Lincoln 2008 Town Car manuel d'utilisation

Introduction 4 Instrument Cluster 10 W arning lights and chimes 10 Gauges 14 Entertainment Systems 17 AM/FM stereo with in-dash six CD 17 Climate Controls 24 Dual automatic temperature control 24 Rear window defroster 27 Lights 28 Headlamps 28 T urn signal control 32 Bulb replacement 32 Driver Controls 39 W indshield wiper/washer control 39 Steerin[...]

Tires, Wheels and Loading 134 T ire information 134 T ire Pressure Monitoring System (TPMS) 149 V ehicle loading 155 T railer towing 160 Recreational towing 163 Driving 164 Starting 164 Brakes 169 T raction Control™ 172 Air suspension 174 T ransmission operation 174 Roadside Emergencies 182 Getting roadside assistance 182 Hazard flasher switch 18[...]

Maintenance and Specifications 221 Engine compartment 223 Engine oil 225 Battery 228 Engine coolant 230 Fuel information 236 Air filter(s) 252 Maintenance product specifications and capacities 255 Engine data 258 Accessories 261 Index 263 All rights reserved. Reproduction by any means, electronic or mechanical including photocopying, recording or b[...]

CALIFORNIA Proposition 65 W arning W ARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain or emit chemic[...]

SAFETY AND ENVIRONMENT PROTECTION W arning symbols in this guide How can you reduce the risk of personal injury to yourself or others? In this guide, answers to such questions are contained in comments highlighted by the warning triangle symbol. These comments should be read and observed. W arning symbols on your vehicle When you see this symbol, i[...]

Special instructions For your added safety , your vehicle is fitted with sophisticated electronic controls. Please read the section Airbag supplemental restraint system (SRS) in the Seating and Safety Restraints chapter . Failure to follow the specific warnings and instructions could result in personal injury . Front seat mounted rear -facing child[...]

other government authorities or other third parties acting with lawful authority . Other parties may seek to access the information independently of Ford Motor Company and Ford of Canada. Cell phone use The use of Mobile Communications Equipment has become increasingly important in the conduct of business and personal affairs. However , drivers mus[...]

These are some of the symbols you may see on your vehicle. V ehicle Symbol Glossary Safety Alert See Owner’ s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat Lower Anchor Child Seat T ether Anchor Brake System Anti-Lock Brake System Parking Brake System Brake Fluid - Non-Petroleum Based Parking Aid System Stability Control System[...]

V ehicle Symbol Glossary Power W indows Front/Rear Power W indow Lockout Child Safety Door Lock/Unlock Interior Luggage Compartment Release Panic Alarm Engine Oil Engine Coolant Engine Coolant T emperature Do Not Open When Hot Battery A void Smoking, Flames, or Sparks Battery Acid Explosive Gas Fan W arning Power Steering Fluid Maintain Correct Flu[...]

W ARNING LIGHTS AND CHIMES W arning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’ s functions. Many lights will illuminate when you start your vehicle to make sure the bulb works. If any light remains [...]

Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter , the fuel system, interior floor coverings or other vehicle components, possibly causing a fire. Brake system warning light: To confirm the brake system warning light is functional, it will momentarily illuminate when the ignition is turned to the [...]

Safety belt: Reminds you to fasten your safety belt. A Belt-Minder 威 chime will also sound to remind you to fasten your safety belt. Refer to the Seating and Safety Restraints chapter to activate/deactivate the Belt-Minder 威 chime feature. Charging system: Illuminates when the battery is not charging properly . Engine oil pressure: Illuminates [...]

O/D off: Illuminates when the overdrive function of the transmission has been turned off, refer to the Driving chapter . If the light does not illuminate, have the transmission serviced soon, or damage may occur . Speed control: Illuminates when the speed control is activated. T urns off when the speed control system is deactivated. T urn signal: I[...]

GAUGES Speedometer: Indicates the current vehicle speed. Refer to the Message center in the Driver Controls chapter to change your display to a digital speedometer . The digital display is more accurate than the analog gauge and may not match. Engine coolant temperature gauge: Indicates engine coolant temperature. At normal operating temperature, t[...]

Odometer: Registers the total miles (kilometers) of the vehicle. Refer to Message center in the Driver Controls chapter on how to switch the display from Metric to English and the odometer to the speedometer . T rip odometer: Registers the miles (kilometers) of individual journeys. Press and release the message center INFO button until “TRIP” a[...]

Fuel gauge: Indicates approximately how much fuel is left in the fuel tank (when the ignition is in the ON position). The fuel gauge may vary slightly when the vehicle is in motion or on a grade. The arrow near the fuel pump icon indicates which side of the vehicle the fuel filler door is located. Refer to Filling the tank in the Maintenance and Sp[...]

AUDIO SYSTEMS Audiophile Satellite Compatible AM/FM Stereo In-dash Six CD sound system Driving while distracted can result in loss of vehicle control, accident and injury . Ford strongly recommends that drivers use extreme caution when using any device that may take their focus off the road. The drivers primary responsibility is the safe operation [...]

2. SEEK: Press to access the next/previous radio station or CD track. Press and hold to advance/reverse in the current CD track. 3. TUNE/CA T : Press to manually go up or down the radio frequency . CA T is only available when equipped with Satellite radio. Y our vehicle may be equipped with Satellite ready capability . The kit to enable Satellite r[...]

F ADE: Press F ADE; then press SEL-TEXT to shift sound to the rear/front speakers. 8. SEL-TEXT : Use with Bass, T reble, Balance, Fade and other menu functions. TEXT : TEXT is only available when equipped with Satellite radio. Y our vehicle may be equipped with Satellite ready capability . The kit to enable Satellite reception is available through [...]

Press SEL-TEXT again to disable the feature when COMPRESS ON is displayed. When activated, the compression icon will illuminate in the display . Occupancy mode: (A vailable on Audiophile audios only): Press MENU until occupancy mode appears in the display . Press SEL-TEXT to select ALL, DRIVER or REAR SEA T occupancy mode. Autoset: Allows you to se[...]

12. LOAD: Press to load a CD. Press LOAD and a specific preset to load in that particular slot. A vailable slots are indicated by small flashing indicators in the display . When the system is ready to accept a disc, LOAD CD X will appear in the display . Load the CD. Press and hold to autoload up to six discs. Note: Ensure that the system is ready [...]

GENERAL AUDIO INFORMATION Radio frequencies: AM and FM frequencies are established by the Federal Communications Commission (FCC) and the Canadian Radio and T elecommunications Commission (CRTC). Those frequencies are: AM: 530, 540–1700, 1710 kHz FM: 87.7, 87.9–107.7, 107.9 MHz Radio reception factors: There are three factors that can affect ra[...]

CD units are designed to play commercially pressed 4.75 in (12 cm) audio compact discs only . Due to technical incompatibility , certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players. Dirty , warped or damaged CDs, irregular shaped CDs, CDs with a scratch protection film attached, and CDs with ho[...]

DUAL ELECTRONIC AUTOMATIC TEMPERATURE CONTROL (DEA TC) SYSTEM 1. A/C control: Cools the vehicle and is used to reduce humidity in the vehicle. Press to turn on/off. The A/C control engages automatically in Auto, Defrost and Floor/Defrost modes. 2. Recirculation control: Cools the vehicle more quickly by recirculating the cabin air instead of using [...]

5. DUAL (Single/dual temperature control): Allows the driver to have full control of the cabin temperature settings (single zone) or allows the passenger to have control of their individual temperature settings (dual zone). Press to turn on dual zone mode, press again to return to single zone. 6. : Distributes air through the windshield defroster v[...]

15. EXT : Displays the outside air temperature. It will remain displayed until the EXT control is pressed again. The external temperature will be most accurate when the vehicle has been moving for a period of time. 16. T emperature conversion: Press to toggle between Fahrenheit and Celsius temperature on the DEA TC display only . The set point temp[...]

REAR CONSOLE CLIMATE CONTROLS (IF EQUIPPED) • TEMP: Press to increase or decrease airflow temperature. • F AN: Press to increase or decrease the fan speed. REAR WINDOW DEFROSTER The rear defroster control is located on the instrument panel. Press the rear defroster control to clear the rear window of thin ice and fog. A small LED will illuminat[...]

HEADLAMP CONTROL T urns the lamps off. T urns on the parking lamps, instrument panel lamps, license plate lamps and tail lamps. T urns the headlamps on. Autolamp control The autolamp system provides light sensitive automatic on-off control of the exterior lights normally controlled by the headlamp control. The autolamp system also keeps the lights [...]

6. W ait the desired amount of time for delay , then turn the headlamp switch to off. • At this point, the exterior lamps turn off and the time delay is set. Fog lamp control (if equipped) The fog lamps can be turned on when the headlamp control is pulled toward you and is in any of the following positions: • Parking lamps • Low beams • Aut[...]

• the headlamp system is not turned on by another feature such as using the headlamp control or Autolamp. Always remember to turn on your headlamps at dusk or during inclement weather . The Daytime Running Light (DRL) System does not activate the tail lamps and generally may not provide adequate lighting during these conditions. Failure to activa[...]

• (1) 8 feet (2.4 meters) • (2) Center height of lamp to ground • (3) 25 feet (7.6 meters) • (4) Horizontal reference line 2. Measure the height of the headlamp bulb center from the ground and mark an 8 foot (2.4 meter) horizontal reference line on the vertical wall or screen at this height (a piece of masking tape works well). 3. T urn on [...]

TURN SIGNAL CONTROL • Push down to activate the left turn signal. • Push up to activate the right turn signal. INTERIOR LAMPS Map/Courtesy lamps T o turn on the map lamps, press the map lamp control. Rear courtesy/reading lamps The courtesy lamp lights when: • any door is opened. • any of the remote entry controls are pressed and the igniti[...]

