Go to page of
Similar user manuals
-
Home Gym
Stamina Products 35-1699
26 pages 3.92 mb -
Home Gym
Stamina Products 15-0100
15 pages 0.47 mb -
Home Gym
Stamina Products Premier 690
19 pages 0.46 mb -
Home Gym
Stamina Products 50lb
2 pages 0.17 mb -
Home Gym
Stamina Products 55-2010
23 pages 0.83 mb -
Home Gym
Stamina Products 15 - 0120A
4 pages 0.13 mb -
Home Gym
Stamina Products LT-2000
36 pages 3.11 mb -
Home Gym
Stamina Products 65-1380
18 pages 3.02 mb
A good user manual
The rules should oblige the seller to give the purchaser an operating instrucion of Stamina Products VG1500, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.
What is an instruction?
The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Stamina Products VG1500 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.
Unfortunately, only a few customers devote their time to read an instruction of Stamina Products VG1500. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.
What should a perfect user manual contain?
First and foremost, an user manual of Stamina Products VG1500 should contain:
- informations concerning technical data of Stamina Products VG1500
- name of the manufacturer and a year of construction of the Stamina Products VG1500 item
- rules of operation, control and maintenance of the Stamina Products VG1500 item
- safety signs and mark certificates which confirm compatibility with appropriate standards
Why don't we read the manuals?
Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Stamina Products VG1500 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Stamina Products VG1500, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Stamina Products service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Stamina Products VG1500.
Why one should read the manuals?
It is mostly in the manuals where we will find the details concerning construction and possibility of the Stamina Products VG1500 item, and its use of respective accessory, as well as information concerning all the functions and facilities.
After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.
Table of contents for the manual
-
Page 1
50-3000 ST AMINA PRODUCTS MADE IN CHINA Product May V ary Slightly From Pictured. 2007, 10 Exercise ca n present a health risk. Con sult a physicia n bef ore beginning a ny exercise progra m with this equipment. If you feel faint or dizzy , i mmedi ately discontinue use of this equi pment. Serious bodily injury ca n occur if this equi pment is not [...]
-
Page 2
T ABLE OF CONTENTS 2 W arm-up a nd Cool-Down 16 W arra nty 17 Product Parts Drawing 18 Parts List 19 Note s 21 Fax/Mail Ordering Form 22 Page Page Safety In struction s 2 Before Y ou Begin 4 Hardware Identification Chart 5 Asse mbly In structions 6 Setting up The Acce ssories 14 Storage 15 M aintena nce 15 W ARNING: Bef ore starting a ny exercise o[...]
-
Page 3
THAN K YOU FOR PURCHASING THE VIPER V G1500 TM Leverage Syste m 3 Should you have a ny question s, ple a se call our Customer Service De partment toll-free number , 1 (800) 375-7520 Monday - Thursday , 7:30 A.M. - 5:00 P .M. Central T ime. Friday , 8:00 A.M. - 3:00 P .M., Central Ti me. TELEPHONE CUSTOMER SER VICE T el: 1 (800) 375-7520 FA X CUSTOM[...]
-
Page 4
4 Lat Bar Ca ble Ba ck Cushion Foa m Roller Leg Lift Left Ha ndlebar Lever Arm Foa m Roller Ankle Cuff Ba se Fra me Se at Cushion Upright Long Chain THE FOLLOWING TOOLS ARE REQUIRED FOR ASSEMBL Y : Straight Bar Ha ndle Left Leverage Arm Lower Upright BEFORE YOU BEGIN Tha nk you for choosing the V G1500 TM Leverage Syste m. W e ta ke great pride in [...]
-
Page 5
5 Part No. and De scription Qty HAR D W ARE IDENTIFICA TION CHAR T This chart is provided to help identify the hardware used in the a ssembly process. Pla ce the wa shers, the end of the bolts, or screws on the circles to che ck for the corre ct di a meter . Use the small scale to check the length of the bolts a nd screws. NOTICE: The length of all[...]
