Agilent Technologies 87020 Bedienungsanleitung

Agilent 8702D Lightwave Component Analyzer Installation Guide[...]

ii © Copyright Agilent T echn ologies 2000 All Rights Reserved. Repro- duction, adaptation, or trans- lation w ithout prior writ ten permi ssion is proh ibited, except as allowed under copy- right laws. Agilent P art No . 08702- 9005 5 Printed in U SA Apri l 2000 Agilent T echnolo gies Lightwave Division 1400 Fountaingrove Parkway Sant a Rosa, CA [...]

iii Insta llation at a G lance Installation at a Glance The proced ures in this b ook provid e step-by -step in struction s for instal ling the A gilent 8702D . Be sure to verify t he Agilent 8702 D’ s performance Chapter 2, “ Automa ted V e rificatio n ” , Chapter 3 , “ Manual V erifi cation ” , and Chapter 4, “ Performan ce T ests ”[...]

iv Gener al Sa fety Co nsid era tions General Safety Considerat ions This product has been designed and tested in accordance with IEC Publica- tion 61010-1 , Safety Requir ement s for Electrical Eq uipment for Measurem ent, Contro l and Laborato ry Use, and has been supplie d in a safe co ndition. The instruction d ocumentation co ntains info rmati[...]

v Certifica tion CAUTIO N Before s witching on this instrument , make sure that the l ine voltag e selec tor swit ch is set t o the lin e voltage o f th e power sup ply a nd the co rrect fuse is inst a lle d. Assur e the supply vol tage is in the spec ified rang e. CAUTIO N This pro duct is desi gned for use in In stallatio n Category II and Poll u[...]

vi Assistan ce Assis tance Product maintenance agreements and other customer assistan ce agreements are avai lable for Agil ent T echnologies produ cts. Fo r any assi stance, cont act your nearest Agi lent T ec hno logies Service Office.[...]

Contents Contents-1 1 Installi ng the Agile nt 8702D Step 1. Insp ect t he Ship ment 1-3 Step 2. Set up St atic-S afe W orksta tion 1-4 Step 3. Opt ion 1D5, Conne ct the Frequ ency Refer ence 1-6 Step 4. Che ck the Fuse and V olta ge Sele ction 1-7 Step 5 . Connect the L i ne-Power Cable 1-9 Step 6 . Connect a Keyboard 1-10 Step 7. T urn on th e Ag[...]

Conte nts -2 Conte nts 9. Calibr ation Coeffi cients 4-34 10. Syste m T race Noise (Only for Analyze rs with out Opti on 006) 4 -40 11. Syste m T race Noise (Only for Analyze rs with Option 00 6) 4-4 2 12. T est Port Input Imped ance 4-44 13. T est Port Receiver Magnitude D ynamic Accura cy 4-48 14. T est Port Receiver Phase Dynamic A ccuracy 4-55 [...]

Contents-3 Conten ts 9. Receiver Inp ut Crosstalk 6-26 10. Receiver T race Noise 6-33 11. Receiver In put Impedance 6-35 12. Receiver Magnitude Dynamic Accuracy 6-39 13. Receiver Phase Dynamic Accuracy 6-47 14. Receiv er Magn itude Compre ssion 6-4 8 15. Receiver Phase Compr ession 6-56 16. Source and Receive r Harmonics (O ption 002 Only) 6-62 17.[...]

[...]

1 Step 1. Insp ect th e Ship ment 1-3 Step 2. Set up St atic-S afe W orksta tion 1-4 Step 3. Opt ion 1D5, Conne ct the Frequ ency Refer ence 1-6 Step 4 . Check the Fuse and V oltage Selec t ion 1-7 Step 5 . Connect the L i ne-Power Cable 1-9 Step 6 . Connect a Keyboard 1-10 Step 7. T urn on th e Agilent 870 2D 1-11 Step 8. Connect a Prin ter or Plo[...]

1-2 Instal ling the Agil ent 8702D Instal ling the Agile nt 8702 D Installing the Agilent 8702D The instr uction s in this chapter show y ou how to inst all your Ag ilent 8702 D. Y ou sho uld be abl e to fini sh these p rocedures in about ten to twenty minut es. Refer to “ Specific ations and Regul atory Inf ormation ” , in the Agilent 8702D Re[...]

1-3 Installi ng the Agile nt 8702D Step 1 . Inspect the Shipment Step 1. Inspect the Shipment 1 Verify t hat all components or dered have arrived by comparing the ship ping forms to the ori ginal purchase order. Ins pect all shippi ng containe rs. If you r shipment is damaged or incompl ete, save the pa cking mate rials and no- tify bo th the sh ip[...]

1-4 Instal ling the Agil ent 8702D Step 2. Set up Sta tic-Safe Wo rkstation Step 2. Set up Static-Safe Workstation Electro static d ischarge (ESD ) can dama ge or des troy th e input cir cuits of the Agilen t 8702D. E SD can also damage or d estroy elect ronic compo nents tha t you are measuri ng. All work should be per formed at a static-safe work[...]

1-5 Installi ng the Agile nt 8702D Step 2. Set up Sta tic-Safe W orkstatio n Both typ es, when use d toge ther , provid e a sig n ific ant l evel of ESD pro tection. Of th e two, o n ly t he ta ble-mat and wr ist-stra p co mbin ation pro v id es ade quate ESD p rotect ion wh en used alon e. T o en sure use r safety , the s tatic-safe access ories m[...]

1-6 Instal ling the Agil ent 8702D Step 3. Opt ion 1D5, Connec t the Freq uency Reference Step 3. Option 1D5, Connect th e Frequency Reference If your inst rument has the opti onal high st abilit y freque ncy refer ence insta lled, conn ect t he jumpe r cable on the Ag ilent 8702D re ar panel as show n in Figure 1-2 . Figure 1-2. Jumper Cable Conne[...]

1-7 Installi ng the Agile nt 8702D Step 4. Check the Fuse an d V o lt age Sele ction Step 4. Check the Fuse and Voltage Selection 1 Locat e the line-input c onn ector o n th e inst rument ’ s rear pa nel. 2 Discon nect the l ine-power ca ble i f it is co nnected. 3 Use a small flat-blade screwdriv er to open the p ull-ou t fu se dra wer. WAR NI N[...]

1-8 Instal ling the Agil ent 8702D Step 4. Ch eck the Fu se and Volt age Selec tion WAR NI N G For con tinued protec tion again st fire h azard, re place l ine fuse on ly with same ty p e and rat ings, (type T 3A/ 250V for 100/2 40V operation). The use of o ther fu ses or materi als is pr ohibi ted. 5 Set the rea r panel line -voltag e select or to[...]

1-9 Installi ng the Agile nt 8702D Step 5. Co nnect the L ine-Power Cable Step 5. Connect the Line-Power Cable CAUTIO N Always use the thre e-prong AC power cord sup p lie d with thi s instrument . Failur e to ensu re adequat e earth gro unding by not using thi s cord may caus e instru ment damag e. CAUTIO N Do not connect ac power until you have v[...]

1-10 Instal ling the Agil ent 8702D Step 6. Co nnect a Key board Step 6. Connect a Keyboard • If y o u pl a n to use a keyboard with your Agil ent 8702D, connec t it now to the instr ument ’ s rear-panel k eyboard conne c tor . Figure 1-6. Rear Panel Peri pheral Connections[...]

1-11 Installi ng the Agile nt 8702D Step 7. T urn on th e Agilent 87 02D Step 7. Turn on the Agilent 8702D 1 Press th e front-pa nel LINE key. Refe r to Fig ure 1-7 . The f ront-panel LINE switch di sconnects the mai ns circui ts from the mai ns sup- ply af ter t he EMC filt ers and before othe r parts of the in strume nt. 2 If th e Agilent 8 702D [...]

1-12 Instal ling the Agil ent 8702D Step 8 . Connect a Printer or Plotte r Step 8. Connect a Printer or P lotter 1 Connect a print er or plotte r to the cor responding interface port. Refer to Figure 1-6 on page 1-10 for the appr opriate re a r pan el connect ion. 2 If yo u are u sing th e parallel i nterface, p ress LOCAL and then PA RA L L EL un [...]

1-13 Installi ng the Agile nt 8702D Step 9. If Y ou Co nnect a Pri nter Step 9. If You Connect a Printer 1 Press LOCAL , SET ADDRESSES , PRINTER PORT . 2 Press th e key that corre sponds to the p rinter inte rface: HPIB , PA R A L L E L (pa ralle l port), or SERIAL (seria l port). 3 If you sel ected HPIB , the GPIB ad dress is active s o you can t [...]

1-14 Instal ling the Agil ent 8702D Step 10. If Yo u Connec t a Plot ter Step 10. If You Connect a Plotter 1 Press LOCAL , SET ADDRESSES , PLOTTER PORT . 2 Press t he key that co rresp o nds t o the p lott er interfac e: HPIB , PA R A L LE L (parallel port), or SERIAL (seria l port). 3 If you sel ected HPIB , the GPIB ad dress is active s o you can[...]

1-15 Installi ng the Agile nt 8702D Step 11. Set the C lock Step 11. Set the Clock 1 Press SYSTEM , S ET CLOCK to begin setting and activating the time stamp feature so t h e A gilent 8702 D pl aces the t ime and d ate o n your har dcopies and disk director ies. 2 Press the appr opriat e softke y to s et the tim e and date . 3 Press ROUND SECONDS w[...]

1-16 Instal ling the Agil ent 8702D Step 12. Chec k the Ope rati on Step 12. Chec k the Ope ration If yo ur in strument i s an Agilent 87 02D Op tion 0 11, s kip this st ep and con tinu e with “ Step 13. Check the Operatio n (Optio n 011) ” on page 1- 21 . 1 Turn off the LINE power switc h. Then , turn ba ck on the LINE pow er swi tch . 2 Locat[...]

1-17 Installi ng the Agile nt 8702D Step 12. Check t he Oper ation Figure 1-10. Operation Check Connections 5 Press PRESET , SYSTEM , SERVICE MENU , TESTS , EXTERNAL TESTS , EXECUTE TEST . 6 Follow th e prompts shown on the display, and then pr ess CO NTIN UE . 7 Press th e up-arrow key, EXECUTE TEST , and then follow the pro mpts shown on the dis [...]

1-18 Instal ling the Agil ent 8702D Step 12. Chec k the Ope rati on Figure 1-11. Transmission Mod e Conne ctions 9 Press CHAN 2 to check the forward transmi ssion mode for channel 2. Look at the measurem ent trace disp layed on the Agilen t 8702D . It should b e similar to the trace shown in Figur e 1-12 . The A gilent 8702D displ ay sh own in Figu[...]

1-19 Installi ng the Agile nt 8702D Step 12. Check t he Oper ation Figure 1-13 . Figure 1-13. Reverse Transmission Display 11 Connec t t he equ ipm ent as show n in Figure 1-14 and pr ess PRESET . Figure 1-14. Transmission Load Match C onnections 12 Look at the meas urement tr ace display ed on the Ag ilent 8702D. It should be simila r to the tra c[...]

1-20 Instal ling the Agil ent 8702D Step 12. Chec k the Ope rati on Figure 1-15. Forward T ransmission Mode 13 Press MEAS, Refl: E S22 REV to c heck the r evers e reflect ion mode fo r ch annel 1. The me asuremen t trace should be s i milar to Figure 1-16 . Figure 1-16. Reverse Ref lection Mode 14 Continual wi th “ Step 14. Copy the EEPRO M Disk [...]

1-21 Installi ng the Agile nt 8702D Step 1 3. Check t he Opera tion (Op tion 011) Step 13. Check t he Operation (Option 011) An Agi lent 8 5047A S-paramete r test se t must be us ed when making meas ure- ments. 1 Turn off the LINE power switc h. Then , turn ba ck on the LINE power switc h . 2 Locate the ser ial numbe r and configur ation opti ons s[...]

1-22 Instal ling the Agil ent 8702D Step 13. Chec k the Ope ration (Opti on 011) Figure 1-18. Operation Check Connections 5 Press PRESET , SYSTEM , SERVICE MENU , TESTS , EXTERNAL TESTS , EXECUTE TEST . 6 Follow the prompts show n on t he dis play, a nd the n pr ess CON TINUE . 7 Press th e up-arrow key, EXECUTE TEST , and then fo llow the promp ts[...]

1-23 Installi ng the Agile nt 8702D Step 1 3. Check t he Opera tion (Op tion 011) Figure 1-19. Transmission Mod e Conne ctions 9 Press CH2 to check the forward tr ansmission m ode for channel 2. Look at the measu rement trace displ ayed on t he analyzer. It sho uld be s imilar to the trace shown in Fig ure 1-20 . The an alyzer dis play sh o wn i n [...]

1-24 Instal ling the Agil ent 8702D Step 13. Chec k the Ope ration (Opti on 011) 10 Press MEA S and then T rans: E/E S12 REV to check t he reverse transmis sion mode for channel 2 . The measure ment trace sh ould be similar to the trace sh own in Figure 1-21 . Figure 1-21. Reverse Transmission Display 11 Connec t t he equ ipm ent as show n in Figur[...]

1-25 Installi ng the Agile nt 8702D Step 1 3. Check t he Opera tion (Op tion 011) Figure 1-23. Forward T ransmission Mode 13 Press MEAS , Refl: E S22 REV to check the reve rse ref lection mo de for cha nnel 1. The me asuremen t trace sho uld be simila r to Figure 1-24 . Figure 1-24. Reverse Re flection M ode[...]

1-26 Instal ling the Agil ent 8702D Step 14. C o py th e EEPROM Disk Step 14. Copy the EEPROM Disk The A gilent 87 02D is ship ped from t he facto ry wit h an EEPROM backup di sk which is unique to each instrume nt. The backup disk contains a copy of cor- rect ion c onst ants whic h wer e st ored in the ins trumen t ’ s internal memor y at the f [...]

