Newland NLS-HR1250-90 инструкция обслуживания

HR1250-70 HR1250-90 Hand-held Barcode Scanner User Guide[...]

Disclaimer © 2014 Fujian Newland Auto-ID T ech. Co., Ltd. All rights reserved. Please read through the manual carefully before using the product and operate it according to the manual. It is advised that you should keep this manual for future reference. Do not disassemble the device or re move the seal label from the devic e. Otherwise, Fujian New[...]

Revision History V ersion Description Date V1.0 Initial release. May 9, 2014[...]

Table of Contents Revision Hi story .............................................................................................................. .......................... - 3 -  Preface ....................................................................................................................... .................................... 1[...]

Command T rigger Mode ...................................................................... Error! Book mark not defined.  Security Level ................................................................................................................ .......................... 50  Good Read Beep ..............................................[...]

Custom Suffi x ................................................................................................................. ......................... 76  Enable/Disable Cu stom Suffix .................................................................................................. ......... 76  Set Custom Suf fix .......................[...]

Restore Factor y Defaults ...................................................................................................... ............ 93  Enable/Disable ISSN ......................................................................................................................... 93  ISBN ...............................................[...]

Enable/Disable Deutsc he 12 .................................................................................................... ........1 10  Matrix 2 of 5 (Europ ean Matrix 2 of 5) ........................................................................................ ............ 1 1 1  Restore Factor y Defaults ..........................[...]

Check Digit V e rifica tion ...................................................................................................... ............. 132  Set Length Range fo r Code 1 1 .................................................................................................. ...... 133  Plessey ............................................[...]

[...]

1 Preface Introduction This manual provides detailed in structions for setting up and usi ng the HR1250-70/HR1250-90 hand- held barcode scanner (hereinafter referred to as “HR12 scanner” or “the scanner” ). Chapter Description  Chapter 1, Getting Started : This chapter gives a general description of HR12 scanner including its technical p[...]

2 Chapter 1 Getting Started Introduction HR12 scanner is a 1D barcode scanner with excell ent performance. Based on the technology independently developed by Newlan d, HR12 scanner is able to deliver rapid image acquisition and accurate decoding; it can provide customers with best services. HR12 scanner boasts the ergonomical design that ensures ea[...]

3 Connect HR12 to a Host HR12 scanner must be connected to a host device in actual application, such as PC, POS or any intelligent terminal with USB interface. Fig. 1-2[...]

4 Power on, Power off, Sleep, Reboot Power on the scanner Connect the scanner to a hos t device. Then the scanner will be turned on and automatica lly go into sleep mode. Power off the scanner Disconnect the scanner from the host. Enter the sleep mode If no operation is performed on the scanner for some time, the scanner will automatically enter th[...]

5 Dimensions (unit: mm) Left View Fig. 1-3 Front View Fig. 1-4 Top View Fig. 1-5[...]

6 Scanning Instructions When the HR12 scanner is in the Manual mode (def ault), you can follow the steps below to scan a barcode: 1. Hold down the trigger. Then the sc anner will project a red aiming beam. 2. Aim the red beam across the center of barcode, as shown in Fig.1-6. 3. Release the trigger when t he red beam goes off. For a successful read[...]

7 Scan Angle The scanner is designed to function within a certain range of scan angles. Any unreasonable devia tion may cause decoding failure. Scan angles of the scanner:  Pitch : ±60°, 0° Roll and 0° Skew (Fig. 1-7)  Roll : ±30°, 0° Pitch and 0° Skew (Fig. 1-8)  Skew: ±60°, 0° Roll and 0° Pitch (Fig. 1-9) Fig. 1-7 Fig. 1-8 Fi[...]

** Enter Setup Exit Setup 8 Chapter 2 System Settings Introduction There are two ways to configure the scanner : barcode program ming and command programming. Barcode Programming The scanner can be configured by scannin g programming barcodes. All user pro grammable features/options are described along with their programming barc odes/commands in t[...]

** Enter Setup 9 Exit Setup Read Register The read register command is used to read the content s of 1 to 256 contiguous registers in the scanner. Syntax: {Prefix1} {Types} {Lens} {Address} {Datas} {FCS} Prefix1 : 0x7E 0x00 (2 bytes) Types : 0x07 (1 byte) Lens : 0x01 (1 byte). Address: 0x0000~0xFFFF (2 bytes), starting register address. Datas : 0x0[...]

** Enter Setup Exit Setup 1 0 Reply: {Prefix2} {Types} {Lens} {Datas} {FCS} 1) Success message: Prefix2 : 0x02 0x00 Types : 0x00 (success) Lens : Byte count of Datas returne d . If Lens=0x00, that means values of 256 contiguous registers are returned. Datas : 0x00~0xFF, data that are returned . FCS : CRC-CCITT checksum. 2) FCS error message: Prefix[...]

** Enter Setup 1 1 Exit Setup Example: Read the contents (0x35, 0x36, 0x37) of 3 conti guous registers starting from register 0x0005. 1) Read operation succeeds: Command sent: 0x7e 0x00 0x07 0x01 0x00 0x05 0x03 0xd e 0xf6 Message received: 0x02 0x00 0x00 0x03 0x35 0x 36 0x37 0x2a 0xba 2) Incorrect FCS: Command sent: 0x7e 0x00 0x07 0x01 0x00 0x05 0x[...]

** Enter Setup Exit Setup 1 2 Write Register The write register command is used to write conti guous registers (1 to 256 registers) in the scanner. Syntax: {Prefix1} {Types} {Lens} {Address} {Datas} {FCS} Prefix1 : 0x7E 0x00 (2 bytes) Types : 0x08 (1 byte) Lens : 0x00~0xFF (1 byte), byte coun t, i.e. number of registers written. When Lens=0x00, 256[...]

** Enter Setup 1 3 Exit Setup Reply: {Prefix2} {Types} {Lens} {Datas} {FCS} 1) Success message: Prefix2 : 0x02 0x00 Types : 0x00 (success) Lens : 0x01 Datas : 0x00 FCS : 0x33 0x31 (CRC -CCITT checksum) 2) FCS error message: Prefix2 : 0x02 0x00 Types : 0x01 (incorrect FCS) Lens : 0x01 Datas : 0x00 FCS : 0x04 0x01 (CRC-CCITT checksum) 3) Invalid comm[...]

** Enter Setup Exit Setup 1 4 Example: Write 0x31, 0x32, 0x33, 0x34 into 4 contiguous registers starting from register 0x000a. 1) Write operation succeeds: Command sent: 0x7e 0x00 0x08 0x04 0x00 0x26 0x31 0x3 2 0x33 0x34 0xcd 0xa4 Message received: 0x02 0x00 0x00 0x01 0x00 0x 33 0x31 2) Incorrect FCS: Command sent: 0x7e 0x00 0x08 0x04 0x00 0x26 0x3[...]

** Enter Setup 1 5 Exit Setup Enable/Disable EEPROM Write By default, EEPROM write is disabled after the devic e is powered up. You need to enable it before a write operation and recommendedly disable it afterwards to prevent miswriting. Syntax: {Prefix1} {Types} {Lens} {Address} {Datas} {FCS} Prefix1 : 0x7E 0x00 Types : 0x03 (EEPROM writ e enable)[...]

