Godex RT230i инструкция обслуживания

RT200i/RT230i BARCODE PRINTER USER MANUAL User Manual Version Issue Date P/N : RT200i series : Rev. 1.4 : 2012.10.25 : 920-014511-00[...]

Declaration RT200i/RT230i USER MANUAL FCC COMPLIANCE STATEMENT FOR AMERICAN USERS This equipment has been tested and found to comply with the limits for a CLASS A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercia[...]

Safety instructions RT200i/RT230i USER MANUAL SAFETY INSTRUCTIONS Please read the following instructions carefully. 1. Keep the equipment away from humidity. 2. Before you connect the equipment to the power outlet, please check the voltage of the power source. 3. Make sure the printer is off before plugging the power connector into the power jack. [...]

Contents RT200i/RT230i USER MANUAL CONTENTS 1 Barcode Printer 001 1.1 1.2 Box Content Getting to Know Your Printer 001 002 2 Printer Setup 005 2.1 2.2 2.3 2.4 2.5 Open the Printer Loading the Ribbon Loading the Label Roll Module Connecting the Printer to the Host Computer Installing Printer Driver and QLabel with Super Wizard CD 005 006 010 013 015[...]

RT200i/RT230i Barcode Printer  1 Barcode Printer 1.1 Box Content Please check that all of the following items are included with your printer. 001 USB Cable  CD Including GoLabel software and RT200i/RT230i user manual.  Power Adapter Power Cord AC Adapter  RT200i/RT230i Quick Guide  Label Stock  Ribbon Module Empty Ribbon Core Ribb[...]

Front View  1 Barcode Printer 1.2 Getting to Know Your Printer 002 Device Overview Rear View  COVER RELEASE CATCHES Pull catches for opening the printer cover OPERATION PANEL FRONT COVER FEED BUTTON POWER BUTTON LCD SCREEN DIRECTION KEY ETHERNET PORT SERIAL PORT POWER JACK USB PORT CALIBRATION BUTTON USB HOST FAN-FOLD LABEL INSERT Feed slot f[...]

Bottom View  1 Barcode Printer 003 COVER OF THE MODULE CONNECTION JACKS * *** Cut-outs are not intended for wall-mount use.[...]

1 Barcode Printer The Internal View of Printer 004 RELEASE CATCH Release catch for closing the printer cover TOP COVER LABEL SUPPLY MODULE LABEL SENSOR MODULE LABEL SENSOR GUIDE TRACK PAPER PRESS BAR LABEL SUPPLY HUB LABEL GUIDES PLATEN MODULE PLATEN PLATEN LOCKERS RELEASE CATCH Release catch for opening the label supply hub The Printing Mechanism [...]

2 Printer Setup 2.1 Open the Printer Open the Printer Cover and the Printing Mechanism Place the printer on a flat surface. Open the printer cover by pulling the release catches on both sides of the printer and lift the cover. 005 Pull the catches toward the direction COVER RELEASE CATCHES Pull the catches for opening the printer cover Pull the cat[...]

2 Printer Setup 2.2 Loading the Ribbon 006 A New Ribbon Module Installation 1. Attach the ribbon to the empty ribbon core with the adhesive strip at the end of the ribbon. 2. Wind the ribbon around the empty ribbon core for 2 to 3 circles. 3. A ribbon module is assembled as below. EMPTY RIBBON CORE A NEW RIBBON Stick on empty ribbon core Notch on l[...]

2 Printer Setup 007 2. Then place the left-hand side of the ribbon. Load the Ribbon on the Printer For Ribbon Supply Module 1. Place the right-hand side of ribbon first. Right side Push the ribbon to tighten the spring of the holder Align the ribbon core to the holder SPRING OF HOLDER Left side Align the notch of the ribbon core to the spoke NOTCH [...]

2 Printer Setup 008 3. The ribbon supply module loading is completed. Load the Ribbon on the Printer For Ribbon Rewind Module 1. Pass the ribbon to round the print head. RIBBON REWIND MODULE Move the empty ribbon core upward to ribbon rewind mechanism[...]