2 Step 1. I nitial iza tion 2-3 Step 2 . Measu rement Calibra tion 2-4 Step 3. Device Ve rification 2-6 In Case of Difficul ty 2-9 Automa ted Verifi cation[...]

2-2 Automated V erification Automate d Performan c e Verifica tion Automated Performance Verification The auto mate d perfor mance ve rificati on proce dure in this chapt er provi de a high level of c onfiden ce that t he Agilent 8702D is wo rking proper ly . Althoug h this procedure is automa ted, it does not require a comput er . How eve r , you [...]

2-3 Automated V e rification Step 1. Initializatio n How to select the s y stem veri fication procedure Check to see how th e verif ication kit fl oppy disk is la bele d: • If t he di sk is lab eled V e rification Da ta Disk , pr oceed with the Ag ilent 8702 D Auto- mated Mode System Ve rifica tion in th is chapter. • If th e disk i s labeled V[...]

2-4 Automated V erification Step 2. Me asurement Calibration 3 Insert the verificat ion kit disk into the Ag ilent 87 02D ’ s disk dr ive. 4 Press PRESET , SAVE/REC ALL , SELECT DISK , INTERNAL DISK . 5 If you w ant a printou t of t he verifi cation data for all the devices, p ress SYSTEM , SERVICE MENU , TEST OPTIO NS , RECORD ON . If you swi tc[...]

2-5 Automated V e rification Step 2. Meas urement Cali bration Figure 2-2. Connections f or Mea surement Cal i bration Standards 5 Press F ORW ARD:OPEN . 6 When the A gilent 8 702D finis hes measur ing the st andard, conne ct the “ short ” end of the open /short comb ination to refe rence tes t port 1 . 7 Press F ORWARD:SHORT . 8 When t he Agil[...]

2-6 Automated V erification Step 3 . Device Ve rificat ion 17 Con nect th e test port c ables as sho wn Figur e 2-3 . Figure 2-3. Transmission Cali b ration Setup 18 Press TR ANSM ISSION , F WD TRANS THRU . 19 When the Agilen t 8702D f inishe s the measureme nt, pre ss FWD MA TCH THRU . 20 When the Agilen t 8702D f inishe s the measureme nt, pre ss[...]

2-7 Automated V e rification Step 3. De vice V erification each S -paramete r meas ureme nt. • If you switch ed the record functi on on , the Agilent 8702D measur es all S-pa - ramet ers (magn itude and phas e) w it hout pau sing. Also, the Agilen t 8702D only di splays and pri nts the pass /fail in formatio n for the S-paramete r me a- surements[...]

2-8 Automated V erification Step 3 . Device Ve rificat ion of the verification mi smatch t o refere nce test p ort 1. Figure 2-6. Mismatch Devic e Verificati on Setup 7 Press RETURN , TESTS , 30, x1 , EXECUTE TEST , CONTINUE . 8 When t he Agil ent 8 702D fini shes a ll th e measu rements, c onnec t the mismatch verification de vice, as shown in Fig[...]

2-9 Automated V e rification In Case of Difficulty 10 You h ave com pleted the sy stem verifi cation proc edure when th e Agilent 8702D disp lays, Ver Def 4 DONE . In Case of Difficulty 1 Inspect all conne ctions. Do not dis connect th e cable s from the A gilent 8 702D test ports. Doi n g so will inval idate the ca libr ation that you ha ve done e[...]

[...]

3 Step 1. I nitial iza tion 3-2 Step 2 . Measu rement Calibra tion 3-4 Step 3. Device Ve rification 3-5 In Case of Difficul ty 3-9 Manual Veri ficati on[...]

3-2 Manual Veri fication Manual Per formance Verificat ion Manual Performance Verification The manual perform ance verificati on procedur e in this chapt er provide s a high le vel of confide nce that the Agi lent 8 702D is workin g properly . If yo u can locat e the Agil ent 8702D Verification D ata Disk , perform the automated vers ion in stea d,[...]

3-3 Manual Verification Step 1. Initializatio n Figure 3-1. System Verification Test Setup 2 While the eq uipment is w a rmi ng up, r eview the conn ector care infor mation in the Agilent 870 2D User ’ s Gui de . 3 Set up the syst em to pr int the verifi cation data : a Press LOCAL , SYSTEM CONTR OLLER . b Press SET A DDRESSES , PRINTER PORT . c [...]

3-4 Manual Veri fication Step 2. Me asurement Calibration CAUTIO N Do not press PRES ET or reca ll another instr ument state. Y ou must use the inst rument state tha t you loade d during the init ialization procedu r e. Step 2. Measurem ent Cali bration 1 Press MENU , POWER , – 2 , x1 to set the Agilen t 8702D t est po rt power t o – 2 dBm. 2 P[...]

3-5 Manual Verification Step 3. De vice V erification 18 Con nect th e test por t cables toge ther as sh own in Figure 3-2 . Figure 3-2. Transmission Cali b ration Setup 19 Press TR ANSM ISSION , FWD TRANS THRU . 20 When t he Agil ent 8702 D fini shes mea surin g the standar d, pres s FWD MA TCH THRU . 21 When t he Agil ent 8702 D fini shes mea sur[...]

3-6 Manual Veri fication Step 3 . Device Ve rificat ion Figure 3-3 . Figure 3-3. Connections for the 20 dB Verification Device 3 Press CONTINUE to run the test. 4 Press MENU , PO WER , –2 , x1 , CAL , CORREC TION ON . 5 Press COPY , PRINT MONOCHROME to obtain th e graphical represen tatio n of the measurem ent. 6 Press COPY , LIST , PRINT ALL MON[...]

3-7 Manual Verification Step 3. De vice V erification tude and pha se for t he four S-p aram eters). 10 When th e Agilent 8702D disp lays, Ver Dev 1 FAIL , pr oceed to th e next s tep only i f all the tested S-parame ter meas urements show a PASS st atus after yo u activate error corre ction i n Step 8 . Otherwi se, refer to “ In Case of Difficul[...]

3-8 Manual Veri fication Step 3 . Device Ve rificat ion Figure 3-5. Mism atch Device Verific ation Setup 17 Press TESTS , 30 , x1 , EXECUTE TEST , CONTIN UE . Ignore the error mess age. 18 Press MENU , PO WER , – 2 , x1 , CAL , CORR ECTION ON . 19 Repeat Step 5 throu gh Step 8 u ntil yo u have mad e all the S- parame ter measurements for th e ver[...]

3-9 Manual Verification In Case of Difficulty Figure 3-6. Mismatch Devic e Verificati on Setup 22 Press TESTS , 31 , x1 , EXECUTE TEST , CONTINUE . Igno re th e displaye d erro r message. 23 Press MENU , PO WER , – 2 , x1 , CAL , CORR ECTION ON . 24 Repeat Step 5 throu gh Step 8 u ntil you have made all the S- paramete r measurements for th e ver[...]

3-10 Manual Veri fication In Case of Difficulty a Press PRESET , SAVE/REC ALL , SELECT DISK , I NTERNAL MEMORY , RETURN . b Use th e front panel kno b to highl ight t he calib ratio n you want to recall and press REC ALL STA TE . c Press MENU , TRI GGER MENU , CO NTINUOU S to t r igge r the co ntinu ous sweep s. d Con nect th e short to refe rence [...]

4 1. Test Port Output Freq uency Range and Accuracy 4-3 2. Exter nal Sour ce Mode Frequency Range 4-5 3. Test Port Output Powe r Accuracy 4-6 4. Test Port Output Powe r Range and Line arity 4-8 5. Minimum R Channel Level 4-10 6. Tes t Port Input Noise Floor L evel 4-15 7. Test Port In put Fre quency Respons e 4- 19 8. Test Port Cr ossta lk 4-29 9. [...]

4-2 Performanc e Tests Manua l Performa nce Tests Manual Performance Tests This chapter c ontain s procedur es which te st the elec tric al performa nce of the Agilent 8702D. If yo u are us ing an Agilent 8702D O ption 01 1, pe rform the tests in C hapte r 6, “ Performance T ests – Option 011 ” . Before s tartin g these procedure s, allow th [...]

4-3 Performance T ests 1. T est P ort Ou tput Fre quenc y Rang e and Accu rac y WAR NI N G Any servi cing, adjustme nt, maintena nce, or re p air of this p r oduct must be per forme d only by qualified p ersonn el. Repai r infor mation provided in the In Cas e of Difficulty sectio ns o f this chap ter are provided for quali fied servi ce perso nnel[...]

4-4 Performanc e Tests 1. Test P ort Outp ut Freq uenc y Range an d Accu racy Figure 4-1. Test Port Outpu t Frequency Ran ge and Accuracy Test Setup 2 Press PRESET , MEN U , CW F REQ . 3 Press 30 , k/m and w rite the frequency counter reading on th e “ Performance Test R ecord. ” 4 Repeat Step 3 for each inst rument fr equency li sted in t he ?[...]

4-5 Performance T ests 2. Ex terna l Sou rce M ode Freque ncy Ra nge 2. External Source Mode Frequency Range Perfo rm this te st to ve rify that the analyzer ’ s refere nce chann el, input R, is capable of phase lockin g to a n ext ernal CW sig nal. Requi red Equipment Extern al Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[...]

4-6 Performanc e Tests 3. Test Port Output Power Accuracy 5 Check t o see if the anal yzer is phas e locki n g to the e xternal CW signal: • If the a nalyzer displ ays any phase lock err or messages, wr ite “ unlock ” in the “ Perform ance Test Re cord ” for the s et CW s ignal. • If the anal yzer does not displ ay any phase lo ck error[...]

4-7 Performance T ests 3. T est Po rt Output Power Accuracy Procedure 1 Zero and cali brate the powe r meter. Fo r more in formatio n of how to perfo rm this task, re fer to the powe r meter operati ng manual. 2 Connec t t he equ ipm ent as show n in Figure 4-3 . Figure 4-3. Source Outp ut Power Accuracy Test S etup 3 Press PRESET .[...]

4-8 Performanc e Tests 4. Tes t Port Out put Power Rang e and Li neari ty 4 Press MENU , CW FREQ , 300 , k/m . Set the calibration factor on the power meter for this CW frequency. 5 Write the power meter reading on the "Performance Tes t Record." 6 Repeat Step 4 and Step 5 fo r each CW fr equency list ed in the "Perfor mance Test R e[...]

4-9 Performance T ests 4. T e st Port Output Power Ra nge an d Lineari ty serv ice manual for mor e infor matio n on how to do this task. 2 On the an alyzer, press PRESET , MENU , CW FREQ , 300 , k/m . Set th e po wer me ter calibrat ion factor for this CW fre quency. 3 Connec t t he equ ipm ent as show n in Figure 4-4 . Figure 4-4. Test Port Out p[...]

4-10 Performanc e Tests 5. Minimum R Channel Level 6 Write the p ower mete r rea d ing i n the "Resu lts Me asured" colu mn on t he "Performance Test Record." 7 Calculate th e differe nce betwee n the analyzer te st port powe r (which appear s on the analyzer ’ s display) an d the power meter readin g. Write the re sult in th [...]

4-11 Performance T ests 5. Minimum R Channel Level Requi red Equipment For 50 Ω Analyzers Adapter, APC-3.5 (m) to APC-7 . . . . . . . . . . . . . . . . . Ag ilent P/N 1250-1746 Cable, APC-7 24- inch . . . . . . . . . . . . . . . . . . . . . . . . . . Ag ilent P/N 8120-4779 For 75 Ω Analyzers (Option 075) Minimum Loss Pad, 50 Ω to 75 Ω . . .[...]

4-12 Performanc e Tests 5. Minimum R Channel Level 8 If the ana lyzer di splays a phase loc k error mes sage, continu e increasing the test port power un til phase lock is achieved. 9 Write the test port pow er, th at is displ ayed on the a n alyzer , on the "Performance Test Record." 10 Repeat Step 5 throu gh Step 9 fo r the other CW fre[...]

4-13 Performance T ests 5. Minimum R Channel Level CAUTIO N Loop the W8 cable around the A5 samp ler as shown in Figure 4-6 . Do not push the ca ble down next to th e A11 phase lock assemb ly . Figure 4-6. Flexible RF Ca ble Location 2 Using an ohmme ter, verify tha t the RF cable is not op en. In add ition , examine both the cable connectors - mea[...]

4-14 Performanc e Tests 5. Minimum R Channel Level 3 Check t he R s a mpler by sub s titu ting i t with the B s ampler (A6). a Move ca ble W8 to t he B sampler (A6), as sho wn in Figu re 4-7 . Figure 4-7. Connectio ns for Substi tuting the R S ampler (A4) 4 Connec t t he equ ipm ent as show n in Figure 4-8 . Figure 4-8. Setup for Checking the R Sam[...]

4-15 Performance T ests 6. T est Po rt Input Noise Flo or Level 5 Repeat the t est, but s elec t the B samp ler (A6) by pres sing MEAS , INP UT PORTS , B in St ep 2 . Use the followi ng sp ecifications: 300 kHz to 3 GHz < – 27 dBm 3 GHz to 6 GHz < – 22 dBm 6 If th e analyz er fails the te st, repl ace the A11 as sembly. 7 Verif y that the[...]

4-16 Performanc e Tests 6. Test Port In put Noise Floo r Level 2 Press PRESET , MEN U , POWER , – 85 , x1 , STOP , 3 , G/n . 3 Press MEA S , INPUT PORTS , A , TESTPORT 2 , FORM A T , LIN MA G , SCALE REF , AUTO SCAL E . 4 Press MARKER FCTN , MARKER MODE MENU , ST A TS ON , ME NU , TRIGGER MENU , SINGLE . 5 When th e analyzer fi nishes t he sweep,[...]

