Global Machinery Company LS620SR инструкция обслуживания

LS620SR 020919 LS620LSR ED9 • London • Melbourne • Perth • T aipei • V erona • Hong K ong • New Y ork • Auckland • Paris INSTRUCTION MANU AL 620W V ariable Speed Jigsa w with LightSabre[...]

Contents Introduction 3 Environment al protection 3 Symbols 3 Specifications 3 Safety rules for laser lights 3 General safety instructions 4 Additional safety rules f or jigsaws 5 Unpacking 6 Know y our product 7 Adjusting the shoe f or angular cutting 8 Dust extr action 8 Switching on and o ff 8 Adjusting the cutting speed 8 Making a cut 9 Pocket [...]

Dear Customer If you require any help with your product, whether it is a Warranty claim, spare part or user inf ormation: please phone our Help Line for an immediate response . The appropriate number is given on the rear page of this manual. Introduction Y our new GMC power tool will more than satisfy your expectations . It has been manufactured un[...]

• The laser shall be used and maintained in accordance with the manufacturer’ s instructions. • Never aim the beam at any person or an object other than the work piece . • The laser beam shall not be deliberately aimed at personnel and shall be prevented from being directed towards the eye of a person f or longer than 0.25s. • Always ensu[...]

cord away from heat, oil and sharp edges. 10. Secur e the work piece . Use clamps or a vice to hold the work piece . It is safer than using your hand and frees both hands to operate the tool. 11. Do not o verr each. Keep your f ooting secure and balanced at all times. 12. Look after y our tools . Keep tools sharp and clean f or better and safer per[...]

• Before cutting, check that there is sufficient clearance for the blade under the work piece . • Do not touch the blade after operation. It will be very hot. • Keep your hands away from under the work piece . • Never use your hands to remove sawdust, chips or waste close by the blade . • Rags, cloths, cord, string and the lik e should ne[...]

3 1 4 15 11 12 2 6 7 9 10 8 7 Know y our product Before using the jigsaw , familiarise yourself with all the operating features and safety requirements. Use the tool and accessories only for the applications intended. All other applications are expressly ruled out. 1. Laser light assembly 2. Laser light on/off switch 3. Laser light battery cover 4.[...]

Adjusting the shoe f or angular cutting Caution. Always ensure that the jigsaw is switched off and plug is removed from the power point before making any adjustments. 1. Loosen the 2 hex screws located on the underside of the tool using the he x key provided. 2. Move the shoe plate (10) backwards and tilt it to the required angle between 0 and 45°[...]

1. The electronic speed control dial (15) is used to programme the speed of the blade . 2. The speed should be adapted to the material being cut. 3. Use your thumb to turn the dial forward to increase the speed and backward to decrease it. 4. Position “1” denotes the lowest speed. P osition “6” denotes the highest speed. Making a cut 1. Swi[...]

3. Tighten the 2 hex screws . 4. Replace the plug and run the saw under no load to check that it runs smoothly before using it to cut any materials. Using the LightSabre s ystem W arnings. Do not stare directly at the laser beam. Never aim the beam at any person or an object other than the work piece . Do not deliberately aim the beam at personnel [...]

C a r e f u l l y r e a d t h e e n t i r e I n s t r u c t i o n M a n u a l b e f o r e u s i n g t h i s p r o d u c t . B e f o r e r e t u r n i n g t h i s p r o d u c t f o r a W a r r a n t y C l a i m o r a n y o t h e r r e a s o n P l e a s e C a l l 1 3 0 0 8 8 0 0 0 1 ( A u s t r a l ia ) o r 0 8 0 0 4 4 5 7 2 1 ( N e w Z e a l a n d )[...]