2 Printer Setup 009 2. Place the right-hand side of empty ribbon core first. Right side Push the empty ribbon core to tighten the spring of the holder SPRING OF HOLDER Align the empty ribbon core to the holder 3. Then place the left-hand side of the empty ribbon core. Turn the ribbon wheel to align the notch of empty ribbon core to the spoke. Left [...]

2 Printer Setup 2.3 Loading the Label Roll Module 010 A New Label Supply Module Loading 1. Unlock the release catch to lift the label supply hub. LABEL STOCK LABEL SUPPLY HUB 2 1 Push rightward Lift the label supply hub upward 2. Place the label stock on the label supply hub. Place on the label supply hub[...]

2 Printer Setup 011 3. Push the label supply module downward and close the release catch. Push downward to fix the module 4. A new label supply module is completed. Loading the Label Roll Module on the Printer 1. Feed the Label through the label guides and adjust the label guides to the label width. The label guides will help to prevent the label s[...]

2 Printer Setup 012 2 Close the printer cover 1 Push the release catch 2. Unlock the release catch to close the printer cover. 3. Press the FEED key and make sure the label is fed smoothly. The label loading is completed now. * *** Please keeps the rack gear clean to ensure the smoothness of label holder.[...]

2 Printer Setup 2.4 Connecting the Printer to the Host Computer 013 1. Please make sure that the printer is switched off. 2. Connect the power cord to the AC adapter. AC ADAPTER POWER CORD Connect the jack of the power adapter to the printer and connect the plug of the power adapter to the socket of the wall. RT200i/RT230i BARCODE PRINTER POWER ADA[...]

2 Printer Setup 014 3. Connect the USB/serial cable to the printer and host computer. 4. Pressing the POWER button. The LCD screen should now lights up. Pressing the POWER button OPERATION PANEL POWER BUTTON LCD SCREEN RT200i/RT230i BARCODE PRINTER USB CABLE PC USB PORT PLUG PLUG[...]

2 Printer Setup 2.5 Installing Printer Driver and GoLabel with Super Wizard CD 015 1. Insert the Super Wizard CD in the CD/DVD drive of the host computer and the program should pop up automatically. You will see the Welcome screen first. On the Welcome screen, choose “Standard Installation”. 2. The wizard will then ask you to make sure your USB[...]

2 Printer Setup 016 4. As the printer driver and GoLabel are installing, a screen will display a progress bar. 6. As the optional steps, you can also print a test label or register your printer during the “Standard Installation” procedure. 5. Once the installation is complete, you can start to make and print labels with GoLabel or throug the pr[...]

2 Printer Setup 017 1. Insert the product CD in the CD/DVD drive of the host computer and open the "Seagull Drivers" folder on the CD. Select the icon for the driver file and click it to start the installation. 2. Follow the instructions on the screen. The Driver Wizard guides you through the installation procedure. Select "Install p[...]

2 Printer Setup 018 4. Specify the port used to connect the printer to the host computer. 6. Once the installation is complete, a summary of the printer settings is displayed. Check whether the printer settings are correct and click "Finish" to start copying the driver files. Wait until copying is complete, then finish the installation. 5[...]

2 Printer Setup 019 7. Once the driver installation is complete, the new printer should appear in the "Printers and Faxes" folder. Godex RT200i Godex RT200i[...]

3 Setting and Control for Operation Panel 3.1 Operation Panel 020 FEED Button When you press the FEED button, the printer moves the label to the defined stop position. If you are using continuous labels, pressing the FEED button will move label stock until you release the button again. If you are using individual labels, pressing the FEED button wi[...]

3 Setting and Control for Operation Panel 3.2 LCD Interface Introduction 021 Getting Started Press the POWER button to turn on the printer, and the START UP SCREEN appears. If the printer is on “ready to print” status, the LCD screen should display the message “Ready“ on the screen. Please keep pressing  button and wait for the timer to [...]

3 Setting and Control for Operation Panel 022 Operations on Setting Page On MAIN PAGE, press  or  button to move the cursor and select the functions. Select a designated function and press FEED button, you will enter the SETTING PAGES for the function. or Select Enter On SETTING PAGES, press  or  button to select the setting items. Sele[...]