4-17 Performance T ests 6. T est Po rt Input Noise Flo or Level Power ( dBm ) = 20 * [log 10 ( linear magnitude mean value )] 17 Write this calculate d value on the "Performance Test Record." Port 2 Noise Floo r Level from 50 kHz to 3 GHz (IF B W = 3 kHz) 18 Press AV G , IF B W , 3 , k/ m to change the IF bandw idth to 3 kHz. 19 Press MEN[...]

4-18 Performanc e Tests 6. Test Port In put Noise Floo r Level Port 1 Noise Floo r Level for 3 G Hz to 6 GHz (IF B W= 10 Hz) 34 Press MEAS , INPUT PO RTS , A , TESTPORT 2 . 35 Press MENU , TRI GGER MENU , SINGLE . 36 When t he analyze r finishes the sw eep, notice th e mean value. 37 Conver t the meas ured linear magn itude mean v alue to log magn [...]

4-19 Performance T ests 7. T e st Port Input Frequenc y Response 7. Test Port Input Frequency Response Perfo rm this te st to exa mine the v ector sum o f al l test se tup error vect ors in both magnit ude and pha se change as a func tion of freq uency . Requi red Equipment For 50 Ω Analyzers Power Mete r . . . . . . . . . . . . . . . . . . . . .[...]

4-20 Performanc e Tests 7. Test Port In put Frequenc y Respons e Figure 4-10. Setup for Power M eter Calib ration on T est Port 1 3 Press PRESET , ST AR T , 300 , k/ m . 4 Only for Analyzers with Option 006: Press STO P , 3 , G/n . 5 Press LOCAL , SYSTEM C ONTROLL ER . 6 Press SET ADDRESSES an d PO WER M TR until the analyze r shows the cor rect po[...]

4-21 Performance T ests 7. T e st Port Input Frequenc y Response 8 Press MENU , NU MBER of POINTS , 51 , x1 . 9 Press PO WER , PW R RAN GE MA N to turn th e auto power rang e off. 10 Press PO RT POWER to uncoupl e the test port output power. 11 Press CAL , PWRMTR CAL . 12 Press LOSS/SENSR LI STS , CAL FA CTOR SENSOR A . Refer to the back of the pow[...]

4-22 Performanc e Tests 7. Test Port In put Frequenc y Respons e a From t he sensor ca libration factor ent r ies menu, press ADD . b Press FREQUENC Y , 100 , k/m . If you make an entr y erro r, press ← and re-enter the correct value again. c Press CAL FACTOR , 96. 4 , x1 . d Press DONE to term inate t he first calibration factor data poin t entr[...]

4-23 Performance T ests 7. T e st Port Input Frequenc y Response T est Port 2 Input Frequ ency Response from 300 kHz to 3 GHz 16 Connec t t he equ ipm ent as show n in Figure 4-11 . Figure 4-11. Test Port 2 Input Freq uency Response Test Se tup 17 Press MEAS , INPUT PO RTS , B . 18 Press SCALE REF , SCALE/D IV , 1 , x1 . 19 Press MARKER , MARKER 1 [...]

4-24 Performanc e Tests 7. Test Port In put Frequenc y Respons e Power Meter Calibrati o n on Port 2 from 300 kHz to 3 G Hz 22 Connec t t he equ ipm ent as show n Fig ure 4-12 . Figure 4-12. Setup for Power M eter Calib ration on T est Port 2 23 Press MEAS , INPUT PO RTS , TESTPORT 2 . 24 Press CAL , PWRMTR CAL , ON E SWEEP , T AKE CAL SWEEP to sta[...]

4-25 Performance T ests 7. T e st Port Input Frequenc y Response 25 When the anal yzer dis plays the me ssage , P OWER METER CALIBRATION SWEEP DONE , con nect the eq uipm ent as shown as in Figure 4-13 . Figure 4-13. Test Port 1 Input Freq uency Response Test Se tup T est Port 1 Input Frequ ency Response from 300 kHz to 3 GHz 26 Press MEAS , INPUT [...]

4-26 Performanc e Tests 7. Test Port In put Frequenc y Respons e Figure 4-14. Setup for Power M eter Calib ration on T est Port 2 33 Press ST ART , 3 , G/n , STOP , 6 , G/n . 34 Press CAL , PWRMTR CAL . 35 Press LOSS/SENSR LI STS , CAL FA CTOR SENSOR B . Repeat St ep 10 to build a calibrat ion factor sensor table for the Ag ilent 8481A powe r sens [...]

4-27 Performance T ests 7. T e st Port Input Frequenc y Response T est Port 1 Input Frequ ency Response from 3 GHz to 6 GH z 39 When the analyze r finis h es the c alibra tion sweep, connect the equip ment as shown in Fig ure 4-15 . Figure 4-15. Setup for T est Port 1 Input Frequency Response 40 Press MEAS , INPUT PO RTS , A . 41 Press MARKER , MAR[...]

4-28 Performanc e Tests 7. Test Port In put Frequenc y Respons e Figure 4-16. Setup for Power M eter Calib ration on T est Port 1 45 Press MEAS , I NPUT PORTS , TESTPORT 1 . 46 Press CAL , PWRMTR CAL , ONE S W EEP , T AKE CAL SWEEP to start the power meter calibrat ion for output test p ort 1. T est Port 2 Input Frequ ency Response from 3 GHz to 6 [...]

4-29 Performance T ests 8. T est Port Crossta lk Figure 4-17. Test Port 2 Input Freq uency Response Test Se tup 48 Press MEAS , INPUT PO RTS , B . 49 Press MARKER , MARKER 1 , MARKER FCTN , MARKER MODE MENU , MKR SEA RCH , SEARC H:M IN . 50 Press MARKER , MARKER 2 , MARK ER FCTN , MAR KER MODE MENU , MKR SEA RCH , SEARC H:MAX . 51 Write the marker [...]

4-30 Performanc e Tests 8. Test Port C rosstal k Requi red Equipment For 50 Ω Analyzers Calibrati on Kit, 7 mm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Agile nt 85031B Cable, APC-7 24- inch . . . . . . . . . . . . . . . . . . . . . . . . . . . Ag ilent P/N 8120-477 9 For 75 Ω Analyzers Calib ration Kit, 75 Ω , Ty pe-N[...]

4-31 Performance T ests 8. T est Port Crossta lk Crosstalk to T est Port 2 fr om 300 kHz to 3 GHz 4 Press ST ART , 300 , k/m , STO P , 3 , G/n . 5 Press MEAS , T rans: E/E S21 FWD . 6 Press SCALE REF , REFEREN CE V ALUE , – 100 , x1 . 7 Press MENU , TRI GGER MENU , SINGLE . 8 Press MARKER FCTN , MARKER MODE MENU , MKR SE ARCH , SEARCH: MAX . 9 Wr[...]

4-32 Performanc e Tests 8. Test Port C rosstal k In Cas e of Difficulty WAR NI N G These servicing instructions are for use by quali f ied personnel o nly. To avoi d electr ical s hock, d o not p erform a ny servic ing unl ess you are qualified to d o so. WAR NI N G The opening of covers or r emoval of part s is likely to exp o se dangerous v oltag[...]

4-33 Performance T ests 8. T est Port Crossta lk Figure 4-19. Agilent 8702D Bottom Vi ew[...]

4-34 Performanc e Tests 9. Calibratio n Coefficients 9. Calibration Coefficients Perfo rm this pro cedure to ve rify the analyz er unc orrec ted te st port cha r act er- istic s. Requi red Equipment For 50 Ω Analyzers Calibrati on Kit, 7 mm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Agile nt 85031B Cable, APC-7, 24-in ch . [...]

4-35 Performance T ests 9. Calibra tion Coefficients 2 Press PRESET , ST AR T , 300 , k/ m . 3 Press CAL , CAL KI TS & STDS , SELE CT CAL KI T , CAL KIT : 7mm , RETURN , RETURN , CALI BRA TE ME NU , FU LL 2 -PORT . 4 Press ISOLA TION , O MIT ISOLA TION , ISOLA TION DONE . 5 Con nec t the “ open ” end o f th e open/ s hort combi nation (supp[...]

4-36 Performanc e Tests 9. Calibratio n Coefficients Figure 4-21. Transmission Cali bration Test Setup 19 Press TR ANSM ISSION , FW D TRANS TH RU . 20 When the analy zer fi nish es t he me asure ment, pres s FWD MA TCH THRU . 21 When the analy zer fi nish es t he me asure ment, pres s REV TRANS TH RU . 22 After the analyzer fi nishes the measur eme[...]

4-37 Performance T ests 9. Calibra tion Coefficients T ransmission T racki ng (Forward) Calibration C oefficient 31 Press SYSTEM , SERVICE M ENU , TESTS , 37 , x1 , EXECUTE TEST . 32 When the analy zer fi nish es th e tes t, r epeat Step 25 throug h Step 2 8 . Reflection T racking (Forwar d) Calibration Coeffi cient 33 Press SYSTEM , SERVICE M ENU [...]

4-38 Performanc e Tests 9. Calibratio n Coefficients 40 Press PRESET , ST AR T , 300 , k/ m . 41 Press CAL , CAL KI TS & STDS , SELE CT CAL KI T , CAL KIT : 7mm , RETURN , RETURN , CALI BRA TE ME NU , FU LL 2 -PORT . 42 Press ISOLA TION , OM IT ISOLA TION , IS OLA TION DONE . 43 Con nec t the “ open ” end o f th e open/ s hort combi nation [...]

4-39 Performance T ests 9. Calibra tion Coefficients Figure 4-23. Transmission Cali bration Test Setup 57 Press TR ANSM ISSION , FW D TRANS TH RU . 58 When the analy zer fi nish es t he me asure ment, pres s FWD MA TCH THRU . 59 When the analy zer fi nish es t he me asure ment, pres s REV TRA NS THR U . 60 When the analy zer fi nish es t he me asur[...]

4-40 Performanc e Tests 10. Syst em Trace N oise (O nly fo r Analyze rs withou t Opti on 006) Source Match (R everse) C alibratio n Coeffi cient 69 Press SYSTEM , SERVICE M ENU , TESTS , 39 , x1 , EXECUTE TEST . 70 When the analy zer fi nish es th e tes t, r epeat Step 63 throug h Step 6 6 . Refl ection T racki ng (R everse ) Calib rati on Coeff ic[...]

4-41 Performance T ests 10. Sy stem T rac e Noise (Only for Ana lyzers withou t Option 006) 2 Press PRESET , MEN U , POWER , 5 , x1 . 3 Press RETURN , CW FREQ , 3 , G/ n , NUMBER of POINTS , 1601 , x1 . 4 Press MARKER FCTN , MARKER MODE MENU , ST A TS ON to activate th e instrume nt ’ s statistic fea ture. System T race Noise fo r A/R Magnitude 5[...]

4-42 Performanc e Tests 11. System Tra ce Noise (On ly for Analyze rs with Optio n 006) In Cas e of Difficulty 1 Perform the “ ADC Offset Correction Constants ” pr oced ure, locat ed in the “ Adjus tments a nd Correc tion Co nsta nts ” chapter of th e Agilent 8753D Service Guid e . 2 Repe at this per formance te st. 3 Suspec t the A10 Di gi[...]

4-43 Performance T ests 11. Sy stem T race Nois e (Only for Analyz ers with Opt ion 006) 3 Press MARKER FCTN , MARKER MODE MENU , ST A TS ON to activate th e instrume nt ’ s statistic fea ture. System T race Noise for A /R Magnitude from 30 kHz to 3 GHz 4 Press MEAS , T rans: E/E S12 REV . 5 Press MENU , CW FREQ , 3 , G/n , TRI GGER MENU , NUMB E[...]

4-44 Performanc e Tests 12. Test Port In put Imp edanc e disp lay, on the “ Perfo rmance Te st Record . ” System T race Noise for B/R Magnitu de from 3 GHz to 6 GHz 21 Press MENU , CW FREQ , 6 , G/n , TRI GGER MENU , NUMB ER of GR OUPS , 5 , x1 . 22 When t he anal yzer finishes the number of sw eeps, press SCAL E REF , AUTO SC ALE . 23 Write th[...]

4-45 Performance T ests 12. T est Por t Input I mpeda nce Requi red Equipment For 50 Ω Analyzers Cable, APC- 7, 2 4-inch . . . . . . . . . . . . . . . . . . . . . . . . . Agile nt P/N 8 120-477 9 Calibrati on Kit, 7 mm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Agile nt 85031B For 75 Ω Analyzers Cable, 75 Ω , Ty pe-N, 24-[...]

4-46 Performanc e Tests 12. Test Port In put Imp edanc e 8 When the analy zer disp lays the prom pt, CONNECT STD THEN PRESS KEY TO MEASURE , connect a short to r eference test po rt 1. 9 Press F ORWARD: SHORT . 10 At the prom pt, connect a load to refere nce test por t 1. 11 Press F ORWARD: LOAD . 12 When th e analyzer di splays, ’ DONE ’ IF FI[...]

4-47 Performance T ests 12. T est Por t Input I mpeda nce Figure 4-28. S22 1-Port Cal Test S etup 18 Press CAL , CALI BRA TE ME NU , S22 1-PORT . 19 At t he prom pt, connect an open t o ref eren ce te st po rt 2, as sho wn in Figure 4-28 . 20 Press REVERSE: OPEN . 21 When the analy zer disp lays the prom pt, CONNECT STD THEN PRESS KEY TO MEASURE , [...]

4-48 Performanc e Tests 13. Test Port Re ceiver Magnit ude Dyn amic Acc uracy Figure 4-29. Test Port 1 In put Impedance Test Setu p 28 Press MARKER to activate the analyzer ’ s marker 1. Use the fro nt panel knob to locat e the maximum value o f the data trace for eac h of the fr equency rang es liste d in the “ Performance Test Record. ” 29 [...]