** Enter Setup Exit Setup 1 6 Reply: {Prefix2} {Types} {Lens} {Datas} {FCS} 1) Success message: Prefix2 : 0x02 0x00 Types : 0x00 (success) Lens : 0x01 Datas : 0x00 FCS : 0x33 0x31 (CRC -CCITT checksum) 2) FCS error message: Prefix2 : 0x02 0x00 Types : 0x01 (incorrect FCS) Lens : 0x01 Datas : 0x00 FCS : 0x04 0x01 (CRC-CCITT checksum) 3) Invalid comm[...]

** Enter Setup 1 7 Exit Setup Write EEPROM The scanner has 512 bytes of EEPROM. The EEPROM write command is used to write data to up to 256 addresses. You need to enable EEPROM write before a write operation and re commendedly disable it afterwards to prevent miswriting. Note that writi ng without enabling it first will not return any error message[...]

** Enter Setup Exit Setup 1 8 Reply: {Prefix2} {Types} {Lens} {Datas} {FCS} 1) Success message: Prefix2 : 0x02 0x00 Types : 0x00 (success) Lens : 0x01 Datas : 0x00 FCS : 0x33 0x31 (CRC -CCITT checksum) 2) FCS error message: Prefix2 : 0x02 0x00 Types : 0x01 (incorrect FCS) Lens : 0x01 Datas : 0x00 FCS : 0x04 0x01 (CRC-CCITT checksum) 3) EERPOM not r[...]

** Enter Setup 1 9 Exit Setup Example: Write 0x51, 0x52, 0x53, 0x54 into 4 conti guous addresses starting from address 0x0000. 1) Write operation succeeds: Command sent: 0x7e 0x00 0x04 0x04 0x00 0x00 0x51 0x5 2 0x53 0x54 0xbc 0x17 Message received: 0x02 0x00 0x00 0x01 0x00 0x 33 0x31 2) Incorrect FCS: Command sent: 0x7e 0x00 0x04 0x03 0x00 0x00 0x5[...]

** Enter Setup Exit Setup 2 0 Read EEPROM The scanner has 512 bytes of EEPROM . The EEPROM rea d command is used to read the contents from 1 to 256 contiguous addre sses of the EEPROM. Syntax: {Prefix1} {Types} {Lens} {Address} {Datas} {FCS} Prefix1 : 0x7E 0x00 Types : 0x05 Lens : 0x01 Address: 0x0000~0xFFFF (2 by tes), starting EEPROM address to r[...]

** Enter Setup 2 1 Exit Setup Reply: {Prefix2} {Types} {Lens} {Datas} {FCS} 1) Success message: Prefix2 : 0x02 0x00 Types : 0x00 (success) Lens : Byte count of Datas returned. Datas : 0x00~0xFF, data that are returned . FCS : CRC-CCITT checksum. 2) FCS error message: Prefix2 : 0x02 0x00 Types : 0x01 (incorrect FCS) Lens : 0x01 Datas : 0x00 FCS : 0x[...]

** Enter Setup Exit Setup 2 2 Example: Read the contents (0x35 0x36 0x37) of 3 contiguous EEPROM addresses starting from address 0x0005. 1) Read operation succeeds: Command sent: 0x7e 0x00 0x05 0x01 0x00 0x05 0x0 3 0x9a 0x75 Message received: 0x02 0x00 0x00 0x03 0x35 0x 36 0x37 0x2a 0xba 2) Incorrect FCS: Command sent: 0x7e 0x00 0x05 0x01 0x00 0x05[...]

** Enter Setup 2 3 Exit Setup Registers Register 0x0000 Bit Feature Bit 7 Reserved Bit 6 1: Silent Mode Off 0: Silent Mode On Bit 5-4 Reserved Bit 3-2 Illumination: 00: Off 01: On When Scanning 10/1 1: Always On Bit 1-0 Scan Mode: 00: Manual Mode 01: Command T rigger Mod e 10: Continuous Mode 1 1: Sense Mode Register 0x0003 Bit Feature Bit 7-0 Sens[...]

** Enter Setup Exit Setup 2 4 Register 0x0009 Bit Feature Bit 7-2 Reserved Bit 1-0 00: USB DA T APIPE 01: USB HID-KBW 10: USB COM Port Emulation 1 1: USB HID-POS Register 0x000A Bit Feature Bit 7-5 Reserved Bit 4 0: Allow Rereading Same Barcode 1: Disallow Rereading Same Barcode Bit 3-2 Reserved Bit 1-0 Security Level 00-03: 0-3 level. The higher t[...]

** Enter Setup 2 5 Exit Setup Register 0x0019 Bit Feature Bit 7-0 USB Country Keyboard T ypes 0 0 : U . S . 0 1 : B e l g i u m 0 2 : B r a z i l 03: Canada 04: Czech 05: Denmark 06: Finland 07: France 08: Austria 09: Greece 0A: Hungary 0B: Israel 0C: Italy 0D: Latin America 0E: Netherland 0F: Norway 10: Poland 1 1: Portugal 12: Romania 13: Russia [...]

** Enter Setup Exit Setup 2 6 Register 0x0037-0x33 Bit Feature Bit 39-0 Set Custom Prefix Register 0x0042-0x3E Bit Feature Bit 39-0 Set Custom Suffix Register 0x004D-0x49 Bit Feature Bit 39-0 Set T erminating Character Suffix Register 0x0061 Bit Feature Bit 7-1 Reserved Bit 0 1: Enable Co de 128 0: Disable Code 128 Register 0x0062 Bit Feature Bit 7[...]

** Enter Setup 2 7 Exit Setup Register 0x0066 Bit Feature Bit 7-6 Reserved Bit 5 1: Enable EAN-13 5-digit Add-on Code 0: Disable EAN-13 5-digit Add-on Code Bit 4 1: Enable EAN-13 2-digit Add-on Code 0: Disable EAN-13 2-digit Add-on Code Bit 3 1: EAN-13 Add-on Cod e Required 0: EAN-13 Add-on Code Not Required Bit 2 1: T ransmit EAN-13 Check Digit 0:[...]

** Enter Setup Exit Setup 2 8 Register 0x006A Bit Feature Bit 7-6 Reserved Bit 5-4 UPC-E System Character 01: Do not transmit system character 10/1 1: T ransmit system character Bit 3-2 Reserved Bit 1-0 UPC-A Preamble Character 00: No Preamble 01: System Charac ter 10/1 1: System Character & Country Code Register 0x006B Bit Feature Bit 7 Reserv[...]

** Enter Setup 2 9 Exit Setup Register 0x006E Bit Feature Bit 7-4 Reserved Bit 3 1: T ransmit ITF-14 Check Digit 0: Do Not T ransmit ITF-14 Check Digit Bit 2 Reserved Bit 1-0 00: Disable ITF-14 01: Decode as Interleaved 2 of 5 10/1 1: Enable ITF-14 Register 0x006F Bit Feature Bit 7-4 Reserved Bit 3 1: T ransmit Deutsche 14 Check Digit 0: Do Not T r[...]

** Enter Setup Exit Setup 3 0 Register 0x0073 Bit Feature Bit 7-4 Reserved Bit 3 1: T ransmit Standard 25 Check Digit 0: Do Not T ransmit Standard 25 Check Digit Bit 2 1: Enable Standard 25 Check Digit 0: Disable Standard 25 Check Digit Bit 1 Reserved Bit 0 1: Enable Standard 25 0: Disable Standard 25 Register 0x0074 Bit Feature Bit 7-6 Reserved Bi[...]

