EV Rider Stand N Ride инструкция обслуживания

USER’S MANUAL EV Rider, LLC 6410 Arc Way • Suite A • Fort Myers • FL 33966 www.evrider.com • 1.800.944.1997[...]

IMPORTANT SAFETY NOTICE It is important to read and follow all the instructions and safety information contained in this Owner's Manual prior to use. - Always wear a safety helmet (which is provided with each SNR scooter). - Do not operate at night. - Comply with all local laws and regulations. - Do not use in wet conditions. - Do not use off [...]

TABLE OF CONTENTS Important Safety Information General Information Riding T errain Mechanical Systems About the Batteries Additional Safety Information Stand N Ride Overview Diagram Assembly Instructions Tiller Assembly Base Frame Assembly Installing the Optional Seat Assembly Coupling the Tiller to the Base Frame Installing the Battery Pack Before[...]

IMPORTANT SAFETY INFORMATION It is important to read and follow the instructions and the safety information contained within this owner's manual prior to use. General Information The SNR is a recreational battery-operated vehicle. It is not a mobility device for medically prescribed use and should not be used as such. Always wear a helmet when[...]

Mechanical Systems Check all joints, hinges and quick releases to ensure that the Stand N Ride is properly assembled. Stop using the product immediately if any joint, hinge or quick release becomes loose. Re-tighten the joint, hinge or quick release prior to resuming the ride. The electric motor , batteries and controls can get damaged if exposed t[...]

Additional Safety Information Adjust the handle bar height to provide a comfortable and secure riding position on the Stand N Ride scooter . The rider's hands should be able to easily grasp the handle bar controls (throttle and brake lever). They should not be higher than the waist or lower to ensure proper posture and riding control of the un[...]

Stand N Ride Overview FWD/REV Headlight Horn Fast/Slow Battery Gauge ON/OFF Brake Throttle Hub Motor/Drive Wheel Rear Wheel Anti-Tippers Battery Pack T ake-Apart Optional Seat Basket Page 6[...]

Assembly Instructions Your Stand N Ride is shipped in two boxes: 1 containing the tiller and 1 containing the base frame. After you have removed the Stand N Ride components from the protective packaging, you are ready to set up your scooter for riding by following these steps: Tiller Assembly: - Loosen the tiller height lock to allow for the insert[...]

Installing the Optional Seat Assembly: Locate all the seat assembly components and have them at hand to begin the installation of the seat assembly (Fig 5). - Remove the seat-post locking collar from the main seat-post tube to allow insertion of the tube through the base frame from the bottom up (fig 6). - Flip the base over to the side and insert [...]

Coupling the Tiller to the Base Frame: - Remove the secondary safety knob from the tiller coupler pin to allow the pin to slide through the base frame receiver . - Align the tiller coupler pin with the base receiver tube and slide it over the tiller pin (Fig 11). Wiggle it lightly until the locking spring locks in place. The wire connector would ha[...]

Before You Ride Checklist Before riding the Stand N Ride electric scooter , be sure to carefully follow the checklist below: - Read and understand the Important Safety information section of your Owner’ s Manual. - Make sure that the battery pack has been fully charged. - Check that the battery pack connection to the base frame is tight. - Check [...]

the unit and become proficient riding it. 7. Gr adually apply the throttle until the desired speed is achieved. Once again, we recommend that you do not venture to full speed operation until you have become proficient with the scooter and only if you are certain that there are no obstacles in site on an open field. 8. Make sure to slow down your sp[...]

Basic Maintenance The Stand N Ride has been designed to provide years of trouble-free riding enjoyment, provided that the user takes care of it by not leaving it exposed to the elements, neglecting to charge it or by using it in any way that is not recommended. Due to the Stand N Ride’s modular design, there are virtually no user serviceable part[...]

SNR-1000 Black T extured ABS Plastic & Metallic Silver Frame 992 mm / 36.3 in 642 mm / 25.3 in 75 mm / 3 in 136kg / 300 lb (With optional flat-free tires) 19.8 kg / 43.5 lb 18.42 kg / 40.5 lb 12.59 kg / 27. 7 lb 5.85 kg / 11 lb 56.66 kg / 122.7 lb 24 km/h / 15 mph Brushless DC hub motor , 24V , 500W 12.5” X 2.25” Pneumatic Optional flat-fre[...]

WARRANTY TERMS ONE-YEAR LIMITED WARRANTY One year on all structural frame components; including tiller , base frame and seat post (if purchased with this option). From one (1) year from the date of purchase, if any part or electronic component of the Scooter is found upon examination to be defective in material and/or workmanship, it will be repair[...]

NOTES Page 15[...]