Casablanca Fan Company 46XXD/M инструкция обслуживания

1 CIRCUIT BREAKER (TRIP BREAKER FOR THE CIRCUIT YOU WILL BE WORKING ON) FUSE BOX (REMOVE FUSE FOR THE CIRCUIT YOU WILL BE W ORKING ON) 18 ″ 84 ″ 70 ″ • The blad es in each pack ar e matched f or equ al weigh t to assur e smooth fan oper ati on. If mo re than one f an is being in stalled, be car eful not to mix blades fr om differ ent carton[...]

2 Calculation of 32 ° U se th e tear-o ff Ceiling Angle T emplate card in serted in th e back of this m anu al, it provi des you with a simple ‘go’ or ‘no-g o’ for installin g your fan on a sloped ceilin g. SLOPED CEILING INST ALLA TIONS MOUNTING RECOMMEND A TIONS 7 ′ MINIMUM P ole Length Standard Standard 6 ″ 12 ″ 12 ″ 18 ″ 24 ?[...]

3 PREP ARA TION INSTRUCTIONS U npackin g: Befor e assembling and in stalling your ceilin g fan, r emove all parts from the shippin g cartons and ch eck them against th e parts listed here . Before discar ding packaging m aterial, be certain that all parts have been r emoved . CEILING HARDW ARE CROSSBAR MOUNTING BRACKET WIRE NUT (4) FAN PREP ARA TIO[...]

4 CAUTION: T o reduce the risk of personal injury , use only the mounting hardw are pr ovided with the appro ved outlet bo x to install the crossbar mounting br acket. CROSSB AR MOUNTING BRA CKET INST ALLA TION CEILING WIRING CROSSBAR MOUNTING BRACKET FLA T W ASHER GREEN GROUND WIRE CEILING F AN APPROVED OUTLET BOX RIDGE SIDE DOWN CANOPY INST ALLA [...]

5 5 CANOPY ELECTRICAL CONNECTIONS Step 4a. Attach the fan wires to the ceiling fixture outlet box wiring by placin g the bare ends of the wir es sid e by sid e and then securin g with a wir e n ut. T est that the conn ection is secure by pullin g on the wire n ut. Connect in this or der: Step 4b . • GREEN leads from moun ting plate and fan to GRO[...]

6 RUBBER GROMMET (4 PER BLADE) BLADE SCREW (4 PER BLADE) BLADE & BLADE HOLDER HARDW ARE BLADE HOLDER BLADE HOLDER SCREW (2 PER BLADE) Step 9. Insert a rubber gromm et through each blade h ole of every blad e . Inspect both sid es of th e blade to assure that the lips o f the grommet ar e fully engaged . RUBBER GROMMET INST ALLA TION CORRECT INS[...]

7 BLADE/BLADE HOLDER INST ALLA TION Step 12. U sing th e five scr ews removed in Step 11, and th e five addition al screws fr om the pack, attach each blad e/blade hold er as- sembly to the m otor . U sin g the screwd river , tighten secur ely by hand only . Step 10. A ttach each blade to a blad e h old er securing it with th e four blad e scr ews [...]

8 COMPLETING INST ALLA TION Step 14. If your fan is a V ersa•T ouch 2 mod el, please skip to Step 15. For 3-Speed mod els, hold th e switch hous- ing up to th e fan an d conn ect the m otor plug to the switch h ousing socket. Th e connector is k eyed to ensur e correct in- stallation. PREP ARA TION (3-SPEED ONL Y) CONNECTING THE SWIT CH HOUSING A[...]

9 INST ALLING THE SWITCH HOUSING ASSEMBL Y Step 18. Line up the two clear ance holes in the cap with th e two thread ed holes on the r aised rim o f the switch housin g. Press th e cap onto the switch h ousing to seat the gui de pin s into the ali gnmen t h oles o f the switch h ousing. Step 19. U sing th e two (2) 8-32 X 3 / 8 ″ scr ews removed [...]

10 3-SPEED ♦ OPERA TION COLLAR SWITCH HOUSING 3-SPEED ♦ OPTIONAL LIGHT FIXTURE INST ALLA TION Pull-chain switch es on the fan con trol the f an and li ghts . U sin g the fan con trol pull-chain switch: Fan o ff at start. First pull: fan ON, low speed Second pull: medium speed Third pull: high speed Fourth pull: fan OFF U sing th e option al lig[...]

11 3-SPEED ♦ W-80 WALL CONTROL OF THE FAN & LIGHT(S) 3-SPEED ♦ W -40 WALL CONTROL OF THE FAN •T he f an may be turn ed ON and OFF by the W-80 wall con trol. •T he lights m ay be turn ed ON an d OFF by the W-80 an d the inten- sity adjusted from low to hi gh. •T he f an must be suppli ed with two ind ependen t 120V AC supply wires . ?[...]

12 TROUBLESHOO TING Befor e Requesting Service: Please follo w this troubleshooting guide befor e contacting your dealer f or assistance. Caring for Finishes : For cleanin g, a soft brush or lin t-free cloth should be used to pr event scr atchin g the finish. A vacuum cleaner brush nozzle can r emove heavi er dust. Surf ace smud ges or an accu- m u[...]

13 SCREW 6-32 X 1” (2) SCREW 6-32 X 3 / 8 ” (2) W OOD SCREW 1” (2) DRYW ALL ANCHOR 6-32 (2) 12V BATTERY W -72 CONTROL W -72 CONTROL HOLDER VERS A•T OUCH 2 ♦ INST ALLA TION VERS A•T OUCH 2 ♦ CONTROL BRA CKET INST ALLA TION Standar d Light Switch Step A. Remove th e two screws h oldin g the switch cover plate . Do n ot remove th e cover[...]

14 SEND SIGNAL LED VERS A•T OUCH 2 OPERA TION F an Contr ol To start the f an. Press the selected speed button to run th e fan at th e desir ed speed. LO=Low speed MED=Medium speed HI=High speed To turn off the f an. Press th e F AN OFF button. Airflo w Dir ection To r everse the airflow pr ess the REVERSE button. Reverse operates at an y speed w[...]

15 Befor e Requesting Service: Please follow this tr oubleshooting guide before cont acting your dealer f or assistance . PROBLEM POSSIBLE REMEDIES PROBLEM POSSIBLE REMEDIES .. F AN WILL NOT ST ART •Check m ain circuit fuses , circuit break ers, or wall switch position. Ch eck all wire conn ection s, m aking sure th e power is turned o ff durin g[...]

16 PRODUCT SPECIFICA TIONS Model Name: Capistrano ® Model Number: 46XXD/M and 46UXXD/M Dimensions: A = 11 . 1 " B = 12.75" C = 3" D = 12.6" E = 5.6" Weight: 21 lbs. Motor: 188mm x 20mm Direct Drive ™ Blade Span With: 45" or 53" Blade Pitch: 16° No. of Blades: 5 T echnology: 3-Speed V ersa•T ouch2 ® W-72 Air[...]