-
Page 6
ASSEMBL Y INSTRUCTIONS 6 Pla ce all parts from the box in a cleared area a nd position them on the floor in front of you. Re move all pa cking materials from your are a and pla ce the m ba ck into the box. Do not dispose of the pa cking materials until a ssembly is completed. Read e a ch step carefully before beginning. If you are missing a part pl[...]
-
Page 7
ASSEMBL Y INSTRUCTIONS 7 STEP 3 Atta ch the LOWER UPRIGHT(6) to the BASE FRAME(1) with the SUPPORT BRACKET(5), HEX BOL TS (M12x1.75x70mm)(72), W ASHERS(M12)(80), and NYLOCK NUTS(M12x1.75)(82). Do not tighten the bolts. Atta ch the LOW UPRIGHT(6) to the REAR ST ABILIZER(2) with HEX BOL TS(M12x1.75x70mm)(72), W ASHERS(M12)(80), a nd NYLOCK NUTS(M12x1[...]
-
Page 8
ASSEMBL Y INSTRUCTIONS 8 STEP 6: Run the SMALL BALL END of the CABLE(45) through the slot at the top end of the UPRIGHT(7). Atta ch the CABLE(45) to the UPRIGHT(7) at "A" with the LAR GE PULLEY(44), a HEX BOL T (M10x1.5x95mm)(70), two W ASHERS(M10)(81), a nd a NYLOCK NUT(M10x1.5)(83). Run the CABLE(45) through the pulley bra cket on the U[...]
-
Page 9
ASSEMBL Y INSTRUCTIONS 9 STEP 9 Refer to the inset drawing. Atta ch the SLIDER SUPPORT(14) to the LOWER UPRIGHT(6) with HEX BOL T (M12x1.75x160mm)(77), W ASHERS(M12)(80), a nd NYLOCK NUT(M12x1.75)(82). Do not over tighten the bolt, a s the SLIDER SUPPORT(14) must be able to pivot smoothly . STEP 10 Pull the SPRING PIN(34) on the SLIDER SUPPORT(14) [...]
-
Page 10
ASSEMBL Y INSTRUCTIONS 10 STEP 12 Atta ch the SEA T FRAME(9) to the LOWER UPRIGHT(6) with HEX BOL TS(M12x1.75x100mm)(75), W ASHERS(M12)(80), a nd NYLOCK NUTS(M12x1.75)(82). STEP 13 Atta ch the LEG LIFT(10) to the SEA T FRAME(9) with HEX BOL T(M12x1.75x90mm)(74), W ASHERS (M12)(80), an d NYLOCK NUT(M12x1.75)(82). STEP 14 Run the CABLE(45) through th[...]
-
Page 11
ASSEMBL Y INSTRUCTIONS 11 STEP 16 Atta ch the FOAM SUPPORTS(15) to both sides of the LOWER UPRIGHT(6) with HEX BOL TS (M12x1.75x100mm)(75), W ASHERS(M12)(80), a nd NYLOCK NUTS(M12x1.75)(82). STEP 17 Atta ch the HEAD REST(35) and BACK CUSHION(36) to the BACK SUPPORT(12) with HEX BOL TS (M10x1.5x25mm)(67) a nd W ASHERS(M10)(81). STEP 18 Atta ch the S[...]
-
Page 12
ASSEMBL Y INSTRUCTIONS STEP 19: There is a n "L" decal on the LEFT LEVERAGE ARM(17), a nd a n "R" decal on the RIGHT LEVERAGE ARM(18). Slide the RIGHT LEVERAGE ARM(18) onto the shaft at right side of the ARM BRACE(16) a nd secure with LARGE W ASHER(M12xø 31mm)(79) a nd NYLOCK NUT(M12x1.75)(82). 12 R R L L Slot Screw hole FRONT [...]
