will illuminate the instru- ment cluster Airbag W arning Light if a malfunction is noted. The diagnostics also recor d the nature of the malfunction. W ARNING! Ignoring the Airbag W arning Light in your instru- ment panel could mean you won’t have the airbags to protect you in a collision. If the light does not c[...]

deploy the SABIC airbags, depending on severity and type of collision. In these events, the ORC will deploy the SABIC only on the impact side of the vehicle. A quantity of non-toxic gas is generated to inflate the side curtain airbag. The inflating side curtain airbag pushes the outside edge of the headliner out of the way and covers the window . T[...]

• T urn on the interior lights, which remain on as long as the battery has power or until the ignition key is removed. • Unlock the doors automatically . If a Deployment Occurs The front airbags are designed to deflate immediately after deployment. NOTE: Front and/or side airbags will not deploy in all collisions. This does not mean something i[...]

W ARNING! Deployed airbags and seat belt pretensioners cannot protect you in another collision. Have the airbags, seat belt pretensioners, and the front passenger seat belt retractor assembly replaced by an authorized dealer as soon as possible. Also, have the Occupant Restraint Controller (ORC) system serviced as well. Maintaining Y our Airbag Sys[...]

W ARNING! (Continued) • Do not attempt to modify any part of your ad- vanced airbag system. The airbag may inflate accidentally or may not function properly if modi- fications are made. T ake your vehicle to an autho- rized dealer for any advanced airbag system ser- vice. If your seat, including your trim cover and cushion, needs to be serviced i[...]

located on the inside of the fuse block cover for the proper airbag fuses. See your authorized dealer if the fuse is good. Event Data Recorder (EDR) In the event of an accident, your vehicle is designed to recor d up to five seconds of specific vehicle data param- eters (see list below) in an event data recor der prior to the moment of airbag deplo[...]

accessing the electronic data stored, unless order ed to download data by a court with legal jurisdiction (i.e., pursuant to a warrant). A copy of the data will be provided to the custodial entity upon request. General data that does not identify particular vehicles or crashes may be released for incorporation in aggregate crash databases, such as [...]

Child Restraints Everyone in your vehicle needs to be buckled up all the time, including babies and children. Every state in the United States, and all Canadian provinces, requir e that small childr en ride in pr oper r estraint systems. This is the law , and you can be prosecuted for ignoring it. Children 12 years and under should ride properly bu[...]

• The infant carrier is only used rearwar d-facing in the vehicle. It is recommended for children who weigh up to about 20 lbs (9 kg). Convertible child seats often have a higher weight limit in the rearward-facing direction than infant carriers do, so they can be used rearwar d-facing by children who weigh more than 20 lbs (9 kg) but are less th[...]

Standards. Chrysler Gr oup LLC also recommends that you try a child restraint in the vehicle seats where you will use it before you buy it. • The restraint must be appropriate for your child’s weight and height. Check the label on the restraint for weight and height limits. • Carefully follow the instructions that come with the restraint. If [...]

• If the belt still cannot be tightened, or if pulling and pushing on the restraint loosens the belt, disconnect the latch plate from the buckle, turn the buckle around, and insert the latch plate into the buckle again. If you still cannot make the child restraint secure, try a different seating position. • Buckle the child into the restraint e[...]

Children T oo Large for Booster Seats Children who are large enough to wear the shoulder belt comfortably , and whose legs are long enough to bend over the front of the seat when their back is against the seatback, should use the lap/shoulder belt in a rear seat. • Make sure that the child is upright in the seat. • The lap portion should be low[...]

strap kits or retr o-fit kits. Y ou ar e ur ged to take advantage of all the available attachments provided with your child restraint in any vehicle. NOTE: When using the LA TCH attaching system to install a child restraint, please ensure that all seat belts not being used for occupant r estraints ar e stowed and out of reach of children. Remind al[...]

The rear seat lower anchorages are round bars, located at the rear of the seat cushion where it meets the seatback, and are just visible when you lean into the rear seat to install the child restraint. Y ou will easily feel them if you run your finger along the intersection of the seatback and seat cushion surfaces. In addition, there are tether st[...]

means of adjusting the tension in the strap. Forward- facing toddler restraints and some rear -facing infant restraints will also be equipped with a tether strap, a hook for attachment to the tether strap anchorage and a means of adjusting the tension of the strap. First, loosen the adjusters on the lower straps and on the tether strap so that you [...]

For seat belts having an Automatic Locking Retractor (ALR), pull the belt from the retractor until there is enough allowance to pass it through the child restraint and slide the latch plate into the buckle. Then, pull the belt until it is fully extended fr om the r etractor . Allow the belt to return into the retractor , pulling on the excess webbi[...]

W ARNING! Always remove the subwoofer from the vehicle whenever the tether anchors behind the subwoofer are required for proper installation of a child re- straining device. In the event of an accident, or under severe vehicle maneuvers, leaving the subwoofer unsecured in the vehicle could result in serious or fatal injury to anyone in the vehicle.[...]

W ARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap. T ransporting Pets Airbags deploying in the front seat could harm your pet. An unrestrained pet will be thrown about and possi[...]

A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered a normal part of the break-in and not inter- preted as an indication of difficulty . SAFETY TIPS T ransporting Passengers NEVER TRANSPORT P ASSENGERS IN THE CARGO AREA. W ARNING! • It is extremely dangerous to ride in a cargo[...]

Do not run the engine in a closed garage or in confined areas any longer than needed to move your vehicle in or out of the area. If it is necessary to sit in a parked vehicle with the engine running, adjust your heating or cooling controls to force outside air into the vehicle. Set the blower at high speed. If you are requir ed to drive with the tr[...]

Airbag W arning Light The light should come on and remain on for six to eight seconds as a bulb check when the ignition switch is first turned ON. If the light is not lit during starting, see your authorized dealer . If the light stays on, flickers, or comes on while driving, have the system checked by an autho- rized dealer . Defroster Check opera[...]

UNDERST ANDING THE FEA TURES OF YOUR VEHICLE CONTENTS 䡵 Mirrors .............................. 8 0 ▫ Inside Day/Night Mirror ................ 8 0 ▫ Automatic Dimming Mirror — If Equipped . . . 81 ▫ Outside Mirrors ...................... 8 1 ▫ Outside Mirrors Folding Feature .......... 8 2 ▫ Driver’s Automatic Dimming Mirrors — If [...]

▫ Four-W ay Passenger’s Power Seat — If Equipped ......................... 8 8 ▫ Head Restraints ...................... 8 8 ▫ Front Heated Seats — If Equipped ......... 8 9 ▫ Rear Heated Seats — If Equipped .......... 9 1 ▫ 60/40 Split Rear Seat ................... 9 3 䡵 Driver Memory Seat — If Equipped ......... 9 5 ▫ Setti[...]

▫ Fog Lights — If Equipped .............. 1 0 6 ▫ T urn Signals ........................ 1 0 7 ▫ Lane Change Assist ................... 1 0 8 ▫ High/Low Beam Switch ............... 1 0 8 ▫ Flash-T o-Pass ....................... 1 0 8 ▫ Headlight T ime Delay ................. 1 0 8 ▫ Interior Lights ...................... 1 0 8 ▫ F[...]

▫ Enable/Disable Parksense 威 ............. 1 2 2 ▫ Service Parksense 威 ................... 1 2 2 ▫ Cleaning Parksense 威 .................. 1 2 2 ▫ System Usage Precautions .............. 1 2 3 䡵 Parkview 威 Rear Back Up Camera — If Equipped .......................... 1 2 5 ▫ T urning Parkview 威 On Or Off — W ith Navigation/[...]

▫ Sunshade Operation .................. 1 3 6 ▫ W ind Buffeting ...................... 1 3 7 ▫ Sunroof Maintenance ................. 1 3 7 ▫ Ignition Off Operation ................. 1 3 7 ▫ Sunroof Fully Closed .................. 1 3 7 䡵 Electrical Power Outlets ................. 1 3 7 䡵 Power Inverter — If Equipped ............ 1 4[...]

MIRRORS Inside Day/Night Mirror A two-point pivot system allows for horizontal and vertical adjustment of the mirror . The mirror should be adjusted to center on the view through the rear window . Headlight glar e from vehicles behind you can be reduced by moving the small contr ol under the mirror to the night position (toward the rear of the vehi[...]

Automatic Dimming Mirror — If Equipped This mirror automatically adjusts for headlight glare from vehicles behind you. Y ou can turn the feature on or off by pr essing the button at the base of the mirr or . A light next to the button will illuminate to indicate when the dimming feature is activated. CAUTION! T o avoid damage to the mirror during[...]

W ARNING! V ehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger side convex mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in the passenger sid[...]

After selecting a mirror , move the knob in the same direction you want the mirror to move. Use the off (center) position to guard against accidentally moving a mirror position. Power mirror preselected positions can be controlled by the optional Memory Seat Feature. Refer to “Driver Memory Seat” in “Understanding the Features of Y our V ehic[...]

Illuminated V anity Mirrors — If Equipped T o access an illuminated vanity mirror , flip down one of the visors. Lift the cover to reveal the mirror . The light will turn on automatically . Sun Visor Extension — If Equipped This feature has a pull out extension on the sun visor for increased coverage. Uconnect™ Phone — IF EQUIPPED Refer to [...]

W ARNING! • DO NOT allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Be sure everyone in your vehicle is in a seat and using a seat belt properly . Front Manual Seat Adjustment Move the seat forward or[...]

W ARNING! Do not ride with the seatback reclined so that the seat belt is no longer resting against your chest. In a collision, you could slide under the seat belt and be seriously or even fatally injured. Use the recliner only when the vehicle is parked. Manual Lumbar Support Adjustment The manual lumbar support adjustment lever is located on the [...]

Eight-W ay Driver’s Power Seat The driver’s power seat switches are located on the out- board side of the driver’s seat. The bottom switch controls up/down, forward/rearwar d and tilt adjustment. The top switch controls the seatback recline adjustment. W ARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of[...]

Four-W ay Passenger’s Power Seat — If Equipped The front passenger’s power seat switches are located on the outboard side of the passenger’s seat. The bottom switch controls forward/rearwar d adjustment. The top switch controls the seatback recline adjustment. NOTE: The four-way seat does not have an up/down adjustment. W ARNING! Adjusting [...]

W ARNING! Driving a vehicle with the head restraints removed or improperly adjusted could cause serious injury or death in the event of a collision. The head restraints should always be checked prior to operating the vehicle and never adjusted while the vehicle is in motion. Always adjust the head restraints when the vehicle is in P ARK. Front Heat[...]

switch indicate the level of heat in use. T wo indicator lights will illuminate for High, one for Low and none for Off. Press the switch once to select High-level heat- ing. Press the switch a second time to select Low-level heating. Press the switch a thir d time to shut the heating elements Off. When the High-level setting is selected, the heater[...]

CAUTION! Repeated overheating of the seat could damage the heating element and/or degrade the material of the seat. Rear Heated Seats — If Equipped On vehicles equipped with rear heated seats, the seats closest to the doors are heated. The controls for these seats are located on the rear of the center console. After turning the ignition ON, you c[...]

Press the switch once to select High-level heat- ing. Press the switch a second time to select Low-level heating. Press the switch a thir d time to shut the heating elements Off. When the High-level setting is selected, the heater will provide a boosted heat level during the first four minutes of operation. Then, the heat output will drop to the no[...]

CAUTION! Repeated overheating of the seat could damage the heating element and/or degrade the material of the seat. 60/40 Split Rear Seat T o Lower Rear Seat Either side of the r ear seat can be lowered to allow for extended car go space and still maintain some rear seating room. NOTE: Be sure that the front seats are fully upright and positioned f[...]

2. Fold the rear seat completely forward. T o Raise Rear Seat Raise the rear seatback and lock it into place. If interfer- ence from the car go area pr events the seatback from fully locking, you will have difficulty returning the seat to its proper position. W ARNING! • Be certain that the seatback is securely locked into position. If the seatba[...]

Storage (Rear Seat Armrest) — If Equipped The rear seat may be equipped with a center storage armrest. Press the latch and lift the top of the armr est to access the storage bin. DRIVER MEMOR Y SEA T — IF EQUIPPED Once programmed, the memory buttons 1 and 2 on the driver’s door panel can be used to recall the driver’s seat, driver’s outsi[...]

Keyless Entry (RKE) transmitters can also be pr o- grammed to recall the same positions when the UN- LOCK button is pressed. Y our vehicle is equipped with two RKE transmitters. One or both RKE transmitters can be linked to either memory position. The memory system can accommodate up to four RKE transmitters, each one linked to either of the two me[...]

3. Adjust the driver’s seat, r ecliner , and driver’s sideview mirror to the desired positions. 4. Adjust the brake and accelerator pedals to the desired positions. 5. T urn on the radio and set the radio station presets (up to 12 AM and 12 FM stations can be set). 6. T urn the ignition switch to the LOCK position and remove the key . 7. Press [...]

T o recall the memory settings for driver one, press MEMOR Y button number 1 on the driver’s door , or the UNLOCK button on the RKE transmitter linked to memory position 1. T o recall the memory setting for driver two, pr ess MEMOR Y button number 2 on the driver’s door , or the UNLOCK button on the RKE transmitter linked to memory position 2. [...]

Easy Entry/Exit Seat This feature provides automatic driver’s seat positioning which will enhance driver mobility out of and into the vehicle. There are two possible Easy Entry/Exit adjustments available: • The seat cushion will move rearwar d approximately 2.5 in (60 mm), if the starting position of the seat is greater than or equal to 2.67 in[...]

TO OPEN AND CLOSE THE HOOD T o open the hood, two latches must be released. 1. Pull the release lever located below the instrument panel and in front of the driver’s door . 2. Reach under the hood, move safety latch to the left and lift the hood. CAUTION! T o prevent possible damage, do not slam the hood to close it. Use a firm downward push at t[...]

W ARNING! Be sure the hood is fully latched before driving your vehicle. If the hood is not fully latched, it could open when the vehicle is in motion and block your vision. Failure to follow this warning could result in serious injury or death. LIGHTS Multifunction Lever The multifunction lever controls the operation of the headlights, turn signal[...]

Headlights and Parking Lights T urn the end of the multifunction lever to the first detent for parking light operation. T urn to the second detent for headlight operation. T urn to the third detent for Auto- matic Headlight operation (if equipped). Automatic Headlights — If Equipped T urn the end of the multifunction lever to the third detent (AU[...]

This system performs two functions. W ith the engine running and the multifunction lever in the AUTO posi- tion, the headlights will turn on and off based on the surrounding light levels. Headlights On Automatically With Wipers If your vehicle is equipped with Automatic Headlights, it also has this customer-programmable feature. When your headlight[...]

T o Activate 1. Select “Auto High Beams.” Refer to “Electronic V e- hicle Information Center (EVIC)/Customer- Programmable Featur es” in “Understanding Y our Instru- ment Panel” for further information. 2. T urn the end of the multifunction lever to the AUTO headlight position. 3. Push the multifunction lever away from you (toward front[...]

