3M 39800 Bedienungsanleitung

Schauen Sie die Anleitung online durch oderladen Sie diese herunter
226 Seiten
1.38 mb

Download

Richtige Gebrauchsanleitung

Die Vorschriften verpflichten den Verkäufer zur Übertragung der Gebrauchsanleitung 3M 39800 an den Erwerber, zusammen mit der Ware. Eine fehlende Anleitung oder falsche Informationen, die dem Verbraucher übertragen werden, bilden eine Grundlage für eine Reklamation aufgrund Unstimmigkeit des Geräts mit dem Vertrag. Rechtsmäßig lässt man das Anfügen einer Gebrauchsanleitung in anderer Form als Papierform zu, was letztens sehr oft genutzt wird, indem man eine grafische oder elektronische Anleitung von 3M 39800, sowie Anleitungsvideos für Nutzer beifügt. Die Bedingung ist, dass ihre Form leserlich und verständlich ist.

Was ist eine Gebrauchsanleitung?

Das Wort kommt vom lateinischen „instructio”, d.h. ordnen. Demnach kann man in der Anleitung 3M 39800 die Beschreibung der Etappen der Vorgehensweisen finden. Das Ziel der Anleitung ist die Belehrung, Vereinfachung des Starts, der Nutzung des Geräts oder auch der Ausführung bestimmter Tätigkeiten. Die Anleitung ist eine Sammlung von Informationen über ein Gegenstand/eine Dienstleistung, ein Hinweis.

Leider widmen nicht viele Nutzer ihre Zeit der Gebrauchsanleitung 3M 39800. Eine gute Gebrauchsanleitung erlaubt nicht nur eine Reihe zusätzlicher Funktionen des gekauften Geräts kennenzulernen, sondern hilft dabei viele Fehler zu vermeiden.

Was sollte also eine ideale Gebrauchsanleitung beinhalten?

Die Gebrauchsanleitung 3M 39800 sollte vor allem folgendes enthalten:
- Informationen über technische Daten des Geräts 3M 39800
- Den Namen des Produzenten und das Produktionsjahr des Geräts 3M 39800
- Grundsätze der Bedienung, Regulierung und Wartung des Geräts 3M 39800
- Sicherheitszeichen und Zertifikate, die die Übereinstimmung mit entsprechenden Normen bestätigen

Warum lesen wir keine Gebrauchsanleitungen?

Der Grund dafür ist die fehlende Zeit und die Sicherheit, was die bestimmten Funktionen der gekauften Geräte angeht. Leider ist das Anschließen und Starten von 3M 39800 zu wenig. Eine Anleitung beinhaltet eine Reihe von Hinweisen bezüglich bestimmter Funktionen, Sicherheitsgrundsätze, Wartungsarten (sogar das, welche Mittel man benutzen sollte), eventueller Fehler von 3M 39800 und Lösungsarten für Probleme, die während der Nutzung auftreten könnten. Immerhin kann man in der Gebrauchsanleitung die Kontaktnummer zum Service 3M finden, wenn die vorgeschlagenen Lösungen nicht wirksam sind. Aktuell erfreuen sich Anleitungen in Form von interessanten Animationen oder Videoanleitungen an Popularität, die den Nutzer besser ansprechen als eine Broschüre. Diese Art von Anleitung gibt garantiert, dass der Nutzer sich das ganze Video anschaut, ohne die spezifizierten und komplizierten technischen Beschreibungen von 3M 39800 zu überspringen, wie es bei der Papierform passiert.

Warum sollte man Gebrauchsanleitungen lesen?

In der Gebrauchsanleitung finden wir vor allem die Antwort über den Bau sowie die Möglichkeiten des Geräts 3M 39800, über die Nutzung bestimmter Accessoires und eine Reihe von Informationen, die erlauben, jegliche Funktionen und Bequemlichkeiten zu nutzen.

Nach dem gelungenen Kauf des Geräts, sollte man einige Zeit für das Kennenlernen jedes Teils der Anleitung von 3M 39800 widmen. Aktuell sind sie genau vorbereitet oder übersetzt, damit sie nicht nur verständlich für die Nutzer sind, aber auch ihre grundliegende Hilfs-Informations-Funktion erfüllen.

Inhaltsverzeichnis der Gebrauchsanleitungen

Seite 1

3 3M-Matic  800rf T ype 39800 Automatic Random Case Sealer with AccuGlide  II T aping Heads Service Manual Printed in U.S.A. 3M Packaging Systems Division Copyright © 1999, 3M IPC. 3M Center, Building 220-8W-01 3M-Matic and AccuGlide are trademarks of 3M, All right s reserved. St. Paul, MN 55144-1000 St. Paul, MN 55144-1000 78-81[...]
Seite 2

[...]
Seite 3

T o Our Customers: This is the 3M-Matic  /AccuGlide  /Scotch  brand equipment you ordered. It has been set up and tested in the factory with Scotch brand tapes. If technical assistance or replacement part s are needed, call or Fax the appropriate number listed below . T echnical Assist ance 3M-Match  Helpline − 1-800/328 1390. P[...]
Seite 4

T o Our Customers: This is the 3M-Matic  /AccuGlide  /Scotch  brand equipment you ordered. It has been set up and tested in the factory with Scotch brand t apes. If any problems occur when operating this equipment, and you desire a ser- vice call, or phone consult ation, call, write, or Fax the appropriate number listed below. SERVIC[...]
Seite 5

3M-Matic  800rf Case Sealer Revision History Copyright  1999, 3M IPC. All rights reserved. i 3M-Matic  800rf Service Manual Revision History The original issue of this manual and subsequent revisions are identified as follows: Issue date (Rev . A): 12/98, (Rev . B): 9/99 Revision B revised pages include: Page Date T itle Page 9/99 Revision[...]
Seite 7

Section 1. Description and Specifications 1-1. Intended Use ............................................................................................................... .............................. 1-1 1-2. Description ................................................................................................................ .............[...]
Seite 8

3-17. Counter-Balance Pressure Regulator ........................................................................................ .............. 3-14 3-18. Case T op Sensitivity ...................................................................................................... ......................... 3-14 3-19. Fork Cylinder Flow Controls - Sp[...]
Seite 9

Section 6. T roubleshooting 6-1. General .................................................................................................................... ................................. 6-1 6-2. T roubleshooting Guide ...................................................................................................... .......................[...]
Seite 10

Section 8. Preventative Maintenance 8-1. General .................................................................................................................... ................................. 8-1 8-1-1. Maintenance .............................................................................................................. ................[...]
Seite 11

3M-Matic  800rf Case Sealer Safety Information Copyright  1999, 3M IPC. All rights reserved. vii W arning Label The W ARNING  Sharp Knife label, shown in Figure 1, is attached to the orange cut-off knife guard on both taping heads. The label warns the operator and service personnel of the very sharp knife located behind the guard and[...]
Seite 12

Safety Information 3M-Matic  800rf Case Sealer viii Copyright  1999, 3M IPC. All rights reserved. T ape Threading Label The T ape Threading Label, shown in Figure 3, is attached to the left side of both the upper and lower taping heads. This label provides a convenient tape threading diagram. More detailed tape loading and threading informati[...]
Seite 13

3M-Matic  800rf Case Sealer W arranty Copyright  1999, 3M IPC. All rights reserved. ix Equipment W arranty and Limited Remedy: THE FOLLOWING W ARRANTY IS MADE IN LIEU OF ALL OTHER W ARRANTIES, EXPRESS OR IMPLIED, INCLUDING , BUT NOT LIMITED TO, THE IMPLIED W ARRANTY OF MERCHANT ABILITY , THE IMPLIED W ARRANTY O F FITNESS FOR A P ARTICULAR PUR[...]
Seite 15

3M-Matic  800rf Case Sealer Description and Specifications T able of Contents 1. Description and Specifications ............................................................................................... ...................... 1-1 1-1. Intended Use ..............................................................................................[...]
Seite 17

