Kraftware Corporation DS-32M2 инструкция обслуживания

1 This document explains the power , cooling, w eight, and rack placemen t requirements for the EMC departmental switch es listed below . It also describes the kits available for m ounting them in EMC and non- EMC racks and incl udes insta llation instruction s as well. Major s ection s are • Device Power , Cooling, and W eight Information ......[...]

2 EMC Depar tmen tal Switches DS-16M 2 and DS-32 M2 Installatio n Guide Device P ow er , Cooling, and W eight Inf ormation De vice P o w er , Co oling, and W eight Information De vice Di mensions De vice P lacement Re quirements The DS-16M2 switches must be located at the top of the rack/cabinet, because the power cor d routing for these switches r[...]

EMC Depar tm ental Switches DS-16M2 and DS -32M2 Install ation Guide 3 Switch Mounting Kit (DS-16M or DS-32M) Switch Mounting Kit (DS-1 6M or DS-32M) The DS1 6- and DS32- CRKH kits cont ain the 16- or 32-po rt st andar d swi tch rail moun ting k its, and the DS16 - and DS32 - CRKL kits cont ain t he 16- or 32-port low protru sion rai l mounting kit[...]

4 EMC Depar tmen tal Switches DS-16M 2 and DS-32 M2 Installatio n Guide Switch Mounting Kit (DS-16M or DS-32M) T oo ls Required f or Ins tallat ion Y ou will n eed to have the foll owing tool s available to com plete the installatio n of the rails an d switch(es). ◆ # 1 Phillip s head screwdriver ◆ 1/4-i n. nut driver ◆ 5/16-i n. nut drive r [...]

EMC Depar tm ental Switches DS-16M2 and DS -32M2 Install ation Guide 5 Installing the DS-16M and DS-32M Rails Installing the DS-16M and DS-32M Rails This secti on describes the install ation procedures for the D S-16M an d DS-32M ra ils. The fig ures bel ow show a fro nt and r ear view of four sets of rails ins talled in a 39U rack. Note that the r[...]

6 EMC Depar tmen tal Switches DS-16M 2 and DS-32 M2 Installatio n Guide Installing the DS-16M and DS-32M Ra ils DS-16M Rails Installatio n There are two dif f er ent length rails: The short rails range between 20.5 inches to 27 inches. The long rails range fr o m 27 inches to 34 inches. Each kit contains two diff er ent length r ear rail mounts. Us[...]

EMC Depar tm ental Switches DS-16M2 and DS -32M2 Install ation Guide 7 Installing the DS-16M and DS-32M Rails 1. Assemble the rails. The rails assembl y consis ts of an adjust able rai l, a C cha nnel, and two washers and kep nuts. See the figure below . a. Ins ert the t hread ed p ost s on th e C channel in to the slot on th e adjustable ra il. b.[...]

8 EMC Depar tmen tal Switches DS-16M 2 and DS-32 M2 Installatio n Guide Installing the DS-16M and DS-32M Ra ils 3. Adjust the length o f the rail to fit between the channels in the rack/cabinet. NOTE: The rail flanges go to the in side of the channels. 4. Once the rails ar e adjusted to the correct length, tighten the kep nuts on the rai l assembly[...]

EMC Depar tm ental Switches DS-16M2 and DS -32M2 Install ation Guide 9 Installing the DS-16M and DS-32M Rails M5 x 16 mm flat head screw s (see the table on page 3 ). Leave the screws finger-tight, and tighten them after the switch is installed. See the figur e below . If you ar e installing the switch in a 40U cabinet , install a key plate s pacer[...]

10 EMC Depar tmen tal Switches DS-16M 2 and DS-32 M2 Installatio n Guide Installing the DS-16M and DS-32M Ra ils 7. If you are installing the switch in a 39U cabinet, position t he #10 washer and ball stud in the center hole, between the two M5 x 12 mm screws. Hand- tighten the ball stu d. NOTE: The ball studs s upport th e bezel. If you are instal[...]

EMC Depar tm ental Switches DS-16M2 and DS -32M2 Install ation Guide 11 Installing the DS-16M and DS-32M Rails 9. Se cure t he rail t o a r ound-hol e r ear channel with 2 M5 x 12 mm pan-head scr ews (see the table on page 3), or secur e the rail to a sq u a re - ho l e re ar c h an n e l w i t h 2 s q u are - h o le w a s h er s an d M5 x 16 mm fl[...]