Automatic Headlight Leveling — HID Headlights Only This feature prevents the headlights from interfering with the vision of oncoming drivers. Headlight leveling automatically adjusts the height of the headlight beam in reaction to changes in vehicle pitch. Instrument Panel Dimmer Rotate the center potion of the lever to the extreme bottom positio[...]

Battery Saver Feature If the multifunction lever is left in the interior light position, parking light position, or the headlight position when the ignition switch is moved to the LOCK position, the battery saver feature will automatically turn off the exterior and interior lights after eight minutes. Normal operation will resume when the ignition [...]

NOTE: • T urning on the high beam headlights turns off the fog lights. • A front fog light is a lighting device that provides illumination in front of the vehicle under conditions of fog, rain, snow , or dust. The front fog lights supple- ment the low beams of a standard headlight system. • Proper aim and adjustment of the front fog lights sh[...]

Lane Change Assist T ap the lever up or down once, without moving beyond the detent, and the turn signal (right or left) will flash three times then automatically turn off. High/Low Beam Switch Push the multifunction lever away from you to switch the headlights to high beam. Pull the multifunction lever toward you to switch the headlights back to l[...]

lens a second time. There are also reading lights located above the rear doors. Each light can be turned on by pressing the front recessed area of the lens. T o turn these lights off, press the recessed area of the lens a second time. WINDSHIELD WIPERS AND W ASHERS The windshield wiper/washer control lever is located on the right side of the steeri[...]

Windshield Wiper Operation Rotate the end of the lever upward to the LO position for low-speed wiper operation. Rotate the end of the lever upward to the HI position for high-speed wiper operation. CAUTION! Always remove any buildup of snow that prevents the windshield wiper blades from returning to the “park” position. If the windshield wiper [...]

NOTE: The wiper delay times depend on vehicle speed. If the vehicle is moving less than 10 mph (16 km/h), delay times will be doubled. Windshield Washer Operation T o use the washer , pull the lever toward you and hold while spray is desired. If the lever is pulled while in the delay range, the wiper will operate for several wipe cycles after the l[...]

Mist Use the Mist feature when weather conditions make occasional usage of the wipers necessary . Pull down and release the control lever for a single wiping cycle. Rain Sensing Wipers — If Equipped This feature senses moisture on the windshield and automatically activates the wipers for the driver . The feature is especially useful for road spla[...]

NOTE: • The Rain Sensing feature will not operate when the wiper switch is in the low or high-speed position. • The Rain Sensing feature may not function properly when ice, or dried salt water is present on the wind- shield. • Use of Rain-X 威 or products containing wax or silicone may reduce Rain Sensing performance. • A customer programm[...]

TIL T/TELESCOPING STEERING COLUMN This feature allows you to tilt the steering column upward or downward. It also allows you to lengthen or shorten the steering column. The tilt/telescoping control handle is located below the steering wheel at the end of the steering column. T o unlock the steering column, push the control handle downward (towar d [...]

ADJUST ABLE PEDALS — IF EQUIPPED This feature allows both the brake and accelerator pedals to move toward or away from the driver to provide improved position with the steering wheel. The adjust- able pedal system is designed to allow a greater range of driver comfort for steering wheel tilt and seat position. The position of the brake and accele[...]

Press the top of the switch to move the pedals rearward (toward the driver). • The pedals can be adjusted with the ignition OFF . • The pedals can be adjusted while driving. • The pedals cannot be adjusted when the vehicle is in REVERSE (R) or when the Electronic Speed Control is on. A message will be displayed in the Electronic V ehicle Info[...]

The Electronic Speed Control lever is located on the right side of the steering wheel. NOTE: In order to ensure proper operation, the Elec- tronic Speed Control System has been designed to shut down if multiple Speed Control functions are operated simultaneously . If this occurs, the Electronic Speed Con- trol System can be reactivated by pushing t[...]

T o Set a Desired Speed When the vehicle has reached the desired speed, press down on the lever and release. Release the accelerator and the vehicle will operate at the selected speed. NOTE: The vehicle should be traveling at a steady speed and on level ground before pressing the SET lever . T o Deactivate A soft tap on the brake pedal, pulling the[...]

T apping the SET DECEL lever once will result i na1m p h (2 km/h) speed decrease. Each time the lever is tapped, speed decreases. T o Accelerate for Passing Press the accelerator as you would normally . When the pedal is released, the vehicle will return to the set speed. Using Electronic Speed Control On Hills The transmission may downshift on hil[...]

ParkSense 威 will remember the last system state (enabled or disabled) fr om the last ignition cycle when the ignition is changed to the ON position. ParkSense 威 can be active only when the shift lever is in REVERSE. If ParkSense 威 is enabled at this shift lever position, the system will be active until the vehicle speed is increased to approx[...]

When the ignition is turned to the ON position, the warning display will turn ON all of its LEDs for about one second. Each side of the warning display has six yellow and two red LEDs. The vehicle is close to the obstacle when the red LED is ON. The system dimly illuminates the two outer most yellow LEDs when it is ON and detecting no obstacles. Th[...]

NOTE: The Rear Park Assist system will MUTE the radio, if on, when the system is sounding an audio tone. Enable/Disable ParkSense 姞 ParkSense 威 can be enabled and disabled with a switch located on the upper switch bank of the instrument panel. Press the switch once to turn ParkSense 威 on, push the switch a second time to turn Park- Sense 威 [...]

System Usage Precautions NOTE: • Ensure that the rear bumper is free of dirt and debris to keep ParkSense 威 operating properly . • Jackhammers, large trucks, and other vibrations could affect the performance of ParkSense 威 . • When you turn ParkSense 威 off, the instrument cluster will display “P ARK ASSIST DISABLED.” Further- more, [...]

• Objects must not be within 12 in (30 cm) from the rear fascia/bumper while driving the vehicle. Failure to do so can result in the system misinterpreting a close object as a sensor problem, causing the “SER VICE P ARK ASSIST SYSTEM” message to be displayed in the instrument cluster . CAUTION! • ParkSense 威 is only a parking aid and it i[...]

W ARNING! (Continued) • Before using the ParkSense 威 Rear Park Assist System, it is strongly recommended that the ball mount and hitch ball assembly is disconnected from the vehicle when the vehicle is not used for towing. Failure to do so can result in injury or damage to vehicles or obstacles because the hitch ball will be much closer to the [...]

CAUTION! • T o avoid vehicle damage, ParkV iew 威 should only be used as a parking aid. The ParkV iew 威 camera is unable to view every obstacle or object in your drive path. • T o avoid vehicle damage, the vehicle must be driven slowly when using ParkV iew 威 to be able to stop in time when an obstacle is seen. It is recom- mended that the [...]

T urning ParkView 姞 On or Off — Without Navigation/Multimedia Radio 1. Press the “menu” hard key . 2. Select “system setup” soft key . 3. Enable or disable the rear camera feature by selecting “enable rear camera in reverse” soft key . 4. When the vehicle is shifted into REVERSE, an image of the rear of the vehicle will appear with [...]

Press the lens to turn these lights on. Press a second time to turn the lights off. The lights also turn on when a front door or rear door is opened. The lights will also turn on when the UNLOCK button on the Remote Keyless Entry (RKE) transmitter is pressed. Sunglasses Storage At the rear of the console a compartment is provided for the storage of[...]

NOTE: HomeLink 威 is disabled when the V ehicle Secu- rity Alarm is active. W ARNING! • Y our motorized door or gate will open and close while you are training the Universal T ransceiver . Do not train the transceiver if people, pets or other objects are in the path of the door or gate. Only use this transceiver with a garage door opener that ha[...]

It is recommended that a new battery be placed in the hand-held transmitter of the device being copied to HomeLink 威 for more efficient training and accurate transmission of the radio-frequency signal. Y our vehicle should be parked outside of the garage while training. 1. T urn the ignition switch to the ON/RUN position. 2. Place the handheld tr[...]

NOTE: After training a HomeLink 威 channel, if the garage door does not operate with HomeLink 威 and the garage door opener was manufactured after 1995, the garage door opener may have rolling code. If so, proceed to the heading “Programming A Rolling Code System.” 5. PROGRAMMING A ROLLING CODE SYSTEM At the garage door opener motor (in the g[...]

7. Return to the vehicle and press the programmed HomeLink 威 button twice (holding the button for two seconds each time). If the device is plugged in and activates, programming is complete. If the device does not activate, press the button a third time (for two seconds) to complete the training. If you have any problems or requir e assistance, pl[...]

Then proceed with Step 4 under “Programming HomeLink 威 ” earlier in this section. Using HomeLink 姞 T o operate, press and release the programmed HomeLink 威 button. Activation will now occur for the trained device (i.e., garage door opener , gate operator , security system, entry door lock, home/office lighting, etc.,). The handheld transm[...]

• Press the LEARN button on the garage door opener to complete the training for rolling code. • Did you unplug the device for training and remember to plug it back in? If you are having any problems or requir e assistance, please call toll-free 1–800–355–3515 or , on the Internet at www .HomeLink.com for information or assistance. General[...]

POWER SUNROOF — IF EQUIPPED The power sunroof switch is located between the sun visors on the overhead console. W ARNING! • Never leave children in a vehicle with the key in the ignition switch. Occupants, particularly unat- tended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may [...]

Opening Sunroof — Express Press the switch rearwar d and r elease, and the sunroof will open automatically from any position. The sunroof will open fully , then stop automatically . This is called “Express Open”. During Express Open operation, any movement of the sunroof switch will stop the sunroof. Closing Sunroof — Express Press the swit[...]

NOTE: The sunshade cannot be closed if the sunroof is open. Wind Buffeting W ind buffeting can be described as the perception of pressur e on the ears or a helicopter-type sound in the ears. Y our vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occu[...]

NOTE: • All accessories connected to the “battery” powered outlets should be removed or turned off when the vehicle is not in use to protect the battery against discharge. • T o ensure proper operation a MOP AR 威 knob and element must be used. • Do not exceed the maximum power of 160 W atts (13 Amps) at 12 V olts. If the 160 W att (13 A[...]

The rear power outlet (if equipped) is located in the left rear cargo area. W ARNING! T o avoid serious injury or death: • Only devices designed for use in this type of outlet should be inserted into any 12 V olt outlet. • Do not touch with wet hands. • Close the lid when not in use and while driving the vehicle. • If this outlet is mishand[...]

CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery , even when not in use (i.e., cellular phones, etc.). Eventually , if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting. • Accessories that draw higher power (i.e., [...]

The power inverter is designed with built-in overload protection. If the power rating of 150 W atts is exceeded, the power inverter will automatically shut down. Once the electrical device has been r emoved fr om the outlet the inverter should automatically reset. If the power rating exceeds approximately 170 W atts, the power inverter may have to [...]

W ARNING! T o avoid serious injury or death: • Do not use a three-prong adaptor . • Do not insert any objects into the receptacles. • Do not touch with wet hands. • Close the lid when not in use. • If this outlet is mishandled it may cause an electric shock and failure. CUPHOLDERS There are two cupholders for the front seat passengers loc[...]

CARGO AREA FEA TURES Cargo Light The cargo area light is activated by opening the liftgate, opening any door , or by rotating the dimmer control on the multifunction lever to the extreme top position. If all doors are closed and only the liftgate is open, pushing on the cargo light lens surface will turn off all interior lights. Push on the lens su[...]

Retractable Cargo Area Cover — If Equipped NOTE: The purpose of this cover is for privacy , not to secure loads. It will not prevent cargo from shifting or protect passengers from loose cargo. T o cover the cargo area: 1. Grasp the cover at the center handle. Pull it over the cargo area. 2. Insert the pins on the ends of the cover into the slots [...]

W ARNING! In an accident, a loose cargo cover in the vehicle could cause injury . It could fly around in a sudden stop and strike someone in the vehicle. Do not store the cargo cover on the cargo floor or in the passenger compartment. Remove the cover from the vehicle when taken from its mounting. Do not store it in the vehicle. Cargo Tie-Down Hook[...]

W ARNING! • T o help protect against personal injury , passengers should not be seated in the rear cargo area. The rear cargo space is intended for load carrying purposes only , not for passengers, who should sit in seats and use seat belts. • Cargo tie-down hooks are not safe anchors for a child seat tether strap. In a sudden stop or colli- si[...]

Cargo Load Floor The panel in the load floor is reversible for added utility . One side is carpeted and the other side features a plastic lined tray which holds a variety of items. The cargo load floor is held by spring loaded latches. In order to use the cargo load floor , use the following procedur e: NOTE: The cargo load floor latches should not[...]

REAR WINDOW FEA TURES Rear Window Wiper/Washer The rear wiper/washer is controlled by a rotary switch located on the control lever . The control lever is located on the right side of the steering column. Rotate the switch upward to the “On” position to activate the rear wiper . NOTE: The rear wiper operates in an intermittent mode only . Rotate[...]

If the liftgate flipper glass is open, connection to the rear window wiper is interr upted preventing activation of the rear wiper blade. When the liftgate flipper glass is closed, the rear wiper switch, or the ignition switch, needs to be turned OFF and ON to restart the rear wiper . Rear Window Defroster The r ear window defroster button is locat[...]

ROOF LUGGAGE RACK — IF EQUIPPED The crossbars and siderails are designed to carry the weight on vehicles equipped with a luggage rack. The load must not exceed 150 lbs (68 kg), and should be uniformly distributed over the luggage rack crossbars. NOTE: If not equipped with crossbars, your authorized dealer can order and install MOP AR 威 crossbar[...]

• The grab handles on the back of the vehicle (if equipped) are not to be used as a towing feature. CAUTION! • T o prevent damage to the roof of your vehicle, DO NOT carry any loads on the roof rack without the crossbars installed. The load should be secured and placed on top of the crossbars, not directly on the roof. If it is necessary to pla[...]

W ARNING! Cargo must be securely tied before driving your vehicle. Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in per- sonal injury or property damage. Follow the roof rack cautions when carrying cargo on your roof rack. 152 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE I n f o r m a t i o n P r o v i d e[...]

UNDERST ANDING YOUR INSTRUMENT P ANEL CONTENTS 䡵 Instrument Panel Features ............... 1 5 6 䡵 Instrument Cluster .................... 1 5 7 䡵 Instrument Cluster Descriptions ........... 1 5 8 䡵 Electronic V ehicle Information Center (EVIC) . . 168 ▫ Electronic V ehicle Information Center (EVIC) Displays ........................... 1 [...]

▫ Clock Setting Procedur e — RER/REN Radio ............................. 1 8 5 䡵 Media Center 130 (RES) — AM/FM Stereo Radio W ith CD Player (MP3 AUX Jack) ....... 1 8 8 ▫ Operating Instructions — Radio Mode ..... 1 8 8 ▫ Operation Instructions — CD Mode For CD And MP3 Audio Play ................. 1 9 1 ▫ Notes On Playing MP3 File[...]

▫ Electronic Serial Number/Sirius Identification Number (ESN/SID) ......... 2 1 5 ▫ Selecting Uconnect™ Multimedia (Satellite) Mode ............................. 2 1 5 ▫ Satellite Antenna ..................... 2 1 5 ▫ Reception Quality .................... 2 1 6 ▫ Operating Instructions - Uconnect™ Multimedia (Satellite) Mode ........[...]

