Heat & Glo LifeStyle SL-750TRS-IPI-D manuale d’uso

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 1 Models: SL-750TRS-IPI-D SL-550TRS-IPI-D SL-350TRS-C Owner ’ s Manual Installation and Operation • Do not store or use gasoline or other flamma- ble vapors and liquids in the vicinity of this or any other appliance. • What to do if you smell gas - Do not try to[...]

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 2 These units MUST use one of the vent systems described in the Installing the Appliance section of the Installers Guide . NO OTHER vent systems or component s MA Y BE USED . This gas appliance and vent assembly MUST be vented directly to the outside and MUST NEVER be[...]

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 3 TABLE OF CONTENTS Safety and Warning Information ......................................................... 2 Service Parts Lists ................................................................................. 4 Section 1: Approvals and Codes ......................[...]

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 4 (NG , LP) Exploded Parts Diagram Service Parts SL-350TRS-C Beginning Manufacturing Date: 4-01 Ending Manufacturing Date: ______ Part number list on following page. 13 6 2 3 4 5 7 Log Set Assembly 12 8 11 10 9 14 15 1[...]

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 5 (NG , LP) Service Parts List IMPORT ANT : THIS IS DA TED INFORMA TION. The most current information is located on your dealers VIP site. When order- ing, supply serial and model numbers to ensure correct service parts. SL-350TRS-C IT E M ST A NDI NG PI LO T SERI A L[...]

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 6 (NG , LP) Exploded Parts Diagram Service Parts Beginning Manufacturing Date: 4-01 Ending Manufacturing Date: ______ SL-350TRS-C IT E M DESCRI PTI O N SERI A L # PAR T N U M B E R 1P i e z o I g n i t o r 291-513 2 B u rn er N eck Gasket 2045-407 3 T h ermost a t Wir[...]

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 7 (NG , LP) Exploded Parts Diagram Service Parts SL-550TRS-IPI-D Beginning Manufacturing Date: 4-04 Ending Manufacturing Date: ______ 7 Log Set Assembly Part number list on following page. 9 8 10 11 12 14 1 15 13 4 5 6 3 2 Î[...]

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 8 (NG , LP) Service Parts List IMPORT ANT : THIS IS DA TED INFORMA TION. The most current information is located on your dealers VIP site. When ordering, supply serial and model numbers to ensure correct service parts. SL-550TRS-IPI-D ITE M DESC RI PT I O N SERI A L #[...]

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 9 (NG , LP) Exploded Parts Diagram Service Parts SL-750TRS-IPI-D Beginning Manufacturing Date: 4-04 Ending Manufacturing Date: ______ Part number list on following page. 9 8 12 11 10 7 Log Set Assembly 14 1 15 13 4 5 6 3 2 Î[...]

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 10 (NG , LP) Service Parts List IMPORT ANT : THIS IS DA TED INFORMA TION. The most current information is located on your dealers VIP site. When order- ing, supply serial and model numbers to ensure correct service parts. SL-750TRS-IPI-D ITE M DESCRI PTI O N SE R IA L[...]

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 11 (NG , LP) Exploded Parts Diagram Service Parts Beginning Manufacturing Date: 4-04 Ending Manufacturing Date: ______ SL-750TRS-IPI-D, SL-550TRS-IPI-D IT E M / PI ÈC E DE SCRI P TI O N SER IA L # / N° DE SÉRIE PAR T N U MB E R / N ° D E P IÈ C E 1 Bu rn er N eck[...]

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 12 1 Approvals and Codes Heat & Glo Quality Systems registered by SGS ICS Appliance Certification The Heat & Glo appliance models discussed in this Installers Guide have been tested to certification standards and listed by the applicable laboratories. Certific[...]

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 13 For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination i[...]

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 14 2 Getting St arted Introducing the Heat & Glo Gas Appliances Heat & Glo direct vent gas appliances are designed to op- erate with all combustion air siphoned from outside of the building and all exhaust gases expelled to the outside. The information contain[...]

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 15 Figure 1. Diagram of the SL-750TRS-IPI-D HOOD GAS CONTROLS GAS LINE ACCESS VENT COLLARS TOP S T ANDOFFS ELECTRICAL ACCESS RA TING PLA TES & LABELS BO TT OM GR IL L E COVER CERA MIC FIBE R P A D 37-7 /8 962 [] 3-9/ 16 90 [] 6-7/8 175 [] 35-5/ 8 905 [] 41 1041.4 [...]

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 16 Figure 2. Diagram of the SL-550TRS-IPI-D 32-9/16 827 [] 3-1 /2 90 [ ] 6- 7/8 174 [] 36 914 [] 31- 1/8 791 [ ] 32-1/8 816 [ ] 5- 1/2 140 [ ] 2-1/ 8 54 [ ] 6 152 [] 35-7/16 900.1 [ ] ø6 - 5 / 8 168.3 [ ] 8- 13/1 6 224 [ ] 16- 1/ 4 413 [ ] 1/2 13 [ ] 15-7/8 403 [ ] 1[...]

