Advantech AIMB-760 Bedienungsanleitung

AIMB-760 Socket LGA 775 Intel® Pentium® 4 / Celeron® D 800 MHz FSB Industrial A TX Motherboard with PCI-E/DDR2/Dual GbE User Manual[...]

AIMB-760 User Manual ii Copyright This document is copyrighted, 2006, by Advan tech Co., Ltd. All rights are reserved. Advantech Co ., Ltd. reserves the right to make improve- ments to the products descri bed in this manual at any time withou t notice. No part of this m anual may be repro duced, copied, transl ated or transmit- ted in any form or b[...]

iii A Message to the Customer Advantech Customer Services Each and every Advantech pro duct is built to the most exacting specifica- tions to ensure reliable perform ance in the harsh and demanding condi- tions typical of industrial environm ents. Whether your new Advantech equipment is destined for the laborato ry or the factory floor , you can be[...]

AIMB-760 User Manual iv Certifications This device complies with the requirements in part 15 of the FCC rules: Operation is subject to the following two con ditions: • This device may not cause harmful interference • This device must accept any interfe r ence received, including interfer- ence that may cause undesired operation This equipment h[...]

v Memory Compatibil ity Network Feature Comparison T able 1.1: AIMB-760 Memory T ested for Compatibility Brand Size Speed T ype Memo ry Apacer 1 GB DDR2 533 DDR2 SAMSUNG K4T51083QB-ZKD5 UG 512 MB DDR2 4 00 DDR2 4WB42 D9CHL 1 GB DDR2 400 DDR2 ELPIDA E5108AB-5C-E T ranscend 256 MB DDR2 5 33 DDR2 SAMSUNG 443 K4T56083QF-GC05 512 MB DDR2 5 33 DDR2 ELPID[...]

AIMB-760 User Manual vi Product warran ty Advantech warrants to you, the original purchaser , that each of its prod- ucts will be free from defects in material s and workmanshi p for two years from the date of purchase. This warranty does not apply t o any products which have b een repaired or altered by persons other than repair perso nnel authori[...]

vii Initial Inspection Before you begin installing your mot herboard, please make sure that the following materi als have been shipp ed: If any of these items are missing or damaged, contact your distributor or sales representative immediately . W e have carefully inspected the AIMB- 760 mechanically and electrically befo re shipment. It should b e[...]

AIMB-760 User Manual viii[...]

ix Contents Chapter 1 Hardware Co nfiguration ................................. 2 1.1 Introduction ............ ............................ ............ ........... ........ 2 1.2 Features ............. ................... ....................... ...................... 3 1.3 Specifications ............ ....................... .....................[...]

AIMB-760 User Manual x 2.5 USB Ports (CN6, CN63, CN31, CN32) .............. ............ 20 Figure 2.1:USB Port s ...... ........... ............. ........... ........... 20 2.6 VGA Connector (CN7) ................. ...................... ............ 21 2.7 Serial Ports (COM1:CN9; COM2:CN10) .................... ... 21 2.8 PS/2 Keyboard and Mouse [...]

xi 3.4 Advanced BIOS Features ................. ...................... ......... 39 Figure 3.3:Advanced BI OS features screen ....... ........... 39 3.4.1 CPU Fea tures ....... ........... ........... ........... ........... ........... .. 39 3.4.2 Hard Disk Boot Priority ........... ........... ........... ............. .. 40 3.4.3 Vi rus Warning.[...]

AIMB-760 User Manual xii 3.6.7 SAT A Port .... ......... ........... ........... ........... ........... ........... 46 Figure 3.7:Onboard Devi ce............ ............ ........... ........ 47 3.6.8 USB Cont roller ............... ........... ........... ........... ........... .. 47 3.6.9 USB 2.0 Controll er .. ........... ........... .........[...]

xiii 3.8.2 Res ources Controlled By ......... ........... ........... ........... .... 53 3.8.3 PCI/VGA Palette Snoop ................ ............ ........... ........ 53 3.8.4 Ma ximum Payload Size ............... ........... ........... ........... 53 3.9 PC Health Status.............. ................... ....................... ...... 54 Figure[...]

AIMB-760 User Manual xiv A.1.4 Example Program ............. ........... ........... ........... ........... 85 Appendix B Pin Assignments ............................................. 92 B.1 IDE Hard Drive Connector (CN1) ...................... ............ 92 B.2 Floppy Drive Connector (CN3).......... ....................... ...... 93 B.3 Paralle[...]

1 CHAPTER 1 General Information[...]

AIMB-760 User Manual 2 Chapter 1 Hardware Configuration 1.1 Introduction Advantech's AIMB-760 is designed with the Intel 915GV and ICH6 PCI Express chipset in an A T X form factor . Not only does it boast commer- cial PC performance but it also has in dustrial features such as reliability , longevity , revision control and scalability . This p[...]