INSTRUMENT P ANEL FEA TURES 1 — Air Outlet 5 — Upper Switch Bank 9 — Lower Switch Bank 2 — Instrument Cluster 6 — Power Outlet/Cigar Lighter 10 — Climate Controls 3 — Radio 7 — Storage Bin 1 1 — Ignition Switch 4 — Glove Compartment 8 — Power Outlet 12 — Storage Bin 156 UNDERST ANDING YOUR INSTRUMENT P ANEL I n f o r m a t i[...]

INSTRUMENT CLUSTER 4 UNDERST ANDING YOUR INSTRUMENT P ANEL 157 I n f o r m a t i o n P r o v i d e d b y :[...]

INSTRUMENT CLUSTER DESCRIPTIONS 1. Speedometer Indicates vehicle speed. 2. Brake W arning Light This light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on, it may indicate that the parking brake is applied, that the brake fluid level is low , or that there is a problem with th[...]

W ARNING! Driving a vehicle with the red brake light on is dangerous. Part of the brake system may have failed. It will take longer to stop the vehicle. Y ou could have an accident. Have the vehicle checked immediately . V ehicles equipped with the Anti-Lock Brake System (ABS), are also equipped with Electronic Brake Force Distribution (EBD). In th[...]

the ON position before engine start. If the bulb does not come on when turning the key fr om OFF to ON, have the condition checked promptly . Certain conditions such as a loose or missing gas cap, poor fuel quality , etc., may illuminate the light after engine start. The vehicle should be serviced if the light stays on through several of your typic[...]

7. Anti-Lock Brake (ABS) Light This light monitors the Anti-Lock Brake System (ABS). The light will turn on when the ignition switch is turned to the ON position and may stay on for as long as four seconds. If the ABS light remains on or turns on while driving, it indicates that the Anti-Lock portion of the brake system is not functioning and that [...]

1 1. Electronic Stability Program (ESP) Indicator Light / T raction Control System (TCS) Indicator Light If this indicator light flashes during accelera- tion, apply as little throttle as possible. While driving, ease up on the accelerator . Adapt your speed and driving to the prevailing road con- ditions, and do not switch off the Electronic Stabi[...]

Y our vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly . The TPMS malfunction indicator is combined with the low tire pressur e telltale. When the system detects a malfunction, the telltale will flash for approximately one minute and then r emain continuously illuminated. This se[...]

The gauge pointer will likely indicate a higher tempera- ture when driving in hot weather , up mountain grades, or when towing a trailer . It should not be allowed to exceed the upper limits of the normal operating range. CAUTION! Driving with a hot engine cooling system could damage your vehicle. If the temperature gauge reads “H” pull over an[...]

15. TOW/HAUL Indicator Light — If Equipped This light will illuminate when the TOW/ HAUL button has been selected. The TOW/ HAUL button is located in the center of the instrument panel (below the climate controls). 16. Electronic Stability Program (ESP) Indicator Light / Brake Assist System (BAS) W arning Light The malfunction light for the Elect[...]

18. Seat Belt Reminder Light When the ignition switch is first turned ON, this light will turn on for five to eight seconds as a bulb check. During the bulb check, if the driver’s seat belt is unbuckled, a chime will sound. After the bulb check or when driving, if the driver or front passenger seat belt remains unbuckled, the Seat Belt Indicator [...]

22. Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON position. 23. Electronic Throttle Control (ETC) W arning Light This light informs you of a problem with the Electronic Throttle Control (ETC) system. If a problem is detected the light will come on while the engine is running. Cycle the ignitio[...]

If jump starting is required, refer to “Jump Starting Procedur es” in “What T o Do In Emergencies”. 26. Low Fuel Light This light will turn on, and a single chime will sound, when the fuel level drops to 1/8 tank. The Low Fuel W arning Light may turn on and of f again, especially during and after hard braking, accelerations, or turns. This [...]

• Compass Display • Outside T emperatur e Display • T rip Computer Functions The system allows the driver to select information by pressing the following buttons mounted on the steering wheel: MENU Button Press and release the MENU button and the mode displayed will change between T rip Functions, Personal Settings, and System Sta- tus. FUNCT[...]

• KEY NOT PROGRAMMED — KEY NOT PRO- GRAMMED • WRONG KEY — KEY DOES NOT BELONG TO VEHICLE • KEY NOT PROGRAMMED — EXCEEDED KEY PRO- GRAM LIMIT • PROGRAMMING ACTIVE — NEW KEY PRO- GRAMMED • SER VICE SECURITY KEY • DRIVER/P ASSENGER DOOR OPEN (with graphic) • LEFT/RIGHT REAR DOOR OPEN (with graphic) • X DOORS OPEN (with graphic)[...]

• W ASHER FLUID LOW (with graphic) • COOLANT LOW (with graphic) • OIL CHANGE REQUIRED • OIL CHANGE RESET • CHECK GAUGES • AUTO HIGH BEAMS ON • AUTO HIGH BEAMS OFF • P ARK ASSIST DISABLED • SER VICE SUSPENSION • SER VICE P ARK ASSIST SYSTEM • TRANSMISSION OVER TEMP • CHECK SHIFT PROCEDURE • SER VICE 4WD SYSTEM • 4WD SYSTE[...]

• DRIVER 2 MEMOR Y • ADJ. PEDALS DISABLED — CRUISE CONTROL SET • ADJ. PEDALS DISABLED — SHIFTER IN REVERSE • LOW TIRE PRESSURE • CHECK TPM SYSTEM • LEFT FRONT LOW PRESSURE (Premium TPM Sys- tem Only) • RIGHT FRONT LOW PRESSURE (Premium TPM Sys- tem Only) • LEFT REAR LOW PRESSURE (Premium TPM System Only) • RIGHT REAR LOW PRESS[...]

will flash in the EVIC display for approximately 10 sec- onds after a single chime has sounded, to indicate the next scheduled oil change interval. The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate, dependent upon your personal driving style. Unless reset, this message will continue[...]

The T rip Functions mode displays the following informa- tion: A verage Fuel Economy / Fuel Saver Mode Shows the average fuel economy since the last reset. When the fuel economy is reset, the display will read “RESET” or show dashes for two seconds. Then, the history information will be erased, and the averaging will continue from the last fuel[...]

Distance T o Empty (DTE) Shows the estimated distance that can be traveled with the fuel remaining in the tank. This estimated distance is determined by a weighted average of the instantaneous and average fuel economy , according to the current fuel tank level. DTE cannot be reset through the FUNCTION SELECT button. NOTE: Significant changes in dri[...]

T rip B Shows the total distance traveled for T rip B since the last reset. Elapsed T ime Shows the total elapsed time of travel since the last reset when the ignition switch is in the ACC position. Elapsed time will increment when the ignition switch is in the ON or ST AR T position. Display Units of Measure In T o make your selection, press and r[...]

Manual Compass Calibration If the compass appears erratic and the “CAL” indicator does not appear in the EVIC display , you must put the compass into the Calibration Mode manually , as follows: 1. T urn on the ignition switch. 2. Press the MENU button until Personal Settings (Customer-Pr ogrammable Features) menu is reached. 3. Press the SCROLL[...]

1. T urn the ignition switch ON. 2. Press the MENU button until Personal Settings (Customer-Pr ogrammable Features) menu is reached. 3. Press the SCROLL button until “Compass V ariance” is displayed in the EVIC. 4. Press and release the FUNCTION SELECT button to change the variance number . Continue until desired number is reached. 5. Press eit[...]

FUNCTION SELECT button while in this display to select English, Espanol, or Francais. Then, as you con- tinue, the information will display in the selected lan- guage. NOTE: The EVIC will not change the Uconnect™ lan- guage selection. Auto Door Locks When YES (Y) is selected, all of the doors will lock automatically when the vehicle reaches a spe[...]

feature may be selected with or without the “Flash Lamps with Lock” feature. T o make your selection, press and r elease the FUNCTION SELECT button until YES (Y) or NO (N) appears. Flash Lamps with Lock When YES (Y) is selected, the front and rear turn signals will flash when the doors are locked or unlocked with the RKE transmitter . This feat[...]

NOTE: T urning the headlights on during the daytime causes the instrument panel lights to dim. T o incr ease the brightness, refer to “Lights” in “Understanding The Features Of Y our V ehicle”. Rain Sensing W ipers — If Equipped When YES (Y) is selected, the system will automatically activate the windshield wipers if it senses moisture on[...]

unlocked with the RKE transmitter . T o make your selec- tion, press and release the FUNCTION SELECT button until “OFF ,” “30 sec.,” “60 sec.,” or “90 sec.” appears. Hill Start Assist T o make your selection, press and release the FUNC- TION SELECT button until YES (Y) or NO (N) appears. Display Units of Measure In: The EVIC, odomet[...]

NOTE: • T ires heat up during normal driving conditions. Heat will cause the tire pressure to increase from 2 to 6 psi (14 to 41 kPa) during normal driving conditions. Refer to “T ires-General Information/T ir e Inflation Pres- sures” in “Starting And Operating” for additional information. • Y our system can be set to display pr essure [...]

Refer to your Uconnect™ Multimedia REN, RER or RBZ user’s manual for detailed operating instructions. Operating Instructions — V oice Command System — If Equipped Refer to “V oice Command” in the Uconnect™ User Manual located on the DVD for further details. Operating Instructions — Uconnect™ Phone — If Equipped Refer to “Uconn[...]

2. T ouch the screen where the time is displayed. The clock setting menu will appear on the screen. 3. When this feature is on, a check mark will appear in the box next to the words “Daylight Savings.” T ouch the screen where the words “Daylight Savings” are dis- played to change the current setting. Show T ime if Radio is Off When selected[...]

satellite clock is Greenwich Mean T ime (GMT). This is the worldwide standard for time. This makes the system’s clock very accurate once the appropriate time zone and daylight savings information is set. T o Manually Set the Clock — RER/REN 1. T urn on the radio. 2. T ouch the screen where the time is displayed. 3. T ouch the screen where “Us[...]

Show T ime if Radio is Off When selected, this feature will display the time of day on the touch screen when the radio is turned off. Proceed as follows to change the current setting: 1. T urn on the radio. 2. T ouch the screen where the time is displayed. 3. T ouch the screen where “User Clock” is displayed, the clock setting menu will appear [...]

MEDIA CENTER 130 (RES) — AM/FM STEREO RADIO WITH CD PLA YER (MP3 AUX JACK) NOTE: The radio sales code is located on the lower right side of the radio faceplate. Operating Instructions — Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/V olume Control (Rotary) Push the ON/VOLUME control kn[...]

SEEK Buttons Press and release the SEEK buttons to search for the next listenable station in AM/FM mode. Pr ess the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping, until you release it. TIME Button [...]

Push the rotary TUNE/SCROLL control knob a second time and MID will display . T urn the TUNE/SCROLL control knob to the right or left to incr ease or decrease the mid-range tones. Push the rotary TUNE/SCROLL control knob a third time and TREBLE will display . T urn the TUNE/SCROLL control knob to the right or left to incr ease or decrease the trebl[...]

Y ou may add a second station to each pushbutton by repeating the above procedur e with this exception: Press the SET/RND button twice and SET 2 will show in the display window . Each button can be set for SET 1 and SET 2 in both AM and FM. This allows a total of 12 AM and 12 FM stations to be stor ed into pushbutton memory . The stations stored in[...]

If you insert a disc with the ignition ON and the radio ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will show the track number , and index time in minutes and seconds. Play will begin at the start of track 1. CAUTION! • This CD player will accept 4-3/4 in (12 cm) discs only . The use of o[...]

the current selection. Pressing and holding the SEEK button will allow faster scrolling through the tracks in CD and MP3 modes. TIME Button Press this button to change the display from a large CD playing time display to a small CD playing time display . R W/FF Press and hold the FF (Fast Forward) button and the CD player will begin to fast forward [...]

Supported Medium Formats (File Systems) The medium formats supported by the radio are ISO 9660 Level 1 and Level 2 and includes the Joliet extension. When reading discs recorded using formats other than ISO 9660 Level 1 and Level 2, the radio may fail to read files properly and may be unable to play the file nor- mally . UDF and Apple HFS formats a[...]

Supported MP3 File Formats The radio will recognize only files with the *.MP3 exten- sion as MP3 files. Non-MP3 files named with the *.MP3 extension may cause playback problems. The radio is designed to recognize the file as an invalid MP3 and will not play the file. When using the MP3 encoder to compress audio data to an MP3 file, the bit rate and[...]

Loading times for playback of MP3 files may be affected by the following: • Media - CD-R W media may take longer to load than CD-R media • Medium formats - Multisession discs may take longer to load than non-multisession discs • Number of files and folders - Loading times will increase with more files and folders T o increase the speed of dis[...]

MEDIA CENTER 130 (RES/RSC) — AM/FM STEREO RADIO WITH CD PLA YER (MP3 AUX JACK) AND SIRIUS RADIO NOTE: The radio sales code is located on the lower right side of the radio faceplate. Operating Instructions — Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/V olume Control (Rotary) Push the[...]

to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping until you release it. V oice Command System (Radio) — If Equipped Refer to “V oice Command” in the Uconnect™ User Manual located on the DVD for further deta[...]

3. After adjusting the hours, press the right side TUNE/ SCROLL control knob to set the minutes. The minutes will begin to blink. 4. Adjust the minutes using the right side TUNE/ SCROLL control knob. Press the TUNE/SCROLL control knob to save time change. 5. T o exit, press any button/knob or wait five seconds. The clock can also be set by pressing[...]

Push the rotary TUNE/SCROLL control knob a second time and MID will display . T urn the TUNE/SCROLL control knob to the right or left to incr ease or decrease the mid-range tones. Push the rotary TUNE/SCROLL control knob a third time and TREBLE will display . T urn the TUNE/SCROLL control knob to the right or left to incr ease or decrease the trebl[...]

Program T ype 16-Digit Character Display College College Country Country Foreign Language Language Information Inform Jazz Jazz News News Nostalgia Nostalga Oldies Oldies Personality Persnlty Public Public Rhythm and Blues R & B Religious Music Rel Musc Religious T alk Rel T alk Rock Rock Soft Soft Soft Rock Soft Rck Program T ype 16-Digit Char[...]

SETUP Button Pressing the SETUP button allows you to select between the following items: • Set Clock — Pressing the SELECT button will allow you to set the clock. Adjust the hours by turning the TUNE/SCROLL control knob. After adjusting the hours, press the TUNE/SCROLL control knob to set the minutes. The minutes will begin to blink. Adjust the[...]

Button s1-6 These buttons tune the radio to the stations that you commit to pushbutton memory (12 AM and 12 FM stations). DISC/AUX Button Pressing the DISC/AUX button will allow you to switch from AM/FM modes to DISC/AUX mode. Operation Instructions — CD MODE for CD and MP3 Audio Play NOTE: • The ignition switch must be in the ON or ACC positio[...]