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 17 Figure 3. Diagram of the SL-350TRS-C 6-7 / 8 17 4 [] 3-1 / 2 90 [] 30- 5/8 77 7 [] 21-1/4 54 0 [] 29 737 [] 15-1/4 38 8 [] 28 -1/ 8 714 [] 33 836 [] 30 -1/ 2 776 [] 2-1 / 8 55 [] 6 15 3 [] 1/2 13 [] 16 -1/ 4 413 [] 8-3 / 4 22 3 [] 15- 7/ 8 40 2 [] 22- 3/ 4 57 7 [] [...]

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 18 3 Inst alling the Appliance Step 1. Locating the Appliance S pace and clearance requirements for locating a appliance within a room (see Figure 4). Minimum Clearances from the Appliance to Combustible Materials For minimum clearances, see the direct vent terminatio[...]

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 19 Figure 5. Framing Dimensions Framing should be constructed of 2 X 4 lumber or heavier . The framing headers may rest on the appliance stand-offs. Step 2. Framing the Appliance Appliance framing can be built before or after the appliance is set in place. Framing sho[...]

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 20 NOTE: PIPES OVERLAP 1-1/4 INCHES (34.93mm) A T EACH JOINT . Figure 6. DVP-Series Direct V ent Component Specifications (5-inch inner pipe / 8-inch outer pipe) D V P 9 0 S T 12- 9/1 6 11- 1/ 4 7-1/4 1-1/4 T Y P 1/2 TYP 8-9/16 DV P36 DVP48 48 24 36 4 6 DVP4 DVP6 12 D[...]

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 21 NOTE: PIPES OVERLAP 1-3/8 INCHES (34.93mm) A T EACH JOINT . Figure 7 . SL D- Series Direct V ent Component Specifications (4-inch inner pipe / 6 5/8-inch outer pipe) 120” (3048m m) 24” (610mm ) 36” (914mm) 60” (1524mm) 9 1/4 6 5/8 6 1/2 6 3/8 6 1/2 9 5/8 9 [...]

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 22 ! Figure 8. V ent System Component s and T ermination Kits Step 3. Inst alling the V ent System A. V ent System Approvals These models have vent starting collars on both the top and the back of the unit. Depending upon the installation, decide which ONE set of star[...]

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 23 90-DEGR EE EL BOW S Figure 9. Flex V ent The flex vent must be supported with the spacing between support intervals not exceeding 4 feet, with no more than ½ inch sag between supports. A support is required at each change in venting direction, and in any location [...]

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 24 V H 1' MIN. (305mm) 2' MAX. (610mm) 2' MIN. (610mm) 4' MAX. (1.22m) 3' MIN. (914mm) 6' MAX. (1.86m) 4' MIN. (1.22m) 8' MAX. (2.4m) V+H=40' MAX. (12.4m) H = 8' MAX. (2.4m) Figure 12. V enting with One 90° Elbow Figu[...]

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 25 V H H + H 1 1' MIN. (305 mm) 2' MAX. (610 mm) 4' MAX. (1.22m) 2' MIN. (610 mm) 4' MAX. (1.22 m) 8' MAX. (2.4m) 3' MIN. (914 mm) 6' MAX. (1.86 m) 12' MAX. (3.6m) 4' MIN. (1.22 m) 8' MAX. (2.48 m) 16' MAX. ([...]

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 26 Figure 15. V enting with T wo 90° Elbows Use SL D-Series component s only . VENTING WITH TWO (2) 90 o ELBOWS NA TURAL GAS H + H 1 MAX. = 16 FT (4.8m) V + H + H 1 MAX. = 40 FT (12.2m) MODELS: SL-550TRS-D , SL-750TRS-D H + H 1 (MAX.) 2 FT (610mm) 3 FT (914mm) 4 FT ([...]

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 27 Figure 16. Venting with T wo 90° Elbows Use SL D-Series components only . H V V 1 VENTING WITH TWO (2) 90 o ELBOWS NA TURAL GAS H MAX. = 16 FT (4.8m) V + V 1 + H MAX. = 40 FT (12.2m) MODELS: SL-550TRS-D, SL-750TRS-D H (MAX.) 2 FT (610mm) 3 FT (914mm) 4 FT (1.22m) [...]

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 28 Figure 17. V enting with Three 90° elbows 1' MIN. (305 mm) 2' MAX. (610mm) 4' MAX. (1.22m) 2' MIN. (610 mm) 4' MAX. (1.22m) 8' MAX. (2.48m) 3' MIN. (914 mm) 6' MAX. (1.86m) 12' MAX. (3.72m) 4' MIN. (1.22 m) 8'[...]

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 29 Figure 18. V enting with three 90° elbows Use SL D-Series components only . VENTING WITH THREE (3) 90 o ELBOWS NA TURAL GAS VENTING WITH THREE (3) 90 o ELBOWS PROP ANE V + H + V 1 + H 1 MAX. = 40 FT (12.2m) V + H + V 1 + H 1 MAX. = 40 FT (12.2m) MODEL: SL-350TRS-C[...]