-
Page 13
ASSEMBL Y INSTRUCTIONS STEP 22 Slide a FOAM ROLLER(39) onto a SUPPORT TUBE(38) a nd screw a SECURING CAP(41) onto the end of the SUPPORT TUBE(38). Insert the other end of the SUPPORT TUBE(38) through the hole in the LEG LIFT(10). Slide a nother FOAM ROLLER(39) over the protruding end of the SUPPORT TUBE(38) and screw a SECURING CAP(41) onto the end[...]
-
Page 14
SETTING UP THE ACCESSORIES 14 STRAIGHT BAR HANDLE(51), ANKLE CUFF(53) The STRAIGHT BAR HANDLE(51) a nd ANKLE CUFF(53) ca n be atta ched to the ball end of the CABLE(45) at the bottom of the LEG LIFT(10) with two QUICK LINKS(47) a nd one of the CHAINS(55, 56). LA T BAR(49) Atta ch the LA T BAR(49) to the CABLE(45) with a QUICK LINK(47). For some exe[...]
-
Page 15
15 MAINTENANCE The safety a nd integrity designed into the V G1500 TM Leverage System ca n only be maintained when the V G1500 TM Leverage Syste m is regularly exa mined f or da mage a nd wear . Speci al attention should be given to the following: V erify that the warning a nd notice labels are in pla ce a nd ea sy to rea d. Call Sta mina Products [...]
-
Page 16
16 W ARM-UP a nd COOL-DOW N W arm-up The purpose of warming up is to pre pare your body for exercise a nd to mini mize injuries. W arm up for two to f ive minutes bef ore strength-training or aerobic exercising. Perform a ctivities that raise your heart rate a nd warm the working muscles. Activities may include brisk wal king, jogging, jumping ja c[...]
-
Page 17
17 W ARRANTY LIMITED W ARRANTY MODEL 50-3000 Sta mina Products, Inc. warra nts that this product will be free from defects in materi als a nd workma nshi p under normal use, service a nd proper operation f or a period of 90 days on the parts a nd three years on the fra me from the date of the original purcha se from a n authorized retailer . THIS W[...]
-
Page 18
PRODUCT P ARTS DR A WING 18 FRONT BACK[...]
-
Page 19
P ARTS LIST DIAGRAM# P ART NAME QTY 1 Ba se Fra me 1 2 Rear Sta bilizer 1 3 Rear Support 1 4 Foot Plate 1 5 Support Bra cket 1 6 Lower Upright 1 7 Upright 1 8 Lever Arm 1 9 Seat Fra me 1 10 Leg Lift 1 1 1 Seat Post 1 12 Ba ck Support 1 13 Adjustment bar 1 14 Slider Support 1 15 Foa m Support 2 16 Arm Bra ce 1 17 Left Leverage Arm 1 18 Right Leverag[...]
-
Page 20
20 P ARTS LIST DIAGRAM# P ART NAME QTY 48 Hook Sleeve 2 49 Lat Bar 1 50 Foa m Gri p 2 51 Straight Bar Ha ndle 1 52 Ha nd Grip 2 53 Ankle Cuf f 1 54 Ab Curl Stra p 1 55 Long Chain (10 Links) 1 56 Short Chain (6 Links) 1 57 Sta nd 2 58 Bumper 2 59 Recta ngular Plug (30mm x 60mm) 3 60 Recta ngular Plug (50mm x 75mm) 1 61 Square Plug (50mm x 50mm) 10 6[...]
-
Page 21
21 NOTES[...]
-
Page 22
IMPORT ANT : Before filling out the form below ma ke sure you have the right information. Refer to the parts list to make sure you're ordering the right parts! Detach a nd M ail or Fax the Form Below Sta mina Products, Inc. P .O. Box 1071 Springfield, MO 65801-1071 IMPORT ANT : We must have your phone number in order to proce ss the order! F A[...]