1. Description and Specifications 1-1. Intended Use The 3M-Matic Model 800rf T ype 39800 Automatic Random Case Sealer with AccuGlide II T aping Heads is designed to accept filled, regular slotted containers from an existing conveyor , fold the top flaps, and apply a C clip of Scotch brand Pres- sure-Sensitive Film Box Sealing T ape t[...]
Seite 18

1-2. Description The 800rf Case Sealer is controlled from two operator control panels located on the front left side of the case sealer . These control panels (Electrical Control Panel and Pneumatic Control Panel) have the most-used controls within easy reach of the operator . The case sealer is microprocessor-based and firmware con- trolled to mai[...]
Seite 19

Caution Do not connect a lubricator or lubricated air to this machine. This machine has a non-lubricated air circuit. 3M-Matic  800rf Case Sealer Description and Specifications Copyright  1999, 3M IPC. All rights reserved. 1-3 1-1. Specifications T ape: 3M brand pressure-sensitive film box sealing tapes. T ape Width: Standard 3M-Matic 800r[...]
Seite 20

Description and Specifications 3M-Matic  800rf Case Sealer 1-4 Copyright  1999, 3M IPC. All rights reserved. 1-1. Case Sealing Rate Approximation Formula T o determine the case sealing rate for your application: 1. Obtain a representative sample of boxes in the proportion that will be run through the machine. Use as many boxes as necessary to[...]
Seite 21

1-1. Machine Dimensions Figure 1-2 shows machine dimensions for the 800rf Case Sealer . The dimensions are given in both inches and millimeters. For example, 20.00 inches [508 millimeters] is shown as 20.00 [508]. 3M-Matic  800rf Case Sealer Description and Specifications Copyright  1999, 3M IPC. All rights reserved. 1-5 Figure 1-2. Machine D[...]
Seite 23

3M-Matic  800rf Case Sealer Installation Copyright  1999, 3M IPC. All rights reserved. 2-i T able of Contents 2. Installation ................................................................................................................. .................................... 2-1 2-1. General ..................................................[...]
Seite 25

3M-Matic  800rf Case Sealer Installation Copyright  1999, 3M IPC. All rights reserved. 2-1 2-1. General The following instructions are presented in the order recommended for installing and setting up the 800rf Case Sealer , as well as for learning the operating functions and adjustments. Following these instruc- tions step-by-step results in [...]
Seite 26

2-2 Copyright  1999, 3M IPC. All rights reserved. 2-2. Unpacking ü Note It is the responsibility of the customer to uncrate the case sealer . Lifting equipment (forklift, overhead crane, etc.) is necessary to lift the case sealer from its pallet. The case sealer is delivered in one crate. Perform the following inspection upon receipt of the cas[...]
Seite 27

3M-Matic  800rf Case Sealer Installation Copyright  1999, 3M IPC. All rights reserved. 2-3 2-3. Setup Pr ocedure 2-3-1. Case Sealer Bed Height The legs on the case sealer can be adjusted to obtain different bed heights from the factory set-point. The bed height can be set from 25-7/8 inches [657 mm] minimum through 32 inches [815 mm] maximum.[...]
Seite 28

2-4 Copyright  1999, 3M IPC. All rights reserved. 2-3-3. W arning Beacon Installation A red warning beacon is electrically connected to the case sealer , but not mounted to the machine. Install this warning beacon on top of the frame support member to which it is connected. 1. Remove the protective wrap from the warning beacon and L-bracket asse[...]
Seite 29

3M-Matic  800rf Case Sealer Installation Copyright  1999, 3M IPC. All rights reserved. 2-5 2-3-5. Air Pressur e Indicator The Pneumatic Control Panel (Figure 2-6) is equipped with an Air Pressure Indicator to show , in red, when the air circuit is energized. The Air Pressure Indicator is located in the top center of the control panel. 2-3-6. [...]
Seite 30

2-6 Copyright  1999, 3M IPC. All rights reserved. 2-3-7. Electrical Connection Caution Before making the electrical connection, make sure that the red Latching Emergency Stop switch located on the Electrical Control Panel is depressed. Also ensure that all p ackaging materials and tools are removed from the case sealer . The case sealer and its [...]
Seite 31

3M-Matic  800rf Case Sealer Installation Copyright  1999, 3M IPC. All rights reserved. 2-7 Figure 2-7. Electrical Control Panel (T o p View) Figure 2-8. Electrical Control Panel (Front View)[...]
Seite 32

2-8 Copyright  1999, 3M IPC. All rights reserved. 2-4. T ape Loading T urn air and electrical supplies off and disconnect before servicing t aping heads. Never attempt to work on the t aping heads or load tape when the box drive system is running. Each taping head is equipped with an extremely sharp cut-off knife. Before working with the taping [...]
Seite 33

3M-Matic  800rf Case Sealer Installation Copyright  1999, 3M IPC. All rights reserved. 2-9 2-4-1. T op T ape Head Loading 1. T urn of f the Main Disconnect Switch on the Electrical Control Panel. 2. Insert the tape-threading tool downward around the rollers, as shown in Figure 2-10. Figure 2-10. Insert T ape Thr eading T ool 3. Place the tape[...]
Seite 34

2-10 Copyright  1999, 3M IPC. All rights reserved. 2-4-2. Bottom T ape Head Loading The bottom taping head is loaded and threaded in the same manner as the top taping head. For ease in loading, lift the bottom taping head from the con- veyor bed and follow the top tape head loading procedure. Refer to Figure 2-13. Figure 2-13. Bottom T aping Hea[...]
Seite 35

3M-Matic  800rf Case Sealer Installation Copyright  1999, 3M IPC. All rights reserved. 2-1 1 2-5. T ape Drum Friction Brake 1. Refer to Figure 2-14. T urn the locking nut clockwise to increase the braking force or coun- terclockwise to decrease the force. 2. Adjust the friction brake for the minimum braking force that prevents excessive overt[...]
Seite 36

2-12 Copyright  1999, 3M IPC. All rights reserved. 4. Check the Box Centering Pressure gauge on the Pneumatic Control Panel. Refer to Figure 2-15. The gauge should read 40  60 PSIG . If the pressure does not fall within this range, adjust the pressure regulator (CW  increases pressure, CCW  decreases pressure). 5. Check the Side Belt Pr[...]
Seite 37

3M-Matic  800rf Case Sealer Installation Copyright  1999, 3M IPC. All rights reserved. 2-13 8. Press the ST AR T button on the Electrical Control Panel. Refer to Figure 2-16. V erify that the side belts and the infeed rollers start turning. ü Note If pressing the ST AR T button does not result in continuous running of the side belt drive mot[...]
Seite 38

2-14 Copyright  1999, 3M IPC. All rights reserved. 10. Check the operation of the electrical interlocks for the sliding doors. W ith the drive motors running, move each sliding door , one at a time, from its closed position. V erify that the drive motors stop and that they cannot be restarted by pressing the RESET button and then the ST AR T but[...]
Seite 39

3M-Matic  800rf Case Sealer Installation Copyright  1999, 3M IPC. All rights reserved. 2-15 2-6-2. Programmable Contr oller Inputs and Outputs Figure 2-18 shows the SLC 500 Programmable Controller used in the 3M-Matic 800rf T ype 39800 Case Sealer . The Programmable Controller is located inside of the Electrical Control Panel. Figure 2-18.[...]
Seite 40

2-16 Copyright  1999, 3M IPC. All rights reserved. Figure 2-19 shows the Programmable Controller lights that turn on during the following startup conditions. Figure 2-19. Pr ogrammable Controller S tartup Conditions POWER ON RESET ST AR T POWER POWER POWER PC RUN PC RUN PC RUN INPUT 3 INPUT 0, 3, 1 1, 15 INPUT 0, 3, 1 1, 15 OUTPUT 1, 3 , 7, 12, [...]
Seite 41

3M-Matic  800rf Case Sealer Installation Copyright  1999, 3M IPC. All rights reserved. 2-17 T able 2-1 lists the INPUT LEDs displayed on the Programmable Controller , the names of the input signals that feed the LEDs, and the conditions that cause the LEDs to turn ON or OFF . V iew the LEDs with the Main Disconnect Switch and the Air On/Off V[...]
Seite 42