4-49 Performance T ests 13. T est Po rt Receiver Ma gnitude Dynamic A ccuracy Figure 4-30. Receiver Ma gnitude Dynamic Accur acy Requi red Equipment Measur ing Recei ver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Agilen t 8902A Step Atte nuator, 110 dB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A gilen t 84[...]

4-50 Performanc e Tests 13. Test Port Re ceiver Magnit ude Dyn amic Acc uracy Figure 4-31. Test Port 2 Dyn amic Accura cy Test Setup[...]

4-51 Performance T ests 13. T est Po rt Receiver Ma gnitude Dynamic A ccuracy 5 On t he Agi lent 8 702D: a Press MEAS , INPUT PO RTS , B , MENU , POW ER , – 4 , x1 . b Using t he analyz er fro nt panel knob, adjust th e test por t pow er fo r a readi ng of – 20.000 dBm on the Agilen t 8902A. c Wait f or the r eading t o stabil ize. 6 On the Agi[...]

4-52 Performanc e Tests 13. Test Port Re ceiver Magnit ude Dyn amic Acc uracy T est Port 1 Magnitud e Dynamic Accuracy 15 Set the Agil ent 8496A to 10 dB. 16 On t he Agil ent 8 702D, pr ess CONTIN UOUS , MEAS , INPUT PORTS , TESTPORT 2 , A . 17 Connec t t he equ ipm ent as show n in Figure 4-32 . NOTE When the Agilent 8902A displays t he “ RECAL [...]

4-53 Performance T ests 13. T est Po rt Receiver Ma gnitude Dynamic A ccuracy Figure 4-32. Test Port 1 Mag nitude Dynamic Acc uracy Test Setup 18 On t he Agi lent 8 702D: a Press MENU , PO WER . b Using t he analyz er fro nt panel knob, adjust th e test por t pow er fo r a readi ng of 0.000 dB on the Agil ent 8902A. c Wait f or the r eading t o sta[...]

4-54 Performanc e Tests 13. Test Port Re ceiver Magnit ude Dyn amic Acc uracy 19 On the Agi lent 8902A , press the blue shift ke y and SET REF . 20 On t he Agi lent 8 702D: a Press CAL , CALI BRA TE ME NU , RESPONSE , THRU . b After the analyzer fi nishes the measur ement, pres s DONE: RESPO NSE . c Press SAVE/R ECALL , SA VE ST A TE . 21 Set the A[...]

4-55 Performance T ests 14. T e st Port R eceiv er Phas e Dynami c Accur acy In Cas e of Difficulty 1 If t he an alyz er fa ils the te st at all power l evels, b e sure you foll owed the recomme nded atte nuator settin gs as liste d in the “ Perf ormanc e Test Record . ” Repe at this per formance te st. 2 If both test port mea sured v alue s ar[...]

4-56 Performanc e Tests 14. Tes t Port Re ceiv er Phas e Dyna mic Ac curacy Figure 4-33. Dynamic Accurac y (Phase) Procedure T est Port 2 Phase D ynamic Accuracy 1 Refer to the “ Test Port Receiver Magnitude Dynamic Accuracy ” portio n of the “ Perform ance Test Re cord, ” for the values in the “ Calc ulated Va lue ” co lu mn. 2 Copy th[...]

4-57 Performance T ests 15. T est P ort Receiv er Ma gnitude Compress ion 7 For eve ry test port input pow er l evel, calculate the receiver phase dyna mic accuracy using the fol lowing formula : Phase Dynamic Ac curacy = SIN – 1 (B) 8 Writ e the valu e in the “ Result s Value ” colu mn of the “ Perf o rmance Test Record. ” T est Port 1 P[...]

4-58 Performanc e Tests 15. Test Port Re ceiv er Magnit ude Comp ress ion 2 Press PRESET , MEA S , T rans: E/E S21 F WD . 3 Press AV G , IF BW , 10 , x1 . 4 Press MENU , CW FREQ , 50 , M/ µ . 5 Press SWEEP TYPE MENU , POWER SWEEP , ST ART , – 10 , x1 . 6 Press MENU , TRI GGER MENU , SINGLE . 7 At th e end of the sw eep, press SC ALE REF , AUTO S[...]

4-59 Performance T ests 16. T est Port Re ceiver Phas e Compre ssion SEARC H: M IN . 25 Write the a bsolu te value o f th e marker 2 reading in the “ Mea sured Valu e ” column of th e “ Pe rformance Test Record. ” 26 Repeat St ep 19 thro ugh Step 25 for the o ther CW freq uencies listed f or P ort 1 in t he “ Perf orman ce Test Record. ?[...]

4-60 Performanc e Tests 16. Tes t Port Re ceiv er Phas e Compre ssion For 75 Ω Analyzers Cable, 75 Ω , Type -N, 24-inch . . . . . . . . . . . . . . . . . . . . . Agile nt P/N 8120- 2408 Procedure T est Port 2 Phase C ompression 1 Connec t t he equ ipm ent as show n in Figure 4-35 . Figure 4-35. Test Port Phase Compression Te st Setup 2 Press PR[...]

4-61 Performance T ests 16. T est Port Re ceiver Phas e Compre ssion T est Port 1 Phase Compress ion 13 Press MEAS , T rans: E/E S12 REV , FORM A T , PHASE . 14 Press MENU , CW FREQ , 50 , M/ µ . 15 Press MENU , TRI GGER MENU , SINGLE . 16 At th e end of the sw eep, p ress SCALE R EF , AUTO SC ALE . 17 Press MARKER , ∆ MODE MENU , ∆ REF= 1 , M[...]

4-62 Performanc e Tests 17. Te s t Port O utput/Input Harmon ics (Option 002 Analyzers with out Option 00 6 Only) 17. Test Port Output/Input Harmonics (Option 002 Analyzers without Option 006 O nly) Perform th is test to dete rmine th e spectral purity of the Agilen t 8702D input and output tes t ports. Requi red Equipment For 50 Ω Analyzers Cabl[...]

4-63 Performance T ests 17. T est Port Outpu t/Input Harmonics ( Option 0 02 Analyzer s witho ut Optio n 006 Only) Figure 4-36. Test Port Outpu t Harmonics T est Setup 5 Press MEAS , T rans: E/E S12 REV , INPUT PORTS , A . 6 After one swee p, pr ess DISP LA Y , DA T A → MEMORY , DA T A/MEM to normal ize the trace. 7 Press SYSTEM , HARMON IC M EAS[...]

4-64 Performanc e Tests 17. Te s t Port O utput/Input Harmon ics (Option 002 Analyzers with out Option 00 6 Only) 15 Press SYSTEM , HARMON IC M EAS , HA RMONIC TH IRD . 16 After one sweep, pres s SC ALE R EF , AUTO SCAL E . 17 Press MARKER FCTN , MARKER MODE MENU , MKR SE ARCH , SEARCH MAX . 18 Write the marker 1 value o n the “ Performa nce Test[...]

4-65 Performance T ests 17. T est Port Outpu t/Input Harmonics ( Option 0 02 Analyzer s witho ut Optio n 006 Only) chann el A ) 2n d har monic . Port 1 Input W orst Case 3rd Harmonic 29 Press STOP , 1 , G/n to change the stop frequ ency for measuring the receiver 3rd harmoni c. 30 Press SYSTEM , HARMON IC M EAS , HARMONI C OFF . 31 After one swee p[...]

4-66 Performanc e Tests 18. Te s t Port O utput/Input Harmon ics (Option 002 Analyzers with Option 006 Only ) 47 After one sweep, pres s DIS PLA Y , DA T A → MEMORY , DA T A/ MEM to no rmalize the trace. 48 Press SC ALE R EF , AUTO SC ALE , SCALE/DIV , 1 , x1 t o get a be tter viewin g of the trace . 49 Press SYSTEM , HARMON IC M EAS , HA RMONIC [...]

4-67 Performance T ests 18. T e st Port Output/In put Harmonics (Option 002 Ana lyzers with Option 006 Only) Figure 4-38. Test Port Outpu t Harmonics T est Setup 5 Press MEAS , T rans: E/E S12 REV , INPUT PO RTS , A . 6 After one swee p, pr ess DISP LA Y , DA T A → MEMORY , DA T A/MEM to normal ize the trace. 7 Press SYSTEM , HARMON IC M EAS , HA[...]

4-68 Performanc e Tests 18. Te s t Port O utput/Input Harmon ics (Option 002 Analyzers with Option 006 Only ) 14 Press SC ALE R EF , AUTO SC ALE , SCALE/DIV , 1 , x1 t o get a be tter viewin g of the trace . 15 Press SYSTEM , HARMON IC M EAS , HA RMONIC TH IRD . 16 After one sweep, pres s SC ALE R EF , AUTO SCAL E . 17 Press MARKER FCTN , MARKER MO[...]

4-69 Performance T ests 18. T e st Port Output/In put Harmonics (Option 002 Ana lyzers with Option 006 Only) 27 Press MARKER FCTN , MARKER MODE MENU , MKR SE ARCH , SEARCH: MAX . 28 Write the mar ker 1 value (which app ears on the an alyzer dis play) on the “ Perform ance Test Re cord. ” This i s the worst ca se por t 1 input (recei ver chann e[...]

4-70 Performanc e Tests 18. Te s t Port O utput/Input Harmon ics (Option 002 Analyzers with Option 006 Only ) harmoni c. 46 Press SYSTEM , HARMON IC M EAS , HARMONI C OFF . 47 After one sweep, pres s DIS PLA Y , DA T A → MEMORY , DA T A/ MEM to no rmalize the trace. 48 Press SC ALE R EF , AUTO SC ALE , SCALE/DIV , 1 , x1 t o get a be tter viewin [...]

4-71 Performance T ests Perfor manc e T est Reco rds Performance Test Records The follow ing tables are to re cord t he pe rform ance test recor ds fo r each of the tests. T est 1. T est Port Output Freq uency Range and Accura cy Test F requen cies (MHz) Min. (MHz) Resu lts M easur ed (MHz) Max. (MHz) Measur ement Uncer tainty (MHz ) 0.03 0.029 999[...]

4-72 Performanc e Tests Perf ormance Test Rec ords T est 2. Exter nal Source Mode Freq uency Range Test F requen cie s (GHz ) Results 0.010 _______ _______ ______ 0.020 _______ _______ ______ 0.100 _______ _______ ______ 1.000 _______ _______ ______ 2.000 _______ _______ ______ 3.000 _______ _______ ______ Option 006 4.000 _______ _______ ______ 5.[...]

4-73 Performance T ests Perfor manc e T est Reco rds T est 3. T est Port Output Po wer Accuracy Test F requen cy Test Po rt Output Power (d Bm) Specif ication (dB) Measur ed Val ue (dB) Measur ement Uncer tainty (dB) 300 kHz 0 ± 1 ________ _______ _____ ± 0. 15 20 MH z 0 ± 1 _____ __________ _____ ± 0.10 50 MH z 0 ± 1 _____ __________ _____ ±[...]

4-74 Performanc e Tests Perf ormance Test Rec ords T est 4. T est Port Output Po wer Range and Linear i ty (1 of 2) Test Settin gs Resu lts Meas ure d (dB) Power Leve l Linear ity (dB) Specific ation (dB) Measu rement Uncer tainty (dB) CW Frequency = 300 kHz – 15 ______________ ____ ___ _______ ________ ± 0.2 ± 0.15 – 13 ______________ ____ _[...]

4-75 Performance T ests Perfor manc e T est Reco rds – 1 __________ _______ _ ______ ___________ _ ± 0.2 ± 0.15 + 1 __________ _______ _ ______ ___________ _ ± 0.2 ± 0.15 + 3 __________ _______ _ ______ ___________ _ ± 0.2 ± 0.15 + 5 __________ _______ _ ______ ___________ _ ± 0.5 ± 0.15 + 7 __________ _______ _ ______ ___________ _ ± 0.[...]

4-76 Performanc e Tests Perf ormance Test Rec ords T est 5. Minimum R Channel Level CW Freq uency Specific ation (dB) Test Po rt Power M easure ment Unc erta inty (dB) 300 kHz < – 35 _______ _______ ______ ± 1.0 3.29 MHz < – 35 __________ _______ ___ ± 1.0 3.31 MHz < – 35 __________ _______ ___ ± 1.0 15.90 MH z < – 35 _______[...]

4-77 Performance T ests Perfor manc e T est Reco rds T est 6. T est Port Input Noise Floor Level Freque ncy Rang e Test Po rt IF Bandwi dth Specifi cation (dBm) Calcu lated Value Measur ement Uncer tainty 50 kHz – 3 GHz Po rt 1 3 kHz – 82 _______ _____ N/A 50 kHz – 3 G Hz Por t 1 10 Hz – 102 _______ _____ N/A 50 kHz – 3 G Hz Por t 2 10 Hz[...]

4-78 Performanc e Tests Perf ormance Test Rec ords T est 8. T est Port Crosstalk Test Settin gs Specif ication (dB) Measu red Value (dB) Measur ement Uncer tainty Crosstalk to Test Port 2 300 kHz – 3 GHz < – 100 _______ _______ ______ N/A Crosstalk to Test Port 2 300 kHz – 3 GHz < – 100 _______ _______ ______ N/A Option 006 Crosstalk [...]

4-79 Performance T ests Perfor manc e T est Reco rds T est 9. Calibra tion Coefficients (1 of 2) Test De scriptio n Freque ncy Rang e Specifica tion (dB) Me asured Valu e (dB) Measur ement Uncer tainty (dB) Forward Directi on Directiv ity 300 kHz – 1. 3 GHz ≥ 35 __________ _______ ___ ± 0.9 Directiv ity 1.3 GHz – 3 GHz ≥ 30 ___ _______ ___[...]