Using the right bulbs Replacement bulbs are specified in the following chart. Headlamp bulbs must be marked with an authorized “D.O.T .” for North America and an “E” for Europe to ensure lamp performance, light brightness and pattern and safe visibility . The correct bulbs will not damage the lamp assembly or void the lamp assembly warranty[...]

Rear courtesy/reading lamps T o replace the rear courtesy/reading lamp bulbs in the rear assist handle: 1. Make sure the headlamp control is in the off position. 2. Under the handle, remove two trim screw covers, retaining screws, lamp assembly and assist handle from the headliner . 3. Disconnect the electrical connector from the lamp assembly . 4.[...]

Low beam • Disconnect electrical connector and remove retainer and headlamp bulb from headlamp assembly . High beam • Remove the bulb by turning it counterclockwise and then pulling it straight out. • Disconnect the electrical connector from the bulb. Handle a halogen headlamp bulb carefully and keep out of children’ s reach. Grasp the bulb[...]

Replacing front parking lamp/turn signal/sidemarker bulbs The front parking lamp/turn signal/sidemarker bulbs are located in the headlamp assembly . Follow the same steps to replace either bulb. 1. Make sure the headlamp switch is in the off position, then open the hood. 2. Remove five retainers and radiator cover . 3. Remove three bolts, pull head[...]

4. Remove the bulb socket by rotating it counterclockwise, then pulling it out of the lamp assembly . 5. Pull the bulb from the socket and push in the new bulb. 6. T o complete installation, follow the removal procedure in reverse order . Replacing license plate lamp bulbs 1. Make sure the headlamp switch is in the off position, then remove two scr[...]

Replacing high-mount brakelamp assembly T o change the high-mount brakelamp assembly: 1. Remove the high-mount brakelamp assembly from the headliner by pulling downward on the assembly . 2. Disconnect the electrical connector and remove the high-mount brakelamp assembly . 3. Install the new high-mount brakelamp assembly by aligning the tabs and pus[...]

MULTI-FUNCTION LEVER W indshield wiper: Rotate the end of the control away from you to increase the speed of the wipers; rotate towards you to decrease the speed of the wipers. W indshield washer: Push the end of the stalk: • briefly: causes a single swipe of the wipers without washer fluid. • a quick push and hold: the wipers will swipe three [...]

TILT STEERING WHEEL T o adjust the steering wheel: 1. Pull and hold the steering wheel release control toward you. 2. Move the steering wheel up or down until you find the desired location. 3. Release the steering wheel release control. This will lock the steering wheel in position. Never adjust the steering wheel when the vehicle is moving. ILLUMI[...]

CLOCK Press the right control to move the time display forward. Press the left control to move the time display backwards. AUXILIARY POWER POINT (12VDC) Power outlets are designed for accessory plugs only . Do not insert any other object in the power outlet as this will damage the outlet and blow the fuse. Do not hang any type of accessory or acces[...]

• do not leave battery chargers, video game adapters, computers and other devices plugged in overnight or when the vehicle is parked for extended periods. Always keep the power point caps closed when not being used. Cigar/Cigarette lighter (if equipped) Do not plug optional electrical accessories into the cigarette lighter socket. Do not hold the[...]

Remote seat adjustment lockout The window lockout control, located on the drivers door , will also lockout the remote seat adjustment. T o lock out the remote seat adjustment feature, press the right side of the control. Press the left side to restore the remote seat adjustment control. Rear console radio/climate controls (if equipped) Refer to the[...]

One touch down • Press AUTO completely down and release quickly . The driver’ s window will open fully . Depress again to stop window operation. One touch down can be deactivated during operation by pushing down on the top part of the driver power window control. Window lock The window lock feature allows only the driver to operate the power wi[...]

AUTOMATIC DIMMING INTERIOR REAR VIEW MIRROR (IF EQUIPPED) Y our vehicle may be equipped with an interior rear view mirror which has an auto-dimming function (optional on the driver’ s side exterior mirror). The electronic day/night mirror will change from the normal (high reflective) state to the non-glare (darkened) state when bright lights (gla[...]

Heated outside mirrors (if equipped) Both mirrors are heated automatically to remove ice, mist and fog when the rear window defrost is activated. Do not remove ice from the mirrors with a scraper or attempt to readjust the mirror glass if it is frozen in place. These actions could cause damage to the glass and mirrors. Fold-away mirrors (if equippe[...]

Do not use the speed control in heavy traffic or on roads that are winding, slippery or unpaved. Setting speed control The controls for using your speed control are located on the steering wheel for your convenience. 1. Press the ON control and release it. 2. Accelerate to the desired speed. 3. Press the SET + control and release it. 4. T ake your [...]

Resuming a set speed Press the RESUME control and release it. This will automatically return the vehicle to the previously set speed. Increasing speed while using speed control There are two ways to set a higher speed: • Press and hold the SET + control until you get to the desired speed, then release the control. Y ou can also use the SET + cont[...]

• Depress the brake pedal until the desired vehicle speed is reached, press the SET + control. Turning of f speed control There are two ways to turn off the speed control: • Depress the brake pedal. This will not erase your vehicle’ s previously set speed. • Press the speed control OFF control. Note: When you turn the speed control or the i[...]

Audio control features In Radio mode: • Press NEXT to select the next preset station within the current radio band. In T ape mode: • Press NEXT to listen to the next selection on the tape. In CD mode: • Press NEXT to listen to the next track on the disc. In any mode: • Press VOL + or - to adjust the volume. Climate control features (if equi[...]

HOMELINK 姞 WIRELESS CONTROL SYSTEM (IF EQUIPPED) The HomeLink 威 W ireless Control System, located on the driver’ s visor , provides a convenient way to replace up to three hand-held transmitters with a single built-in device. This feature will learn the radio frequency codes of most transmitters to operate garage doors, entry gate operators, [...]

1. Position the end of your hand-held transmitter 1–3 inches (2–8 cm) away from the HomeLink 威 button you wish to program (located on your overhead console) while keeping the indicator light in view . 2. Simultaneously press and hold both the chosen HomeLink 威 and hand-held transmitter buttons until the HomeLink 威 indicator light changes [...]

Gate Operator & Canadian Programming During programming, your hand-held transmitter may automatically stop transmitting — not allowing enough time for HomeLink 威 to accept the signal from the hand-held transmitter . After completing Step 1 outlined in the Programming section, replace Step 2 with the following: Note: If programming a garage [...]

Erasing HomeLink 姞 buttons T o erase the three programmed buttons (individual buttons cannot be erased): • Press and hold the two outer HomeLink 威 buttons until the indicator light begins to flash-after 20 seconds. Release both buttons. Do not hold for longer that 30 seconds. HomeLink 威 is now in the train (or learning) mode and can be prog[...]

Y our display can show up to 3 reconfigurable telltales at one time. What ever is displayed in the top left corner has the highest priority . Premium Display Severity Indicator (located under the message center): Indicates severity of the information being displayed on the premium display . Red for high severity , amber for medium severity , and no[...]

Info menu This control displays the following control displays: • Odometer/T rip odometer (T rip A and T rip B) • Hour meter (if equipped) • Distance to Empty • A verage Fuel Economy • Instantaneous Fuel Economy • T rip elapsed drive time Odometer/Trip odometer Refer to Gauges in the Instrument Cluster chapter . Hour meter (if equipped)[...]

Average fuel economy (AFE) Select this function from the INFO menu to display your average fuel economy in miles/gallon or liters/100 km. If you calculate your average fuel economy by dividing gallons of fuel used by 100 miles traveled (kilometers traveled by liters used), your figure may be different than displayed for the following reasons: • Y[...]

Trip elapsed drive time Select this function from the INFO menu to display a timer . T o operate the T rip Elapsed Drive T ime perform the following: 1. Press and release RESET in order to start the timer . 2. Press and release RESET to pause the timer . 3. Press and hold RESET for 2 seconds in order to reset the timer to zero. Setup menu Press thi[...]

System check Selecting this function from the SETUP menu causes the message center to cycle through each of the systems being monitored. For each of the monitored systems, the message center will indicate either an OK message or a warning message for three seconds. Pressing the SELECT control cycles the message center through each of the systems be[...]

T ext Size 1. Select this function from the SETUP menu. 2. Press the SELECT control to change text size. Units (English/Metric) 1. Select this function from the SETUP menu for the current units to be displayed. 2. Press the SELECT control to change from English to Metric. Language 1. Select this function from the SETUP menu for the current language[...]

Most geographic areas (zones) have a magnetic north compass point that varies slightly from the northerly direction on maps. This variation is four degrees between adjacent zones and will become noticeable as the vehicle crosses multiple zones. A correct zone setting will eliminate this error . Refer to Compass zone/calibration adjustment. Compass [...]

9. Slowly drive the vehicle in a circle (less than 3 mph [5 km/h]) until the CIRCLE SLOWL Y TO CALIBRA TE COMP ASS display changes to COMP ASS CALIBRA TION COMPLETED. It will take up to five circles to complete calibration. 10. The compass is now calibrated. Oil Minder Start V alue 1. Select this function from the SETUP control for the current disp[...]

Reverse Sensing System (Park Aid) This feature sounds a warning tone to warn the driver of obstacles near the rear bumper , and functions only when R (Reverse) gear is selected. 1. Before you disable/enable the reverse sensing system feature, put the vehicle in R (Reverse). 2. Press the RESET control to turn the park aid ON or OFF . System warnings[...]