CAUTION! (Continued) • Do not use adhesive labels. These labels can peel away and jam the player mechanism. • RES is a single CD player . Do not attempt to insert a second CD if one is already loaded. • Dual-media disc types (one side is a DVD, the other side is a CD) should not be used, and they can cause damage to the player . EJECT Button [...]

AM/FM Button Press the button to select either AM or FM mode. SET/RND Button (Random Play Button) Press this button while the CD is playing to activate Random Play . This feature plays the selections on the compact disc in random order to provide an interesting change of pace. Press the right SEEK button to move to the next ran- domly selected trac[...]

• Maximum number of folders. (The radio display of file names and folder names is limited. For lar ge numbers of files and/or folders, the radio may be unable to display the file name and folder name and will assign a number instead. W ith a maximum number of files, exceeding 20 folders will result in this display . W ith 200 files, exceed- ing 5[...]

MPEG Specification Sampling Frequency (kHz) Bit Rate (kbps) MPEG-1 Audio Layer 3 48, 44.1, 32 320, 256, 224, 192, 160, 128, 1 12, 96, 80, 64, 56, 48, 40, 32 MPEG-2 Audio Layer 3 24, 22.05, 16 160, 128, 144, 1 12, 96, 80, 64, 56, 48, 40, 32, 24, 16, 8 ID3 T ag information for artist, song title, and album title are supported for version 1 ID3 tags. [...]

LIST Button (CD Mode for MP3 Play) Pressing the LIST button will bring up a list of all folders on the disc. Scrolling up or down the list is done by turning the TUNE/SCROLL control knob. Selecting a folder by pressing the TUNE/SCROLL control knob will begin playing the files contained in that folder (or the next folder in sequence if the selection[...]

TIME Button (Auxiliary Mode) Press this button to change the display to time of day . The time of day will display for five seconds (when the ignition is OFF). Operating Instructions - Uconnect™ Phone (If Equipped) Refer to “Uconnect™ Phone” in the Uconnect™ User Manual located on the DVD for further details. Operating Instructions - Ucon[...]

Connecting The iPod 姞 Use the pr ovided connection cable to connect an iPod 威 to the vehicle’s 16–pin connector port (which is located in the glove compartment on some vehicles). Once the iPod 威 is connected and synchronized to the vehicle’s UCI system (iPod 威 may take a few seconds to connect), the iPod 威 starts charging and is rea[...]

Play Mode When switched to UCI mode, the iPod 威 automatically starts Play mode. In Play mode, you may use the following buttons on the radio faceplate to control the iPod 威 and display data: • Use the TUNE control knob to select the next or previous track. • T urning it clockwise (forward) by one click, while playing a track, skips to the n[...]

• While a track is playing, press the INFO button to see the associated metadata (artist, track title, album, etc.) for that track. Pressing the INFO button again jumps to the next scr een of data for that track. Once you have seen all screens, the last INFO button press will take you back to the play mode screen on the radio. • Pressing the RE[...]

• During all List modes, the iPod 威 displays all lists in “wrap-around” mode. So if the track is at the bottom of the list, just turn the wheel backwards (counter-clockwise) to get to the track faster . • In List mode, the radio PRESET buttons are used as shortcuts to the following lists on the iPod 威 . • Preset 1 – Playlists • Pr[...]

CAUTION! • Leaving the iPod 威 (or any supported device) any- where in the vehicle in extreme heat or cold can alter the operation or damage the device. Follow the device manufacturer ’ s guidelines. • Placing items on the iPod 威 , or connections to the iPod 威 in the vehicle, can cause damage to the device and/or to the connectors. W ARN[...]

information, call the toll-free number 888-539-7474, or visit the Sirius web site at www .sirius.com, or at www- .siriuscanada.ca for Canadian residents. Electronic Serial Number/Sirius Identification Number (ESN/SID) Please have the following information available when calling: 1. The Electronic Serial Number/Sirius Identification Number (ESN/SID)[...]

bikes should be placed as far rearward as possible, within the loading design of the rack. Do not place items directly on or above the antenna. Reception Quality Satellite reception may be interrupted due to one of the following reasons: • The vehicle is parked in an underground parking structur e or under a physical obstacle. • Dense tree cove[...]

INFO Button Pressing the INFO button will cycle the display informa- tion between Artist, Song T itle, and Composer (if avail- able). Also, pressing and holding the INFO button for an additional three seconds will make the radio display the Song T itle all of the time (press and hold again to return to normal display). R W/FF Pressing the RW (Rewin[...]

SETUP Button Pressing the SETUP button allows you to select the following items: • Display Sirius ID number — Press the AUDIO/ SELECT button to display the Sirius ID number . This number is used to activate, deactivate, or change the Sirius subscription. SET Button – T o Set the Pushbutton Memory When you are receiving a channel that you wish[...]

REMOTE SOUND SYSTEM CONTROLS — IF EQUIPPED The remote sound system controls ar e located on the rear surface of the steering wheel. Reach behind the wheel to access the switches. The right-hand control is a rocker-type switch with a pushbutton in the center and controls the volume and mode of the sound system. Pressing the top of the rocker switc[...]

The button located in the center of the left-hand control will tune to the next preset station that you have pro- grammed in the radio preset pushbutton. CD Player Pressing the top of the switch once will go to the next track on the CD. Pressing the bottom of the switch once will go to the beginning of the current track, or to the beginning of the [...]

NOTE: If you experience difficulty in playing a particu- lar disc, it may be damaged (i.e., scratched, reflective coating removed, a hair , moisture or dew on the disc) oversized, or have protection encoding. T ry a known good disc before considering disc player service. RADIO OPERA TION AND CELLULAR PHONES Under certain conditions, the cellular ph[...]

The instrument panel features four dual-vane airflow registers. T wo registers are located on the outer ends of the instrument panel and two are located in the center of the instrument panel. These registers can be closed to partially block airflow , and they can be adjusted to direct airflow where the occupant desires. Blower Control The blower co[...]

Defrost Air is directed to the windshield through the outlets at the base of the windshield. Air is also directed to the front door windows through the side window demister grilles. Some airflow is deliver ed to the floor while in defrost so that comfort can be maintained. Defrost/Floor Air flows through the front and rear floor outlets and the out[...]

Recirculation The recir culation feature can be selected with the mode control knob. Y ou may choose be- tween Bi-Level Recirculation and Panel Recir- culation air outlets while in this mode. Nor- mally , air enters fr om outside the vehicle. However , when in Recirculation mode air inside the vehicle is re-used. Use this mode to rapidly cool the i[...]

NOTE: The numbers on the temperature dial repr esent a comfort setting when the Mode knob is set to AUTO, and not the actual air temperature. T urn the mode control (on the right) knob to AUTO, and then turn the blower control (on the left) knob to either LO AUTO or HI AUTO. The LO AUTO position should be used for front seat occupants only . The HI[...]

respectively . W ith the temperature setting in these posi- tions, the system does not attempt automatic comfort control. Air Conditioning The air conditioning in this system is automatic. Pressing this button while in AUTO mode will cause the LED to flash three times and remain off. This indicates that the system is in AUT O and requesting the air[...]

• Most of the time, when in Automatic operation, you can temporarily put the system into Recirculation mode by pressing the Recirculation button. However , under certain conditions in automatic the system is blowing air out of the defrost vents. When these conditions are present, and the Recirculation button is pressed, the indicator will flash a[...]

228 UNDERST ANDING YOUR INSTRUMENT P ANEL I n f o r m a t i o n P r o v i d e d b y :[...]

NOTE: Regardless of the type of operation, when a temperature knob is set to the full clockwise or full counterclockwise position, the system will deliver full hot or full cold air out of the ducts, respectively . The operator can override the AUTO mode setting and select the direction of the air by rotating the right mode knob to one of the follow[...]

Bi-Level Air flows both through the outlets located in the instrument panel and those located on the floor . Air flows through the registers in the back of the center console, and under the front seats to the rear seat passengers. These registers can be closed to block airflow . The center console outlets deliver conditioned air while the floor out[...]

defrost/floor modes. Attempting to use Recirculation while in these modes will cause the LED in the button to blink and then turn off. Operating Tips W indow Fogging W indows will fog on the inside when the humidity inside the vehicle is high. This often occurs in mild or cool temperatures when it’s rainy or humid. In most cases, turning the air [...]

When stopped in heavy traffic, it may be necessary to shift into NEUTRAL and press the accelerator slightly for fast idle operation to increase coolant flow and fan speed. Y our air conditioning system is also equipped with an automatic recir culation system. When the system senses a heavy load or high heat conditions, it may use partial Recirculat[...]

Operating Tips Chart 4 UNDERST ANDING YOUR INSTRUMENT P ANEL 233 I n f o r m a t i o n P r o v i d e d b y :[...]

I n f o r m a t i o n P r o v i d e d b y :[...]

ST ARTING AND OPERA TING CONTENTS 䡵 Starting Procedur es .................... 2 4 0 ▫ Normal Starting ..................... 2 4 0 ▫ Extreme Cold W eather (Below ⫺ 20°F Or ⫺ 29°C) ............... 2 4 1 ▫ If Engine Fails T o Start ................ 2 4 1 ▫ After Starting ....................... 2 4 2 䡵 Engine Block Heater — If Equi[...]

▫ Quadra-T rac II 威 Operating Instructions/ Precautions – If Equipped .............. 2 5 3 ▫ Shift Positions ...................... 2 5 5 ▫ Shifting Procedur es ................... 2 5 5 ▫ Quadra-Drive 威 II System – If Equipped .... 2 5 8 䡵 On-Road Driving T ips .................. 2 5 8 䡵 Off-Road Driving T ips .................[...]

▫ Hill Start Assist (HSA) – Four-Wheel Drive Models W ith NV245 T wo–Speed T ransfer Case Only ......................... 2 7 8 ▫ Hill Descent Control (HDC) – Four-Wheel Drive Models W ith NV245 T wo–Speed T ransfer Case Only ................... 2 8 1 ▫ ESP/BAS W arning Light And ESP/TCS Indicator Light ...................... 2 8 3 䡵[...]

▫ General Information .................. 3 1 4 䡵 Fuel Requirements ..................... 3 1 5 ▫ 3.7 Engine ......................... 3 1 5 ▫ 5.7L Engine ........................ 3 1 5 ▫ Reformulated Gasoline ................ 3 1 6 ▫ Gasoline/Oxygenate Blends ............. 3 1 6 ▫ E-85 Usage In Non-Flex Fuel V ehicles ...... 3 1 6 ▫[...]

▫ T owing – T wo-Wheel Drive Models ....... 3 3 8 ▫ T owing — Quadra-T rac I 威 (Single-Speed T ransfer Case) Four-Wheel Drive Models . . . 339 ▫ T owing — Quadra–T rac II 威 /Quadra–Drive 威 II Four-Wheel Drive Models ............. 3 3 9 5 ST ARTING AND OPERA TING 239 I n f o r m a t i o n P r o v i d e d b y :[...]

ST ARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust the inside and outside mirrors, fasten your seat belt, and if present, instruct all other occupants to buckle their seat belts. W ARNING! • Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or o[...]

Extreme Cold Weather (Below ⫺ 20°F or ⫺ 29°C) T o ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (avail- able from your authorized dealer) is recommended. If Engine Fails to Start W ARNING! • Never pour fuel or other flammable liquids into the throttle body air inlet opening in an a[...]

release it as soon as the starter engages. The starter motor will disengage automatically in 10 seconds. Once this occurs, release the accelerator pedal, turn the ignition switch to the LOCK position, wait 10 to 15 seconds, then repeat the “Normal Starting” procedure. CAUTION! T o prevent damage to the starter , wait 10 to 15 sec- onds before t[...]

AUTOMA TIC TRANSMISSION CAUTION! Damage to the transmission may occur if the follow- ing precautions are not observed: • Shift into P ARK only after the vehicle has come to a complete stop. • Shift into or out of REVERSE only after the vehicle has come to a complete stop and the engine is at idle speed. • Do not shift from REVERSE, P ARK, or [...]

Brake/T ransmission Shift Interlock System This vehicle is equipped with a Brake T ransmission Shift Interlock System (BTSI) that holds the shift lever in the P ARK position when the ignition switch is in the LOCK position. T o move the shift lever out of the P ARK position, the ignition switch must be turned to the ON or ST AR T position (engine r[...]

6. Move the shift lever into the NEUTRAL position. 7. The vehicle may then be started in NEUTRAL. Have your vehicle inspected by your local authorized dealer if the shift lock manual override has been used. Five–Speed Automatic T ransmission The electr onically-controlled transmission provides a precise shift schedule. The transmission electronic[...]

W ARNING! (Continued) • It is dangerous to move the shift lever out of P ARK or NEUTRAL if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse. Y ou could lose control of the vehicle and hit someone or something. Only shift into gear when the engine [...]

shifts the transmission into ERS 3 (third gear), the trans- mission will never shift above third gear , but can shift down to 2 (second) or 1 (first), when needed. NOTE: • If you pull and hold (not tap) the shift lever to the left (-), the transmission will downshift to the lowest gear that can be attained without overrevving the engine. The disp[...]

gear). When in the DRIVE position in fifth gear , the first tap to the left (-) will downshift the transmission and display 5 (ERS 5 is the same as normal fourth gear). Another tap to the left (-) will shift the transmission down to ERS 4 (direct gear). W ARNING! Do not downshift for additional engine braking on a slippery surface. The drive wheels[...]

• transmission has reached normal operating temperature. NOTE: If the vehicle is started in extremely cold tem- peratures, the transmission may not shift into Overdrive and will automatically select the most desirable gear for operation at this temperature. Normal operation will resume when the transmission fluid temperature has risen to a suitab[...]

performance and reduce the potential for transmission overheating or failure due to excessive shifting. When operating in TOW/HAUL mode, the transmission will shift into direct gear and Overdrive will be enabled under steady cruise conditions. The “TOW/HAUL Indicator Light” will illuminate in the instrument cluster to indicate when the switch h[...]

3. T urn the engine off, and be sure to turn the ignition switch to the LOCK position. 4. W ait approximately 10 seconds, then restart the en- gine. 5. Move the shift lever to the desired gear range. If the problem is no longer detected, the transmission will return to normal operation. If the problem persists, P ARK, REVERSE, and NEUTRAL will cont[...]

the transmission may not shift into the top Overdrive gear (normal fifth gear) until the transmission fluid and engine coolant are warm. • If the vehicle has not been driven in several days, the first few seconds of operation after shifting the trans- mission into gear may seem sluggish. This is due to the fluid partially draining from the torque[...]

CAUTION! When “rocking” a stuck vehicle by moving between “First” and REVERSE, do not spin the wheels faster than 15 mph (24 km/h) or drivetrain damage may result. FOUR-WHEEL DRIVE OPERA TION Quadra-T rac I 姞 Operating Instructions/ Precautions – If Equipped The Quadra-T rac I 威 is a single-speed (HI range only) transfer case, which p[...]

When additional traction is required, the 4WD LOW position can be used to lock the front and r ear driveshafts together and force the front and rear wheels to rotate at the same speed. The 4WD LOW position is intended for loose, slippery road surfaces only . Driving in the 4WD LOW position on dry , hard-surfaced roads may cause increased tire wear [...]

