NAPCO Alert 800 инструкция обслуживания

OPERATING GUIDE FOR YOUR MAGNUM ALEm-800/800s SECURITY SYmM 01955 NAPCO[...]

You have taken a major step in protecting your home or busi- ness by having a Napco Magnum Alert-800/800S Alarm Control Center installed. Please read this guide thor- oughly to familiarize yourself with your new security system. Keep this booklet handy for future reference. Note especially the ALARM PLAN on page 15. Your alarm specialist will help [...]

A delay period that allows the system to be reset before it reports to a cantml station. AlmmPlmn Identifies the areas of tected by each zone o r our premises pro- protection and lists zone features (see page 15). Anrrkrg/- Turning yours tern ON or OFF. This can be done by en enng a code on the D r”. it- Ke ‘R keypad, or by turning an optional [...]

lndlcator ughts -/-n=Y wm 1-1 l Steady - system is armed. l Flashes - system is in alarm. Count the number of flashes to tell in which zone the alarm occurred. Example: Fourflashes- alarm in Zone 4. smU9Mf-l l Steady - system is disarmed, all zones okay. l Flashes - zone in trouble (in- capable of being armed). Count the number of flashes to deter-[...]

Each security system is custom tailored to the owner’s needs, but all MAGNUM ALERTBOO/ 800s have the following: 1. zones 2.lhdMg~KayKeypad f.TheAIammOutput Your system contains up to six f=Wkay_J When any zone is activated, separate zones. Each zone is an independent circuit that pro- Lets you perform the following the Contr?l Center responds fun[...]

uslrBgyourcdetoaml addiurmtheqs8mm If your system includes the Once you enter your personal Napco Digit-Key keypad you can code into the Napco Digit-Key choose your own private code keypad, the red ARMED/MEMORY to arm and disarm the Control light will go on to show the Control Center. To program your code, Center is armed, and off to show slide the[...]

First, check the green STATUS light at the keypad or keyswitch. If this light is on stead- ily, enter your code. The red ARMED/MEMORY light will come on and the green lamp will go out. Leave immediately through the entry/exit doorway before the delay time runs out. If you delay too long in leaving the premises, you will hear the Mini-Sounder warn y[...]

SHUNT button, labeled “S”, and enter your code. The yellow SHUNT light and the red ARMED/ MEMORY light will come on. The green light will be out. All zones programmed by your alarm spe- cialist to respond to manual shunting will be shunted (even if some are not in “trouble”). Leave quickly when the red ARMED/MEMORY light goes on. Be sure to[...]

Arming with zone shunting You might have chosen one or two zones that you can man- ually “shunt out” of the system from the keypad. A shunted (bypassed) zone cannot cause an alarm. Zone shunting may be used for turning off interior protection, or allowing you to turn on only your perimeter protection. To arm with zone(s) shunted, first check th[...]

Panic alarm To activate a panic alarm and call for outside help, press the two buttons marked l and # on the Digit-Key keypad. Makesure you press both buttons at the s8me time. The panic zone is capable of sending asilent signal to the Central Station when a Digital Communicator is being used (optional). The Penic Ai8rm is always active, whether yo[...]

Your Alarm Specialist may have programmed your security system to be monitored by a Central Station. The built-in digital communicator can trans- mit emergency signals to the Centml Station 24 hours a day.[...]

AbortDeby Note which zones on your Cantfal Madon alarm plan have abort delay. This mribwk is a 16 second delay that enables The Central Station will ac- An optional feature that per- you to reset the system before a knowledge the fact that you have mits the Central Station to receive zone condition report is sent to armed your system by “ringing [...]

The following information is applicable only where local ordinance permits use of your alarm Control Center for fire detection Controrlklg Your Fin Circuit If your alarm specialist installed smoke detectors or heat sensing thermostats, you have 24 hour fire protection. This optional Fire Pro- tection Zone is always active, even though your system m[...]

an escape plan Even with the most advanced fire alarm system, adequate pro- tection requires an escape plan. To prepare your plan: Draw floorplans of your build- ing (see sample). Show two exits: a front or back door and a window from each room. (Make sure the window works. You may need a special fire escape ladder if the window is high up.) Write [...]

Zone Area Protected Zone Features Contacts (doors, windows, etc.) 1 3 I 4 I Aux. (6) Central Station? Service Person ‘optlonal katun, Telephone# , Telephone# 15[...]

NAPCOLlMiTEDWARRANly[...]