3 1.2 Features • PCI Express ar chitecture: Designed with the Intel 915GV an d ICH6 PCI-Express chipset, the AIMB-760 has dual/single Gigabit LAN via PCI-E x1 bus and 2 PCI-E x1 slots (one for riser card). • High Performance I/O Capability: Dual/single Gigabit LAN via PCI- E x1 bus, 2 PCI-E x1 slots (one for riser card), 5 PCI 32-bit /33MHz PCI[...]

AIMB-760 User Manual 4 . • L2 Cache: CPU has built-in 1024KB/2048KB KB fu ll-speed L2 cache (for Pentium 4 CPU) / 256/51 2 KB (For Celeron D CPU) • BIOS: A ward Flash BIOS (4Mb Flash Memory) • System Chipset: Intel 915GV with ICH6 • SA T A/EIDE hard disk drive interface: Four on-board Seri al A T A connectors with data transmission rate up [...]

5 • Enhanced parallel port: Configured to LP T1, LP T2, LP T3, or dis- abled. Standard DB-25 female connector p rovided. Supports EPP/SPP/ ECP • Serial ports: T wo RS-232 ports with one DB-9 connector and one on- board pin header for ex tension. Supporting speeds up t o 1 15.2 Kbp s. Ports can be individually configured to COM1, COM2 , or disab[...]

AIMB-760 User Manual 6 1.4 Jumpers and Connectors Connectors on the AIMB-760 moth erboard link it to external devices such as hard disk drives and a keyboard. In addition , the board has a num- ber of jumpers used to configure your system for your app lication. The tables below list the function of each of the board jumpers and con- nectors. Later [...]

7 CN22 HW Monitor Alarm Close: Enable OBS Alarm Open: Disable OBS Alarm CN29 SM BUS Connector PIN1: SMB_DA T A PIN2: SMB_CLOCK CN31 USB port 0, 1 & LAN1 CN32 USB port 2, 3 & LAN2 CN37 System F AN connector 2 CN55 Line Out, Mic IN connector CN56 CD IN (Audio input from CD-ROM) CN57 AUX IN connector CN59 Front panel audio connector CN62 8-pin[...]

AIMB-760 User Manual 8 1.5 Board Layout: Jumper and Connector Locations Figure 1.1: Jumper and Connector locations[...]

9 Figure 1.2: I/O Connecto rs CN11 CN4 CN9 CN7 CN55 CN31 CN32[...]

AIMB-760 User Manual 10 1.6 AIMB-760 Block Diagram Figure 1.3: AIMB-760 Block Diagram 915GV GMCH CRT 1 ATA 100 port 4 SATA ports 8 USB Ports LGA775 Processor Audio Codec BIOS Super IO Winbond W83627H F G- LAN1 : B roadcom BCM5721 Dir ect M edi a Inte rfa ce 2GB /s band wid th ICH6 5 3 3 / 8 0 0 M H z F S B 150MB/s PCI- Expr ess x1 DMA 33/66/1 00 U [...]

11 1.7 Safety Precautions War ni n g! Always completely disc onne ct the powe r cord from your chassis whenever you work with the hardware. Do not make conne ctions while the power is on. Sensitive electronic component s can be damaged by sudden power surges. Only experience d electronics personne l should open the PC chassis. Caution! Always gr ou[...]

AIMB-760 User Manual 12 1.8 Jumper Setti ngs This section provides i nstructions on how to configu re your motherboard by setting the jumpers. It also includes the motherboards's de fault settings and your options for each jumper . 1.8.1 How to set jumpers Y ou can configure your motherboard to match the needs of your applica- tion by settin g[...]

13 1.8.3 W atchdog timer output (J2) The AIMB-760 cont ains a watchdog timer th at will reset the CPU or send a signal to IRQ1 1 in the event the CPU stops processi ng. This feature means the AIMB-760 will recover from a software failure or an EMI problem. Th e J2 jumper settings c ontrol the outcome of what the com- puter will do in the event the [...]

AIMB-760 User Manual 14 1.9 System Memory The AIMB-76 0 has four sockets for 240-pin dual inline memory mo dules (DIMMs) in two memory channels. All these sockets use 1.8 V unbuffered double data rate synchronous DRAMs (DDR SDRAM). They are ava ilable in capacities of 256, 512 and 1024 MB. The so ckets can be filled in any combination with DIMMs of[...]

15 1.12 Processor Installation The AIMB-76 0 is designed for Intel Pentiu m® 4 processor / Celeron® D (LGA 775 socket) up to 3.8/3.06 GHz. Step 1: Pull the bar besides the CPU socket outward and lift it. Step 2: Align the triangular markin g on the processor with the cut edge of the socket.[...]

AIMB-760 User Manual 16 Step 3: Put back the socket cap and press down the bar to fix it. 1.13 PCI Bus Routing T able T able 1.6: PCI Bus Routing T able PCI Slot ID SEL PCI Interrupt PCI1 AD31 INT B, C, D, A PCI2 AD30 INT C, D, A, B PCI3 AD29 INT D, A, B, C PCI4 AD28 INT A, B, C, D PCI5 AD27 INT B, C, D, A T able 1.7: 1U PCI Riser Card PCI Bus Rout[...]