Shift Positions For additional information on the appr opriate use of each transfer case mode position, see the information below: 4WD HI This range is used on surfaces such as ice, snow , gravel, sand, and dry hard pavement. NEUTRAL This range disengages both the front and r ear driveshafts from the powertrain. It is to be used for flat towing beh[...]

NOTE: If shift conditions/interlocks are not met, or a transfer case motor temperature protection condition exists, a “CHECK SHIFT PROCEDURES” message will flash from the Electronic V ehicle Information Center (EVIC). Refer to “Elec- tronic V ehicle Information Center (EVIC)” in “Understand- ing Y our Instrument Panel” for further infor[...]

• Shifting into or out of 4WD LOW is possible with the vehicle completely stopped; however , difficulty may occur due to the mating clutch teeth not being prop- erly aligned. Several attempts may be requir ed for clutch teeth alignment and shift completion to occur . The preferr ed method is with the vehicle rolling 0 to 3 mph (0 to 5 km/h). If t[...]

NOTE: If shift conditions/interlocks are not met, a “CHECK SHIFT PROCEDURES” message will flash from the Electronic V ehicle Information Center (EVIC). Refer to “Electronic V ehicle Information Center (EVIC)” in “Understanding Y our Instrument Panel” for further information. Quadra-Drive 姞 II System – If Equipped The optional Quadra[...]

turns or abrupt maneuvers. As with other vehicles of this type, failur e to operate this vehicle correctly may result in loss of control or vehicle rollover . OFF-ROAD DRIVING TIPS NOTE: Prior to off-road driving, remove the front air dam to prevent damage. The front air dam is attached to the lower front fascia with quarter turn fasteners and can [...]

entering. Proceed with caution and maintain a steady controlled speed less than 5 mph (8 km/h) in deep water to minimize wave effects. Flowing W ater If the water is swift flowing and rising (as in storm run-of f), avoid crossing until the water level recedes and/or the flow rate is reduced. If you must cross flowing water avoid depths in excess of[...]

A void abrupt downshifts on icy or slippery roads, be- cause engine braking may cause skidding and loss of control. Hill Climbing NOTE: Before attempting to climb a hill, determine the conditions at the crest and/or on the other side. Before climbing a steep hill, shift the transmission to a lower gear and shift the transfer case to 4WD LOW . Use f[...]

T raction Downhill Shift the transmission into a low gear , and the transfer case into 4WD LOW range. Let the vehicle go slowly down the hill with all four wheels turning against engine compression drag. This will permit you to control the vehicle speed and direction. When descending mountains or hills, repeated braking can cause brake fade with lo[...]

W ARNING! Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking. Y ou might not have full braking power when you need it to prevent an accident. If you have been operating your vehicle in dirty conditions, get your brakes checked and cleaned as necessary . • If you experience unusual vibration after driving[...]

W ARNING! Continued operation with reduced power steering assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible. CAUTION! Prolonged operation of the steering system at the end of the steering wheel travel will increase the steering fluid temperature and it should be avoided when possible. Damage to t[...]

Checking the power steering fluid level at a defined service interval is not required. The fluid should only be checked if a leak is suspected, abnormal noises are apparent, and/or the system is not functioning as antici- pated. Coordinate inspection efforts through an autho- rized dealer . W ARNING! Fluid level should be checked on a level surface[...]

The parking brake lever is located in the center console. T o apply the parking brake, pull the lever up as firmly as possible. T o release the parking brake, pull the lever up slightly , press the center button, then lower the lever completely . When the parking brake is applied with the ignition switch in the ON position, the “Brake W arning Li[...]

W ARNING! • Never use the P ARK position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle movement and possible injury or damage. • Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be ser[...]

ANTI-LOCK BRAKE SYSTEM The Anti-Lock Brake System (ABS) is designed to aid the driver in maintaining vehicle control under adverse braking conditions. The system operates with a separate computer to modulate hydraulic pressure, to prevent wheel lock-up and help avoid skidding on slippery surfaces. All vehicle wheels and tires must be the same size [...]

W ARNING! (Continued) • The ABS cannot prevent the natural laws of phys- ics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that af- forded by the condition of the vehicle brakes and tires or the traction afforded. • The ABS cannot prevent accidents, including those resulting from excessive speed in turns,[...]

• Engines may idle at higher speeds during warm-up, which could cause rear wheels to spin and result in loss of vehicle control. Be especially careful while driving on slippery roads, in close-quarter maneuver- ing, parking, or stopping. • Do not drive too fast for road conditions, especially when roads are wet or slushy . A wedge of water can [...]

W ARNING! The ABS cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. The ABS cannot prevent accidents, including those re- sulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning. Only a safe, attentive, and skillful driver[...]

benefit of the system, you must apply continuous brak- ing pressur e during the stopping sequence (do not “pump” the brakes). Do not reduce brake pedal pressure unless braking is no longer desired. Once the brake pedal is released, the BAS is deactivated. W ARNING! The BAS cannot prevent the natural laws of physics from acting on the vehicle, n[...]

NOTE: Anytime the ESP system is in the “Full Off” mode, ERM is disabled. Refer to “Electronic Stability Program (ESP)” for a complete explanation of the avail- able ESP modes. W ARNING! Many factors, such as vehicle loading, road condi- tions and driving conditions, influence the chance that wheel lift or rollover may occur . ERM cannot pre[...]

• Understeer - when the vehicle is turning less than appropriate for the steering wheel position. The “ESP/TCS Indicator Light” located in the instrument cluster will start to flash as soon as the tires lose traction and the ESP system becomes active. The “ESP/TCS Indicator Light” also flashes when the TCS is active. If the “ESP/TCS Ind[...]

High Range (Four-Wheel Drive Models) or T wo-Wheel Drive Models On This is the normal operating mode for ESP in 4WD HIGH range and in two-wheel drive vehicles. Whenever the vehicle is started or the transfer case (if equipped) is shifted from 4WD LOW range or NEUTRAL back to 4WD HIGH range, the ESP system will be in this “On” mode. This mode sh[...]

NOTE: T o improve the vehicle’s traction when driving with snow chains, or starting off in deep snow , sand, or gravel, it may be desirable to switch to the “Partial Off” mode by pressing the “ESP OFF” switch. Once the situation r equiring ESP to be switched to the “Partial Off” mode is overcome, turn ESP back on by momentarily pressi[...]

in the P ARK position from any other position, and then moved out of the P ARK position. This will occur even if the message was previously cleared. W ARNING! W ith the ESP switched off, the enhanced vehicle stability offered by ESP and ERM are unavailable. In an emergency evasive maneuver , the ESP and ERM systems will not engage to assist in main[...]

W ARNING! W ith the ESP switched off, the enhanced vehicle stability offered by ESP and ERM are unavailable. In an emergency evasive maneuver , the ESP and ERM systems will not engage to assist in maintaining stability . The “Full Off” mode is intended for off- road use only . T railer Sway Control (TSC) TSC uses sensors in the vehicle to recog[...]

period of time after the driver takes their foot off of the brake pedal. If the driver does not apply the throttle during this short period of time, the system will release brake pr essur e and the vehicle will r oll down the hill. The system will release brake pressure in proportion to the amount of throttle applied as the vehicle starts to move i[...]

W ARNING! • If you use a trailer brake controller with your trailer , your trailer brakes may be activated and deactivated with the brake switch. If so, when the brake pedal is released, there may not be enough brake pressure to hold the vehicle and trailer on a hill and this could cause a collision with another vehicle or object behind you. In o[...]

Hill Descent Control (HDC) – Four-Wheel Drive Models With NV245 T wo–Speed T ransfer Case Only HDC maintains vehicle speed while descending hills during off-road driving situations and is available in 4WD LOW range only . T o enable HDC (transfer case must be in 4WD LOW range), press the HDC switch. If the HDC switch is pressed when the vehicle[...]

When HDC is properly enabled, the message “HILL DESCENT CONTROL” will appear in the EVIC and the light in the switch will be illuminated. HDC will auto- matically apply the brakes to control downhill speed when necessary . HDC has the capability to sense terrain and will only activate when the vehicle is descending a hill. It will usually not a[...]

HDC is intended for low speed off-road driving only . At vehicle speeds above 30 mph (48 km/h), HDC will no longer function. When the vehicle speed drops below 30 mph (48 km/h), HDC function will automatically resume and the vehicle speed will r eturn to the chosen set speed. W ARNING! HDC is only intended to assist the driver in control- ling vehi[...]

NOTE: • The “ESP/TCS Indicator Light” and the “ESP/BAS W arning Light” come on momentarily each time the ignition switch is turned to the ON position. • Each time the ignition switch is turned to the ON position, the ESP System will be ON even if it was previously turned off. • The ESP Contr ol System will make buzzing or clicking sou[...]

NOTE: • P (Passenger) - Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designa- tion. Example: P215/65R15 95H. • European-Metric tire sizing is based on European design standards. T ires designed to this standard have the tire size molded into the sidewall[...]

T ire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ ....blank.... ⴖ = Passenger car tire based on European design standards LT = Light truck tire based on U.S. design standards T = T emporary spare tire 31 = Overall diameter in inches (in) 215 = Section width in millimeters (mm) 65 = Aspect[...]

EXAMPLE: Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — The maximum speed corresponding to the speed symbol should only be a[...]

Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire, however , the date code may only be on one side. T ir es with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle[...]

Tire T erminology and Definitions T erm Definition Accessory W eight This means the combined weight of optional accessories. Some examples of optional accessories are automatic transmission, power steering, power brakes, power windows, power seats, and air conditioning. Air Pressure The amount of air inside the tire pressing outward on each square [...]

T erm Definition Light T ruck (L T -Metric) T ire A tire used on light duty trucks and some multipurpose passen- ger vehicles. Maximum Inflation Pressure The maximum air pressur e to which a cold tire can be inflated. The maximum air pressur e is molded onto the sidewall. Maximum Load Rating The load rating for a tire at the maximum permissible inf[...]

T erm Definition Rim A metal support for a tire and upon which the beads are seated. Sidewall The portion of a tire between the tread and the bead. T read The portion of a tire that comes into contact with the road. T readwear Indicators Narrow bands, sometimes called wear bars, that show across the tread of a tire when only 1/16 inch (1.6 mm) of t[...]

T ire and Loading Information Placard This placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) total weight your vehicle can carry 3) tire size designed for your vehicle 4) cold tire inflation pressures for the front, rear , and spare tires. Loading The vehicle maximum load on the tire must n[...]

XXX kg” on the T ire and Loading Information placard. The combined weight of occupants, cargo/luggage and trailer tongue weight (if applicable) should never exceed the weight refer enced here. Steps for Determining Correct Load Limit 1. Locate the statement “The combined weight of occu- pants and cargo should never exceed XXX lbs or XXX kg” o[...]

294 ST ARTING AND OPERA TING I n f o r m a t i o n P r o v i d e d b y :[...]

W ARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMA TION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory op[...]

W ARNING! (Continued) • Unequal tire pressures from one side of the ve- hicle to the other can cause the vehicle to drift to the right or left. • Always drive with each tire inflated to the recom- mended cold tire inflation pressure. Economy Improper inflation pressur es can cause uneven wear patterns to develop across the tire tread. These abn[...]

CAUTION! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage it. Inflation pressures specified on the placard are always cold tire inflation pressur e. Cold tire inflation pressur e is defined as the tire pressure after the vehic[...]

Tire Pressures For High Speed Operation The manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important. Increased tire pressur e and reduced vehicle loading may be required for high-[...]

W ARNING! T emporary use spare tires are for emergency use only . W ith these tires, do not drive more than 50 mph (80 km/h). T emporary use spare tires have limited tread life. When the tread is worn to the tread wear indicators, the temporary use spare tire needs to be replaced. Be sure to follow the warnings, which apply to your spare. Failure t[...]

W ARNING! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure some- one. Do not spin your vehicle’s wheels faster than 30 mph (48 km/h) when you are stuck, and do not let anyone near a spinning wheel no matter what the speed. T read Wear Indicators [...]

Life of Tire The service life of a tire is dependent upon various factors including but not limited to: • Driving style • T ire pressur e • Distance driven W ARNING! T ires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. Y ou could lose[...]

W ARNING! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change sus- pension dimensions and performance characteris- tics, resulting in changes to steering, handling, and braking of your vehicle. This can cause unpredict- able handling and stress to steeri[...]

• Do not install tire chains or traction devices on ve- hicles with larger than P235/65R17 tir es. T ires lar ger than this may not provide sufficient body clearance with chains or other traction devices. • Use SAE class “S” tire chains or traction devices only . • Follow tir e chain manufacturer’s instructions for mounting chains. • [...]

The suggested rotation method is the “forward-cr oss” shown in the following diagram. TIRE PRESSURE MONITOR SYSTEM (TPMS) The T ire Pressur e Monitoring System (TPMS) will warn the driver of a low tire pressure based on the vehicle recommended cold tire pressur e. The tire pressure will vary with temperature by about 1 psi (7 kPa) for every 12?[...]

The TPMS will continue to warn the driver of low tire pressur e as long as the condition exists, and will not turn off until the tire pressure is at or above recommended cold tir e pressur e. Once the low tir e pr essur e warning has been illuminated, the tire pressur e must be increased to the recommended cold tire pressur e in order for the T ir [...]

CAUTION! • The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style. Aftermarket wheels can cause sensor dam- ag[...]

• Seasonal temperature changes will affect tire pressur e, and the TPMS will monitor the actual tire pressure in the tire. Base System The T ir e Pressure Monitor System (TPMS) uses wireless technology with wheel rim-mounted electr onic sensors to monitor tire pressur e levels. Sensors, mounted to each wheel as part of the valve stem, transmit ti[...]

pressur es have been received. The vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) to receive this information. The T ire Pressur e Monitoring T elltale Light will flash on and off for 75 seconds, and remain on solid when a system fault is detected. In addition, a “CHECK TPM SYSTEM” message will be displayed for 75 sec[...]

T ire Pressur e Monitoring T elltale Light as long as none of the road tires are below the low pressur e warning threshold. • If your vehicle is not equipped with a matching full-size spare wheel and tire assembly , it does not have a tir e pressur e monitoring sensor in the spare tire. The TPMS will not be able to monitor the tire pressur e. If [...]

NOTE: It is particularly important, for you to regularly check the tire pressur e in all of your tires and to maintain the proper pressure. The T ir e Pressur e Monitor System (TPMS) consists of the following components: • Receiver Module • Four T ire Pressur e Monitoring Sensors • Three T rigger Modules (mounted in three of the four wheel we[...]

NOTE: Y our system can be set to display pressur e units in PSI, kPa, or BAR. Should a low tire condition occur on any of the four active road tire(s), you should stop as soon as possible, and inflate the low tire(s) that is “flashing” on the graphic display to the vehicle’s recommended cold tire pressur e. The system will automatically updat[...]

