Elite Screens R135WH1 инструкция обслуживания

Rev . 042409-JA www .elites creens.com info@elitescreens.com Elite Ez-F ra me Series Fixed Frame Projection Screen User’ s Guide[...]

Parts List 1. Fram e Parts x 6 pcs (4 top frame pcs. + 2 si de frame pcs) 2. Tension Rods x 6 pcs (4 top/bottom rods + 2 side rods) 3. Screen Material x 1 pc 4. Center joints x 2 pcs 5. Elbow Joints x4 pcs 6. Wall brackets x 2~3 pcs 7. Screws x 16 pcs 8. User Guide x 1 pcs 9. Center Support Bar x 1~2 pc s (depending on model) 10. Support joiner x 2[...]

Please do not tighten the screws completely, to mak e sure the frame piece lines up correctly . 3. Insert both corner joint connectors into the long horizontal fra me (see fig.1) 4. (2) Push Push Short frame Short frame Push Push Joint Long frame ( fig.1)[...]

Push Push ( fig.2) Insert the exposed ends of the joint connect ors into the short (vert ical) frame and align the four corners so that they meet at pe rfect righ t angles 4. Join all four frame parts together following the steps showed below. (fig.2) 5. After making sur e that all four corners join at r ight angles to form a perfect re ctangle, fa[...]

T ension Rod (Ho rizontal) x 4 T ension Rod (V ertical) x 2 T ension Rod (horizontal) Push T ension Rod (V ertical) Attaching the screen material to the frame 1. Lay out the screen and tension rods on a cl ean and dr y surface. Insert the scr een tension rods through the sleeves according t o their corresponding lengths on each edge of the screen a[...]

Black backing for Acoust icPro1080 models This procedure only applies to AcousticPro1080 models, disregar d if your ezFrame is no t an AcousticPro1080 variant. The bl ack backing counters the eff ect s of light penetration that would otherwise light up all items behind the scre en and spoil the picture.  （ fig.6 ） (5) Fix plate secures Acous[...]

Attaching the Fix Plates ___ 1. Make sure that the material and frame are both laying face down on a clean, dry and non-abrasive surface. 2. Center the mat erial inside th e frame. Please note the mater ial will be noticeabl y smaller because stretching the material is required to create a sufficient amount of tension for perfec t material fl atnes[...]

3. Slide the top end of the bar into the top center point location to complete center support bar insta llation. This will provide added stability to your frame and added tension to the material. Installa tion 1. Locate your desired installation lo cation with a stud finder (recommended) and mark the drill-hole area of where the screen is to be ins[...]

CAUTION Please follow these instru ctions carefully to ensure proper maintenance and saf ety with your ezFram e Screen 1. When hanging the screen up, please make sure th at no other objects such as power switches, outlets, furniture, ladders, windows, etc. occupy the space designated for your Fixed-Frame screen. 2. Regardless if the screen is hung [...]

W ARNING • The pr ojection screen frame is made of high- quality aluminum alloy and should be handled with care. • Use a soft cloth w ith warm water to rem ove any spots on the screen surface. • T o avoid damaging the scr een material, never atte mpt to use any solutions, chemicals or abrasive cleaners on the screen itself and neve r attempt [...]

Register your warranty at www.elitescreens.com/register.html US & Canada T ech Support & W arra nty Claim Please contact us at service@elit escreens.com or call +1 877-51 1-1211 # 3 Service Eur ope T ec h Support & W arranty C laim Please contact us at service@elit escreens.eu or call +49-(0) 40-3 0392958 Asia o r Ch in a T ech Support [...]