Allied Telesis AT-X510DP-52GTX Bedienungsanleitung

C613-04066-00 REV B AT-x510DP-52GTX Gigabit Ethernet Switch Installation Guide S2/52 S1/51 50 49 CONSOLE 2662 x510DP-52GTX SFP+ FDX HDX COL 1000 LINK ACT 10/100 LINK ACT 35 17 9 1 1 1 3 1 5 1 7 1 9 2 1 2 3 468 1 0 1 2 2 16 18 20 14 22 24 27 29 25 31 33 35 37 39 41 43 45 47 28 30 32 34 36 26 40 42 44 38 46 48[...]

Copyright © 2013 Allied Telesis, Inc. All rights reserved. No part of this pub lication may be reproduced without prior wr itten permission from Al lied Telesis, Inc. Allied Telesis and th e Allied Telesis logo are trademarks of Allied Telesis, Incor porated. All other product names, company nam es, logos or other designations me ntioned herein ar[...]

3 Electrical Safety and Emissions S tandards This product meets the following standards. RFI Emissions: FCC Class A, EN55022 Class A, EN61000-3-2, EN61000-3-3, VCCI Class A, C-TICK, CE EMC (Immunity): EN55024 Electrical Safety: EN60950-1 (UL-EU), UL 60950- 1 ( C UL US ) U.S. Federal Communications Commission Radiated Energy Note: This equipment has[...]

4 T ranslated Safety S tatements Important: Safety statements that have the  symbol are translated into multiple languages in the T ranslated Safety Messages document at alliedtelesis.com/support/d ocumentation .[...]

5 Preface .......................... ...................... ......................... ....................... ......................... ...... ........ ......................... ................ 11 Document Conventions ............. ............................ .............. ........... .............. ...................... ..... ............... .[...]

Contents 6 Unpacking the Switch .............. .............. .......................... ......................... .............. .............. ...................... ..........................55 Chapter 4: Installing the Switch and its Power Supplies ...................... ......................... ...................... .............. ..........[...]

7 Figure 1: Front Panel of the AT -x510DP-52GTX Switch ................ ............................ ............................ .... .......... ................ 18 Figure 2: Back Panel of the Switch .......... ......................... .............. ......................... .............. ..... ......... .......................... ....... 18 Fi[...]

Figures 8 Figure 50: Moving to the Global Configuration Mode with t he CONFIGU RE TERMINAL Comman d .......................... .........88 Figure 51: Activating VCStack with the STACK ENABLE Command ..................... .............. ................. ................ . . .......... ... 88 Figure 52: Returning to the Privilege d Exec Mode with th[...]

9 Ta b l e s Table 1: Twisted Pair Cable for the 10/100/1 000Base-T Po rts ............. .......................................... ............ ........................ 21 Table 2: LEDs on the 10/100/1000Base-T Ports ................ ............................ ............................ .......... .... ......................... .. 25 Table 3: [...]

Tables 10[...]

11 Pr eface This guide contains the in stallation instructions fo r the AT-x510DP-52GTX Gigabit Ethernet switch. This preface contains the following sections:  “Document Conventions” on p age 12  “Contacting Allie d T elesis” on p age 13 Note You can install AT-x510DP-52GTX switches as stand-alone devices or in a stack configuration w[...]

Preface 12 Document Conventions This document uses the following conventions: Note Notes provide additional informatio n. Caution Cautions inform you t hat performing or omitting a specific action may result in equipment damage or loss of data. Warning Warnings inform you that performing or omitting a sp ecific action may result in bodily injury.[...]

x510DP-52GTX Installation Gui de 13 Contacting Allied Telesis If you need assistance with this prod uct, you may contact Allied Telesis technical support by going to the Suppo rt & Services section of the Allied Telesis web site at www.alliedtelesis.com/support . You can find links for the following services on this page:  24/7 Online Suppor[...]

Preface 14[...]

15 Chapter 1 Overview This chapter contains the following sections:  “Features” on p age 16  “Front and Rear Panels” on p age 18  “Management Panel” on p age 19  “10/100/1000Base-T T wisted Pair Ports” on p age 20  “SFP+ Slot s” on page 22  “S tacking SFP+ Slots” on page 23  “eco-friendly Button” on [...]

Chapter 1: Ove rview 16 Features Here are the features o f the AT-x510DP-52GTX switch: 10/100/1000 Mbps Twisted Pair Ports Here are the basic features of the 10 /100/1000 Mbps twisted pair ports:  48 ports per switch  10Base-T, 100Base-TX, and 100 0Base-T compliant  IEEE 802.3u Auto-Negotiation compliant  Auto-MDI/MDIX  100 meters (3[...]

x510DP-52GTX Installation Gui de 17 Power Supply Modules The AT-x510DP-52GTX switch has two rear slots for hot-swap pable power supplies. Power supply options are:  For AC power with back-to-front a ir flow, one or two AT-PWR100R power supplies  For AC power with front-to-ba ck air flow, one or two AT-PWR250 power supplies  For DC power wi[...]

