Deutsch dropdown-ico

American Dryer Corp. AD-15 Phase 7 Bedienungsanleitung

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31

Zur Seite of

Ähnliche Gebrauchsanleitungen

Richtige Gebrauchsanleitung

Die Vorschriften verpflichten den Verkäufer zur Übertragung der Gebrauchsanleitung American Dryer Corp. AD-15 Phase 7 an den Erwerber, zusammen mit der Ware. Eine fehlende Anleitung oder falsche Informationen, die dem Verbraucher übertragen werden, bilden eine Grundlage für eine Reklamation aufgrund Unstimmigkeit des Geräts mit dem Vertrag. Rechtsmäßig lässt man das Anfügen einer Gebrauchsanleitung in anderer Form als Papierform zu, was letztens sehr oft genutzt wird, indem man eine grafische oder elektronische Anleitung von American Dryer Corp. AD-15 Phase 7, sowie Anleitungsvideos für Nutzer beifügt. Die Bedingung ist, dass ihre Form leserlich und verständlich ist.

Was ist eine Gebrauchsanleitung?

Das Wort kommt vom lateinischen „instructio”, d.h. ordnen. Demnach kann man in der Anleitung American Dryer Corp. AD-15 Phase 7 die Beschreibung der Etappen der Vorgehensweisen finden. Das Ziel der Anleitung ist die Belehrung, Vereinfachung des Starts, der Nutzung des Geräts oder auch der Ausführung bestimmter Tätigkeiten. Die Anleitung ist eine Sammlung von Informationen über ein Gegenstand/eine Dienstleistung, ein Hinweis.

Leider widmen nicht viele Nutzer ihre Zeit der Gebrauchsanleitung American Dryer Corp. AD-15 Phase 7. Eine gute Gebrauchsanleitung erlaubt nicht nur eine Reihe zusätzlicher Funktionen des gekauften Geräts kennenzulernen, sondern hilft dabei viele Fehler zu vermeiden.

Was sollte also eine ideale Gebrauchsanleitung beinhalten?

Die Gebrauchsanleitung American Dryer Corp. AD-15 Phase 7 sollte vor allem folgendes enthalten:
- Informationen über technische Daten des Geräts American Dryer Corp. AD-15 Phase 7
- Den Namen des Produzenten und das Produktionsjahr des Geräts American Dryer Corp. AD-15 Phase 7
- Grundsätze der Bedienung, Regulierung und Wartung des Geräts American Dryer Corp. AD-15 Phase 7
- Sicherheitszeichen und Zertifikate, die die Übereinstimmung mit entsprechenden Normen bestätigen

Warum lesen wir keine Gebrauchsanleitungen?

Der Grund dafür ist die fehlende Zeit und die Sicherheit, was die bestimmten Funktionen der gekauften Geräte angeht. Leider ist das Anschließen und Starten von American Dryer Corp. AD-15 Phase 7 zu wenig. Eine Anleitung beinhaltet eine Reihe von Hinweisen bezüglich bestimmter Funktionen, Sicherheitsgrundsätze, Wartungsarten (sogar das, welche Mittel man benutzen sollte), eventueller Fehler von American Dryer Corp. AD-15 Phase 7 und Lösungsarten für Probleme, die während der Nutzung auftreten könnten. Immerhin kann man in der Gebrauchsanleitung die Kontaktnummer zum Service American Dryer Corp. finden, wenn die vorgeschlagenen Lösungen nicht wirksam sind. Aktuell erfreuen sich Anleitungen in Form von interessanten Animationen oder Videoanleitungen an Popularität, die den Nutzer besser ansprechen als eine Broschüre. Diese Art von Anleitung gibt garantiert, dass der Nutzer sich das ganze Video anschaut, ohne die spezifizierten und komplizierten technischen Beschreibungen von American Dryer Corp. AD-15 Phase 7 zu überspringen, wie es bei der Papierform passiert.

Warum sollte man Gebrauchsanleitungen lesen?