12 EMC Depar tmen tal Switches DS-16M 2 and DS-32 M2 Installatio n Guide Installing the DS-16M and DS-32M Ra ils DS-32M Rails Installatio n There are two dif ferent length rails: the short rails range fr om 20.5 inches to 27 inches. The long rails range fro m 27 inches to 34 inches. Each kit contains two differ ent length rear rail mounts. Use the [...]

EMC Depar tm ental Switches DS-16M2 and DS -32M2 Install ation Guide 13 Installing the DS-16M and DS-32M Rails Select the appropriate length rails, and follo w the steps below to install th em. 1. Assemble the rails. The rails assembl y consis ts of an adjust able rai l, a C cha nnel, and two washers and nuts. See the figure be low . a. Ins ert the[...]

14 EMC Depar tmen tal Switches DS-16M 2 and DS-32 M2 Installatio n Guide Installing the DS-16M and DS-32M Ra ils 3. Adjust the length o f the rail to fit between the channels in the rack/cabinet. NOTE: The rail flanges go to the in side of the channels. 4. Once the rails ar e adjusted to the correct length, tighten the kep nuts. NOTE: If the side s[...]

EMC Depar tm ental Switches DS-16M2 and DS -32M2 Install ation Guide 15 Installing the DS-16M and DS-32M Rails If you are installing the switch in a 40U cabinet , use the appr opriate screws to install the latch bracket (ins tead of the ball stud) to the outside edge of the channel a s you secure the rail. T o attach the bottom lat ch bracke t scre[...]

16 EMC Depar tmen tal Switches DS-16M 2 and DS-32 M2 Installatio n Guide Installing the DS-16M and DS-32M Ra ils 8. Secure the rail to a round-hole rear channe l with two M 5 x 12 mm scre ws (see the table on page 3), or secur e the rail to a square-h ole r ear channe l wi th two s quar e- hole wa shers an d M5 x 16 mm scre ws (see the table on pag[...]

EMC Depar tm ental Switches DS-16M2 and DS -32M2 Install ation Guide 17 Installing the DS-16M2 an d DS-32M2 Switches Installing the DS-16M2 and DS-32M2 Switc hes This section describes the pr ocedur es for installing the DS-16M2 an d DS-32M2 sw itches in a rack/cabin et, including attachin g the brackets on the switch. Both switches are installed i[...]

18 EMC Depar tmen tal Switches DS-16M 2 and DS-32 M2 Installatio n Guide Installing the DS-16M2 an d DS-32M2 Switches CAUTION ! The kits incl ude two (2) sets of screws. T o avoid d amaging the screw holes, be sure to check the labe ling on the bag s and use the appropriate se t of screws for your chassis. The chassi s product number is locat ed on[...]

EMC Depar tm ental Switches DS-16M2 and DS -32M2 Install ation Guide 19 Installing the DS-16M2 an d DS-32M2 Switches 5. Push the switch further into the rack/cabinet un til the hole in th e front part of each bracket (the “L”-sh aped end) aligns w ith the hole on the fixed rail. See the figure below . 6. T ighten the front screws securing the r[...]

20 EMC Depar tmen tal Switches DS-16M 2 and DS-32 M2 Installatio n Guide Installing the DS-16M2 an d DS-32M2 Switches 8. Install the bez el by positioni ng and insta lling the b ezel stud receptacles on the back of the bezel over the ball studs (39U rack) or latch brackets (40U rack) on the rail ends. 9. Push the bezel onto th e ball studs or latch[...]

EMC Depar tm ental Switches DS-16M2 and DS -32M2 Install ation Guide 21 Installing the DS-16M2 an d DS-32M2 Switches NOTE: There is a 3-inch space between the front of the switch and the back of the bezel. Thi s is enough room t o loop the co rd up with out pu shing th e bezel off. 12. Wh en installin g the DS-32M 2 switch, th e 2U spacing all ows [...]

22 EMC Depar tmen tal Switches DS-16M 2 and DS-32 M2 Installatio n Guide Installing the DS-16M2 an d DS-32M2 Switches CAUTION ! If you are removing the switche s from the cabi net, you mus t remove the to p switch fr om the back of the cabinet . Y ou can remove all switches be low the top switch from the front. 15. Attach the fibre-optic cables to [...]