4-80 Performanc e Tests Perf ormance Test Rec ords Trans. Trac king 300 kHz – 1.3 G Hz ± 1.5 __________ _______ ___ ± 0.006 Trans. Trac king 1.3 GHz – 3 GHz ± 1.5 ___ ___________ ______ ± 0. 009 Trans. Trac king Option 006) 3 GHz – 6 GHz ± 2.5 __________ _______ ___ ± 0.021 Forward Directi on Load Match 300 kHz – 1.3 GHz ≥ 18 ___ __[...]

4-81 Performance T ests Perfor manc e T est Reco rds T est 10. Sy stem T race Noise (Only for Analyzers without Option 006) CW Freq uency (GHz) Ratio Measured V alue Specif ication Measurement Uncer tainty 3A / R ________ _______ _____ < 0.006 dB rms N/A 3A / R ________ _______ _____ < 0.038 ° rms N/A 3B / R ________ _______ _____ < 0.006[...]

4-82 Performanc e Tests Perf ormance Test Rec ords T est 12. T est Port In put Impeda nce Test De scriptio n Test P ort Return Lo s s (dB) Specificati on (dB) Measu rement Uncertain ty (dB) 300 kHz – 1.3 GHz Port 2 __________ _______ ___ ≥ 18 ± 1.5 1.3 GHz – 3 GHz Port 2 ___ _______ __________ ≥ 16 ± 1.5 3 GHz – 6 GHz (Optio n 006) Port[...]

4-83 Performance T ests Perfor manc e T est Reco rds T est 13. T est Port Receiv er Mag nitude Dynamic Accuracy Test P ort Input Power 8496A Setting (dB) Test P ort (dB) 8902A (dB) Calcul ated Value (dB ) Spec. (dB) Mea. Uncer. (dB ) Test Po rt 2 – 10 0 _________ ___ ______ ___ ______ ≤ 0.059 ± 0.01 – 20 10 _________ ___ ______ ______ ___ ?[...]

4-84 Performanc e Tests Perf ormance Test Rec ords T est 14. T est Po rt Rec eiver Phase D ynamic Accura cy Test P ort Input Power Calcul ated Value (dB ) A B Resu lts Valu e (degr ees) Spec. (degr ees) Mea. Uncer. Test Port 2 – 10 _________ _________ ___ ______ ______ ___ ≤ 0.42 N/A – 20 _________ _________ ___ ______ ______ ___ ≤ 0.35 N/A[...]

4-85 Performance T ests Perfor manc e T est Reco rds T est 15. T est Port Receiver Magnitude Compression CW Freq uency Test Port Measu red V a lue (dB) Specific ation (d B) M easure ment Unce rtai nty 50 MHz P ort 2 ___ _______ __________ ≤ 0. 45 N/A 1 GHz Port 2 ______ _______ _______ ≤ 0.45 N/A 2 GHz Port 2 ______ _______ _______ ≤ 0.45 N/A[...]

4-86 Performanc e Tests Perf ormance Test Rec ords T est 16. T est Port Receiver Phase Co m pression CW Freq uency Test Port Measu red V alue (degr ees) Specific ation (deg rees) Measu rement Uncertain ty 50 MHz P ort 2 ___ _______ __________ ≤ 6 ° N/A 1 GHz Port 2 ______ _______ _______ ≤ 6 ° N/A 2 GHz Port 2 ______ _______ _______ ≤ 6 ° [...]

4-87 Performance T ests Perfor manc e T est Reco rds T est 17. T est Port Output/Input Harmonics (Option 002 Analyzers without Option 006 Only) Test De scriptio n Speci fication (dBc) Measur ement Va lue (dBc) Measu rement Uncertain ty (dB) Test Port Out put Harmoni cs 2nd ≤ 25 ______ ______ ________ ± 1. 0 3rd ≤ 25 ______ ______ _______ _ ± [...]

4-88 Performanc e Tests Perf ormance Test Rec ords T est 18. T est Port Output/Input Harmonics (Option 002 Analyzers with Option 006 Only) Test De scriptio n Speci fication (d Bc) Measur ement Va lue (dBc) Measu rement Uncertain ty (dB) Test Port Out put Harmoni cs 2nd ≤ 25 ______ ______ ________ ± 3. 0 3rd ≤ 25 ______ ______ _______ _ ± 3.0 [...]

5 Agilent 8702D O ption 01 1 and Agilent 85046A/ 47A Syste m Ver ification 5-4 Step 1. I nitial iza tion 5-4 Step 2 . Measu rement Calibra tion 5-6 Step 3. Device Ve rification 5-8 In Case of Difficul ty 5-11 Agilent 870 2D Option 01 1 and Agile nt 85044A Syst em Verifi cation 5-13 Step 1. I nitial iza tion 5-1 3 Step 2 . Measu rement Calibra tion [...]

5-2 Automated V erification – Option 011 Automate d Performan ce Verifica tion for Option 011 Automated Performance Verification for Option 011 The auto mated per formance verification pr ocedures in this chapte r provid e a high level of c onfiden ce that t he Agilent 8702D Optio n 01 1 is wo rking prop - erly . Performan ce ver ification p r oc[...]

5-3 Automated V e rification – Option 011 Automate d Performanc e V erification for Option 0 11 How to select the s y stem veri fication procedure Check to see how th e verif ication kit fl oppy disk is la bele d: • If th e disk is la beled V e rification Data Di sk , pro ceed with the Agilen t 8702D Option 011 Autom ated M ode S ystem V erific[...]

5-4 Automated V erification – Option 011 Agilent 8702D Option 011 a nd Agilent 85046A/47A System Verification Agilent 8702D Option 01 1 and Agilent 85046A/ 47A Syst em Ve rific ation In o rder to run th is pro cedur e, t he fo llowing e quipment is r equi red: S-Parame ter test s et (for anal yzers without O ptio n 006) . . . . Agilent 85046A S-P[...]

5-5 Automated V e rification – Option 011 Step 1. Initializatio n Figure 5-1. System Verification Test Setup 2 While the eq uipment is w a rmi ng up, r eview the conn ector care infor mation in the Agilent 870 2D User ’ s Gui de . 3 Insert the verificat ion kit disk into the anal yzer ’ s disk dr ive. 4 Press PRESET , SAVE/RECAL L , SELECT DI[...]

5-6 Automated V erification – Option 011 Step 2. Me asurement Calibration Step 2. Measurem ent Cali bration 1 Press CAL , CAL KIT & ST DS , SEL ECT CAL KIT , CAL KIT :7mm , RETURN , RETURN , CALIBRA TE MENU , FULL 2 -PORT . 2 Press ISOLA TION , O MIT ISOLA TION , ISOLA TION DONE . 3 Press REFL ECTION . 4 Con nec t the “ open ” end o f th [...]

5-7 Automated V e rification – Option 011 Step 2. Meas urement Cali bration 7 Press F ORWARD:SHORT . 8 When the ana lyzer displays the message CONNECT STD THEN PRESS KEY TO MEASURE , conn ect t he 50 o hm terminat ion (su pplie d in t he calibrat ion kit) to r eference test port 1, as sh own in Figur e 5-2 . 9 Press F ORWARD:LOAD . 10 When the an[...]

5-8 Automated V erification – Option 011 Step 3 . Device Ve rificat ion 18 Press TR ANSM ISSION , F WD TRANS THRU . 19 When the analy zer fi nish es t he me asure ment, pres s FWD MA TCH THRU . 20 When the analy zer fi nish es t he me asure ment, pres s REV TRANS TH RU . 21 When the analy zer fi nish es t he me asure ment, pres s REV MA TCH THRU [...]

5-9 Automated V e rification – Option 011 Step 3. De vice V erification 3 Press CONTINUE to run the test : • If you switche d the recor d function off , you have to pres s CONTI NUE after each S -paramete r meas ureme nt. • If you switche d the record function on , the test disp lays an d prin ts the pass/ fail informatio n for the S -para me[...]

5-10 Automated V erification – Option 011 Step 3 . Device Ve rificat ion 6 When all measurements are complete, replace the attenuator with the verification mismat ch, as shown in Figure 5-6 . Figure 5-6. Mismatch Devic e Verificati on Setup 7 Press RETURN , TESTS , 30 , x1 , EXECUTE TEST , CONTINUE .[...]

5-11 Automated V e rification – Option 011 In Case of Difficulty 8 When the analyzer f inishe s all the measuremen ts, reconnect the mismat ch verification device, as shown i n Figure 5- 7 . Figure 5-7. Mism atch Device Verific ation Setup 9 Press RETURN , TESTS , 31 , x1 , EXECUTE TEST , CONTINUE . 10 You hav e comp leted th e system v erificati[...]

5-12 Automated V erification – Option 011 In Case of Difficulty 3 If the analyzer sti ll fa ils the test, check the measureme nt calibra tion as follows: a Press PRESET . b Recal l the cali bration by pr essing SA VE/RECAL L , SEL ECT DI SK , INTERNAL MEMO- RY , RETURN . c Use th e front panel kno b to highl ight t he calib ratio n you want to re[...]

5-13 Automated V e rification – Option 011 Agilent 87 02D Opt ion 011 and Ag ilent 8504 4A Sy stem V eri fication Agilent 8702D Option 01 1 and Agilent 85044A System Verification In o rder to run th is pro cedur e, the fo llowing e quipment is require d: Transmi ssion/r efle ction test set . . . . . . . . . . . . . . . . . . . . . . . . A gilent [...]

5-14 Automated V erification – Option 011 Step 2. Me asurement Calibration Figure 5-8. System Verification Test Setup 2 While the eq uipment is w a rmi ng up, r eview the conn ector care infor mation in the Agilent 870 2D User ’ s Gui de . 3 Insert the verificat ion kit disk into the anal yzer ’ s disk drive. 4 Press PRESET , SAVE/REC ALL , S[...]

5-15 Automated V e rification – Option 011 Step 2. Meas urement Cali bration MENU , ONE-P A TH 2-PO RT . 2 Press ISOLA TION , O MIT ISOLA TION , ISOLA TION DONE . 3 Press REFL ECTION . 4 Con nec t the “ open ” end o f th e open/ s hort combi nation (supplied i n the calibrat ion kit) to reference test port 1, as shown in Figure 5-9 . Figure 5[...]

5-16 Automated V erification – Option 011 Step 3 . Device Ve rificat ion 10 When t he analyze r finishes meas uring the stan dard, press ST ANDA RDS DONE . 11 Con nect th e test port c ables as sho wn Figure 5-10 . Figure 5-10. Transmission Cali bration Setup 12 Press TR ANSM ISSION , F WD TRANS THRU . 13 When the analy zer fi nish es t he me asu[...]

5-17 Automated V e rification – Option 011 Step 3. De vice V erification as s hown in F igure 5- 11 . Figure 5-11. Connections fo r the 20 dB Att enuator 3 Press CONTINUE to run the test : • If you switche d the recor d function off , you have to pres s CONTI NUE after each S -paramete r meas ureme nt. • If you switche d the record function o[...]

5-18 Automated V erification – Option 011 Step 3 . Device Ve rificat ion 4 When th e analyzer fi nishes all t he measurements, connect the 5 0 dB atten u ator (supplie d in t he veri fication kit), as shown in Figure 5-12 . Figure 5-12. Connections fo r the 50 dB Att enuator 5 Press RETURN , TESTS , 29 , x1 , EXECUTE TEST , CONTIN UE .[...]

5-19 Automated V e rification – Option 011 Step 3. De vice V erification 6 When all measurements are complete, replace the attenuator with the verification mismat ch, as shown in Figur e 5-13 . Figure 5-13. Mismatch Device Verification Setup 7 Press RETURN , TESTS , 30, x1 , EXECUTE TEST , CONTINU E .[...]

5-20 Automated V erification – Option 011 In Case of Difficulty 8 When th e analyzer finishes al l the me asurements, r econnect the mis match verification device, as shown i n Figure 5- 14 . Figure 5-14. Mism atch Device Verific ation Setup 9 Press RETURN , TESTS , 31 , x1 , EXECUTE TEST , CONTINUE . 10 You hav e comp leted th e system v erifica[...]

5-21 Automated V e rification – Option 011 In Case of Difficulty c Press RECALL ST A TE . d Repeat “ Step 3. De vice Veri fication ” on page 5-16 . 3 If the analyze r still fails the test, ch eck the measuremen t calibration as fo llows: a Press PRESET . b Recall t he calibratio n by press ing SA VE/RECALL , SELECT DI SK , INTERNAL DISK , RE-[...]

[...]

6 1. Source Frequency Range and A ccuracy 6-3 2. Source Power Range, Linearity, and Accuracy 6-5 3. Receiver Minimum R Channel Level 6-9 4. Receiver Mi nimum R Chann el Level for E xternal Source Mode 6-12 5. Recei ver Channe l Noise Floor Level (Only for Analy zers withou t Opt ion 006) 6-14 6. Recei ver Channe l Noise Floor Level (Only for Analy [...]

6-2 Performanc e Tests – Opt ion 0 11 Manua l Perform ance Tests - O ption 011 Manual Performance Tests - Option 011 This chapter c ontain s procedur es which te st the elec tric al performa nce of the Agilent 870 2D Option 01 1. If you are no t using an A gilen t 8702D Option 0 11, refer to Chapt er 4, “ Performance T ests ” . Bef ore starti[...]

6-3 Performance T ests – Option 011 1. Sour ce Fre quenc y Range an d Accu racy WAR NI N G Any servi cing, adjustme nt, maintena nce, or re p air of this p r oduct must be per forme d only by qualified p ersonn el. Repai r infor mation provided in the In Cas e of Difficulty sectio ns o f this chap ter are provided for quali fied servi ce perso nn[...]