In der Gebrauchsanleitung finden wir vor allem die Antwort über den Bau sowie die Möglichkeiten des Geräts American Dryer Corp. AD-15 Phase 7, über die Nutzung bestimmter Accessoires und eine Reihe von Informationen, die erlauben, jegliche Funktionen und Bequemlichkeiten zu nutzen.

Nach dem gelungenen Kauf des Geräts, sollte man einige Zeit für das Kennenlernen jedes Teils der Anleitung von American Dryer Corp. AD-15 Phase 7 widmen. Aktuell sind sie genau vorbereitet oder übersetzt, damit sie nicht nur verständlich für die Nutzer sind, aber auch ihre grundliegende Hilfs-Informations-Funktion erfüllen.

Inhaltsverzeichnis der Gebrauchsanleitungen

  • Seite 1

    AD-15 Phase 7 Installa tion Manual American Dryer Corporation 88 Currant Road Fall River MA 02720-4781 USA T elephone: (508) 678-9000 / Fax: (508) 678-9447 e-mail: techsupport@amdry .com www .amdry .com W ARNING: For your safety the information in this manual must be followed to minimize the risk of fire or explosion or to prevent property damage, [...]

  • Seite 2

    Ret ain This Manual In A Safe Place For Future Reference American Dryer Corporation product s embody advanced concepts in engineering, design, and safety . If this product is properly maintained, it will provide many years of safe, efficient, and trouble free operation. ONL Y qualified technicians should service this equipment. OBSERVE ALL SAFETY P[...]

  • Seite 3

    IMPORT ANT YOU MUST DISCONNECT AND LOCK OUT THE ELECTRIC SUPPL Y AND THE GAS SUPPL Y OR STEAM SUPPL Y BEFORE A NY COVERS OR P ANELS ARE REMOVED FROM THE MACHINE TO ALLOW ACCESS FOR CLEANING , ADJUSTING , INST ALLA TION, OR TESTING OF ANY EQUIPMENT PER OSHA (Occupational Safety and Health Administration) ST ANDARDS. Caution: Label all wires prior[...]

  • Seite 4

    2 American Dryer Corp. 1 13243-1 SAFETY PRECAUTIONS W ARNING: For your safety , the information in this manual must be followed to minimize the risk of fire or explosion or to prevent property damage, personal injury , or loss of life. The dryer must never be operated with any of the back guards, outer tops, or service panels removed. PERSONAL INJU[...]

  • Seite 5

    1 13243-1 www.amdry.com 3 SPECIFICA TIONS Shaded areas are stated in metric equivalents 1/30/04 * Size of piping to dryer varies with installation conditions. Contact factory for assistance. ** Specify air-operated or electromechanical steam damper system. Air-operated steam damper system must be provided with clean, dry , regulated 80 psi +/- 10 p[...]

  • Seite 6

    4 American Dryer Corp. 1 13243-1 INST ALLA TION PROCEDURES Installation should be performed by competent technicians in accordance with local and state codes. In the absence of these codes, the installation must conform to applicable American National St andards: ANSI Z223.1-LA TEST EDITION (National Fuel Gas Code) or ANSI/NFP A NO. 70-LA TEST EDIT[...]

  • Seite 7

    1 13243-1 www.amdry.com 5 DRYER ENCLOSURE REQUIREMENTS Bulkheads and partitions should be made of noncombustible materials and must be located a minimum of 12-inches (30.48 cm) above the dryers outer top; 18-inches (45.72 cm) for steam dryers, except along the front of the dryer which may be closed if desired. X = 12-inch (30.48 cm) minimum, 24-[...]

  • Seite 8

    6 American Dryer Corp. 1 13243-1 CAUTION: This dryer produces combustible lint and must be exhausted to the outdoors. When possible, it is suggested to provide a separate (single) exhaust duct for each dryer . CAUTION: IMPROPERL Y SIZED OR INST ALLED EXHAUST DUCTWORK CAN CREA TE A POTENTIAL FIRE HAZARD . The exhaust ductwork should be laid out in s[...]