Chapter 1: Ove rview 18 Front and Rear Panels The front panel of the AT-x510DP-52GTX switch is shown in Figure 1. Figure 1. Front Panel of the AT -x510DP-52GTX Switch Figure 2 on page 18 shows the back pan el. Figure 2. Back Panel of the Switch 10/100/1000Base-T Ports SFP+ Slots Management Panel SFP+ or Stacking Slots S2/52 S1/51 50 49 CONSOLE 2662[...]

x510DP-52GTX Installation Gui de 19 Management Panel Figure 3 identifies the compone nts in the management panel on the AT- x510DP-52GTX switch. Figure 3. AT-x510DP-52GTX Management Panel Console eco-friendly Button Switch Port ID LED Management USB Port[...]

Chapter 1: Ove rview 20 10/100/1000Base-T Twisted Pair Ports The switches have 48 10/100/100 0Base-T ports. Speed The ports can operate at 10, 100, or 1 000 Mbps. The speeds may be set manually using the management softw are or automatically with Auto- Negotiation (IEEE 8 02.3u), the default setting. Note The ports must be set to Auto-Ne gotiation [...]

x510DP-52GTX Installation Gui de 21 The MDI and MDI-X settings do not ap ply when ports are operating at 1000 Mbps. Maximum Distance The ports have a maximum operating distance of 100 meters (328 feet). Cable Requirements The cable requirements of the ports are given in Table 1. Port Pinouts Refer to Table 11 on page 125 and Table 12 on pa ge 126 f[...]

Chapter 1: Ove rview 22 SFP+ Slots The switches have four SFP+ slots that support the following types of SFP 1000Mbps and SFP+ 10Gbp s transceivers:  1000Base-SX/LX SFP transceivers  Single-port BiDi 1000Base -LX SFP transceivers  1000Base-ZX SFP transceivers  10Gbps, 10GBase-SR/LR fiber optic transceivers  10Gbps AT-SP10TW direct co[...]

x510DP-52GTX Installation Gui de 23 Stacking SFP+ Slots Two of the four SFP+ slots on the front pa nel of the switch can be used with stacking transceivers to create a VCStack of up to four switches. The switches of a VCStack act as a single virtua l unit. They synchronize their actions so that switching operations, like spanning tree proto cols, v[...]

Chapter 1: Ove rview 24 eco-friendly Button You may turn off the port L E Ds to conserve electricity when yo u are not monitoring the switch. The LEDs are toggled with t he eco-friendly button on the front panel of the switch or the ECOFRIENDLY LED and NO ECOFRIENDLY LED commands in the Gl obal Configuration mode of the command line interface. The [...]

x510DP-52GTX Installation Gui de 25 LEDs Here are descriptions of the LEDs. LEDs for the Twisted Pair Ports Each twisted pair port has two LEDs th at display link, a c tivity and duplex mode information. The LEDs are shown in Figure 4. Figure 4. LEDs for the 10/100/1000Base-T Ports The LEDs are described in Table 2 on p age 25. Table 2. LEDs on the[...]

Chapter 1: Ove rview 26 LEDs for the SFP+ Slots The LEDs for the SFP+ slots are located between the slots, as shown in Figure 5. Each SFP+ slot has one LED. The left-hand LED is for the top slot and the right-hand LED is for the bottom slot. Figure 5. SFP+ Slot LEDs The LEDs are described in Table 3. Duplex Mode LED Green A port is operating in ful[...]

x510DP-52GTX Installation Gui de 27 LEDs for the Stacking Slots SFP+ slots 51 and 52 may be used as stacking slots to build a VCStack of up to four switches. For background information, refer to Chapter 2, “Virtual Chassis Stacking” on page 35 . Table 4 d efines the LED states when the slots contain stacking transceiver s. Switch ID LED The Swi[...]

Chapter 1: Ove rview 28 Figure 6. Switch ID LED The states of the LED when the switch is not operating in the low power mode are shown in Figure 7. Figure 7. Switch ID LED The switch displays the letter “F” for fault on the ID LED if it encounters one of the following problems:  A cooling fan has failed.  An unsupported power supply modul[...]

x510DP-52GTX Installation Gui de 29 Note You can use the SHOW SYSTEM ENVIRONMENT command in the command line interface to identify the source of the problem. The states of the LED when the switch is operating in the low power mode are shown in Figure 8. Figure 8. Switch ID LEDs in the Low Power Mode The switch is the master switch of a VCStack. The[...]

Chapter 1: Ove rview 30 USB Port The management panel has a USB port. You may use the port to store configuration files on flash drives and to restore the files to switches whose settings have been lost or co rrupted, or to quickly configure replacement units. You may also use the port and flash drives to update the management firmware on the swit [...]

x510DP-52GTX Installation Gui de 31 Console Port The Console port is used to establish a management session with the switch to configure its features a nd parameter settings. This type of management uses serial RS-23 2 and is commonly referred to as local or out-of-band management because it is not conducted over your network. To perform local mana[...]