2-18 Copyright  1999, 3M IPC. All rights reserved. T able 2-2. Programmable Controller Outputs OUTPUT LED Output Signal Name LED Condition 0 Side Belt Lock ON when side belts lock. 1 Side Drive Motors ON when side belt drive motors are running. 2 Flap Folder Arm ON when flap folder arm is down. 3 Infeed Gate ON when infeed gate is down. 4 Center[...]
Seite 43

3M-Matic  800rf Case Sealer Installation Copyright  1999, 3M IPC. All rights reserved. 2-19 2-6-3. Dynamic T ests The following procedures check the actual operation of the 800rf Case Sealer . The following conditions must be observed. • Electrical power and compressed air are available and turned on. • The four safety doors are in their [...]
Seite 44

2-20 Copyright  1999, 3M IPC. All rights reserved. 2-7. Placing 800rf Case Sealer in P r oduction Line When installing the 800rf Case Sealer into a produc- tion line, ensure compliance with the following requirements: • The case sealer must be level. • The customer  s infeed conveyor may be powered or inclined to the case sealer . • The[...]
Seite 45

3M-Matic  800rf Case Sealer Installation Copyright  1999, 3M IPC. All rights reserved. 2-21 2-8. Special Setup Pr ocedure 2-8-1. Relocating Pneumatic and Electrical Contr ol Panels T urn off electrical power and air supply and disconnect power cord from electrical supply before beginning this procedure. Failure to comply with these warnings c[...]
Seite 46

2-22 Copyright  1999, 3M IPC. All rights reserved. 3. Disconnect the plastic conduit at the Electrical Control Panel, which connects to the Pneumatic Control Panel. This conduit contains the electri- cal wires for the valve solenoids. 4. Slide the left front sliding door all the way to the right to provide additional access. 5. Remove the Air On[...]
Seite 47

3M-Matic  800rf Case Sealer Installation Copyright  1999, 3M IPC. All rights reserved. 2-23 8. Remove the left and right mainframe brackets that support the Pneumatic Control Panel. Refer to Figure 2-24. a. Remove 8 socket-head screws (6 mm) securing the left support bracket to the case sealer (4 screws holding the bracket to the mainframe, a[...]
Seite 49

3M-Matic  800rf Case Sealer Installation Copyright  1999, 3M IPC. All rights reserved. 2-25 Installing Air On/Off V alve/Regulator/Filter 13. Locate the Air On/Off V alve/Regulator/Filter and bracket. 14. Rotate the bracket 180°. a. Remove the lower socket-head screw (4 mm) and loosen the upper screw , but do not remove it. Refer to Figure 2[...]
Seite 50

2-26 Copyright  1999, 3M IPC. All rights reserved. 16. Remove and separate the Air On/Off V alve from the Regulator/Filter . a. Loosen the hex screw in the bracket that holds the two assemblies together . Refer to Figure 2-28. b. Separate the Air On/Off V alve from the Regulator/Filter by removing both assem- blies from the bracket. 17. Rotate t[...]
Seite 51

3M-Matic  800rf Case Sealer Installation Copyright  1999, 3M IPC. All rights reserved. 2-27 19. Connect the air line from the Pneumatic Control Panel to the air outlet on the regulator body . a. Open the Pneumatic Control Panel (8 mm hex wrench) and remove the center of the left knockout grommet. b. Locate the input air line, pull it out and [...]
Seite 52

2-28 Copyright  1999, 3M IPC. All rights reserved. Removing Electrical Contr ol Panel 20. Remove the Electrical Control Panel. This step requires two people. a. Disconnect the large electrical connector and the two smaller infeed motor electrical connectors located under the Electrical Control Panel. b. Place two (2) blocks (described in S tep 6[...]
Seite 53

3M-Matic  800rf Case Sealer Installation Copyright  1999, 3M IPC. All rights reserved. 2-28 23. Remove the mainframe bracket and E-St op switch from the rear left of the machine and install the mainframe bracket at the front right of the case sealer . Refer to Figure 2-33. a. Remove 1 socket-head screw securing the E-Stop switch and bracket t[...]
Seite 54

2-30 Copyright  1999, 3M IPC. All rights reserved. 26. Connect the electrical connectors and cables to the Electrical Control Panel. a. Route the electrical connectors and cables through the undercarriage to the rear of the case sealer . b. Connect the large electrical connector and the two smaller infeed motor electrical connectors to the recep[...]
Seite 55

T able of Contents 3. Adjustments .................................................................................................................. ................................. 3-1 3-1. Case Sealer Bed Height ..................................................................................................... ................ 3-1 3-2. Pneumat[...]
Seite 56

Adjustments 3M-Matic  800rf Case Sealer 3-ii Copyright  1999, 3M IPC. All rights reserved. 3-28. Low Air Pressure Switch ................................................................................................... .............. 3-22 3-29. Overload Circuit Breaker ........................................................................[...]
Seite 57

3. 3M-Matic  800rf Case Sealer Adjustments Copyright  1999, 3M IPC. All rights reserved. 3-1 3. Adjustments 3-1. Case Sealer Bed Height Specification Adjust the case sealer bed height so that it is the same height as the conveyor line to which it is attached. Adjustment 1. Raise and support the case sealer frame to allow adequate leg adjustme[...]
Seite 58

Adjustments 3M-Matic  800rf Case Sealer 3-2 Copyright  1999, 3M IPC. All rights reserved. 3-2. Pneumatic Device Factory Set Points T able 3-1 lists the factory set points for regulator pressure controls, Pneumatic Control Panel mounted speed controls, and cylinder mounted speed controls. The table also describes the location of each adjustmen[...]
Seite 59

T able 3-1. Pneumatic Device Factory Set Points and Adjustment Locations (Continued) Cylinder Mounted Speed Controls Air Rate Exhaust Restriction Controls (Speed Controls) Set V alue Adjustment Location Infeed Gate UP 3/4 of turn CCW On Gate Cylinder  Underside of entrance end of case sealer Infeed Gate DOWN Not applicable No control device is p[...]
Seite 60

Adjustments 3M-Matic  800rf Case Sealer 3-4 Copyright  1999, 3M IPC. All rights reserved. 3-3. Main Air Pressur e Regulator Specification The case sealer requires a compressed air supply of 75  140 PSIG [5.2  9.5 BAR] 7.0 SCFM [1 1.89 m 3 /h, 21 o C, 101 kPa] maximum at maximum cycle rate. The optimum operating set point on the gauge is[...]
Seite 61

3M-Matic  800rf Case Sealer Adjustments Copyright  1999, 3M IPC. All rights reserved. 3-5 3-5. Side Belt Pr essur e Regulator Specification The side belt pressure should be set so that cases are driven smoothly through the sealing process by the belts without the cases being deformed by excessive side pressure. Caution Excessive belt wear occ[...]
Seite 62

Adjustments 3M-Matic  800rf Case Sealer 3-6 Copyright  1999, 3M IPC. All rights reserved. 3-7. Side Belts In/Out Rates This is not a r outine adjustment. Normally , it is necessary only after major disassembly or r epair of r elated components. Specification Adjust the Side Belt IN/OUT speed flow controls to allow the side belts to move to th[...]
Seite 63

3M-Matic  800rf Case Sealer Adjustments Copyright  1999, 3M IPC. All rights reserved. 3-7 3-8. Side Belt Inner Limit This is not a r outine adjustment. Normally , it is necessary only after major disassembly or r epair of r elated components. Specification W ith no box in the case sealer, adjust the side drive belt assembly inner limit reed s[...]
Seite 64

3-9. Side Belt T ension This is not a r outine adjustment. Normally , it is necessary only after major disassembly or r epair of r elated components. Specification Adjust the tension of the side belts so that the cases move through the machine positively and the belts wrap tightly around the surface of the idler pulleys at each end of the frame. W [...]
Seite 65