** Enter Setup 3 1 Exit Setup Register 0x0076 Bit Feature Bit 7-4 Reserved Bit 3 1: T ransmit Code 93 Check Digit 0: Do Not T ransmit Code 93 Check Digit Bit 2 1: Enable Code 93 Check Digit 0: Disable Code 93 C heck Digit Bit 1 Reserved Bit 0 1: Enable Code 93 0: Disable Code 93 Register 0x0077 Bit Feature Bit 7-6 Reserved Bit 5 1: T ransmit Code 1[...]

** Enter Setup Exit Setup 3 2 Register 0x0079 Bit Feature Bit 7-5 Reserved Bit 4 1: T ransmit MSI-Plessey Check Digit 0: Do Not T ransmit MSI-Plessey Check Digit Bit 3-2 MSI-Plessey Check Digit V erification: 00: Disable 01: One Check Digit, MOD10 10: T wo Check Digits, MOD10/MOD10 1 1: T wo Che ck Digits, MOD10/MOD1 1 Bit 1 Reserved Bit 0 1: Enabl[...]

** Enter Setup 3 3 Exit Setup Register 0x0080 Bit Feature Bit 7-0 Set Code 128 Maximum Length Register 0x0081 Bit Feature Bit 7-0 Set Code 128 Minimum Length Register 0x0082 Bit Feature Bit 7-0 Set UCC/EAN-128 Maximum Length Register 0x0083 Bit Feature Bit 7-0 Set UCC/EAN-128 Minimum Length Register 0x0084 Bit Feature Bit 7-0 Set AIM 128 Maximum Le[...]

** Enter Setup Exit Setup 3 4 Register 0x008A Bit Feature Bit 7-0 Set Industrial 25 Maximum Length Register 0x008B Bit Feature Bit 7-0 Set Industrial 25 Minimum Length Register 0x008C Bit Feature Bit 7-0 Set Standard 25 Maximum Length Register 0x008D Bit Feature Bit 7-0 Set Standard 25 Minimum Length Register 0x008E Bit Feature Bit 7-0 Set Code 39 [...]

** Enter Setup 3 5 Exit Setup Register 0x0094 Bit Feature Bit 7-0 Set Code 1 1 Maximum Length Register 0x0095 Bit Feature Bit 7-0 Set Code 1 1 Minimum Length Register 0x0096 Bit Feature Bit 7-0 Set Plessey Maximum Length Register 0x0097 Bit Feature Bit 7-0 Set Plessey Minimum Length Register 0x0098 Bit Feature Bit 7-0 Set MSI-Plessey Maximum Length[...]

** Enter Setup Exit Setup 3 6 Register 0x00A9, 0x00A8 Bit Feature Bit 15-0 Set EAN-8 Code ID ASCII value of one or two English letters (lower or upper case) Register 0x00AB, 0x00AA Bit Feature Bit 15-0 Set EAN-13 Code ID ASCII value of one or two English letters (lower or upper case) Register 0x00AD, 0x00AC Bit Feature Bit 15-0 Set ISSN Code ID ASC[...]

** Enter Setup 3 7 Exit Setup Register 0x00B9, 0x00B8 Bit Feature Bit 15-0 Set ITF-14 Code ID ASCII value of one or two English letters (lower or upper case) Register 0x00BB, 0x00BA Bit Feature Bit 15-0 Set Deutsche 14 Code ID ASCII value of one or two English letters (lower or upper case) Register 0x00BD, 0x00BC Bit Feature Bit 15-0 Set Deutsche 1[...]

** Enter Setup Exit Setup 3 8 Register 0x00C7, 0x00C6 Bit Feature Bit 15-0 Set Codabar Code ID ASCII value of one or two English letters (lower or upper case) Register 0x00C9, 0x00C8 Bit Feature Bit 15-0 Set Code 93 Code ID ASCII value of one or two English letters (lower or upper case) Register 0x00CB, 0x00CA Bit Feature Bit 15-0 Set Code 1 1 Code[...]

** Enter Setup 3 9 Exit Setup Enable/Disable Barcode Programming Scanning the Enter Setup / Exit Setup barcode can enable/disable barcode programming. After barcode programming is enabled, you can scan a number of programming barcodes to configure your scanner. Barcode programming is on by default. In real applic ation, programming barcodes ha rdly[...]

** Enter Setup Exit Setup 4 0 Factory Defaults Scanning the following barcode can restore the scanner to the factory defaults. Y ou may need to reset your scanner when: 1. scanner is not properly configured so that it fails to decode barcodes; 2. you forget previous configurat ion and want to avoid its impact; 3. functions that are rarely used have[...]

** Enter Setup 4 1 Exit Setup Scan Mode Manual Mode Manual Mode (default): A trigger pull activates a decode session. The decode session continues until the barcode is decoded or the trigger is releas ed or the decode session timeout expires. ** Manual Mode Decode Session Timeo ut : This param eter sets the maximum time decode session continues dur[...]

** Enter Setup Exit Setup 4 2 Continuous Mode Continuous Mode : A trigger press activates the scanne r to scan and decode at user-s pecified intervals, i.e. the timeout between decodes. Each decode se ssion lasts until barcode is decoded or the decode session timeout expires. T o suspend/resume the operation, simply press the trigger . By default, [...]

** Enter Setup 4 3 Exit Setup Timeout between Decodes :This parameter sets the timeout between decode sessions. When a decode session ends, next session will not happen until the tim eout between decodes expires. It is programmable in 0.1s increments from 0.0s to 25.5s. The default timeout is 1.0s. Timeout bet ween Decodes Example: Set the timeout [...]

** Enter Setup Exit Setup 4 4 Reread Delay sets the time period before the scanner c an read the same barcode a second time. It protects against accidental rereads of the same barcode. This param eter is programmable in 0.1s increments from 0.1s to 25.5s. The default delay is 3.0s. If the parameter is set to 0, the delay is infinite. Note : This pa[...]

** Enter Setup 4 5 Exit Setup Sense Mode Sense Mode : The scanner activates a decode session every time when it detects a chang e in ambient illumination and meets the requirement of the image stabilization tim eout. Decode session continues until barcode is decoded or the decode session timeout expire s. A trigger pull can also activate a decode s[...]

** Enter Setup Exit Setup 4 6 Image Stabilization Timeout : The scanner waits for the image stab ilization timeout to expi re before activating a decode session every time it detects a change i n ambient ill umination. This parameter is programmable in 0.1s increments from 0.0s to 25.5s. The defaul t timeout is 0.4s. Example: Set the Image Stabiliz[...]

** Enter Setup 4 7 Exit Setup Reread Delay sets the time period before the scanner c an read the same barcode a second time. It protects against accidental rereads of the same barcode. This param eter is programmable in 0.1s increments from 0.1s to 25.5s. The default delay is 3.0s. If the parameter is set to 0, the delay is infinite. Note : This pa[...]

** Enter Setup Exit Setup 4 8 Sensitivity : This parameter specifies the degree of ac uteness of the scanner ’s response to changes in ambient illumination. The higher the s ensitivity , the lower re qui rement in illumination change to trigger the scanner . Y ou can select an appropriate degree of s ensitivity that fits the ambient environm ent.[...]

** Enter Setup 4 9 Exit Setup Command Trigger Mode Command T rigger Mode: Decode session is activated by a host command. The decode session continues until the barcode is decoded or the decode session timeout expires. Command T rigger Mode Decode Session Timeo ut : This param eter sets the maximum time decode session continues during a scan attempt[...]

** Enter Setup Exit Setup 5 0 Security Level This parameter specifies the number of times to decode a barcode during a scan attempt. The higher the security level, the lower the error rate and decoding efficiency . ** Set Security Level to 0 Set Security Level to 1 Set Security Level to 2 Set Security Level to 3[...]