Chapter 1: Ove rview 32 Power Supplies The AT-x510DP-52GTX switch has two rear slots for hot - swappable power supplies. The switch is supplied wit h a factory in stalled blank panel that covers both power supply slots, and with a separat e blank panel t o use if you only install one power supply. Power supply options a re:  For AC power with ba[...]

x510DP-52GTX Installation Gui de 33 Figure 9. AT-PWR100R AC Power Supply Figure 10. AT-PWR250 AC Power Supply Figure 11. AT-PWR250R DC Power Supply 2196 DC OUT F AUL T A T -PWR100R 100-240VAC~ 2A MAX 100-240 VAC~ 5A MAX DC PWR FAU LT A T -PWR250 2196 2197 FOR CENTRALIZED DC POWER CONNECTION, INS TALL ON L Y IN A RESTRICTED AREA. 40-60VDC 6A OUTPUT [...]

Chapter 1: Ove rview 34[...]

35 Chapter 2 V irtual Chassis S tacking The sections in this chapter are :  “Overview” on page 36  “S tacking Slo ts” on p age 37  “S tacking T ransce ivers” on page 38  “S tacking Port T opo logies” on page 40  “Master and Member Switches” on page 44  “S pecifying Ports in the Command Line Interface” on pa[...]

Chapter 2: Vi rtual Chassis Stac king 36 Overview Virtual Chassis Stacking (VCStack) a llows you to connect up to four switches to form a virtual switch in which the devices function as a single networking unit. The benefits of VCStack are:  Simplifies management - You can manage the devices of t he stack as a single unit, rather th an individua[...]

x510DP-52GTX Installation Gui de 37 Stacking Slots The AT-x510DP-52GTX switches come with two stackin g slots. The slots are the last two SFP+ slots on the switches and are labeled S1/51 and S2/ 52. The slots have two functions. You ma y use them with the VCStack feature to build a stack of switches or, by disa bling the VCStack feature, you may us[...]

Chapter 2: Vi rtual Chassis Stac king 38 Stacking Transceivers You connect the switches of the VCStack with the stacking transceivers listed in Table 5 and shown in Figure 12. Figure 12. Stacking Transceivers With its two SFP+ transceiver-style connectors a nd one meter of twinax cable, the AT-StackXS/1.0 transceiver is appropriate in situa tions w[...]

x510DP-52GTX Installation Gui de 39 Here are the transceiver guidelines:  The stacking transceivers may only be used in the stacking slots and only with the VCStack feature. You may not use the transceivers as regu lar networking ports.  The AT-StackOP/0.3 and AT-StackOP/9.0 transceivers must be connected to other AT-StackOP/0.3 and AT-StackO[...]

Chapter 2: Vi rtual Chassis Stac king 40 Stacking Port Topologies The switches of a stack are connected with the S1 and S2 ports and the stacking transceivers shown in Figu re 12 on page 38. There are two wiring configurations. The first topology is called the linear topology. In this topology the sw itches are connected with a single pathway. A st[...]

x510DP-52GTX Installation Gui de 41 The stack in Figure 14 on page 41 has four switches in the linear topology. Figure 14. Stack of Four Switches in the Line ar Topology The second topology is called the ring t opology. It is similar to the linear topology, except that the u nused stacking ports on the end switches of the stack are connected to for[...]

Chapter 2: Vi rtual Chassis Stac king 42 Figure 15. Stack of Two Switches in the Ring Topology Figure 16 on page 43 is an example of a stack of four switches in the ring topology. S2/28 S1/27 26 25 CONSOLE SFP+ S2/28 S1/27 26 25 CONSOLE SFP+ 2696[...]

x510DP-52GTX Installation Gui de 43 Figure 16. Stack of Four Switches in the Ring Topology The topologies are the same in terms of network speed and performance. However, the ring topology is the reco mmended wiring configuration because of the secondary path thro ugh the stacking ports. The two pathways protect the switches of the stack against th[...]

Chapter 2: Vi rtual Chassis Stac king 44 Master and Member Switches The stack has one master switch. The functions o f the master switch include:  Coordinating and monitoring stack operations.  Verifying that the switches ar e using the same version of management software. It automatically downloa ds its management software over the stacking [...]

x510DP-52GTX Installation Gui de 45 ID Numbers Each switch must be assigned an ID number. The range is 1 to 4 and the default is 1. The ID numbe rs are displayed on the ID LEDs on the front panels of the units. You may assign the nu mbers yourself or you can let the master switch assign the numbers automatically, as explained in Chapter 8, “Power[...]

Chapter 2: Vi rtual Chassis Stac king 46 Specifying Ports in the Command Line Interface The command line interface in the management software on the switch has a parameter that you use to specify the individual port s. The parameter is the PORT parameter and Figure 17 shows its format. Figure 17. PORT Parameter in the Comma nd Line Interface The fi[...]

47 Chapter 3 Beginning the Installation The chapter contains the following sections:  “Reviewing Safety Precautions” on p age 48  “Choosing a Site for the Switches” on p age 52  “Planning a S tack” on p age 53  “Unpacking th e Switch” on page 55[...]

Chapter 3: Be ginning the Install ation 48 Reviewing Safety Precautions Please review the following safety precautions before begin ning the installation procedure. Note Safety statements tha t have the  symbol are translated into multiple languages in the T ranslated Safety Messages document at www.alliedtelesis.com/support/documenta tion . War[...]

x510 Series Instal lation Guide for Virtual Chassis Stacking 49 Warning For AC PSUs, power cord is used as a disconnection device. T o de- energize equipment, disconnect the power cord.  E3 Warning Class I Equipment. This equipment must be earthed. The power plug must be connected to a properly wired eart h ground socket outlet. An improperly wi[...]

