Casablanca Fan Company 46U73D инструкция обслуживания

13 C APISTRANO ™ O WNER ’ S M ANUAL Casablanca[...]

1 CIRCUIT BREAKER (TRIP BREAKER FOR THE CIRCUIT YOU WILL BE WORKING ON) FUSE BOX (REMOVE FUSE FOR THE CIRCUIT YOU WILL BE WORKING ON) 18 ″ 84 ″ 70 ″ • The blad es in each pack are m atched f or equ al weigh t to assur e smooth f an operati on. If mor e than on e fan is being in stalled, be car eful not to mix blades fr om differ ent cartons[...]

2 Calculation of 32 ° Use th e tear-o ff Ceiling Angle T emplate card in serted in th e back of this m an ual, it provi des you with a simple ‘go’ or ‘no-g o’ for installing your f an on a sloped ceiling. SLOPED CEILING INST ALLA TIONS MOUNTING RECOMMEND A TIONS 7 ′ MINIMUM P ole Length Standard Standard 6 ″ 12 ″ 12 ″ 18 ″ 24 ″[...]

3 PREP ARA TION INSTRUCTIONS Unpackin g: Befor e assembling and in stalling your ceilin g fan, r em ove all parts from the shippin g cartons and ch eck them against th e parts listed here . Before discar ding pack aging materi al, be certain that all parts have been rem oved. CEILING HARDW ARE CROSSBAR MOUNTING BRACKET WIRE NUT (4) FAN PREP ARA TIO[...]

4 CAUTION: T o reduce the risk of personal injury , use only the mounting hardw are pr ovided with the appro ved outlet bo x to install the crossbar mounting br acket. CROSSB AR MOUNTING BRA CKET INST ALLA TION CEILING WIRING CROSSBAR MOUNTING BRACKET FLA T W ASHER GREEN GROUND WIRE CEILING F AN APPROVED OUTLET BOX RIDGE SIDE DOWN CANOPY INST ALLA [...]

5 CANOPY ELECTRICAL CONNECTIONS Step 4a. Attach th e fan wir es to the ceilin g fixture outlet box wirin g by placing th e bare en ds o f the wir es sid e by sid e and th en securin g with a wire nut. T est that the connecti on is secure by pullin g on the wir e nut. Conn ect in this order: Step 4b . • GREEN leads from m ountin g plate and fan to[...]

6 RUBBER GROMMET (4 PER BLADE) BLADE SCREW (4 PER BLADE) BLADE & BLADE HOLDER HARDW ARE BLADE HOLDER BLADE HOLDER SCREW (2 PER BLADE) Step 9. Insert a rubber gr ommet through each blade h ole o f every blade . Inspect both sid es of th e blade to assure that the lips o f the grommet ar e fully engaged . RUBBER GROMMET INST ALLA TION CORRECT INS[...]

7 BLADE/BLADE HOLDER INST ALLA TION Step 12. Usin g the five screws rem oved in Step 11, and th e five addition al screws fr om the pack, attach each blad e/blade hold er as- sembly to the m otor . Usin g the screwd river , tighten secur ely by hand only . Step 10. Attach each blad e to a blad e hold er securing it with th e f our blade scr ews pro[...]

8 COMPLETING INST ALLA TION Step 14. Hold th e switch housin g up to the f an and conn ect th e motor plug to the switch h ousing socket. Th e connec- tor is keyed to en sure corr ect in stallation. PREP ARA TION CONNECTING THE SWIT CH HOUSING ASSEMBL Y Step 13. Locate the switch h ousin g/cap assembly and r emove th e two 8-32 X 3 / 8 ″ screws h[...]

9 INST ALLING THE SWITCH HOUSING ASSEMBL Y Step 17. Line up th e two clearance h oles in the cap with th e two threaded h oles on th e r aised rim o f th e switch housing. Press th e cap onto the switch h ousing to seat th e guid e pins in to the ali gnmen t h oles of th e switch housin g. Step 18. U sing th e two (2) 8-32 X 3 / 8 ″ scr ews rem o[...]

10 3-SPEED ♦ W -8/W-811 WALL CONTROL OF THE FAN & LIGHT(S) 3-SPEED ♦ W -4/W-411 WALL CONTROL OF THE FAN • The f an may be turn ed ON and OFF by the W-8/W-811 wall con trol. • Th e li gh ts m ay be turned ON and OFF by the W-8/W-811 an d the inten sity adjusted from low to high. • The f an must be suppli ed with two ind epend ent 120V [...]

11 COLLAR SWITCH HOUSING 3-SPEED ♦ OPTIONAL LIGHT FIXTURE INST ALLA TION REVERSE SWITCH 3-SPEED ♦ OPERA TION Pull-chain switches on th e fan con trol the f an and li ghts . Usin g the f an contr ol pull-chain switch: Fan off at start. First pull: fan ON, low speed Second pull: medium speed Third pull: high speed Fourth pull: fan OFF Usin g th e[...]

12 TROUBLESHOO TING Befor e Requesting Service: Please follo w this troubleshooting guide befor e contacting your dealer f or assistance. Caring for Finishes : For cleanin g, a soft brush or lin t-free cloth should be used to pr event scr atchin g the finish. A vacuum cleaner brush nozzle can r emove heavi er dust. Surf ace smud ges or an accu- mul[...]

14 ©C OP Y R I GH T 1998 C AS ABL ANC A F AN C OM P A N Y • U . S . P ATENT P EN D I N G P RI N TED IN RO C 761 C O RP O RATE C EN TER D RI VE • P OMON A , C A 91768 • 800- 759- FA N S ( 3267)[...]