AGFA ATCA-C110/1G Bedienungsanleitung

REVIE W COPY A TCA-C110/1G AMC Carrier Blade Installation and Use 225254 420 000 AA September 2005 Edition[...]

REVIE W COPY © Cop yright 2005 Motorola, Inc. All rights reser ved. Printe d in the United States of Ame rica. T rademarks Motorola and the styliz ed M logo are tr ademarks registered in the U . S. P atent and T rademark Office . PICMG, Adv ancedTCA, and the Adv ancedTCA logo are regist ered tradema rks of PCI Industrial Computer Manuf acturers Gr[...]

REVIE W COPY Safety Summary The follo w ing general saf ety precautions must be obser ved during all phases of operation, ser vice, and repair of this equipment. F ailure to comply with these precautions or with specific warnings elsewhere in this manual could result in personal injur y or damage to the equipment. The safety precautions listed belo[...]

REVIE W COPY Flammability All Motorola PWBs (pr inted wiring boards) are manuf actured with a fla mmability rating of 94V -0 by UL- recognized manufacturers. EMI Caution ! Caution Caution This equipme nt generates, uses and can radiate electr omagnetic ener gy . It may cause or be susceptib le to electroma gnetic interf erence (EMI) if not installe[...]

REVIE W COPY Motorola product s with the CE marking comply with the EMC Directiv e (89/336/EEC). Complia nce with this directive implies conf or mity to the follo wing European Norms: EN55022 “Limits and Metho ds of Measurement of Radio Int erf erence Chara cteristics of Inf or mation T echnolog y Equipment”; this product tested to Equipmen t C[...]

REVIE W COPY Notice While reasonab le efforts hav e been made to assure the accuracy of this document, Moto rola, Inc. assumes no liability resulting from any omission s in this document, or from the use of the inf or mation obtained therein. Motorola rese r ves the right to re vise this d ocument and to make changes from tim e to time in th e cont[...]

REVIE W COPY ATCA-C110/1G Installation and Use Manual vii About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x vii Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[...]

REVIE W COPY ATCA-C110/1G Installation and Use Manu al Contents viii Control Elem ents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Injector/Eject or Lever and Ho t Swap Switch Me chanism . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Verify Slot Us age . . . . . . [...]

REVIE W COPY ATCA-C110/1G Installation and Use Manual ix Contents Boot Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 System Man agement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [...]

REVIE W COPY ATCA-C110/1G Installation and Use Manu al Contents x Zone 3 Conn ectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 6 Memory Map and Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 Memory Ma [...]

REVIE W COPY ATCA-C110/1G Installation and Use Manual xi Contents Manufactu rers’ Documen ts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 Related Spe cifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[...]

REVIE W COPY[...]

REVIE W COPY Figure 1-1. Board Lay o ut Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Figure 1-2. Ba y Location s on A TCA-C110/1G . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Figure 1-3. F abr ic Interface Module Insta llation . . . . . . .[...]

REVIE W COPY[...]

REVIE W COPY ATCA-C110/1G Installation and Use Manual xv T able 1. Order ing Infor mation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xviii T able 2. Accessor ies Orde ring In f o r mation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xviii T able [...]

REVIE W COPY ATCA-C110/1G Installation and Use Manu al List of Table s xvi T able 6-8. I2C to G PIO’ s Device Mappings - A TMega64 -AMC Private I2C Bus . . . . . . . . . . . . . . . . 80 T able 6-9. Geo graphical addressing of AMC Bays on A TCA-C110/1G . . . . . . . . . . . . . . . . . . . . . . 82 T able 6-10. Et her net Phy Address Map . . . . [...]

ATCA-C110/1G Installation and Use Manual xvii REVIE W COPY About This Manual This manua l provides bo th general and f unctional descriptions of the product along with installation and re mov al instr uctions, fir mware details, conn ector pin assignments , memor y maps, tr ouble shooting inf or mation, specifications , thermal validation and rela [...]

ATCA-C110/1G Installation and Use Manu al About This Manua l xviii REVIE W COPY Or der Numbers The tab le below is an e xcer pt from the b lade’ s ordering information. Ask y our local Motorola representati ve f or the current ordering inf or mation. The tab le below is an e xcer pt from the b lade’ s accessories ordering inf or mation. Ask y o[...]

About This Manual ATCA-C110/1G Installation and Use Manual xix REVIE W COPY Appendix C, Thermal V alidation , pro vides inf orm ation about t hermally significant components and an o v er view of ho w to measure v ar ious junction and case temper atures. Appendix D , Related Documentation , lis ts other Mo torola Compu ter Group do cuments, industr[...]

ATCA-C110/1G Installation and Use Manu al About This Manua l xx REVIE W COPY Miscellaneous notations The term AMC Carrier refer s to the A TCA-C 110/1G board/b lade, and is used interchang eably . The phrases Service Processor and MPC8540 are used interchangeab ly . The term xY in reference to a ser ial link refers to a link w ith a width of Y L an[...]

About This Manual ATCA-C110/1G Installation and Use Manual xxi REVIE W COPY Use ESD Wrist Strap Befor e you install or remo ve a board Motor ola str ongly recommends that y ou use an antistatic wrist strap and a conductive f oam pad. ! Wa r n i n g Identifies any ri sk of per sonal injury or loss o f life and should e xplicitl y state the nat ure o[...]

ATCA-C110/1G Installation and Use Manu al About This Manua l xxii REVIE W COPY MA C Mediu m Access Controller (for Ethernet) MII Media Independent Interface (f or Eth ernet) MIIM Media Independent Interface Management NMI Non-maskable interr upts NPTH Non-Plated Through -hole PCA Printed Circu it Assemb ly PCB Printed Circuit Board PCI P er ipheral[...]

