Pro-Tech EB-471LF M1 инструкция обслуживания

USER’S MANUAL EB-471LF ULV Celeron ® M 3.5” Embedded Card With VGA/ SOUND/ LAN EB-471LF M1[...]

Copyright Notice EB-471LF Celeron® M 3.5” Embedded Card With VGA /Sound/LAN OPERATION MANUAL COPYRIGHT NOTICE This operation m anual is meant to assist bot h Embedded Computer manufacturers and end users in inst alling and setting up the system. The information contained in this document is subject to change without any notice. This m anual is c[...]

Copyright Notice FCC NOTICE This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Ru les. These limits are designed to provide reasonable protection against harm ful interference when the equ ipment is operated in a comm ercial environment. Thi s equipment genera tes, uses, a[...]

Contents TABLE OF CONTENTS CHAPTER 1 INTRODUCTION 1-1 About This Manual ........................................................ 1-2 1-2 System Specification ...................................................... 1-3 1-3 Safety Precautions ......................................................... 1-5 CHAPTER 2 HARDWARE CONFIGURATION 2-1 Jumper &[...]

Contents CHAPTER 3 SOFTWARE UTILITIES 3-1 Introduction …………..........................................…....... 3-2 3-2 VGA Driver Utility ……………………………….…… 3-2 3-3 Flash BIOS Update ..............................................…....... 3-4 3-4 LAN Driv er Utility …...........................................?[...]

Page:1-1 INTRODUCTION This chapter gives you the i nformation for EB-471LF. It also outlines the System specification. Section includes: z About This Manual z System Specifications z Safety precautions Experienced users can skip to chapter 2 on page 2-1 for Quick Start. CHAPTER 1[...]

Chapter 1 Introduction Page: 1-2 EB-471LF USER ′ S MANUAL 1-1. ABOUT THIS MANUAL Thank you for purchasing our EB-471LF Celeron® M3.5” Em bedded Card enhanced with VGA /Sound/ LAN, which i s fully PC / AT com patible. EB- 471LF provides faster processing speed, greater expandability and can handle more task than before. This manual is de signed[...]

Chapter 1 Introduction EB-471LF USER ′ S MANUAL Page: 1-3 1-2. SYSTEM SPECIFICATION z CPU : Intel® Celeron® M processor Ultra Low Voltage without L2 cache onboard Available at 600MHz System bus frequency at 400MHz Auto detect voltage regulat or z SYSTEM CHIPSET : Intel® 852GM chipset z MEMORY : Supports up to 1 GB DDR SDRAM . One 200-pin DDR S[...]

Chapter 1 Introduction Page: 1-4 EB-471LF USER ′ S MANUAL z DISPLAY : Built in Intel 852GM, support CRT, LCD. z IDE INTERFACE : One IDE ports support up to two IDE devices. Supports UDMA 33/66/100. z LAN INTERFACE : Intel® 82562ET 10/100 Base-T z SOUND: AC '97 Codec. Reatel ALC202A. Fully Com pliant AC '97 Analog I/O Com ponent z SERIA[...]

Chapter 1 Introduction EB-471LF USER ′ S MANUAL Page: 1-5 z OPERATING TEMPERATURE : 0 to 60 ° C (32 ° F to 140 ° F) z INPUT POWER REQUIREMENT : AT power: +5V, +12V Only +5V: +5V only provi de power for SBC, It does not have enough power to support expansion card. z BOARD DIMENSION : 102mm x 145mm (4.02” x 5.71”) z BOARD NET WEIGHT : 290 gr[...]

Page 2-1 HARDWARE CONFIGURATION ** QUICK START ** CHAPTER 2 Helpful informati on describes the jumper & connector settings, and component locati ons. Section includes: z Jumper & Connector Quick R eference Table z Component Locati ons z Configuration and Jum per settings z Connector’s Pin Assignm ents[...]