3-10. Motor Drive Belts, Upper and Lower This is not a r outine adjustment. Normally , it is necessary only after major disassembly or r epair of r elated components. Specification Adjust the motor drive belts to maintain proper belt tension. Adjustment W arning T urn the main air supply and electrical power off before making this adjustment. 1. Re[...]
Seite 66

3-1 1. Drive Chain This is not a r outine adjustment. Normally , it is necessary only after major disassembly or r epair of r elated components. Specification There is no exact chain tension specification. Adjust the chain so that it is just tight enough to drive reliably without slack. Adjustment Loosen three bolts, adjust the chain, and retighten[...]
Seite 67

3-13. Flap Folder Arm and Flap Folder Flow Controls - Speed Contr ols This is not a r outine adjustment. Normally , it is necessary only after major disassembly or r epair of r elated components. Specification Adjust the cylinder-mounted speed flow controls for optimum stroke operation. Consider a smooth cylinder extension and retraction without ba[...]
Seite 68

Adjustments 3M-Matic  800rf Case Sealer 3-12 Copyright  1999, 3M IPC. All rights reserved. Figure 3-15. Flap Folder Arm Reed Switch Adjustment Adjustment 1. Observe when the Flap Folder activates. It should begin to move downward when the Flap Folder Arm is about midway between fully extended and fully retracted. Refer to Figure 3- 15. 2. Loo[...]
Seite 69

3M-Matic  800rf Case Sealer Adjustments Copyright  1999, 3M IPC. All rights reserved. 3-13 3-15. Cylinder Cushion Setting ü Note This is a generic approach to adjusting the cylinder cushion settings for all cylinders used in the 800rf Case Sealer . This is not a routine adjustment. Normally , it is not necessary to adjust the cylinder cushio[...]
Seite 70

Adjustments 3M-Matic  800rf Case Sealer 3-14 Copyright  1999, 3M IPC. All rights reserved. 3-17. Counter-Balance Pr essur e Regulator Specification The Counter-Balance Pressure Regulator should be set so the upper head assembly comes to a stop between 0 and 1/8 inch from the top of the carton. Adjustment 1. Refer to Figure 3-18. Adjust the Co[...]
Seite 71

3M-Matic  800rf Case Sealer Adjustments Copyright  1999, 3M IPC. All rights reserved. 3-15 3-19. Fork Lift Flow Controls-Speed Controls These cylinder-mounted speed flow controls ar e factory set and normally do not need adjusting unless r elated components ar e r eplaced. Specification Adjust the Fork Cylinder speed flow controls so that: 1.[...]
Seite 72

Adjustments 3M-Matic  800rf Case Sealer 3-16 Copyright  1999, 3M IPC. All rights reserved. 3-20. Infeed Box S top-Gate Flow Contr ol- Speed Control This cylinder-mounted speed flow control is factory set and normally does not need adjusting unless the cylinder is replaced. Specification Adjust the Infeed Box Stop-Gate Cylinder speed flow cont[...]
Seite 73

3M-Matic  800rf Case Sealer Adjustments Copyright  1999, 3M IPC. All rights reserved. 3-17 3-21. Box Centering Rails In/Out Rates This is not a r outine adjustment. Normally , it is necessary only after major disassembly or r epair of r elated components. Specification Adjust the Box Centering IN/OUT speed flow controls to allow the centering[...]
Seite 74

Adjustments 3M-Matic  800rf Case Sealer 3-18 Copyright  1999, 3M IPC. All rights reserved. 3-22. Upper Head Assembly Down/Up Rates This is not a r outine adjustment. Normally , it is necessary only after major disassembly or r epair of r elated components. Specification Adjust the Upper Head DOWN/UP speed flow controls to allow the Upper Head[...]
Seite 75

3M-Matic  800rf Case Sealer Adjustments Copyright  1999, 3M IPC. All rights reserved. 3-19 3-23. T op Flap Compression Rollers Specification Adjust the top flap compression rollers to hold the top flaps of the case together during the taping process. The flaps should not overlap or have space between them after the taping process. Adjustment [...]
Seite 76

Adjustments 3M-Matic  800rf Case Sealer 3-20 Copyright  1999, 3M IPC. All rights reserved. 3-25. T ape Drum Friction Brake Specification Adjust the tape drum friction brake to prevent exces- sive tape overtravel caused by a flywheel effect. Adjustment 1. Refer to Figure 3-25. T urn the self-locking nut on the shaft to adjust the braking force[...]
Seite 77

3M-Matic  800rf Case Sealer Adjustments Copyright  1999, 3M IPC. All rights reserved. 3-21 3-27. One-W ay T ension Roller Specification Adjust the one-way tension roller so that it slips under a tangential force of 1 to 2 lbs. [0.5 to 0.9 kg]. Refer to Figure 3-27. Figure 3-27. One-W ay T ension Roller Adjustment Measurement 1. W rap a cord o[...]
Seite 78

Adjustments 3M-Matic  800rf Case Sealer 3-22 Copyright  1999, 3M IPC. All rights reserved. 3-28. Low Air P r essure Switch Specification Adjust the Low Air Pressure Switch so the case sealer shuts down if the main air pressure drops below 50 PSIG and a box feed is attempted. ü Note All adjustments to the Low Air Pressure Switch must be made [...]
Seite 79

3M-Matic  800rf Case Sealer Adjustments Copyright  1999, 3M IPC. All rights reserved. 3-23 3-29. Overload Circuit Br eaker Specification Adjust the setting screw on the Overload Circuit Breaker to the 1.4 Amp setting. Adjustment Use a Phillips-head screwdriver to set the alignment mark to the 1.4 Amp setting. Refer to Figure 3-29. Figure 3-29[...]
Seite 81

3M-Matic  800rf Case Sealer Disassembly/Reassembly  3M 1998 December 4-i T able of Contents 4. Disassembly/Reassembly ....................................................................................................... ....................... 4-1 4-1. General .................................................................................[...]
Seite 82

Disassembly/Reassembly 3M-Matic  800rf Case Sealer 4-ii  3M 1998 December This page intentionally left blank.[...]
Seite 83

3M-Matic  800rf Case Sealer Disassembly/Reassembly  3M 1998 December 4-1 4. Disassembly/Reassembly 4-1. General This section provides instructions for removing components and major assemblies from the Model 800rf T ype 39800 Case Sealer . Disassembly should be done only to replace a faulty part. Be sure the component is out of tolerance as de[...]
Seite 84

Disassembly/Reassembly 3M-Matic  800rf Case Sealer 4-2  3M 1998 December 4-3. Side Drive Belt Assembly T urn off the main air supply and electrical power before removing any components . W arning ![...]
Seite 85

3M-Matic  800rf Case Sealer Disassembly/Reassembly  3M 1998 December 4-3 4-4. Side Drive Belt W arning T urn off the main air supply and electrical power before removing any components . 1. Remove the side drive belt assembly using Procedure 4-3 in this section. ü Note If the side drive belt being removed is without pin and lacing, the belt [...]
Seite 86

Disassembly/Reassembly 3M-Matic  800rf Case Sealer 4-4  3M 1998 December 4-5. M otor Drive Belts, Upper and Lower T urn off the main air supply and electrical power before removing any components . ü Note A gear puller is needed to complete this procedure. Make sure a gear puller is available before begin- ning this procedure. 1. Remove the [...]
Seite 87

3M-Matic  800rf Case Sealer Disassembly/Reassembly  3M 1998 December 4-5[...]
Seite 88

Disassembly/Reassembly 3M-Matic  800rf Case Sealer 4-6  3M 1998 December 4-6. Case Sealer Bed Plates T urn off the main air supply and electrical power before removing any components . 1. Remove the side drive belt assembly using Procedure 4-3 in this section. W arning ![...]
Seite 89

3M-Matic  800rf Case Sealer Disassembly/Reassembly  3M 1998 December 4-7 4-7. Fork Cylinder ng T urn off the main air supply and electrical power before removing any component s. 1. Remove the case sealer bed plates using Procedures 4-3 and 4-6 in this section. 5. Remove the associated air lines and hardware from the cylinder . 6. Reassembly [...]
Seite 90

