Keys Fitness Triumph 7.3t manual

Owner’ s Manual T riumph 7.3t T r eadmill Customer Ser vice 1.888.340.0482 K eys Fitness Products 4009 Distribution Drive Suite 250 Garland, TX 75041 www .keysfitness.com 415-00007 04/05 Rev D Model Name : 7.3t Serial Number : Purchase Date : Write down for future reference Serial Number Decal Location[...]

Important Safety Information 3 Before Y ou S tart 4 Assembly 5-9 W arm Up Exercises 10 Moving Instructions 1 1 Power Requirements 12 Console Panel Functions 13 Program and Operation 14-15 Program Profiles 16 Belt Adjustment 17 Change to MPH or KPH 18 Maintenance Instructions 19 T roubleshooting Guide 20 Error Messages 21 Calibration Sequence 22 Par[...]

Impor tant Safety Inf or ma tion W ARNING! Before using this treadmill or starting any exercise program, consult your physician. This is espe- cially important for persons over the age of 35 and/or persons with pre-existing health problems. The man- ufacturer or distributor assumes no responsibility for personal injury or property damage sustained [...]

Bef ore Y ou Star t Thank you for purchasing the T riumph 7.3t T readmill! This quality product you have chosen was designed to meet your needs for cardiovascular exercise. Before you start, please read the Owner's Manual and become familiar with the operation of your new treadmill. Remember to take the time to perform the str etching exercise[...]

Assembl y The T riumph 7.3t T readmill will require assembly before operating. After opening the box, remove any packing material from the treadmill. Do not throw away any packing materials until the unit is working pr operly . Place the base on a clean, level surface. Make sure the electrical cord will easily reach an electrical outlet. Locate the[...]

Assembl y Assembly requires the included allen wrench and phillips screwdriver . Do not plug in the power cord until all assembly steps ar e completed. 6 Figure 1: Console Harness Location Figure 2: Console Harness Connection 1. W ith the treadmill deck in the down position, leave the unit on the original packing material to assemble all parts. Cau[...]

Assembl y 7 Figure 3: Left and Right Upright Installation Figure 4: Console Installation 4. Install the Left and Right Uprights to the tread- mill base frame by inserting the upright connect- ing bracket into base frame as seen in Figure 3, using Allen Bolt 5/16”-18 x 70 (Qty . 4), Spring W asher 8 mm (Qty . 4), and W asher 9*16*1.6 mm (Qty . 4).[...]

Assembl y 8 7. Position the Left and Right Bottom Handle Covers to underside of handle assembly , then connect the EKG Harness W ires to the Left and Right Bottom Handle Pulse Plates as shown in Figure 5. T ighten into place using Phillip Screw ST4.2X16 (Qty . 6). Next, install the End Caps to the handle assem- bly . IMPOR T ANT , PLEASE NOTE: T ig[...]

Assembl y 9 9. Install the Left and Right Fender to Base using Philip Screw ST4.2X16 as shown in Figure 7. 10. Install the Long Bumper (Qty 2) to Base using Allen Bolt M8*30 (Qty . 2) as shown in fig- ure 8. Figure 7: Left and Right Fender Installation Figure 8: Long Bumper Installation BASE BASE LEFT FENDER PHILIP SCREW ST4.2x16 RIGHT FENDER ALLEN[...]

W ar m Up Exercises T OE T OUCH STRETCH Stand, bending your knees slightly and slowly bend forward from your hips. Allow your back and shoulders to relax as you reach down toward your toes as far as possible. Hold for 15 counts, then relax. This will stretch your ham- strings, back of knees, and back. HAMSTRING STRETCH Sit with one leg extended. Br[...]

Mo ving Instr uctions CAUTION! T O A VOID THE RISK OF INJUR Y , NEVER A TTEMPT TO MOVE THE TREADMILL WHILE IT IS IN THE UNFOLDED OPERA TING POSITION. T O REDUCE THE POSSIBILITY OF INJUR Y WHILE LIFTING , BEND YOUR LEGS AND KEEP YOUR BACK STRAIGHT . AS YOU RAISE THE TREADMILL, LIFT USING YOUR LEGS, NOT YOUR BACK. IN ORDER TO RAISE OR LOWER THE TREAD[...]

P ow er Requirements I MPROPER CONNECTION OF THE EQUIPMENT GROUNDING CONNECTOR CAN RESUL T IN A RISK OF AN ELECTRIC SHOCK. CHECK WITH A QUALIFIED ELECTRICIAN OR SER VICE MAN IF YOU ARE IN DOUBT AS T O WHETHER THE PRODUCT IS PROPERL Y GROUNDED. DO NOT MODIFY THE PLUG PROVIDED WITH THE PRODUCT . IF PLUG WILL NOT FIT THE OUTLET , HA VE A PROPER OUTLET[...]