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 30 Use SL D-Series components only . Figure 19. V enting with three 90° elbows V 1 H 1 H V VENTING WITH THREE (3) 90 o ELBOWS NA TURAL GAS H + H 1 MAX. = 16 FT (4.8m) V + V 1 + H + H 1 MAX. = 40 FT (12.2m) MODEL SL-750TRS-D H + H 1 (MAX.) 2 FT (610mm) 3 FT (914mm) 4 [...]

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 31 Figure 20. V enting with Four 90° elbows VENTING WITH FOUR (4) 90° ELBOWS NA TURAL AND PROP ANE GAS V (MIN.) H (MAX.) 2' (609mm) 5' (1.52m) V 1 (MIN.) H 1 (MAX.) V 2 (MIN.) 5' (1.52m) 5' (1.52m) 4.5' (1.37m) V + V 1 + V 2 + H + H 1 MAX. =[...]

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 32 ! Figure 21. Insert screwdriver or similar object here to remove cap. CUT HERE V enting Out Rear V enting Out T op ! WARNING: THE REAR VENT COLLAR SEAL CAP MUST REMAIN A T T ACHED T O THE REAR VENT COLLARS IF THE VENT SYSTEM IS A TT ACHED TO THE T OP ST ARTING COLL[...]

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 33 For V ertical Runs - The vent system must be supported every eight (8) feet (2.4m) above the appliance flue outlet by wall bracket s. T o inst all support brackets for vertical runs: • Attach wall brackets to the vent pipe and secure the wall bracket to the frami[...]

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 34 For V ertical Runs - One ceiling firestop is REQUIRED at the hole in each ceiling through which the vent passes. T o install firestop s for vertical runs that pass through ceilings: • Position a plumb bob directly over the center of the verti- cal vent component.[...]

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 35 C. V ent T ermination SL-Series V enting Only: For Horizont al T erminations - T o attach and secure the termination to the last section of horizontal vent: • Rotate and interlock the ends as described at the begin- ning of the Installing V ent Components section[...]

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 36 V = VENT TERMINAL X = AIR SUPPL Y INLET = AREA WHERE TERMINAL IS NOT PERMITTED Figure 30. V ent T ermination Minimum Clearances A = 1 2" ....................... clearances above grade, veran- da, porch, deck or balcony B = 1 2" ....................... cle[...]

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 37 For V ertical T erminations - T o locate the vent and install the vent sections: • Locate and mark the vent centerpoint on the underside of the roof, and drive a nail through the centerpoint. • Make the outline of the roof hole around the centerpoint nail. • [...]

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 38 Step 4. Positioning, Leveling, and Securing the Appliance • Place the appliance into position. • Level the appliance from side to side and from front to back. • Shim the appliance with non-combustible material, such as sheet metal, as necessary . • Secure t[...]

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 39 • Insert insulation from the outside of the appliance and pack the insulation tightly to totally seal between the pipe and the outer casing. • At the gas line access hole the gap between the supply piping and gas access hole can be plugged with non- combustible[...]

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 40 Step 8. W iring the Appliance NOTE: Electrical wiring must be installed by a licensed electrician. CAUTION: DISCONNECT REMOTE CONTROLS IF AB- SENT FOR EXTENDED TIME PERIODS. THIS WILL PRE- VENT ACCIDENT AL APPLIANCE OPERA TION. Figure 35. Standing Pilot Ignition Wi[...]

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 41 Figure 36. Intermittent Pilot Ignition (IPI) Wiring Diagram TRANSFORMER 3 V AC PLUG IN R E D BA T TER Y P ACK THE RM OSTA T WIRE ASSEMBL Y JUMPER WIRE (TO BROWN) ORANGE GRE EN VA LV E GROUND TO FIREPLACE CHASSI S WHIT E ORANGE IGNITION MODULE 3 V AC INTE RMITTENT P[...]

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 42 Step 9. Finishing Figure 38 shows the minimum vertical and corresponding maximum horizontal dimensions of appliance mantels or other combustible projections above the top front edge of the appliance. See Figures 4 and 5 for other appliance clearances. Only non-comb[...]

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 43 Inst alling the T rim Combustible materials may be brought up to the specified clearances on the side and top front edges of the appliance, but MUST NEVER overlap onto the front face. The joints between the finished wall and the appliance top and sides can only be [...]

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 44 Step 1 1. Before Lighting the Appliance Before lighting the appliance, be sure to do the following: Remove all paperwork from underneath the appliance. Review safety warnings and cautions • Read the Safety and Warning Information section at the beginning of this [...]

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 45 4 Maint aining and Servicing Y our Appliance Appliance Maintenance Although the frequency of your appliance servicing and main- tenance will depend on use and the type of installation, you should have a qualified service technician perform an appli- ance check-up a[...]