Disassembly/Reassembly 3M-Matic  800rf Case Sealer 4-8  3M 1998 December 4-9. Flap Folder Cylinder T urn off the main air supply and electrical power before removing any components . Steps 1 through 3 on the figure below refer to removal of the Flap Folder Cylinder . 1. Remove associated hardware, air lines, and flow control valves. 2. If a f[...]
Seite 91

3M-Matic  800rf Case Sealer Disassembly/Reassembly  3M 1998 December 4-9 4-1 1. Knife Replacement, Upper T aping Head The T ape Cut-Off Knife is very sharp. T o avoid personal injury , handle the knife with special care. Also, disconnect the power before starting this procedure. 1. Apply air pressure to the machine and raise the upper head as[...]
Seite 92

Disassembly/Reassembly 3M-Matic  800rf Case Sealer 4-10  3M 1998 December 4-12. Knife Replacement, Lower T aping Head The T ape Cut-Off Knife is very sharp. T o avoid personal injury , handle the knife with special care. Also, disconnect the power before starting this procedure. 1. Remove the lower taping head from the case sealer and lay it [...]
Seite 93

3M-Matic  800rf Case Sealer Disassembly/Reassembly  3M 1998 December 4-1 1 12. T o reassemble and reinstall the side drive belt assembly , perform steps 1 through 9 in reverse order . 13. When the side drive belt assembly has been reassembled and reinstalled, perform the follow- ing adjustment procedures described in Section 3. • Motor Driv[...]
Seite 94

Disassembly/Reassembly 3M-Matic  800rf Case Sealer 4-12  3M 1998 December 4-14. Infeed Rollers 1. Remove the photocell connectors [40] from photocells PC1 and PC2. 2. Remove the front photocell support bracket [34] secured by 3 hex-head screws. 3. Remove the Infeed front side cover [31] exposing the roller drive chain [25], roller sprockets [[...]
Seite 95

3M-Matic  800rf Case Sealer Disassembly/Reassembly  3M 1998 December 4-13[...]
Seite 96

Disassembly/Reassembly 3M-Matic  800rf Case Sealer 4-14  3M 1998 December 4-15. Overload Circuit Br eaker 1. Pull and hold down on the silver release clip located at the bottom and rear of the circuit breaker . Refer to the figure below . 2. Pull outward on the bottom of the circuit breaker and lift up and away from the DIN rail.[...]
Seite 97

3M-Matic  800rf Case Sealer Theory of Operation Copyright  1999, 3M IPC. All rights reserved. 5-i T able of Contents 5. Theory of Operation .......................................................................................................... ........................... 5-1 5-1. General ....................................................[...]
Seite 99

3M-Matic  800rf Case Sealer Theory of Operation Copyright  1999, 3M IPC. All rights reserved. 5-1 5. Theory of Operation 5-1. General This section begins with an operation summary , which gives an overview of the operations that the Model 800rf T ype 39800 Case Sealer performs as it seals a carton. Next, the sequence tables provide a detailed[...]
Seite 100

Theory of Operation 3M-Matic  800rf Case Sealer 5-2 Copyright  1999, 3M IPC. All rights reserved. During normal operation, as the box exits the case sealer it blocks the light path of the sixth photocell momentarily . When the box clears this light path, the controller allows the next box to enter the machine. If cartons accumulate on the cus[...]
Seite 101

3M-Matic  800rf Case Sealer Theory of Operation Copyright  1999, 3M IPC. All rights reserved. 5-3 T able 5-1. Sequence T able  Random Mode SEQUENCE  RANDOM MODE PLC V A L VE ACTION OUTPUT INPUT IF AIR IS ON 15 POWER IS ON POWER LIGHT IS ON TURN ON GUARDS ARE CLOSED 3 E-STO P BUTTONS ARE OFF 3 THEN PRESS RESET BUTTON 2 RESET SEQUENCE F A[...]
Seite 102

Theory of Operation 3M-Matic  800rf Case Sealer 5-4 Copyright  1999, 3M IPC. All rights reserved. T able 5-1. Sequence T able  Random Mode (continued) SEQUENCE  RANDOM MODE PLC V AL VE ACTION OUTPUT INPUT IF ST AR T BUTT ON IS PUSHED PROGRAM GOES T O STEP 1 1 STEP 1 F AST INFEED MOTOR (ROLLERS) L A TC H TURN ON 12 INFEED GA T E LA TCH ([...]
Seite 103

3M-Matic  800rf Case Sealer Theory of Operation Copyright  1999, 3M IPC. All rights reserved. 5-5 T able 5-1. Sequence T able  Random Mode (continued) SEQUENCE  RANDOM MODE PLC V AL VE ACTION OUTPUT INPUT IF T2 TIMED OUT PROGRAM GOES T O STEP 6 STEP 6 UPPER POR T X V4 VENTED 10 UPPER HEAD BRAKES X (a) V1 UNLOCK 8 LOWER POR T X (a) V3 VE[...]
Seite 104

Theory of Operation 3M-Matic  800rf Case Sealer 5-6 Copyright  1999, 3M IPC. All rights reserved. T able 5-1. Sequence T able  Random Mode (continued) SEQUENCE  RANDOM MODE PLC V AL VE ACTION OUTPUT INPUT IF PHOT OCELL PC5 IS BLOCKED PROGRAM GOES TO S TE P 9 8 STEP 9 FOLDER A RM UNLA TCH V9 MOVES UP 2 REAR FLAP FOLDER UNLA TCH V10 MO[...]
Seite 105

3M-Matic  800rf Case Sealer Theory of Operation Copyright  1999, 3M IPC. All rights reserved. 5-7 T able 5-2. Sequence T able  Fixed Mode SEQUENCE  FIXED MODE PLC V AL VE ACTION OUTPUT INPUT IF AIR IS ON 15 POWER IS ON POWER LIGHT IS ON TURN ON GUARDS ARE CLOSED 3 E-STO P BUTTONS ARE OFF 3 THEN PRESS RESET B UTT ON 2 RESET SEQUENCE F AS[...]
Seite 106

Theory of Operation 3M-Matic  800rf Case Sealer 5-8 Copyright  1999, 3M IPC. All rights reserved. T able 5-2. Sequence T able  Fixed Mode (continued) SEQUENCE  FIXED MODE PLC V AL VE ACTION OUTPUT INPUT IF ST AR T BUTT ON IS PUSHED PROGRAM GOES T O STEP 1 1 STEP 1 ST A R T T23 (0.4 SEC.) NONE T23 TIM ED OUT SIDE DRIVE ASSEMBLIES UNLA TC[...]
Seite 107

3M-Matic  800rf Case Sealer Theory of Operation Copyright  1999, 3M IPC. All rights reserved. 5-9 T able 5-2. Sequence T able  Fixed Mode (continued) SEQUENCE  FIXED MODE PLC V AL VE ACTION OUTPUT INPUT IF T2 T IMED OUT PROGRAM GOES T O STEP 6 STEP 6 SIDE DRIVE ASSEMBL Y LOCKS LA TCH V2 TURN ON 0 ST AR T T5 (15.0 SEC), CYCLE TIMER NONE [...]
Seite 109

This page intentionally left blank. 3M-Matic  800rf Case Sealer Theory of Operation Copyright  1999, 3M IPC. All rights reserved. 5-11 T able 5-3. Sequence T able  Bypass Mode SEQUENCE  BYP ASS MODE PLC V AL VE ACTION OUTPUT INPUT IF AIR IS ON 15 POWER IS ON POWER LIGHT IS ON TURN ON GUARDS ARE CLOSED 3 E-STO P BUTT ONS ARE OFF 3 THEN P[...]
Seite 110