NOTE: Y our system can be set to display pressur e units in PSI, kPa, or BAR. If the ignition switch is cycled, this sequence will repeat, providing the system fault still exists. If the system fault no longer exists, the T ire Pressur e Monitoring T elltale Light will no longer flash, the ⬙ CHECK TPM SYSTEM ⬙ message will not be present, and a[...]

case, the ⬙ CHECK TPM SYSTEM ⬙ message is then fol- lowed by a graphic display , with pressur e values still shown. This indicates the pressur e values are still being received from the TPM Sensors. However , the system still needs to be serviced as long as the ⬙ CHECK TPM SYSTEM ⬙ message exists. NOTE: • If your vehicle is equipped with [...]

SYSTEM ⬙ message for three seconds and then display dashes (- -) in place of the pressur e value. For each subsequent ignition switch cycle, a chime will sound, the T ire Pressur e Monitoring T elltale Light will flash on and off for 75 seconds and then remain on solid, and the EVIC will display a ⬙ CHECK TPM SYSTEM ⬙ message for thr ee secon[...]

FUEL REQUIREMENTS 3.7 Engine All engines (except 5.7L engines) are de- signed to meet all emissions regulations and provide excellent fuel economy and performance when using high-quality un- leaded “regular” gasoline having an oc- tane rating of 87. The use of premium gasoline is not recommended, as it will not provide any benefit over regular [...]

Reformulated Gasoline Many areas of the country requir e the use of cleaner burning gasoline r eferred to as “Reformulated Gasoline.” Reformulated gasoline contains oxygenates, and are spe- cifically blended to reduce vehicle emissions and im- prove air quality . The manufactur er supports the use of reformulated gaso- line. Properly blended re[...]

• OBD II “Malfunction Indicator Light” on • poor engine performance • poor cold start and cold drivability • increased risk for fuel system component corrosion T o fix a Non-FFV vehicle inadvertently fueled once with E-85 perform the following: • drain the fuel tank (see your authorized dealer) • change the engine oil and oil filter[...]

Materials Added T o Fuel All gasoline sold in the United States is requir ed to contain effective detergent additives. Use of additional detergents or other additives is not needed under normal conditions and would result in additional cost. Therefor e, you should not have to add anything to the fuel. Fuel System Cautions CAUTION! Follow these guid[...]

Carbon Monoxide W arnings W ARNING! Carbon monoxide (CO) in exhaust gases is deadly . Follow the precautions below to prevent carbon monoxide poisoning. • Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas which can kill. Never run the engine in a closed area, such as a garage, and never sit in a parked vehicl[...]

ADDING FUEL Fuel Filler Cap (Gas Cap) The gas cap is located behind the fuel filler door , on the driver’s side of the vehicle. If the gas cap is lost or damaged, be sur e the r eplacement cap is for use with this vehicle. CAUTION! • Damage to the fuel system or emission control system could result from using an improper fuel cap (gas cap). A p[...]

W ARNING! • Never have any smoking materials lit in or near the vehicle when the gas cap is removed or the tank filled. • Never add fuel when the engine is running. This is in violation of most state and federal fire regula- tions and will cause the malfunction indicator light to turn on. • A fire may result if gasoline is pumped into a porta[...]

VEHICLE LOADING Certification Label As required by National Highway T raf fic Safety Admin- istration regulations, your vehicle has a certification label affixed to the driver’s side door or B-Pillar . This label contains the month and year of manufacture, Gross V ehicle W eight Rating (GVWR), Gross Axle W eight Rating (GA WR) front and rear , an[...]

components, sometimes specified by purchasers for in- creased durability , does not necessarily increase the ve- hicle’s GVWR. T ire Size The tire size on the label represents the actual tire size on your vehicle. Replacement tires must be equal to the load capacity of this tire size. Rim Size This is the rim size that is appropriate for the tire[...]

heavier items down low and be sure that the weight is distributed equally . Stow all loose items securely before driving. Improper weight distributions can have an adverse affect on the way your vehicle steers and handles, and the way the brakes operate. CAUTION! Do not load your vehicle any heavier than the GVWR or the maximum front and rear GA WR[...]

Gross T railer W eight (GTW) The GTW is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or tem- porary) loaded in or on the trailer in its ⬙ loaded and ready for operation ⬙ condition. The recommended way to measure GTW is to put your fully loaded trailer on a vehicle scale. The entire weight of the [...]

W eight-Carrying Hitch A weight-carrying hitch supports the trailer tongue weight, just as if it were luggage located at a hitch ball or some other connecting point of the vehicle. These kind of hitches are the most popular on the market today and they are commonly used to tow small- and medium- sized trailers. W eight-Distributing Hitch A weight-d[...]

W ithout W eight-Distributing Hitch (Incorrect) W ith W eight-Distributing Hitch (Correct) 5 ST ARTING AND OPERA TING 327 I n f o r m a t i o n P r o v i d e d b y :[...]

T railer Hitch Classification Y our vehicle may be factory equipped for safe towing of trailers weighing over 3,500 lbs (1 587 kg) with the optional T railer T ow Prep Package. See your authorized dealer for package content. The following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and sho[...]

T railer Hitch Classification Definitions Class Max. T railer Hitch Industry Standards Class I - Light Duty 2,000 lbs (907 kg) Class II - Medium Duty 3,500 lbs (1 587 kg) Class III - Heavy Duty 5,000 lbs (2 268 kg) Class IV - Extra Heavy Duty 10,000 lbs (4 540 kg) Refer to the “T railer T owing W eights (Maximum T railer W eight Ratings)” chart[...]

T railer T owing Weights (Maximum T railer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/Model Model GCWR (Gross Com- bined Wt. Rating) Frontal Area Max. GTW (Gross T railer Wt.) Max. T railer T ongue Wt. (See Note) 3.7L 4x2 8,400 lbs (3 810 kg) 40 sq ft (3.72 sq m) 3,500 l[...]

T railer And T railer T ongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer . This places 10% to 15% of the Gross T railer W eight (GTW) on the tow hitch of your vehicle. Loads balanced over the wheels, or heavier in the rear , can cause the trailer to sway severely side-to-side which will cause loss of cont[...]

NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or authorized dealer-installed options, must be considered as part of the total load on your vehicle. Refer to “T ire Safety Information/T ir e and Loading Information Placard” in “Starting and Operat- ing”[...]

W ARNING! (Continued) • When hauling cargo or towing a trailer , do not overload your vehicle or trailer . Overloading can cause a loss of control, poor performance or dam- age to brakes, axle, engine, transmission, steering, suspension, chassis structure or tires. • Safety chains must always be used between your vehicle and trailer . Always co[...]

T owing Requirements – T ires − Do not attempt to tow a trailer while using a compact spare tire. − Proper tire inflation pressures are essential to the safe and satisfactory operation of your vehicle. Refer to “T ires – General Information” in “Starting and Oper- ating” for proper tire inflation procedur es. − Check the trailer t[...]

CAUTION! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity . Failure to do this could lead to accelerated brake lining wear , higher brake pedal effort, and longer stopping distances. W ARNING! • Do not connect trailer brakes to your vehicle’s hydraulic brake lines. [...]

The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector . Refer to the following illustrations. Four-Pin Connector 1 — Female Pins 4 — Park 2 — Male Pin 5 — Left Stop/T urn 3 — Ground 6 — Right Stop/T urn Seven-Pin Connector 1 — Battery 5 — Ground 2 — Backup Lamps 6 — Left [...]

T owing Tips Before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy traffic. Automatic T ransmission The DRIVE range can be selected when towing. How- ever , if frequent shifting occurs while in this range, the TOW/HAUL mode (if equipped), or a lower gear range, should be selected. NOTE: Using th[...]

Cooling System T o reduce potential for engine and transmission over- heating, take the following actions: − City Driving When stopped for short periods of time, shift the trans- mission into NEUTRAL and increase engine idle speed. − Highway Driving Reduce speed. − Air Conditioning T urn off temporarily . SNOW PLOW Snow plows, winches, and ot[...]

W ARNING! If the driveshaft is removed, the vehicle can roll even if the transmission is in P ARK, which could cause serious injury or death. The parking brake must be firmly engaged and the wheels chocked during driveshaft removal and installa- tion. The parking brake must remain engaged unless the vehicle is securely and properly connected to the[...]

W ARNING! Y ou or others could be injured if you leave the vehicle unattended with the transfer case in the NEUTRAL position without first fully engaging the parking brake. The transfer case NEUTRAL position disengages both the front and rear driveshafts from the powertrain and will allow the vehicle to move even if the transmission is in P ARK. Th[...]

Center). Refer to “Electronic V ehicle Information Center (EVIC)” in “Understanding Y our Instrument Panel” for further information. 5. Start the engine. 6. Shift the transmission into DRIVE. 7. Release the brake pedal and ensure that there is no vehicle movement. 8. T urn the engine off. 9. Shift the transmission into P ARK. 10. T urn the [...]

CAUTION! T ransmission damage may occur if the transmission is shifted into P ARK with the transfer case in NEU- TRAL and the engine running. W ith the transfer case in NEUTRAL ensure that the engine is OFF prior to shifting the transmission into P ARK (refer to steps 7 and 8 above). Shifting Out Of NEUTRAL Use the following procedure to prepar e y[...]

5. Shift the transmission into P ARK. 6. Start the engine. 7. Shift the transmission into DRIVE. NOTE: When shifting out of transfer case NEUTRAL, turning the engine OFF may be requir ed to avoid gear clash. CAUTION! Do not use a bumper-mounted clamp-on tow bar on your vehicle. The bumper face bar will be damaged. Neutral Switch 5 ST ARTING AND OPE[...]

I n f o r m a t i o n P r o v i d e d b y :[...]

WHA T T O DO IN EMERGENCIES CONTENTS 䡵 Hazard W arning Flashers ................ 3 4 6 䡵 If Y our Engine Overheats ................ 3 4 6 䡵 Jacking And T ire Changing ............... 3 4 8 ▫ Jack Location ....................... 3 4 8 ▫ Spare T ire Stowage ................... 3 4 9 ▫ Spare T ire Removal ................... 3 4 9 ▫ Pre[...]

HAZARD W ARNING FLASHERS The Hazard W arning flasher switch is located on the switch bank just above the climate controls. Press the switch to turn on the Hazard W arning flasher . When the switch is activated, all dir ectional turn signals will flash on and off to warn oncoming traffic of an emergency . Press the switch a second time to turn off t[...]

CAUTION! Driving with a hot cooling system could damage your vehicle. If the temperature gauge reads HOT (H), pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on HOT (H), and you hear continuous chimes, turn the engine off immediately and [...]

JACKING AND TIRE CHANGING W ARNING! • Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. Y ou could be crushed. Never get any part of your body under a vehicle that is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. • The jack i[...]

Spare Tire Stowage The spare tire is stowed under the rear of the vehicle by means of a cable winch mechanism. T o remove or stow the spare, use the jack handle to rotate the “spare tire drive” nut. The nut is located under a plastic cover at the center-r ear of the cargo floor area, just inside the liftgate opening. CAUTION! Do not use power t[...]

CAUTION! • The winch mechanism is designed for use with the jack extension tube only . Use of an air wrench or other power tools is not recommended and can damage the winch. • When the spare is clear , tilt the retainer at the end of the cable and pull it through the center of the wheel. Preparations for Jacking 1. Park the vehicle on a firm, l[...]

Jacking Instructions W ARNING! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • Always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle. • Block the wheel diagonally opposite the wheel to be raised. • Set the parking brake firmly [...]

1. Remove the spare tire, jack, and tools from storage. 2. Loosen (but do not remove) the wheel lug nuts by turning them to the left, one turn, while the wheel is still on the ground. 3. Assemble the jack and jacking tools as shown. Connect jack handle driver (1) to two extensions (2) then to the lug wrench (3). 4. Locate the jack as shown. For the[...]

For the r ear axle, place it under the axle near the wheel to be changed. Ensure the jack is closest to the inside of the wheel when jacking on the rear axle. Do not raise the vehicle until you are sure the jack is fully engaged. 5. Raise the vehicle by turning the jack screw clockwise. Raise the vehicle only until the tire just clears the surface [...]

W ARNING! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 6. Remove the lug nuts and wheel. 7. Position the spar e wheel/tir e on the vehicle and install the lug nuts with the cone-shaped end toward the wheel. Lightly t[...]

Double check to ensure the tire is snug against the underbody of the vehicle. Damage to the winch cable may result if the vehicle is driven with the tire loose. W ARNING! Do not use power tools to winch the tire up or down. Impact-type tools may damage the winch mecha- nism. 12. Reinstall the plastic plug into the floor of the cargo area. JUMP-ST A[...]

Preparations for Jump-Start The battery in your vehicle is located in the front of the engine compartment, behind the left headlight assembly . W ARNING! • T ake care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is on. Y ou can be injured by moving fan blades. • Remove any metal jewel[...]

3. If using a another vehicle to jump-start the battery , park the vehicle within the jumper cables reach, set the parking brake and make sure the ignition is OFF . W ARNING! Do not allow vehicles to touch each other as this could establish a ground connection and personal injury could result. Jump-Starting Procedure W ARNING! Failure to follow thi[...]

W ARNING! Do not connect the cable to the negative post (-) of the discharged battery . The resulting electrical spark could cause the battery to explode and could result in personal injury . 5. Start the engine in the vehicle that has the booster battery , let the engine idle a few minutes, and then start the engine in the vehicle with the dischar[...]

EMERGENCY TOW HOOKS — IF EQUIPPED If your vehicle is equipped with tow hooks, there will be one in the rear and two mounted on the front of the vehicle. The rear hook will be located on the driver’s side of the vehicle. NOTE: For off-r oad recovery , it is recommended to use both of the front tow hooks to minimize the risk of damage to the vehi[...]

If the transmission is not operable, or the vehicle must be towed faster than 30 mph (48 km/h) or farther than 15 miles (24 km), remove the driveshaft or tow with all four wheels OFF the ground. Acceptable methods are to tow the vehicle on a flatbed, or with one end of the vehicle raised and the other end on a towing dolly . Four-Wheel Drive Models[...]

MAINT AINING YOUR VEHICLE CONTENTS 䡵 Engine Compartment – 3.7L .............. 3 6 3 䡵 Engine Compartment – 5.7L .............. 3 6 4 䡵 Onboard Diagnostic System – OBD II ....... 3 6 5 ▫ Loose Fuel Filler Cap Message ........... 3 6 5 䡵 Emissions Inspection And Maintenance Programs ............................ 3 6 6 䡵 Replacement P[...]

▫ Brake System ....................... 3 8 5 ▫ Front/Rear Axle Fluid ................. 3 8 7 ▫ T ransfer Case ....................... 3 8 8 ▫ Automatic T ransmission ............... 3 8 9 ▫ Maintenance After Off-Road Driving ...... 3 9 2 ▫ Appearance Care And Protection From Corrosion .......................... 3 9 3 䡵 Fuses .........[...]

ENGINE COMP ARTMENT – 3.7L 1 — Engine Coolant Reservoir 6 — W asher Fluid Reservoir 2 — Engine Oil Dipstick 7 — Battery 3 — Brake Fluid Reservoir 8 — Engine Oil Fill 4 — Power Distribution Center 9 — Coolant Pressure Cap 5 — Integrated Power Module 10 — Air Cleaner Filter 7 MAINT AINING YOUR VEHICLE 363 I n f o r m a t i o n P[...]