Chapter 2 Hardware Config uration Page: 2-2 EB-471LF USER ′ S MANUAL 2-1. JUMPER & CONNECTOR QUICK REFERENCE TABLE COM Port Connector ....................…..................……… COM1, COM2 RS232/422/485 (COM2) Selection .....................……… JP1 Keyboard/Mouse Connector ..........…………......…… DIN1 Reset Connect or [...]

Chapter 2 Hardware Config uration EB-471LF USER ′ S MANUAL Page: 2-3 2-2. COMPONENT LOCATIONS J2 1 LVDS1 2 JSFAN1 PW1 43 44 USB1 IDE1 1 2 JP1 2 1 J1 2 1 JPANEL1 COM1 COM2 2 1 JP2 J TV1 JP4 DIN1 VGA1 LED1 JP5 BZ1 AC97 INTEL Celeron-M 1 30 LAN1 1 5 61 0 11 15 EB-471LF Connector, Jumper and Component locations[...]

Chapter 2 Hardware Config uration Page: 2-4 EB-471LF USER ′ S MANUAL 2-3. HOW TO SET THE JUMPERS You can configure your board by setti ng jumpers. Jum per is consists of two or three met al pins with a plasti c base mounted on the card, and by using a small pl astic " cap " , Also known as the jum per cap (with a metal contact inside), [...]

Chapter 2 Hardware Config uration EB-471LF USER ′ S MANUAL Page: 2-5 JUMPER DIAGRAMS 2 pin Jumpe r loo ks l i ke t his Ju mper Ca p looks like this 3 pin Jumpe r loo ks l i ke t his Ju mper Bl ock loo ks l i ke t his JUMPER SETTINGS Looks like this 3 pin Jump er 2-3 pin close( ena bl ed) Looks like this Jumper Bl ock 1-2 pin close( ena bl ed) 2 p[...]

Chapter 2 Hardware Config uration Page: 2-6 EB-471LF USER ′ S MANUAL 2-4. COM PORT CONNECTOR COM1 : COM1 Connector COM1 is fixed as RS-232. The pin assignment is as follows : PIN ASSIGNMENT 1 DCD1 2 RX1 3 TX1 4 DTR1 5 GND 6 DSR1 7 RTS1 8 CTS1 9 RI1 10 NC COM2 : COM2 Connector The COM2 is selectable as R S-232/422/485. The pin assignment is as fol[...]

Chapter 2 Hardware Config uration EB-471LF USER ′ S MANUAL Page: 2-7 2-5. RS232/422/485 (COM2) SELECTION JP1 : RS-232/422/485 (COM 2) Selection This connector is used to set the COM 2 function. The jumper settings are as follows : COM 2 Function Jumper Settings (pin closed) Jumper Illustrations RS-232 Open RS-422 1-2, 3-4, 9-10 RS-485 1-2, 5-6, 7[...]

Chapter 2 Hardware Config uration Page: 2-8 EB-471LF USER ′ S MANUAL 2-6. KEYBOARD/MOUSE CONNECTOR DIN1 : Keyboard/Mouse Connector The pin assignments are as follows : PIN ASSIGNMENT 1 KB_DATA 2 MS_DATA 3 GND 5 K/B_VCC 6 KB_CLK 8 MS_CLK 2-7. RESET CONNECTOR JPANEL1 (7,8) : Reset Connector. The pin assignment is as follows : PIN ASSIGNMENT 7 GND 8[...]

Chapter 2 Hardware Config uration EB-471LF USER ′ S MANUAL Page: 2-9 2-9. EXTERNAL SPEAKER CONNECTOR JPANEL1 (5, 6) : External Speaker Connector The pin assignment is as follows : PIN ASSIGNMENT 5 SPK1 6 SPK_VCC 2-10. POWER LED CONNECTOR JPANEL1 (1, 3) : Power LED Connector The pin assignment is as follows: PIN ASSIGNMENT 1 VCC_R 3 GND 2-11. IRDA[...]