  • Seite 9

    1 13243-1 www.amdry.com 7 Illus. C IMPORT A NT : No more than eight (8) dryers maximum should be connected to one (1) main common duct with a vertical run. VERTICAL VENTING When vertical single 10-inch (25.4 cm) venting is used (refer to Illus. B below ), the ductwork from the dryer to the outside outlet cannot exceed 60 feet (18.28 meters), refer [...]

  • Seite 10

    8 American Dryer Corp. 1 13243-1 Illus. C (refer to the previous page) shows the minimum cross section area for multiple dryer venting. These figures must be increased in proportion if the main duct run from the last dryer to where it exhausts has numerous elbows or is unusually long. IMPORT A NT : For extended ductwork runs, the cross section area[...]

  • Seite 11

    1 13243-1 www.amdry.com 9 NOTE: ADC reserves the right to make changes in specifications at any time without notice or obligation. Electrical Service S pecifications IMPORT A NT : Figures shown are for non-reversing models only . For reversing models contact the factory . Gas and S team Models O nly * 3-Wire available. 1/30/04 Electric Models Only [...]

  • Seite 12

    10 American Dryer Corp. 1 13243-1 For added personal safety , when possible, it is suggested that a separate ground wire (no. 18 minimum) be connected from the ground connection of the dryer to a grounded cold water pipe. DO NOT ground to a gas pipe or hot water pipe . The grounded cold water pipe must have metal-to-metal connection ALL the way to [...]

  • Seite 13

    1 13243-1 www.amdry.com 11 The neutral will only be used on 4-wire service. This is typical for 380-416V , 50 Hz. Electrically Heated Models Only The only electrical input connections to the dryer are the 3-phase (3ø) power leads (L1, L2, L3, and sometimes neutral) and ground. Single-phase (1ø) power for the control circuit and for any single-pha[...]

  • Seite 14

    12 American Dryer Corp. 1 13243-1 GAS INFORMA TION It is your responsibility to have ALL plumbing connections made by a qualified professional to ensure that the gas plumbing installation is adequate and conforms with local and state regulations or codes. In the absence of such codes, ALL plumbing connections, materials, and workmanship must confor[...]

  • Seite 15

    1 13243-1 www.amdry.com 13 STEAM INFORMA TION It is your responsibility to have ALL plumbing connections made by a qualified professional to ensure that the gas plumbing installation is adequate and conforms with local and state regulations or codes. Care must be exercised when leveling steam dryers into final position. After leveling the dryer , c[...]

  • Seite 16

    14 American Dryer Corp. 1 13243-1 2 SHUDW L QJ 6WHDP  3UHVVXU H IMPORT A NT : Coil failure due to improper pH level will VOID THE W ARRANTY . S team Requirement s Shaded areas are stated in metric equivalents * The minimum operating pressure is 100 psig (689.47 kPa) for optimum fresults. Installation Instructions T o ensure an adequate supply[...]

  • Seite 17

    1 13243-1 www.amdry.com 15 S team Damper Air System Connections The dryer is manufactured with a pneumatic (piston) damper system, which requires an external supply of compressed air . The air connection is made to the steam damper solenoid valve, which is located at the rear inner top area of the dryer just in front of the electric service relay b[...]

  • Seite 18

    16 American Dryer Corp. 1 13243-1 S team Damper Air Piston (Flow Control) Operation Adjustment Damper operation was tested and adjusted prior to shipping at 80 psi (5.51 bar). If damper air adjustment is necessary , locate the flow control valve and make the necessary adjustments as noted below . PREOPERA TIONAL TESTS ALL dryers are thoroughly test[...]

  • Seite 19

    1 13243-1 www.amdry.com 17 PREOPERA TIONAL INSTRUCTIONS Coin Models Microprocessor Controller (Computer) When the microprocessor controller (computer) is in the ready state, the liquid crystal display (L.C.D.) screen will display Ready , Insert $XX.XX (amount) to S tart. Insert coin(s). Once the correct Amount to St art has been inserte[...]

  • Seite 20

    18 American Dryer Corp. 1 13243-1 Mechanical Drop/Rotary Coin Meter or Slide Coin Meter  Insert coin and turn knob (rotary type meter), or for slide meter unit, push in coin chute.  Select T emperature.  Push the S tart button.  T o stop dryer, open the main door . Non-Coin Models The light emitting diode (L.E.D.) display reads ?[...]

