Lincoln Electric UWW-170 инструкция обслуживания

SP 170-I and UWW - 170 OPERA TOR’S MANUAL IM591-B March, 2001 Safety Depends on You Lincoln arc welding and cutting equipment is designed and built with safety in mind. However, your overall safety can be increased by proper installation ... and thought- ful operation on your part. DO NOT INSTALL, OPERATE OR REPAIR THIS EQUIPMENT WITHOUT READING [...]

FOR ENGINE powered equipment. 1.a. Turn the engine off before troubleshooting and maintenance work unless the maintenance work requires it to be running. ____________________________________________________ 1.b. Operate engines in open, well-ventilated areas or vent the engine exhaust fumes outdoors. ________________________________________________[...]

ii SAFETY ii ARC RA YS can burn. 4.a. Use a shield with the proper filter and cover plates to protect your eyes from sparks and the rays of the arc when welding or observing open arc welding. Headshield and filter lens should conform to ANSI Z87. I standards. 4.b. Use suitable clothing made from durable flame-resistant material to protect your skin[...]

FOR ELECTRICALL Y powered equipment. 8.a. Turn off input power using the disconnect switch at the fuse box before working on the equipment. 8.b. Install equipment in accordance with the U.S. National Electrical Code, all local codes and the manufacturer ’ s recommendations. 8.c. Ground the equipment in accordance with the U.S. National Electrical[...]

iv SAFETY iv PR É CA UTIONS DE S Û RET É Pour votre propre protection lire et observer toutes les instructions et les pr é cautions de s û ret é specifiques qui parraissent dans ce manuel aussi bien que les pr é cautions de s û ret é g é n é rales suiv- antes: S û ret é Pour Soudage A L ’ Arc 1. Protegez-vous contre la secousse é le[...]

Thank You for selecting a QUALITY product by Lincoln Electric. We want you to take pride in operating this Lincoln Electric Company product ••• as much pride as we have in bringing this product to you! Read this Operators Manual completely before attempting to use this equipment. Save this manual and keep it handy for quick reference. Pay par[...]

vi vi T ABLE OF CONTENTS Page Installation .......................................................................................................Section A Technical Specifications ........................................................................................A-1 Identify and Locate Components ..............................................[...]

SP-170-I Duty Cycle Amps Volts at Rated Amperes 25% 125 20.25 60% 85 18.25 100% 70 17.50 Welding Current Range Maximum Open Circuit Voltage Wire Speed Range Rated DC Output: 30 – 170 amps 33 50-400IPM (1.3-10.2m/min) A-1 A-1 INST ALLA TION Fuse or Output Mode Input Voltage Breaker Size Input Amps Power Cord RATED 230V/50/60Hz 30 Super Lag 20 16 A[...]

A-2 A-2 INST ALLA TION Read entire installation section before starting installation. SAFETY PRECA UTIONS IDENTIFY AND LOCA TE COMPONENTS If you have not already done so, unpack the SP 170-I from its carton and remove all packing material around the SP 170-I. Remove the following loose items from the carton (see Figure A.1): 1. SP 170-I or UWW-170 [...]

A-3 A-3 INST ALLA TION SP 170-I SELECT SUIT ABLE LOCA TION The SP 170-I has an IP21S rating. Locate the welder in a dry location where there is free circulation of clean air into the louvers in the back and out the front of the unit. A location that minimizes the amount of smoke and dirt drawn into the rear louvers reduces the chance of dirt accumu[...]

A-4 A-4 INST ALLA TION W ork Cable Installation Refer to Figure A.2. 1. Open the wire feed section door on the right side of the SP 170-I. 2. Pass the end of the work cable that has the termi- nal lug with the smaller hole through the Work Cable Access Hole (1) in the case front. 3. Route the cable under the feedplate (6) and in front of the Wire F[...]

A-5 A-5 INST ALLA TION SP 170-I let and open the cylinder valve very slightly for an instant. This blows away any dust or dirt which may have accumulated in the valve outlet. BE SURE TO KEEP YOUR FACE AWAY FROM THE VALVE OUTLET WHEN “ CRACKING ” THE VALVE. Never stand directly in front of or behind the flow regulator when opening the cylinder v[...]

