Pentair HP 400, HP 600, HP 800, HP 1000, HP 230 инструкция обслуживания

Part #471949 Revision #A © 2001 HydroTemp Manufacturing Co., Inc. Note: Specifications may change without notice. Owners Operational Information Only Technicians See Separate Installation Manual OWNERS OPERA TION MANUAL Models: MiniMax Plus HP 400 (XLS400) MiniMax Plus HP 600 (XLS600) MiniMax Plus HP 800 (XLS800) MiniMax Plus HP 1000 (XLS1000) Min[...]

OWNERS SECTION - TABLE OF CONTENTS 1. OPERATIONAL INSTRUCTIONS .............................................................................................. a. Introduction & Design Features b. Heater Control Panels & L.E.D. Status Lights 2. START UP PROCEDURES ...............................................................................[...]

Owners/users should contact the factory service department for advice at: HYDROTEMP MANUFACTURING CO., INC. 12155 Metro Pkwy, Ste. 5 Ft Myers, FL 33912 (941) 768-1555 (941) 768-2856 (fax) www.warmpool.com RETURN ON INVESTMENT The costs of installing a heat pump are somewhat higher than a gas heater but you will save enough in opera- tional costs to[...]

4 Super Quiet & Highly Ef ficient Compressor Desig n Sturdy Elevated Fiberglass Rust Proof Bottom Provides Proper Drainage Large Aluminum & Copper Lanced Fin Evaporator Air Coil and Coil Guard Easy Connect 2 Inch Plumbing With "Internal Automatic Bypass" Up To 90 GPM Sturdy Rust Proof Fiberglass Top Non Fading Quiet High Volume Fa[...]

The electrical panel has an isolated compartment, located within the me- chanical compartment to prevent corrosion there. The heat from the com- pressor located just below the electrical compart- ment helps eliminate mois- ture as well. This exclu- sive design will substan- tially extend the life cycle of the heater. The fiber- glass cabinet is cor[...]

DUAL THERMOSTAT CONTROL PANEL THERMOSTAT The thermostat dial is just like any other, when you set it at a certain setting the heater will heat up to that temperature and then shut off. When the pool/spa wa- ter temperature drops below this setting the heater will come on and start heating the water back up to the setting on the thermostat. You will[...]

POOL MODE "Yellow": The yellow pool mode in- dicator light lets you know that you have selected the pool mode with the pool /spa select switch, (dual ther- mostat control only). This light will be off when the control is in spa mode. SPA MODE "Orange": The orange spa mode indicator light tells you that you have selected the spa [...]

8 START UP PROCEDURES COMPRESSOR TIME DELAY BE AWARE THERE IS A 5 TO 7 MINUTE TIME DE- LAY BEFORE THE COMPRESSOR WILL START ONCE THE UNIT IS TURNED ON OR WHENEVER IT RESTARTS. All models. TURN T-STAT ALL THE WAY DOWN Make sure the thermostat dial is turned all the way to the “LEFT” so the unit will not start until you are ready. Then turn the c[...]

9 HEAT EXCHANGER The compressed hot refrigerant releases it's heat to the pool water inside the heat exchanger. The exchanger is a tube within a tube construction, water passing through the inner tube, hot gas passing through the outer tube. The refriger- ant is transformed into a liquid state as it exits the heat exchanger. There- fore it is [...]

NORMAL RUNNING TIME The heat pump system extracts the heat from the out- side air and delivers it to your pool. Therefore it pro- duces more BTU's (heat) the warmer it is outside. So take advantage of the higher air temperatures during the day by setting the timer for the warmest hours. Win- ter operation (during cold fronts) may require longe[...]

THERMOSTAT SETTING There are no temperature reading numbers printed on the thermostat dial due to calibration changes from unit to unit. The demand for exact temperatures should be regulated by using a high quality thermometer right in the pool water. Normal temperatures for pools are 78 to 82 degrees F. Spa temperatures are 98 to a maximum of 104 [...]

RERADIATION CONVECTION EVAPORATION WIND CONDUCTION Pool Shell Pool Surface Warm Pool Water UNDERSTANDING HEA T LOSS It is important to understand how your pool loses heat. The greatest heat loss occurs at the water surface. You will need to adjust the operational time to compensate for added heat loss during the colder months. See the diagram on th[...]

CONTROLLING HEAT LOSS A good way to control heat loss is to slow the wind speed through your pool area by placing plants such as shrubs or bushes around the pool's perimeter. Plants will break up the air flow and diffuse the wind speed. If the pool area is to be fenced in, choose a wood shadow box type design. A solid type fence or wall does n[...]

OWNERS MAINTENANCE & CARE There are some considerations that should be taken concerning the environment where your heater is installed. The heater is usually placed near the pool filtering system. There are certain things in this area you will need to be aware of to insure long life and prevent unnecessary damage. SPRINKLERS Make sure there are[...]

15 WATER PIPING LEAK ? When the unit operates, it will produce condensation that will drain from the bottom of the unit. Do not mistake condensation with a water piping leak. There is a certain procedure to follow to check the unit for leaks: Shut the heat pump and filtering system off. Allow all the condensation to drain from the unit for at least[...]

FILTER CLEANING & CARE Your filter system should be cleaned at least twice a month. See manufacturer's directions for proper filter cleaning methods. Size and conditions may require you to clean the filter more often. A filter is considered "dirty", whenever it restricts the flow rate by 10% or more. You can use the pressure gaug[...]

