Harman Stove Company 929BV manual

SAFETY NOTICE PLEASE READ THIS ENTIRE MANUAL BEFORE YOU INST ALL AND USE YOUR NEW ROOM HEA TER. F AILURE TO FOLLOW INSTRUCTIONS MA Y RESUL T IN PROPERTY DAMAGE, BODIL Y INJUR Y , OR EVEN DEA TH. IF THIS HARMAN STOVE IS NOT PROPERL Y INST ALLED, A HOUSE FIRE MA Y RESUL T . FOR YOUR SAFETY , FOL- LOW INST ALLA TION DIRECTIONS. CONT ACT LOCAL BUILDING[...]

2 INTRODUCTION ........................................................... 3 INST ALLA TION ............................................................. 4 Clearances ................................................................. 4 V enting ....................................................................... 5 T est for Flue Spillage ........[...]

3 Introduction The Harman Clarity 929BV V ented Gas Heater is a listed gas-red vented room heater tested by Intertek T esting/W arnock Hersey to ANSI standard Z21.88- 2002, CSA 2.33-M02, and CAN/CGA-2.17-M91. The installation of the Clarity V ented Gas Heater must conform with local codes, or in the absence of local codes, with the current editi[...]

4 In addition to these clearances, adequate accessibil- ity clearance for servicing and proper operation must be maintained. Do not in any way obstruct the combustion air inlets that are located under the heater . If this appliance is installed directly on carpeting, tile or other combustible material other than wood ooring the appliance shall b[...]

5 VENTING Use Only Appr oved V enting The Clarity gas heater is tested and listed for connection to a 4" (100 mm) listed Class B venting system. If the uni t is i ns tal le d to vent thr oug h an appro ve d maso nr y chimney or a factory-built chimney system, an approved Class B chimney liner must be used. Observe local codes when venting the [...]

6 The front is released when levers on the left and right sides are pushed to the rear ASSEMBL Y The Clarity is shipped from the factory with the log set packed inside the rebox. T o prepare the stove for installa - tion, the log set must be unpacked, the appropriate burner system module for either natural gas or propane installed, and the logs [...]

7 Install the Back Log and Back Brick Panel These two components are installed as a single piece. Rest the back brick panel on the shelf located on the back side of the back log, and center it. Holding the two pieces as a single unit, tilt the top forward slightly and manuever it over the top of the rear burner—taking care that the top corners cl[...]

8 Pipe Length Schedule 40 Pipe T ubing, T ype L (Feet) Inside Diameter Outside Diameter RECOMMENDED GAS PIPE DIAMETER NOTE: NEVER USE PLASTIC PIPE. CHECK T O CONFIRM WHETHER YOUR LOCAL CODES ALLOW COPPER TUBING OR GAL V ANIZED PIPE. N.G. L.P . N.G. L.P . 0-10 1/2" 3/8" 1/2" 3/8" 1.3 cm 1.0 cm 1.3 cm 1.0 cm 10-40 1/2" 1/2&qu[...]

9 W ARNING: THIS HEA TER IS EQUIPPED WITH A THREE-PRONGED GROUNDING PLUG THA T SHOULD BE PLUGGED DIRECTL Y INTO A PROP - ERL Y GROUNDED RECEPT ACLE. DO NOT CUT OR R EMO VE TH E GR OU ND IN G PR ONG FRO M THE PLUG. T erminal strip for thermostat connec- tion Rear view of Clarity CONNECTING THE CORDSET The Clarity B-V ent Gas Heater must be installed[...]

10 MONITORING THE GAS FLAME Periodically , the ames of the Clarity B-V ent Gas Heater should be checked while it is operation. The ames should be relatively well-dened and stable. They should be bright yellow with a blue base where attached to the burner ports. The ames should not look orange or sooty . Portions of the logs will glow re[...]

1 1 •If the knob does not pop up when released, stop and immediately call your service technician or gas supplier . •If the pilot will not stay lit after several tries, turn the gas control knob to "OFF" and call your service technician or gas supplier . 1 1. Turn the gas control knob counterclockwise to "ON." 12. Pl ace the[...]

12 Maintenance A qualied service person recommended by your Harman dealer should conduct an annual inspection and maintenance of your Clarity , its venting, and the installa - tion to keep it running safely and efciently . These pro - cedures should be performed only by a qualied service person. The gas supply should be turned of f wheneve[...]

13 The Clarity B-V ent gas heater , when installed, must be electri - cal ly gro un ded i n a cco rd anc e with local co des o r , in th e absen ce of local codes, with the current edition of the National Electri - cal Code, ANSI/NFP A 70 in the United States or the curr ent Canadian Electrical Code CSA 22.1 in Canada.[...]

14 Parts List The following replacement parts for your Harman Clarity B-V ent are available from your Harman dealer . ID# Part No. Part 1 1-89-08270 BVG weldment 2 1-10-08262-1 Left wing door 3 1-10-08262-2 Right wing door 4 3-40-08286 1/2" gas inlet ex 5 3-40-08235 Rear log 6 3-40-08236 Front log 7 3-40-08237 T op log 8 3-40-08401 Ember st[...]

15 Clarity B-V ent - Exploded V iew[...]

16 40 38 49 37 12 14 13 52 41 44 48 42 43 31 32 33 50 51 Clarity Burner Module - Exploded V iew[...]

17 Appendix A CONVER TING THE CLARITY B-VENT FROM ONE GAS T O ANOTHER IN THE FIELD NOTE: THE CONVERSION SHALL BE CAR- R I E D O U T I N A C C O R D A N C E W I T H T H E R E - QUIREMENTS OF THE PROVINCIAL OR LOCAL AUT HORI TIE S HA VING JUR ISD IC TION A ND IN ACCORDANCE WITH REQUIREMENTS OF THE CUR RE NT ED IT IO N OF THE NA TION AL FUE L GAS CODE[...]

18 Appendix B DE-RA TING FOR HIGH AL TITUDE For U.S. installations, the Clarity B-V ent is approved for elevations up to 2000 feet using the factory-installed burner injec tors. At elevations abov e 2000 fee t, U.S. codes req ui re a d ecr ea se in the input ratin g by c ha ngi ng t he burn er injectors to a smaller size. The chart below lists by p[...]

19 Clarity B V ent Gas Heater Specications T ested to ANSI Z21.88-2002, CSA 2.33-M02, CAN/CGA 2.17-M91. NA TURAL GAS PROP ANE Input Rating (Btu/hr) (0-1375 m) 40,000 40,000 Min. Input Rating (Btu/hr) (0-1375 m) 27,000 28,000 Injector Sizes (DMS) (front/center/rear (0-1375 m) 47/56/39 56/71/53 Manifold Pressure (in w .c./kPa) 3.5/0.87 10.0/2.49 M[...]

20 Harman Stove Company warrants its products to be free from defects in material or workmanship, in normal use and ser - vice, for a period of 6 years from the date of sales invoice and for mechanical and electrical failures, in normal use and service, for a period of 3 years from the date of sales invoice. If defective in material or workmanship,[...]