6-4 Performanc e Tests – Opt ion 0 11 1. Sour ce Fre que ncy Rang e and Accurac y Figure 6-1. Source Fre quency Rang e and Accuracy Test Setup 2 Press PRESET , MEN U , CW F REQ . 3 Press 300 , k/m and write the frequency counter reading on the "Performan ce Test R ecor d." 4 Repeat Step 3 for each inst rument fr equency li sted in t he [...]

6-5 Performance T ests – Option 011 2. Sour ce Powe r Range , Linear ity, and Accu racy 2. Source Power Range, Linear ity, and Ac curacy Perfo rm this test to ver ify the analyze r ’ s powe r rang e and line arity at d ifferen t CW freq uencies t hroug hout the analyz er ope rating freque ncy rang e. Requi red Equipment Power Mete r . . . . . .[...]

6-6 Performanc e Tests – Opt ion 0 11 2. Sou rce P ower Rang e, L inear ity, and Accur acy 2 Zero and cal ibrate th e power m eter. Also , set th e power meter fo r dBm. Refer to the power me ter operat ing and servi ce manual for m ore inform ation on how to do this ta sk. 3 Press PRESET , MEN U , POWER , 10 , x1 . 4 Press MENU , CW FREQ , 300 ,[...]

6-7 Performance T ests – Option 011 2. Sour ce Powe r Range , Linear ity, and Accu racy 9 Write the power meter re ading in th e "Second Value" colu mn on the "Performance Test Record." 10 Calculat e the path loss throug h the power sp litter with this formula: First V alue – Second V al ue = Path Loss 11 Write the r esult o[...]

6-8 Performanc e Tests – Opt ion 0 11 2. Sou rce P ower Rang e, L inear ity, and Accur acy front pan el. 16 Press PO WER , – 5 , x1 . W rite t he po wer met er rea ding in th e “ Me asur ed Value ” column on th e “ Pe rformance Test Record ” . 17 On t he “ Perf orman ce Test Record ” , copy the “ Path Loss ” val ue, pr eviously [...]

6-9 Performance T ests – Option 011 3. Rece iver Minimum R Channel Le vel 31 Press MENU , CW FREQ , 300 , k/m . Se t the power c alibra tion fact or for t his CW frequency . 32 On t he “ Perfor mance Test Record ” , c opy the “ Path Loss ” v alue , previousl y calcu late d for th is CW f requency, into the “ Pass Loss ” c olumn. 33 Ca[...]

6-10 Performanc e Tests – Opt ion 0 11 3. Rece iver Minimum R Channel Le vel Requi red Equipment Adapter, APC-3.5 (m) to APC-7 . . . . . . . . . . . . . . . . . . Agi lent P/N 1250- 1746 Cable, APC-7 24- inch . . . . . . . . . . . . . . . . . . . . . . . . . . . Ag ilent P/N 8120-477 9 Atten uator , 20 dB . . . . . . . . . . . . . . . . . . . . .[...]

6-11 Performance T ests – Option 011 3. Rece iver Minimum R Channel Le vel c If the a nalyzer still doesn ’ t phase lock, contin ue increasing the sou rce output power un til phas e lock is ac hieved. d Write the mar ker value in th e “ Perfo rmanc e Test Reco rd ” . • Repeat Step 4 throu gh Step 6 fo r the other CW fre quenc ies lis ted [...]

6-12 Performanc e Tests – Opt ion 0 11 4. Re ceiver Mini mum R Channel Le vel for Ex ternal Sour ce Mod e 5 Refe r to the Agilent 8753 D Option 0 11 Service G uide for m ore troublesh ooting informat ion. 4. Re ceiver Mi nimu m R Channe l Level for Exte rnal Source Mode Perfo r m t his te st to ve rify prop er ph ase lock i n the external source [...]

6-13 Performance T ests – Option 011 4. Rece iver Minimu m R Channe l Level f or Exte rnal Source Mode 2 On the ext erna l source, press PRESET , POWER LEVEL , 4 , dB(m) , CW , 10 , MHz . 3 On the an alyzer, press PRESET , MENU , CW FREQ , 10 , M/ µ , SY STEM , INSTRUMENT MODE , EXT SOURCE AUTO to set up the an alyzer f or an ex ternal s ource i[...]

6-14 Performanc e Tests – Opt ion 0 11 5. Receive r Chann el Noise Floor Level ( Only for A nalyzer s withou t Option 006) In Cas e of Difficulty WAR NI N G These servicing instructions are for use by quali f ied personnel o nly. To avoi d electr ical s hock, d o not p erform a ny servic ing unl ess you are qualified to d o so. WAR NI N G The ope[...]

6-15 Performance T ests – Option 011 5. Re ceiver Channel Noise Floor Level ( Only for Analy zers without Option 006) Figure 6-7. Receiver Ch annel Noise Floor Level Test Se tup 2 Press PRESET , MEN U , POWER , – 10 , x1 . Receiver Ch annel A Noise Floor Level wi th a 3 kHz IF BW 3 Press MEAS , INPUT PO RTS , A , FORMA T , LIN MAG , SCALE R EF [...]

6-16 Performanc e Tests – Opt ion 0 11 5. Receive r Chann el Noise Floor Level ( Only for A nalyzer s withou t Option 006) 11 Use th e fol lowing equa tion to c onvert the linear magnitude m ean value to lo g magn itude: Power (dBm) = 20 * [log 10 (linear magnitude mean value)] 12 Write this calcul ated value in the “ Perf orma nc e Test Re cor[...]

6-17 Performance T ests – Option 011 6. Rece iver C hannel Noise Floo r Level (Only for A nalyzer s with Opt ion 006) 6. Receiver Channel Noi se Floor Le vel (Only for Analyzers with Option 006) Perfor m this test to determ ine t he an alyze r receiv er chan nel no ise fl oor lev els. Requi red Equipment Attenua tor, 20 dB . . . . . . . . . . . .[...]

6-18 Performanc e Tests – Opt ion 0 11 6. Rece iver Channel Nois e Floor Level (Only for Analyz ers with Option 00 6 ) 5 When the analyze r finishes the sweep , not ice the mean value, wh ich appea rs on the an alyzer displ ay. 6 Use th e fol lowing equa tion to c onvert the linear magnitude m ean value to lo g amplit ude: Power (dBm) = 20 * [log[...]

6-19 Performance T ests – Option 011 6. Rece iver C hannel Noise Floo r Level (Only for A nalyzer s with Opt ion 006) Receiver Ch annel B Noise Floor Leve l with a 3 kHz IF BW (50 kHz – 3 GHz ) 18 Press AV G , IF BW , 3 , k/m t o cha nge th e IF bandw idth to 3 k Hz. 19 Press MENU , TRI GGER MENU , SINGLE . 20 When th e analyzer finishes t he s[...]

6-20 Performanc e Tests – Opt ion 0 11 6. Rece iver Channel Nois e Floor Level (Only for Analyz ers with Option 00 6 ) Receiver Ch annel A Noise Floor Leve l with 10 Hz IF BW (3 GH z – 6 GHz) 33 Press MEAS , INPUT PO RTS , A . 34 Press MENU , TRI GGER MENU , SINGLE . 35 When th e analyzer finishes t he sweep, record the mean value, which appear[...]

6-21 Performance T ests – Option 011 7. Rece iver Magnitude Frequ ency Res pons e 7. Receiver Magnit ude Frequency Response Perfo rm this te st to ve rify how well the analy zer t ransfers i nformati on from the RF to IF , an d how accur ately it processes and displ ays that informati on. Requi red Equipment Power Mete r . . . . . . . . . . . . .[...]

6-22 Performanc e Tests – Opt ion 0 11 7. Rece iver Magnitude Frequ ency Res pons e 3 Press PRESET , MA RKER , MEAS , INPUT PORTS , R , MENU , PO WER , 6 , x1 . 4 Press CW FREQ , 300 , k/m . S et the calibration factor on the po wer meter for t his CW frequency . 5 Write the power met er readin g on the “ Perform ance Test Record. ” 6 Write t[...]

6-23 Performance T ests – Option 011 7. Rece iver Magnitude Frequ ency Res pons e Input B Magnitude Freque ncy Response 13 Connec t t he equ ipm ent as show n in Figure 6-11 . Figure 6-11. Magnitude Freque ncy Response Te st Setup (Recei ver Inpu t B) 14 Press MEAS , INPUT PO RTS , B , MENU to start mea surin g the pow er del ivered to rece iver [...]

6-24 Performanc e Tests – Opt ion 0 11 8. Rece iver Phase Fr equency Res ponse In Cas e of Difficulty 1 Suspect poo r trackin g betwee n the ports of th e power s plitter if al l receiver inpu ts fail. Try to repe at the te st with anot her power sp litter. 2 Suspect source drift if rece iver i nputs A and B fail th is tes t at any freque ncy. Co[...]

6-25 Performance T ests – Option 011 8. Rece iver P hase Freq uenc y Response Figure 6-12. Phase Frequ ency Response Test Setup Phase Frequency Response from 300 kHz to 3 G Hz 2 Press PRESET , MEN U , POWER , 10 , x1 . 3 Only for Analyz ers with Opti on 006: Press STO P , 3 , G/n . 4 Press FORMA T , PHA SE , MARKER FCTN , MARKER M ODE MENU , ST A[...]

6-26 Performanc e Tests – Opt ion 0 11 9. Rece iver Input Crosst alk 12 Press SCALE REF , ELECTRICAL DELA Y . Turn t h e analyze r front panel knob to vary the e lectrical d elay until t he tr ace is in t he mos t lin ear horizont al positio n . 13 Press MENU , TRI GGER MENU , SINGLE . Write the p-p value , which appear s on the analy zer display[...]

6-27 Performance T ests – Option 011 9. Rece iver In put Cross talk Requi red Equipment 2-way Power Sp litter (2), 50 Ω . . . . . . . . . . . . . . . .Agilent 11667A Option 001 Termi nation ( 3), 5 0 Ω . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A gil ent 908A Attenua tor, 20 dB . . . . . . . . . . . . . . . . . . . . [...]

6-28 Performanc e Tests – Opt ion 0 11 9. Rece iver Input Crosst alk (Only for Op tion 006 Analyzers) R i nto A Crosstal k from 3 GHz to 4.5 GHz 9 Press ST ART , 3 , G/n , STOP , 4.5 , G/n , NUMBER of GROUPS , 5 , x1 . 10 When the analyze r finis h es the nu mber of sweeps, write the ma rker value, which appea rs on t he analyzer display, o n the[...]

6-29 Performance T ests – Option 011 9. Rece iver In put Cross talk B into A Crosstalk from 300 kHz to 1 GHz 22 Connec t t he equ ipm ent as show n in Figure 6-14 . Figure 6-14. B into A Rec eiver Input Cro sstalk Test Setup 23 Press ST ART , 300 , k/m , STO P , 1 , G/n. 24 Press MEAS , INPUT PO RTS , A/B , MENU , TRIGGER MENU , NUMBER of GROUPS [...]

6-30 Performanc e Tests – Opt ion 0 11 9. Rece iver Input Crosst alk (Only for Op tion 006 Analyzers) B i nto A Crosstal k from 4.5 GHz to 6 GHz 30 Press ST ART , 4.5 , G/n , STOP , 6 , G/n , TRIGGER MEN U , NUMBER of GROUPS , 5 , x1 . 31 When the analyze r finis h es the nu mber of sweeps, write the ma rker value, which appea rs on t he analyzer[...]

6-31 Performance T ests – Option 011 9. Rece iver In put Cross talk A into B Cro sstalk from 1 GHz to 3 GHz 38 Press ST ART , 1 , G/ n , STOP , 3 , G/n . 39 Press MEAS , INPUT PORTS , A/R , AV G , AVERAGING OF F , MENU , TRIG G ER MENU , SINGLE . 40 At the en d of the sw eep, pr ess DIS PLA Y , DA T A → MEMORY , DA T A/MEM , MEAS , INPU T PORTS[...]

6-32 Performanc e Tests – Opt ion 0 11 9. Rece iver Input Crosst alk In Cas e of Difficulty WAR NI N G These servicing instructions are for use by quali f ied personnel o nly. To avoi d electr ical s hock, d o not p erform a ny servic ing unl ess you are qualified to d o so. WAR NI N G The opening of covers or r emoval of part s is likely to exp [...]

6-33 Performance T ests – Option 011 10. Re ceiver T race N oise 10. Recei ver Trace Noise Perfo r m t his te st to ve rify the r eceiver t race n oise on a CW signal i n ratio mode. Requi red Equipment 3-way Power Splitter , 50 Ω . . . . . . . . . . . . . . . . . . . . . . . . . . . . Agil ent 1185 0C Attenua tor, 10 dB . . . . . . . . . . . .[...]

6-34 Performanc e Tests – Opt ion 0 11 10. Rece iver Trace Noi se statistic fea ture. 5 Write the s.dev (stand ard deviation) valu e, which appears on the analyzer disp lay, o n the "Perfo rmance Test Reco rd." 6 Press ME AS , INPUT PORTS , B/R . Write the s.dev (standard de viation) value on the "Performance Test Record." 7 P[...]

6-35 Performance T ests – Option 011 11. Recei ver I nput Impe dance 11. Recei ver Input Impedance Perfo r m t his te st to ve rify the r eturn los s of each of t he ana lyzer ’ s rece iver input s. Requi red Equipment Test s et, 50 Ω . . . . . . . . . . . . . . . . . . . . . . . . . . A gilen t 85044A/8 5046A/85 047A 2-way Power Splitter , 5[...]

6-36 Performanc e Tests – Opt ion 0 11 11. Rece iver Inpu t Imped ance 2 Press PRESET , MEN U , NUMBER of POINTS , 1601 , x1 . 3 Press CAL , CAL KI T & STD S , SELECT CAL KI T , N 50 Ω , RETURN , R ETU RN , CALIBRA TE MENU , S11 1-PORT . 4 Connect an open to t he test port cable adap ter, by pressing FORWARD: OPENS , OPEN (M) , DONE: OPENS [...]

