-
Page 1
OWNER'S MANUAL MODEL NUMBER: PP208EPS24 SNOW THROWER Always W ear Eye Protection During Operation IMPORT ANT MANU AL Do Not Throw Away WARNING: Read the Owner's Manual and fol low all W arnings and Safety In struc tions. F ail ure to do so can result in serious injury . 435999 08.11.10 TH Printed in the U.S.A.[...]
-
Page 2
2 IMPORT ANT Safe Operation Practices for W alk-Behind Snow Throwers This snow thrower is capable of amputating hands and feet and throwing objects. F ailure to observe the following safety instructions could result in serious injury . WARNING: This snow thrower is for use on sidewalks, driveways and other ground level surfaces. Caution should be e[...]
-
Page 3
3 6. When cleaning, repairing or inspecting the snow thrower , stop the engine and make certain the collector/impel- ler and all moving parts have stopped. Disconnect the spark plug wire and keep the wire away from the plug to prevent someone from accidentally starting the engine. 7. Do not run the engine indoors, except when starting the engine an[...]
-
Page 4
4 P ARTS P ACKED SEP ARA TEL Y IN CARTON Read these instructions and this manual in its entirety before you attempt to assemble or operate your new snow thrower . Reading the entire manual will familiar- ize you with the unit, which will assist you in assembly , operation and maintenance of the product. Y our new snow thrower has been as sem bled a[...]
-
Page 5
5 AS SEMBL Y / PRE-OPERA TION SPEED CON TROL ROD SPEED CONTROL BRACKET RET AINER SPRING SPEED CONTROL LEVER Fig. 2 SPEED CONTROL ROD HANDLE KNOB L OWER HANDLE PL ASTIC TIE UPPER HANDLE Fig. 1 INST ALL TRACTION DRIVE CONTROL ROD (See Figs. 3 and 4) The traction drive control rod is installed on the snow thrower . 1. Remove plastic tie securing rod t[...]
-
Page 6
6 AS SEMBL Y / PRE-OPERA TION AUGER CONTROL LEVER AUGER CONTROL ROD AUGER CONTROL BRACKET RET AINER SPRING Fig. 6 INST ALL AUGER CONTROL ROD (See Figs. 5 and 6) 1. Retrieve vinyl sleeve and spring from bag of parts and retrieve the auger control rod from carton chute tray . Slide straight rod end through the small hole in the vinyl sleeve. Hook spr[...]
-
Page 7
7 AS SEMBL Y / PRE-OPERA TION CHECK TIRE PRESSURE The tires on your snow thrower were overinflated at the fac- tory for shipping purposes. Correct and equal tire pres sure is important for best snow throwing performance. • Reduce tire pressure to 14-17 PSI. CHUTE DEFLECTOR CONTROL LEVER Fig. 8B Fig. 8A INST ALL CHUTE DEFLECTOR REMOTE CONTROL (See[...]
-
Page 8
8 OPERA TION KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERA TING YOUR SNOW THROWER. Compare the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. These symbols may appear on your snow thrower or in literat[...]
-
Page 9
9 OPERA TION LH and RH turn triggers - used to steer the snow thrower . Drive speed control lever - used to select forward or reverse motion and speed of snow thrower . T raction drive control lever - used to engage power -pro- pelled for ward or reverse motion of snow thrower . Auger control lever - used to engage auger motion (throw snow). Discha[...]
-
Page 10
10 The operation of any snow thrower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your snow thrower or performing any ad just- ments or repairs. We recommend standard safe ty glasses or a wide vision safety mask worn over spectacles. HOW TO USE Y[...]
-
Page 11
11 OPERA TION TO THROW SNOW (See Fig. 13) The auger rotation is controlled by the auger control lever located on the right side handle. • Squeeze auger control lever to handle to engage the auger and throw snow . • Release the auger control lever to stop throwing snow . USING THE CLEAN-OUT TOOL (See Fig. 14) In certain snow conditions, the disc[...]
-
Page 12
12 TO ADJUST SKID PL A TES (See Fig. 17) NOTE: The wrench provided in your parts bag may be used to adjust the skid plates. Skid plates are located on each side of the auger housing and adjust the clearance between the scraper bar and the ground surface. Adjust skid plates evenly to proper height for current surface conditions. For removal of snow [...]
-
Page 13
13 OPERA TION TO ST ART ENGINE • Be sure fuel shut-off valve is in the “OPEN” position. Y our snow thrower engine is equipped with both a 120 V olt A.C. electric starter and a recoil starter . The electric starter is equipped with a three-wire power cord and plug and is designed to operate on 120 V olt A .C. household current. • Be sure you[...]
-
Page 14
14 MAINTENANCE LUBRICA TION CHART GENERAL REC OM MEN DA TIONS The warranty on this snow thrower does not cover items that have been sub ject ed to operator abuse or negligence. T o receive full value from the warranty , operator must maintain snow thrower as in struct ed in this manual. Some ad just ments will need to be made periodically to proper[...]
-
Page 15
15 MAINTENANCE V -BEL TS Check V -belts for deterioration and wear after every 50 hours of operation and replace if necessary . The belts are not ad just able. Replace belts if they begin to slip from wear . (See “TO REMOVE BEL T COVER” in the Service and Adjustments section of this manual). The V -belts on your snow thrower are of special con [...]