Theory of Operation 3M-Matic  800rf Case Sealer 5-12 Copyright  1999, 3M IPC. All rights reserved. T able 5-3. Sequence T able  Bypass Mode (continued) SEQUENCE  BYP ASS MODE PLC V AL VE ACTION OUTPUT INPUT IF ST AR T BUTT ON IS PUSHED PROGRAM GOES TO STEP 1 1 STEP 1 F AST INFEED MOT OR (ROLLERS) L A TCH TURN ON 12 INFEED GA TE LA TCH ([...]
Seite 111

3M-Matic  800rf Case Sealer Theory of Operation Copyright  1999, 3M IPC. All rights reserved. 5-13 T able 5-3. Sequence T able  Bypass Mode (continued) SEQUENCE  BYP ASS MODE PLC V AL VE ACTION OUTPUT INPUT IF T2 TIMED OUT AND PHOT OCELL PROGRAM GOES PC6 IS CLEARED T O STEP 6 STEP 6 SIDE DRIVE ASSEMBL Y LOCKS LA TCH V2 TURN ON 0 ST AR T[...]
Seite 112

Theory of Operation 3M-Matic  800rf Case Sealer 5-14 Copyright  1999, 3M IPC. All rights reserved. 5-4. Electrical System When reading about the electrical system, refer to the 800rf Electrical Schematic in Subsection 5-4-3. 5-4-1. Power Distribution The Main Disconnect switch DISC 1 controls 3-phase, 208  240 V AC to the 800rf case sealer[...]
Seite 113

3M-Matic  800rf Case Sealer Theory of Operation Copyright  1999, 3M IPC. All rights reserved. 5-15 Photocells Six photocells positioned along the left side (front) of the case sealer detect the presence of boxes as they pass through the case sealer . Each photocell emits infrared light that is normally reflected back to the photocell from a r[...]
Seite 114

Theory of Operation 3M-Matic  800rf Case Sealer 5-16 Copyright  1999, 3M IPC. All rights reserved. 1-1-3. Electrical Schematic The 800rf Electrical Schematic is shown on three pages, which are labeled 1 of 3, 2 of 3, and 3 of 3. The first page contains the power distribution and motor control circuits, the safety interlocks, and the fault ind[...]
Seite 118

Theory of Operation 3M-Matic  800rf Case Sealer 5-20 Copyright  1999, 3M IPC. All rights reserved. 5.5 Pneumatic System When reading about the pneumatic system, refer to the 800rf Pneumatic Diagram on the next page. The main feature of the pneumatic system used in the 800rf case sealer is that all of the directional control valves are solenoi[...]
Seite 119

3M-Matic  800rf Case Sealer T roubleshooting Copyright  1999, 3M IPC. All rights reserved. 6-i T able of Contents 6. T roubleshooting .............................................................................................................. ............................... 6-1 6-1. General ..................................................[...]
Seite 121

3M-Matic  800rf Case Sealer T roubleshooting Copyright  1999, 3M IPC. All rights reserved. 6-1 6-1. General Read the Theory of Operation in Section 5, so that the operational characteristics of the machine are understood. Additionally , refer to Pneumatic Component T esting and Electrical Fault Conditions at the end of this section along with[...]
Seite 122

Problem Cause Correction Box rear flap pulled back out of box. Rear flap folder out of adjustment. Adjust Rear Flap Folder (refer to Section 3). Flaps not positioned properly before entering case sealer . Position flaps properly . Front of box crushed by upper Paddle is not returning after Adjust Paddle Pressure Regulator head assembly . previous b[...]
Seite 123

3M-Matic  800rf Case Sealer T roubleshooting Copyright  1999, 3M IPC. All rights reserved. 6-3 Problem Cause Correction Blade does not cut tape or tape end Adhesive has built up on blade. Clean blade. is jagged or shredded. (continued) Cutoff force is not sufficient. Install an additional cutoff spring. Cutoff blade is dry . Lubricate blade o[...]
Seite 124

T roubleshooting 3M-Matic  800rf Case Sealer 6-4 Copyright  1999, 3M IPC. All rights reserved. Problem Cause Correction T ape end does not stay in T ape is threaded incorrectly . Rethread tape. application position in front of applying roller . Flanged knurled roller overruns on Adjust one-way tension roller in its return of applying mechanis[...]
Seite 125

3M-Matic  800rf Case Sealer T roubleshooting Copyright  1999, 3M IPC. All rights reserved. 6-5 Problem Cause Correction T ape edge folds over, providing an T ape drum is not aligned. Adjust T ape W eb Alignment unsatisfactory seal. (refer to Section 3). T ape roll is telescoped. Replace tape roll. T ape drum bracket is bent. S traighten[...]
Seite 126

T roubleshooting 3M-Matic  800rf Case Sealer 6-6 Copyright  1999, 3M IPC. All rights reserved. 6-3. Pneumatic Component T esting Using the solenoid actuated valves, located in the Pneumatic Control Panel, you can manually actuate the valves that initiate the operation of other pneumatic components within the Model 800rf Case Sealer . The valv[...]
Seite 127

3M-Matic  800rf Case Sealer T roubleshooting Copyright  1999, 3M IPC. All rights reserved. 6-7 The following table lists the pneumatic valves and describes the function of each valve. T o avoid injury to yourself or others, never actuate a pneumatic valve unless everyone is clear of the machine. Also all tools and cartons must be away from th[...]
Seite 128

T roubleshooting 3M-Matic  800rf Case Sealer 6-8 Copyright  1999, 3M IPC. All rights reserved. 6-4. Electrical Cir cuit Fault Conditions The Model 800rf Case Sealer displays electrical circuit fault conditions on the Electrical Control Panel with red light indicators along with a red beacon light on a light pole. The following table lists the[...]
Seite 129

3M-Matic  800rf Case Sealer Illustrated Parts Breakdown Copyright  1999, 3M IPC. All rights reserved. 7-i T able of Contents 7. Illustrated Parts Br eakdown .................................................................................................. ...................... 7-1 7-1. How to Order Replacement Parts .........................[...]
Seite 130

Illustrated Parts Breakdown 3M-Matic  800rf Case Sealer 7-ii Copyright  1999, 3M IPC. All rights reserved. Figure 7-28. Applying Assembly for Upper and Lower Heads ................................................ 7-74 Figure 7-29. Buffing Assembly for Upper Head ...................................................................... 7-76 Figur[...]
Seite 131

7. Illustrated Parts Breakdown 7-1. How to Order Replacement Parts 1. Refer to the following figures and their related lists of parts on the following pages to determine the individual part number and description. ü Note Complete descriptions have been included for most commercially available components. This will allow the customer/service person[...]
Seite 135

Parts List - Conveyor Frame Item Part Number Number Description Qty 1 ................ 78-8119-8588-2 ............ BED ASSEMBL Y , Conveyor .............................................................. ......... 1 2 ................ 78-8076-5038-3 ............ LEG ASSEMBL Y , Right ..................................................................[...]
Seite 136

Parts List - Conveyor Frame (Continued) Item Part Number Number Description Qty 67 .............. 78-8060-7873-5 ............ PLUG , Female ......................................................................... ...................... 2 68 .............. 78-8028-8208-0 ............ SCREW , 6P x 9,5 ................................................[...]
Seite 139

Parts List - Conveyor Center Bed and Fork Item Part Number Number Description Qty 15 .............. 26-1003-7963-0 ............ SCREW , Soc. Hd., M8 x 16 ............................................................. .......... 10 18 .............. 78-8017-9318-9 ............ W ASHER, Plain, Metric, 8mm ..............................................[...]
Seite 141

Parts List - Conveyor Bed Rollers Item Part Number Number Description Qty 41 .............. 78-80178060-92577803-92 SCREW , Phillips Head, M4 x 10RIVET .............................................. 20 42 .............. 26-1003-6914-4 ............ NUT , Plastic Insert, M4 .............................................................. ..............[...]
Seite 143

Parts List - Side Belt Centering Item Part Number Number Description Qty 1 ................ 78-8114-4867-5 ............ ARM ASSEMBL Y , Front, Right .......................................................... ........ 1 2 ................ 78-8114-4868-3 ............ ARM ASSEMBL Y , Front, Left ........................................................[...]
Seite 144