1 ATCA-C110/1G Installation and Use Manual 1 REVIE W COPY 1 A TCA- C110/1G Baseboard Preparation and Installation Intr oduction This chapter outlines star tup and s af ety inst r uctions, hardware acce ssories details, s w itch settings , hardwar e preparation, installation and remo val instructions. Pr oduct Description The A TCA- C110/1G is an Ad[...]

ATCA-C110/1G Installation and Use Manu al Chapter 1 ATCA-C110 /1G Baseboard Pre paration and I nstallation 2 REVIE W COPY ■ Onboard De vices such as: – PCI to PCI-Express Bridge – GigE PHYs – BCM56502 GigE Switch (de vice on FIM) – PEX8532 PCI-Express Sw itch (dev ice on FIM) – SA T A Multiplex er (device on FIM) The details of maj or o[...]

Chapter 1 ATCA-C110/1G Baseboard Preparat ion and Installation ATCA-C110/1G Installation and Use Manual 3 REVIE W COPY Baseboar d Lay out The figure belo w shows the placement of the components on the A TCA- C110/1G board. Equipment Required T o install the A TCA- C110/1G board y ou need the f ollowing equipment: ■ PICMG 3.0 Compliant Ad vanced T[...]

ATCA-C110/1G Installation and Use Manu al Chapter 1 ATCA-C110 /1G Baseboard Pre paration and I nstallation 4 REVIE W COPY The A TCA- C110/1G has t wo f ace plates: top and b ottom, which are moun ted on the top strut and bottom strut, resp ectiv ely . No front pan el I/O is present on th e A TCA- C110/1G board. See F ace plat e and LEDs on page 51 [...]

Chapter 1 ATCA-C110/1G Baseboard Preparat ion and Installation ATCA-C110/1G Installation and Use Manual 5 REVIE W COPY Getting Star ted This section pro vides an ov er view of the step s necessar y to install the A TCA- C110/1G and a brief section on unpac king and ESD precautions . Overview of Star tup Pr ocedures Ta b l e 1 - 1 lis ts the things [...]

ATCA-C110/1G Installation and Use Manu al Chapter 1 ATCA-C110 /1G Baseboard Pre paration and I nstallation 6 REVIE W COPY Caution Caution A void touc hing areas of integrated circuitry; st atic dischar ge can damage circuits. Use ESD Wrist Strap ESD Motor ola str ongly reco mmends that y ou use an antistatic wrist strap and a conductive foa m pad w[...]

Chapter 1 ATCA-C110/1G Baseboard Preparat ion and Installation ATCA-C110/1G Installation and Use Manual 7 REVIE W COPY Har dware Upgrades and Accessories Hardware upgrades an d accessories allow an easy and cost -efficient wa y to adapt the system board to y our application needs. The f ollowing hardware up grades and accessories are a vailab le: ?[...]

ATCA-C110/1G Installation and Use Manu al Chapter 1 ATCA-C110 /1G Baseboard Pre paration and I nstallation 8 REVIE W COPY Step 3: After rem oving the carrier board from its card slot, place it on a clean and adequately pr otected working surface (preferably an ESD mat) with the bottom side of the board facing up. Step 4: Remove the screws from the [...]

Chapter 1 ATCA-C110/1G Baseboard Preparat ion and Installation ATCA-C110/1G Installation and Use Manual 9 REVIE W COPY SO-DIMM Installation in a Non-P owered System Note ■ The SO-DIMM onboard the A TCA-C110/1 G can be installed only when th e module is remov ed from the carrier board. ■ It is recommended to use the SODIMM that is f actor y-ship[...]

ATCA-C110/1G Installation and Use Manu al Chapter 1 ATCA-C110 /1G Baseboard Pre paration and I nstallation 10 REVIE W COPY Step 3: Firmly insert th e SO-DIMM into the socket at a 45° angle in the direction as indicat ed in Figure 1-6 . Push the SO-DIM M down until th e retaining clip o f the socket loc ks the SO-DIM M into position. Step 4: The fu[...]

Chapter 1 ATCA-C110/1G Baseboard Preparat ion and Installation ATCA-C110/1G Installation and Use Manual 11 REVIE W COPY Removing SO-DIMM T o remov e the SO-DIMM from the SO-DIMM sock et on the A TCA- C110/1G f ollow these steps: Step 1: Pull the two retaining clips of the SO-DIMM socket in an outward direction, pa rallel to the surface of the boar [...]

ATCA-C110/1G Installation and Use Manu al Chapter 1 ATCA-C110 /1G Baseboard Pre paration and I nstallation 12 REVIE W COPY Installing an AMC Module in a P owered System T o install an AMC Module on a Adv ancedTCA host board, ref er to the Figure 1-10 on page 13 , read all cautions and w ar nings and perf or m the f ollowing steps . This figure is f[...]

Chapter 1 ATCA-C110/1G Baseboard Preparat ion and Installation ATCA-C110/1G Installation and Use Manual 13 REVIE W COPY Step 2: Identify the AMC bay to be used for ins ta llation. Please note th e following possibilities: – If the required AMC bay is occupied b y the AMC filler panel, you will need to remo ve the filler panel bef ore proceeding w[...]

ATCA-C110/1G Installation and Use Manu al Chapter 1 ATCA-C110 /1G Baseboard Pre paration and I nstallation 14 REVIE W COPY Remo ving an AMC Module from a P o wered System T o remov e an AMC Module from the A TCA- C110/1G, read all cautio ns and warnings and perf or m the f ollowing steps . Wa r n i n g Warni ng Dangerous v oltages, capable of caus [...]