Chapter 3: Be ginning the Install ation 50 Caution Risk of explosion if battery is r eplaced by an incorrect type. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batterie s according to the manufacturer’s instructions. Attention: Le remplacement de la batte rie par une batterie de type incorrect peu[...]

x510 Series Instal lation Guide for Virtual Chassis Stacking 51 Warning Reliable earthing of rack-mounted equipment should be maint ained. Particular attention should be giv en to supply connections other than direct connections to the branch circ uit s (e.g., use of power strips).  E37 Caution The unit does not cont ain serviceable components. [...]

Chapter 3: Be ginning the Install ation 52 Choosing a Site for the Switches Observe these requirements when planning the installation of the switches of a stack.  If you plan to install the switches in an equipment rack, check to be sure that the rack is safely secured so that it will no t tip over. Devices in a rack should be installed starting[...]

x510 Series Instal lation Guide for Virtual Chassis Stacking 53 Planning a Stack Here are the guideline s to planning a stack:  A stack can have up to four switch es.  A stack can have different models of x510 Series switches. It cannot contain other switches, such as IX5 or x61 0 Series switches.  Any of the switches in the stack can b e [...]

Chapter 3: Be ginning the Install ation 54 Table 6. Operating Distances of the AT-StackOP/0.3 Transceiver Fiber Type Minimum Modal Bandwidth @ 850 nm (MHz*km) Operating Range 62.5/125 µm multi- mode fiber optic cable 160 2 to 26 meters (7 to 85 feet) 200 2 to 33 meters (7 to 108 feet) 50/125 µm multi- mode fiber optic cable 400 2 to 66 meters (7 [...]

x510 Series Instal lation Guide for Virtual Chassis Stacking 55 Unpacking the Switch Figure 18 lists the items that come with the switch. If any item is missin g or damaged, contact your Allie d Telesis sales representative for assistance. Figure 18. Components of the switch Note You should retain the original pac kaging material in the event you n[...]

Chapter 3: Be ginning the Install ation 56[...]

57 Chapter 4 Installing the Switch and its Power Supplies The procedures in this chap ter are:  “Installing the Power Cord Ret aining Clip” on page 58  “Installing Power Supply Modules” on page 59  “Installing the Switche s on a T able or Desktop” on page 63  “Installing the Switch in an Equipment Rack” on page 64  ?[...]

Chapter 4: Inst alling the Switch and i ts Power Supplies 58 Installing the Power Cord Retaining Clip This section applies to AC power supply modules. Perform the following procedure to in stall the power cord retaining clip on each power supply module: 1. Locate the power cord retaining clip, shown in Fig ure 19. Figure 19. Power Cord Retaining Cl[...]

x510DP-52GTX Installation Gui de 59 Installing Power Supply Modules Overview The AT-x510DP-52GTX switch has two rear slots for hot-swap pable power supplies. The switch is supplied with a factory installed blank panel that covers both power supply slots, and with a separate blank panel to use if you only install one power supply. Power supply optio[...]

Chapter 4: Inst alling the Switch and i ts Power Supplies 60 2. Remove the blank panel fro m the power supply slots on the rear panel of the switch by unscrewing it, as shown in the fo llowing figure. Figure 21. Removing the rear panel 3. Align the edges of th e power supply module with the guides in the slot and carefully slide the module into the[...]

x510DP-52GTX Installation Gui de 61 Figure 22. Installing the AT-PWR100R AC Power Supply Module 4. Secure the power supply module to the chassis by tightening the two captive screws with a cross-head screwdriver, as shown below. Figure 23. Securing the AT-PWR100R Power Supply Modu le 2268 DC OU T F AUL T A T -PWR100R 1 0 0 -240 VAC~ 2 A MAX 2269 DC[...]

Chapter 4: Inst alling the Switch and i ts Power Supplies 62 5. If you are going to operate the switch with a single power supply module, install the supplied blank panel over the second power supply module bay, as shown in the followin g figure. This is necessary for correct airflow. Figure 24. Installing the Blank Panel on the Power Supply Slot 6[...]

x510DP-52GTX Installation Gui de 63 Installing the Switches on a Table or Desktop You may install the switches on a table or desktop. Here are the guidelines to selecting a site:  The table should be level and stable .  The power outlets should be located near the switches and be easily accessible.  The site should allo w for easy access t[...]

Chapter 4: Inst alling the Switch and i ts Power Supplies 64 Installing the Switch in an Equipment Rack This procedure requires the following items:  Twelve bracket screws (included with the switch)  Two equipment rack brackets (included with the switch)  Flat-head screwdriver (not provided)  Cross-head screwdriver (not provid ed)  F[...]

x510DP-52GTX Installation Gui de 65 3. Turn the switch over. 4. Attach the two rack mount brackets to the sides of the switch using the bracket screws included with the unit. Figure 27 on page 65 illustrates the four possible bracket positions. Figure 27. Attaching the Equip ment Rack Bracke ts 2672 S 2 / 2 8 S 1 / 2 7 2 6 25 C ON S O L E S F P + x[...]