** Enter Setup 5 1 Exit Setup Good Read Beep ** Good Read Be ep On Good Read Beep Off[...]

** Enter Setup Exit Setup 5 2 Good Read Beep Frequency Low ** Medium High Good Read Beep Duration 40ms **80ms 120ms[...]

** Enter Setup 5 3 Exit Setup Decode Result Notification When enabled, if a barcode does not decode, “F” is transmitted; if a barcode is decoded, “S” is appended to the barcode data as the most left character . Enable Decode Result Notification ** Disable Decode Result Notification[...]

** Enter Setup Exit Setup 5 4 Other Settings Y ou can change the following parameter settings te mporarily and the changes will be lost when you power down or reboot the scanner . Silent Mode Silent Mode On ** Silent Mode Off Note: This feature is only applicable to decode beep and will be autom atically disabled when the scanner is powered down or[...]

** Enter Setup 5 5 Exit Setup Chapter 3 Communication Settings Introduction The scanner provides a USB interface to communicate with the host device. T he host device can receive scanned data and send commands to contro l the scanner or to access/alter the configuration information of the scanner via the USB interface. USB HID-KBW ** USB HID-KBW[...]

** Enter Setup Exit Setup 5 6 Standard Keyboard When the USB HID-KBW feature is enabled, the scanner selects Standard Keyboard by d efault. Besides that, the other t wo options are provided: Emulate AL T+Ke ypad and Function Key Mapping . ** Standard Keyboard Emulate ALT+Keypad When Emulate AL T+Ke ypad is enabled, any ASCII character (0x00 - 0xFF)[...]

** Enter Setup 5 7 Exit Setup Function Key Mapping When Function Key Mapping is enabled, function character (0x00 - 0x1F) are sent as ASCII sequences over the numeric keypad. 1. CTRL Make 2. Press function key (Refer to the ASCII Function Key Mapping T able on the following page) 3. CTRL Break Function Key Mapping[...]

** Enter Setup Exit Setup 5 8 ASCII Function Key Mapping Table ASCII V alue （ HEX ） Function Key ASCII V alue （ HEX ） Function Key 00 2 10 P 01 A 11 Q 02 B 12 R 03 C 13 S 04 D 14 T 05 E 15 U 06 F 16 V 07 G 17 W 08 H 18 X 09 I 19 Y 0A J 1A Z 0B K 1B [ 0C L 1C 0D M 1D ] 0E N 1E 6 0F O 1F .[...]

** Enter Setup 5 9 Exit Setup USB Country Keyboard T ypes Keyboard layouts vary from country to count ry . All supported keyboard types are listed below . ** 1 - U.S. 2 - Belgium 3 - Brazil 4 - Canada 5 - Czech 6 - Denmark 7 - Finland 8 - France[...]

** Enter Setup Exit Setup 6 0 9 - A ustria 10 - Greece 1 1 - Hungary 12 - Israel 13 - Italy 14 - Latin A merica 15 - Netherland 16 - Norway 17 - Poland 18 - Portugal[...]

** Enter Setup 6 1 Exit Setup 19 - Romania 20 - Russia 21 - Slovakia 22 - Spain 23 - Sweden 24 - Switzerland 25 - T urkey1 26 - T urkey2 27 - UK 28 - Japan[...]

** Enter Setup Exit Setup 6 2 Inter-Keystroke Delay This parameter specifies the delay between emulated keystrokes. ** No Delay Short Delay (5ms) Medium Delay (10ms) Long Delay (15 ms)[...]

** Enter Setup 6 3 Exit Setup Convert Case This parameter is valid when the Standard Keyboard or Function Key Mapp ing is enabled. ** No Case Conversion Convert All to Upper Case Convert All to Lower Case Invert Upper and Low er Case Characters Example: When the Convert All to Lower Case feature is enabled, barcode data “AbC” is transmitted as [...]

** Enter Setup Exit Setup 6 4 Emulate Numeric Keypad When this feature is disabled, s ending barcode data is emulated as keystroke(s) on main keyboard. T o enable this feature, scan the Emulate Numeric Keypad barcode. Sendin g a number (0-9) is emulated as keystroke on numeric keypad, wher eas sending other cha racter like “+”, “_”, “*”[...]

** Enter Setup 6 5 Exit Setup USB COM Port Emulation This feature allows the host to receive data in th e way as a serial port doe s. However , you need to set communication parameters on the scanner to match the Hos t requirements. A driver is required for this feature. USB COM Port Emulation[...]

** Enter Setup Exit Setup 6 6 USB DataPipe A driver is required when using this prot ocol to communicate with the scanner . USB DataPipe[...]

** Enter Setup 6 7 Exit Setup HID-POS The HID-POS interface is recommended for new applicati on programs. It can send up to 56 characters in a single USB report and appears more efficient than USB HID-KBW. Features:  HID based, no custom driver required.  W ay more efficient in communication than USB HID-KBW and traditional RS-232 interface. [...]

** Enter Setup Exit Setup 6 8 Access the Scanner with Your Program 1. Use CreateFile to access the scanner as a HID device. 2. Use ReadFile to deliver the sc anned data to the application program. 3. Use WriteFile to send data to the scanner . For detailed information about USB and HID interfaces, go to www.USB.org . Acquire Scanned Data After a ba[...]

** Enter Setup 6 9 Exit Setup Chapter 4 Data Formatting Introduction After a successful barcode read, a string containing numbers, letters or sy mbols will be returned. In real applications, barcode data ma y be found insufficient for your needs. Y ou may wish to include additional information such as barcode type, data acquisition time or delimite[...]

** Enter Setup Exit Setup 7 0 Custom Prefix Enable/Disable Custom Prefix If custom prefix is enabled, you are allowed to append to the data a user-defined prefix that cannot exceed 5 characters. For example, if barcode data is “123” and custom prefix is “AB” , the Host will receive “AB123”. Enable Custom Prefix ** Disable Custom Prefix [...]

** Enter Setup 7 1 Exit Setup AIM ID Prefix AIM (Automatic Identificat ion Manufacturers) ID defi nes symbology identifier (For the details, see the AIM ID T able section in Appendix). If AIM ID prefix is e nabled, the scanner will add t he symbology identifier before the scanned data after decoding. Enable A IM ID Prefix ** Disable A IM ID Prefix[...]

** Enter Setup Exit Setup 7 2 CODE ID Prefix Code ID can also be used to identify barcode type. Unlike AIM ID, Code ID is user programmable. For the information of default Code ID, see the Code ID T able section in Appendix. Enable CODE ID Prefix ** Disable CODE ID Prefix Restore All Default Code IDs Restore All Default Code IDs Set Code ID Code ID[...]

** Enter Setup 7 3 Exit Setup Set Code ID Barcodes Set Code 128 Code ID Set UCC/EAN-128 Code ID Set A IM 128 Code ID Set EAN-8 Code ID Set EAN-13 Code ID Set ISSN Code ID Set ISBN Code ID Set UPC-E Code ID[...]

** Enter Setup Exit Setup 7 4 Set Code ID Barcodes (continued) Set UPC-A Code ID Set Interleaved 2 of 5 Code ID Set ITF-6 Code ID Set ITF-14 Code ID Set Deutsche 14 Code ID Set Deutsche 12 Code ID Set Matrix 2 of 5 Code ID Set Industrial 25 Code ID[...]