6-37 Performance T ests – Option 011 11. Recei ver I nput Impe dance Figure 6-18. Receiver A In put Impedanc e Test Se t up 14 Press PRESET , MEA S , INPUT PORTS , B/R , MENU , NUMBER of POI NTS , 1601 , x1 . 15 Press CAL , CALI BRA TE ME NU , S11 1-PORT . Repeat Step 4 through Step 1 2 for the analy zer recei ver in put A retu rn loss.[...]

6-38 Performanc e Tests – Opt ion 0 11 11. Rece iver Inpu t Imped ance 16 Connec t t he equ ipm ent as show n in Figure 6-19 . Figure 6-19. Receiver R Input I mpedance Te st Calibra tion Test Se tup 17 Press PRESET , MEA S , INPUT PORTS , A/B , MENU , NUMBER of POINTS , 1601 , x1 . 18 Press CAL , CALIBRA TE MENU , S11 1-PORT . Repe at Step 4 thro[...]

6-39 Performance T ests – Option 011 12. Re ceiver Ma gnitude Dynami c Accur acy 20 Repeat Step 7 throu gh Step 12 to measure t he receiver R inp u t imp edance . In Cas e of Difficulty WAR NI N G These servicing instructions a re for use by quali f ied personnel o nly. To avoi d electr ical s hock, d o not p erform a ny servic ing unl ess you ar[...]

6-40 Performanc e Tests – Opt ion 0 11 12. Rece iver Magnitud e Dyna mic Acc uracy Figure 6-21. Receiver Ma gnitude Dynamic Accur acy Requi red Equipment Measur ing Recei ver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Agi len t 8902A Step Atte nuator, 110 dB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [...]

6-41 Performance T ests – Option 011 12. Re ceiver Ma gnitude Dynami c Accur acy c Press AV G , IF B W , 10 , x1 . 4 Connec t t he equ ipm ent as show n in Figure 6-22 . Figure 6-22. Channe l A Magnitud e Dynamic Acc uracy Test Se tup 5 On t he Agil ent 8702D Opt ion 0 11: a Press MEAS , INPUT PO RTS , A , MENU , POWER . b Using t he analyz er fr[...]

6-42 Performanc e Tests – Opt ion 0 11 12. Rece iver Magnitud e Dyna mic Acc uracy 6 On the Agi lent 8902A , press the blue shift ke y and SET REF . 7 On t he Agil ent 8702D Opt ion 0 11: a Press CAL , CALI BRA TE ME NU , RESPONSE , THRU . b After the analyzer fi nishes the measur ement, pres s DONE: RESPO NSE . c Press SAVE/R ECALL , SA VE ST A [...]

6-43 Performance T ests – Option 011 12. Re ceiver Ma gnitude Dynami c Accur acy 18 Connec t t he equ ipm ent as show n in Figure 6-23 . Figure 6-23. Channe l B Magnitud e Dynamic Acc uracy Test Se tup 19 On t he Agil ent 8702D Opt ion 0 11: a Press MENU , PO WER . b Using t he analyz er fro nt panel knob, adjust th e test por t pow er fo r a rea[...]

6-44 Performanc e Tests – Opt ion 0 11 12. Rece iver Magnitud e Dyna mic Acc uracy a Press CAL , CALI BRA TE ME NU , RESPONSE , THRU . b After the analyzer fi nishes the measur ement, pres s DONE: RESPO NSE . c Press SAVE/R ECALL , SA VE ST A TE . 22 Set the Agil ent 8496A to 0 dB. 23 On t he Agil ent 8 702D Opt ion 0 11, pre ss MENU , TRIGGER ME[...]

6-45 Performance T ests – Option 011 12. Re ceiver Ma gnitude Dynami c Accur acy Figure 6-24. Channel R M agnitude Dynamic Accurac y Test Setup 31 Set the Agil ent 8496A to 20 dB. 32 On t he Agil ent 8702D Opt ion 0 11: a Press C ONTINUOUS , MEAS , IN PUT PORTS , R , MENU , POW ER . b Using t he analyz er fro nt panel knob, adjust th e test por t[...]

6-46 Performanc e Tests – Opt ion 0 11 12. Rece iver Magnitud e Dyna mic Acc uracy 36 On t he Agil ent 8 702D Opt ion 0 11, pre ss MENU , TRIGGER MENU , SINGL E . 37 Write the me an value i n the "Receiver Ch annel R" column of the "Performan ce Test R ecor d." 38 Write the Agile nt 8902A readou t in the "8902 A" col[...]

6-47 Performance T ests – Option 011 13. Rece iver P hase D ynamic Ac curac y a Perfo rm the "IF Amplifi er Corr ection Const ants " and "ADC O ffset Correct ion Constants" proced ures (located in the "Adju stments and Corr ectio n Con- stants" chapter of the Agi lent 8753D Option 011 Service Gui de ). b Repe at this[...]

6-48 Performanc e Tests – Opt ion 0 11 14. Receiv er Magnitud e Compressio n 4 Write the result in the "A" column of t he "Perfor mance Test Record." 5 For ever y receiver in put pow er level, cal culate "B" us ing the follo wing fo rmula : B = 1 – A 6 Writ e the result in t he " B" co lumn of t he "[...]

6-49 Performance T ests – Option 011 14. Rece iver Magnitude Comp ressio n Addition al Required Equi pment for Analyzers with Op tion 006 Power Senso r . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Agilent 8 481A Procedure Chan nel A Magnitude Compression 1 Zero a nd ca librate th e power mete r. 2 Connec t t he [...]

6-50 Performanc e Tests – Opt ion 0 11 14. Receiv er Magnitud e Compressio n Figure 6-26. Channel A M agnitude Compression T est Setup[...]

6-51 Performance T ests – Option 011 14. Rece iver Magnitude Comp ressio n 3 Press PRESET , AV G , IF BW , 10 , x1 . 4 Press MENU , CW FR EQ , 50 , M/ µ . Set th e calibrat ion facto r on the po wer meter for this CW freque ncy. 5 Press PO WER , – 4 , x1 . Use the analyzer ’ s fr ont pan el k nob t o adjust the s ource powe r for a power met[...]

6-52 Performanc e Tests – Opt ion 0 11 14. Receiv er Magnitud e Compressio n 20 Press STOP and en ter the “ St op Power ” value as determin ed in Step 18 . 21 Press MENU , TRI GGER MENU , SINGLE . 22 At th e end of the sw eep, press SC ALE REF , AUTO SC ALE . 23 Press MARKER , ∆ MODE MENU , ∆ REF=1 , MA RKER FCTN , MARKER MODE MENU , MKR [...]

6-53 Performance T ests – Option 011 14. Rece iver Magnitude Comp ressio n Channel B Magni tude Compression 27 Connec t t he equ ipm ent as show n in Figure 6-27 . Figure 6-27. Channel B Magnitude Compression Test Setup[...]

6-54 Performanc e Tests – Opt ion 0 11 14. Receiv er Magnitud e Compressio n 28 Press MEAS , INPUT PO RTS , B/R . 29 Repeat Step 26 for the CW fr equencie s listed i n the “ Perfo rman ce Te st Record ” . Channel R Magnitud e Compression 30 Connec t t he equ ipm ent as show n in Figure 6-28 .[...]

6-55 Performance T ests – Option 011 14. Rece iver Magnitude Comp ressio n Figure 6-28. Channel R Magn itude Compression Test Setup 31 Repeat Step 26 for the CW fr equencie s listed i n the “ Perfo rman ce Te st Record ” .[...]

6-56 Performanc e Tests – Opt ion 0 11 15. Rece iver Phase Co mpressi on In Cas e of Difficulty WAR NI N G These servicing instructions are for use by quali f ied personnel o nly. To avoi d electr ical s hock, d o not p erform a ny servic ing unl ess you are qualified to d o so. WAR NI N G The opening of covers or r emoval of part s is likely to [...]

6-57 Performance T ests – Option 011 15. Rece iver Ph ase Co mpressi on Procedure Channel A Phase Compressi on 1 Zero a nd ca librate th e power mete r. 2 Connec t t he equ ipm ent as show n in Figure 6-29 . Figure 6-29. Channe l A Phase Compre ssion Test Setup[...]

6-58 Performanc e Tests – Opt ion 0 11 15. Rece iver Phase Co mpressi on 3 Press PRESET , AV G , IF B W , 10 , x1 , FORM A T , PHAS E . 4 Press MENU , CW FREQ , 50 , M / µ . Set the calibrat ion factor on the powe r meter for this CW freque ncy. 5 Press PO WER , – 4 , x1 . 6 Use the analyzer ’ s front panel knob to adjus t the s ource po wer[...]

6-59 Performance T ests – Option 011 15. Rece iver Ph ase Co mpressi on keypad to en ter the “ Sta rt Power ” value as determined in Step 18 . 21 Press STOP and en ter the “ St op Power ” value as determin ed in Step 19 . 22 Press MENU , TRI GGER MENU , SINGLE . 23 At th e end of the sw eep, p ress SCALE R EF , AUTO SC ALE . 24 Press MARK[...]

6-60 Performanc e Tests – Opt ion 0 11 15. Rece iver Phase Co mpressi on Channel B Phase Compressi on 28 Connec t t he equ ipm ent as show n in Figure 6-30 . Figure 6-30. Channe l B Phase Compre ssion Test Setup 29 Press MEAS , INPUT PO RTS , B/R . 30 Repeat Step 27 for t he ot her CW fr eque ncies l iste d in t he “ Performance Test Record. ?[...]

6-61 Performance T ests – Option 011 15. Rece iver Ph ase Co mpressi on Channel R Phase Compressi on 31 Connec t t he equ ipm ent as show n in Figure 6-31 . Figure 6-31. Channel R Phas e Compression T est Setup 32 Repeat Step 27 for t he ot her CW fr eque ncies l iste d in t he “ Performance Test Record. ”[...]

6-62 Performanc e Tests – Opt ion 0 11 16. Sour ce and Receiv er Ha rmon ics (Op tion 00 2 Onl y) In Cas e of Difficulty WAR NI N G These servicing instructions are for use by quali f ied personnel o nly. To avoi d electr ical s hock, d o not p erform a ny servic ing unl ess you are qualified to d o so. WAR NI N G The opening of covers or r emova[...]

6-63 Performance T ests – Option 011 16. Sour ce and Re cei ver Harmo nics (Option 0 02 Only) Figure 6-32. Source Harm onics Test Setup 2 Press PRESET , MEN U , POWER , 20 , x1 . 3 Press ST ART , 16 , M/ µ , STOP , 1.5 , G/n to set the freque ncy range f or search ing the source 2nd har monic. 4 Only for Analyz ers with Opti on 006: Press STO P [...]

6-64 Performanc e Tests – Opt ion 0 11 16. Sour ce and Receiv er Ha rmon ics (Op tion 00 2 Onl y) 13 Press SYSTEM , HARMON IC M EAS , HARMONI C OFF , DISPLA Y . 14 After one sweep, pres s DA T A → ME MO RY , DA T A/MEM to no rmalize the t race and record t he fundam ental. 15 Press SYSTEM , HARMON IC M EAS , HA RMONIC TH IRD to pre pare the ana[...]

6-65 Performance T ests – Option 011 16. Sour ce and Re cei ver Harmo nics (Option 0 02 Only) 24 Move t he receive r A input cabl e to r eceiv er inp ut B. 25 Press SYSTEM , HARMON IC M EAS , HARMONI C OFF , STOP , 1.5 , G/ n . 26 Only for Analyz ers with Opti on 006: Press STO P , 3 , G/n . 27 Repeat Step 6 throu gh Step 9 to measure the s ource[...]

6-66 Performanc e Tests – Opt ion 0 11 17. Rece iver Magnit ude Fre quency Re spons e (Opt ion 00 2 Only) for the r eceiver input A. Press MEA S , INPUT PORTS , A in Step 6 . 36 Repeat Step 11 thr ough Step 1 6 to measure the receiver wor st case 3nd harm o nic for the rece iver input A. In Cas e of Difficulty WAR NI N G These servicing instructi[...]

6-67 Performance T ests – Option 011 17. Recei ver Ma gnitu de Fr equency Res ponse (Opti on 002 Only) Additio nal E quipmen t Requi red for O ption 00 6 Power Senso r . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Agilent 8 481A Procedure Source Harm onic s 1 Connec t t he equ ipm ent as show n in Figure 6-35 . F[...]

6-68 Performanc e Tests – Opt ion 0 11 17. Rece iver Magnit ude Fre quency Re spons e (Opt ion 00 2 Only) Test R ecord. ” 8 Press B . Write the marker 1 rea ding, which app ears o n th e anal yzer displa y, in the “ Input B Val ue ” column o n the “ Performa nce Test Record. ” 9 On the ex terna l source , press 48 , MHz . R ecord the po[...]

6-69 Performance T ests – Option 011 Performa nce T est Reco rds - Opt ion 011 Performance Test Records - Opti on 011 The follow ing tables are to re cord t he pe rform ance test recor ds fo r each of the Agilent 8702D O ption 01 1 tests . T est 1. So urce Frequenc y Range and Accuracy CW Freq uency (MHz) Low er Li mit (MHz) Measur ed Val ue (MHz[...]

6-70 Performanc e Tests – Opt ion 0 11 Perfor mance Test Record s - Option 011 T est 2. Sourc e Power Rang e, Linearity , and Accu racy (Path Loss Ca lculations) CW Freq uency Sou rce O utp ut Power L evel (dBm) First Val ue (dB) Second Val ue (d B) Path Lo ss (dB ) 300 kHz +10 ________ _______ __ _______ ______ _______ _______ _ 20 MH z +10 ____[...]