17 Chapter 2 CHAPTER 2 Connecting Peripherals[...]

AIMB-760 User Manual 18 Chapter 2 Connecting Peripherals 2.1 Introduction Y ou can access most of the connectors fr om the top of the board while it is installed in the chassis. If you have a number of cards installed or have a packed chassis, you may need to partially remove the card to make all the connections. 2.2 Primary (CN1) IDE Connector Y o[...]

19 Chapter 2 labeled on the drive circuit board. Check the documentation that came with the drive fo r more information. 2.3 Floppy Drive Connector (CN3) Y ou can attach up to two floppy disk drives to the AIMB -760's onboard controller . Y ou can use 3.5" (720 KB, 1.44 MB) drives. The motherboard comes wi th a 34-pin daisy-chai n drive c[...]

AIMB-760 User Manual 20 2.4 Parallel Port (CN4) The parallel port is normally used to connect the motherboard to a printer . The AIMB-760 includes an onboard pa rallel port, accessed through a 26- pin flat-cable connector , CN4. 2.5 USB Port s (CN6, CN63, CN31, CN32) The AIMB-760 provides up to eight ports of USB (Univ ersal Serial Bus) interface w[...]

21 Chapter 2 2.6 VGA Connector (CN7) The AIMB-760 includes a VGA interface that can drive conventional CR T displays. CN7 is a standard 15-pin D-SUB connector comm only used for VGA. Pin assi gnments for CR T connector CN7 are detailed in Appendix B. 2.7 Serial Port s (C OM1:CN9; COM2:CN10) The AIMB-760 offers one serial port and one onboard connec[...]

AIMB-760 User Manual 22 Different devices implement the RS-232 standard in different ways. If you are having problems with a serial device, be su re to check the pin assignments for the connector . 2.8 PS/2 Keyboard a nd Mouse Connector (CN1 1) T wo 6-pin m ini-DIN connectors (CN11) on the motherboard provide connection to a PS/2 keyboard and a PS/[...]

23 Chapter 2 2.9 External Keyboard & Mouse (CN12) In addition to the PS/2 mouse/keyboard connector on the AIMB-760's rear plate, there is also an extra onboard external keyboard and mouse connector . This gives system integr ators greater flexibility in designing their system s. 2.10 CPU Fan Connector (CN14) If fan is used, this connector [...]

AIMB-760 User Manual 24 2.1 1 System F AN Connector (CN15 and CN37) If fan is used, this connector supports cooli ng fans of 500 mA (6W) or less. 2.12 Front Panel Connectors (CN16, 17, 18, 19, 21&29) There are several external switches to monitor and control the AIMB- 760.[...]

25 Chapter 2 2.12.1 Power LED and Keyboard Loc k (CN16) CN16 is a 5-pin connector for the power LED. Refer to Appendix B for detailed information on the pi n assignments. If a PS/2 or A TX power sup- ply is used, the system's power LED status will be as indicated below: 2.12.2 External S peaker (CN17) CN17 is a 4-pin connector for an extern al[...]

AIMB-760 User Manual 26 2.12.5 A TX Sof t Power Switch (CN21) If your computer case is equipped wi th an A TX power supply , you should connect the power on/off button on your computer case to CN21. This connection enables you to turn your com puter on and off. 2.12.6 SM Bus Connector (CN29) This connector is reserved for Advantech's SNMP-1000[...]

27 Chapter 2 2.14 USB and LAN ports (CN31 and CN32) The AIMB-760 provides up to eight US B (Universal Serial Bus) ports, which gives complete Pl ug & Play and hot swapping for up to 127 exter- nal devices.The USB interface complies with USB Specification Rev . 2.0 support transmission rate up to 480 M bps and is fuse-protected. The USB interfac[...]

AIMB-760 User Manual 28 2.15 Line Out, Mic In Connector (CN55) The Line Out is to output the audio signal to external aud io device, like speakers or headphones. The Mic In is for the audio si gnal input via microphones. 2.16 Audio Input from CD-ROM (CD IN; CN56) CD IN is connected the CD-ROM audio output.[...]

29 Chapter 2 2.17 Aux Line-In Connector (AUX IN; CN57) The connector is for audio devi ces with a Li ne-in connector . 2.18 Front Panel Audio C onnector (FP AUDIO; CN59) The FP AUDIO is a front panel audio connector compliant with Intel® Front Panel I/O Connectivity Design Guid e. T o direct th e audio signal output to th e rear audio ports, th e [...]

AIMB-760 User Manual 30 2.19 8-pin Alarm Board Connector (CN62) The 8-pin alarm board co nnector is for Advantech chassis with alarm board, which gives warnings if the po wer supply or fan fails; if the chas- sis overheats; or if th e backplane malfunctions. 2.20 Case Open Connector (CN64) The 2-pin case open connector is fo r chassis with a case o[...]

31 Chapter 2 2.21 Front Panel LAN Indicator Connector T able 2.2: Front Panel LAN Indicator Connector LAN Mode Indicator G-LAN Link ON Green ON G-LAN Active Green Flash G-LAN Link Off Green OFF[...]