A-6 A-6 INST ALLA TION Line Cord Connection A 3 conductor international cordset with a 16 amp, 230 volt, two-prong plug is factory installed. Connect this plug to a mating grounded receptacle which is connected to an appropriate power supply per any applicable local codes. CONNECT TO A SYSTEM GROUNDING WIRE. SEE THE UNITED STATES NATIONAL ELECTRICA[...]

SP-170-I B-1 B-1 OPERA TION Read entire operation section before operating the SP 170-I. ELECTRIC SHOCK can kill. • Do not touch electrically live parts or electrode with skin or wet clothing. Insulate yourself from work and ground. • Always wear dry insulating gloves. FUMES AND GASES can be dangerous. • Keep your head out of fumes. • Use v[...]

B-2 B-2 OPERA TION ● No external shielding gas is required when used with Lincoln Innershield .035 ” (0,9 mm) NR ® -211- MP electrode. ● Spindle accommodates both 8 in. (200 mm) diame- ter and 4 in. (100 mm) diameter spools of wire. ● Accepts optional Spot/Stitch Timer Kit. WELDING CAP ABILITY The SP 170-I is rated at 125 amps, 20.25 volts[...]

B-3 B-3 OPERA TION WELDING OPERA TIONS SEQUENCE OF OPERA TION Wire Loading Refer to Figures B.2 and B.3. The machine power switch should be turned to the OFF ( “ O ” ) position before working inside the wire feed enclosure. The welder is shipped from the factory ready to feed 8" (200 mm) diameter spools with 2.2" (56 mm) maxi- mum wid[...]

B-4 B-4 OPERA TION Refer to Figure B.4 1 . Release the Spring Loaded Pressure Arm (1) rotate the Idle Roll Arm (2) away from the Wire Feed Drive Roll (3). Ensure that the groove size in the feeding position on the drive roll match - es the wire size being used. This occurs when the desired groove is located on the inside, toward the feedplate. See [...]

B-5 B-5 OPERA TION Making A Weld 1. See “ Process Guidelines ” in this section for selec- tion of welding wire and shielding gas and for range of metal thicknesses that can be welded. 2. See the Application chart on the inside of the wire feed compartment door for information on setting the SP 170-I controls. Refer to Table B.1 for alu- minum a[...]

B-6 SP 170-I B-6 OPERA TION The SP 170-I is suitable for .035" (0.9 mm) aluminum wire and .023" – .035" (0.6 - 0.9 mm) stainless wire. Refer to Table B.1 for recommended procedure set- tings. (Requires K499 Argon regulator kit and K664-1 Aluminum - Stainless Feeding Kit.) It is important when changing between welding with steel wir[...]

B-7 SP 170-I B-7 LEARNING T O WELD LEARNING T O WELD No one can learn to weld simply by reading about it. Skill comes only with practice. The following pages will help the inexperienced operator to understand weld- ing and develop this skill. For more detailed informa- tion, order a copy of “ New Lessons in Arc Welding ” listed at the end of th[...]

B-8 SP 170-I B-8 LEARNING T O WELD The “ arc stream ” is seen in the middle of the picture. This is the electric arc created by the electric current flowing through the space between the end of the wire electrode and the base metal. The temperature of this arc is about 6000 ° F, which is more than enough to melt metal. The arc is very bright, [...]

B-9 SP 170-I B-9 LEARNING T O WELD 2. Can I afford the extra expense, space, and lack of portability required for gas cylinders and gas sup- ply? 3. Do I require clean, finished-looking welds? If you have answered yes to all the above questions GMAW may be the process for you. If you have answered no to any of the above questions, then you should c[...]

B-10 SP 170-I B-10 LEARNING T O WELD FIGURE B.12 Penetration Unless a weld penetrates close to 100% of the metal thickness, a butt weld will be weaker than the material welded together. In the example shown in Figure B.13, the total weld is only half the thickness of the material thus the weld is only approximately half as strong as the metal. FIGU[...]

B-11 SP 170-I B-11 LEARNING T O WELD FIGURE B.16 Vertical-down Welding Refer to Figure B.17 Vertical-down welds are applied at a fast pace. These welds are therefore shallow and narrow and, as such, are excellent for sheet metal. Vertical-down welds may be applied to 5/32 ” (3.9 mm) and lighter material. Use stringer beads and tip the gun in the [...]