Chapter 4: Inst alling the Switch and i ts Power Supplies 66 5. While another person holds the switch in the equipment rack, secure it using standard equipment rack screws (not provided), as sho w n in Figure 28 for horizontal mountin g and Figure 29 for vertical mounting. Figure 28. Mounting the Switch Ho rizontally in an Equipment Rack Figure 29.[...]

x510DP-52GTX Installation Gui de 67 Connecting AC Power to a Power Supply Module To power on a switch with one or two AC Power Supply Modules, perfo rm the following procedure: 1. Position the power cord retaining clip in the up position, as shown in Figure 30. Figure 30. Power Cord Retaining Clip in the Up Position 2. Plug the power cord into the [...]

Chapter 4: Inst alling the Switch and i ts Power Supplies 68 3. Connect the other end of the power cord to an appropriate AC power outlet. For power specifica tions for the switch, refer to “Power Specifications” on page 124. Warning This unit might have more than one power supply. To reduce the risk of electric shock, disconnect all power cord[...]

x510DP-52GTX Installation Gui de 69 Power Wiring to a DC AT -PWR250R-80 Power Supply Module This section describes how to power on a switch with a DC AT-PWR250R-80 Power Supply Module, and essential safety information. Warning As a safety precaution, install a double-pole circuit breaker with a maximum value of 20 Amps and a minimum value of 15 Amp[...]

Chapter 4: Inst alling the Switch and i ts Power Supplies 70 as this equipment.  Switching or disconnecting devic es shall not be in the earthed circuit conductor between the DC sou rce and the point of connection of the earthing electrode conductor.  E55 Warning Enough wiring space is required to allow the conductors to be introduced and con[...]

x510DP-52GTX Installation Gui de 71 4. With a 14-gauge wire-stripping tool, strip the three wires in the tray cable coming from the DC input po wer source to 8mm ± 1mm (0.31 in., ± 0.039 in.), as shown in Figure 33 o n page 71. Warning Do not strip more than the recommended amount o f wire. Stripping more than the recommended amount can create a [...]

Chapter 4: Inst alling the Switch and i ts Power Supplies 72 6. Connect the +48 VDC (RTN) feed wire to the t erminal block marked +( p l u s ) . 7. Connect the -48 VDC feed wire to the terminal blo ck marked - (minus). Warning Check to see if there are any exposed copper strands coming from the installed wires. When this installation is done correc[...]

x510DP-52GTX Installation Gui de 73 Starting a Local Management Session This procedure requires a te rminal or a terminal emulator program and the management cable that comes with the switch. To start a local management session on the switch, p erform the following procedure: 1. Connect the RJ-45 connecto r on the management cable to the Console po[...]

Chapter 4: Inst alling the Switch and i ts Power Supplies 74 Monitoring the Initialization Processes It takes about thirty seconds for the switch to initialize its management software programs and features, and l oad t he default configuration. You may monitor the progress of the initializa tion process by watching the switch ID LED. It displays th[...]

x510DP-52GTX Installation Gui de 75 Figure 37. Switch Initialization Messages (Continued ) Starting ba se/loopback ... [ OK ] Starting ba se/sysctl.. . [ OK ] Received ev ent poefw.d one Starting ba se/portmapp er... [ OK ] Received ev ent syslog. done Starting ba se/reboot-s tability... [ OK ] Starting ba se/autofs-c ard... [ O K ] Checking sy ste[...]

Chapter 4: Inst alling the Switch and i ts Power Supplies 76 Figure 38. Switch Initia lization Messages (Continued) Assigning A ctive Workl oad to HA p rocesses: hsl, nsm, rm ond, sflowd, vrrpd , irdpd, la cpd lldpd, loop protd, mstp d, authd, e psrd, imi, imiproxyd Received ev ent network .activated Loading defau lt configurat ion Warning: flas h:[...]

77 Chapter 5 Configuring the Switch for S tand-alone Operations Use this chapter if you wish to oper ate the switch as a single stand-alone switch, instead of stacking it with other switches. This chapter contains the following pro cedures:  “Configuring the Switch for S tand-alone Operations” on p age 78  “S pecifying Ports in the Comm[...]

Chapter 5: Config uring the Switch for Sta nd-alone Operations 78 Configuring the Switch for Stand-alone Operations Disabling VCStack After the switch has initialized its management software, examine the switch ID LED on the front panel and do one of the following:  If the LED is displaying “0,” the installation pr ocedure is complete. The s[...]

x510DP-52GTX Installation Gui de 79 Note The User Exec mode is the first level in the comma nd mode interface. For complete information on the modes and command s, refer to the Sof tware Reference: AlliedWare Plus Operatin g System for x510 Series . 3. Enter the SHOW STACK command to display the status of the VCStack feature. Figure 40 is an exampl[...]

Chapter 5: Config uring the Switch for Sta nd-alone Operations 80 The ID parameter is the ID number of the switch, displayed on the ID LED. Replace the p arameter with whatever number is on the ID LED. For example, if the ID number of the switch is 1, th e default value, enter the command as follows: awplus(con fig)# no sta ck 1 enable This confirm[...]

x510DP-52GTX Installation Gui de 81 Confirming the Status of the VCStack Feature Another way to confirm that VCStack is disabled on the switch is by displaying the status of the last two SFP+ slots on the switch. These are slots 51 and 52. If VCStack is d isabled, you should be able to display the status of the slots even when they do not have tran[...]