6-71 Performance T ests – Option 011 Performa nce T est Reco rds - Opt ion 011 + 1 + 9 ___ _____ ________ _ _______ ± 0.25 ± 0.15 + 3 + 7 ___ _____ ________ _ _______ ± 0.25 ± 0.15 + 5 + 5 ___ _____ ________ _ _______ ± 0.25 ± 0.15 + 7 + 3 ___ _____ ________ _ _______ ± 0.25 ± 0.15 + 9 + 1 ___ _____ ________ _ _______ ± 0.25 ± 0.15 + 11[...]

6-72 Performanc e Tests – Opt ion 0 11 Perfor mance Test Record s - Option 011 + 20 – 10 ___ _____ _ _______ _ _______ ± 0.5 ± 0.15 Option 006 CW Fre quency = 3 00 kHz + 13 – 3 _______ _ _ _______ _____ ___ ± 0. 5 ± 0.15 + 18 – 8 _______ _ _ _______ _____ ___ ± 0. 5 ± 0.15 CW Fre quency = 3 GHz + 13 – 3 _______ _ _ _______ _____ ___[...]

6-73 Performance T ests – Option 011 Performa nce T est Reco rds - Opt ion 011 T est 2. So urce Power , Range, Lin earity and Ac curacy (Power Level Ac curac y) CW Freq uency (M Hz) Path Loss (dB) Calib rat ed Power Level (dB ) Measu red Value (d B) Power Level Accurac y (dB) Spec. (dB) Meas. Uncer. (dB) So urce Output Powe r Level = +10 d Bm 0.3[...]

6-74 Performanc e Tests – Opt ion 0 11 Perfor mance Test Record s - Option 011 T est 3. Recei ver Mini mum R Chann el Level CW Freq uency Specific ation (dB) Mark er Val ue (dB) M easur ement U ncerta inty (dB) 300 kHz < – 35 _______ _______ ______ ± 1.0 3.29 MHz < – 35 __________ _______ ___ ± 1.0 3.31 MHz < – 35 __________ ____[...]

6-75 Performance T ests – Option 011 Performa nce T est Reco rds - Opt ion 011 T est 4. Receiver Minim um R Chann el Level for External S ource Mode CW Freq uency (MHz) Frac-N VCO Lower Limit (MHz) Frac-N VCO Upper Limit (M Hz) Measur ed Val ue (MHz) Measur ement Uncer tainty 10 49 .496 50.496 __ ______ ____ N/A 20 37 .620 38.380 __ ______ ____ N[...]

6-76 Performanc e Tests – Opt ion 0 11 Perfor mance Test Record s - Option 011 T est 5. Receiver Cha nnel Noise Floor Level Freque ncy Rang e IF Band width Specifica tion (dBm) Calcu lated Value Measu rement Unce rtai nty Receiv er Chan nel A 300 kHz – 3.0 GHz 3 kHz – 90 ______ ______ N/A 300 kHz – 3.0 GHz 10 Hz – 110 ___ _______ __ N/A R[...]

6-77 Performance T ests – Option 011 Performa nce T est Reco rds - Opt ion 011 T est 7. Receiver Mag nitude Frequency Response CW Freque ncy Power Mete r Read ing R Inpu t Power A Input Power B In put Power Greate st Differ ence Spec. (dB) Meas. Uncer. (dB) Example – 10.0 – 10.14 – 10.09 – 10.10 0.14 ± 1 ± 0.05 300 k Hz ___ ____ _______[...]

6-78 Performanc e Tests – Opt ion 0 11 Perfor mance Test Record s - Option 011 T est 8. Receiver Phase Frequen cy Response Freque ncy Rang e Ratio Specif ication Measur ed Va lue Meas urement Unce rtaint y 300 kHz – 3 GHz A/R ± 3 ° _______ ______ ± 0.35 ° 300 kHz – 3 GHz B/R ± 3 ° ___________ __ ± 0.35 ° 300 kHz – 3 GHz A/B ± 3 ° [...]

6-79 Performance T ests – Option 011 Performa nce T est Reco rds - Opt ion 011 Option 006 R into A Cr ossta lk 3.0 GHz – 4.5 GHz – 82 _______ ____ ____ N/A 4.5 GHz – 6.0 GHz – 75 _______ ____ ____ N/A R into B Cr osstalk 3.0 GHz – 4.5 GHz – 82 _______ ____ ____ N/A 4.5 GHz – 6.0 GHz – 75 _______ ____ ____ N/A B into A Cr ossta lk [...]

6-80 Performanc e Tests – Opt ion 0 11 Perfor mance Test Record s - Option 011 T est 10. Receiver T race Noise CW Freq uency (GHz) Ratio Measured V alue Specif ication (rms) Measur ement Uncer tainty 3A / R ________ _______ _____ ≤ 0 .006 dB N/A 3B / R ________ _______ _____ ≤ 0 .006 dB N/A 3A / B ________ _______ _____ ≤ 0 .006 dB N/A 3A /[...]

6-81 Performance T ests – Option 011 Performa nce T est Reco rds - Opt ion 011 T est 12. Receive r Magnitude Dyn amic Accu racy (1 of 2) Rece iver Input Power (dB) Agilent 8496A Setting (dB) Rece iver Chan nel A (dB) Agilent 8902A (dB) Magn itude Value (dB ) Spec. (dB) Meas . Uncer. (dB ) Channel A – 10 0 _________ ___ ______ ___ ______ ≤ 0.0[...]

6-82 Performanc e Tests – Opt ion 0 11 Perfor mance Test Record s - Option 011 – 90 80 _________ ___ ______ ______ ___ ≤ 0.680 ± 0. 180 – 100 90 ___ ______ ______ ___ ______ ___ ≤ 1.950 ± 0. 200 – 110 100 ______ ___ ______ ___ _________ ≤ 5.200 ± 0.28 0 Channel R – 10 0 _________ ___ ______ ___ ______ ≤ 0.075 ± 0. 010 – 20 1[...]

6-83 Performance T ests – Option 011 Performa nce T est Reco rds - Opt ion 011 – 100 _________ ______ ___ ______ ___ _________ ≤ 16.00 N/A – 110 _________ ______ ___ ______ ___ _________ ≤ 51.50 N/A Channel B – 10 ________ _ _________ ___ ______ ______ ___ ≤ 0.80 N/A – 20 ________ _ _________ ___ ______ ______ ___ ≤ 0.40 N/A – 3[...]

6-84 Performanc e Tests – Opt ion 0 11 Perfor mance Test Record s - Option 011 T est 14. Receiver Magni tude C ompression (1 of 2) CW Freq uency Sta rt Powe r (dBm) Stop Po wer (dBm) Measur ed Value (dB ) Specif ication (dB) Measur ement Uncer tainty Channel A 50 MHz _________ ______ ___ ______ ___ ≤ 0.32 N/A 1 GHz ___ ______ ___ ______ ___ ___[...]

6-85 Performance T ests – Option 011 Performa nce T est Reco rds - Opt ion 011 5 GHz ___ ______ ___ ______ ___ ______ ≤ 0. 32 N/A 6 GHz ___ ______ ___ ______ ___ ______ ≤ 0. 32 N/A Channel R 4 GHz ___ ______ ___ ______ ___ ______ ≤ 0. 32 N/A 5 GHz ___ ______ ___ ______ ___ ______ ≤ 0. 32 N/A 6 GHz ___ ______ ___ ______ ___ ______ ≤ 0. 3[...]

6-86 Performanc e Tests – Opt ion 0 11 Perfor mance Test Record s - Option 011 1 GHz ___ ______ ___ ______ ___ ______ ≤ 5.2 N/A 2 GHz ___ ______ ___ ______ ___ ______ ≤ 5.2 N/A 3 GHz ___ ______ ___ ______ ___ ______ ≤ 5.2 N/A Option 006 Channel A 4 GHz ___ ______ ___ ______ ___ ______ ≤ 5.2 N/A 5 GHz ___ ______ ___ ______ ___ ______ ≤ 5[...]

6-87 Performance T ests – Option 011 Performa nce T est Reco rds - Opt ion 011 T est 16. Source and Receiver Harmonics (Option 002 Only) (1 of 2) Test De scriptio n Ha rmonic Specific ation (dBc) Measureme nt Val ue Measu rement Unce rtaint y (dB) Sour ce Har monics 1.5 2nd < – 25 _ _______ _______ ± 1 1.0 3rd < – 25 _____ __________ ?[...]

6-88 Performanc e Tests – Opt ion 0 11 Perfor mance Test Record s - Option 011 2B : 3 r d < – 30 _ _______ _______ ± 1 Receiv er Har monic s 3 B : 2nd < – 15 _____ _______ ___ ± 1 2B : 3 r d < – 30 _ _______ _______ ± 1 3 A: 2nd < – 15 _____ _______ ___ ± 1 2A : 3 r d < – 30 _____ __________ ± 1 T est 16. Source and [...]

6-89 Performance T ests – Option 011 Performa nce T est Reco rds - Opt ion 011 T est 17. Receive r Magnitude Resp onse (Op t ion 002 Only) Analy zer Freque ncy Ext. Sour ce Freq uency Power Meter Value Input A Value Inpu t B Valu e Max. Dif f. Spec Spec. (dB) Meas . Uncer. (dB) 16 MHz 32 MHz _ ______ __ _____ ___ ____ _______ ± 1 ± 0.05 16 MHz [...]

[...]

7 If t he dis play does not light 7-2 If the fan does not run 7-3 If data entry ke ys don ’ t respond 7-3 If t here i s no RF sign al 7-4 Return ing the Instrum ent for Se rvice 7-5 Agilen t Technolog ies Service Offices 7-8 If Yo u Enco unte r a Prob lem[...]

7-2 If You Encoun ter a Prob lem If You Encounter a Pr oblem If You Encounter a Problem If you hav e difficu lty whe n instal ling or using the Agil ent 8 702D, che ck the fol- lowi ng l ist of comm only e ncountered p roblems a nd tr oubles hoot ing pr oce- dures. Contact the nearest Agilen t T echno logies offi ce for servic e, if necess ary . A [...]

7-3 If Y ou Enco unter a Probl em If the fan doe s not run WAR NI N G The power cord is conn ect ed to i ntern al capa cito rs tha t may rem ain live fo r 10 seconds af ter you disconne ct the co rd from the po wer supply. Figure 7-1. Line Fuse Remo val and Replacement WAR NI N G For co ntinued pr otec tion agai nst fire hazard , replace th e fuse [...]

7-4 If You Encoun ter a Prob lem If ther e is no RF si gnal The “ entry o ff ” is ena bled a fter yo u press the ENTRY OFF key . T o retu rn to nor- mal entr y mode, pr ess any funct ion key that has a numeric para meter associ - ated w ith i t. For exam ple, ST ART . ❒ Check that none of the key s are mechan ically stuck. ❒ Check that the [...]

7-5 If Y ou Enco unter a Probl em Returning the In stru ment for Se rvice Returning the Instrument for Service The instru ction s in this sec tion sho w yo u ho w to p roper ly return the i nstru - ment f or repair o r calibrati on. Always c all t he Agilent T echnol ogies I nstrument Suppo rt Center first to initi a te servi ce before retur ning y[...]

7-6 If You Encoun ter a Prob lem Returni ng the Instrumen t for Service infor matio n sho uld b e ret urned with the inst rument. • Type of ser vice required. • Date instrum ent was ret urned for repair. • Descri ption of th e proble m: • Whet her prob lem is co nstant or i ntermi ttent. • Wheth er inst rument is temp erature-s ensiti ve.[...]

7-7 If Y ou Enco unter a Probl em Returning the In stru ment for Se rvice Sealed Air Cor poration (Com merce, Cali fornia 90001). Air Cap looks like a plastic sh eet filled with air bubbl es. Use the pi nk (antistati c) Air Cap ™ to redu ce stat ic elect ricit y. Wra pping th e inst rument seve ral times i n this ma - teria l will prote ct the in[...]

7-8 If You Encoun ter a Prob lem Agil ent Tech nologi es Se rvice Offic es Agilent Technologies Service Offices Befor e returning an instru ment for ser vice, call the Ag ilent T echnologi es Instrumen t Suppo rt Center at (80 0) 403-0801, visit th e T es t and Measu rement W eb Sites by Count ry page at http ://www .tm .agilent. com/tmo /countr y/[...]

Index Index- 1 A accuracy and range of frequency, 4-3 accuracy and range o f frequency (Option 011), 6-3 accuracy of power test, 4-6 Agilent o ffices, 7-8 B backup disk, 1-26 C cabinet , cleanin g, iv , 1-2 calibra tion coefic ients test, 4-34 care of cab inet, iv , 1- 2 che ckin g t he o perati on, 1-16 classification product, iv cleaning cabine t[...]

Index -2 Index test port input fre quency response, 4-19 , 6-21 test port input impedanc e, 4-44 , 6-35 test port input noise floor level, 4-15 test port output frequency range and accu- racy, 4-3 test port output power acc uracy, 4-6 test port output power range and linearity, 4-8 , 6-5 test port receiver magnitude compress ion, 4-57 , 6-48 test p[...]

Index- 3 Index printer type, 1-13 problems, data entry controls do not respond, 7-3 problems, power-up display lights, but fan does not st art, 1-7 , 7-3 problems, RF output no RF signal at ei ther PORT 1 or PORT 2 , 7-4 procedures calibration coefficients, 4-34 external source mode frequency range, 4-5 minimum R cha nnel level, 4-10 , 6-9 , 6-12 s[...]

Index -4 Index test port output power range and linearity, 4-8 , 6-5 test port receiver magnitude compress ion, 4-57 , 6-48 test port receiver ma gnitude dynamic accu- racy, 4-48 , 6-39 test port receiver phase compression, 4-59 , 6-56 test port receiver phase dynamic accuracy, 4-55 , 6-47 syste m trace no ise test (with op tion 00 6), 4-42 syst em[...]