Heat & Glo GRL-850-AU инструкция обслуживания

1 MODEL: GRL-850-AU AUSTRALIAN GAS ASSOCIA TION APPROVED Approval Number 5837 THIS MANUAL MUST BE USED FOR INST ALLA TION AND RET AINED BY HOMEOWNER FOR OPERA TION AND MAINTENANCE. HEA T -N-GLO, a brand of Hearth & Home T echnologies Inc. 20802 Kensington Boulevard, Lakeville, MN 55044, U.S.A. • (952) 985-6000 201 1-900C 7/03 INST ALLA TION A[...]

2 IMPORTANT: Read all instructions carefully before starting installation. Failure to follow these installation instructions may result in a possible fire hazard and will void the warranty. Save this Manual for future reference. Copyright 2003 Heat-N-Glo, a brand of Hearth & Home Technologies Inc. 20802 Kensington Boulevard, Lakeville, MN 55044[...]

3 Table of Contents 1.0 INTRODUCTION ......................................................................................................... 5 2.0 ASSEMBL Y ................................................................................................................. 5 GAS LINE CONNECTION .......................................................[...]

4 FIGURE 1 FIREPLACE OPENING Minimum Maximum WIDTH: 850mm 1050mm DEPTH: 300mm 460mm HEIGHT: 425mm 540mm DEPTH WIDTH TOP VIEW TOP VIEW - FIREPLACE AREA DECORATIVE FRONT CONTROL ACCESS COVER PILOT ASSEMBLY BURNER ON/OFF SWITCH GAS VALVE FLEX TUBE PIEZO IGNITOR REAR SURROUND FRONT SURROUND SIDE SURROUND 300mm DEPTH 33mm MINIMUM NOTE: Unit must be 33mm[...]

5 ! ! ! ! ! CAUTION: DO NOT PLACE ARTICLES ON OR AGAINST THIS APPLIANCE. CAUTION: DO NOT USE OR STORE FLAMMABLE MA TERIALS NEAR THIS APPLIANCE. CAUTION: DO NOT SPRA Y AEROSOLS IN THE VI- CINITY OF THIS APPLIANCE WHILE IT IS IN OP- ERA TION. W ARNING: THIS UNIT IS NOT FOR USE WITH SOLID FUEL. SOLID FUELS SHALL NOT BE BURNED IN A FIREPLACE WHERE A DE[...]

6 Figure 2 OPTIONAL WALL SWITCH, THERMOSTAT OR REMOTE REMOTE SWITCH PIGTAIL OFF ON ON/OFF SWITCH THERMOPILE TP/TH TP TH GAS VALVE THERMOCOUPLE A. Inlet gas supply pressure for purposes of input ad- justment, shall be 6.0 inches w.c. (1.5kPa) for natu- ral gas and 11 inches w.c. (2.75kPa) for propane. Manifold (outlet) pressure should be 3.2 inches [...]

7 1 5 2 3 4 6 7 LOG PLACEMENT INSTRUCTIONS STEP 1: Attach grate to as- sembly by sliding hooks into open- ings on the front surround . STEP 2: Ensure that tabs on the rear and side surround are bent as shown in Figure 1. Carefully remove logs from carton and place as shown. NOTE: Overhead view of burner, decorative front and surround. Log Set Assem[...]

Heat-n-Glo GRL-700/GRL-850 Glowing Embers (Mineral Wool) Placement Natural Gas • Place single layer of 10mm circular sized pieces next to burner ports, taking care not to place material on or between ports. • Do not use all of the ‘ember’ in the packet. One packet should last 5-6 applications. • Repeat application at the start of each sea[...]

Heat-n-Glo GRL-700/GRL-850 Glowing Embers (Mineral Wool) Placement LPG • Place single layer of 10mm circular sized pieces on top of burner ports. • Increase the quantity of the “glowing embers” on the right, centre and left hand side, as indicated, of the burner where there is a cluster of burner ports. • Do not use all of the ‘ember’[...]

8 STEP 3: LOG #1 (SR V201 1-707) Put log #1 behind the locating tab on the right rear corner and up against the locating tab in the center. STEP 4: LOG #2 (SRV530-717) Place log #2 on the left front corner of the grate using its locating groove and tab. STEP 5: LOG #3 (SR V201 1-703) Place log #3 onto the center of the burner using its locating tab[...]

9 STEP 7: LOG #5 (SRV 720-722 ) Rest log #5 on log #2 and rest the top in the grove on log #1. STEP 8: LOG #6 (SRV 347-712 ) Place log #6 in the groove on top of log #1 with its front on log #2. The left front edge of log #6 must be located 248mm from the left decorative front corner. STEP 6: LOG #4 (SRV568-706) Rest log #4 in the front right hand [...]

10 ! 3.0 OPERATING GUIDELINES AND MAINTENANCE INSTRUCTIONS Upon completing the gas line connection, a small amount of air will be in the lines. When first lighting the pilot light, it will take a few minutes for the lines to purge themselves of this air. Once the purging is com- plete, the pilot and burner will light and operate as indi- cated in t[...]

11 ! A. This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these in- structions exactly. B. BEFORE LIGHTING smell all around the appli- ance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor. C. Use only your hand to push in or turn the gas contr[...]

12 1. "STOP!" Read the safety information on previous page. 2. Remove the control access cover. 3. Turn the valve control knob to the "OFF" position. To do this, you must turn the knob clockwise to the "Pilot" position, and then press in and continue turning clockwise to the "OFF" position. GAS CONTROL VALVE [...]

13 Part number list on following page. (NG , LP) Exploded Parts Diagram Service Parts GRL-850-AU Beginning M anufacturing Date: 4-2003 Ending M anufacturing Date: ________ 13 Log set assembly 2 1 4 5 3 6 7 19 17 16 14 18 15 20 11 12 8 9 10 u[...]

14 4.0 REPLACEMENT PARTS: GRL-850-AU When requesting service or replacement parts for your decorative gas log set, please provide model number and serial number. All parts listed in this manual may be ordered from an authorized dealer. ITEM Description SERIAL # PART NUMBER 1 ON/OFF Rocker Switch 060-521A 2 Burner NG 2011-003 2 Burner LP 2011-005 3 [...]

15 LIMITED 10 YEAR WARRANTY HEAT-N-GLO, a brand of Hearth & Home Technologies Inc. In order to presumptively establish the dates to which your HEAT-N-GLO Limited Warranty runs, you must mail the completed warranty card to HEAT-N-GLO, a brand of Hearth & Home Technologies Inc., 20802 Kensington Boulevard, Lakeville, MN 55044, within 60 days [...]