Diamond Audio Technologies D3 1000.1 инструкция обслуживания

D3 400.2 | D3 500.4 | D3 600.1 | D3 1000.1 AMPLIFIER INST ALL A TION MANUAL[...]

2 Congratulations! Thank you f or choosing a Diamond Audio T echnologies D3 Series amplier . We sincerely believe that DA T products offer you outstanding per - formance and value. DAT products are engineered and produced with the highest quality materials and incorporate the latest technology . We think you will nd your new DA T amplier m[...]

3 Fr equency Response: 20Hz to 20KHz +/-3 dB Signal to Noise Ratio: > 95dBA (20 to 20kHz) Channel Separation 50dB THD+N(T otal Harmonic Distortion + Noise) < 0.2% (Output-1W 4 Ohms) RCA Input Sensitivity: 150mV to 4V RCA Input Impedance: > 20K Ohms Min to Max V oltage r equir ements 10.2V to 15.5V DC High/Low Pass Cr ossover: 12dB/Oct, 30-[...]

4 Connections and Contr ols This section describes how all of the terminals and adjustments of D A T D3 Series ampliers function. D3 400.2 2-Channel Amplifier 218 x 57.5mm D3.400.2 D3.600.1 D3.500.4 D3.1000.1 25A 25A 30A 30A 25A 25A 25A 30A 30A 30A 30A 0dB +12dB 0dB +12dB L R L R GAIN MIN MAX BASS BOOST 0dB +12dB HPF 30Hz BASS BOOST 0dB +12dB P[...]

5 RCA Input and Pass-Thru Output - These RCA jacks allo w for a normal Left and Right channel signal input. Simpl y connect to the sourc e unit using RCA type audio cable s, keeping them away from power wiring wherever possible. On the 4 channel amplifiers (D3 500.4) “Fr ont” and “Rear” input jacks are presen t as well as a “Pass-Thru”[...]

6 Installation Guidelines T ools and Supplies Listed bel ow ar e the tools and supplies needed to compl ete this ins tallation: • V olt/Ohm Meter • Wir e stripper s and wir e cutters • #2 Phillips scr ewdriver • Battery post wr ench • Hand held drill w/assorted bits • High quality el ectrical tape or heatshrink tubing • Soldering ir o[...]

7 Mounting Locations Engine Compartment Never mount this unit in the engine compartment. Mounting the unit in the engine compartment will void your warr anty . T runk Mounting Mounting the amplier vertic ally will pr ovide adequate cooling of the amplier . If you will be mounting it to an exis ting panel, be sur e it’ s not pr one to e xc e[...]

8 3) T rim the power cabl e within 18 inches (45.7mm) of the positive battery post and splice in a in-line fuse holder . DO NOT inst all the fuse at this time. 4) Strip 1/2 inch (12.7mm) from the battery end of the power cable and crimp a lar ge ring terminal to the cabl e. Connect the ring terminal to the positive (+) battery pos t. 5) Pr epa r e [...]

9 25A 25A 25A FUSE REM GND +12V BRIDGE L R – – + + + – Connecting Multiple Speak ers If you must connect more than one speaker per channel, there ar e two methods in which to do so: Series or Parall el. Parall el connections are harder on the amplier than series connections, as the total impedance is low er compar ed to driving a singl e s[...]

10 Installing the Remote Le vel Contr oller The D3 600.1 and the D3 1000.1 come packaged with a r emote le vel contr ol. This allows you to contr ol the lev el by attenuating the amplitude or increasing (up to the maximum set-point) of the amplier’ s input gain contr ol. This contr ol does not add additional bass boost, it simply allo ws you t[...]

11 Adjustment of Built-In Cros sover (All Models) Placing the switch in the HP position sets the amplier to the High Pass mode, enabling fr equencies above the cut off point to pass. Placing the switch in the LP position sets the amplier to the Low Pass mode, enabling frequencies belo w the cutoff point to pas s. Placing the switch in the OFF[...]

041807 Diamond Audio W arr anty Diamond Audio T echnol ogies, LL C (D A T) warrant s this pr oduct to be fr ee fr om def ects in mate- rial and workmanship for a period of one (1) year fr om the original date of pur chase pr ovided it was pur chased from an authorized DA T r etail er within the United States. Howev er, if this pr oduct was install [...]