Chapter 2 Hardware Config uration Page: 2-10 EB-471LF USER ′ S MANUAL 2-12. SYSTEM FAN CONNECTOR JSFAN1 : System Fan connector The pin assignment is as follows: PIN ASSIGNMENT 1 GND 2 +12V 3 FAN0 2-13. VGA CONNECTOR VGA1 : VGA CRT Connector The pin assignments are as follows: PIN ASSIGNMENT 1 RED 2 GREEN 3 BLUE 4 NC 5 GND 6 GND 7 GND 8 GND 9 VGA_[...]

Chapter 2 Hardware Config uration EB-471LF USER ′ S MANUAL Page: 2-11 2-14. HARD DISK DRIVE CONNECTOR IDE1: Hard Disk Drive Connector The pin assignments are as follows: PIN ASSIGNMENT PIN ASSIGNMENT 1 IDERSTJ 2 GND 3 PDD7 4 PDD8 5 PDD6 6 PDD9 7 PDD5 8 PDD10 9 PDD4 10 PDD11 11 PDD3 12 PDD12 13 PDD2 14 PDD13 15 PDD1 16 PDD14 17 PDD0 18 PDD15 19 GN[...]

Chapter 2 Hardware Config uration Page: 2-12 EB-471LF USER ′ S MANUAL 2-15. UNIVERSAL SERIAL BUS CONNECTOR USB1: Universal Serial Bus Connector The pin assignments are as follows: PIN ASSIGNMENT 1 VCCUSB0 2 USBP0N 3 USBP0P 4 GND 5 GND 6 VCCUSB0 7 USBP1N 8 USBP1P 9 GND 10 GND 2-16. LAN CONNECTOR LAN1: LAN Connector The pin assignments are as follo[...]

Chapter 2 Hardware Config uration EB-471LF USER ′ S MANUAL Page: 2-13 2-17. CLEAR CMOS DATA SELECTION JP3 : Clear CMOS Data Selection The selections are as follows : FUNCTION JUMPER SETTING (pin closed) JUMPER ILLUSTRATION Normal Open Clear CMOS Close *** Manufacturing Default i s set as Normal. Note: To clear CMOS data, user must pow er-off the [...]

Chapter 2 Hardware Config uration Page: 2-14 EB-471LF USER ′ S MANUAL 2-18. POWER REQUIREMENT SELECTION JP2 : Power Requirem ent Selection The selections are as follows: Power Selection JUMPER SETTINGS (pin closed) JUMPER ILLUSTRATION +5V & +12V 1-3, 2-4 +5V Only 3-5, 4-6 ** Manufacturin g default: +5V Only **[...]

Chapter 2 Hardware Config uration EB-471LF USER ′ S MANUAL Page: 2-15 2-19. AT POWER CONNECTOR PW1 : AT Power Connector The pin assignments are as follows: 2-20. INVERTER CONNECTOR J2 : Inverter Connector The pin assignment is as follows: PIN ASSIGNMENT 1 +12 2 GND 3 +5V 4 GND 5 LVDS_BKLTEN PIN ASSIGNMENT 1 VCC12EX 2 GND 3 GND 4 VCC[...]

Chapter 2 Hardware Config uration Page: 2-16 EB-471LF USER ′ S MANUAL 2-21. RESET/NMI WATCHDOG SELECTION JP4 : Reset/NMI Watchdog Sel ection The selections are as follows: FUNCTION JUMPER SETTING (pin closed) JUMPER ILLUSTRATION RESET 1-2 NMI 3-4 ** Manufactur ing default: Reset.  User may select to use the Reset or NMI watchdog. NMI, also kno[...]

Chapter 2 Hardware Config uration EB-471LF USER ′ S MANUAL Page: 2-17 2-22. LVDS CONNECTOR LVDS1 : LVDS Connector. The pin assignments are as follows: PIN ASSIGNMENT PIN ASSIGNMENT 1 LVDS_VCC 2 GND 3 ZCM 4 ZCP 5 GND 6 Z2M 7 Z2P 8 GND 9 Z1M 10 Z1P 11 Z3P 12 Z3M 13 Z0P 14 Z0M 15 GND 16 YCP 17 YCM 18 GND 19 Y2P 20 Y2M 21 GND 22 Y1P 23 Y1M 24 GND 25 [...]