AIMB-760 User Manual 32 2.22 Serial A T A Interface (SA0, SA1, SA2, SA3) In addition to the EIDE interface (up to two devices), the AIMB-760 fea- tures a high performance serial A T A interface (up to 150 MB/s) which eases cabling to hard drives with thin and long cables.[...]

33 Chapter 2 2.23 PCI Slot s (PCI 1 ~ PC I 5) The AIMB-760 provides 5 32-bit / 33 MHz PCI slot s. 2.24 Connecting to SNMP -1000 Remote Manager Use the 6 -pin to 8-pin cable t o connect the mot herboard to SN MP-1000. This cable comes wi th the SNMP-100 0. Note: 64-bit PCI or PCI-X exp ansion cards insta lled in the PCI 3 and PCI 4 slots will not fi[...]

AIMB-760 User Manual 34 2.25 Auxiliary 4-pin power connector (A TX1) T o ensure the eno ugh power is supplied to t he motherboard, one auxiliary 4 pin power connecto r is available on the AIMB-760. A TX1 must be used to provide sufficient 12 V power to ensure the stable operatio n of the sys- tem.[...]

35 Chapter 3 CHAPTER 3 A ward BIOS Setup[...]

AIMB-760 User Manual 36 Chapter 3 A ward BIOS Setup 3.1 Introduction A ward’ s BIOS ROM has a built-in setup program that allows users to modify the basic system configu ration. This type of inform ation is stored in battery back ed-up memory (CMOS RAM) so t hat it retains the s etup information when th e power is turned o ff. 3.1.1 CMOS RAM Auto[...]

37 Chapter 3 Figure 3.1: A ward BIOS Setup initial screen 3.3 St andard CMOS Setup 3.3.1 Date The date format is <week>, <month>, <day>, <year>. 3.3.2 Time The time format is <hour> <minute> <seco nd>, based on the 24-hour clock. 3.3.3 IDE channel 0/1 Master/Slave • IDE HDD Auto-Detection : Press “Enter[...]

AIMB-760 User Manual 38 • Landing Zone : Landing zone • Sector : Number of sectors 3.3.4 Drive A / Drive B This category identifies the types of flopp y disk drives installed in the system. The options are: None/360 K, 5.25"/1.2M, 5.25"/720K, 3.5"/ 1.44M, 3.5"/2 .88M, 3.5". 3.3.5 Halt On This category determines wh ethe[...]

39 Chapter 3 3.4 Advanced BIOS Features The “Advanced BIOS Features” scr een appears when choosing the “Advanced BIOS Features” item from th e “Initial Setup Screen” menu. It allows the user to configure the AIMB-760 according to his particular requirements. Below are some majo r items that are provided in the Advanced BIOS Features scr[...]

AIMB-760 User Manual 40 3.4.2 Hard Disk Boot Priority Set hard disk boot device priority . 3.4.3 V irus W arning Enables or disa bles the virus warning. 3.4.4 CPU L1 & L2 Cache Enabling this feature speeds up memory access. The commands are “Enabled” or “Disabled.” 3.4.5 Hyper-Threading T echnology While using a CPU with Hyper- Thr eadi[...]

41 Chapter 3 3.4.13 T ypematic Rate Setting The typematic rate is the rate key strokes repeat as determined by the ke y- board controller . The commands are “Enabled” or “Disabled”. Enabling allows the typematic rate and delay to be selected . 3.4.14 T ypematic Rate (Chars/Sec) The BIOS accepts the following inpu t values (charact ers/secon[...]

AIMB-760 User Manual 42 3.5 Advanced Chip set Features By choosing the “Advanced Chipset Features” option from the “Initial Setup Screen” menu, the screen below will be displayed. Th is sample screen contains the manufacturer ’ s default values for the AIMB-760, as shown in Figure 3-4: 3.5.1 DRAM Timing Select able This item allows you to[...]

43 Chapter 3 3.5.2 CAS Latency Ti me When DRAM Timing Selectable is set to [Manual], this field is adjust- able. This control s the CAS latency , which determ ines the time interval between SDRAM starting a read comm and and receiving it. The options are [3T], [4T], [5 T], and [Auto]. 3.5.3 DRAM RAS# to CAS# Delay When DRAM Timing selectable is set[...]

AIMB-760 User Manual 44 3.5.9 Memory Hole At 15M-16M Enabling this feature reserves 15 MB to 16 MB memory addres s space for ISA expansion cards that specifically require this setting. This makes memory from 15 MB and up unavailable to th e system. Expansion cards can only access memory up to 16 MB. The default setting is “Disabled”. 3.5.10 PCI[...]

45 Chapter 3 3.6 Integrated Peripherals Figure 3.5: Integrated periph erals Figure 3.6: On-Chip IDE Device 3.6.1 IDE HDD Block Mode If your IDE hard drive supports bl ock mode select Enabled for automatic detection of the optimal number of bl ock read/writes per sector the drive can support. 3.6.2 IDE DMA T ransfer Access Use this field to enable o[...]