Parts List - Side Belt Centering (Continued) Item Part Number Number Description Qty 34 .............. 78-8060-7533-5 ............ LOCK RING ............................................................................ ..................... 2 35 .............. 78-8114-5095-2 ............ BUSHING , Cylinder ...........................................[...]
Seite 147

Parts List - Column Assembly Item Part Number Number Description Qty 1 ................ 78-8114-5096-0 ............ COLUMN ASSEMBL Y , Right ..................................................................... 1 2 ................ 78-8114-5097-8 ............ COLUMN ASSEMBL Y , Left ..................................................................[...]
Seite 149

Parts List - Flap Folder Assembly Item Part Number Number Description Qty 1 ................ 78-8119-8502-3 ............ SUPPOR T , Flap Folder ................................................................ ................. 1 2 ................ 26-1003-7963-0 ............ SCREW , Soc. Hd., M8 x 16 ................................................[...]
Seite 150

Parts List - Flap Folder Assembly (Continued) Item Part Number Number Description Qty 34 .............. 78-8060-7896-6 ............ SCREW , Soc. Hd., Hex Hd., M6 x 14 .......................................................... 2 35 .............. 78-8060-7885-9 ............ CAP , End ..................................................................[...]
Seite 153

Parts List - Paddle Assembly Item Part Number Number Description Qty 1 ................ 78-8119-8507-2 ............ SUPPOR T ASSEMBL Y , Guide, Right ...................................................... ... 1 2 ................ 78-8119-8508-0 ............ SUPPOR T ASSEMBL Y , Guide, Left ....................................................... ...[...]
Seite 155

Parts List - Side Belt Rail Assembly Item Part Number Number Description Qty 1 ................ 78-8114-4904-6 ............ SIDE FLAP FOLDER, Right ............................................................. .......... 1 2 ................ 78-8076-5083-9 ............ SIDE FLAP FOLDER, Left .........................................................[...]
Seite 157

Parts List - Head Cylinder Assembly Item Part Number Number Description Qty 1 ................ 78-8057-5747-9 ............ MOUNT , Cylinder Rod End ......................................................................... 2 2 ................ 26-1003-6918-5 ............ NUT , Plastic Insert, Hex, M10 ................................................[...]
Seite 159

Parts List - Upper T ape Head Mount Item Part Number Number Description Qty 1 ................ 78-8122-6717-3 ............ FRAME, Right, Upper Head, w/English Label ........................................... .1 2 ................ 78-8122-6718-1 ............ FRAME, Left, Upper Head, w/English Label ............................................ .. 1 [...]
Seite 161

Parts List - Up per T ape Drum Bracket Assembly Item Part Number Number Description Qty 1 ................ 78-8094-6446-0 ............ BRACKET ASSEMBL Y , Core Holder ....................................................... .. 1 2 ................ 78-8091-0605-3 ............ BRACKET , Core Holder .....................................................[...]
Seite 163

Parts List - Side Belt and Drive Assemblies Item Part Number Number Description Qty 1 ................ 78-8119-8513-0 ............ DRIVE ASSEMBL Y , Side, Right, w/o Motor .............................................. 1 2 ................ 78-8119-8514-8 ............ DRIVE ASSEMBL Y , Side, Left, w/o Motor ..........................................[...]
Seite 164

Parts List - Side Belt and Drive Assemblies (Continued) Item Part Number Number Description Qty 64 .............. 78-8094-6472-6 ............ MOT OR, 200/220V , 50/60Hz ....................................................................... 2 65 .............. 78-8076-5226-4 ............ F AN, Motor , F .63 .........................................[...]
Seite 167

Parts List - Side Belt Drive Pulleys (Detail) Item Part Number Number Description Qty 15 .............. 78-8060-8000-4 ............ DRIVE PULLEY ASSEMBL Y ................................................................ .... 2 16 .............. 78-8076-5105-0 ............ PULLEY ASSEMBL Y , Drive ....................................................[...]
Seite 169

Parts List - Upper Head Conduit Assembly Item Part Number Number Description Qty 1 ................ 78-8100-0897-5 ............ HOUSING , W ire ....................................................................... .................... 1 2 ................ 26-1003-7963-0 ............ SCREW , Soc. Hd., M8 x 16 ......................................[...]
Seite 171

Parts List - Electrical Control Panel Item Part Number Number Description Qty 1 ................ 78-8122-6719-9 ............ BOX, Electric w/English Label ....................................................... ............. 1 2 ................ 78-8119-8591-6 ............ HINGE, Southco E6, 10, 501, 20 .............................................[...]
Seite 172

Parts List - Electrical Control Panel (Continued) Item Part Number Number Description Qty 34 .............. 78-8076-5123-3 ............ PLUG , CNE 24FSN ...................................................................... ................ 1 35 .............. 78-8060-7872-7 ............ COVER, Plug S traight .......................................[...]
Seite 175

Parts List - Electrical Control Panel (Detail) Item Part Number Number Description Qty 1 ................ 78-8100-0898-3 ............ SWITCH ASSEMBL Y , LA2-16 ................................................................... 1 2 ................ 78-8060-7622-6 ............ FUSE CARRIER ............................................................[...]
Seite 177

Parts List - Pneumatic Contr ol Panel Item Part Number Number Description Qty 1 ................ 78-8122-6721-5 ............ BOX, Pneumatics w/English Label .............................................................. 1 2 ................ 78-8119-8554-4 ............ ADHESIVE, Rubber Seal ...........................................................[...]
Seite 179

Parts List - Pneumatic Components, #1 Item Part Number Number Description Qty 1 ................ 78-8119-8605-4 ............ FIL TER/REGULA T OR ASSEMBL Y ........................................................... 1 10 .............. 78-8119-8612-0 ............ SOLENOID V AL VE ASSEMBL Y ............................................................[...]
Seite 181

Parts List - Pneumatic Components, #2 Item Part Number Number Description Qty 47 .............. 78-8091-0350-6 ............ UNION, Special ....................................................................... ..................... 8 48 .............. 78-8076-4666-2 ............ ELBOW , Bulkhead ....................................................[...]
Seite 183

Parts List - Pneumatic Components, #3 Item Part Number Number Description Qty 1 ................ 78-8119-8605-4 ............ FIL TER/REGULA T OR ASSEMBL Y ........................................................... 1 2 ................ 78-8119-8606-2 ............ REGULA TOR, Pressure, SMC, EA W3000 ..................................................[...]
Seite 184

Parts List - Pneumatic Components, #3 (Continued) Item Part Number Number Description Qty 37 .............. 78-8119-8632-8 ............ GAUGE, 50, 0-12 Bar .................................................................. ................ 3 38 .............. 78-8119-8633-6 ............ UNION, 31 140413 .............................................[...]
Seite 185

Parts List - Pneumatic Components, #3 (Continued) Item Part Number Number Description Qty 77 .............. 78-8119-8659-1 ............ SIDE DRIVE, Air Cylinder Assembly .................................................... ..... 1 78 .............. 78-8119-8660-9 ............ CYLINDER, Air , SMC, C95SD, B63, 100 ....................................[...]
Seite 187

Parts List - Sliding Door Assembly Item Part Number Number Description Qty 1 ................ 78-8119-8568-4 ............ FRAME, Right, Guards ................................................................ ................ 1 2 ................ 78-8119-8670-8 ............ FRAME, Left, Guards ........................................................[...]
Seite 188

Parts List - Sliding Door Assembly (Continued) Item Part Number Number Description Qty 34 .............. 78-8010-7416-8 ............ NUT , Metric, Hex, S teel, M4 .......................................................... ............. 2 35 .............. 78-8076-4532-6 ............ CORD GRIP ........................................................[...]
Seite 191

3M-Matic  800rf Case Sealer Illustrated Parts Breakdown Copyright  1999, 3M IPC. All rights reserved. 7-61 Parts List - Infeed Conveyor Frame Item Part Number Number Description Qty 1 ................ 78-8114-4812-1 ............ CONVEYER FRAME ASSEMBL Y ............................................................ 1 2 ................ 78-8076-[...]
Seite 192