Chapter 2 Hardware Config uration Page: 2-18 EB-471LF USER ′ S MANUAL 2-23. PANEL VOLTAGE SELECTION JP5 : Panel Voltage Selection. The selections are as follows: SELECTION JUMPER SETTING JUMPER ILLUSTRATION LVDS_VCC3 1-3, 2-4 LVDS_VCC5 3-5, 4-6[...]

Chapter 2 Hardware Config uration EB-471LF USER ′ S MANUAL Page: 2-19 2-24. SOUND CONNECTOR J1 : Sound Connector. The pin assignments are as follows: PIN ASSIGNMENT 1 MIC-IN 2 NC 3 GND 4 GND 5 LINE-L 6 LINE-R 7 GND 8 GND 9 SPK-L 10 SPK-R 2-25. TV-OUT CONNECTOR JTV1 : TV-Out Connector. The pin assignments are as follows: PIN ASSIGNMENT 1 TVYFCC2 2[...]

Chapter 2 Hardware Config uration Page: 2-20 EB-471LF USER ′ S MANUAL 2-26. LAN LED LED1 : LAN LED The pin assignments are as follows: PIN ASSIGNMENT 1+ ACTLEDJ 1- LILEDJ 2+ RJ45VCCA 2- SPLEDJ[...]

Page: 3-1 SOFTWARE UTILITIES This chapter comprises the detaile d inform ation of VGA driver, LAN driver, and Flash BIOS update . It also describes how to install the watchdog tim er configuration. Section includes: z VGA Driver Utility z Flash BIOS Update z LAN Driver Utility z Sound Driver Utility z Intel® Chipset Software Installation Utility z[...]

Chapter 3 Software Configuration Page:3-2 EB-471LF USER ′ S MANUAL 3-1. INTRODUCTION Enclosed with our EB-471LF package is our driver utility, which may comes in a form of a CD ROM disc or floppy diskettes. For CD ROM disc user, you will only need some of the files contain ed in the CD ROM disc, please kindly refer to the followin g chart: Filena[...]

Chapter 3 Software Configuration EB-471LF USER ′ S MANUAL Page:3-3 1. Win 9X program 2. Win NT4.0 program 3. Win 2000 program 4. Win XP program 3-2-1. Installation of VGA Driver: To install the VGA Driver, simp ly follow the following steps: 1. Place insert the Utility Disk into Floppy Disk Drive A/B or CD ROM drive. 2. Under Windows 9X/NT4.0/200[...]

Chapter 3 Software Configuration Page:3-4 EB-471LF USER ′ S MANUAL 3-3. FLASH BIOS UPDATE 3-3-1. System BIOS Update: Users of EB-471LF can use the program “Awdflash.exe” cont ained in the Utility Disk for system BIOS and VGA BIOS update. 3-3-2. To update VGA BIOS for LCD Flat Panel Display: As EB-471LF user, you have to update the VGA BIOS fo[...]

Chapter 3 Software Configuration EB-471LF USER ′ S MANUAL Page:3-5 FLASH MEMORY WRITER v7.XX (C) Award Software 2001 All Ri ghts Reserved Flash Type – SST 49LF004A /3.3V File Nam e to Program: H20bxxxx.bin Checksum: XXXXX Error Message : Are You Sure To Program (Y/N) Select " Y " , and the BIOS will be renewed. W hen you are refresh i[...]

Chapter 3 Software Configuration Page:3-6 EB-471LF USER ′ S MANUAL 3-4. LAN DRIVER UTILITY 3-4-1. Introduction EB-471LF is enhanced with LAN function t hat can support various network adapters. Installation program s for LAN drivers are lis ted as follows: 1. 2. Win 9 8/2000/X P program Linux program For more details on Installation pr ocedure, p[...]