Often times, when these auto vacuums begin to wear, they require more suction from the pump to operate. Diverting all vacuum through the auto vac may help it run better but will restrict the overall water flow through the entire system and the heater. If you have a low water flow situation where the heater is not getting enough water through the co[...]

The heat pump in equipped with a internal "Automatic Bypass" valve. A variable rate spring valve is used to regulate the wa- ter flow through the heat ex- changer. Steady flow will be de- livered over a wide range of flow rates. This automatic valve can handle a maximum flow rate of 90 gallons per minute. The automatic valve will com- pen[...]

8" 2 LB CHEMICAL RESISTANT CHECK VALVE Part# 888-018 LOOP ABOVE TO POOL CHLORI- NATOR FROM HEATER The chemical resistant check valve and loop must be in- stalled with all types of chlorinators to prevent chlorine migration to the heater. The loop should extend at least 8 inches above the chlorinator top. The chemical resistant check valve shou[...]

W A TER BALANCE MAINTENANCE The chemical balance of your pool/spa water and the methods used in adding pool chemicals will directly effect the life of your heater. Like no other precaution you could take, it is very important that these guidelines are followed in order to prevent damage to the heat exchanger/water coil and possibly the entire syste[...]

21 These chemical outlines should not be considered as a “how to” balance your pool/spa water, but just a refer- ence on how chemical balance effects the heater and gives suggested test values. You should always consult a pool professional and follow all chemical manufacturers di- rections, unless they conflict with this manual. CHLORINE Chlori[...]

22 TOTAL ALKALINITY Total Alkalinity is a test given to determine the over- all mineral content of the water. Total alkalinity lev- els should be within the range from 90 p.p.m. to 120 p.p.m. The total alkalinity is described as a buffer against acetic conditions and acts as a stabilizer for the pH. It keeps the pH from fluctuating up and down. A l[...]

CHLORINATOR PLACEMENT 1. All chlorinators should have a chemical resistant check valve and a loop plumbed at least 8 inches above the chlorinator, between it and the heater, as far down line from the heater as possible. 2. Never plumb a chlorinator into the suction side of the circulation pump. All automatic chemical feeders should be as far down l[...]

24 COMMERCIAL FEEDERS We strongly suggest that all chemical feeders be placed "down line" of the heater. In a "closely monitored" commercial pool situation where a vacuum type filter system is used in conjunction with a surge tank, there are some exceptions to chemical injection. Some liquid chlorine (sodium hypochlorite) feeder[...]

SHUT DOWN & FREEZE PROTECTION PROCEDURES When shutting the unit down for the end of the swimming season you must consider some items to protect the unit from inclement weather. It is best in most situations to shut the unit off by turning the thermostat all the way down, to the "left". Leave power ,(circuit breaker), to the unit “on[...]

POSSIBLE CAUSE CONDITION POSSIBLE REMEDY All control lights off. Unit will not start. Control Ready light ON. Water Press. OK light OFF. T-Stat On light OFF. Low & High Press. lights OFF. Unit will not start. Low water flow through heater. Dirty or worn filters or clogged lint traps. Clogged filter pump impeller. Improper plumbing valve setting[...]

Control Ready light ON. Water Press. OK light ON T-Stat On light ON Fan is not turning. Unit will not start. Low water flow through heater. Dirty or worn filters or clogged lint traps. Clogged filter pump impeller. Improper plumbing valve settings. Wait for the 90 second compressor time delay. Clean entire filtering system and or replace fil- ter e[...]

MANDATORY BONDING TO POOL STEEL (This is in addition to electrical ground) Make sure that the unit cabinet is bonded to the pool steel. Most codes require that the circulation pump be bonded as well. You can connect at that point using at least a #6 gauge or larger solid copper wire. Use the external bond lug on the cabinet to insure a good bond. B[...]

HOW TO GET SERVICE When you experience trouble with your unit, you should follow these simple procedures before requesting service on your pool/spa heat pump. 1. You should follow all start up procedures as described in this booklet. Without exception you should clean the filtering system thoroughly, consult the manufacturers directions for proper [...]

30 GLOSSARY OF TERMS A/C Contractor: A company licensed by the state and local au- thorities to perform heating ventilation and air-conditioning in- stallation or repair including pool heat pumps. Allow no others to repair this unit. Acetic: Describing pool/spa water that is aggressive in nature with a Ph value below 7.6. Like acid, orange juice, v[...]

Circuit Breaker: An automatic switch that will shut the power off to an electrical device (heater, circulation pump) when an over- load or short occurs. Located in the electrical supply panel in your home or near the associated equipment. Circulation Pump: An electric water pump that circulates water through the filter and other pool related equipm[...]

32 Floating Thermometer: A thermometer that floats on the water surface with the main sensing bulb in the water. Indicates the ac- tual pool or spa temperature it’s floating in. A tie on type will work the same. Flow Control Valve: A valve or check valve that controls water flow either automatically or manually. Freon™: Trade name for a type of[...]

Serial Number: A twelve digit number on the identification sticker on the outside of the heater cabinet. Needed for all records, war- ranty request etc. Shadow-Box Fence: A fence that is made to allow air to pass through it freely without restriction. Shock Treatment: Adding a larger than normal dose of chlorine to the pool water to kill contaminat[...]

34 This page is blank.[...]

35 This page is blank.[...]

Manufactured by: © 2001 HydroT emp Manufacturing Co., Inc. 941-768-1555 www.warmpool.com Heat Pumps[...]