W arning display Status Park aid ON/OFF W arning returns after the ignition key is turned from off to ON. Overdrive ON/OFF T runk ajar Low tire pressure T ire pressure monitor fault T ire pressure sensor fault Check compass module Low washer fluid Change engine oil DOOR AJAR. Displayed when a door is not completely closed. POWER TRAIN MALFUNCTION D[...]

TRUNK AJAR. Displayed when the trunk is not completely closed. OVERDRIVE ON/OFF . Displayed when the overdrive is enabled or disabled. LOW TIRE PRESSURE. Displayed when one or more tires on your vehicle have low tire pressure. Refer to Inflating your tires in the T ires, Wheels and Loading chapter . TIRE PRESSURE MONITOR F AUL T . Displayed when th[...]

T o reset the oil monitoring system to 100% after each oil change [approximately 7,500 miles (12,000 km) or 6 months] perform the following: 1. Press and hold the RESET control for 2 seconds and release. Oil life is set to 100% and “OIL LIFE XXX% HOLD RESET IF NEW OIL” is displayed. 2. Press and hold the RESET control for 3 seconds and release.[...]

POWER T RUNK (IF EQUIPPED) Y our vehicle may be equipped with a power trunk controlled by the interior trunk control, the key fob or the keypad on the door . If anything obstructs the power trunk while it is closing, the trunk will automatically reverse to the open position, provided it meets sufficient resistance. Resistance must be as strong as t[...]

FUEL DOOR RELEASE Y our vehicle is equipped with a locking fuel door . T o open the door , press the control located on the door . Fuel filler door override release If the remote release is inoperative, open the trunk, then pull the override release handle located inside the trunk to open the fuel filler door . 2008 T own Car (tow) Owners Guide (po[...]

KEYS Y our vehicle is equipped with a master key and a valet (identified with the word V ALET) key lock system. • The master key will access the vehicle’ s doors, trunk, glove box, ignition and remote trunk release. • The valet key will access doors and ignition only . Before using the valet key with an attendant, lock the interior trunk cont[...]

• If the key is turned a second time to the unlock position within 5 seconds, all vehicle doors will unlock. Autolock This feature automatically locks all vehicle doors when the following conditions are met: • all the doors are closed, • the engine is running, • you shift into gear , putting the vehicle in motion, and. • the vehicle’ s [...]

2. Press the power door unlock control on the door panel three times. 3. T urn the ignition from the 3 (ON) to the 1 (OFF/LOCK) position. 4. Press the power door unlock control three times. 5. T urn the ignition back to the 3 (ON) position. 6. The door locks will lock/unlock to confirm programming mode is entered/active. 7. W ith the ignition still[...]

T o open the luggage compartment door (lid) from within the luggage compartment, pull the illuminated “T” shaped handle and push up on the trunk lid. The handle is composed of a material that will glow for hours in darkness following brief exposure to ambient light. The “T” shaped handle will be located either on the luggage compartment doo[...]

REMOTE ENTRY SYSTEM This device complies with part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Radio type approva[...]

Unlocking the doors 1. Press and release to unlock the driver’ s door . Note: The interior lamps will illuminate. 2. Press and release again within five seconds to unlock all the doors. Security lighting Y our vehicle’ s headlamps and park lamps will illuminate if: • it is dark outside (evening), • the headlamp control is in the autolamp po[...]

Before operating the power decklid, be sure that no one, particularly a child, is in a position where he or she can be injured by the trunk lid. NEVER leave the remote entry transmitter where it can be inadvertently activated, as someone could be seriously injured by a moving decklid. • Ensure that the trunk is closed and latched before driving y[...]

3. W ithin five seconds, press one control on the remote transmitter and then press the 1 or 2 button on the driver’ s door panel to which you would like to associate with the memory positions and Driver 1 or Driver 2 positions. 4. Repeat this procedure for another remote transmitter , if desired. Deactivating the memory seat/mirrors/adjustable p[...]

2. Do not wipe off any grease on the battery terminals on the back surface of the circuit board. 3. Remove the old battery . Note: Please refer to local regulations when disposing of transmitter batteries. 4. Insert the new battery . Refer to the diagram inside the remote entry transmitter for the correct orientation of the battery . Press the batt[...]

Note: Ensure the brake pedal is not depressed during this sequence. T o reprogram the remote entry transmitters: 1. Ensure the vehicle is electronically unlocked. 2. Put the key in the ignition. 3. Cycle eight times rapidly (within 10 seconds) between the 1 (OFF/LOCK) position and the 3 (ON) position. Note: The eighth turn must end in the 3 (ON) po[...]

The inside lights will not turn off if: • they have been turned on with the dimmer control, or • any door is open. The battery saver will shut off the interior lamps 30 minutes after the last door is closed, or after 10 minutes if the last door is left open. KEYLESS ENTRY SYSTEM (IF EQUIPPED) Y ou can use the keyless entry keypad to: • lock o[...]

T ips for setting codes: • Do not set a code that uses five of the same number . • Do not use five numbers in sequential order . Erasing personal codes 1. Enter the factory set 5–digit code. The keyless entry keypad and interior lights will illuminate and the driver’ s door will unlock. 2. Press and release the 1 • 2 within five seconds o[...]

Anti-scan feature If the wrong code has been entered 7 times (35 consecutive button presses), the keypad will go into an anti-scan mode. This mode disables the keypad for one minute and the keypad lamp will flash. The anti-scan feature will turn off after: • one minute of keypad inactivity . • pressing the control on the remote entry transmitte[...]

Immobiliser System P A TS XCVR certification numbers Kuwait M.C/U.S.0 /5/7-12579 Mauritius T A/2005/15 Mayotte (F) Mexico RL VVIVP03-324 Morocco MR 1299 ANRT 2004 Netherlands Antilles (NL) Nicaragua NCG-CE-04-004 Northern Mariana Islands See USA Oman OMA/1265(A) 1308/2001 Puerto Rico See USA Qatar QTEL/SR/2003/R-276 Saudi Arabia (10/1900) South Kor[...]

engine. If a problem occurs, turn the ignition off, remove all objects on the key chain away from the coded key and restart the engine. Anti-theft indicator The anti-theft indicator is located on top of the instrument panel. • When the ignition is in the 1 (OFF/LOCK) position, the indicator will flash once every 2 seconds to indicate the SecuriLo[...]

Replacing coded keys can be very costly . Store an extra programmed key away from the vehicle in a safe place to help prevent any inconveniences. Please visit an authorized dealer to purchase additional spare or replacement keys. Programming spare keys Y ou can program your own coded keys to your vehicle. Please read and understand the entire proce[...]

9. Y our new unprogrammed key is now programmed. If the key has been successfully programmed it will start the vehicle’ s engine and the theft indicator light will illuminate for three seconds and then go out. If the key was not successfully programmed, it will not start your vehicle’ s engine and the theft indicator light will flash on and off[...]

Disarming the system Y ou can disarm the system by any of the following actions: • Unlock the doors by using the remote entry transmitter . • Unlock the doors using a valid code on the keypad. • Unlock the doors with the key in the key lock cylinder . • T urn the ignition to the 3 (ON) position. 2008 T own Car (tow) Owners Guide (post-2002-[...]

SEA TING Adjustable head restraints T o minimize the risk of neck injury in the event of a crash, the driver and passenger occupants should not sit in and/or operate the vehicle, until the head restraint is placed in its proper position. The driver should never adjust the head restraint while the vehicle is in motion. Y our vehicle’ s seats are e[...]

Using the manual recline function (if equipped) Never adjust the driver’ s seat or seatback when the vehicle is moving. Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop. Always drive and ride with your seatback upright and the lap belt snug and low across the hips. Reclining the seatback can cause[...]

Front seat armrest The front seat armrest has a locking pin which prevents the armrest from folding down during a collision. If the locking pin has engaged because of a substantial jolt, but no collision has occurred, you can disengage the locking pin by first moving the armrest forward until it stops to align the hole with the locking pin, then by[...]

Adjusting the power front seats – door mounted controls The controls for the power seats are located on the inside of each front door . Never adjust the driver’ s seat or seatback when the vehicle is moving. Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop. Always drive and ride with your seatba[...]

Press the control to recline the seatback forward or backward. Press to move the seat forward or backward. Press to move the front portion of the seat cushion up or down. 2008 T own Car (tow) Owners Guide (post-2002-fmt) USA (fus) Seating and Safety Restraints 91[...]

Press to move the rear portion of the seat cushion up or down. Heated seats (if equipped) Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury , medication, alcohol use, exhaustion, or other physical conditions, must exercise care when using the seat heater . The seat heater may caus[...]

• Push the indicated side of the control for minimum heat. • Push again to deactivate. The heated seat module resets at every ignition run cycle. While the ignition is in the ON position, activating the high or low heated seat switch enables heating mode. When activated, they will turn off automatically when the ignition is turned to the OFF po[...]

• the key is removed from the ignition cylinder The seat will move forward (to the original position) when: • the transmission is in N (Neutral) or P (Park) • the key is placed in the ignition cylinder Seat-mounted cup holders (if equipped) Y our vehicle may be equipped with cupholders in the cushion of the front center seat and the rear seat[...]

SAFETY RESTRAINTS Personal Safety System™ The Personal Safety System™ provides an improved overall level of frontal crash protection to front seat occupants and is designed to help further reduce the risk of airbag-related injuries. The system is able to analyze different occupant conditions and crash severity before activating the appropriate [...]

Driver and passenger dual-stage airbag supplemental restraints The dual-stage airbags offer the capability to tailor the level of airbag inflation energy . A lower , less forceful energy level is provided for more common, moderate-severity impacts. A higher energy level is used for the most severe impacts. Refer to Airbag supplemental restraints (S[...]