Chapter 3 Software Configuration EB-471LF USER ′ S MANUAL Page:3-7 3-5. SOUND DRIVER UTILITY 3-5-1. Introduction The Realtek ALC202A sound function enhanced i n this system is fully compatible with Windows 98, Windows 98SE, Windows NT 4.0, Windows 2000, Windows ME and Windows XP. Below, you will find the content of the Sound driver : 1. Win 98SE [...]

Chapter 3 Software Configuration Page:3-8 EB-471LF USER ′ S MANUAL 3-6. INTEL® C HIPSET SOFTWARE INSTALLATION UTILITY 3-6-1. Introduction The Intel® Chipset Software Installatio n Utility installs to the target system the Windows* INF files that outline to the operating system how the chipset components will be confi gured. This is needed for t[...]

Chapter 3 Software Configuration EB-471LF USER ′ S MANUAL Page:3-9 3-7. USB2.0 SOFTWARE INSTALLATION UTILITY 3-7-1. Installation of Utility for Windows 98SE/ 2000/XP Intel USB 2.0 Enhanced Host Controller dri ver can only be used on Windows 98SE, Windows 2000 and Windows XP on Intel Desktop boards. It should be installe d right after the OS inst [...]

Chapter 3 Software Configuration Page:3-10 EB-471LF USER ′ S MANUAL 3-8. WATCHDOG TIMER CONFIGURATION The I/O port address of the watchdog tim er is 2E(hex) and 2F(hex). 2E (hex) is the address port. 2F(hex) is the data port . User must first assign t he address of register by writing address value into add ress port 2E(hex ), then write/read dat[...]

Chapter 3 Software Configuration EB-471LF USER ′ S MANUAL Page:3-11 Mov al, 07h ; Select Logical Device 8 of watchdog tim er Out dx,al Inc dx Mov al, 08h Out dx,al ;----------------------------------------------------------- Dec dx ; Set second as counting unit Mov al, 0f5h Out dx,al Inc dx In al,dx And al,not 08h Out dx,al ;---------------------[...]

Page: 4-1 AWARD BIOS SETUP This chapter shows how to set up the Award BIOS. Section includes: z Introduction z Entering Setup z The Standard CMOS Features z The Advanced BIOS Features z The Advanced Chipset Features z Integrated Peripherals z Power Management Setup z PNP/PCI Configurati on z PC Health Status z Frequency Control z Load Fail-Safe Def[...]

Chapter 4 Award BIOS Setup Page: 4-2 EB-471LF USER ′ S MANUAL 4-1. INTRODUCTION This chapter will show you the function o f the BIOS in managing the features of your system . The EB-471LF Celeron® M Embedded CPU Card is equipped with the B IOS for system chipset from Award Software Inc. This page briefly expl ains the function of the BIOS in m a[...]

Chapter 4 Award BIOS Setup EB-471LF USER ′ S MANUAL Page: 4-3 4-2. ENTERING SETUP When the system is powered on , the BIOS will enter th e Power-On Self Test (POST) routines and the following message will appear on the lower screen: PRESS <DEL> TO ENTER SETUP, ESC TO SKIP MEMORY TEST As long as this message i s present on the screen you may[...]

Chapter 4 Award BIOS Setup Page: 4-4 EB-471LF USER ′ S MANUAL 4-3. THE STANDARD CMOS FEATURES Highlight t he 〝 STANDARD CMOS FEATURES 〞 and press the <ENTER> key and the screen will d isplay the following tab le: Phoenix - AwardBIOS CMOS Setup Utility Standard CMOS Features Date (mm:dd:yy) Time (hh:mm:ss) Sun, Jan 5 2005 21 : 6 : 40 Ite[...]