-
Page 16
16 SERVICE AND ADJUSTMENTS WARNING: T o avoid serious injury , before performing any service or ad just ments: 1. Be sure the on/off switch is in the OFF position. 2. Remove safety ignition key . 3. Make sure the augers and all mov ing parts have completely stopped. 4. Disconnect spark plug wire from spark plug and place wire where it can not come [...]
-
Page 17
17 SERVICE AND ADJUSTMENTS 8. RELIEVE TENSION ON TRACTION DRIVE BEL T IDLER and remove traction drive belt from around pulleys. HINT : Insert a 3/8" drive ratchet (in the “ON” position) into the square hole in idler arm and rotate ratchet clockwise to relieve tension. 9. With tension relieved on idler , install new traction drive belt arou[...]
-
Page 18
18 SERVICE AND ADJUSTMENTS NOTE: T o seal punctures or prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer . Tire sealant also prevents tire dry rot and cor ro sion. ENGINE See engine manual. CARBURETOR Y our carburetor is not adjustable. Engine performance should not be affected at altitudes up to 7,000[...]
-
Page 19
19 STORAGE Immediately prepare your snow thrower for storage at the end of the season or if the unit will not be used for 30 days or more. WARNING: Never store the snow thrower with gaso line in the tank in side a build ing where fumes may reach an open flame, spark or pilot light as on a fur nace, water heater , clothes dryer or gas ap pli ance. A[...]
-
Page 20
20 TROUBLESHOOTING Does not start 1. Fuel shut-off valve (if so 1. T urn fuel shut-off valve to OPEN position. equipped) in OFF position. 2. Safety ignition key 2. Insert safety ignition key . is not inserted. 3. Out of fuel. 3. Fill fuel tank with fresh, clean gasoline. 4. Throttle in STOP position 4. Move throttle to FAST position (or ON/OFF swit[...]
-
Page 21
21 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO . NO . DESCRIPTION REP AIR P ARTS SNOW THROWER - MODEL NUMBER PP208EPS24 (96198002702) AUGER H[...]
-
Page 22
22 REP AIR P ARTS SNOW THROWER - MODEL NUMBER PP208EPS24 (96198002702) AUGER HOUSING / IMPELLER ASSEMBL Y NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . 10 1[...]
-
Page 23
23 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO . NO . DESCRIPTION REP AIR P ARTS SNOW THROWER - MODEL NUMBER PP208EPS24 (96198002702) AUGER H[...]
-
Page 24
24 KEY P ART NO . NO . DESCRIPTION 1 2 3 3 4 01.11.001-B 4 KEY P ART NO . NO . DESCRIPTION NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . 1 174762X431 SKID P[...]
-
Page 25
25 REP AIR P ARTS SNOW THROWER - MODEL NUMBER PP208EPS24 (96198002702) CONTROL P ANEL / CHUTE KEY P ART NO . NO . DESCRIPTION NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void [...]
-
Page 26
26 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO . NO . DESCRIPTION REP AIR P ARTS SNOW THROWER - MODEL NUMBER PP208EPS24 (96198002702) CONTROL[...]
-
Page 27
27 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO . NO . DESCRIPTION REP AIR P ARTS SNOW THROWER - MODEL NUMBER PP208EPS24 (96198002702) HANDLES[...]
-
Page 28
28 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . REP AIR P ARTS SNOW THROWER - MODEL NUMBER PP208EPS24 (96198002702) HANDLES KEY P ART NO . NO . DESCRIPTION[...]
-
Page 29
29 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO . NO . DESCRIPTION REP AIR P ARTS SNOW THROWER - MODEL NUMBER PP208EPS24 (96198002702) HANDLES[...]
-
Page 30
30 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION REP AIR P ARTS SNOW THROWER - MODEL NUMBER [...]
-
Page 31
31 KEY P ART NO . NO . DESCRIPTION NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . REP AIR P ARTS SNOW THROWER - MODEL NUMBER PP208EPS24 (96198002702) DRIVE 1[...]
-
Page 32
32 REP AIR P ARTS SNOW THROWER - MODEL NUMBER PP208EPS24 (96198002702) DRIVE NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . 9 9 11 11 11 1 2 3 21 5 6 12 13 1[...]
-
Page 33
33 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION REP AIR P ARTS SNOW THROWER - MODEL NUMBER [...]
-
Page 34
34 KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . - - 436266 [...]
-
Page 35
35 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO . NO . DESCRIPTION REP AIR P ARTS SNOW THROWER - MODEL NUMBER PP208EPS24 (96198002702) CHAS SI[...]
-
Page 36
36 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . REP AIR P ARTS SNOW THROWER - MODEL NUMBER PP208EPS24 (96198002702) WHEELS KEY P ART NO . NO . DESCRIPTION [...]
-
Page 37
37 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . REP AIR P ARTS SNOW THROWER - MODEL NUMBER PP208EPS24 (96198002702) WHEELS KEY P ART NO . NO . DESCRIPTION [...]
-
Page 38
38 KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION 01.14.009-A 1 1 422663 SAFETY IGNITION KEY REP AIR P ARTS SNOW THROWER - MODEL NUMBER PP208EPS24 (96198002702) BAG OF P ARTS NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O[...]
-
Page 39
39 KEY P ART NO . NO . DESCRIPTION NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . REP AIR P ARTS SNOW THROWER - MODEL NUMBER PP208EPS24 (96198002702) DECALS [...]
-
Page 40
LIMITED W ARRANTY The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materials and work man ship. For a period of two (2) years from date of purchase by the original consumer pur - chaser , we will repair or replace, at our option, without charge for parts or labor incurred in repl[...]