Chapter 1 ATCA-C110/1G Baseboard Preparat ion and Installation ATCA-C110/1G Installation and Use Manual 15 REVIE W COPY Rear T ransition Modules At the time of writing this manual the A CC/AR TM-C110 Rear T ransition Module w as av ailable f or the blade. F or fur ther inform ation, refer to the ACC/AR TM-C110 Installation and Use manual . The RTM [...]

ATCA-C110/1G Installation and Use Manu al Chapter 1 ATCA-C110 /1G Baseboard Pre paration and I nstallation 16 REVIE W COPY Switch Settings The b lade pro vides the configur ation s witch SW1. The s witch pro vides AMC ba y selection in the JT AG cha in. The board is deliv ered with the white s witch set to the def ault OFF position. Ref er to T abl[...]

Chapter 1 ATCA-C110/1G Baseboard Preparat ion and Installation ATCA-C110/1G Installation and Use Manual 17 REVIE W COPY Observe ESD Precautions Use ESD Wrist Strap ESD Motor ola str ongly reco mmends that y ou use an antistatic wrist strap and a conductive foa m pad when installing or up grading a syste m. Electr onic components , such as disk driv[...]

ATCA-C110/1G Installation and Use Manu al Chapter 1 ATCA-C110 /1G Baseboard Pre paration and I nstallation 18 REVIE W COPY Understand Hot Swap ! Caution Caution Boar d/Component Damage Inserting or removing non-hot swap car ds or transiti on modules wi th pow er applied may res ult in damage to module components. Make sure that y our blade manufact[...]

Chapter 1 ATCA-C110/1G Baseboard Preparat ion and Installation ATCA-C110/1G Installation and Use Manual 19 REVIE W COPY Note The hot-swap s witch contacts should be in the OFF position (high- resistance) whe n the board handle s are fully inserted. Ve r i f y S l o t U s a g e ! Caution ESD Prevent possible dama ge to module components b y verifyin[...]

ATCA-C110/1G Installation and Use Manu al Chapter 1 ATCA-C110 /1G Baseboard Pre paration and I nstallation 20 REVIE W COPY Note The A TCA- C110/1G is designed to ope rate as an Adv ancedTCA node board. Ref er to V er ify Slot Usage on p age 19 f o r more details. The inst allation proc edure assumes that the board is be ing hot-inser ted into a liv[...]

Chapter 1 ATCA-C110/1G Baseboard Preparat ion and Installation ATCA-C110/1G Installation and Use Manual 21 REVIE W COPY Note If a Rear T ransition Module (R TM) is already installed in the same slot, be careful not to bend an y pins of the R TM connectors. Step 4: Wait until the blue LED is illuminated. The blue LED indicates that the blade announc[...]

ATCA-C110/1G Installation and Use Manu al Chapter 1 ATCA-C110 /1G Baseboard Pre paration and I nstallation 22 REVIE W COPY Step 1: Remove face pl ate cables and cables from th e AMC, if applicable. Step 2: Loosen the board's capt ive screws. Step 3: Gently pull the top and bo ttom ejector han dles outward from its locked position (Sta ge 2 of [...]

Chapter 1 ATCA-C110/1G Baseboard Preparat ion and Installation ATCA-C110/1G Installation and Use Manual 23 REVIE W COPY Y ou may access the stand ard serial console por t via the AR TM-C110. This ser ial por t serves as the U-Boot and oper ating system (OS) console por t. Ref er to Chapter 3, U- Boot Firmware Overview , f or inf or mation on config[...]

REVIE W COPY[...]

2 ATCA-C110/1G Installation and Use Manual 25 REVIE W COPY 2 Operating Instructions This chapter contains the follo wing information: ■ System Initialization ■ Hot Swap Suppor t on page 26 ■ Booting wit h Fir mware on page 26 System Initialization After you verify that all nec essar y hard ware preparation is comp lete and all co nnections ar[...]

ATCA-C110/1G Installation and Use Manu al Chapter 2 Op erating Instruct ions 26 REVIE W COPY ■ Bef o re the system is po wered up ensure th at chassis pow er supply v oltage settings matches th e voltage present in cou ntr y of use (if the power supply in your syst em is not auto-sensin g). ■ The initial U-Boot boot- up prompt ( A TCA-C110> [...]

Chapter 2 Op erating Instruct ions ATCA-C110/1G Installation and Use Manual 27 REVIE W COPY Deb ug Suppor t The deb ug mechanisms supported on A TCA- C 110/1G include: ■ Debug connectors f or IPMC A serial interface f or debug will be provid ed f or each A TMega controller . The debug connectors are located on the AR TM-C110 serial por ts COM 1 t[...]

REVIE W COPY[...]

3 ATCA-C110/1G Installation and Use Manual 29 REVIE W COPY 3 U-Boot Fir mw are Ov er vie w U-Boot is a softw are package ba sed on an open-source boo t loader f or embedded systems utilizing P owerPC , MIPS, or ARM Processors. U-Boot can be inst alled in a boot R OM and used as a boot loader to do wnload and activat e application code. F or more de[...]

ATCA-C110/1G Installation and Use Manu al Chapter 3 U-Bo ot Firmware Over view 30 REVIE W COPY # default: off # description: The tftp server serves files using the trivial file transfer # protocol. The tftp protocol is often used to boot diskless # workstations, download configuration files to network-aware printers, # and to start the installation[...]