Chapter 4 Award BIOS Setup EB-471LF USER ′ S MANUAL Page: 4-5 IDE Primary Master / Slav e: IDE Secondary Master / Slav e: The BIOS can automatically detect th e specificati ons and optimal operating mode of al most al l IDE hard drives. When you select type AUTO for a hard drive, the BIOS detect its specifica tions during POST, every time syst em[...]

Chapter 4 Award BIOS Setup Page: 4-6 EB-471LF USER ′ S MANUAL  LBA (Logical Block Addressing): During drive accesses, the IDE controller transforms the dat a address described by sector, head and cylinder number into a physical block address, significantly i mproving data transfer rates. For drives greater than 1024 cylinders. DRIVE A AND DRIV[...]

Chapter 4 Award BIOS Setup EB-471LF USER ′ S MANUAL Page: 4-7 HARD DISK ATTRIBUTES: Type Cylinders Heads V-P comp LZone Sect Capacity 1 306 4 128 305 17 10 2 615 4 300 615 17 20 3 615 6 300 615 17 30 4 940 8 512 940 17 62 5 940 6 512 940 17 46 6 615 4 65535 615 17 20 7 642 8 256 511 17 30 8 733 5 65535 733 17 30 9 900 15 65535 901 17 112 10 820 3[...]

Chapter 4 Award BIOS Setup Page: 4-8 EB-471LF USER ′ S MANUAL 4-4. THE ADVANCED BIOS FEATURES Choose the 〝 ADVANCED BIOS FEATURES 〞 in the main menu, the screen shown as below. Phoenix - AwardBIOS CMOS Setup Utility Advanced BIOS Features Item Help CPU L1 & L2 Cache Quick Power On Self Test First Boot Device Second Boot Device Boot Up Num[...]

Chapter 4 Award BIOS Setup EB-471LF USER ′ S MANUAL Page: 4-9 FIRST/SECOND/ BOOT DEVICE: The BIOS attempt to load the operating system from the devices in the sequence selected in these items. BOOT UP NUMLOCK STATUS: Select power on state for Num Lock. TYPEMATIC RATE SETTING: Enable this item if you wish to be ab le to configu re the characterist[...]

Chapter 4 Award BIOS Setup Page: 4-10 EB-471LF USER ′ S MANUAL 4-5. ADVANCED CHIPSET FEATURES Choose the 〝 ADVANCED CHIPSET FEATURES 〞 fro m th e mai n me nu , the screen shown as below. Phoenix - AwardBIOS CMOS Setup Utility Advanced Chipset Features Item Help DRAM Timing Selectable X CAS Latency Time X Active to Precharge Delay X DRAM RAS# [...]

Chapter 4 Award BIOS Setup EB-471LF USER ′ S MANUAL Page: 4-11 DRAM TIMING BY SELECTABLE: This allows you to select the DRAM timing. CAS LATENCY TIME: When synchronous DRAM i s installed, the num ber of clock cycles of CAS latency depends on the DR AM tim ing. ACTIVE TO PRECHARGE DELAY: This item controls the number of DRAM clocks for TRAS. DRAM [...]

Chapter 4 Award BIOS Setup Page: 4-12 EB-471LF USER ′ S MANUAL MEMORY HOLE AT 15M-16M: You can reserve this area of system m emory for ISA adapter ROM. Wh en this area is reserved, it cannot be cached. The user information of peripherals that need to use thi s area of system m emory usually discusses their mem ory requirements. DELAYED TRANSACTIO[...]

Chapter 4 Award BIOS Setup EB-471LF USER ′ S MANUAL Page: 4-13 4-6. INTEGRATED PERIPHERALS Choose 〝 INTEGRATED PERIPHERALS 〞 f ro m th e mai n s et up men u, a display will be shown o n screen as below: Phoenix - AwardBIOS CMOS Setup Utility Integrated Peripherals Item Help X OnChip IDE Device X Onboard Device X SuperIO Device Watch Dog Time [...]