ENGINE COMP ARTMENT – 5.7L 1 — Engine Coolant Reservoir 7 — W asher Fluid Reservoir 2 — Automatic T ransmission Dipstick 8 — Battery 3 — Engine Oil Fill 9 — Engine Oil Dipstick 4 — Brake Fluid Reservoir 10 — Coolant Pressure Cap 5 — Power Distribution Center 1 1 — Air Cleaner Filter 6 — Integrated Power Module 364 MAINT AINI[...]

ONBOARD DIAGNOSTIC SYSTEM – OBD II Y our vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly , your vehicle will provide excellent performance and fuel economy , as well[...]

gas cap until a ⬙ clicking ⬙ sound is heard. This is an indication that the gas cap is properly tightened. The message will remain displayed until the vehicle diagnostic system can retest the fuel system. The test will perform the next time the vehicle is started, if the vehicle was keyed off above 40°F (4°C) outside temperature and the follo[...]

Y our vehicle has a simple ignition key-actuated test, which you can use prior to going to the test station. T o check if your vehicle’s OBD II system is ready , you must do the following: 1. T urn the ignition switch to the ON position, but do not crank or start the engine. 2. If you crank or start the engine, you will have to start this test ov[...]

REPLACEMENT P ARTS Use of genuine MOP AR 威 parts for normal/scheduled maintenance and repairs is highly recommended to en- sure the designed performance. Damage or failures caused by the use of non-MOP AR 威 parts for maintenance and repairs will not be covered by the manufacturer’s warranty . DEALER SERVICE Y our authorized dealer has the qua[...]

CAUTION! • Failure to properly maintain your vehicle or per- form repairs and service when necessary could result in more costly repairs, damage to other components or negatively impact vehicle perfor- mance. Immediately have potential malfunctions examined by an authorized Chrysler Group LLC dealership or qualified repair center . • Y our vehi[...]

CAUTION! Overfilling or underfilling the crankcase will cause aeration or loss of oil pressure. This could damage your engine. Change Engine Oil The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Refer to “Maintenance Schedule” for further information. NOTE: Under no circumstances [...]

Engine Oil V iscosity (3.7L and 5.7L Engines) SAE 5W -20 engine oil is recommended for all operating temperatures. This engine oil improves low temperature starting and vehicle fuel economy . The engine oil filler cap also shows the recommended engine oil viscosity for your vehicle. For information on engine oil filler cap location, refer to “Eng[...]

Engine Oil Filter The engine oil filter should be replaced with a new filter at every oil change. Engine Oil Filter Selection The manufacturer’s engines have a full-flow type dispos- able oil filter . Use a filter of this type for replacement. The quality of replacement filters varies considerably . Only high-quality filters should be used to ass[...]

Engine Air Cleaner Filter Selection The quality of replacement engine air cleaner filters varies considerably . Only high quality filters should be used to assure most efficient service. MOP AR 威 engine air cleaner filters are a high quality filter and are recommended. Maintenance-Free Battery Y our vehicle is equipped with a maintenance-fr ee ba[...]

CAUTION! • It is essential when replacing the cables on the battery that the positive cable is attached to the positive post, and the negative cable is attached to the negative post. Battery posts are marked (+) positive and (-) negative and identified on the battery case. • If a “fast charger” is used while battery is in the vehicle, disco[...]

W ARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air condi- tioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. Refer to W arranty Information Book, located on t[...]

hood latching components to ensure proper function. When performing other underhood services, the hood latch, release mechanism and safety catch should be cleaned and lubricated. The external lock cylinders should be lubricated twice a year , preferably in the Fall and Spring. Apply a small amount of a high quality lubricant, such as MOP AR 威 Loc[...]

located in the engine compartment, be sure to check the fluid level at regular intervals. Fill the reservoir with windshield washer solvent only (not radiator antifreeze). When refilling the washer fluid reservoir , take some washer fluid and apply it to a cloth or towel and wipe clean the wiper blades, this will help blade performance. T o prevent[...]

W ARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. T o avoid breathing CO, refer to “Safety T ips/Exhaust Gas” in “Things T o Know Before Starting Y our V ehicle” for further informa- tion. CAUTION! The catalytic[...]

NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you. W ARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system. Do not park or operate your vehicle in areas where your e[...]

Cooling System W ARNING! Y ou or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator . If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool. Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot. Engine Coolant Che[...]

Cooling System — Drain, Flush, and Refill If the engine coolant (antifreeze) is dirty and contains a considerable amount of sediment, clean and flush with reliable cooling system cleaner . Follow with a thorough rinsing to remove all deposits and chemicals. Properly dispose of the old engine coolant (antifreeze). Refer to “Maintenance Schedule?[...]

CAUTION! (Continued) • This vehicle has not been designed for use with Propylene Glycol-based engine coolant (anti- freeze). Use of Propylene Glycol-based engine coolant (antifreeze) is not recommended. Adding Coolant Y our vehicle has been built with an improved engine coolant (antifreeze) that allows extended maintenance intervals. This engine [...]

NOTE: Mixing engine coolant (antifreeze) types will decrease the life of the engine coolant (antifreeze) and will require more frequent engine coolant (antifreeze) changes. Cooling System Pressure Cap The cap must be fully tightened to prevent loss of engine coolant (antifreeze), and to ensure that engine coolant (antifreeze) will return to the rad[...]

Disposal of Used Engine Coolant Used ethylene glycol-based engine coolant (antifreeze) is a regulated substance requiring pr oper disposal. Check with your local authorities to determine the disposal rules for your community . T o prevent ingestion by ani- mals and children, do not store ethylene glycol-based engine coolant (antifreeze) in open con[...]

If an examination of your engine compartment shows no evidence of radiator or hose leaks, the vehicle may be safely driven. The vapor will soon dissipate. • Do not overfill the coolant recovery bottle. • Check engine coolant (antifreeze) freeze point in the radiator and in the coolant recovery bottle. If engine coolant (antifreeze) needs to be [...]

W ARNING! Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear , and possible brake damage. Y ou would not have your full braking capacity in an emergency . Fluid Level Check — Brake Master Cylinder [...]

W ARNING! (Continued) • T o avoid contamination from foreign matter or moisture, use only new brake fluid or fluid that has been in a tightly closed container . Keep the master cylinder reservoir cap secured at all times. Brake fluid in a open container absorbs moisture from the air resulting in a lower boiling point. This may cause it to boil un[...]

Selection of Lubricant Use only the manufacturer’s recommended fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintain- ing Y our V ehicle” for further information. T ransfer Case Fluid Level Check Inspect the transfer case for fluid leaks. If a fluid leak is found, the transfer case fluid level can be checked by removing the[...]

Automatic T ransmission Selection of Lubricant It is important that the proper lubricant is used in the transmission to assure optimum transmission perfor- mance. Use only the manufactur er’s r ecommended trans- mission fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Y our V ehicle” for further informa- tion. It is[...]

CAUTION! Do not use chemical flushes in your transmission as the chemicals can damage your transmission compo- nents. Such damage is not covered by the New V ehicle Limited W arranty . Fluid Level Check (3.7L Engine) Regular fluid level checks are not required. For this reason, the dipstick is omitted. If you notice fluid loss or transmission slipp[...]

Fluid Level Check (5.7L Engine) Check the fluid level while the transmission is at normal operating temperature. This occurs after at least 15 miles (25 km) of driving. At normal operating temperature the fluid cannot be held comfortably between the fingertips. T o check the fluid level properly , the following procedur e must be used: 1. Operate t[...]

CAUTION! Be aware that if the fluid temperature is below 50°F (10°C) it may not register on the dipstick. Do not add fluid until the temperature is elevated enough to produce an accurate reading. 7. Check for leaks. Release parking brake. T o prevent dirt and water from entering the transmission after checking or r eplenishing fluid, make certain[...]

CAUTION! Under frequent heavy-duty driving conditions, change all lubricants, and lubricate body compo- nents, all driveline joints and steering linkage more often than in normal service, to prevent excessive wear . Appearance Care and Protection from Corrosion Protection of Body and Paint from Corrosion V ehicle body care requirements vary accordi[...]

• If insects, tar , or other similar deposits have accumu- lated on your vehicle, use MOP AR 威 Super Kleen Bug and T ar Remover or equivalent to remove. • Use a high quality cleaner wax, such as MOP AR 威 Cleaner W ax to remove road film, stains, and to protect your paint finish. T ake car e never to scratch the paint. • A void using abras[...]

• If your vehicle is damaged due to an accident or similar cause which destroys the paint and protective coating, have your vehicle repair ed as soon as pos- sible. The cost of such repairs is consider ed the respon- sibility of the owner . • If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., assure that such materia[...]

• Blot any remaining stain with a clean, damp towel. • For tough stains, apply MOP AR 威 T otal Clean or a mild soap solution to a clean, damp cloth and remove the stain. Use a fr esh, damp towel to remove soap residue. • For grease stains, apply MOP AR 威 Multi-Purpose Cleaner or equivalent to a clean, damp cloth and remove the stain. Use [...]

W ARNING! Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in closed areas, they may cause respiratory harm. Cleaning Headlights Y our vehicle has plastic headlights that are lighter and less susceptible to stone breakage than glass headlights. Plastic is not as scratch-resistant as glass and therefor [...]

2. Dry with a soft tissue. Seat Belt Maintenance Do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage will also weaken the fabric. If the belts need cleaning, use MOP AR 威 T otal Clean, a mild soap solution, or lukewarm water . Do not remove the belts from the vehicle to wash t[...]

Cavity Cartridge Fuse Mini- Fuse Description 3 10 Amp Red Htd Mirror (EBL) 4 20 Amp Y ellow Rr Pwr Out (B+) 5 10 Amp Red Rr HV AC (R/O) (Commander Only) 6 Spare (B+) 7 20 Amp Y ellow Door Locks (B+) 8 Spare (B+) 9 20 Amp Y ellow Pwr Outlet (B+) Cavity Cartridge Fuse Mini- Fuse Description 10 10 Amp Red Final Drive Control Module (FDCM), Heater V en[...]

Cavity Cartridge Fuse Mini- Fuse Description 14 20 Amp Y ellow Cigar Ltr (R/A) 15 10 Amp Red T ire Pressur e T ran- sponders (R/O) 16 10 Amp Red Upper & Lower Switch Bank, Diag. Connector , Cluster (B+) 17 15 Amp Blue Flipper Glass (B+) 19 Spare (R/S) 20 10 Amp Red Steering Column Control Module (SCCM), Cluster (R/ S), BUX T railer T ow Cavity [...]

Underhood Fuses (Power Distribution Center) Cavity Cartridge Fuse Mini- Fuse Description 1 50 Amp Red PTC Heater 1 (Diesel Only) Cavity Cartridge Fuse Mini- Fuse Description 2 40 Amp Green HID Headlamps 3 50 Amp Red PTC Heater 2 (Diesel Only) 4 30 Amp Pink Power Outlets 5 50 Amp Red PTC Heater 3 (Diesel Only) 6 30 Amp Pink Cig Lighter , T rail T ow[...]

Cavity Cartridge Fuse Mini- Fuse Description 1 1 40 Amp Green HV AC Blower 12 30 Amp Pink Rear W iper , Ign R/O 13 40 Amp Green Rear W indow De- froster (EBL)/Heated Mirror 14 30 Amp Pink Rear HV AC – If Equipped 15 — Spare 16 50 Amp Red ASD 17 30 Amp Pink ABS Pump 18 40 Amp Green Accessory Delay , Seats Cavity Cartridge Fuse Mini- Fuse Descrip[...]

Cavity Cartridge Fuse Mini- Fuse Description 27 20 Amp Y ellow HD W asher – If Equipped (Export Only) 28 30 Amp Green ABS V alves 29 20 Amp Y ellow PCM Batt (Gasoline Only) 30 — Spare 31 — Spare 32 15 Amp Blue Powertrain Control Module (Diesel Only) 33 20 Amp Y ellow Final Drive Control Module (FDCM) E-Diff 34 — Spare 35 20 Amp Y ellow T ra[...]

Underhood Fuses (Integrated Power Module) Cavity Cartridge Fuse Mini- Fuse Description 8 10 Amp Red Lt Park Lamps Cavity Cartridge Fuse Mini- Fuse Description 9 10 Amp Red T railer -T ow Park Lamps 10 10 Amp Red Rt Park Lamps 12 20 Amp Y ellow Front Control Module (FCM) Batt #4 13 20 Amp Y ellow Front Control Module (FCM) Batt #2 14 20 Amp Y ellow [...]

Cavity Cartridge Fuse Mini- Fuse Description 18 20 Amp Y ellow Front Control Module (FCM) Batt #1 19 20 Amp Y ellow Lt T railer -T ow Stop/ T urn 20 20 Amp Y ellow Front Control Module (FCM) Batt #3 21 20 Amp Y ellow Rt T railer -T ow Stop/ T urn 22 30 Amp Pink Final Drive Control Module (FDCM) MOD 23 50 Amp Red Radiator Fan Cavity Cartridge Fuse M[...]

VEHICLE STORAGE If you are leaving your vehicle dormant for more than 21 days you may want to take steps to protect your battery . Y ou may: • Remove fuse #27 in the Intelligent Power Module labeled Ignition-Off Draw (IOD#1). • Or , disconnect the negative cable from the battery . • Anytime you store your vehicle, or keep it out of service (i[...]

Exterior Lights Bulb T ype Backup Lamps ......................... 3157K Front Park/T urn Lamp ................... 3757A Front Fog Lamps ........................ 9145 Front Side Marker ...................... W 5 W Headlamps (Low Beam) – High Intensity Discharge (HID) .......... D 1 S (Ser viced at Authorized Dealer) Headlamps (Low Beam) ..........[...]

NOTE: On vehicles equipped with High Intensity Dis- charge (HID) headlamps, when the headlamps are turned on, there is a blue hue to the lamps. This dimin- ishes and becomes more white after approximately 10 seconds, as the system charges. Halogen Headlamps — If Equipped 1. Open the hood. 2. T urn the low or high beam bulb one–quarter turn coun[...]

CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. Front T urn Signal 1. Open the hood. 2. T urn the turn signal bulb one–quarter turn counter- clockwise to remove from housing. 3. Disconnect the electrica[...]

CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. Front Fog Lamp 1. Reach behind the front fascia from under the vehicle. 2. T urn the front fog lamp bulb one–quarter turn coun- terclockwise to remove fro[...]

3. Squeeze the socket assembly tabs to remove it fr om the housing. 4. Pull the bulb to remove it from the socket. 5. Replace the bulb, reinstall the socket, and reattach the lamp assembly . 1 — T ail/Stop Lamp Bulb 3 — Back-Up Lamp Bulb 2 — T ail/T urn Signal Bulb 7 MAINT AINING YOUR VEHICLE 411 I n f o r m a t i o n P r o v i d e d b y :[...]