Chapter 3 U-Boot Firmwar e Overview ATCA-C110/1G Installation and Use Manual 31 REVIE W COPY Using this configuration, the DHCP ser v er will reply to a request from the target with the Ethernet address 00:30:BF :01:02:D0 , pro vided the f ollowing conditions are sa tisfied: ■ The target is locate d in the subnet 1 0.0. 0.0 which uses the netmask[...]

ATCA-C110/1G Installation and Use Manu al Chapter 3 U-Bo ot Firmware Over view 32 REVIE W COPY Initial Steps In the def ault configuration , U-Boot operates in an int eractiv e mode providing a simple command line-oriented user interf ace using the serial console on por t In this CLI mode , U-Boot shows a prompt ( A TCA-C110 >) when it is read y[...]

Chapter 3 U-Boot Firmwar e Overview ATCA-C110/1G Installation and Use Manual 33 REVIE W COPY sleep - delay execution for some time tftpboot- boot image via network using TFTP protocol and env variables ipaddr and serverip version - print monitor version ? - alias for 'help' => T o obtain additional inf or mation about most commands , u[...]

REVIE W COPY[...]

4 ATCA-C110/1G Installation and Use Manual 35 REVIE W COPY 4 Functional Descr iption This chapter describes the functional co ncepts of the A TCA- C110/1G as well as the main ph ysical and electr ical structure of the board. A TCA- C110/1G Overview The f ollowing tabl e lists the f eatures of the A TCA-C 110/1G. T able 4-1. A TCA- C110/1G Over view[...]

ATCA-C110/1G Installation and Use Manu al Chapter 4 Function al Description 36 REVIE W COPY A TCA Compliant features The A TCA- C110/1G complies with the f ollowing f eatures as per the PICMG 3.0 Specificat ion . ■ A TCA Base Interface The Base Interf ace of the A TCA- C110/1G is a Gigabit Ethernet interf ace in a dual star topology on the backpl[...]

Chapter 4 Functional Description ATCA-C110/1G Installation and Use Manual 37 REVIE W COPY Bloc k Diagram – A TCA- C110/1G The A TCA- C110/1G server b lade is divided into se ver al functional b locks, see Figure 4-1 . Each of these function al bloc ks are described in the foll owing section s: ■ Processor and Processor int erf aces on page 38 ?[...]

ATCA-C110/1G Installation and Use Manu al Chapter 4 Function al Description 38 REVIE W COPY Pr ocessor and Processor interfaces CPU A TCA-C 110/1G has MPC854 0 as a Ser vice Processor working with the f ollowing f eatures: ■ e500 high p erf ormance P owerPC core ■ Core opera ting frequency upto 833 Mhz ■ 32 KB L1 data and 32 KB L1 inst ructio[...]

Chapter 4 Functional Description ATCA-C110/1G Installation and Use Manual 39 REVIE W COPY ■ Deliv ering interr upts to the CPU for servicing All the interrupts gener ated on the A TCA-C110 are wired to the interrupt controller of th e MPC8540 Pro cessor . Re f e r to the Int errupt Ma pping on page 72 f or the Interrupt Architec ture. I 2 C Inter[...]

ATCA-C110/1G Installation and Use Manu al Chapter 4 Function al Description 40 REVIE W COPY PCI/PCI-X Interface The MPC8540 pro vides PCI/PCI-X interf ace that complies with the PCI Local Bus Specification, Re v . 2.2 and the PCI-X Addendum to the PCI Local Bus Specification, Rev . 1.0a . The PCI interf ace is 64-bit wide and runs at 66 MHz and is [...]

Chapter 4 Functional Description ATCA-C110/1G Installation and Use Manual 41 REVIE W COPY System Management The A TCA-C110 carries an Intelligent Platf orm Management Controller (IPMC) entity . The IPMC is a chassis management entity on individ ual cards that monitor v oltages, temperat ure, and chassis characteristics. The IPMC commun icates with [...]

ATCA-C110/1G Installation and Use Manu al Chapter 4 Function al Description 42 REVIE W COPY ■ T elecom Clock Interf ace Control ■ Digital IO The IPMI module co nsists of three micro- controllers fro m Atmel. The interf ace of each of the controllers is illustrated below in Figure 4-3 on page 42 . A brief description of the interf aces and the f[...]

Chapter 4 Functional Description ATCA-C110/1G Installation and Use Manual 43 REVIE W COPY Private I 2 C Bus There are tw o private I 2 C busses implemented on the IPMI Module of A TCA- C110/1G. The busses are Master-only I 2 C b usses implemented on the Sla ve micro-controllers . The private I 2 C Bus from the A TMega8 micro-controller has the f ol[...]

ATCA-C110/1G Installation and Use Manu al Chapter 4 Function al Description 44 REVIE W COPY Digital IO The IPMI interf ace of the A TCA- C110/1G helps in the configur ation and oper ations of the board through its GPIO pins. Ref er to Digital IO on pa ge 73 f or more details about t he GPIO pin signals. F abric Interface Module The FIM is used f or[...]

Chapter 4 Functional Description ATCA-C110/1G Installation and Use Manual 45 REVIE W COPY PCI-Express Switch The 16-lane PCI-Expre ss s witch is used as the PCI-Express s witching element on the F abric Interf ace Module of A TCA-C110. The multipurpose PCI-Express swit ch can be used as a f an- out, aggre ssion, peer-to-peer s witch as well as in b[...]

ATCA-C110/1G Installation and Use Manu al Chapter 4 Function al Description 46 REVIE W COPY PCI-Express to PCI Bridge The PCI-to-PCI- Express Bridge acts as the in terf ace between the FIM (through its PCI -Express interf ace) and the Processor of the A TCA-C110. The PCI-Express to PCI Bridge suppor ts full f orward and re verse tra nsparent bridgi[...]