Illustrated Parts Breakdown 3M-Matic  800rf Case Sealer 7-62 Copyright  1999, 3M IPC. All rights reserved. Parts List - Infeed Conveyor Frame (Continued) Item Part Number Number Description Qty 34 .............. 78-8114-4823-8 ............ SUPPOR T , Photocell/Reflector ......................................................... ........... 2 3[...]
Seite 195

3M-Matic  800rf Case Sealer Illustrated Parts Breakdown Copyright  1999, 3M IPC. All rights reserved. 7-65 Parts List - Infeed Conveyor Drive Assembly Item Part Number Number Description Qty 1 ................ 78-8114-4827-9 ............ GEARBOX, NMR V40, i20, P AM63, B5 ..................................................... 1 2 ..............[...]
Seite 197

3M-Matic  800rf Case Sealer Illustrated Parts Breakdown Copyright  1999, 3M IPC. All rights reserved. 7-67 Parts List - Infeed Conveyor Centering Assembly Item Part Number Number Description Qty 1 ................ 78-81 14-4837-8 ............ BOX ................................................................................. ...............[...]
Seite 198

Illustrated Parts Breakdown 3M-Matic  800rf Case Sealer 7-68 Copyright  1999, 3M IPC. All rights reserved. Parts List - Infeed Conveyor Centering Assembly (Continued) Item Part Number Number Description Qty 34 .............. 78-8054-8779-6 ............ CAP , End .................................................................................[...]
Seite 203

3M-Matic  800rf Case Sealer Illustrated Parts Breakdown Copyright  1999, 3M IPC. All rights reserved. 7-73 Parts List  Frame Assembly for Upper Head Item Part Number Number Description Qty 1 ................ 78-8070-1386-3 ............ FRAME, T ape Mount Upper Assembly .................................................... ... 1 2 ..........[...]
Seite 205

3M-Matic  800rf Case Sealer Illustrated Parts Breakdown Copyright  1999, 3M IPC. All rights reserved. 7-75 Parts List  Applying Assembly for Upper and Lower Heads Item Part Number Number Description Qty 1 ................ 78-8070-1206-3 ............ APPL YING ARM #1 ..................................................................... ....[...]
Seite 207

3M-Matic  800rf Case Sealer Illustrated Parts Breakdown Copyright  1999, 3M IPC. All rights reserved. 7-77 Parts List  Buffing Assembly for Upper Head Item Part Number Number Description Qty 1 ................ 78-8070-1392-1 ............ BUFFING ARM, Sub Assembly ........................................................... ....... 1 2 .....[...]
Seite 209

3M-Matic  800rf Case Sealer Illustrated Parts Breakdown Copyright  1999, 3M IPC. All rights reserved. 7-79 Parts List  Link Assembly for Upper and Lower Heads Item Part Number Number Description Qty 1 ................ 78-8070-1388-9 ............ LINK, Arm Bushing Assembly .......................................................... .........[...]
Seite 211

3M-Matic  800rf Case Sealer Illustrated Parts Breakdown Copyright  1999, 3M IPC. All rights reserved. 7-81 Parts List  Knife Assembly for Upper and Lower Heads Item Part Number Number Description Qty 1 ................ 78-8070-1217-0 ............ FRAME, Cut-Off W eldment .....................................................................[...]
Seite 213

3M-Matic  800rf Case Sealer Illustrated Parts Breakdown Copyright  1999, 3M IPC. All rights reserved. 7-83 Parts List  T ape Drum and Bracket for Upper and Lower Heads Item Part Number Number Description Qty 1 ................ 78-8070-1395-4 ............ BRACKET , Bushing Assembly ...........................................................[...]
Seite 215

3M-Matic  800rf Case Sealer Illustrated Parts Breakdown Copyright  1999, 3M IPC. All rights reserved. 7-85 Parts List  Frame Assembly for Lower Head Item Part Number Number Description Qty 1 ................ 78-8070-1369-9 ............ FRAME, T ape Mount Lower Assembly .................................................... ... 1 2 ..........[...]
Seite 217

3M-Matic  800rf Case Sealer Illustrated Parts Breakdown Copyright  1999, 3M IPC. All rights reserved. 7-87 Parts List  Buffing Assembly for Lower Head Item Part Number Number Description Qty 1 ................ 78-8070-1391-3 ............ BUFFING ARM SUB ASSEMBL Y ............................................................ .1 2 ...........[...]
Seite 219

T able of Contents 8. Pr eventative Maintenance ............................................................................................................................ 8-1 8-1. General .................................................................................................................... ........................... 8-1 8-1-1. Main[...]
Seite 221

3M-Matic  800rf Case Sealer Preventative Maintenance Copyright  1999, 3M IPC. All rights reserved. 8-1 8. Preventative Maintenance 8-1. General The Model 800rf Case Sealer is designed for long, trouble-free service. 8-1-1. Maintenance The machine performs best when it receives routine maintenance and cleaning. Machine components that fail or [...]
Seite 222

Pr eventative Maintenance 3M-Matic  800rf Case Sealer 8-2 Copyright  1999, 3M IPC. All rights reserved. 8-3. Lubrication Like most other equipment, the case sealer must be lubricated periodically to ensure long, trouble-free service. Most of the machine bearings are perma- nently lubricated and sealed and do not need further lubrication. The [...]
Seite 223

3M-Matic  800rf Case Sealer Preventative Maintenance Copyright  1999, 3M IPC. All rights reserved. 8-3 2. Side Belt Drive Assembly At 250 hours, use multipurpose grease. • Lightly coat chain pitches (Figure 7-13, # 75). 3. Column Assembly At 250 hours, use multipurpose grease. • Lightly coat outside surface of the column guides (Figure 7-[...]
Seite 224

Pr eventative Maintenance 3M-Matic  800rf Case Sealer 8-4 Copyright  1999, 3M IPC. All rights reserved. 8-4. Maintenance Schedule 1-1-1. T aping Heads The following table provides recommendations for inspecting and replacing parts, and cleaning and lubricating the upper and lower taping heads. T aping Head Inspect/Replace Clean Lubricate Coun[...]
Seite 225

3M-Matic  800rf Case Sealer Preventative Maintenance Copyright  1999, 3M IPC. All rights reserved. 8-5 8-4-3. Main Assembly The following table provides recommendations for inspecting and replacing parts, and cleaning and lubricating the main assembly . Main Assembly Inspect/Replace Clean Lubricate Counter Cycles * Side Drive Belts Inspect at[...]

3M 39800 Bedienungsanleitung

Ähnliche Gebrauchsanleitungen

Food Saver

3M 200a

Food Saver

3M 40800

Food Saver

3M 800af-s

Food Saver

3M 800a3

Food Saver

3M 18900

Food Saver

3M 39600

Food Saver

3M 800rks

Food Saver

3M 40800

Richtige Gebrauchsanleitung

Was ist eine Gebrauchsanleitung?

Was sollte also eine ideale Gebrauchsanleitung beinhalten?

Warum lesen wir keine Gebrauchsanleitungen?

Warum sollte man Gebrauchsanleitungen lesen?

Inhaltsverzeichnis der Gebrauchsanleitungen

Seite 1

Seite 2

Seite 3

Seite 4

Seite 5

Seite 6

Seite 7

Seite 8

Seite 9

Seite 10

Seite 11

Seite 12

Seite 13

Seite 14

Seite 15

Seite 16

Seite 17

Seite 18

Seite 19

Seite 20

Seite 21

Seite 22

Seite 23

Seite 24

Seite 25

Seite 26

Seite 27

Seite 28

Seite 29

Seite 30

Seite 31

Seite 32

Seite 33

Seite 34

Seite 35

Seite 36

Seite 37

Seite 38

Seite 39

Seite 40

Seite 41

Seite 42

Seite 43

Seite 44

Seite 45

Seite 46

Seite 47

Seite 48

Seite 49

Seite 50

Seite 51

Seite 52

Seite 53

Seite 54

Seite 55

Seite 56