** Enter Setup 7 5 Exit Setup Set Code ID Barcodes (continued) Set Standard 25 Code ID Set Code 39 Code ID Set Codabar Code ID Set Code 93 Code ID Set Code 1 1 Code ID Set Plessey Code ID Set MSI-Plessey Code ID Set RSS-14 Code ID Set RSS-Limited Code ID Set RSS-Expand Code ID[...]

** Enter Setup Exit Setup 7 6 Custom Suffix Enable/Disable Custom Suffix If custom suffix is enabled, you are allowed to append to the data a user-d efined suffix that cannot exceed 5 characters. For example, if barcode data is “123” and custom suffix is “AB”, the Host will receive “123AB”. Enable Custom Suffix ** Disable Custom Suffix[...]

** Enter Setup 7 7 Exit Setup Set Custom Suffix To set a custom suffix, scan the Set Custom Suffix barcode, the numeric ba rcodes corresponding to the hexadecimal value of a desired suffix and the Save barcode. Note : A custom suffix cannot exceed 5 characters. Set Custom Suffix Example: Set the custom suffix to “AGE” (its hexadecimal value is [...]

** Enter Setup Exit Setup 7 8 T erminating Character Suffix A terminating character , such as carriage retu rn ( CR) and line feed (LF), can be used to mark the end o f data, which means nothi ng can be added after it. A terminating character suf fix cannot exceeed 5 characters. Enable/Disable Terminating Character Suffix T o enable/disable termina[...]

** Enter Setup 7 9 Exit Setup Set Terminating Character Suffix The scanner provides a shortcut for setting the terminating character su ffix to 0x0D (CR) or 0x0D,0x0A (CRLF) or 0x09 (Horizontal T ab) by scanning the following barcode. T erminating Character 0x0D ** T erminating Character 0x0D,0x0 A T erminating Character 0x09 Set T erminating Chara[...]

** Enter Setup Exit Setup 8 0 Chapter 5 Symbologies Introduction Every symbology (barcode type) has its own unique a ttributes. This chapter provid es programming barcodes for configuring the scan ner so that it can identify va rious barcode symbologies. It is recommended to disable those that are rarely used to increase the efficiency of the scann[...]

** Enter Setup 8 1 Exit Setup Code 128 Restore Factory Defaults Restore the Factory Defaul ts of Code 128 Enable/Disable Code 128 ** Enable Code 128 Disable Code 128[...]

** Enter Setup Exit Setup 8 2 Set Length Range for Code 128 The scanner can be configured to only decode Code 128 barcodes wi th lengths that fall between (inclusive) the minimum and maximum lengths. The supported maximum length is 255 characters. If minimum length is set to be greater than maximum length, the scanner only decodes Code 128 barc ode[...]

** Enter Setup 8 3 Exit Setup UCC/EAN-128 Restore Factory Defaults Restore the Factory Defaul ts of UCC/EAN-128 Enable/Disable UCC/EAN-128 ** Enable UCC/EAN-128 Disable UCC/EAN-128 Decode as Code 128[...]

** Enter Setup Exit Setup 8 4 Set Length Range for UCC/EAN-128 The scanner can be configured to only decode U CC/EAN-128 barcodes with lengths that fall between (inclusive) the minimum and maximum lengths. The supported maximum length is 255 characters. If minimum length is set to be greater than maximum length, the scanner only dec odes UCC/EAN-12[...]

** Enter Setup 8 5 Exit Setup AIM 128 Restore Factory Defaults Restore the Factory Defaul ts of A IM 128 Enable/Disable AIM 128 Enable AIM 128 ** Disable A IM 128 Decode as Code 128[...]

** Enter Setup Exit Setup 8 6 Set Length Range for AIM 128 The scanner can be configured to only decode AIM 128 barcodes with lengt hs that fall between (inclusive) the minimum and maximum lengths. The supported maximum length is 255 characters. If minimum length is set to be greater than maximum length, the scanner only decodes AI M 128 barcodes w[...]

** Enter Setup 8 7 Exit Setup EAN-8 Restore Factory Defaults Restore the Factory Defaul ts of EA N-8 Enable/Disable EAN-8 ** Enable EAN-8 Disable EA N-8 Transmit Check Digit EAN-8 is 8 digits in length with the last one as its ch eck digit used to verify the integrity of the data. ** T ransmit EAN-8 Check D igit Do Not T ransmit EAN-8 Check Digit[...]

** Enter Setup Exit Setup 8 8 Add-On Code An EAN-8 barcode can be augmented with a two-digit or five-digit add-on code to form a new one. In the examples below , the part surrounded by blue dotted line is an EAN-8 barcode while the part circled by red dotted line is add-on code. Enable 2-Digit Add-On Code ** Disable 2-Digit Add-On Code Enable 5-Dig[...]

** Enter Setup 8 9 Exit Setup Add-On Code Required This parameter is only valid when Enable 2-Digit Add-On Code and/or Enable 5-Digit Add-On Code is selected. EAN-8 Add-On Code Require d ** EAN-8 Add-On Code Not Required EAN-8 Extension Disable EAN-8 Zero Extend : T ransmit EAN-8 barcodes as is. Enable EAN-8 Zero Extend : Add five leading zeros to [...]

** Enter Setup Exit Setup 9 0 EAN-13 Restore Factory Defaults Restore the Factory Defaul ts of EAN-13 Enable/Disable EAN-13 ** Enable EAN-13 Disable EAN-13 Transmit Check Digit EAN-13 is 13 digits in length with the last one as its check digit used to verify the integrity of the data. ** T ransmit EAN-13 Check Digit Do Not T ransmit EAN-13 Check Di[...]

** Enter Setup 9 1 Exit Setup Add-On Code An EAN-13 barcode can be augmented with a two-digit or five-digit add-on code to form a n ew one. In the examples below , the part surrounded by blue dotted li ne is an EAN-13 barcode while the part circled by red dotted line is add-on code. Enable 2-Digit Add-On Code ** Disable 2-Digit Add-On Code Enable 5[...]

** Enter Setup Exit Setup 9 2 Add-On Code Required This parameter is only valid when Enable 2-Digit Add-On Code and/or Enable 5-Digit Add-On Code is selected. EAN-13 Add-On Code Requir ed ** EAN-13 Add-On Code Not Requir ed[...]

** Enter Setup 9 3 Exit Setup ISSN Restore Factory Defaults Restore the Factory Defaults o f ISSN Enable/Disable ISSN Enable ISSN ** Disable ISSN Decode as EAN-13[...]

** Enter Setup Exit Setup 9 4 ISBN Restore Factory Defaults Restore the Factory Defaults o f ISBN Enable/Disable ISBN Enable ISBN ** Disable ISBN Decode as EAN-13[...]

** Enter Setup 9 5 Exit Setup Set ISBN Format ** ISBN-13 ISBN-10[...]

** Enter Setup Exit Setup 9 6 UPC-E Restore Factory Defaults Restore the Factory Defaults o f UPC-E Enable/Disable UPC-E ** Enable UPC-E Disable UPC-E Transmit Check Digit UPC-E is 8 digits in length with the last one as its check digit used to verify the integrity of the data. ** T ransmit UPC-E Check D igit Do Not T ransmit UPC-E Check Digit[...]

** Enter Setup 9 7 Exit Setup Add-On Code A UPC-E barcode can be augmented with a two-digit or five-digit add-on code to form a new one. In the examples below , the part surrounded by blue dotted line is a UPC-E barcode while the part circled by red dotted line is add-on code. Enable 2-Digit Add-On Code ** Disable 2-Digit Add-On Code Enable 5-Digit[...]