Chapter 4 Functional Description ATCA-C110/1G Installation and Use Manual 47 REVIE W COPY I/O Subsystems Onboard De vices The f ollowing onboard de vices are present on A TCA-C110/1G ■ User Flash ■ AMC Ba ys ■ Progr ammable Logic Device s – CPLD User Flash The A TCA- C110/1G suppor ts upto 128 MB User Flash. The Use r Flash is located on th[...]

ATCA-C110/1G Installation and Use Manu al Chapter 4 Function al Description 48 REVIE W COPY Power-on Sequence The pow er-on sequence is contr olled by the CPLD onb oard the A TCA- C110/1G. The Enable signals from the CPLD enab les the corresponding regula tor and the P ower Good signals from the regulator indicates the st abilization of the co rres[...]

Chapter 4 Functional Description ATCA-C110/1G Installation and Use Manual 49 REVIE W COPY Serial A T A interface The Ser ial A T A (SA T A) interface is a high-s peed ser ialized storage inter f ac e. The 2x SA T A interf ace from the AMC Connectors are route d through the AMC int erconnect to the A TCA-C1 10/1G’ s SA T A Multiplex er on the F ab[...]

ATCA-C110/1G Installation and Use Manu al Chapter 4 Function al Description 50 REVIE W COPY I 2 C Bus There are tw o I 2 C interf aces on the A TCA-C110/1G . ■ The Private I 2 C b uses from the IPMI Controllers ■ The I 2 C interf ace from the MPC8540 The private I 2 C Address Map f or MPC8540 is shown in T able 6-4 on pa ge 74 . R TC interface [...]

5 ATCA-C110/1G Installation and Use Manual 51 REVIE W COPY 5 Controls , Indicators and Connector Pin Assignments This chapter pro vides details of cont rols, indicato r s as well as connector pin assignments f or all connectors on th e A TCA-C 110/1G board. Face plate and LEDs The A TCA- C110/1G has two face plates, to p f ace plate and bottom f ac[...]

ATCA-C110/1G Installation and Use Manu al Chapter 5 Control s, Indicators and Connector Pin Assignments 52 REVIE W COPY Baseboar d Connectors The f ollowing sections describe the onboard connectors on A TCA- C110/1G base board. Figure 5-2 show s the location of the connect ors. ■ FIM Connectors ■ AMC Connectors ■ A TCA Backplan e Connectors T[...]

Chapter 5 Control s, Indicators and Connector Pin Assignments ATCA-C110/1G Installation and Use Manual 53 REVIE W COPY FIM Connectors The FIM connecto rs used on the baseboa rd are specially designed f or high-speed dif f erential signaling. T ab le 5-2 sho ws the f abr ic signals routed between the baseboard and FIM throu gh the connecto r . T abl[...]

ATCA-C110/1G Installation and Use Manu al Chapter 5 Control s, Indicators and Connector Pin Assignments 54 REVIE W COPY The f our FIM connectors: J1, J2, J3 and J4, onboard the A TCA-C110 /1G are described below . See Figure 5-2 on page 52 f or location of FIM co nnectors. 26 PICMG3.1, F abric Interf ace Gig SerDes Port 0 2 BCM56502 27 Gig SerDes P[...]

Chapter 5 Control s, Indicators and Connector Pin Assignments ATCA-C110/1G Installation and Use Manual 55 REVIE W COPY AMC4_SA T A0_TX+ S4+ 7 43 S22+ AMC4_PCIEXP_LANE1_ TX+ AMC4_SA T A0_TX- S4- 8 44 S22- AMC 4_PCIEXP_LANE1_TX- AMC4_SA T A1_TX+ S5+ 9 45 S23+ AMC4_PCIEXP_LANE2_TX+ AMC4_SA T A1_TX- S5- 10 46 S23- AMC 4_PCIEXP_LANE2_TX- AMC3_PCIEXP_LAN[...]

ATCA-C110/1G Installation and Use Manu al Chapter 5 Control s, Indicators and Connector Pin Assignments 56 REVIE W COPY T able 5-4. FIM Connector J2 Pinout Signal Pin Name Pin # Pin # Pin Name Signal AMC1_PCIEXP_LANE0_TX+ S1+ 1 37 S19+ AMC2_PCIEXP_LANE2_TX+ AMC1_PCIEXP_LANE0_TX- S1- 2 38 S19- AMC2_PCIEXP_LANE2_TX- AMC1_PCIEXP_LANE1_TX+ S2+ 3 39 S20[...]

Chapter 5 Control s, Indicators and Connector Pin Assignments ATCA-C110/1G Installation and Use Manual 57 REVIE W COPY AMC2_PCIEXP_LANE0_TX+ S17+ 33 69 S35+ PROC_GBE_POR T1_TX+ AMC2_PCIEXP_LANE0_TX- S17- 34 70 S35- PROC_GBE_POR T1_TX- AMC2_PCIEXP_LANE1_TX+ S18+ 35 71 S36+ PROC_GBE_POR T1_RX+ AMC2_PCIEXP_LANE1_TX- S18- 36 72 S36- PROC_GBE_POR T1_RX-[...]

ATCA-C110/1G Installation and Use Manu al Chapter 5 Control s, Indicators and Connector Pin Assignments 58 REVIE W COPY F ABRIC_LINK5_RX- S13- 26 62 S31- PEX_8114_PCIe_LANE1_TX- F ABRIC_LINK5_TX+ S14+ 27 63 S32+ PEX_8114_PCIe_LANE2_TX+ F ABRIC_LINK5_TX- S14- 28 64 S32- PEX_8114_PCIe_LANE2_TX- F ABRIC_LINK4_RX+ S15+ 29 65 S33+ PEX_81 14_PCIe_LANE3_T[...]