Chapter 4 Award BIOS Setup Page: 4-14 EB-471LF USER ′ S MANUAL ONCHIP IDE DEVICE: The options for these item s are found in its sub menu. By pressing the <ENTER> key, you are prom pt to enter the sub m enu of the detailed opt ions as shown below: Phoenix – Award CMOS Setup Utility OnChip IDE Device Item Help OnChip Primary PCI IDE IDE Pri[...]

Chapter 4 Award BIOS Setup EB-471LF USER ′ S MANUAL Page: 4-15 hard drive and your system software both support Ultra DMA/33, select Auto to enable BIOS support. 4. OnChip Secondary PCI IDE Enable the secondary IDE channel. 5. IDE HDD Block Mode Block mode is also called block transfer, multiple commands, or multiple sector read/write. If your ID[...]

Chapter 4 Award BIOS Setup Page: 4-16 EB-471LF USER ′ S MANUAL This item allows you to decide to active wh ether PCI Slot o r on-chip VGA first. SUPER IO DEVICE: The options for these item s are found in its sub menu. By pressing the <ENTER> key, you are prom pt to enter the sub m enu of the detailed opt ions as shown below: Phoenix – Awa[...]

Chapter 4 Award BIOS Setup EB-471LF USER ′ S MANUAL Page: 4-17 4-7. POWER MANAGEMENT SETUP Choose 〝 POWER MANAGEMENT SETUP 〞 option on the m ain menu, a display will be shown o n screen as below : Phoenix - AwardBIOS CMOS Setup Utility Power Management Setup Power Management MODEM Use IRQ [User Define] [3] Item Help ** Reload Global Timer Eve[...]

Chapter 4 Award BIOS Setup Page: 4-18 EB-471LF USER ′ S MANUAL 4-8. PNP/PCI CONFIGURATION Choose 〝 PNP/PCI CONFIGURATION 〞 fr om t he main men u, a d is pl ay will be shown on screen as below: Phoenix - AwardBIOS CMOS Setup Utility PnP/PCI Configurations Item Help Reset Configuration Data Resources Controlled By x IRQ Resources PCI/VGA Palett[...]

Chapter 4 Award BIOS Setup EB-471LF USER ′ S MANUAL Page: 4-19 RESOURCE CONTROLLED BY: The Award Plug and Play B ios can automat ically configure all of the booth and Plug and Play-co mpatible devices. Howev er, this capability means absolutely nothing unl ess you are using a Plug and Play operating system such as Windows 95. By choosing “manua[...]

Chapter 4 Award BIOS Setup Page: 4-20 EB-471LF USER ′ S MANUAL 4-9. PC HEALTH STATUS Choose 〝 PC HEALTH STATUS 〞 from the main menu, a display will be shown on screen as below: Phoenix - AwardBIOS CMOS Setup Utility PC Health Status Item Help Current Warning Temperature Current CPU Temperature Current SYSTEM Fan Speed Vcore Vccp 3.3 V + 5 V +[...]

Chapter 4 Award BIOS Setup EB-471LF USER ′ S MANUAL Page: 4-21 4-10. FREQUENCY CONTROL Choose 〝 FREQUENCY CONTROL 〞 fr om th e ma in men u, a d is pla y will be shown on screen as below: Phoenix - AwardBIOS CMOS Setup Utility Frequency Control Item Help Auto Detect PCI Clk Spread Spectrum [Enabled] [Enabled] Menu Level ► ↑↓→← : Move[...]

Chapter 4 Award BIOS Setup Page: 4-22 EB-471LF USER ′ S MANUAL 4-11. LOAD FAIL-SAFE DEFAULTS By pressing the <ENTER> key on this item , you get a confirmation dialog box with a message si milar t o the following: Load Fail-Safe Defaults ( Y/N ) ? N To use the BIOS default values, change the prom pt to "Y" and press the <Enter &[...]