** Enter Setup Exit Setup 9 8 Add-On Code Required This parameter is only valid when Enable 2-Digit Add-On Code and/or Enable 5-Digit Add-On Code is selected. UPC-E A dd-On Code Required ** UPC-E Add-On Code Not Require d Transmit System Character The first character of UPC-E barcode is the system character . Do Not T ransmit System Character ** T [...]

** Enter Setup 9 9 Exit Setup UPC-E Extension Disable UPC-E Extend: Transmit UPC-E barcodes as is. Enable UPC-E Extend: Extend UPC-E barcodes to make them compatible in length to UPC-A. Convert UPC-E to UPC-A: Extend UPC-E barcodes to make them compatible in format to UPC-A. Enable UPC-E Extend **Disable UPC-E Extend Convert UPC-E to UPC-A[...]

** Enter Setup Exit Setup 1 0 0 UPC-A Restore Factory Defaults Restore the Factory Defaul ts of UPC-A Enable/Disable UPC-A ** Enable UPC- A Disable UPC-A Decode as EAN-13[...]

** Enter Setup 101 Exit Setup Transmit Check Digit UPC-A is 13 digits in length with the last one as its check digit used to verify the integrity o f the data. ** T ransmit UPC- A Check Dig it Do Not T ransmit UPC-A Ch eck Digit Transmit Preamble Character Preamble characters (Country Code and System Character) can be tr ansmitted as part of a UPC-[...]

** Enter Setup Exit Setup 1 0 2 Add-On Code A UPC-A bar code can be augmented with a two-digit or five-digit add-on code to form a new one. In the examples below , the part surrounded by blue dotted line is a UPC-A barcode while the part circled by red dotted line is add-on code. Enable 2-Digit Add-On Code ** Disable 2-Digit Add-On Code Enable 5-Di[...]

** Enter Setup 103 Exit Setup Add-On Code Required This parameter is only valid when Enable 2-Digit Add-On Code and/or Enable 5-Digit Add-On Code is selected. UPC-A A dd-O n Code Required ** UPC-A A dd-On Code Not Required[...]

** Enter Setup Exit Setup 1 0 4 Interleaved 2 of 5 Restore Factory Defaults Restore the Factory Defaults o f Interleaved 2 of 5 Enable/Disable Interleaved 2 of 5 ** Enable Interleaved 2 of 5 Disable Interleaved 2 of 5[...]

** Enter Setup 105 Exit Setup Check Digit Verification A check digit is optional for Interl eaved 2 o 5 and can be added as the last digit. It is a calculated value used to verify the integrity of the data. Disable: The scanner transmits Interleav ed 2 of 5 barcodes as is. Do Not T ransmit Check Digit After V erification: The scanner checks the int[...]

** Enter Setup Exit Setup 1 0 6 Set Length Range for Interleaved 2 of 5 The scanner can be configured to only decode Interleaved 2 of 5 barcode s with lengths that fall between (inclusive) the minimum and maximum lengths. The supported maximum length is 255 characters. If minimum length is set to be greater than maximum length, the scanner only dec[...]

** Enter Setup 107 Exit Setup ITF-6 ITF-6 is a special kind of Interleaved 2 of 5 with a length of 6 characters and the last character as the check character . Restore Factory Defaults Restore the Factory Defaul ts of ITF-6 Enable/Disable ITF-6 By default, ITF-6 is decoded as Interleaved 2 of 5. Disable ITF-6 Enable ITF-6 But Do Not T ransmit Check[...]

** Enter Setup Exit Setup 1 0 8 ITF-14 ITF-14 is a special kind of Interleaved 2 of 5 with a length of 14 characters and t he last character as the check character . Restore Factory Defaults Restore the Factory Defaul ts of ITF-14 Enable/Disable ITF-14 By default, ITF-14 is decoded as Interleaved 2 of 5. Disable ITF-14 Enable ITF-14 But Do Not T ra[...]

** Enter Setup 109 Exit Setup Deutsche 14 Restore Factory Defaults Restore the Factory Defaul ts of Deutsche 14 Enable/Disable Deutsche 14 By default, Deutsche 14 is decoded as Interleaved 2 of 5. Disable Deutsche 14 Enable Deutsche 14 But Do No t T ransmit Check Digit Enable Deutsche 14 and T ransmit Check Digi t Note: It is advised not to enable [...]

** Enter Setup Exit Setup 1 1 0 Deutsche 12 Restore Factory Defaults Restore the Factory Defaul ts of Deutsche 12 Enable/Disable Deutsche 12 By default, Deutsche 12 is decoded as Interleaved 2 of 5. Disable Deutsche 12 Enable Deutsche 12 But Do No t T ransmit Check Digit Enable Deutsche 12 and T ransmit Check Digi t Note: It is advised not to enabl[...]

** Enter Setup 1 1 1 Exit Setup Matrix 2 of 5 (European Matrix 2 of 5) Restore Factory Defaults Restore the Factory Defaul ts of Matrix 2 of 5 Enable/Disable Matrix 2 of 5 ** Enable Matrix 2 of 5 Disable Matrix 2 of 5[...]

** Enter Setup Exit Setup 1 1 2 Check Digit Verification A check digit is optional for Matrix 2 of 5 and can be added as the last digit. It is a calculated value used to verify the integrity of the data. Disable : The scanner transmits Matrix 2 of 5 barcodes as is. Do Not Transmit Check Digit After Verification : The scanner checks the integrity of[...]

** Enter Setup 1 1 3 Exit Setup Set Length Range for Matrix 2 of 5 The scanner can be configured to only decode M atrix 2 of 5 barcodes with l engths that fall between (inclusive) the minimum and maximum lengths. The supported maximum length is 255 characters. If minimum length is set to be greater than maximum length, the scanner only decodes Matr[...]

** Enter Setup Exit Setup 1 1 4 Industrial 25 Restore Factory Defaults Restore the Factory Defaul ts of Industrial 25 Enable/Disable Industrial 25 ** Enable Industrial 25 Disable Industria l 25[...]

** Enter Setup 1 1 5 Exit Setup Check Digit Verification A check digit is optional for Industria l 25 and can be added as the last digit. It is a calculated value used to verify the integrity of the data. Disable : The scanner transmits Indus trial 25 barcodes as is. Do Not Transmit Check Digit After Verification : The scanner checks the integrity [...]

** Enter Setup Exit Setup 1 1 6 Set Length Range for Industrial 25 The scanner can be configured to only decode Indus trial 25 barcodes wit h l engths that fall between (inclusive) the minimum and maximum lengths. The supported maximum length is 255 characters. If minimum length is set to be greater than maximum length, the scanner only decodes Ind[...]

** Enter Setup 1 1 7 Exit Setup Standard 25 Restore Factory Defaults Restore the Factory Defaul ts of Standard 25 Enable/Disable Standard 25 ** Enable Standard 25 Disable Standard 25[...]

** Enter Setup Exit Setup 1 1 8 Check Digit Verification A check digit is optional for Standard 25 and can be added as the last digit. It is a calculated value used to verify the integrity of the data. Disable : The scanner transmits St andard 25 barcodes as is. Do Not Transmit Check Digit After Verification : The scanner checks the integrity of al[...]

** Enter Setup 1 1 9 Exit Setup Set Length Range for Standard 25 The scanner can be configured to only decode St andard 25 barcodes wi th lengths that fall between (inclusive) the minimum and maximum lengths. The supported maximum length is 255 characters. If minimum length is set to be greater than maximum length, the scanner only decodes St andar[...]