The front passenger sensing system can automatically turn off the front passenger airbag and passenger seat-mounted side airbag. The system is designed to help protect small (child size) occupants from frontal airbag deployments when they are seated or restrained in the front passenger seat contrary to proper child-seating or restraint usage recomm[...]

The Restraints control module (RCM) monitors its own internal circuits and the circuits for the airbag supplemental restraints, crash sensor(s), safety belt pretensioners, front safety belt buckle sensors, front passenger sensing system, and the driver seat position sensor . In addition, the RCM also monitors the restraints warning light in the ins[...]

In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a safety belt. Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one tongue that are designed to be used as a pair . 1) Use the shoulder belt on the outside shoulder only . Never wear the shoul[...]

2. T o unfasten, push the release button and remove the tongue from the buckle. Energy management feature • This vehicle has a safety belt system with an energy management feature at the front outboard seating positions to help further reduce the risk of injury in the event of a head-on collision. • The energy management feature is designed to [...]

Shorten and fasten the belt when not in use. The front outboard and rear safety restraints in the vehicle are combination lap and shoulder belts. The front outboard passenger and rear seat safety belts have three types of locking modes described as follows: V ehicle sensitive mode This is the normal retractor mode, which allows free shoulder belt l[...]

How to use the automatic locking mode • Buckle the combination lap and shoulder belt. • Grasp the shoulder portion and pull downward until the entire belt is pulled out. • Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode. 2008 T own Car (tow) O[...]

How to disengage the automatic locking mode Ford Motor Company recommends that all passenger safety belt assemblies and attaching hardware should be inspected by an authorized dealer after any collision to verify that the ⬙ automatic locking retractor ⬙ feature for child seats is still working properly . Safety belt assemblies should be inspect[...]

Safety belt extension assembly If the safety belt is too short when fully extended, there is a 8 inch (20 cm) safety belt extension assembly that can be added (part number 611C22). This assembly can be obtained from an authorized dealer . Use only extensions manufactured by the same supplier as the safety belt. Manufacturer identification is locate[...]

Safety belt warning light and indicator chime The safety belt warning light illuminates in the instrument cluster and a chime sounds to remind the occupants to fasten their safety belts. Conditions of operation If... Then... The driver’ s safety belt is not buckled before the ignition switch is turned to the ON position... The safety belt warning[...]

If... Then... The driver’ s and front passenger’ s safety belts are buckled before the ignition switch is turned to the ON position or less than 1-2 minutes have elapsed since the ignition switch has been turned ON... The Belt-Minder 威 feature will not activate. The driver’ s or front passenger’ s safety belt is not buckled when the vehic[...]

The following are reasons most often given for not wearing safety belts (All statistics based on U.S. data): Reasons given... Consider ... “Crashes are rare events” 36700 crashes occur every day . The more we drive, the more we are exposed to “rare” events, even for good drivers. 1 in 4 of us will be seriously injured in a crash during our [...]

Reasons given... Consider ... “I have an airbag” Airbags offer greater protection when used with safety belts. Frontal airbags are not designed to inflate in rear and side crashes or rollovers. “I’d rather be thrown clear” Not a good idea. People who are ejected are 40 times more likely to DIE. Safety belts help prevent ejection, WE CAN?[...]

The driver and front passenger Belt-Minder 威 features can be deactivated/activated by performing the following procedure: Before following the procedure, make sure that: • The parking brake is set • The gearshift is in P (Park) • The ignition switch is in the OFF position • The driver and front passenger safety belts are unbuckled While t[...]

AIRBAG SUPPLEMENT AL RESTRAINT SYSTEM (SRS) Important SRS precautions The SRS is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries. Airbags DO NOT inflate slowly; there is a risk of injury from a deploying airbag. All occupants of the vehicle, including the driver , should al[...]

Never place your arm over the air bag module as a deploying air bag can result in serious arm fractures or other injuries. Ford Motor Company recommends that an authorized dealer inspect all steering column assemblies in use in vehicles involved in a collision. Failure to inspect and if necessary replace the steering column assembly could result in[...]

Children and airbags Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position. Failure to follow these instructions may increase the risk of injury in a collision. Airbags can kill or injure a child in a child seat. NEVE[...]

The airbags inflate and deflate rapidly upon activation. After airbag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.g., baking soda) that result from the combustion process that inflates the airbag. Small amo[...]

The diagnostic module monitors its own internal circuits as well as the supplemental airbag electrical system wiring (including the impact sensors), the system wiring, the airbag system readiness light, the airbag back up power and the airbag ignitors. Several air bag system components get hot after inflation. Do not touch them after inflation. If [...]

• a front passenger takes his/her weight off of the seat for a period of time, For side airbag equipped vehicles, the front passenger sensing system will turn off the passenger seat side airbag if: • the seat is empty and safety belt is unbuckled. The front passenger sensing system uses a ⬙ passenger airbag off ⬙ or ⬙ pass airbag off ⬙ [...]

• Have the person sit upright in the seat, centered on the seat cushion, with the person’ s legs comfortably extended. • Restart the vehicle and have the person remain in this position for about two minutes. This will allow the system to detect that person and enable the passenger’ s frontal airbag. • If the indicator lamp remains lit eve[...]

The front passenger sensing system may detect small or medium objects placed on the seat cushion. For most objects that are in the front passenger seat, the passenger airbag will be disabled. Even though the passenger airbag is disabled, the ⬙ pass airbag off ⬙ lamp may or may not be illuminated according to the table below . Objects Pass Airba[...]

T o reduce the risk of possible serious injury: Do not stow objects in seat back map pocket (if equipped) or hang objects off seat back if a child is in the front passenger seat. Do not place objects underneath the front passenger seat or between the seat and the center console (if equipped). Check the “passenger airbag off” or “pass airbag o[...]

An out of position front center occupant could affect the decision of the front passenger sensing system. If it is necessary to modify an advanced front airbag system to accommodate a person with disabilities, contact the Ford Customer Relationship Center at the phone number shown in the Customer Assistance section of this Owner’ s Guide . Any al[...]

Do not use accessory seat covers. The use of accessory seat covers may prevent the deployment of the side airbags and increase the risk of injury in an accident. Do not lean your head on the door . The side airbag could injure you as it deploys from the side of the seatback. Do not attempt to service, repair , or modify the airbag SRS, its fuses or[...]

The side airbags are fitted on the outboard side of the seatbacks of the front seats. In certain lateral collisions, the airbag on the side affected by the collision will be inflated. The airbag was designed to inflate between the door panel and occupant to further enhance the protection provided occupants in side impact collisions. The airbag SRS [...]

• A series of five beeps will be heard. The tone pattern will repeat periodically until the problem and/or light are repaired. If any of these things happen, even intermittently , have the SRS serviced at your authorized dealer immediately . Unless serviced, the system may not function properly in the event of a collision. Disposal of airbags and[...]

If the shoulder belt portion of a combination lap and shoulder belt can be positioned so it does not cross or rest in front of the child’ s face or neck, the child should wear the lap and shoulder belt. Moving the child closer to the center of the vehicle may help provide a good shoulder belt fit. Do not leave children, unreliable adults, or pets[...]

• Is the shoulder belt centered on the shoulder and chest? • Can the child stay seated like this for the whole trip? T ypes of booster seats There are two types of belt-positioning booster seats: • Those that are backless. If your backless booster seat has a removable shield, remove the shield and use the lap/shoulder belt. If a seating posit[...]

Children and booster seats vary widely in size and shape. Choose a booster that keeps the lap belt low and snug across the hips, never up across the stomach, and lets you adjust the shoulder belt to cross the chest and rest snugly near the center of the shoulder . The drawings below compare the ideal fit (center) to a shoulder belt uncomfortably cl[...]

Never use pillows, books, or towels to boost a child. They can slide around and increase the likelihood of injury or death in a collision. SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of the child. Carefully follow all of the manufacturer’ s instructions with the sa[...]

Ford Motor Company recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position with LA TCH and tether anchors. For more information on top tether straps and anchors, refer to Attaching child safety seats with tether straps in this chapter . For more information of LA TCH anchors refer to [...]

2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together . 3. While holding the shoulder and lap belt portions together , route the tongue through the child seat according to the child seat manufacturer’ s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle (the b[...]

5. T o put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is pulled out and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode. 7. Pull the lap belt portion across the child seat toward the buc[...]

Attaching child safety seats with tether straps Most new forward-facing child safety seats include a tether strap which goes over the back of the seat and hooks to an anchoring point. T ether straps are available as an accessory for many older safety seats. Contact the manufacturer of your child seat for information about ordering a tether strap. T[...]

4. Open the tether anchor cover . 5. Clip the tether strap to the anchor as shown. If the tether strap is clipped incorrectly , the child safety seat may not be retained properly in the event of a collision. 6. Install the child safety seat tightly using the LA TCH anchors or safety belts. Follow the instructions in this chapter . 7. T ighten the c[...]

Y our vehicle has LA TCH anchors for child seat installation at the seating positions marked with the child seat symbol. The anchors on both sides of the center of the rear seat are provided for child seats at the outboard seats, and are further apart than the pairs of lower anchors for child seat installation at other seats. DO NOT install child s[...]

If you install a child seat with rigid LA TCH attachments, do not tighten the tether strap enough to lift the child seat off the vehicle seat cushion when the child is seated in it. Keep the tether strap just snug without lifting the front of the child seat. Keeping the child seat just touching the vehicle seat gives the best protection in a severe[...]

INFORMA TION ABOUT UNIFORM TIRE QUALITY GRADING T ire Quality Grades apply to new pneumatic passenger car tires. The Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: • T readwear 200 T raction AA T emperature A These T ire Quality Grades are determined by standards th[...]