AIMB-760 User Manual 46 3.6.3 On-Chip IDE Device IDE Primary Master/Slave PIO/UDMA Mode (Auto). The channel has both a master and a slave, making four IDE devices possible. Because two IDE devices may have a different Mode timing (0, 1, 2, 3, 4), it is necessary for these to be independe nt. The default setting “Auto” will allow auto detection [...]

47 Chapter 3 Figure 3.7: Onboard Device 3.6.8 USB Controller Select Enabled if your system contains a Universal Serial Bus (USB) con- troller and you have USB peripherals. The choices are “Enabled” and “Disabled”. 3.6.9 USB 2.0 Controller This entry is to disable/enable th e USB 2.0 controller on ly . The BIOS itself may/may not have high-s[...]

AIMB-760 User Manual 48 . Figure 3.8: Super I/O Devi ce 3.6.14 KBC Input Clock This BIOS feature allows you to adju st the keyboard interface clock for a better response or to fix a keyboard problem. It is recom mended that you select the 16 MHz option for a better keyboard response. But if th e key- board perfor ms erratically or fails to initiali[...]

49 Chapter 3 3.6.20 IR T ransmission Delay This item allows you to enable /disable IR transmission delay . The choices are “Enabled” and “Disabled”. 3.6.21 UR2 Duplex Mode This item allows you to select the IR half/full duplex function. The choices are “Half” and “Full”. 3.6.22 Use IR Pins The choices are “RxD2, TxD2” and “IR-[...]

AIMB-760 User Manual 50 3.7 Power Management Setup The power management setup controls the single board computer's “green” features to save power . The following screen shows the manufac- turer ’ s defaults. Figure 3.9: Power manage ment setup screen (1) 3.7.1 Power Supply T ype AIMB-760 can support both “A TX” and “A T” power su[...]

51 Chapter 3 3.7.3 Power Management This category allows you to select the type (or degree) of power saving and is directly related to the following mo des: • HDD Power Down • Suspend Mode There are three selecti ons for Power Management, and they have fixed mode settings. 3.7.4 V ideo Off Method Use this to select the method to turn off the vi[...]

AIMB-760 User Manual 52 3.7.9 Sof t-Off by PWR-BTTN If you choose “Instant-Off”, then pushing the A TX soft power switch but- ton once will switch the system to “system off” power mode. Y ou can choose “Delay 4 sec”. If you do, then pushing the button for more than 4 seconds will turn off the system, whereas pushing the button momentari[...]

53 Chapter 3 3.8 PnP/PCI Configurations Figure 3.10: PnP/PCI configurations screen 3.8.1 Reset Configuration Dat a The default is Disabl ed. Select Enabled to reset Extended System Config- uration Data (ESCD) if y ou have installed a new add -on card, and system configuration is in such a st ate that the OS cannot boot. 3.8.2 Resources Controlled B[...]

AIMB-760 User Manual 54 3.9 PC Health St atus Figure 3.1 1: PC Health S tatus Screen 3.9.1 Case Open W arning Enable this to detect if the case is open or closed. 3.9.2 CPU W arning T emperature This item will prevent the CPU from overheating. The choices are “Dis- abled”, “60C/140F”, “63C/145F”, “66C/151F”, “70C/158F”, “75C/ [...]

55 Chapter 3 3.9.8 Shut down T emperature The system will shut down au tomati cally when the CPU temperature is over the selected setting. This fu nction can prevent CPU damage caused by overheating. 3.10 Frequency / V olt age Control Figure 3.12: Spread Spe ctrum Co ntrol scree n 3.10.1 CPU Clock Ratio T ype a DEC number to set up the CPU Clock Ra[...]

AIMB-760 User Manual 56 3.1 1 Password Setting Follow these steps to change the password. 1. Choose the “Set Password” option from the “Initial Setup Screen” menu and press <Enter>. The screen displays the following mes- sage: 2. Press <Enter>. 3. If the CMOS is good and this option has been used to change the default password, [...]

57 Chapter 4 CHAPTER 4 Chip set Sof tware Inst allation Utility[...]

AIMB-760 User Manual 58 Chapter 4 Chip set Sof tware Inst all Utility 4.1 Before you begin T o facil itate the installation of the enhanced display dri vers and utility software, read the instructions in th is chapter carefully . The drivers for the AIMB-760 are located on the soft ware installation CD. The auto-run function of the driver CD will g[...]

59 Chapter 4 • Integrates superio r video features. These include filtered sealing of 720 pixel DVD content, and MPEG-2 motio n compensation for software DVD 4.3 Windows XP Driver Setup 1. Insert the driver CD into your system's CD-ROM drive. In a few seconds, the software installation main menu ap pears. Move the mouse cursor over the “Au[...]

AIMB-760 User Manual 60 2. Click “Next” when you see the follow ing message. 3. Click “Y es” when you see the following message.[...]

61 Chapter 4 4. Click “Next” when you see the follow ing message. 5. When the following message appear s, click “Fi nish” to complete the installation an d restart W indows.[...]

AIMB-760 User Manual 62[...]