Chapter 4 Award BIOS Setup EB-471LF USER ′ S MANUAL Page: 4-23 4-13. SET SUPERVISOR PASSWORD/SET USER PASSWORD User is allowed to set eit her supervisor or user password, or both of them. The difference is that the supervisor password can ente r and change the options of the setup m enus while the user password can enter only but do not have the [...]

Chapter 4 Award BIOS Setup Page: 4-24 EB-471LF USER ′ S MANUAL 4-14. SAVE & EXIT SETUP After you have completed adjusting all the sett ings as required, you m ust remember to save these setting into the CMOS RAM. To save th e settings, select “SAVE & EXIT SETUP” and press <Enter>, a display will be shown as follows: Phoenix - Aw[...]

Chapter 4 Award BIOS Setup EB-471LF USER ′ S MANUAL Page: 4-25 4-15. EXIT WITHOUT SAVING If you wish to cancel any changes you have m ade, you may select the “EXIT WITHOUT SAVING” and the orig inal setting stored in the CMOS will be retained. The screen will be sho wn as below: Phoenix - AwardBIOS CMOS Setup Utility ► Standard CMOS Features[...]

Page: A-1 EXPANSION BUS This appendix indicates the pi n assignments. Section includes: z PC/104 Plus BUS Connector Pi n Assignment APPENDIX A[...]

Appendix A Expansion Bus Page: A-2 EB-471LF USER ′ S MANUAL PC/104 PLUS BUS CONNECTOR PIN ASSIGNMENT PC/104 Plus Bus connector is divided into four rows. Each row consists of 30 pins. The pin assignments are as followed: A B C D PIN ASSIGNMENT PIN ASSIGNMENT PIN ASSIGNMENT PIN ASSIGNMENT A1 GND B1 Reserved C1 +5V D1 AD00 A2 V/I/O B2 AD02 C2 AD01 [...]

Page: B-1 TECHNICAL SUMMARY This section introduce you the m aps concisely. Section includes: z Block Diagram z Interrupt Map z RTC & CMOS RAM Map z Timer & DMA C hannels Map z I / O & Memory M ap APPENDIX B[...]

Appendix B Technical Summary Page: B-2 EB-471LF USER ′ S MANUAL BLOCK DIAGRAM[...]

Appendix B Technical Summary EB-471LF USER ′ S MANUAL Page: B-3 INTERRUPT MAP IRQ ASSIGNMENT 0 System TIMER 1 Keyboard 2 Cascade 3 Serial port 2 4 Serial port 1 5 Available 6 Floppy 7 Parallel port 1 8 RTC clock 9 Available 10 Available 11 Available 12 PS/2 Mouse 13 Math coprocessor 14 IDE1 15 IDE2[...]

Appendix B Technical Summary Page: B-4 EB-471LF USER ′ S MANUAL RTC & CMOS RAM MAP CODE ASSIGNMENT 00 Seconds 01 Second alarm 02 Minutes 03 Minutes alarm 04 Hours 05 Hours alarm 06 Day of week 07 Day of month 08 Month 09 Year 0A Status regist er A 0B Status register B 0C Status register C 0D Status regist er D 0E Diagnostic status by te 0F Sh[...]

Appendix B Technical Summary EB-471LF USER ′ S MANUAL Page: B-5 TIMER & DMA CHANNELS MAP Timer Channel Map : Timer Channel Assignment 0 System timer interrupt 1 DRAM Refresh request 2 Speaker tone generator DMA Channel Map : DMA Channel Assignment 0 Available 1 Available 2 Floppy 3 Available 4 Cascade 5 Available 6 Available 7 Available[...]

Appendix B Technical Summary Page: B-6 EB-471LF USER ′ S MANUAL I/O & MEMORY MAP Memory Map : MEMORY MAP ASSIGNMENT 0000000-009FFFF System memory used by DOS and application 00A0000-00BFFFF Display buffer memory for VGA/ EGA / CGA / MONOCHROME adapter 00C0000-00DFFFF Reserved for I/O device BIOS ROM or RAM buffer. 00E0000-00EFFFF Reserved for[...]