Glancetron GT15wide manual

T ouch Screen LCD Monitors USER’ s GUIDE Rev .A Glancetron GT15-W ide www .glancetron.com[...]

The information contained in this document is subject to change without notice. This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this document may be reproduced,translated to another language or stored in a retrieval system, or transmitted by any means, electronic, mechanical, photoc[...]

T able of Contents Usage Notice Precautions............................................................................................................................. 1 Introduction About Glancetron GT -15Wide ................................................................................................ 2 T ouch Screen for Glancetron GT -15Wide[...]

1 Usage Notice ! W arnin g - T o prevent the risk o f fi re or shock hazards, do not expose this product to rain or moisture. ! W arnin g - Please do not open or disassemble the product as this ma y cause e l ec tri c s h oc k. Precautions Follow all warnings, precautions and maintenance as recommended in this user ’s manual to maximize the life[...]

Introduction About Glancetron GT -15Wide The Glancetron GT -15Wide is a 39.6cm (15.6”) fl at panel screen with an active matrix, thin- fi lm transistor (TFT) liquid crystal display (LCD). Features include: • Direct analog signal input • Active matrix TFT LCD technology • 1366 x 768 WXGA resolution • 39.6cm (15.6") viewable display [...]

Package Overview 3 LCD Display Power Cord VGA Signal Cable RS-232 Cable USB Cable ( A to B) Quick Start Guide DC Power Supply T ouch Driver CD Screw Audio-in Cable[...]

Installation Product Overview • Front V iew • Bottom V iew (Without Stand) POWER SWITCH DC IN VGA RS-232 USB EARPHONE AUDIO 4[...]

Kensington Security Slot The monitor can be secured to your desk or any other fi xed object with Kensington lock security products. The Kensington lock is not included. 5[...]

VESA Mount Y our Monitor This monitor conforms to the VESA Flat Panel Physical Mounting Interface standard which de fi nes a physical mounting interface for fl at panel monitors, and corresponding with the standards of fl at panel monitor mounting devices, such as wall and table arms. The VESA mounting interface is located on the back of your mo[...]

7 Start Y our Installation Please follow these instructions so that you can hookup the cables to associated connector . 1. Lay the LCD fl at on an even surface. 2. Move the stand into position as seen in the step 2 diagram. 3. Remove the cable cover as seen in the step 3 diagram. 4. Connect the cables to the appropriate connectors as seen in the s[...]

Remove the Deskstand Remove 4 screws and then remove hinge. 8[...]

Connecting the Display (Figure 10.1) T o setup this display , please refer to the following fi gure and procedures. 1. Be sure all equipment is turned off. 2. Connect the DC adapter to the power connector on the monitor and the other end into an electrical outlet (10.1). 3. Connect the D-SUB cable from the display's VGA input connector to the[...]

(Figure 10.1) 10[...]

User Controls Front Panel Controls Icon key Name Menu Up Down Enter Power OSD Key Menu off status Menu on status Menu appear Menu disappear / return to main item Brightness Main item select up / Adjust up Mute Main item select down / Adjust down Enter / Select sub-item function Power On / Off 11[...]

12 How to Use the OSD Menus Icon key Name Menu Up Down Enter Power 1. Press the “MENU” button to pop up the “on-screen menu” and press “Up” or “Down” button to select among the six functions in the main menus. 2. Choose the adjustment items by pressing the “Enter ” button. 3. Adjust the value of the adjustment items by pressing [...]

On-Screen Display Menus Main OSD Menu: ITEM CONTENT Contrast The monitor luminance level control. Brightness The monitor backlight level control. Auto Adjust Fine-tune the image to full screen automatically . Left/Right Moving screen image horizontal position to left or right. Up/Down Moving screen image vertical position to up or down. Horizontal [...]

Appendix T roubleshooting If you are experiencing trouble with the LCD display , refer to the following. If the problem persists, please contact your local dealer or our service center . Problem: No image appears on screen. ► Check that all the I/O and power connectors are correctly and well connected described in the "Installation" sec[...]

W arning Signal If you see warning messages on your LCD screen, this means that the LCD display cannot receive a clean signal from the computer graphics card. There may be three sources for this problem. Please check the cable connections or contact your local dealer or our service center for more information. No Signal This message means that the [...]

Product Dimensions 388.23 272.13 214.81 214.17 237.51 58.07 65.57 Front View Side View T op View 16[...]

Compatibility Modes Mode Resolution H-Frequency (KHz) V -Frequency (Hz) IBM VGA 720X400 31.47 70 IBM VGA 640X480 31.47 60 Apple Mac 640X480 35.00 66 VESA VGA 640X480 37.86 72 VESA VGA 640X480 37.50 75 VESA VGA 800X600 35.16 56 VESA VGA 800X600 37.88 60 VESA VGA 800X600 48.08 72 VESA VGA 800X600 46.88 75 Apple Mac 832X624 49.72 75 VESA XGA 1024X768 [...]

T ouch Screen Driver Installation The Glancetron GT -15Wide is available with both RS232 and USB connections. The touch driver is located on the enclosed CD-ROM for these operating systems: Windows ® 7, VIST A 64/32 bits, XP , 2000, ME, 98, NT4.0, CE, XP Embedded, Linux, Apple ® Mac OS. Please Note: The Glancetron GT -15Wide is Microsoft ® Windo[...]

19 Glancetron GT -15Wide Install Instructions: If you are using a PC running Windows ® 7, VIST A, XP , 2000, ME, 98, NT4.0, follow the instructions below: 1. Power on the PC. 2. Be sure the USB or the RS-232 Serial cable is connected from the PC to the LCD display . 3. Open the CD-ROM. 4. Follow the step-by-step instructions as shown on the pop-up[...]

If you are using a PC running Windows ® CE, follow the instructions below: 1. Power on the computer . 2. Make sure that the RS232 or USB cable is connected to the computer . 3. Using Platform Builder , build an image fi le by following the step-by-step instructions found in the folder on the CD-ROM. If you are using a PC running Linux or Apple ®[...]