63 Chapter 5 CHAPTER 5 VGA Setup[...]

AIMB-760 User Manual 64 Chapter 5 VGA Setup 5.1 Introduction The Intel 915GV integrated graphics controller provides an analog dis- play port and DVI interface through SDVO ports. Y ou need to install the VGA driver to enable the function. The Intel 915GV integrated graphics con troller includes the following features. • Intel Graphics Media Acce[...]

65 Chapter 5 5.2 Windows XP Driver Setup Insert the driver CD into your system 's CD-ROM drive. In a few seconds, the software installation m ain menu appears, as shown in the following figure. The following installation pro cedure is for W indows XP . For other oper- ating systems, please do a manual installation. Note: Before installing this[...]

AIMB-760 User Manual 66 1. Click “Next” to continue the in stallation. 2. Y ou will see a welcome win dow . Pl ease click “Y es” to continue the installation. .[...]

67 Chapter 5 3. Click “Finish” to complete the installation and restart the comp uter now or later .[...]

AIMB-760 User Manual 68[...]

69 Chapter 6 CHAPTER 6 Onboard Security Setup[...]

AIMB-760 User Manual 70 Chapter 6 Onboard Security Setup 6.1 Introduction The AIMB-760's hardware monit or is based on the W inbond W83627HF chip. Onboard security (OBS) functions mon itor key hardware to help you maintain system stabili ty and durability . The AIMB-760 can monitor five sets of positive system voltages, two set s of system neg[...]

71 Chapter 6 2. Click “Next” when you see the follow ing message. 3. Click “Next” when you see the follow ing message.[...]

AIMB-760 User Manual 72 4. Click “Next” when you see the follow ing message. 5. Click “Next” to continue.[...]

73 Chapter 6 6. Click “Finish” when you see the following message. 6.3 Using the OBS Hardwa re Doctor Utility After completing the setup, all th e OBS functions are permanently enabled. When a monitored reading exceeds safe limits, a warning mes- sage will be displayed and an error beep will sound to attract your atten- tion. OBS Hardware Docto[...]

AIMB-760 User Manual 74[...]

75 Chapter 7 CHAPTER 7 LAN Configuration[...]

AIMB-760 User Manual 76 Chapter 7 LAN Configuration 7.1 Introduction The AIMB-760 features a single/dual Gigabit Ethe rnet network interface. W ith the Broadcom BCM5721 GbE controller built in, AIMB-7 60 uses the PCI Express host interface (PCI-E X1) for LAN connectivity with a maximum throughpu t of 2 Gbps for heavy-duty industrial netw ork appli-[...]

77 Chapter 7 7.4 Win XP Driver Setup (Broadcom BCM5721) 1. Insert the driver CD into your system's CD-ROM drive. In a few seconds, the software installation main menu appears, as shown in the following figure. Under the “L AN Drivers” heading , click on the “Manual” to open file mana ger , then click “SETUP .EXE” to run the install[...]

AIMB-760 User Manual 78 3. The license agreement appears. Clic k “Next” to continue the instal- lation. 4. Click “Install” to continu e.[...]

79 Chapter 7 5. Click “Finish” to comple te the installation.[...]

AIMB-760 User Manual 80[...]

81 Appendix A Appendix A Programming the W atchdog T imer[...]

AIMB-760 User Manual 82 Appendix A W atchdog T imer A.1 Programming the W atchdog Timer The AIMB-760's watchdo g timer can be used to moni tor system software operation and take corrective action if the software fai ls to function within the programmed p eriod. This s ection describes the operatio n of the watchdog timer and how to program it [...]

83 Appendix A Unlock W83627HF Select register of watchdog timer Enable the function of the watchdog timer Use the function of Lock W83627HF the watchdog timer[...]

AIMB-760 User Manual 84 T a ble A.1: W atchdog tim er registers Address of register (2E) Attribute Read/Write V alue (2F) & description 87 (hex) ----- Write this address to I/O address port 2E (hex) twice to unlock the W83627HF 07 (hex) write Write 08 (hex) to select register of watchdog timer . 30 (hex) write Write 01 (hex) to enable the func-[...]

85 Appendix A A.1.4 Example Program 1. Enable watchdog timer and set 10 sec. as timeout interval ;-------- --------- ----------- ---------- --------- ---------- -- Mov dx,2eh ; Unlock W83627HF Mov al,87h Out dx,al Out dx,al ;-------- --------- ----------- ---------- --------- ---------- -- Mov al,07h ; Select registers of watchdog timer Out dx,al I[...]

AIMB-760 User Manual 86 Inc dx Mov al, 10 Out dx,al ;-------- --------- ----------- ---------- --------- ---------- -- Dec dx ; lock W83627HF Mov al,0aah Out dx,al 2. Enable watchdog tim er and set 5 minutes as timeout interval ;-------- --------- ----------- ---------- --------- ---------- -- Mov dx,2eh ; unlock W83627HF Mov al,87h Out dx,al Out d[...]

87 Appendix A In al,dx Or al,08h Out dx,al ;-------- --------- ----------- ---------- --------- ---------- -- Dec dx ; Set timeout interval as 5 minutes and start counting Mov al,0f6h Out dx,al Inc dx Mov al, 5 Out dx,al ;-------- --------- ----------- ---------- --------- ---------- -- Dec dx ; lock W83627HF Mov al,0aah Out dx,al 3. Enable watchdo[...]