** Enter Setup Exit Setup 1 2 0 Code 39 Restore Factory Defaults Restore the Factory Defaul ts of Code 39 Enable/Disable Code 39 ** Enable Code 39 Disable Code 39[...]

** Enter Setup 121 Exit Setup Check Digit Verification A check digit is optional for Code 39 and can be added as the last digit. It is a calculated value used to verify the integrity of the data. Disable : The scanner transmits Code 39 barcodes as is. Do Not Transmit Check Digit After Verification : The scanner checks the integrity of all Code 39 b[...]

** Enter Setup Exit Setup 1 2 2 Transmit Start/Stop Characters Code 39 uses an asterisk (*) for both the start and the stop characters. You can c hoose whether or not to transmit the start/stop characters by scanning the appropriate barcode below. T ransmit Start/Stop Ch aracters ** Do Not T ransmit Start/Stop Characte rs Enable/Disable Code 39 Ful[...]

** Enter Setup 123 Exit Setup Set Length Range for Code 39 The scanner can be configured to only decode Code 39 barcodes with lengt hs that fall between (inclusive) the minimum and maximum lengths. The supported maximum length is 255 characters. If minimum length is set to be greater than maximum length, the scanner only dec odes Code 39 barcodes w[...]

** Enter Setup Exit Setup 1 2 4 Codabar Restore Factory Defaults Restore the Factory Defaul ts of Codabar Enable/Disable Codabar ** Enable Codabar Disable Codabar[...]

** Enter Setup 125 Exit Setup Check Digit Verification A check digit is optional for Codabar and can be added as the last digit. It is a calculated value use d to verify the integrity of the data. Disable : The scanner transmits Codabar barcodes as is. Do Not Transmit Check Digit After Verification : The scanner checks the integrity of all Codabar [...]

** Enter Setup Exit Setup 1 2 6 Start/Stop Characters ** T ransmit Start/Stop Characters Do Not T ransmit Start/Stop Characters ** A BCD/ABCD a s the Start/Sto p Character ABCD/TN* E a s the Start/Sto p Character abcd/abcd a s the Start/Sto p Character abcd/tn*e a s the Start/Stop Character[...]

** Enter Setup 127 Exit Setup Set Length Range for Codabar The scanner can be configured to only decode Cod abar barcodes with lengt hs that fall between (inclusive) the minimum and maximum lengths. The supported maximum length is 255 characters. If minimum length is set to be greater than maximum length, the scanner only dec odes Codaba r barcodes[...]

** Enter Setup Exit Setup 1 2 8 Code 93 Restore Factory Defaults Restore the Factory Defaul ts of Code 93 Enable/Disable Code 93 ** Enable Code 93 Disable Code 93[...]

** Enter Setup 129 Exit Setup Check Digit Verification Check digits are optional for Code 93 a nd can be added as the l ast two digits, which are calculated values used to verify the integrity of the data. Disable : The scanner transmits Code 93 barcodes as is. Do Not Transmit Check Digit After Verification : The scanner checks the integrity of all[...]

** Enter Setup Exit Setup 1 3 0 Set Length Range for Code 93 The scanner can be configured to only decode Code 93 barcodes with lengt hs that fall between (inclusive) the minimum and maximum lengths. The supported maximum length is 255 characters. If minimum length is set to be greater than maximum length, the scanner only dec odes Code 93 barcodes[...]

** Enter Setup 131 Exit Setup Code 1 1 Restore Factory Defaults Restore the Factory Defaul ts of Code 1 1 Enable/Disable Code 11 Enable Code 1 1 ** Disable Code 1 1[...]

** Enter Setup Exit Setup 1 3 2 Check Digit Verification Check digits are optional for Code 11 and can be added as the last one or two digits, which are calculated values used to verify t he integrity of the data. If the Disable option is enabled, the scanner tr ansmits Code 11 barcodes as is. Disable ** One Check Digi t, MOD1 1 T w o Check Digits,[...]

** Enter Setup 133 Exit Setup Set Length Range for Code 11 The scanner can be configured to only decode Code 11 barcodes with lengt hs that fall between (inclusive) the minimum and maximum lengths. The supported maximum length is 255 characters. If minimum length is set to be greater than maximum length, the scanner only dec odes Code 11 barcodes w[...]

** Enter Setup Exit Setup 1 3 4 Plessey Restore Factory Defaults Restore the Factory Defaul ts of Plessey Enable/Disable Plessey Enable Plessey ** Disable Plessey[...]

** Enter Setup 135 Exit Setup Check Digit Verification Check digits are optional for Plessey and can be added as the last one or two digits, which are calculated values used to verify t he integrity of the data. Disable : The scanner transmits Plessey barcodes as is. Do Not Transmit Check Digit After Verification : The scanner checks the integrity [...]

** Enter Setup Exit Setup 1 3 6 Set Length Range for Plessey The scanner can be configured to only decode Plessey barcode s with lengths that fall between (inclusive) the minimum and maximum lengths. The supported maximum length is 255 characters. If minimum length is set to be greater than maximum length, the scanner only decodes Plessey barcodes [...]

** Enter Setup 137 Exit Setup MSI-Plessey Restore Factory Defaults Restore the Factory Defaul ts of MSI-Plessey Enable/Disable MSI-Plessey Enable MSI-Plessey ** Disable MSI-Plessey[...]

** Enter Setup Exit Setup 1 3 8 Check Digit Verification Check digits are optional for MSI-Plessey and can be a dde d as the last one or two digits, which are calculated values used to verify the integrity of the data. If the Disable option is enabled, the scanner transmi ts MSI-Plessey barcodes as is. Disable ** One Check Digi t, MOD10 T w o Check[...]

** Enter Setup 139 Exit Setup Set Length Range for MSI-Plessey The scanner can be configured to only decode MSI-Plessey barcodes with l engths that fall between (inclusive) the minimum and maximum lengths. The supported maximum length is 255 characters. If minimum length is set to be greater than maximum length, the scanner only dec odes MSI-Plesse[...]

** Enter Setup Exit Setup 1 4 0 RSS-14 Restore Factory Defaults Restore the Factory Defaul ts of RSS-14 Enable/Disable RSS-14 ** Enable RSS-14 Disable RSS-14 Transmit Application Identifier “01” ** T ransmit A p plication Identifier “01” Do Not T ransmit A pplication Id entifier “01”[...]

** Enter Setup 141 Exit Setup RSS-Limited Restore Factory Defaults Restore the Factory Defaul ts of RSS-Limited Enable/Disable RSS-Limited ** Enable RSS-Limited Disable RSS-Limited Transmit Application Identifier “01” ** T ransmit A p plication Identifier “01” Do Not T ransmit A pplication Id entifier “01”[...]

** Enter Setup Exit Setup 1 4 2 RSS-Expand Restore Factory Defaults Restore the Factory Defaul ts of RSS-Expand Enable/Disable RSS-Expand ** Enable RSS-Expand Disable RSS-Expand[...]

143 Appendix Factory Defaults T able Parameter Factory Default Remark S y stem Settin g s Barcode Programming Enabled Programming Barcode Data Do not send Scan Mode Manual Mode Manual Mode Decode Session T imeout 15s 1-255s; 0: infinite. Continuous Mode Decode Session T imeout 15s 1-255s; 0: infinite. T imeout between Decodes 1.0s 0.0-25.5s Reread [...]