Chapter 5 Control s, Indicators and Connector Pin Assignments ATCA-C110/1G Installation and Use Manual 59 REVIE W COPY AMC Connectors The AMC modules are connected to the carrier boa rd via the AMC connectors . See Figure 5-2 on page 52 f or AMC connector locat ions. The AMC Connector has distinct regions f or interf acing various interf aces on th[...]

ATCA-C110/1G Installation and Use Manu al Chapter 5 Control s, Indicators and Connector Pin Assignments 60 REVIE W COPY Clocks The telecom synchroniza tion cloc ks from LCCB interf ace are routed to the AMC boards . The option f or the AMC Module to driv e the CLK3 to the A TCA backplane is pro vided for t he AMC Ba y3 and AMC Bay4. Common Options [...]

Chapter 5 Control s, Indicators and Connector Pin Assignments ATCA-C110/1G Installation and Use Manual 61 REVIE W COPY The SA T A por ts are mapped to the P ort 2 and P or t 3 of the AMC connect or as per the AMC .3 Specification . The ports from each of the AMC Ba ys are routed to the F abric Interf ace Module. Fat Pipes Region The F at Pipes Regi[...]

ATCA-C110/1G Installation and Use Manu al Chapter 5 Control s, Indicators and Connector Pin Assignments 62 REVIE W COPY A TCA Backplane Connector s The A TCA backplane conn ectors reside in the th ree zones 1 to 3 as specif ied by the A TCA standard and are called J10 , J20 to J23 and J30 to J31. Figure 5-3 shows the location of A TCA con nectors l[...]

Chapter 5 Control s, Indicators and Connector Pin Assignments ATCA-C110/1G Installation and Use Manual 63 REVIE W COPY Zone 1 Connectors The connector residing in Zon e 1 is called J10 (see Figu re 5-3 on page 62 ) and ca rries the f ollowing signals: ■ P ower f eed for the blade (ABP_ VM48_x_CON and ABP_R TN_A_CON) ■ P ower enable (ABP_ENABLE_[...]

ATCA-C110/1G Installation and Use Manu al Chapter 5 Control s, Indicators and Connector Pin Assignments 64 REVIE W COPY Zone 2 Connectors Zone 2 contains f our connectors: J20, J2 1, J22 and J23 (see Figure 5-3 on pag e 62 ) carrying the f ollowing types of signals: ■ T elecom clock signals (CLKx_) ■ Base interf ace signals (BASE_) ■ F abric [...]

Chapter 5 Control s, Indicators and Connector Pin Assignments ATCA-C110/1G Installation and Use Manual 65 REVIE W COPY T able 5-12. Zone 2 Bac kplane Connect or J21 Pinout - Rows A to D Pin # ABCD 1 Reserved Reserved T ermi nated T er minated 2 Reserved Reserved T ermi nated T er minated 3 Reserved Reserved T ermi nated T er minated 4 Reserved Rese[...]

ATCA-C110/1G Installation and Use Manu al Chapter 5 Control s, Indicators and Connector Pin Assignments 66 REVIE W COPY 7 Reserved Reser ved T er minated T er mina ted 8 Reserved Reser ved T er minated T er mina ted 9 Reserved Reser ved T er minated T er mina ted 10 Reser ved Reserved T er minated T er minated T able 5-15. Zone 2 Bac kplane Connect[...]

Chapter 5 Control s, Indicators and Connector Pin Assignments ATCA-C110/1G Installation and Use Manual 67 REVIE W COPY Zone 3 Connectors Zone 3 contains thre e connectors: J30, J31, and J32 ( see Figure 5-3 on page 62 ). The connectors are used to connect the R TM to the blade and carry the f ollowing signa ls: ■ Serial : debu g only ■ USB : de[...]

ATCA-C110/1G Installation and Use Manu al Chapter 5 Control s, Indicators and Connector Pin Assignments 68 REVIE W COPY T able 5-19. Zone 3 Bac kplane Connect or J30 Pinout - Rows E to H Pin # E F G H 1 IPMC_A TCA_RXD IPMC_A TCA_TXD IPMC_AMC_RXD IPMC_AMC_TXD 2 Reser ved Reser ved Reser ved Reser ved 3 Reser ved Reser ved Reser ved Reser ved 4 Reser[...]

Chapter 5 Control s, Indicators and Connector Pin Assignments ATCA-C110/1G Installation and Use Manual 69 REVIE W COPY 7 XA UI_LANE2_RX+ XA UI_LANE2_RX- XA UI_LANE3 _RX+ XA UI_LANE3_RX- 8 Reser ved Reser ved Reser ved Reser ved 9 Reser ved Reser ved Reser ved Reser ved 10 Reser ved Reser v ed XAUI_MDC XA UI_MDIO T able 5-21. Zone 3 Bac kplane Conne[...]

REVIE W COPY[...]

6 ATCA-C110/1G Installation and Use Manual 71 REVIE W COPY 6 Memor y Map and Registers This chapter describes the f ollowing mapping inf or mation f or the A TCA- C110/1G board: ■ Memory Maps on page 71 ■ Interrupt Mapping on page 72 ■ Shelf Management Registers (IPMI int erf ace) on page 73 ■ I2C Address Map f or MPC8540 on page 74 ■ I2C[...]