AIMB-760 User Manual 88 Mov al,01h Out dx,al ;-------- --------- ----------- ---------- --------- ---------- -- Dec dx ; Enable watchdog timer to be reset by mous e Mov al,0f7h Out dx,al Inc dx In al,dx Or al,80h Out dx,al ;-------- --------- ----------- ---------- --------- ---------- -- Dec dx ; lock W83627HF Mov al,0aah Out dx,al 4. Enable watch[...]

89 Appendix A Mov al,01h Out dx,al ;-------- --------- ----------- ---------- --------- ---------- -- Dec dx ; Enable watchdog timer to be strobed reset by keyboard Mov al,0f7h Out dx,al Inc dx In al,dx Or al,40h Out dx,al ;-------- --------- ----------- ---------- --------- ---------- -- Dec dx ; lock W83627HF Mov al,0aah Out dx,al 5. Generate a t[...]

AIMB-760 User Manual 90 Mov al,01h Out dx,al ;-------- --------- ----------- ---------- --------- ---------- -- Dec dx ; Generate a time-out signal Mov al,0f7h Out dx,al ;W rite 1 to bit 5 of F7 register Inc dx In al,dx Or al,20h Out dx,al ;-------- --------- ----------- ---------- --------- ---------- -- Dec dx ; lock W83627HF Mov al,0aah Out dx,a[...]

91 Appendix B Appendix B I/O Pin Assignment s[...]

AIMB-760 User Manual 92 Appendix B Pin Assignment s B.1 IDE Hard Drive Connector (CN1) T able B.1: IDE hard drive connector (CN1) Pin Signal Pin Signal 1 IDE RESET* 2 GND 3D A T A 7 4 D A T A 8 5D A T A 6 6 D A T A 9 7D A T A 5 8 D A T A 1 0 9 DA T A 4 10 DA T A 1 1 11 D ATA 3 1 2 D ATA 1 2 13 DA T A 2 14 DA T A 13 15 DA T A 1 16 DA T A 14 17 DA T [...]

93 Appendix B B.2 Floppy Drive Connector (CN3) T a ble B.2: Floppy drive connector (CN3) Pin Signal Pin Signal 1 GND 2 FDHDIN* 3G N D 4 N / C 5 N/C 6 FDEDIN* 7 GND 8 INDEX* 9 GND 10 MOTOR 0* 1 1 GND 12 DRIVE SELECT 1* 13 GND 14 DRIVE SELECT 0* 15 GND 16 MOTOR 1* 17 GND 18 DIRECTION* 19 GND 20 STEP* 21 GND 22 WRITE DA T A* 23 GND 24 WRITE GA TE* 25 [...]

AIMB-760 User Manual 94 B.3 Parallel Port (CN4) T able B.3: Parallel Por t (CN4) Pin Signal Pin Signal 1 STROBE* 14 AUTOFD* 2D 0 1 5 E R R 3D 1 1 6 I N I T * 4D 2 1 7 S L C T I N I * 5D 3 1 8 G N D 6D 4 1 9 G N D 7D 5 2 0 G N D 8D 6 2 1 G N D 9D 7 2 2 G N D 10 ACK* 23 GND 1 1 BUSY 24 GND 12 PE 25 GND 13 SLCT 26 N/C * low activity[...]

95 Appendix B B.4 USB Header (CN6/CN63) T a ble B.4: USB Header (CN6/CN63) Pin Signal Pin Signal 1 USB0_VCC5 6 USB1_D+ 2 USB1_VCC5 7 GND 3 USB0_D- 8 GND 4 USB1_D- 9 Key 5 USB0_D+ 10 GND[...]

AIMB-760 User Manual 96 B.5 VGA Connector (CN7) T able B.5: VGA Connector (CN7) Pin Signal Pin Signal 1R E D 9 V C C 2G R E E N 1 0 G N D 3B L U E 1 1 N / C 4N / C 1 2 S D T 5 GND 13 H-SYNC 6 GND 14 V -SYNC 7G N D 1 5 S C K 5 15 1 11 10 6[...]

97 Appendix B B.6 RS-232 Interface (CN9/10) T able B.6: RS-232 Interface (C N9/10) Pin Signal 1 DCD 2R X D 3T X D 4D T R 5G N D 6D S R 7R T S 8C T S 9R I CN10 CN9[...]

AIMB-760 User Manual 98 B.7 PS/2 Keyboard and Mouse Connector (CN1 1) T a ble B.7: Keyboard and Mouse Connector (CN1 1) Pin Signal 1 KB DA T A 2N / C 3G N D 4 KB VCC 5 KB CLK 6 N / C[...]

99 Appendix B B.8 External Keyboard Connector (CN12) B.9 Infrared (IR) connector (CN13) T able B.8: External Keyboard Connector (CN12) Pin Signal 1C L K 2D A T A 3N C 4G N D 5 VCC T able B.9: Infrared Connector (CN 13) Pin Signal 1V C C 2N / C 3 IRRX 4G N D 5I R T X[...]

