Fujitsu SK-TSC-1125S инструкция обслуживания

Fujitsu Microelectronics Europe FMEMCU-UG-010003-11 User Guide TSC FMA1125 TOUCH SENSOR CONTROLLER SK-TSC-1125S QUICK START GUIDE[...]

SK-TSC-1125S User Guide - 2 - © Fujitsu Microelectronics Europe GmbH Revision History Date Issue 2009-11-11 V1.0, CHa, first official version 2009-12-15 V1.1, CHa, disclaimer updated, some corrections This document contains 19 pages NOTE: The FMA1125 touch sensor controller is developed and owned by ATLab Inc., South Korea, and is distributed by F[...]

SK-TSC-1125S User Guide © Fujitsu Microelectronics Europe Gmb H - 3 - Warranty and Disclaimer The use of the deliverables (e.g. soft ware, application examples, target boards, eval uation boards, starter kits, schematics, engineeri ng samples of IC’s etc.) is subject to the co nditions of Fujitsu Microelectronics Europe G mbH (“FME”) as set [...]

SK-TSC-1125S User Guide - 4 - © Fujitsu Microelectronics Europe GmbH 0 Contents REVISION HISTORY .............................................................................................................. 2 WARRANTY AND DISCLAIMER ........................................................................................... 3 0 CONTENTS ..........[...]

SK-TSC-1125S User Guide © Fujitsu Microelectronics Europe Gmb H - 5 - 1 Overview 1.1 Abstract The SK-TSC-1125S Starter Kit allows easy evaluation of the FMA1125 Touch Sensor Controller. It consists of the following parts: • 1x SK-TSC-1125S-TB touch board with FMA1125 TSC • 1x ADA-16FX-TSC-LCD • 1x 10-pin ribbon cable • 3x FMA1125DC-24S Sam[...]

SK-TSC-1125S User Guide - 6 - © Fujitsu Microelectronics Europe GmbH 1.2 Features < FMA1125DC-24S Touch Sensor Controller (SSOP24 package) with 4-8 touch input channels and 4-8 digital I/Os (4 pins can be I/O or touch input ) < Connector for up to eight touch input channels, with ‘mini-slider’ on PCB < Four LEDs connected to TSC GPIO [...]

SK-TSC-1125S User Guide © Fujitsu Microelectronics Europe Gmb H - 7 - 2 Installation 2.1 Setup (Starter Kit Hardware) Carefully remove the PCBs from the shipping carton. Please follow the steps below to assemble the Starter Kit: 1. Connect the ribbon cable end with the pull relief to X1 on the ADA-16FX-TSC-LCD. Pin1 (Marked on the cable) of the ca[...]

SK-TSC-1125S User Guide - 8 - © Fujitsu Microelectronics Europe GmbH 2.2 Setup (PC Software) The installation of the USB driver is described in the SK-16FX-EUROSCOPE documentation. In case the USB connection is only used as power supply, the driver installation is optional. Communication with the demo fir mware also is possible using the standard [...]

SK-TSC-1125S User Guide Figure 2: System set-up (LCD and SK-16FX EUROSCOPE not included!) © Fujitsu Microelectronics Europe Gmb H - 9 -[...]

SK-TSC-1125S User Guide - 10 - © Fujitsu Microelectronics Europe Gmb H 2.4 Jumper settings 2.4.1 SK-TSC-1125S-TB Jumper Setting Description Open I2C SCL line not connected to Pull-up resistor JP1 (SCL pull- up) Closed I2C SCL line connected to Pull-up resistor Open I2C SDA line not connected to Pull-up resistor JP2 (SDA pull-up) Closed I2C SDA lin[...]

SK-TSC-1125S User Guide © Fujitsu Microelectronics Europe Gmb H - 11 - 2.4.2 ADA-16FX-TSC-LCD Jumper Setting Description Open I2C SCL line not connected to Pull-up resistor JP2 (SCL pull- up) Closed I2C SCL line connected to Pull-up resistor Open I2C SDA line not connected to Pull-up resistor JP3 (SDA pull-up) Closed I2C SDA line connected to Pull[...]

SK-TSC-1125S User Guide - 12 - © Fujitsu Microelectronics Europe Gmb H 2.5 I2C header (X1) pi nout (ADA-16FX-TSC-LCD) X5 Pin Name Connected to Descripton 1 SCL JP6, X3 Pin 1 I2C Serial Clock Line 2 SDA JP4, X3 Pin 2 I2C Serial Data Line 3 GND System Ground 4 VCC VCC for TSC and LCD 5 TINT X3 Pin 5 Touch interrupt from TSC to MCU 6 GINT X3 Pin 6 Ge[...]

SK-TSC-1125S User Guide © Fujitsu Microelectronics Europe Gmb H - 13 - 3 Basic Tuning Process using the Command Line Interface and a PC Terminal Program The SK-TSC-1125S kit can also be used together with a demo application running on the SK-16FX-EUROSCOPE to adapt settings like sensitivity and other parameters in the running application and to op[...]

SK-TSC-1125S User Guide - 14 - © Fujitsu Microelectronics Europe Gmb H Typically, to start tuning a new application, first of all the Reference Delay and Alpha settings need to be set. For this, the ‘mon2’ monitor mode can help to directly show the effect of changed settings. The Reference Delay is set by the ‘srd nn’ comm and, where ‘nn[...]

SK-TSC-1125S User Guide Figure 3: Monitor Mode (‚mon2’) In mon2 mode, channels with active touch status will be shown with stars ‘*’, those in inactive state are shown with lines ‘|’. © Fujitsu Microelectronics Europe Gmb H - 15 -[...]

SK-TSC-1125S User Guide - 16 - © Fujitsu Microelectronics Europe Gmb H 4 Related Products < SK-16FX-EUROSCOPE Evaluation board for the 16FX Family MB96340 Series MCU < SK-TSC-1127-SB Starter Kit for the FMA1127 Touch Sensor Controller with 12 channels[...]

SK-TSC-1125S User Guide © Fujitsu Microelectronics Europe Gmb H - 17 - 5 Information in the WWW Information about FUJITSU MICROELECTRONICS Products can be found on the following Internet pages: Touch sensor controllers: http://www.fujitsu.com/emea/se rvices/microelectronics/tsc/ Microcontrollers (8-, 16- and 32bit), Graphics Controllers Datasheets[...]

SK-TSC-1125S User Guide - 18 - © Fujitsu Microelectronics Europe Gmb H 6 China RoHS regulation This starter kit is compliant with China RoHS[...]

SK-TSC-1125S User Guide 7 Recycling Gültig für EU-Länder: Gemäß der Europäischen WEEE-Richtlinie und deren Umsetzung in landesspezifische Gesetze nehmen wir dieses Gerät wieder zurück. Zur Entsorgung schicken Sie das Gerät bitte an die folgende Adresse: Fujitsu Microelectronics Europe GmbH Warehouse/Disposal Monzastraße 4a D-63225 Langen [...]