Marquis SERIES инструкция обслуживания

• M ARQUIS /C OUNTESS S ERIES • • C EILING F AN O WNER ’ S M ANUAL • W ARNING: Read and follow these instructions carefully and be mindful of all warnings shown thr oughout. 5/04[...]

G ENERAL I NST ALLA TION & O PERA TION I NSTRUCTIONS I MPOR T ANT S AFEGUARDS : 1. To ensure the success of the installation, be sure to read the instructions and review the diagrams thor oughly before beginning . 2. To avoid possible electric shock, be sure electricity is turned off at the main power box before wiring . All electrical connecti[...]

Wa r n ings: • Disconnect power by removing fuse or turning off circuit breaker befor e installing the fan and/or optional lighting. Support dir ectly from building structur e. •T o reduce the risk of fir e, electric shock, or personal injury , mount to outlet box marked “ acceptable for fan support ” and use mounting screws pr ovided with [...]

1. Unpack your fan and check the contents. Do not discard the car ton. If warranty replacement or r epair is ever necessar y , the fan should be returned in original packing. Remove all par ts and hardwar e. Do not lay motor housing on its side, or the decorative housing may shift, be bent or damaged. 2. Examine all parts. Y ou should have the foll[...]

P REP ARA TION : Ve rify you have all parts before beginning the installation. Check foam insert closely for missing par ts. Remove motor from packing. T o avoid damage to finish, assemble motor on soft padded surface or use the original foam inset in motor box. Do not lay motor housing on its side as this could r esult in shifting of motor in deco[...]

I NST ALLING T HE F AN 5 This fan ha s two installati on options: I NST ALLA TION : The HUGGER method is preferr ed if maximum headroom is r equired. The ceiling must be horizontal, not sloped. Blades will be approximately 8˝ fr om the ceiling. Air flow will be reduced when the fan is installed using the HUGGER method. The DOWNROD MOUNTING method [...]

6 I NST ALLING T HE F AN – H UGGER STYLE I NST ALLA TION O PTION #1: H UGGER STYLE MOUNTING 1. Remove the plastic trim ring from the canopy to expose the 6 mounting holes. The downr od, ball, cotter pin, and collar cover will not be used for this mounting (Fig. 1). 2. Feed fan wires thr ough the canopy and position the canopy over the mounting co[...]

1. Carefully support fan body (motor) in its styr ofoam packing with the mounting collar (where the wir es come out) facing upward. 2. Remove ball from downr od by loosening set screw in the side of the ball. Slide ball down and r emove ball pin; re move ball. 3. Feed the wires fr om top of fan through end of downr od and set end of downrod into mo[...]

1. Lift ball/downrod/fan into hanger bracket opening. NOTE: The tab opposite hanger bracket opening should fit in slot on ball. 2. Make wire connections, (r efer to section titled “Electrical Connections”). 3. Slide canopy up and fasten to hanger bracket with 4 screws pr ovided. 8 I NST ALLING THE F AN – D OWNROD STYLE I NST ALLA TION O PTION[...]

E LECTRICAL C ONNECTIONS : Be sure electricity is turned off at the main power box befor e wiring E LECTRICAL C ONNECTIONS 9 Wiring box Light Switch BLK BLUE WH F an controlled by pull chain on fan. Light controlled by wa ll switch. Ground to mounting brack et BLUE BLK WH WH Fa n Light Po w e r lines 120V G R O U N D BLK WH GREEN F an controlled by[...]

10 B LADE A TT ACHMENT B LADE A TT ACHMENT : Blade to motor screw and metal lock w asher Blade assembly Fig. 2 1. Place fiber washer on scr ew . Insert this assembly thr ough the blade and start the scr ew into the blade arm. Repeat this procedur e without tightening the screw until all 3 scr ews have been started into the blade arm (Fig. 1). NOTE:[...]

11 Side Screw (x3) Switch Housing Connector (plug) with Side Buckle Switch Housing Hub (bottom of motor) Key hole Slot (x3) Connector (receptacle) Pull Chain Re verse Switch Opening f or Re verse Switch Optional Light Kit screws into bottom of Switch Housing I NST ALLA TION OF R EMOV ABLE S WITCH H OUSING NOTE: Be sure the power is of f before inst[...]

12 O PERA TION 5/04 Regency Ceiling Fans Tu rn on the power and check operation of the fan. The fan is controlled by the use of the fan speed pull chain as follows: one pull = high speed two pulls = medium speed three pulls = low speed four pulls = off For proper functions, ensur e that the fan speed pull chain is pulled down fully and released eac[...]

2/01 Regency Ceiling Fans T HANK YOU FOR PURCHASING A R EGENCY C EILING F AN . Wr ite to us at: Regency Ceiling Fans P. O. Box 730 Fenton, MO 63026 V isit us on the W eb at: www .regencyfan.com Periodic cleaning of your new ceiling fan is about the only maintenance that is needed. Only use a soft brush or lint free cloth to avoid scratching the fin[...]