AIMB-760 User Manual 100 B.10 CPU/System Fan Po wer Connector (CN14/15/37) B.1 1 Power LED and Keyboard Lock (CN16) T able B.10: Fan Power Connector (CN14/15/37) Pin Signal 1G N D 2 +12V 3D E T E C T T a ble B.1 1: Power LED and Keyboard Lock (CN16) Pin Function 1 LED power (+5 V) 2N C 3G N D 4N C 5G N D[...]

101 Appendix B B.12 External Speak er Connector (CN17) B.13 Reset C onnector (CN18) T a ble B.12: External Speaker Connector (CN17) Pin Function 1 Buzzer 2N C 3 Buzzer 4 S peaker out T able B.13: Reset Connector (CN18) Pin Signal 1 RESET 2G N D 1[...]

AIMB-760 User Manual 102 B.14 HDD LED Connector (CN19) B.15 A TX Soft Power Switch (CN21) B.16 H/W Monitor Alarm (CN22) T a ble B.14: HDD LED Connector (CN19) Pin Signal 1 VCC (LED+) 2 IDE LED (LED-) T able B.15: A TX Soft Power Switch (CN21) Pin Signal 1 5VSB 2P W R - B T N 1 1[...]

103 Appendix B B.17 SM Bus Connector (CN29) T able B.16: H/W Moni tor Alarm (CN22) Pin Signal 1 Enable OBS alarm 2 Disable OBS alarm T able B.17: SM Bus Connector (CN 29) Pin Signal 1S M B _ D A T A 2S M B _ C L K 1 1[...]

AIMB-760 User Manual 104 B.18 USB/LAN por t s (CN31 and CN32) B.19 Line Out, Mi c IN Connector (CN55) T able B.18: USB Port Pin Signal Pin Signal 1V C C 3 D a t a 0 + 2 Data0- 4 GND T able B.19: Ethernet 10/100Bas e-T RJ-45 port Pin Signal Pin Signal 1X M T + 5 N / C 2X M T - 6 R C V - 3 RCV+ 7 N/C 4N / C 8 N / C Line Out MIC in[...]

105 Appendix B B.20 Audio Input from CD-ROM (CD IN; CN56) B.21 Aux Line-In Connector (CN57) T able B.20: Audio Input from CD-ROM Pin Signal Pin S ignal 1 CD_L 3 GND 2 GND 4 CD_R T able B.21: Aux Line-In Connector (CN57) Pin Signal Pin Signal 1 AUX_L 3 GND 2G N D 4 A U X _ R[...]

AIMB-760 User Manual 106 B.22 Front Panel Audio Connector (FP AUDIO; CN5 9 B.23 8-pin Alarm Bo ard Connector (CN62) T able B.22: Audio Connector (FP AUDIO; CN59) Pin Signal Pin Signal 1 MIC 6 LOU T_RR 2G N D 7 N C 3 MIC_BIAS 8 NC 4V C C 9 L O U T _ L 5L O U T _ R 1 0L O U T _ L L T ab le B.23: 8-pin Alarm Board Connector (CN62) Pin Signal Pin Signa[...]

107 Appendix B B.24 Case Open Connector (CN64 B.25 Front Panel LA N LED Connector (CN65) T a ble B.24: Case Open Connector (CN64) Pin Signal 1 CASEOP 2G N D T ab le B.25: LAN LED Connector (CN65) Pin Signal Pin Signal 1 LAN1_LINK 2 LAN2_LINK 3 LAN1_ACT 4 LAN2_ACT 5 LAN1_LINK100 0 6 LAN2_LINK100 0 7 LAN1_LINK100 8 LAN2_LINK1 00 9 3VDUAL 10 N/C 1 7 3[...]

AIMB-760 User Manual 108 B.26 System I/O Port s T able B.26: System I/O ports Addr . range (Hex) Device 000-01F DMA controller 020-021 Interrupt controller 1, master 022-023 Chipset address 040-05F 8254 timer 060-06F 8042 (keyboard controller) 070-07F Real-time clock, non-maskable interrupt (NMI) mask 080-09F DMA page register 0A0-0BF Interrupt con[...]

109 Appendix B B.27 DMA Channel Assignment s T a ble B.27: DMA channel assignments Channel Functi on 0 Available 1 Available 2 Floppy disk (8-bit transfer) 3 Available 4 Cascade for DMA controller 1 5 Available 6 Available 7 Available[...]

AIMB-760 User Manual 110 B.28 Interrupt Assignment s B.29 1st MB Memory Map T able B.28: Interrupt assign ments Priority Interrupt# Interrupt source 1 NMI Parity error detected 2 IRQ0 Interval timer 3 IRQ1 Keyboard - IRQ2 Interrupt from controller 2 (cascade) 4 IRQ8 Real-time clock 5 IRQ9 Cascaded to INT 0A (IRQ 2) 6 IRQ10 Available 7 IRQ1 1 Availa[...]