3 Setting and Control for Operation Panel 023 Press FEED button will apply the setting value you just selected, and the red tick will appear to mark the value. On SETTING VALUE PAGES, press  or  button to change the setting values. or Select Apply * *** The blue arrow indicates the value you are selected. ** ** The red tick indicates that the[...]

3 Setting and Control for Operation Panel 024 On SETTING PAGES, press  button will go back to the MAIN PAGE screen. Exit from Current Page to Ready Status The icon on top-left corner displays the capture of upper level screen and also guides you back to upper level with left or up arrow. NAVIGATION ICON On SETTING VALUE PAGES, press  button w[...]

3 Setting and Control for Operation Panel 025 On MAIN PAGE, select the “EXIT” icon and press the FEED button to exit from SETTING MODE and the printer goes back to READY status. or EXIT from Setting Mode Back to the Ready status[...]

3 Setting and Control for Operation Panel 3.3 LCD Interface Function 026 Main Page Printer Setting Label Setting Device Analysis Exit Setting items for printer, ex. Printing speed, darkness. A ls o inc ludes a Printing W i zard for your ease of printing. Setting items for printing label, ex. Rotation, Printing position offset. Option modules and co[...]

3 Setting and Control for Operation Panel 027 Setting Items in Setting Mode Printer Setting Label Setting LCD Languag e English German 繁體中文 简体中文 Wizard Speed 2-5 or 7 Darkness 0-19 Media Type Label with Gap s Label with Mark s Continuous Printer Mode Direct Therma l Thermat Transf er Tear-off Pos i tion 0-40 Setting Darkness 0-19 Sp[...]

3 Setting and Control for Operation Panel 028 Device Analysis Exit Buzzer Apply Cancel Optional Sett i ng Option None Cutter Label Dispensor Applicator Pre-Print i ng Apply Cancel Serial Port Sett ing Baud Rate 4800 bps 9600 bps 19200 bps 38400 bps 57600 bps 115200 bps Parity Non Odd Even Data bits 7 bits 8 bits Stop bits 1 bits 2 bits RTC Setting [...]

3 Setting and Control for Operation Panel 029 Status of LCD Interface When printer is on standby status (ready to print), the LCD interface will display “Ready” on screen. You can only print on this “Ready“ status. If there is any printers error, the LCD screen will display the error screen to show the type of error. You can fix the error a[...]

3 Setting and Control for Operation Panel 3.4 Label Calibration and Self Test 030 Label Calibration The printer can automatically detect and store label height. That means the host computer does not need to transmit the label height to the printer. Self Test Self-test function lets you check whether the printer is functioning normally. Here is how [...]

3 Setting and Control for Operation Panel 031 Press CALIBRATION BUTTON Press Label Calibration Button A hardware button to make a Label Calibration while printer encountering ‘’Media Error’’ during the cases when first-time printer start up or change label or ribbon to another type, such as change using gap label to continuous or black mark[...]

3 Setting and Control for Operation Panel 3.5 Error Alerts 032 In the event of a problem that prevents normal functioning of the printer, you will see an error message on LCD screen and hear some beep signals. Please refer to below table for the error alerts. FEED BUTTON DIRECTION KEY OPERATION PANEL POWER BUTTON LCD SCREEN Operation Panel Status T[...]

3 Setting and Control for Operation Panel 033 Operation Panel Status Type Beeps Description Solution File Error 2 x 2 beeps The memory is full. The pr inter prints the messag e "File System full ". Delete unnecessary data or install additional memory. Unable to find file . The printer prints the messag e "File Name not found" Us[...]

3 Printer Setting and Control 3.6 USB Host 034 Definition : USB Host port supports either device ： USB memory stick, keyboard or scanner. Purpose  USB memory stick : It extends the user memory space up to 32GB for Graphic, Font, Label Format, DBF and Command files downloading. The printer’s Firmware also can be updating if copy new version o[...]

3 Printer Setting and Control 035 * * The USB Host port on ‘’i’’ ‘’x’’ model printer is without ‘’HUB’’ function. * * The USB Memory Stick supports with ‘’FAT32’’Disk Format and up to 32GB only. The certified venders are Transcend, Apacer, Patriot, Consair and Kingston. * The download function for Graphic, Font, Labe[...]