Console P anel Functions There are five display windows on the control panel to provide feedback information. TIME / P ACE WINDOW TIME: Indicates elapsed time after pressing start in minutes and seconds (0-99 minutes, 0-59 seconds) P ACE: Indicates countdown in seconds to the next interval starting at 5 seconds and counting to 0 seconds. SPEED WIND[...]

QUICK ST AR T / MANUAL MODE 1. Plug into a surge protector outlet. Attach the Safety Key on to the treadmill console. 2. Stand on the treadmill and straddle belt. Attach safety key clip to your clothes. 3. Press POWER button. There will be an eight (8) second delay after pressing the POWER button before data can be entered. The TIME window will fla[...]

Pr og r am and Oper a tion PROGRAM MODE Plug treadmill into a surge protector outlet. Attach the Safety Key on to the treadmill console. 1. Stand on the treadmill and straddle belt. Attach safety key clip to your clothes. 2. Press POWER button. There will be an eight (8) second delay before data can be entered. The TIME window will flash. 3. There [...]

Pr og r am Pr ofiles 16 The Fat Burn Program is designed to vary the treadmill elevation, while maintaining a constant walking belt speed. The Cardio Program is designed to vary the treadmill Speed, while maintaining a con- stant Elevation. The W arm Up Pr ogram is designed to gradually increase the treadmill Speed and Elevation in the first segmen[...]

Belt Adjustment W ARNING! Do not over -tighten r ollers! This will cause prema- ture r oller bearing failure! Belt adjustment and tension performs two functions: adjustment for tension and centering. Y our new treadmill comes pre-adjusted from the factory for tension and centering. Please follow the procedures below if the belt shifts to the left o[...]

Change MPH to KMH Y our treadmill will operate in British Units (miles per hour) or International Units (kilometers per hour). All treadmills are calibrated at the factory for British Units (miles per hour). T o change the display to read in kilo- meters, follow the steps described here: 1) T urn power OFF on the console. (Do not unplug treadmill.)[...]

Maintenance Instr uctions W ARNING! Before performing any maintenance to your treadmill, always unplug the power cord from the surge protector . CLEANING: Routine cleaning of your T riumph 7.3t T readmill will extend the life of your unit. W ARNING! T o prevent electrical shock, be sure the power to the treadmill is OFF and the unit is unplugged fr[...]

T roubleshooting Guide T r eadmill will not start . 1. Is the Safety Key inserted into the treadmill Console? 2. Make sure the power cord is plugged into a surge protector , the sur ge protector is plugged into a properly grounded outlet, and the surge protector is turned on. (Refer to “Power Requirements” on page 12 .) 3. Check the circuit bre[...]

Er r or Messa ges T readmill Err or Messages . Y our treadmill is equipped with a software package that enables error messages to be displayed when there is a problem. The following error codes will be displayed in the console display windows. Safety Interlock Err or Messages SI 1 - Safety key missing, replace and try again. SI 2 - Over voltage pro[...]

Calibr a tion Sequence Do not attempt to calibrate the treadmill unless an Err or Code is present. See Err or Messages (page 21). Our treadmill is equipped with a software package that will perform a calibration sequence unique to your specific model number . Please perform the following steps to calibrate the T riumph 7.3t T readmill. 1. Unplug po[...]

P ar ts List REF# KEYS PART# DESCRIPTION QTY. REF# KEYS PART# DESCRIPTION QTY. 1 423-00008 Cross Bar 1 54 402-00046 Clip Nut 8 2 406-00055 Base Bumper 2 55 406-00099 Transport Wheel, Clear 2 3 406-00056 Long Bumper 2 56 404-00004 Poly V-Belt 190J8 1 4 423-00009 Left Upright 1 57 404-00008 Walkbelt, Triumph 7.3T, No Logo 1 5 423-00010 Right Upright [...]

P ar ts List REF# KEYS PART# DESCRIPTION QTY. REF# KEYS PART# DESCRIPTION QTY. 110 414-00002 Safety Key Decal 1 139 407-00007 Motor Controller 1 112 410-00034 Zip tie small 4 140 407-00008 EKG Module 1 113 410-00035 Zip tie large 15 141 413-00019 Tel-line 1 114 402-00081 Plastic Washer 18 142 407-00006 Speed Incline PCB 2 115 402-00082 Washer 9x 22[...]

Exploded V iew 25[...]

Exploded V iew 26 CONSOLE ASSEMBL Y WIRE HARNESS[...]

W ar r anty Inf or mation 27 Keys T riumph 7.3t T readmill KEYS FITNESS PRODUCTS, LP – LIMITED W ARRANTY PLEASE CONSUL T YOUR PHYSICIAN BEFORE USING THIS PRODUCT . This Limited W arranty applies in the United S tates and Canada to products manufactur ed or distributed by Keys Fitness Products, LP (“Keys”) under the KEYS brand name. The warran[...]

Customer Ser vice (888) 340-0482 K eys Fitness Pr oducts 4009 Distribution Drive Suite 250 Garland, TX 75041 www .keysfitness.com[...]