Center High-Mounted Stop Lamp (CHMSL) 1. Remove the two screws securing the CHMSL. 2. T wist the bulb socket to remove from the CHMSL housing. 3. Pull the bulb out of the socket. 4. Replace the bulb, reinstall the socket and reattach the CHMSL. 412 MAINT AINING YOUR VEHICLE I n f o r m a t i o n P r o v i d e d b y :[...]

FLUID CAP ACITIES U.S. Metric Fuel (Approximate) 3.7L and 5.7L Engines 21 Gallons 79 Liters Engine Oil with Filter 3.7L Engine (SAE 5W -20, API Certified) 5 Quarts 4.7 Liters 5.7L Engine (SAE 5W -20, API Certified) 7 Quarts 6.6 Liters Cooling System * 3.7L Engine (MOP AR 威 Engine Coolant/Antifreeze 5–Y ear/100,000 Mile Formula or equivalent) ?[...]

FLUIDS, LUBRICANTS, AND GENUINE P ARTS Engine Component Fluid, Lubricant, or Genuine Part Engine Coolant MOP AR 威 Antifreeze/Coolant 5 Y ear/100,000 Mile Formula HOA T (Hy- brid Organic Additive T echnology) or equivalent. Engine Oil – 3.7L and 5.7L Engines Use API Certified SAE 5W -20 Engine Oil, meeting the requir ements of Chrysler Material [...]

Chassis Component Fluid, Lubricant, or Genuine Part Automatic T ransmission MOP AR 威 A TF+4 威 Automatic T ransmission Fluid or equivalent licensed A TF+4 威 product. T ransfer Case – NV140 Single Speed Only MOP AR 威 A TF+4 威 Automatic T ransmission Fluid or equivalent licensed A TF+4 威 product. T ransfer Case – NV245 T wo Speed Only [...]

I n f o r m a t i o n P r o v i d e d b y :[...]

MAINTENANCE SCHEDULES CONTENTS 䡵 Emissions Control System Maintenance ...... 4 1 8 䡵 Maintenance Schedule .................. 4 1 8 ▫ Required Maintenance Intervals .......... 4 2 0 8 M A I N T E N A N C E S C H E D U L E S I n f o r m a t i o n P r o v i d e d b y :[...]

EMISSIONS CONTROL SYSTEM MAINTENANCE The Scheduled Maintenance services listed in bold type must be done at the times or mileages specified to ensure the continued pr oper functioning of the emissions control system. These and all other maintenance services in- cluded in this manual, should be done to provide best vehicle performance and reliabilit[...]

• Change your engine oil more often if you drive your vehicle off-r oad for an extended period of time. • Under no circumstances should oil change intervals exceed 6,000 miles (10,000 km) or 6 months, whichever comes first. Y our authorized dealer will reset the oil change indicator message after completing the scheduled oil change. If a schedu[...]

At Each Oil Change • Change the engine oil filter . • Inspect the brake hoses and lines. CAUTION! Failure to perform the required maintenance items may result in damage to the vehicle. Required Maintenance Intervals Refer to the Maintenance Schedules on the following pages for the requir ed maintenance intervals. 8 M A I N T E N A N C E S C H E[...]

6,000 Miles (10,000 km) or 6 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. Odometer Reading Date Repair Order # Dealer Code Signature Authorized Chrysler Dealer 12,000 Miles (20,000 km) or 12 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tir[...]

18,000 Miles (30,000 km) or 18 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ Inspect the front and rear axle fluid, change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing. Odometer Reading Date Repair Order # Dealer Code Signature Authorized Chrysler De[...]

30,000 Miles (50,000 km) or 30 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ Replace the engine air cleaner filter . ❏ Replace the spark plugs (3.7L and 5.7L Engines). ❏ Adjust parking brake on vehicles equipped with four-wheel disc brakes. ❏ Inspect the transfer case fluid. Odomet[...]

42,000 Miles (70,000 km) or 42 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. Odometer Reading Date Repair Order # Dealer Code Signature Authorized Chrysler Dealer 48,000 Miles (80,000 km) or 48 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate t[...]

54,000 Miles (90,000 km) or 54 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ Inspect the front and rear axle fluid, change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing. Odometer Reading Date Repair Order # Dealer Code Signature Authorized Chrysler De[...]

66,000 Miles (1 10,000 km) or 66 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. Odometer Reading Date Repair Order # Dealer Code Signature Authorized Chrysler Dealer 72,000 Miles (120,000 km) or 72 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotat[...]

78,000 Miles (130,000 km) or 78 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. Odometer Reading Date Repair Order # Dealer Code Signature Authorized Chrysler Dealer 84,000 Miles (140,000 km) or 84 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate[...]

90,000 Miles (150,000 km) or 90 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ Replace the engine air cleaner filter . ❏ Replace the spark plugs (3.7L and 5.7L Engines). ❏ Inspect and replace PCV valve if necessary. † ❏ Adjust parking brake on vehicles equipped with four-wheel dis[...]

96,000 Miles (160,000 km) or 96 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary . ❏ Inspect the brake linings; replace if necessary . ❏ Inspect the [...]

108,000 Miles (180,000 km) or 108 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary . ❏ Inspect the brake linings; replace if necessary . ❏ Inspect th[...]

120,000 Miles (200,000 km) or 120 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ Replace the engine air cleaner filter . ❏ Replace the ignition cables (3.7L Engine). ❏ Replace the spark plugs (3.7L and 5.7L Engines). ❏ Adjust parking brake on vehicles equipped with four-wheel disc b[...]

132,000 Miles (220,000 km) or 132 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary . ❏ Inspect the brake linings; replace if necessary . ❏ Inspect th[...]

144,000 Miles (240,000 km) or 144 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary . ❏ Inspect the brake linings; replace if necessary . ❏ Inspect th[...]

† This maintenance is recommended by the manufacturer to the owner , but is not requir ed to maintain emissions warranty . W ARNING! • Y ou can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, t[...]

IF YOU NEED CONSUMER ASSIST ANCE CONTENTS 䡵 Suggestions For Obtaining Service For Y our V ehicle .............................. 4 3 7 ▫ Prepar e For The Appointment ........... 4 3 7 ▫ Prepar e A List ...................... 4 3 7 ▫ Be Reasonable W ith Requests ............ 4 3 7 䡵 If Y ou Need Assistance ................. 4 3 7 ▫ Chrysl[...]

䡵 Publication Order Forms ................ 4 4 1 䡵 Department Of T ransportation Uniform T ire Quality Grades ........................ 4 4 3 ▫ T readwear ......................... 4 4 3 ▫ T raction Grades ..................... 4 4 3 ▫ T emperature Grades .................. 4 4 4 436 IF YOU NEED CONSUMER ASSIST ANCE I n f o r m a t i o n P[...]

SUGGESTIONS FOR OBT AINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sur e to have the right papers with you. T ake your warranty folder . All work to be performed may not be covered by the warranty . Discuss additional charges with the service manager . Keep a maintenance log of your vehicle’s[...]

This is why you should always talk to an authorized dealer’s service manager first. Most matters can be re- solved with this process. • If for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealer- ship. They want to know if you need assistance. • If an authorized dealership is unable to resolv[...]

Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) T o assist customers who have hearing difficulties, the manufacturer has installed special TDD (T elecommuni- cation Devices for the Deaf) equipment at its customer center . Any hearing or speech impaired customer , who has access to a TDD or a conventional teletypewriter (TTY) in the[...]

W e appreciate that you have made a major investment when you purchased the vehicle. An authorized dealer has also made a major investment in facilities, tools, and training to assure that you are absolutely delighted with the ownership experience. Y ou’ll be pleased with their sincere efforts to resolve any warranty issues or related concerns. W[...]

If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However , NHTSA cannot become involved in individual problems between you, your authorized dealer , and the manufacturer . T o contact NHTSA, you may either call the Auto [...]

• Service Manuals These comprehensive Service Manuals provide the infor- mation that students and professional technicians need in diagnosing/troubleshooting, problem solving, main- taining, servicing, and repairing Chrysler Group LLC vehicles. A complete working knowledge of the vehicle, system, and/or components is written in straightforwar d l[...]

DEP ARTMENT OF TRANSPORT A TION UNIFORM TIRE QUALITY GRADES The following tir e grading categories were established by the National Highway T raffic Safety Administration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your vehicle. All passenger car tires must conform to Fe[...]

T emperature Grades The temperature grades are A (the highest), B, and C, repr esenting the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire [...]

INDEX 10 I n f o r m a t i o n P r o v i d e d b y :[...]

ABS (Anti-Lock Brake System) .............. 2 6 8 Adding Fuel ........................... 3 2 0 Adjustable Pedals ........................ 1 1 5 Air Cleaner , Engine (Engine Air Cleaner Filter) . . . 372 Air Conditioner Maintenance ............... 3 7 4 Air Conditioning ........................ 2 2 4 Air Conditioning, Operating T ips ............ 2[...]

Special Additives ...................... 3 8 9 T or que Converter ...................... 2 5 1 Autostick ............................. 2 4 6 Auxiliary Electrical Outlet (Power Outlet) ...... 1 3 7 Auxiliary Power Outlet ................... 1 3 7 Battery ............................... 3 7 3 Keyless T ransmitter Replacement (RKE) ....... 2 4 Saving [...]

Light ............................... 1 4 3 Luggage Carrier ....................... 1 5 0 Cargo Light ............................ 1 4 3 Cargo Load Floor ........................ 1 4 7 Cargo T ie-Downs ........................ 1 4 5 Cargo (V ehicle Loading) ................... 3 2 2 Cellular Phone ........................ 84,221 Center High Mounted[...]

Disposal of Used Coolant ................ 3 8 4 Drain, Flush, and Refill .................. 3 8 1 Inspection ........................... 3 8 0 Points to Remember .................... 3 8 4 Pressur e Cap ......................... 3 8 3 Radiator Cap ......................... 3 8 3 Selection of Coolant (Antifreeze) ......... 381,413 Cruise Light .....[...]

Brake Assist System .................... 2 7 1 Electronic Roll Mitigation ................ 2 7 2 Electronic Stability Program ............... 2 7 3 T raction Control System ................. 2 7 1 Electronic Roll Mitigation (ERM) ............. 2 7 2 Electronic Speed Control (Cruise Control) ....... 1 1 6 Electronic Stability Program (ESP) .........[...]

Starting ............................. 2 4 0 T emperatur e Gauge .................... 1 6 3 Engine Oil V iscosity ...................... 3 7 1 Engine Oil V iscosity Chart ................. 3 7 1 Enhanced Accident Response Feature .......... 5 5 Entry System, Illuminated .................. 2 0 Exhaust Gas Caution ................ 72,319,378 Exhaust [...]

Front Axle (Differ ential) ................... 3 8 7 Front Heated Seats ....................... 8 9 Fuel ................................. 3 1 5 Conserving .......................... 1 7 4 Filler Cap (Gas Cap) .................... 3 2 0 Gasoline ............................ 3 1 5 Gauge .............................. 1 6 7 Materials Added ..........[...]

Head Rests ............................. 8 8 Headlights .......................... 102,407 Bulb Replacement ...................... 4 0 8 Cleaning ............................ 3 9 7 On W ith W ipers ....................... 1 0 3 Replacing ........................... 4 0 8 Heated Mirrors .......................... 8 3 Heated Seats ...................[...]

Inverter , Power ......................... 1 4 0 Jack Location ........................... 3 4 8 Jack Operation ....................... 348,351 Jacking Instructions ...................... 3 5 1 Jump Starting .......................... 3 5 5 Key , Programming ........................ 1 8 Key , Replacement ........................ 1 8 Key , Sentry (I[...]

Cruise .............................. 1 6 6 Daytime Running ...................... 1 0 4 Dimmer Switch, Headlight ............. 101,108 Electronic Stability Program (ESP) Indicator . . . 283 Electronic Throttle Control W arning ......... 1 6 7 Exterior .............................. 7 4 F o g .......................... 106,167,410 Four-Wheel Drive [...]

Load Floor , Cargo ....................... 1 4 7 Loading V ehicle ......................... 3 2 2 T i r e s ............................... 2 9 1 Locks ................................. 2 8 Automatic Door ........................ 2 9 Child Protection ........................ 2 9 Door ................................ 2 8 Power Door .................[...]

Multi-Function Control Lever ............... 1 0 1 New V ehicle Break-In Period ................ 7 1 Occupant Restraints ................... 35,52,56 Occupant Restraints (Sedan) ............. 49,52,54 Octane Rating, Gasoline (Fuel) .............. 3 1 5 Odometer .......................... 164,166 T r i p ................................ 1 6 4 Off-Pa[...]

Park Sense System, Rear ................... 1 1 9 Parking Brake .......................... 2 6 5 Passing Light ........................... 1 0 8 Pedals, Adjustable ....................... 1 1 5 Personal Settings ........................ 1 7 8 Pets .................................. 7 1 Pets, T ransporting ........................ 7 1 Phone, Cellula[...]

Rear Heated Seats ........................ 9 1 Rear Park Sense System ................... 1 1 9 Rear Seat, Folding ........................ 9 3 Rear W indow Defroster ................... 1 4 9 Rear W indow Features .................... 1 4 8 Rear W iper/W asher ...................... 1 4 8 Rearview Mirrors ........................ 8 0 Reclining Fro[...]

Safety T ips ............................. 7 2 Satellite Radio Antenna ................... 2 1 5 Satellite Radio (uconnect 威 studios) ........... 2 1 4 Schedule, Maintenance .................... 4 1 8 Seat Belt Reminder ....................... 4 3 Seat Belts ............................ 36,73 Adjustable Upper Shoulder Anchorage ........ 4 1 And P[...]

Setting the Clock ................ 184,185,189,198 Settings, Personal ........................ 1 7 8 Shift Lock Manual Override ................ 2 4 4 Shifting ............................... 2 4 3 Automatic T ransmission ................. 2 4 3 Shoulder Belts ........................... 3 6 Signals, T urn ................. 74,107,159,409,410 Smart[...]

Sway Control, T railer ..................... 2 7 8 Synthetic Engine Oil ...................... 3 7 1 System, Remote Starting .................... 2 5 T achometer ............................ 1 6 1 T elescoping Steering Column ............... 1 1 4 T emperatur e Control, Automatic (A TC) ........ 2 2 4 T emperatur e Gauge, Engine Coolant .......... [...]

Spinning ............................ 2 9 9 T r ead W ear Indicators ................... 3 0 0 Wheel Mounting ...................... 3 5 4 T ongue W eight/T railer W eight .............. 3 3 1 T or que Converter Clutch .................. 2 5 1 T ow Hooks, Emergency ................... 3 5 9 T ow/Haul Indicator Light ................. 1 6 5 T owing [...]

uconnect™ (Hands-Free Phone) .............. 8 4 Underhood Fuses ..................... 401,404 Uniform T ire Quality Grades ................ 4 4 3 Universal Consumer Interface (UCI) Connector . . . 209 Universal T ransmitter ..................... 1 2 8 Upholstery Care ........................ 3 9 6 V anity Mirrors ........................... 8 4 V[...]

Chrysler Group LL C 10 WK741 -126-AB 2nd Edition Printed in U.S.A. I n f o r m a t i o n P r o v i d e d b y :[...]