4 NetSetting for Ethernet 4.1 Installing the NetSetting software 036 The NetSetting software is used to manage the network configurations when connecting the printer via Ethernet port. It is available on product CD or can be downloaded from official website. To install the NetSetting, please follow below steps. 5. Click ”Next” to start the inst[...]

4 NetSetting for Ethernet 4.2 The Interface of NetSetting 037 Click the NetSetting icon to start the program; you will see the start page as below. The start page will display the basic information of connected printer and your PC. There are six tabs on the top of interface which can configure different types of network settings. But for the data s[...]

4 NetSetting for Ethernet 038 * *** To fully benefit from the NetSetting software, you should be familiar with basic networking principles. Please contact your network administrator for related network setting information. You can press “Set” button to apply the settings and “ReGet” button to refresh the setting values. IP Setting The IP Se[...]

4 NetSetting for Ethernet 039 You can press “Set” button to apply the settings and “ReGet” button to refresh the setting values. Alert Path Setting NetSetting will send the alert messages to designated mail account when the error happened on printer. The alert messages are sent by SMTP (Simple Mail Transfer Protocol) or SNMP (Simple Network[...]

4 NetSetting for Ethernet 040 You can press “Set” button to apply the settings and “ReGet” button to refresh the setting values. Alert Message Setting For the alert message notification function, you can decide which error cases need to be sent out to the operator. Moreover, the alert messages can be set to be sent by SMTP, SNMP or both.[...]

4 NetSetting for Ethernet 041 You can press “Set” button to apply the settings and “ReGet” button to refresh the setting values. Printer Configuration Set or change the configurations of connected printer. Most of key settings for the printer operation can be done by this setting page. RT200i[...]

4 NetSetting for Ethernet 042 You can press “Send Command” button to send printer commands via Ethernet port and control the printer remotely. User Command The “User Command” tab provides a communication interface for operator to control the printer. Input printer commands in "Input Command" window and press “Send Command” but[...]

4 NetSetting for Ethernet 043 In addition to the firmware update, you can press “Recover To Factory Settings” button to restore the printer configurations back to factory default. Firmware Download On “Firmware Download” tab, the current version of printer firmware will be showed on the screen. If you need to update the printer firmware, ju[...]

5 Accessories 044 Before installing the optional modules, please make some preparations as follows. 1. Turn off the printer Remember to switch off the printer before installing any module. 2. Open the printer cover and the printing mechanism Open the printer cover by pulling the release catches on both sides of the printer and lift the cover. Pleas[...]

5 Accessories 045 4. Remove the platen Lift up the release clips on both sides of the platen to release and pull upward the platen. CLIP Release the clip Pull up the platen 5. Ribbon loading Please see the Section 2.2 for further information about Loading The Ribbon. 6. Label loading Please see the Section 2.3 for further information about Loading [...]

5 Accessories 5.2 Installing the Label Dispenser 046 The Overview of the Label Dispenser PAPER SENSOR PAPER FEED ROLLER COVER CONNECTION CABLE OF LABEL DISPENSER * *** A label liner thickness of 0.006 mm ± 10% and a weight of 65 g/m 2 ± 6% are recommended. ** ** The label dispenser will take labels up to a max. width of 60 mm. *** * When using th[...]

5 Accessories 047 2. Place label dispenser to align both holes of screw and then tighten the screws. 3. Place the platen back to the printer and lock the clips. 4. Close the top cover and printing mechanism. Lock the clip CLIP 5. Turn the printer upside down.[...]

5 Accessories 048 6. Open the cover on the bottom of printer. 7. Plug the connector fo the label dispenser to the jack. 8. Close the cover of the module connection jacks. COVER OF THE MODULE CONNECTION JACKS Open the cover JACK CONNECTOR OF THE CONNECTION CABLE Plug COVER OF THE MODULE CONNECTION JACKS Close the cover * *** The printer must be swit[...]

5 Accessories 049 2. Feed the Label stock through the label guides. 3. Pull the label liner through the platen and the steel of the label dispenser. * *** Labels should be at least 25 mm high. Through the label guides LABEL LINER PLATEN STEEL Loading Label Roll with the Label Dispenser Module 1. Remove the first label from the label stock. Tear a l[...]