B-12 SP 170-I B-12 LEARNING T O WELD ARC RAYS can burn eyes and skin. When using an open arc process, it Is necessary to use correct eye, head and body protection. Protect yourself and others, read “ ARC RAYS can burn ” at the front of this manual. 2. The Correct Way To Strike An Arc 1. Be sure the work clamp makes good electrical contact to th[...]

B-13 SP 170-I B-13 LEARNING T O WELD Mild Steel 16 gauge or 1/16 inch (1.6 mm) Electrode 0.035" (0.9 mm) NR-211-MP Innershield Wire Voltage Setting “ V ” A Wire Feed Speed “ o|o ” 1.5 For the SP 170-I, use the following: Helpful Hints 1. For general welding, it is not necessary to weave the arc, neither forward or backward nor sideways[...]

B-14 SP-170-I B-14 LEARNING T O WELD MA CHINE SET UP FOR THE GMA W (MIG) PROCESS 1. See PROCESS GUIDELINES in the OPERATION section for selection of welding wire and shielding gas, and for range of metal thicknesses that can be welded. 2. See the Application Guide on the inside of wire feed section door for information on setting the controls. 3. S[...]

Helpful Hints 1. For general welding, it is not necessary to weave the arc, neither forward or backward nor sideways. Weld along at a steady pace. You will find it easier. 2. When welding on thin plate, you will find that you will have to increase the welding speed, whereas when welding on heavy plate, it is necessary to go more slowly in order to [...]

B-16 SP 170-I B-16 LEARNING T O WELD 4. After you strike the arc, practice the correct electri- cal stickout. Learn to distinguish it by its sound. 5. When you are sure that you can hold the correct electrical stickout, with a smooth “ crackling ” arc, start moving. Look at the molten puddle constantly, 6. Run beads on a flat plate. Run them pa[...]

B-17 SP 170-I B-17 LEARNING T O WELD Proper Gun Handling Most feeding problems are caused by improper han- dling of the gun cable or electrodes. 1. Do not kink or pull the gun around sharp corners 2. Keep the gun cable as straight as practical when welding. 3. Do not allow dolly wheels or trucks to run over the cables. 4. Keep the cable clean. 5. I[...]

Be sure to read and understand the warnings on this welding machine and the section on ARC WELDING SAFETY PRECAUTIONS in the Operating Manual. Because design, fabrication, assembly and welding variables affect the results obtained in applying this type of information, the serviceability of a product or assembly is the responsibility of the builder/[...]

C-1 C-1 A CCESSORIES OPTIONAL A CCESSORIES See Maintenance section for instructions on installing drive roll, cable liner, contact tip and their proper configuration. 1. KP665-045C Drive Roll – Optional — Knurled drive roll for feeding .035 - .045 ” (0.9 - 1.2 mm) diameter flux-cored electrode. 2. K695-1 Spot / Stitch Timer Kit — Includes s[...]

C-2 C-2 A CCESSORIES INNERSHIELD (FCA W) CONVERSION Several changes are needed to convert the unit for operation with the Innershield (FCAW) process. The following conversions should be reviewed before welding with (FCAW): 1. Change the output polarity to DC( – ). See “ Work Cable Installation ” in Installation section for details. 2. Install[...]

MAINTENANCE SAFETY PRECA UTIONS ELECTRIC SHOCK can kill. • Disconnect input power by removing plug from receptacle before working inside SP170-I. Use only grounded receptacle. Do not touch electrically “ hot ” parts inside SP 170-I. • Have qualified personnel do the mainte- nance and trouble shooting work. R OUTINE MAINTENANCE PO WER SOURCE[...]

D-2 SP-170-I D-2 MAINTENANCE GUN AND CABLE MAINTENANCE Gun Cable Cleaning Clean cable liner after using approximately 300 lbs (136 kg) of solid wire or 50 lbs (23 kg) of flux-cored wire. Remove the cable from the wire feeder and lay it out straight on the floor. Remove the contact tip from the gun. Using low pressure air, gently blow out the cable [...]

D-3 D-3 MAINTENANCE SP 170-I COMPONENT REPLA CEMENT PR OCEDURES CHANGING THE CONT A CT TIP (These instructions pertain to the Lincoln Electric ® gun having a black trigger. The instructions for the Magnum ™ 100L gun, having a red trigger, are similar except that the gas nozzle and contact tip are both threaded.) 1. Refer to Figure D.2a or D.2b. [...]