The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics. T emperature A B C The temperature grades are A (the highest), B and C, representing the tire’ s resistance to the generation of heat and its ability to dissipate [...]

• Extra load: A class of P-metric or Metric tires designed to carry a heavier maximum load at 41 psi [43 psi (2.9 bar) for Metric tires]. Increasing the inflation pressure beyond this pressure will not increase the tire’ s load carrying capability . • kPa: Kilopascal, a metric unit of air pressure. • PSI: Pounds per square inch, a standard [...]

Use the recommended cold inflation pressure for optimum tire performance and wear . Under -inflation or over -inflation may cause uneven treadwear patterns. Under -inflation is the most common cause of tire failures and may result in severe tire cracking, tread separation or ⬙ blowout ⬙ , with unexpected loss of vehicle control and increased ri[...]

Note: If you have to drive a distance to get air for your tire(s), check and record the tire pressure first and add the appropriate air pressure when you get to the pump. It is normal for tires to heat up and the air pressure inside to go up as you drive. 2. Remove the cap from the valve on one tire, then firmly press the tire gauge onto the valve [...]

Tire wear When the tread is worn down to 1/16th of an inch (2 mm), tires must be replaced to help prevent your vehicle from skidding and hydroplaning. Built-in treadwear indicators, or “wear bars”, which look like narrow strips of smooth rubber across the tread will appear on the tire when the tread is worn down to 1/16th of an inch (2 mm). Whe[...]

U.S. DOT Tire Identification Number (TIN) Both U.S. and Canada Federal regulations require tire manufacturers to place standardized information on the sidewall of all tires. This information identifies and describes the fundamental characteristics of the tire and also provides a U.S. DOT T ire Identification Number for safety standard certification[...]

When mounting replacement tires and wheels, you should not exceed the maximum pressure indicated on the sidewall of the tire to set the beads without additional precautions listed below . If the beads do not seat at the maximum pressure indicated, re-lubricate and try again. When inflating the tire for mounting pressures up to 20 psi greater than t[...]

• A void potholes and objects on the road • Do not run over curbs or hit the tire against a curb when parking If your vehicle is stuck in snow , mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to five seconds. Do not spin the wheels at over 35 [...]

Tire rotation Rotating your tires at the recommended interval (as indicated in the scheduled maintenance information that comes with your vehicle) will help your tires wear more evenly , providing better tire performance and longer tire life. • Rear Wheel Drive (RWD) vehicles/Four Wheel Drive (4WD)/All Wheel Drive (A WD) vehicles (front tires at [...]

INFORMATION CONTAINED ON THE TIRE SIDEWALL Both U.S. and Canada Federal regulations require tire manufacturers to place standardized information on the sidewall of all tires. This information identifies and describes the fundamental characteristics of the tire and also provides a U.S. DOT T ire Identification Number for safety standard certificatio[...]

7. H: Indicates the tire’ s speed rating. The speed rating denotes the speed at which a tire is designed to be driven for extended periods of time under a standard condition of load and inflation pressure. The tires on your vehicle may operate at different conditions for load and inflation pressure. These speed ratings may need to be adjusted for[...]

10. T ire Ply Composition and Material Used: Indicates the number of plies or the number of layers of rubber -coated fabric in the tire tread and sidewall. T ire manufacturers also must indicate the ply materials in the tire and the sidewall, which include steel, nylon, polyester , and others. 11. Maximum Load: Indicates the maximum load in kilogra[...]

Additional information contained on the tire sidewall for “L T” type tires “L T” type tires have some additional information beyond those of “P” type tires; these differences are described below . Note: T ire Quality Grades do not apply to this type of tire. 1. LT: Indicates a tire, designated by the T ire and Rim Association (T&RA)[...]

Information on “T” type tires “T” type tires have some additional information beyond those of “P” type tires; these differences are described below: T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example. T ire Quality Grades do not apply to this type of tire. 1. T: Ind[...]

TIRE PRESSURE MONITORING SYSTEM (TPMS) Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard[...]

The T ire Pressure Monitoring System complies with part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. The T ire Pre[...]

Understanding your Tire Pressure Monitoring System (TPMS) The T ire Pressure Monitoring System measures pressure in your four road tires and sends the tire pressure readings to your vehicle. The Low T ire W arning Lamp will turn ON if the tire pressure is significantly low . Once the light is illuminated, your tires are under inflated and need to b[...]

Low T ire Pressure W arning Light Possible cause Customer Action Required Solid W arning Light T ire(s) under -inflated 1. Check your tire pressure to ensure tires are properly inflated; refer to Inflating your tires in this chapter . 2. After inflating your tires to the manufacturer’ s recommended inflation pressure as shown on the T ire Label ([...]

Low T ire Pressure W arning Light Possible cause Customer Action Required Flashing W arning Light Spare tire in use Y our temporary spare tire is in use. (This includes the optional full-sized matching wheel and tire). Repair the damaged road wheel and re-mount it on the vehicle to restore system functionality . For a description of how the system [...]

ON, visually check each tire to verify that no tire is flat. (If one or more tires are flat, repair as necessary .) Check air pressure in the road tires. If any tire is under -inflated, carefully drive the vehicle to the nearest location where air can be added to the tires. Inflate all the tires to the recommended inflation pressure. SNOW TIRES AND[...]

V EHICLE LOADING – WITH AND WITHOUT A TRAILER This section will guide you in the proper loading of your vehicle and/or trailer , to keep your loaded vehicle weight within its design rating capability , with or without a trailer . Properly loading your vehicle will provide maximum return of vehicle design performance. Before loading your vehicle, [...]

Example only: Cargo W eight – includes all weight added to the Base Curb W eight, including cargo and optional equipment. When towing, trailer tongue load weight is also part of cargo weight. GA W (Gross Axle W eight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload. 2008 T own Car (to[...]

GA WR (Gross Axle W eight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Label located on the B-Pillar or the edge of the driver’ s door . The total load on each axle must never exceed its GA WR. Note: For trailer towing information r[...]

GCW (Gross Combined W eight) – is the weight of the loaded vehicle (GVW) plus the weight of the fully loaded trailer . GCWR (Gross Combined W eight Rating) – is the maximum allowable weight of the vehicle and the loaded trailer – including all cargo and passengers – that the vehicle can handle without risking damage. (Important: The towing [...]

Steps for determining the correct load limit: 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs.” on your vehicle’ s placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle. 3. Subtract the combined weight of the driver and passengers fr[...]

calculation would be: 635 kg - (2 x 99 kg) - (12 x 45 kg) = 635 - 198 - 540 = -103 kg. Y ou will need to reduce the load weight by at least 240 lb. (104 kg). If you remove 3-100 lb. (45 kg) cement bags, then the load calculation would be: 1,400 - (2 x 220) - (9 x 100) = 1,400 - 440 - 900 = 60 lb. Now you have the load capacity to transport the ceme[...]

Safety chains Always connect the trailer’ s safety chains to the frame or hook retainers of the vehicle hitch. T o connect the trailer’ s safety chains, cross the chains under the trailer tongue and allow slack for turning corners. If you use a rental trailer , follow the instructions that the rental agency gives to you. Do not attach safety ch[...]

• Anticipate stops and brake gradually . • Do not exceed the GCWR rating or transmission damage may occur . Servicing after towing If you tow a trailer for long distances, your vehicle will require more frequent service intervals. Refer to your scheduled maintenance information for more information. T railer towing tips • Practice turning, st[...]

• do not allow waves to break higher than 6 inches (15 cm) above the bottom edge of the rear bumper . Exceeding these limits may allow water to enter vehicle components: • causing internal damage to the components. • affecting driveability , emissions and reliability . Replace the rear axle lubricant any time the axle has been submerged in wa[...]

STARTING Positions of the ignition 1. OFF/LOCK, shuts off the engine and all accessories/locks the gearshift lever and allows key removal. 2. ACC, allows the electrical accessories such as the radio to operate while the engine is not running. 3. ON, all electrical circuits operational. W arning lights illuminated. Key position when driving. 4. ST A[...]

Do not start your vehicle in a closed garage or in other enclosed areas. Exhaust fumes can be toxic. Always open the garage door before you start the engine. See Guarding against exhaust fumes in this chapter for more instructions. If you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle immediately . Do not drive if yo[...]

5. T urn the key to 3 (ON) without turning the key to 4 (ST ART). Some warning lights will briefly illuminate. See W arning lights and chimes in the Instrument Cluster chapter for more information regarding the warning lights. Starting the engine 1. T urn the key to 3 (ON) without turning the key to 4 (ST ART). 2. T urn the key to 4 (ST ART), then [...]

Y ou may experience a decrease in peak performance when the engine is cold when operating on E 85 ethanol. Do not crank the engine for more than 30 seconds at a time as starter damage may occur . If the engine fails to start, turn the key to OFF and wait 30 seconds before trying again. Do not use starting fluid such as ether in the air intake syste[...]

ENGINE BLOCK HEATER (IF EQUIPPED) An engine block heater warms the engine coolant which aids in starting and allows the heater/defroster system to respond quickly . If your vehicle is equipped with this system, your equipment includes a heater element which is installed in your engine block and a wire harness which allows the user to connect the sy[...]

• Make sure that when in operation, the extension cord plug /engine block heater cord plug connection is free and clear of water in order to prevent possible shock or fire. • Be sure that areas where the vehicle is parked are clean and clear of all combustibles such as petroleum products, dust, rags, paper and similar items. • Be sure that th[...]

Four-wheel anti-lock brake system (ABS) Y our vehicle is equipped with an Anti-lock Braking System (ABS). This system helps you maintain steering control during emergency stops by keeping the brakes from locking. Noise from the ABS pump motor and brake pedal pulsation may be observed during ABS braking and the brake pedal may suddenly travel a litt[...]