ATCA-C110/1G Installation and Use Manu al Chapter 6 Me mory Map and Regis ters 72 REVIE W COPY Interrupt Mapping All the interrupts gener ated on the A TCA-C110/1 G are wired to the inter rupt controller of the MPC8540 Pro cessor . The PC I interru pts from the PCI/ PCI-X to PCI-Expre ss Bridge, the GbE Ph y interrupts and the interrupt from the DP[...]

Chapter 6 Memory Map and Registers ATCA-C110/1G Installation and Use Manual 73 REVIE W COPY Shelf Management Registers (IPMI interface) F or details abou t accessing the IPMC via IPMI co mmands as well as Sensor Dat a Records (SDRs) and Field Replacea ble Un it (FR U) information pro vided by the blade , refer to the A TCA-C1 10/1G Preliminary IPMI[...]

ATCA-C110/1G Installation and Use Manu al Chapter 6 Me mory Map and Regis ters 74 REVIE W COPY I 2 C Address Map f or MPC8540 The de vices suppor ted by the Processo r MPC8540 I 2 C interf ace along with their I 2 C addresses are shown in T able 6-4 . I 2 C Resour ces The Address Map f or the I 2 C de vices on the Private I 2 C interf ace for the S[...]

Chapter 6 Memory Map and Registers ATCA-C110/1G Installation and Use Manual 75 REVIE W COPY T emperature Sensor Board T empe rature Sensor , LM75CIM 0x9E FIM Devices BIB - EEPR OM for F abric Interf ace Module Board Inf or mation Block EE PROM 0xAE I 2 C to GPIO De vice HotPlug control PCA9557PW 0x32 I 2 C ADC Onboard ADC, AD7997 0x41 T able 6-5. P[...]

ATCA-C110/1G Installation and Use Manu al Chapter 6 Me mory Map and Regis ters 76 REVIE W COPY T elecom CLK1 Buffer Enable Signals (Address: 0x38) 0 A TCA_CLK1A_EN Enables the Cloc k to be sourced to the Backplane on the CLK1A lines 0 - Disable 1 - Enable 1 A TCA_CLK1B_EN Enables the Cloc k to be sourced to the Backplane on the CLK1B lines 0 - Disa[...]

Chapter 6 Memory Map and Registers ATCA-C110/1G Installation and Use Manual 77 REVIE W COPY T elecom CLK2 Buffer Enable Signals (Address: 0x3A) 0 A TCA_CLK2A_EN Enables the Cloc k to be sourced to the Backplane on the CLK2A lines 0 - Disable 1 - Enable 1 A TCA_CLK2B_EN Enables the Cloc k to be sourced to the Backplane on the CLK2B lines 0 - Disable[...]

ATCA-C110/1G Installation and Use Manu al Chapter 6 Me mory Map and Regis ters 78 REVIE W COPY The A Tmega64-AMC micr o-controller Priv ate I 2 C interf ace is used f or the control of the AMC Ba ys and the R TM. The Address Map f or the I 2 C devices on the Priv ate I 2 C interf ace for the A Tmega64-AMC micro-contr oller is shown belo w: T elecom[...]

Chapter 6 Memory Map and Registers ATCA-C110/1G Installation and Use Manual 79 REVIE W COPY T able 6-7. Priv ate I 2 C Address Map - A Tmega64- AMC micro-contr oller Device Device description Address I 2 C to GPIO De vice AMC1 Control signa ls interf ace 0x30 I 2 C to GPIO De vice AMC2 Control signa ls interf ace 0x32 I 2 C to GPIO De vice AMC3 Con[...]

ATCA-C110/1G Installation and Use Manu al Chapter 6 Me mory Map and Regis ters 80 REVIE W COPY I 2 C to GPIO’ s Device Mappings - A TMega64-AMC Private I 2 C Bus T able 6-8. I 2 C to GPIO’ s Device Mappings - A T Mega64-AMC Priv ate I 2 C Bus Device Ad dress GPIO Number Description AMC Ba y x Control Interf ace 0 AMCx_P A YLO AD_PWR_EN# P ayloa[...]

Chapter 6 Memory Map and Registers ATCA-C110/1G Installation and Use Manual 81 REVIE W COPY R TM Control Signals 0R T M _ I M P B _ R D Y The IPMB isolator has completed the star t-up after enabling the de vice 0 - Star t-up Completed 1 - Star t-up Completed 1 R TM_IMPB_EN The IPMB Connection to RTM is enabled at the Isolator 0 - Disab le 1 - Enabl[...]

ATCA-C110/1G Installation and Use Manu al Chapter 6 Me mory Map and Regis ters 82 REVIE W COPY GPIO Geographical addressing of AMC Ba ys on A TCA- C110/1G Geogr aphical Addressing f or AMC Bays U : Unconnected P : Pulled up to Management P ower G : Grounded Ethernet Ph y Address Map The Manageme nt Interf aces of the Ethernet Ph ys are connected to[...]

A ATCA-C110/1G Installation and Use Manual 83 REVIE W COPY A T roub leshooting Err or List This appendix pro vides a hint list for detectin g erroneous system configu rations and an y untow ard or unusual beha vior of the A TCA-C110/1G. It cannot repla ce a serious and sophisticated pre- and post-sales suppo r t during application de velopment. If [...]

ATCA-C110/1G Installation and Use Manu al Appendix A Tro ubleshooting 84 REVIE W COPY During or After Sy stem Initialization Prob lem P o ssible Reason Solution The blue hot-s wap LED does not glow after inser ting the board. The board has no t mated completely with the backplane conne ctors. 1: Ensure that the boa rd is fully inser te d and seated[...]