5 Accessories 050 4. The feeding path of label and liner should be as shown in below graphic. 5. Close the label dispenser and printer cover. The installation is completed now. Close the cover LABEL STOCK PLATEN ROLLER LABEL LABEL LINER[...]

5 Accessories 051 6. Press the FEED button to feed the label. The label will be peeled from the liner while it passes through the label dispenser. * *** There is a paper sensor on the Label Dispenser module. It will stop the printing if it is covered by label. Remove the last printed label and the printer will then continue to print next label. Pre[...]

5 Accessories 5.3 Installing the Cutter 052 The Overview of the Cutter * *** Remember to switch off the printer before installing the cutter. ** ** Do not use to cut adhesive labels! Glue residue will be left on the cutter blade and impair its functioning. The cutter has a blade life of 1000,000 cuts when using paper weighing 120g/m², and of 500,0[...]

5 Accessories 053 2. Place the cutter to align both holes of screw and then tighten the screws. 3. Place the platen back to the printer and lock the clips. 4. Close the top cover and printing mechanism. 5. Turn the printer upside down. Lock the clip CLIP[...]

5 Accessories 054 6. Open the cover on the bottom of printer. 7. Plug the connector for the cutter to the jack. 8. Close the cover of the module connection jacks. * *** The printer must be switched off, or the motherboard may be destroyed! ** ** There are 2 jacks : the lower jack for the label dispenser, the upper jack for the cutter. COVER OF THE [...]

5 Accessories 055 2. Close the top cover and printing mechanism. To finish, press the FEED button to set the label position. * *** We advise against using inside wound label stock. ** ** Labels should be at least 30 mm high. When using the printer with the cutter, you should set the stop position (^E) to 30. Installing the Label Roll Module on the [...]

6 Maintenance and Adjustment 6.1 Cleaning the Print Head 056 Dirt on the print head or ribbon, or glue residue from the label stock may result in inadequate print quality. The printer cover must therefore always be closed during printing. Keeping dirt and dust away from the paper or labels ensures a good print quality and a longer lifespan of the p[...]

6 Maintenance and Adjustment 6.2 Troubleshooting 057 * *** If any problems occur that are not described here, please contact your dealer. Problem Solution The printer is s wi tched o n but the LCD screen does not light up. ♦ Check the po w er supp ly. Please se e the Section 2.4 The LCD screen s how the notice icon and printing is interru pted. ?[...]

RT20 0 i /RT230 i USER MANUAL APPENDIX PRODUCT SPENIFICA TIONS Model RT200i RT230i Print Method Therm al Tran sfer / D irect Th erma l Resolution 20 3 dpi ( 8 dot s /mm) 300 dpi (12 dots/mm) Print Speed 7 IPS (1 77 mm/s) 5 IPS ( 127 mm/s) Print Width 2.12” (54 mm) 2.24 ” (5 6.9 mm ) Print Length Min. 0.16” (4 mm) ** ; Max. 68” (1727 mm) Min[...]

RT20 0 i /RT230 i USER MANUAL APPENDIX PRODUCT SPENIFICA TIONS Model RT200 RT230 Interfaces US B De vic e (B - Ty pe ) Seria l p or t: RS - 232 (D B - 9) US B Ho s t (A - Ty pe ) IEEE 802.3 10 /100Bas e - Tx Ethe rnet port (RJ - 45) US B De v ic e (B - Ty pe ) Seri al port: RS - 232 (DB - 9) US B Ho s t (A - Ty pe ) US B De vic e (B - Ty pe ) Seri [...]

Appendix INTERFACE RT200/RT230 USER MANUAL APPENDIX Pinout Description Connector Type : Type B Serial Port Default settings ： Baud rate 9600, no parity, 8 data bits, 1 stop bit, XON/XOFF protocol and RTS/CTS RS232 Housing(9-p in to 9-pin) DB9 Socket DB9 Plug - RXD TXD DTR GND DSR RTS CTS RI Computer 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 +5V, max 50[...]