Soleus Air HI1-50-03 инструкция обслуживания

HI1-50-03 © 2010 Soleus Air International HI1-50-03 Industrial Utility Heater www.sylvane.com 1-800-934-9194[...]

Thank you for choosing a Soleus Air Utility Heater . This owner ’ s manual will provide you with valuable information necessary for the proper care and maintenanc e of your ne w product. Please take a few moments to thoroughly read th e instructions and familiarize yourself with all the operational aspects of your new heater . For your own record[...]

on soft surfaces, like a bed, where openings may becom e blocked. 12. A heater has hot and arcing or sparking parts in side. DO NOT use in areas where gasoline, paint, explosive and/or flammable liquids are used or stored. Keep unit away from heated surfaces and open flames. 13. Avoid the use of an extension cord because the extension cord may over[...]

1. Use Copper wire only rated at least 60°C (140°F) 2. For supply connections use No.10 AWG or larg er wires suitable for at least 60°C (140°F) 3. Heater air flow must be directed pa rallel to, or away f rom, adjacent walls. 4. Observe wall, floor, and ceiling clearan ce requirements on DIAGRAM 1 on Page 5 of this manual. 5. Do not install clos[...]

HEA TER LOCA TION AND INST ALLA TION Install the heater out of traffic areas m aintaining the requ ired clearances be low. The direction of air flow shold not be restricted by anything and the air flow should not blow directly at exposed wa lls. When m ore than one heater is used in an area, the heater s should be arranged so that the air disc harg[...]

SPEC IFICA TIONS Voltage Rating / Amps 208/240 V / 21 Amps / Single Phase Power Consum ption 5000 Watts Unit Size 15.7 in. (W) x 11.29 i n. (D) x 14.37 in. ( H) Unit Weight 27.00 lbs. Fan CFM 270 CFM Heating BTU’s 17,100 6 www.sylvane.com 1-800-934-9194[...]

LOCA TI ON AND INST ALLA TION (CONT .) MOUNTING THE BRACKET 1. Locate a stud in the ceiling joist. 2. Remove the mounting bracket from the heat ing unit be loosening the bracket screws with a wrench and slipping the handle off over the screw heads. 3. Place a washer on the screws before inserting through the holes in the mounting bracket and screw [...]

LOCA TI ON AND INST ALLA TION (CONT .) CONNECTING THE POWER 1. Turn off the power at the main service 2. Remove the screw from t he back of the unit to connect the power to the heater. 3. Attach the cable connectors to the unit and slide the 10 gauge wire through the cable connector. NOTE : For certain applications, condui t may be required. Check [...]

OPERA TION (CONT .) ADJUSTING THE AIR FLOW DIRECTION 1. Rotating the unit - if the unit has been installed wit h a single lag bolt, simply rotate the entire unit as needed to adjust the dire ction of the air flow. 2. Tilting the unit - Loosen the bra cket screws, tilt the heater to t he desired position, and re-tighten the bracket screws. NOTE : To[...]

OPERA TION (CONT .) WIRING DIAGRAM 1. It is recommended that #10 AWG wir e be used in all installations fo r possible future reconnection at a higher wattage (Refer to t he National Electric Code (NEC) fo r maximum run length to mini- mize voltage drop to 3% max. Circuit runs e xceed 100 ft. may require larger co nductor size). 2. Wires should be r[...]

MAINTENANCE To prevent possible electric shock, disconnect t he power to the heater at the main service box be- fore attempting ins pect or clean the unit. Use care to prevent damage to the internal com ponents of the heater when cleaning the heating elem ent. Make sure all connections rem ain tight a nd all wiring is routed away from th e elem ent[...]

W ARRANTY One Year Limited Warranty Soleus International Inc. warrants the accompanying Soleus Air Heater to be free of defects i n ma terial and workman- ship for the applications specified in its operation instructi on for a period of ONE (1) year from the date of original re- tail purchase in the United States. If the unit exhibits a defect in n[...]