Chapter 5: Config uring the Switch for Sta nd-alone Operations 82 The switch displays the message in Figure 46 on page 82 if VCS tack is not disabled, in which case you need to disable it by performing the commands in “Disabling VCS tack” on page 78. Figure 46. Status of a Stacking Slot When VCStack is Ena bled awplus# sho w interface port1.0.5[...]

x510DP-52GTX Installation Gui de 83 Specifying Ports in the Command Li ne Interface for Stand-alone Switches The command line interface in the manage ment software on the switch has a parameter that you use t o specify the individual ports. The parameter is the PORT parameter and Fig ure 47 shows its format. Figure 47. PORT Parameter in the Command[...]

Chapter 5: Config uring the Switch for Sta nd-alone Operations 84[...]

85 Chapter 6 V erifying the S tatus of VCS tack and Activating VCS t ack The procedures in this chap ter are:  “V erifying the S tatus of VCS tack” on p age 86  “Activating the VCS t ack Feature” on page 87[...]

Chapter 6: Verifyi ng the Status of VCStack a nd Activating VCStack 86 Verifying the Status of VCStack Before you install the stacking transcei vers to build the stack, you should first test the switches to determine wh ether the VCStack feature is enabled or disabled, and enable it o n any units where it is disabled. On new switches, the feature s[...]

x510DP-52GTX Installation Gui de 87 Activating the VCStack Feature Perform the following procedure to activate the VCStack feature on switches that display the numb er “0” on their ID LEDs in the previous procedure. The tasks follow on from “Monitoring the Initialization Processes” on page 74. Activating VCStack To activate VCStack, perform[...]

Chapter 6: Verifyi ng the Status of VCStack a nd Activating VCStack 88 4. Enter the CONFIGURE TERMINAL command to move to the Global Configuration mode, as sho wn in Figure 50. Figure 50. Moving to the Global Configuration Mode with the CONFIGURE TERMINAL Command 5. Enter the STACK ENABLE command to activate VCStack on the switch, as shown in Figur[...]

x510DP-52GTX Installation Gui de 89 8. Restart the switch with the REBOOT command, as sh own in Figure 54. Figure 54. Rebooting the Switch with the REBOOT Command 9. Type “Y” for yes. 10. Wait one minute for the switch to initialize its management software. 11. Check the ID LED and do one of the following:  If the ID LED is displaying the nu[...]

Chapter 6: Verifyi ng the Status of VCStack a nd Activating VCStack 90[...]

91 Chapter 7 Cabling the S t acking Ports This chapter contains the following pro cedures:  “Cabling Switches with A T -S ta ckXS/1.0 Tr ansceivers” on page 92  “Cabling Switches with A T -S ta ckOP/0.3 or A T -S tackOP/9.0 T ransceivers” on page 97[...]

Chapter 7: Cablin g the Stacking Port s 92 Cabling Switches with AT-StackXS/1.0 Transceivers To cable the switches of the st ack with AT-StackXS/1.0 transceivers, perform the following procedure: Warning A transceiver can be damaged by st atic electricity. Be sure to observe all standard electrosta tic discharge (ESD) pre cautions, such as wearing [...]

x510DP-52GTX Installation Gui de 93 3. Remove the dust cap from one end of the tran sceiver, as shown in Figure 56 on page 93. Figure 56. Removing the Dust Cover from the AT-StackXS/1.0 Transceiver[...]

Chapter 7: Cablin g the Stacking Port s 94 4. Position the transceive r with the release tab on top and slide the transceiver into the slot, as shown in Figure 57 on page 94 . Figure 57. Installing the AT-StackXS/1.0 Transceiver in Slot S1 S2/2 8 S1 /27 26 25 CON SO LE SFP+ 2683 Release tab[...]

x510DP-52GTX Installation Gui de 95 5. Remove the dust cover from the S2 slot in the n ext switch in the stack as shown in Figure 58 on p age 95. Note The cable must crossover to different slots on the switches. The stack will not work if you conne ct two S1 or S2 slots together. Figure 58. Removing the Dust Plug from the S2 Slot 6. Remove the dust[...]

Chapter 7: Cablin g the Stacking Port s 96 7. Position the transceiver with the release tab on the bottom and slide it into the slot until it clicks into pla ce, as shown in Figure 59 on page 96. Figure 59. Installing the AT-StackXS/1.0 Transceiver in Slot S2 8. Repeat this procedure to connect additi onal switches to the stack wit h AT-StackXS/1.0[...]

x510DP-52GTX Installation Gui de 97 Cabling Switches with AT-StackOP/0.3 or AT-StackOP/9.0 Transceivers For guidelines to cabling the switches with AT-StackOP/0.3 or AT- StackOP/9.0 fiber optic transceivers, refer to “Planning a Stack” on page 53. To cable switches with fiber optic tra nsceivers, perform the following procedure: 1. Remove a dus[...]