D-4 D-4 MAINTENANCE SP 170-I CHANGING LINER NOTICE: The variation in cable lengths pre- vents the interchangeability of liners. Once a liner has been cut for a particular gun, it should not be installed in another gun unless it can meet the liner cutoff length require- ment. Refer to Figure D.2a or D.2b. 1 . Remove the gas nozzle from the gun (thre[...]

D-5 D-5 MAINTENANCE SP 170-I GUN HANDLE P ARTS (b lack trig ger) The gun handle consists of two halves that are held together with a C-clip (located at the cable end of the gun). To open up the gun handle assembly, remove the C-clip and pry down the trigger handle half with a screwdriver. See Figure D.3. FIGURE D.3 Screwdriver C-clip Cable GUN HAND[...]

E-1 E-1 TR OUBLESHOO TING SP 170-I This Troubleshooting Guide is provided to help you locate and repair possible machine malfunctions. Simply follow the three-step procedure listed below. Step 1. LOCATE PROBLEM (SYMPTOM). Look under the column labeled “ PROBLEM (SYMP- TOMS) ” . This column describes possible symptoms that the machine may exhibi[...]

E-2 E-2 TR OUBLESHOO TING SP 170-I Observe Safety Guidelines detailed in the beginning of this manual. PROBLEMS (SYMPT OMS) Major physical or electrical damage is evident. No wire feed, weld output or gas flow when gun trigger is pulled. Fan does NOT operate. No wire feed, weld output or gas flow when gun trigger is pulled Fan operates normally. PO[...]

E-3 E-3 TR OUBLESHOO TING SP 170-I PROBLEMS (SYMPT OMS) No wire feed when gun trigger is pulled. Fan runs, gas flows and machine has correct open circuit voltage (33 VDC maximum) – weld output. POSSIBLE AREAS OF MISADJUSTMENT(S) 1. If the wire drive motor is running make sure that the correct drive rolls are installed in the machine. 2. Check for[...]

E-4 SP-170-I E-4 TR OUBLESHOO TING If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your LOCAL AUTHORIZED LINCOLN ELECTRIC FIELD SERVICE FACILITY for assistance before you proceed. CA UTION PROBLEMS (SYMPT OMS) Arc is unstable – Poor starting POSSIBLE AREAS OF MISADJUSTMENT(S) [...]

SP-170-I F-1 F-1 WIRING DIA GRAMS WIRING DIA GRAM: NOTE: This diagram is for reference only. It may not be accurate for all machines covered by this manual. The specific diagram for a particular code is pasted inside the machine on one of the enclosure panels.[...]

NO TES SP 170-I[...]

Now A vailable...12th Edition The Procedure Handbook of Ar c W elding With over 500,000 copies of previous editions published since 1933, the Procedure Handbook is considered by many to be the “ Bible ” of the arc welding industry. This printing will go fast so don ’ t delay. Place your order now using the coupon below. The hardbound book con[...]

W ARNING A VISO DE PRECA UCION A TTENTION W ARNUNG A TEN ÇÃ O Spanish French German Portuguese Japanese Chinese Korean Arabic READ AND UNDERST AND THE MANUF ACTURER’S INSTRUCTION FOR THIS EQUIPMENT AND THE CONSUMABLES TO BE USED AND FOLLOW YOUR EMPLOYER’S SAFETY PRACTICES. SE RECOMIENDA LEER Y ENTENDER LAS INSTRUCCIONES DEL F ABRICANTE P ARA [...]

W ARNING A VISO DE PRECA UCION A TTENTION W ARNUNG A TEN ÇÃ O Spanish French German Portuguese Japanese Chinese Korean Arabic LEIA E COMPREENDA AS INSTRUÇÕES DO F ABRICANTE P ARA ESTE EQUIP AMENTO E AS P ARTES DE USO, E SIGA AS PRÁTICAS DE SEGURANÇA DO EMPREGADOR. ● Keep your head out of fumes. ● Use ventilation or exhaust to remove fumes[...]

• Sales and Service through Subsidiaries and Distributors Worldwide • Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.lincolnelectric.com • World's Leader in Welding and Cutting Products •[...]