1 4 4 Parameter Factory Default Remark Communication Settings USB Interface USB HID-KBW Other options: DataPipe, USB COM Port Emulation, HID-POS USB HID-KBW Input Mode Standard Keyboard USB Country Keyboard T ype U.S. Inter-Keystroke Delay No delay Convert Case No Conversion Emulate Numeric Keypad Disabled Data Formatting Prefix Sequence Code ID+Cu[...]

145 Parameter Factory Default Remark Code 128 Code 128 Enabled Minimum Length 1 No less than 1 (including check digit) Maximum Length 80 UCC/EAN-128 （ GS1-128 ） UCC/EAN-128 Enabled Minimum Length 1 No less than 1 (including check digit) Maximum Length 80 AIM 128 AIM 128 Disabled Minimum Length 1 No less than 1 (including check digit) Maximum Le[...]

1 4 6 Parameter Factory Default Remark UPC-E UPC-E Enabled Check Digit T ransmit 2-Digit Add-On Code Disabled 5-Digit Add-On Code Disabled Add-On Code Not required Extend to UPC-A Disabled System Character T ransmit UPC-A UPC-A Enabled Check Digit T ransmit 2-Digit Add-On Code Disabled 5-Digit Add-On Code Disabled Add-On Code Not required T ransmit[...]

147 Parameter Factory Default Remark Matrix 2 of 5 Matrix 2 of 5 Enabled Check Digit V erification Disabled Check Digit Do not transmit Minimum Length 6 No less than 2 (including check digit) Maximum Length 80 Industrial 25 Industrial 25 Enabled Check Digit V erification Disabled Check Digit Do not transmit Minimum Length 6 No less than 2 (includin[...]

1 4 8 Parameter Factory Default Remark Codabar Codabar Enabled Check Digit V erification Disabled Check Digit Do not transmit Start/Stop Characters Tr a n s m i t Start/Stop Character Format A BCD/ABCD Minimum Length 4 No less than 1 (including check digit) Maximum Length 60 Code 93 Code 93 Enabled Check Digit V erification Enabled Check Digit Do n[...]

149 Parameter Factory Default Remark MSI-Plessey MSI-Plessey Disabled Check Digit V erification One check digit, MOD10 Check Digit Do not transmit Minimum Length 4 No less than 2 (including check digit) Maximum Length 60 RSS-14 RSS-14 Enabled AI (Application I dentifier) Tr a n s m i t RSS-Limited RSS-Limited Enabled AI (Application I dentifier) Tr[...]

1 5 0 AIM ID T able Symbology AIM ID Remark Code 128 ]C0 Standard Code 128 UCC/EAN 128 (GS1-128) ]C1 FNC1 is the character ri ght after the start character AIM 128 ]C2 FNC1 is the 2nd charac ter after the start character EAN-8 ]E4 Standard EAN-8 ]E4….]E1… EAN-8 + 2-Digit Add-On Code ]E4….]E2… EAN-8 + 5-Digit Add-On Code EAN-13 ]E0 Standard [...]

151 Symbology AIM ID Remark Code 39 ]A0 T ransmit barcodes as is; Full ASCII disabled; no check digit verification ]A1 One check digit, MOD 43; transmit check digit ]A3 One check digit, MOD 43; do not transmit check digit ]A4 Full ASCII enabled; no check digit ver i fi c at i o n ]A5 Full ASCII enabled; MOD43; transmit check digit ]A7 Full ASCII en[...]

1 5 2 Code ID T able Symbology Code ID Code 128 j UCC/EAN-128 u AIM 128 f SETTING 128 t EAN-8 g EAN-13 d ISSN n ISBN B UPC-E h UPC-A c Interleaved 2 of 5 e ITF-6 r ITF-14 q Deutsche 14 w Deutsche 12 l Matrix 2 of 5(European Matrix 2 of 5) v Industrial 25 i Standard 25 s Code 39 b Codabar a Code 93 y Code 1 1 z Plessey p MSI-Plessey m RSS-14 D RSS-L[...]

153 ASCII T able Hex Dec Char 00 0 NUL (Null char .) 01 1 SOH (Start of Header) 02 2 STX (Start of T ext) 03 3 ETX (End of T ext) 04 4 EOT (En d of T ransmission) 05 5 ENQ (Enquiry) 06 6 ACK (Acknowledgment) 07 7 BEL (Bell) 08 8 BS (Backspace) 09 9 HT (Horizontal T ab) 0a 10 LF (Line Feed) 0b 11 VT (V ertical T ab) 0c 12 FF (Form Feed) 0d 13 CR (Ca[...]

1 5 4 Hex Dec Char 1e 30 RS (Request to Send) 1f 31 US (Unit Separator) 20 32 S P ( S p a c e ) 21 33 ! (Exclamation Mark) 22 34 " (Double Quote) 23 35 # (Number Sign) 24 36 $ (Dollar Sign) 25 37 % (Percent) 26 38 & (Ampersand) 27 39 ` (Single Quote) 28 40 ( (Right / Closing Parenthesis) 29 41 ) (Right / Closing Parenthesis) 2a 42 * (Aster[...]

155 Hex Dec Char 3e 62 > (Greater Than) 3f 63 ? (Question Mark) 40 64 @ (A T Symbol) 41 65 A 42 66 B 43 67 C 44 68 D 45 69 E 46 70 F 47 71 G 48 72 H 49 73 I 4a 74 J 4b 75 K 4c 76 L 4d 77 M 4e 78 N 4f 79 O 50 80 P 51 81 Q 52 82 R 53 83 S 54 84 T 55 85 U 56 86 V 57 87 W 58 88 X 59 89 Y 5a 90 Z 5b 91 [ (Left / Opening Bracket) 5c 92 (Back Slash) [...]

1 5 6 Hex Dec Char 5e 94 ^ (Caret / Circum fl ex) 5f 95 _ (Underscore) 60 96 ' (Grave Accent) 61 97 A 62 98 B 63 99 C 64 100 d 65 101 e 66 102 f 67 103 g 68 104 h 69 105 i 6a 106 j 6b 107 k 6c 108 l 6d 109 m 6e 1 10 n 6f 1 1 1 o 70 1 12 p 71 1 13 q 72 1 14 r 73 1 15 s 74 1 16 t 75 1 17 u 76 1 18 v 77 1 19 w 78 120 x 79 121 y 7a 122 z 7b 123 {[...]

157 Digit Barcodes 0 ~ 5 0 1 2 3 4 5[...]

1 5 8 6~ 9 6 7 8 9[...]

159 A ~ F A B C D E F[...]

1 6 0 Save/Cancel Barcodes After reading numeric barcode(s), you need to scan the Save barcode to save the data. If you scan the wrong digit(s), you can either scan the Cancel the Last Digit barcode and then the correct digit, or scan the Cancel All Digits barcode and then the digits you want. For instance, after reading the Decode Session Timeout [...]

161 F1~F12 When the USB HID-KBW feature is enabled, scanning one of the following barcodes will send the corresponding function key. F1~F6 F1 F2 F3 F4 F5 F6[...]

1 6 2 F7~F12 F7 F8 F9 F10 F1 1 F12[...]

163 Headquarters / 总部 福建新大陆自动识别技术有限公司 地址：福建省福州市马尾区儒江西路 1 号新大陆科技园 邮编： 350015 电话： +86 - （ 0 ） 591-83 979222 传真： +86 - （ 0 ） 591-83 979208 E-mail ： mark eting@nlscan.com WEB ： www . nlscan.com Newland Europe BV/ 欧洲新大陆有限公司 Rol[...]