Chapter 7: Cablin g the Stacking Port s 98 3. Slide the transceiver into the slot until it clicks into place, as shown in Figure 61 on page 98. Figure 61. Installing the AT -StackOP/0.3 or AT-StackOP/9.0 Transceiver S2/2 8 S1 /2 7 26 25 CON SO LE SFP+ 2687 S2/2 8 S1 /27 26 25 CON SO LE SFP+ 2688[...]

x510DP-52GTX Installation Gui de 99 4. Remove the dust cover from the transceiver, as shown in Figure 62 on page 99. Figure 62. Removing the Dust Cover f rom a Stacking Transceiver 5. Verify the position of the handle on the transceiver. If the transceive r is in the S1 slot, the handle should be in the upright position, as shown in Figure 63. If t[...]

Chapter 7: Cablin g the Stacking Port s 100 6. Connect the fiber optic cable t o th e transceiver, as shown in Figure 64 on page 100. The connector on the cable should fit snugly into the port, and the tab should lock the con nector into place. Figure 64. Connecting the Fib er Optic Cable to the Stacking Transceiver 7. Repeat this procedure if the [...]

101 Chapter 8 Powering On the S tack This chapter contains the following pro cedures:  “Powering On the Switches Individually” on p age 102  “Powering On the Switches Simultaneously” on page 104  “V erifying the S t ack” on page 106 Perform “Powering On the Switches I ndividually” on page 102 if you want to control the assi[...]

Chapter 8: Po wering On the Stack 102 Powering On the Switches Individually This procedure explains how you can control the assignment of the ID numbers of the switches by powering on the units one at a time during the initial power-on sequence. The first sw itch is assigne d ID number 1, the next unit is assigned ID number 2, a nd so on. This proc[...]

x510DP-52GTX Installation Gui de 103 2. Wait one minute for the switch to in itialize its management software. The switch should be displaying the number 1 on it s ID LED. 3. Power on the switch to be assigned ID number 2. 4. Wait two minutes for the new switch to join the sta ck as a member. As the new switch boots up, the first switch, which has [...]

Chapter 8: Po wering On the Stack 104 Powering On the Switches Simultaneously If you want the switches of the stack to use their MAC addresses to automatically assign the ID numbers during the initial power on sequence, all you have to do is power them on simultaneously, rather than one at a time as in the previous procedure. Here are t he steps th[...]

x510DP-52GTX Installation Gui de 105 2. Wait two or three minutes for the switches to select a master switch and to assign the ID numbers. At this point, the stack is op erational. The ID numbers are automatically stored in special files in the flash memories of the switches and are ret ained by the devices even if you reset or power cycle the st a[...]

Chapter 8: Po wering On the Stack 106 Verifying the Stack To verify stack operations, per form the f ollowing procedure: 1. Establish a local management sessi on on any switch in the stack. Fo r instructions, refer to “Starting a Local Management Sessio n” on page 73. 2. From the User Exec mode, enter the SHOW STACK command: awplus> show st [...]

x510DP-52GTX Installation Gui de 107 Setting the Priority Numbers This procedure is optional. It explains ho w to configure the priority settings of the switches. Changing the priority se ttings protects the stack configuration should you e ver power on the stack with a new member switch that has a lower MAC address than an existing master or membe[...]

Chapter 8: Po wering On the Stack 108 4. Enter the WRITE command to save you r change in the configuration file. The switch displays the confirmation prompt in Figu re 68. Figure 68. Saving the Priority Values with the WRITE Comman d 5. To end the management session, enter the EXIT command. 6. Go to Chapter 9, “Cabling the Networking Ports” on [...]

109 Chapter 9 Cabling the Networking Ports This chapter contains the following pro cedures:  “Cabling the T wisted Pair Port s” on page 1 10  “Installing SFP and SFP+ T ransceivers” on p age 1 12[...]

Chapter 9: Cablin g the Networking Ports 110 Cabling the Twisted Pair Ports Here are the guidelines to cabli ng the 10/100 /1000Base-T twisted pair ports:  The cable specifications for the 10/100/1000Ba se-T twisted pair ports are listed in Table 1 on page 21 .  The connectors on the cables should fit snugly into the ports, and the tabs shoul[...]

x510DP-52GTX Installation Gui de 111  The default duplex mode set ting of Auto-Negotiation is not appropriate for ports connected to network devices that do not support Auto-Negotiation and have a fixed duplex mode. You should disable Auto-Negotiation on those ports and set their duplex modes manually to avoid the possibility of duplex mo de mis[...]

Chapter 9: Cablin g the Networking Ports 112 Installing SFP and SFP+ Transceivers Review the following guidelines before installing SFP or SFP+ transceivers in the switch:  SFP and SFP+ transceivers are hot-swappable. You may install them while the chassis is powered on.  Your Allied Telesis sa les representative can provide you with a list o[...]

x510DP-52GTX Installation Gui de 113 To install an SFP or SFP+ transceiver, perf orm the following procedure: 1. Remove the dust plug from a transceiver slot on the switch. Figure 69 on page 1 13 shows the dust plug being removed from a port. Figure 69. Removing the Dust Plug from an SFP+ Slot Note When VCStack is enabled on the switch , slots S1/5[...]

