Honeywell Smoke Alarm инструкция обслуживания

5/19/2008 1 of 15 Application Note: Fire-Lite IPDACT Set up for Installing Dealers These pictorial instructions should be used in conjunction with the formal PID (Product Installation Document) in cluded with the IPBRKT or IPENC as well as the instructions included with the IPDACT. Please Read all documentation prior to performing any installation [...]

5/19/2008 2 of 15 Note: All of the above available at Fire-Lite Distribution The IDPACT requires 24VDC filtered regul ated power and a phone pair from the DACT of the fire alarm control panel. While not required, it is highly re commended that any customer shared equipment used to connect the IPDACT to t he Internet such as router or hub be supplie[...]

5/19/2008 3 of 15 2. Mount the IPDACT onto the IPBRKT using the plastic standoffs that came with the IPBRKT. Screw the standoff through the holes on the IPDACT into the metal mating threaded stando ffs on the IPBRKT. Note, discard any double sided tape plastic standoffs that may be included with the IPDACT and use the supplied machine screw version[...]

5/19/2008 4 of 15 4. Loop the 8 PIN cable supplied with t he IPDACT once through the large Ferrite Ring. Note that this cable is NOT used as an Ethernet Cable but to interconnect the dialer output of the panel to the input of the IPDACT. Plug the 8 PIN cable supplied with t he IPDACT into the Primary DACT port of the control panel . Connect the oth[...]

5/19/2008 5 of 15 2. Installation using IPENC or HP300ULX The IPENC is used for mounting the IPDACT next to panels that cannot accept the IPBRKT directly inside the enclosure . Examples of these include the MS- 9200UD and MS-9600. Install the IPDACT onto the factory m ounted IPBRKT inside t he IPENC using the 4 supplied ¼”X 6-32 machine screws a[...]

5/19/2008 6 of 15 The IPDACT requires a minimum of 300 mA of current. If an FACP cannot supply this minimum requirement, a separate power supply, such as the HP300ULX, may be used to supply the r equired current. The IPDACT can be mounted inside the HP300ULX power suppl y enclosure as described below: 1. Position the IPBRKT bracket mounti ng hole a[...]

5/19/2008 7 of 15 Installation using 411UD for moni toring Alarm, Trouble and Supervisory dry con tacts from any FACP The 411UD can also be mounted next to the IPDACT inside the HP300ULX and used to monitor the Alarm, Trouble, and Supervisory dry contacts from any manufacturer’s fire alarm control panel. Please see the product installation docume[...]

5/19/2008 8 of 15 Set Connect using to COM1 then OK Note: if using a USB/Serial conver ter, select the COM port assigned to the converter •[...]

5/19/2008 9 of 15 • Set Port Settings to: Bits per second: 9600 Data bits: 8 Parity: none Stop bits: 1 Flow control: none ( very important ) Click OK • Press Enter and the word passw ord should appear as shown below • Key-in default IPDACT password 24680 as shown above then press Enter[...]

5/19/2008 10 of 15 • At the menu options screen, shown below, select " C: Quick Install "[...]

5/19/2008 11 of 15 • Note: The following examples contain only sample settings • Enter the parameters given to you by the Central Station for each menu item --Quick Install-- a) DHCP client: OFF when static IP will be us ed. Set this to ON if an IP will be obtained automatically from a network router on a private network. Select a) and then eit[...]

5/19/2008 12 of 15 e) Supervisory Main: 192.168.0.1 (note this is the primary receiver’s IP address assigned by central station) f) Supervisory Backup: 192.168.0.2 (note this is the secondary receiver’s IP address assigned by central station.) g) Maintenance: This is a third IP receiver setting that is not normally used. A third maintenance rec[...]

5/19/2008 13 of 15 secondary port will use the backup phone line for 24 hour test signals or when the network may go down. See your panel’s manual for correct programming. Do not forget to program t he panels 24 hour test parameters. ONBOARD DACT ENABLED = YES PRIMARY PHONE LINE = TOUCHTONE SECONDARY PHONE LINE = TOUCHTONE CENTRAL STATION REPORTI[...]

5/19/2008 14 of 15 The IP settings in the IPDACT work like this: • If you set the DHCP to ON, the IPDACT will broadcast a request for the IP parameters over the LAN network. o If a DHCP server responds (typically, the DHCP server resides in the Internet access router, such as the one at your home), the IPDACT configures and uses t he IP address, [...]

5/19/2008 15 of 15 Option “ g) IP Connectivity ” displays the IP settings that are running in the device. • If the IP Settings were not obtained through DHCP, the fixed ones entered in “ c) Quick Install ” are displayed, and actually used. If on the other hand, the IP Settings we re dynamically obtained from a DHCP server, these parameter[...]