Parking brake with auto-release Apply the parking brake whenever the vehicle is parked. T o set the parking brake: 1. Move the gearshift to P (Park). 2. Push pedal downward. The BRAKE warning lamp in the instrument cluster illuminates and remains illuminated (when the ignition is turned ON) until the parking brake is fully released. Always set the [...]

If the parking brake fails to release after completing this procedure, use the manual parking brake release lever . Pull the lever to manually release the parking brake. T RACTION CONTROL™ For T raction Control™ warning lights refer to W arning lights and chimes in the Instrument cluster chapter . Y our vehicle is equipped with a T raction Cont[...]

Aggressive driving in any road conditions can cause you to lose control of your vehicle increasing the risk of severe personal injury or property damage. The occurrence of a T raction Control™ event is an indication that at least some of the tires have exceeded their ability to grip the road; this may lead to an increased risk of loss of vehicle [...]

AIR SUSPENSION SYSTEM The air suspension system is designed to improve ride, handling and general vehicle performance during: • Certain road conditions • Steering maneuvers • Braking • Accelerations This system keeps the rear of your vehicle at a constant level by automatically adding air or releasing air from the springs. If you exceed the[...]

has blown or the vehicle’ s brakelamps are not operating properly . Refer to Fuses and relays in the Roadside Emergencies chapter . If the fuse is not blown, perform the following procedure: 1. Apply the parking brake, turn the ignition to 2 (ACC). 2. Locate the access plug on the underside of the steering column cover . 3. Remove the access plug[...]

Driving with a 4–speed automatic transmission Understanding the gearshift positions of the 4–speed automatic transmission P (Park) This position locks the transmission and prevents the rear wheels from turning. T o put your vehicle in gear: • Start the engine • Depress the brake pedal • Move the gearshift lever into the desired gear T o p[...]

(Overdrive) The normal driving position for the best fuel economy . T ransmission operates in gears one through four . Overdrive can be deactivated by pressing the transmission control switch on the gearshift lever . Drive (not shown) Drive is activated when the transmission control switch is pressed. • This position allows for all forward gears [...]

Forced downshifts • Allowed in (Overdrive) or Drive. • Depress the accelerator to the floor . • Allows transmission to select an appropriate gear . If your vehicle gets stuck in mud or snow If your vehicle gets stuck in mud or snow , it may be rocked out by shifting between forward and reverse gears, stopping between shifts in a steady patter[...]

Certain add-on devices such as large trailer hitches, bike or surfboard racks and any device that may block the normal detection zone of the reverse sensing system may create false beeps. The system will assist the driver in detecting certain objects while the vehicle moves in reverse at speeds less than 6 mph (10 km/h). The system is not effective[...]

Audible W arnings Distance to Object W arning Speed above 2.5 mph (4 km/h) up to 1.6 feet (.5 meters) Solid 1.6 feet (.5 meters) to 3.1 feet (1 meter) Fast beep 3.1 feet (1 meter) to 5.7 feet (1.8 meters) Medium/fast beep 5.7 feet (1.8 meters) to 9 feet (2.8 meters) Medium beep 9 feet (2.8 meters) to 13 feet (4 meters) Medium/slow beep 13 feet (4 m[...]

DRIVING THROUGH WATER If driving through deep or standing water is unavoidable, proceed very slowly especially when the depth is not known. Never drive through water that is higher than the bottom of the wheel rims (for cars) or the bottom of the hubs (for trucks). When driving through water , traction or brake capability may be limited. Also, wate[...]

ROADSIDE ASSISTANCE Getting roadside assistance T o fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program. This program is separate from the New V ehicle Limited W arranty . The service is available: • 24–hours, seven days a week • for the coverage period listed on the Roadsi[...]

Canadian customers refer to your Customer Information Guide for information on: • coverage period • exact fuel amounts • towing of your disabled vehicle • emergency travel expense reimbursement • travel planning benefits Using roadside assistance Complete the roadside assistance identification card and place it in your wallet for quick re[...]

HAZARD FLASHER CONTROL The hazard flasher is located on the steering column, just behind the steering wheel. The hazard flashers will operate when the ignition is in any position or if the key is not in the ignition. Push in the flasher control and all front and rear direction signals will flash. Press the flasher control again to turn them off. Us[...]

4. T urn the ignition to the ON position. Pause for a few seconds and return the key to the OFF/LOCK position. 5. Make a further check for leaks in the fuel system. FUSES AND RELAYS Fuses If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are identified by a broken wire within the fuse. Check the appropriate[...]

Passenger compartment fuse panel The fuse panel is located below and to the left of the steering wheel by the brake pedal. Remove the panel cover to access the fuses. T o remove a fuse use the fuse puller tool provided on the fuse panel cover . The fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Desc[...]

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 6 10A Passive Anti-Theft System (P A TS), Powertrain Control Module (PCM) relay coil, Ignition relay coil, Fuel relay coil 7 10A Wiper module 8 10A Power Decklid Module (PDM), Overdrive cancel switch, Cluster , Compass module, LCM 9 7.5A Mirror switch illumination, Doo[...]

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 23 10A LCM 24 15A LCM (High beams), Multi-function switch (Flash-to-pass) 25 10A DA TC module, Cluster 26 15A LCM (Park lamps, cornering lamps, license lamps) 27 — Not used 28 7.5A Brake signal, LCM (BTSI), ABS 29 — Not used 30 — Not used 31 5A LCM (Key in) 32 7.[...]

The high-current fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 1 30A* Ignition switch 2 20A* Rear heated seats 3 10A* Powertrain Control Module (PCM) keep alive power and canister vent 4 20A* Fuel relay feed 5 20A* Instrument panel power point 6 15A* Alternator regulator 7 30A* PCM relay feed 8 2[...]

Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 13 10A* Rear air suspension module (RASM) 14 20A* Stop lamp switch 15 15A* Lumbar , Fuel door 16 20A* Heated seats 17 – Not used 18 – Not used 19 15A* Injectors 20 15A* PCM 21 15A* Powertrain loads and sensors 22 — Not used 23 10A* Heated mirrors 24 – Not used 101 40A** [...]

Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description K201 Micro relay A/C clutch K202 — Not used K203 Micro relay Ignition coil K204 Micro relay PCM K205 — Not used K206 Micro relay Fuel K207 — Not used K208 — Not used K209 Micro relay Horn K301 Mini relay Starter K302 Mini relay RASM (Air compressor) K303 Mini relay Blowe[...]

The use of tire sealants may damage your T ire Pressure Monitoring System and should not be used. Refer to T ire Pressure Monitoring System (TPMS) in the T ires, Wheels and Loading chapter for important information. If the tire pressure monitor sensor becomes damaged, it will no longer function. Dissimilar spare tire/wheel information Failure to fo[...]

Use of one of the dissimilar spare tires listed above at any one wheel location can lead to impairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs • W inter weather driving capability • W et weather driving capability 3. Full-size dissimilar spare without labe[...]

Full-size Matching Spare Tire/Wheel Information This spare tire/wheel will match the road tire/wheel. When driving with the full size matching spare tire/wheel, do not exceed 70 mph (113 km/h). It is intended for temporary use only . This means if you need to use it, you should replace it as soon as possible. Tire change procedure Note: If your veh[...]

1. Park on a level surface, activate hazard flashers and set parking brake. 2. Place gearshift lever in P (Park), turn engine OFF and block the diagonally opposite wheel. 3. Remove the spare tire and the jack. The jack may be located: • A – behind the mini spare tire or • B – behind the full size spare tire. On vehicles equipped with Air Su[...]

4. Remove the lug wrench (A) from the jack. Rotate the lug wrench socket out from the handle. 5. Locate pry off notch (if equipped) and remove the center ornament from the aluminum wheel with the tapered end of the wheel nut wrench that came with your vehicle. Insert and twist the handle, then pry against the wheel. 6. Loosen each wheel lug nut one[...]

JACK LOCA TION-REAR The jack location markings can be found on the lower outer edge of the body . • Locate the jack locator mark (B - triangle ) on the body (C) near the tire you are changing, then place the jack (D) under the frame (A) of the vehicle aligning it with the mark (B - triangle ). • Position the jack according to the following guid[...]

10. Remove the jack and fully tighten the lug nuts in the order shown. Refer to Wheel lug nut torque specifications later in this chapter for the proper lug nut torque specification. 11. Put flat tire, jack and lug wrench away . Be sure to stow the jack properly in the holder bracket. 12. T urn on the air suspension switch. WHEEL LUG NUT TORQUE SPE[...]

Note: Inspect the wheel pilot hole prior to installation. If there is visible corrosion in wheel pilot hole, remove loose particles by wiping with clean rag and apply grease. Apply grease only to the wheel pilot hole surface by smearing a “dime” (1 square cm) sized glob of grease around the wheel pilot surface (1) with end of finger . DO NOT ap[...]

4. Check all battery terminals and remove any excessive corrosion before you attach the battery cables. Ensure that vent caps are tight and level. 5. T urn the heater fan on in both vehicles to protect from any electrical surges. T urn all other accessories off. Connecting the jumper cables 1. Connect the positive (+) jumper cable to the positive ([...]

3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery . 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’ s engine, away from the battery and the carburetor/fuel injection system. Do not use fuel lines, engine rocker covers or the intake manifold as grounding [...]

Jump starting 1. Start the engine of the booster vehicle and run the engine at moderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for an additional three minutes before disconnecting the jumper cables. Removing the jumper cables Remove the jumper cables in the rev[...]

3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’ s battery . 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’ s battery . After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle c[...]

WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or , if you are a member of a roadside assistance program, your roadside assistance service provider . It is recommended that your vehicle be towed with a wheel lift or flatbed equipment. Do not tow with a slingbelt. Ford Motor Company has not approved a sl[...]

Emergency T owing In case of a roadside emergency with a disabled vehicle (without access to wheel dollies, car hauling trailer , or flatbed transport vehicle) your vehicle (regardless of transmission powertrain configuration) can be flat towed (all wheels on the ground) under the following conditions: • V ehicle is facing forward. • Place the [...]

GETTING THE SERVICES YOU NEED At home Y ou must take your Lincoln or Mercury vehicle to an authorized dealer for warranty repairs. While any authorized dealer handling your vehicle line will provide warranty service, we recommend you return to your selling authorized dealer who wants to ensure your continued satisfaction. Please note that certain w[...]

In Canada: Customer Relationship Centre Ford Motor Company of Canada, Limited P .O. Box 2000 Oakville, Ontario L6J 5E4 1-800-565-3673 (FORD) www .ford.ca If you own a Lincoln vehicle and are away from home when your vehicle needs service, or if you need more help than the authorized dealer could provide, after following the steps described above, c[...]

In some states (in the U.S.) you must directly notify Ford in writing before pursuing remedies under your state’ s warranty laws. Ford is also allowed a final repair attempt in some states. In the United States, a warranty dispute must be submitted to the BBB AUTO LINE before taking action under the Magnuson-Moss W arranty Act, or to the extent a[...]

THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM (U.S. ONLY) Y our satisfaction is important to Ford Motor Company and to your dealer . Experience has shown that our customers have been very successful in achieving satisfaction by following the three-step procedure outlined on the front page of the W arranty Guide. However , if your warranty conc[...]

UTILIZING THE MEDIATION/ARBITRATION PROGRAM (CANADA ONLY) For vehicles delivered to authorized Canadian dealers. In those cases where you continue to feel that the efforts by Ford of Canada and the authorized dealer to resolve a factory-related vehicle service concern have been unsatisfactory , Ford of Canada participates in an impartial third part[...]

If you did not take advantage of the Ford Extended Service Plan at the time of purchasing your vehicle, you may still be eligible. Since this information is subject to change, please ask your authorized dealer for complete details about Ford Extended Service Plan coverage options, or visit the Ford ESP website at www .ford-esp.com. GETTING ASSIST A[...]

ORDERING ADDITIONAL OWNER’S LITERA TURE T o order the publications in this portfolio, contact Helm, Incorporated at: HELM, INCORPORA TED P .O. Box 07150 Detroit, Michigan 48207 Or call: For a free publication catalog, order toll free: 1-800-782-4356 Monday-Friday 8:00 a.m. - 6:00 p.m. EST Helm, Incorporated can also be reached by their website: w[...]

T o contact NHTSA, you may call the V ehicle Safety Hotline toll-free at 1–888–327–4236 (TTY : 1–800–424–9153); go to http://www.safercar .gov; or write to: Administrator 1200 New Jersey A venue, Southeast W ashington, D.C. 20590 Y ou can also obtain other information about motor vehicle safety from http://www.safercar .gov. REPORTING S[...]

W ASHING THE EXTERIOR W ash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo, such as Motorcraft Detail W ash (ZC-3-A), which is available from your authorized dealer . • Never use strong household detergents or soap, such as dish washing or laundry liquid. These products can discolor and spot painted surfaces. • Neve[...]

W AXING • W ash the vehicle first. • Do not use waxes that contain abrasives; use Motorcraft Premium Liquid W ax (ZC-53-A), which is available from your authorized dealer , or an equivalent quality product. • Do not allow paint sealant to come in contact with any non-body (low-gloss black) colored trim, such as grained door handles, roof rack[...]

ENGINE Engines are more efficient when they are clean because grease and dirt buildup keep the engine warmer than normal. When washing: • T ake care when using a power washer to clean the engine. The high-pressure fluid could penetrate the sealed parts and cause damage. • Do not spray a hot engine with cold water to avoid cracking the engine bl[...]

WINDOWS AND WIPER BLADES The windshield, rear and side windows and the wiper blades should be cleaned regularly . If the wipers do not wipe properly , substances on the vehicle’ s glass or the wiper blades may be the cause. These may include hot wax treatments used by commercial car washes, water repellent coatings, tree sap, or other organic con[...]

• Be certain to wash or wipe your hands clean if you have been in contact with certain products such as insect repellent and suntan lotion in order to avoid possible damage to the interior painted surfaces. • Do not use household or glass cleaners as these may damage the finish of the instrument panel, interior trim and cluster lens. Do not use[...]

Do not use cleaning solvents, bleach or dye on the vehicle’ s safety belts, as these actions may weaken the belt webbing. On vehicles equipped with seat-mounted airbags, do not use chemical solvents or strong detergents. Such products could contaminate the side-airbag system and affect performance of the side airbag in a collision. LEATHER SEATS [...]

FORD AND LINCOLN MERCURY CAR CARE PRODUCTS Y our Ford or Lincoln Mercury authorized dealer has many quality products available to clean your vehicle and protect its finishes. These quality products have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and appearance of your vehicle. Eac[...]

SERVICE RECOMMENDATIONS T o help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy . If your vehicle requires professional service, your authorized dealer can provide the necessary parts and service. Check your W arranty Guide to find out which parts and services are covered. Use only r[...]

OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the instrument panel. 2. Go to the front of the vehicle and release the auxiliary latch that is located in the grille. 3. Lift the hood until the lift cylinders hold it open. 2008 T own Car (tow) Owners Guide (post-2002-fmt) USA (fus) Maintenance and Specifications 2[...]

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4.6L SOHC V8 engine 1. W indshield washer fluid reservoir 2. Engine oil filler cap 3. Automatic transmission fluid dipstick 4. Brake fluid reservoir 5. Air filter assembly 6. Engine oil dipstick (access behind air tube) 7. Power steering fluid reservoir 8. Engine coolant reservoir 9. Power distributi[...]

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if the level is low . In very cold weather , do not fill the reservoir completely . Only use a washer fluid that meets Ford specifications. Do not use any special washer fluid such as windshield water repellent type fluid or bug wash. They may cause squeaking, chatter noise, streaking and smea[...]

CHANGING THE WIPER BLADES 1. Pull the wiper blade and arm away from the glass. T urn the blade as much as possible to gain access to the lock tab (A). Using a skinny tool, push the lock tab (A) to release the blade from the arm loop and pull the blade from the arm. 2. Attach the new blade to the arm loop and pull it into place until a click is hear[...]

5. Locate and carefully remove the engine oil level dipstick. 6. W ipe the dipstick clean. Insert the dipstick fully , then remove it again. • If the oil level is within this range, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below this mark, engine oil must be added to raise the level within the normal operating range. ?[...]

7. Put the dipstick back in and ensure it is fully seated. Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter . 2. If the engine oil level is not within the normal operating range, add only certified engine oil of the recommended viscosity . Remove the engine oil filler cap and use a funnel[...]

Do not use supplemental engine oil additives, cleaners or other engine treatments. They are unnecessary and could lead to engine damage that is not covered by Ford warranty . Change your engine oil and filter according to the appropriate schedule listed in scheduled maintenance information. Ford production and aftermarket (Motorcraft) oil filters a[...]

Batteries normally produce explosive gases which can cause personal injury . Therefore, do not allow flames, sparks or lighted substances to come near the battery . When working near the battery , always shield your face and protect your eyes. Always provide proper ventilation. When lifting a plastic-cased battery , excessive pressure on the end wa[...]

• The vehicle may need to be driven 10 miles (16 km) or more to relearn the idle and fuel trim strategy . • If you do not allow the engine to relearn its idle trim, the idle quality of your vehicle may be adversely affected until the idle trim is eventually relearned. If the battery has been disconnected or a new battery has been installed, the[...]

When the engine is cold, check the level of the engine coolant in the reservoir . • The engine coolant should be at the “FULL COLD” level or within the “COLD FILL RANGE” as listed on the engine coolant reservoir (depending upon application). • Refer to scheduled maintenance information for service interval schedules. • Be sure to read[...]

Do not add engine coolant when the engine is hot. Steam and scalding liquids released from a hot cooling system can burn you badly . Also, you can be burned if you spill coolant on hot engine parts. Do not put engine coolant in the windshield washer fluid container . If sprayed on the windshield, engine coolant could make it difficult to see throug[...]

coolant degas system with a pressurized cap, or if it is necessary to remove the coolant pressure relief cap on the radiator of a vehicle with an overflow system, follow these steps to add engine coolant. T o reduce the risk of personal injury , make sure the engine is cool before unscrewing the coolant pressure relief cap. The cooling system is un[...]

Recycled engine coolant Ford Motor Company does NOT recommend the use of recycled engine coolant in vehicles originally equipped with Motorcraft Premium Gold Engine Coolant since a Ford-approved recycling process is not yet available. Used engine coolant should be disposed of in an appropriate manner . Follow your community’ s regulations and sta[...]

• Refer to the chart on the coolant container to ensure the coolant concentration in your vehicle will provide adequate protection at the temperatures in which you drive. V ehicles driven year -round in non-extreme climates should use a 50/50 mixture of engine coolant and distilled water for optimum cooling system and engine protection. What you [...]

2. Arrange for the vehicle to be taken to an authorized dealer . 3. If this is not possible, wait a short period for the engine to cool. 4. Check the coolant level and replenish if low . Never remove the coolant reservoir cap while the engine is running or hot. 5. Re-start the engine and take your vehicle to an authorized dealer . Driving the vehic[...]