Chapter 9: Cablin g the Networking Ports 114 4. Slide the transceiver into the slot until it clicks into place, as shown in Figure 70 on page 114. Figure 70. Installing an SFP or SFP+ Transce iver Note If you are ready to attach the fiber optic cable to the transceiver, continue with the next step. Otherwise, repeat step s 1 to 4 to install the rem[...]

x510DP-52GTX Installation Gui de 115 6. Verify the position of the handle on the SFP transceiver. If the transceiver is in a top slot, the handle should be in the upright position, as shown in Figure 72 on page 115. If th e transceiver is in a bottom slot, the handle should be in the down position. Figure 72. Positioning the SFP or SF P+ Handle in [...]

Chapter 9: Cablin g the Networking Ports 116[...]

117 Chapter 10 T r oubleshooting This chapter contains suggestions on ho w to trou bleshoot the switch if a problem occurs. Note For further assistance, please contact Allied Te lesis Technical Support at www.alliedtelesis.com/support . Problem 1: The Switch ID LED on the front of the switch is off. The switch could be receiving no power, or the LE[...]

Chapter 10: Troubles hooting 118 — Try connecting the unit to another power source . — Try a different powe r cord. — Verify that the voltage from th e power source is within the required levels fo r your region.  If the PSU LED is not lit, then for DC power sup ply modules: — Verify whether the PSU is rece iving power. For example, list[...]

x510DP-52GTX Installation Gui de 119 Problem 4: A twisted pair port on the switch is connected to a network device but the port’s LINK/ACT LED is of f. Solutions: The port is unable t o establish a link to a network device . Try the following:  Verify that the port is connected to the co rrect twisted pair cable. This is to eliminate the possi[...]

Chapter 10: Troubles hooting 120  Verify that the correct type of fiber optic cabling is being used.  Verify that the port is connected to the correct fiber optic cable. This is to eliminate the possibility that the port is connected to the wrong remote network devi ce.  Try connecting another network device to the fiber optic port using a[...]

x510DP-52GTX Installation Gui de 121 Problem 8: The Switch ID LED on the front of the swit ch is flashing the letter “F.” Solutions: One or more of the following problems has occurred:  A cooling fan has failed.  An unsupported PSU has been installed.  One of the PSUs has failed.  The input voltage on one or both o f the PSUs is out[...]

Chapter 10: Troubles hooting 122[...]

123 Appendix A T echnical Specifications Physical Specifications Environmental Specifications Table 7. Physical Specifications Dimensions (H x W x D) 4.4 cm x 44.0 cm x 48.0 cm (1.7 in. x 17.3 in. x 18.9 in.) Weight 5.7 kg Recommended Minimu m Ventilation on All Sides 10 cm (4.0 in) Table 8. Environmental Specifications Operating Temperature 0° C [...]

Appendix A: Technica l Specifications 124 Power Specifications Certifications Table 9. Power Specifications Maximum Power Consumption 110W with two AT-PWR100R PSUs 130W with two AT-PWR250 PSUs 130W with two AT-PWR250R PSUs Input Voltage: AT-PWR100R PSU 100-240 VAC, 2 A maximum, 50/60 Hz per input Input Voltage: AT-PWR250 PSU 100-240 VAC, 5 A maximu[...]

x510DP-52GTX Installation Gui de 125 RJ-45 Twisted Pair Port Pinouts Figure 74 illustrates the pin layout of the RJ-45 connectors and p orts. Figure 74. RJ-45 Socket Pin Layout (Front View) Table 11 on page 125 lists t he pin signals for 10 and 100 Mbps. Table 11. Pin Signals for 10 an d 100 Mbps Pin MDI Signal MDI-X Signal 1T X + R X + 2T X - R X [...]

Appendix A: Technica l Specifications 126 Table 12 lists the pin signals when a p ort operating at 1000 Mbps. Table 12. Pin Signals for 1000 Mbps Pinout Pair 1P a i r 1 + 2P a i r 1 - 3P a i r 2 + 4P a i r 3 + 5P a i r 3 - 6P a i r 2 - 7P a i r 4 + 8P a i r 4 -[...]

x510DP-52GTX Installation Gui de 127 RJ-45 Style Serial Console Port Pinouts Table 13 lists the pin signals of the RJ-45 style serial Console port. Table 13. RJ-45 Style Serial Console Port Pin Sig nals Pin Signal 1 Looped to pin 8. 2 Looped to pin 7. 3 Transmit Data 4 Ground 5 Ground 6 Receive Data 7 Looped to pin 2. 8 Looped to pin 1.[...]

Appendix A: Technica l Specifications 128 Fiber Optic Specifications of the AT -StackOP/0.3 and AT-StackOP/9.0 Transceivers Table 14 lists the fiber optic port specifications for the AT-Sta ckOP/0.3 transceiver. Table 14. Fiber Optic Port Specif ications for the AT-StackOP/0.3 Module General Maximum Distances 33 m with 62.5/125 µm (core/ cladding)[...]

x510DP-52GTX Installation Gui de 129 Table 15 lists the fiber optic port sp ecifications for the AT-StackOP/9.0 transceiver. Table 15. Fiber Optic Port Spec ifications for the AT -StackOP/9.0 Transceiver General Maximum Distances 9 km Fiber Optic Cable 9/125 µm (core/cladding) single- mode fiber optic cable Transmitter Wavelength 1310 nm Output Op[...]