  • Seite 21

    1 13243-1 www.amdry.com 19 IMPORT A NT : A separate warranty card must be completed and returned for each individual dryer . NOTE: Be sure to include the installation date when returning the warranty card(s). W ARRANTY For a copy of the ADC commercial warranty covering your particular dryer(s), contact the ADC reseller from whom you purchased the e[...]

  • Seite 22

    20 American Dryer Corp. 1 13243-1 ALL returns must be properly packaged to ensure that they are not damaged in transit. Damage claims are the responsibility of the shipper. IMPORT A NT : No replacements, credits, or refunds will be issued for merchandise damaged in transit. ALL returns should be shipped to the ADC factory in such a manner that they[...]

  • Seite 23

    1 13243-1 www.amdry.com 21 THE DA T A LABEL  MODEL NUMBER The model number is an ADC number , which describes the size of the dryer and the type of heat (gas, electric, or steam).  SERIAL NUMBER The serial number allows ADC to gather information on your particular dryer .  MANUF ACTURING CODE NUMBER The manufacturing code number is a numbe[...]

  • Seite 24

    22 American Dryer Corp. 1 13243-1 PROCEDURE FOR FUNCTIONAL CHECK OF REPLACEMENT COMPONENTS Microprocessor Controller (Computer) Board Phase 7 Coin Models  Upon completing installation of the replacement microprocessor controller (computer) board, reestablish power to the dryer .  S tart the drying cycle by pressing any temperature selection k[...]

  • Seite 25

    1 13243-1 www.amdry.com 23 For Models with Johnson Direct S p ark Ignition (DSI) Controller (G760) Theory of Operation: S tart the drying cycle. When the gas burner ignites within the chosen trial for ignition time (6-seconds), the flame sensor detects gas burner flame and signals the DSI module to keep the gas valve open as long as there is a call[...]

  • Seite 26

    24 American Dryer Corp. 1 13243-1 MANUAL RESET BURNER HI-LIMIT INSTRUCTIONS PHASE 7 This dryer was manufactured with a manual reset burner hi- limit thermostat, which is monitored by the Phase 7 computer . If the burner hi-limit is open prior to the start of the drying cycle, the dryer will start momentarily and then shut down, the Phase 7 computer[...]

  • Seite 27

    1 13243-1 www.amdry.com 25 The exclusive Sensor Activated Fire Extinguishing (S.A.F .E.) System will extinguish fires that may start in the drying basket (tumbler). A series of sensors positioned throughout the basket (tumbler) and interfaced with the microprocessor will trigger the S.A.F .E. system water jet(s) to quickly extinguish the flames. Th[...]

  • Seite 28

    26 American Dryer Corp. 1 13243-1 IMPORT A NT : Flexible supply line/coupling must be used. Solenoid valve failure due to hard plumbing connections WILL VOID W ARRANTY. It is recommended that a filter or strainer be installed in the water supply line. T ypical water supply: OPTIONAL MANUAL BYP ASS Provisions are made in the dryer S.A.F .E. system f[...]

  • Seite 29

    1 13243-1 www.amdry.com 27 W ARNING: If the water in the supply line or water solenoid valve freezes, the S.A.F .E. system will be INOPERA TIVE !! The manual ball cock shutoff valve must be located outside of the dryer at a distance from the dryer where it is easily accessible. Electrical Requirements No independent external power source or supply [...]

  • Seite 30

    28 American Dryer Corp. 1 13243-1 S.A.F .E. SYSTEM DIAGNOSTICS MESSAGES OPEN THERMISTOR PROBE  This message indicates that the S.A.F .E. system thermistor probe either is not connected or is damaged. If this condition is detected, the Phase 7 non- coin control will immediately enter S.A.F .E. SYSTEM DISABLED mode. SHORTED THERMISTOR PROBE  Th[...]

  • Seite 31

    ADC 1 13243 1- 2/03/04 - 50[...]