Appendix A Troubleshooting ATCA-C110/1G Installation and Use Manual 85 REVIE W COPY During Boot-up Pr ocedure Prob lem P ossible Reason Solution The board seems to hav e powered up , but there are no boot-up prints on the console OR the boot-up prints halt mid wa y . Board is under reset or , is being reset per iodically . 1: Check if the carrier I[...]

ATCA-C110/1G Installation and Use Manu al Appendix A Tro ubleshooting 86 REVIE W COPY During Boar d Operation Prob lem P ossible Reason Solution Board runs unstable or hangs after some duration of operation. Disregard of environmental requirements 1: Check that internal system temperature remains within specifi ed ranges f or all system de vices. E[...]

Appendix A Troubleshooting ATCA-C110/1G Installation and Use Manual 87 REVIE W COPY RT M gets reset. Super capacitor is drained if the board has not been powered on f or a sufficient duration (more than 8 hours). P ower on the board and reconfigure th e R TM. W ait for at least ten minu tes for the super capacitor to charge. Board hangs or beco mes[...]

REVIE W COPY[...]

B ATCA-C110/1G Installation and Use Manual 89 REVIE W COPY B Specifications Specifications This appendix provides general mechanical, environmental and electrical specifications for the ATCA-C110/1G. En vironmental and Ph ysical Specifications The A TCA- C110/1G f eatures the industr y-standard A TCA form fa ctor . The conditions listed belo w refe[...]

ATCA-C110/1G Installation and Use Manu al Appendix B Spec ifications 90 REVIE W COPY T able B-1. A TCA- C110/1G En vironmental Specifications Characteristics Specifications En vironmental Parameter s A minimum of 300 LFM (linear feet per minute) of forced air cooling is recommended for operation in the higher temperature ranges. T emperature range [...]

Appendix B Specificatio ns ATCA-C110/1G Installation and Use Manual 91 REVIE W COPY P o wer Requirements The b lade’ s pow er requirements depe nd on the installed hard ware accessories . If y ou want to install accessories on the board, the load of th e respectiv e accessor y has to be added to that of the b lade. In the f ollowing tab le you wi[...]

ATCA-C110/1G Installation and Use Manu al Appendix B Spec ifications 92 REVIE W COPY Standar d Compliance The A TCA-C110/1G is CE appro ve d and meets the f ollowing standard req uirements: Note The A TCA-C110/1G is yet to be qua lified in the following standards . T able B-3. Standar d Compliance Standar d Description SN29500/8 MIL-HDBK-217F GR-33[...]

Appendix B Specificatio ns ATCA-C110/1G Installation and Use Manual 93 REVIE W COPY EMC Compliance The A TCA- C110/1G was tested in an EM C-compliant chassi s and meets the requiremen ts f or EN55022 Class A equipment. Compliance w as achiev ed under the f ollowing conditions: ■ Shielded cables on all exter nal I/O por ts ■ Cable shields connec[...]

REVIE W COPY[...]

C ATCA-C110/1G Installation and Use Manual 95 REVIE W COPY C Ther mal V alidation Thermal Requirements Board component temp eratures are aff ected b y ambient temperat ure, airflo w , board electrical operat ion and softw are operation . In order to e valuat e the thermal perf ormance of a circuit board assemb ly , it is necessary to test the board[...]

ATCA-C110/1G Installation and Use Manu al Appendix C Thermal Validation 96 REVIE W COPY Component T emperature Measurement The f ollowing sections outline gener al temperat ure measurement method s. F or the specific types of measur ements required f or thermal ev aluation of this board, see T able C-1 on page 95 . Preparation W e recommend 40 A WG[...]

Appendix C Thermal Validatio n ATCA-C110/1G Installation and Use Manual 97 REVIE W COPY If components are cov ered by mechanical par ts such as heatsinks, y ou will need to machine these par ts to route t he ther mocouple wir e. Mak e sure that the ther mocoup le junction cont acts only the electrical component. Also ma ke sure t h at heatsinks la [...]

ATCA-C110/1G Installation and Use Manu al Appendix C Thermal Validation 98 REVIE W COPY Measuring Local Air T emperature Measure local component ambient temper ature b y placing the thermocouple downstr eam of the compo nent. This meth od is conser v ative since it includes heating of th e air by the component. F igure C-2 illustrates one me thod o[...]

D ATCA-C110/1G Installation and Use Manual 99 REVIE W COPY D Related Documentation Embedded Comm unication s Computing Documents The Motorola pu blications listed below are ref erenc ed in this man ual. Y ou can obtain elec tronic copies of Motorola pub lications by contacting y our local Motorola sales office or by visiting ECC’ s World Wide We [...]

ATCA-C110/1G Installation and Use Manu al Appendix D Re lated Document ation 100 REVIE W COPY Manufacturer s’ Documents F or additional inf ormation, refer to the f ollowing table f or manuf acturers’ data shee ts or user’ s manuals . As an additional help , a source f or the listed document is pro vided. Please note that, while these source [...]

Appendix D Related Document ation ATCA-C110/1G Installation and Use Manual 101 REVIE W COPY Related Specifications F or additional inf or mation, ref er to the f ollowing table fo r related specifications . As an additional help , a source f or the listed document is pro vided. Please note that, while these sour ces ha ve been v erified, the inf or[...]

REVIE W COPY[...]

REVIE W COPY ATCA-C110/1G Installation and Use Manual 103 A AMC bay locations . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 ATCA-C110/1G block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 37 main functional blocks . . . . . . . . . . . . . . . . . . . . 37 overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[...]

REVIE W COPY[...]