Fuel ethanol and gasoline may contain benzene, which is a cancer -causing agent. Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials and any open flames before fueling your vehicle. • Always turn off the vehicle before fueling. • Automotive fuels can be harmful or fatal if swallowed. Fuels such a[...]

Pure ethanol is the alcohol which is the intoxicating agent in liquor , beer and wine. It is distilled from the fermentation of plants such as field corn and sugar cane. When ethanol is produced for use in motor fuels, a small amount of gasoline is added to make it unfit for beverage use. The resulting ethanol blend is called denatured fuel ethanol[...]

Refueling Fuel vapor burns violently and a fuel fire can cause severe injuries. T o help avoid injuries to you and others: • Read and follow all the instructions on the pump island; • T urn off your engine when you are refueling; • Do not smoke if you are near fuel or refueling your vehicle; • Keep sparks, flames and smoking materials away [...]

At the next opportunity , safely pull off of the road, remove the fuel filler cap, align the cap properly and reinstall it. The check fuel cap light or “check fuel cap” message may not reset immediately; it may take several driving cycles for the check fuel cap light or “check fuel cap” message to turn off. A driving cycle consists of an en[...]

Y our vehicle was not designed to use fuel or fuel additives with metallic compounds, including manganese-based additives. Studies indicate that these additives can cause your vehicle’ s emission control system to deteriorate more rapidly . Repairs to correct the effects of using a fuel for which your vehicle was not designed may not be covered b[...]

Do not add aftermarket fuel additive products to your fuel tank. It should not be necessary to add any aftermarket products to your fuel tank if you continue to use high quality fuel of the recommended octane rating. These products have not been approved for your engine and could cause damage to the fuel system. Repairs to correct the effects of us[...]

• The Service engine soon indicator may come on. For more information on the Service engine soon indicator , refer to W arning lights and chimes in the Instrument Cluster chapter . ESSENTIALS OF GOOD FUEL ECONOMY Measuring techniques Y our best source of information about actual fuel economy is you, the driver . Y ou must gather information as ac[...]

• Have the vehicle loading and distribution the same every time. Y our results will be most accurate if your filling method is consistent. Calculating fuel economy 1. Fill the fuel tank completely and record the initial odometer reading (in miles or kilometers). 2. Each time you fill the tank, record the amount of fuel added (in gallons or liters[...]

• Revving the engine before turning it off may reduce fuel economy . • Using the air conditioner or defroster may reduce fuel economy . • Y ou may want to turn off the speed control in hilly terrain if unnecessary shifting between the top gears occurs. Unnecessary shifting of this type could result in reduced fuel economy . • W arming up a [...]

EP A window sticker Every new vehicle should have the EP A window sticker . Contact your authorized dealer if the window sticker is not supplied with your vehicle. The EP A window sticker should be your guide for the fuel economy comparisons with other vehicles. It is important to note the box in the lower left corner of the window sticker . These [...]

An improperly operating or damaged exhaust system may allow exhaust to enter the vehicle. Have a damaged or improperly operating exhaust system inspected and repaired immediately . Exhaust leaks may result in entry of harmful and potentially lethal fumes into the passenger compartment. Do not make any unauthorized changes to your vehicle or engine.[...]

If the Service engine soon indicator remains on, have your vehicle serviced at the first available opportunity . Although some malfunctions detected by the OBD-II may not have symptoms that are apparent, continued driving with the Service engine soon indicator on can result in increased emissions, lower fuel economy , reduced engine and transmissio[...]

POWER STEERING FLUID Check the power steering fluid. Refer to scheduled maintenance information for the service interval schedules. 1. Start the engine and let it run until it reaches normal operating temperature (the engine coolant temperature gauge indicator will be near the center of the normal area between H and C). 2. While the engine idles, t[...]

BRAKE FLUID The fluid level will drop slowly as the brakes wear , and will rise when the brake components are replaced. Fluid levels below the “MAX” line that do not trigger the brake system warning lamp are within the normal operating range, there is no need to add fluid. If the fluid levels are outside of the normal operating range, the perfo[...]

Low fluid level Do not drive the vehicle if the fluid level is at the bottom of the dipstick and the ambient temperature is above 50°F (10°C). Correct fluid level The transmission fluid should be checked at normal operating temperature 150°F-170°F (66°C-77°C) on a level surface. The normal operating temperature can be reached after approximat[...]

Use of a non-approved automatic transmission fluid may cause internal transmission component damage. If necessary , add fluid in 1/2 pint (250 ml) increments through the filler tube until the level is correct. If an overfill occurs, excess fluid should be removed by an authorized dealer . An overfill condition of transmission fluid may cause shift [...]

5. Install a new air filter element. Be careful not to crimp the filter element edges between the air filter housing and cover . This could cause filter damage and allow unfiltered air to enter the engine if not properly seated. 6. Replace the air filter housing cover and secure the clamps. 7. Replace the air inlet tube and secure the clamp. Note: [...]

Replace the PCV valve with one that meets Ford material and design specifications for your vehicle, such as a Motorcraft or equivalent replacement part. The customer warranty may be void for any damage to the emissions system if such a PCV valve is not used. 3 For spark plug replacement, see your authorized dealer . Refer to scheduled maintenance i[...]

MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIES Item Capacity Ford part name Ford part number / Ford specification Brake fluid Between MIN and MAX on reservoir Motorcraft High Performance DOT 3 Motor V ehicle Brake Fluid 1 PM-1-C / WSS-M6C62-A Door weatherstrips — Silicone Spray Lubricant XL-6 / ESR-M13P4-A Engine coolant 18.6 quarts (17.6L) Mo[...]

Item Capacity Ford part name Ford part number / Ford specification Power steering fluid Between MIN and MAX on reservoir Motorcraft MERCON 威 VA T F XT -5-QM / MERCON 威 V Engine oil 6.0 quarts (5.7L) Motorcraft SAE 5W20 Premium Synthetic Blend Motor Oil (U.S.) Motorcraft SAE 5W -20 Super Premium Motor Oil (Canada) 3 XO-5W20-QSP (US) CXO-5W20-LSP[...]

Item Capacity Ford part name Ford part number / Ford specification W indshield washer fluid Fill to line on reservoir Motorcraft Premium W indshield W asher Concentrate ZC-32-A / WSB-M8B16-A2 Fuel tank 19.0 gallons (71.9L) —— 1 Use only brake fluids certified to meet Ford specifications. 2 Add the coolant type originally equipped in your vehicl[...]

ENGINE DATA Engine 4.6L SOHC V8 engine 4.6L FFV SOHC V8 engine Cubic inches 281 281 Required fuel 87 octane 87 octane or Ethanol (E-85) Firing order 1-3-7-2-6-5-4-8 1-3-7-2-6-5-4-8 Ignition system Coil on plug Coil on plug Spark plug gap 0.052–0.056 inch (1.32–1.42 mm) 0.041–0.047 inch (1.04–1.20 mm) Compression ratio 9.4:1 9.4:1 Engine dri[...]

IDENTIFYING YOUR VEHICLE Safety Compliance Certification Label The National Highway T raffic Safety Administration Regulations require that a Safety Compliance Certification Label be affixed to a vehicle and prescribe where the Safety Compliance Certification Label may be located. The Safety Compliance Certification Label is located on the structur[...]

The V ehicle Identification Number (VIN) contains the following information: 1. W orld manufacturer identifier 2. Brake system / Gross V ehicle W eight Rating (GVWR) / Restraint System 3. V ehicle line, series, body type 4. Engine type 5. Check digit 6. Model year 7. Assembly plant 8. Production sequence number T RANSMISSION/T RANSAXLE CODE DESIGNA[...]

GENUINE LINCOLN ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Lincoln Accessories are available for your vehicle through your local Lincoln or Ford of Canada dealer . These quality accessories have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and aerodynamic appearance of[...]

For maximum vehicle performance, keep the following information in mind when adding accessories or equipment to your vehicle: • When adding accessories, equipment, passengers and luggage to your vehicle, do not exceed the total weight capacity of the vehicle or of the front or rear axle (GVWR or GA WR as indicated on the Safety Compliance Certifi[...]

A Accessory delay .......................... 44 Air cleaner filter ............... 252–253 Air suspension ...........................174 description .............................. 174 Airbag supplemental restraint system ................110, 119 and child safety seats ............ 112 description ...................... 110, 119 disposal .........[...]

wiper blades ............................ 217 Climate control (see Air conditioning or Heating) ............24 Clock ............................................ 41 Compass, electronic set zone adjustment .................61 Console rear ...................................... 42–43 Controls power seat ................................. 90 steering[...]

Flexible Fuel V ehicle (FFV) ....236 Floor mats ................................... 66 Fluid capacities ......................... 255 Foglamps ..................................... 29 Fuel ............................................ 236 calculating fuel economy ............................57, 243 cap ........................................... 239[...]

programming entry code ......... 79 Keys ....................................... 69, 83 positions of the ignition ......... 164 L Lamps autolamp system ....................... 28 bulb replacement specifications chart .................. 33 daytime running light ...............29 fog lamps ................................... 29 headlamps ............[...]

replacement/additional transmitters ............................... 77 replacing the batteries .............76 Reverse sensing system ........... 178 Roadside assistance .................. 182 S Safety Belt Maintenance ..........104 Safety belts (see Safety restraints) ...................... 95, 98–103 Safety Canopy ........................... 11[...]

T ransmission ............................. 174 brake-shift interlock (BSI) .... 174 fluid, checking and adding (automatic) ............................. 250 fluid, refill capacities .............. 255 lubricant specifications .......... 255 T runk ........................................... 71 remote release ....................67, 74 T urn signal[...]

269[...]

270[...]

271[...]

272[...]