American Power Conversion S20BLK Bedienungsanleitung
- Schauen Sie die Anleitung online durch oderladen Sie diese herunter
- 54 Seiten
- 0.4 mb
Zur Seite of
Ähnliche Gebrauchsanleitungen
-
Power Supply
American Power Conversion 5000VA 5U
14 Seiten 1.44 mb -
Power Supply
American Power Conversion AP9555
16 Seiten 0.41 mb -
Power Supply
American Power Conversion RS-232
2 Seiten 0.38 mb -
Power Supply
American Power Conversion 120-160kW
32 Seiten 0.96 mb -
Power Supply
American Power Conversion 450 VA
16 Seiten 0.42 mb -
Power Supply
American Power Conversion Back-UPS CS 500
2 Seiten 0.35 mb -
Power Supply
American Power Conversion HS 500
4 Seiten 5.82 mb -
Power Supply
American Power Conversion 250
36 Seiten 0.26 mb
Richtige Gebrauchsanleitung
Die Vorschriften verpflichten den Verkäufer zur Übertragung der Gebrauchsanleitung American Power Conversion S20BLK an den Erwerber, zusammen mit der Ware. Eine fehlende Anleitung oder falsche Informationen, die dem Verbraucher übertragen werden, bilden eine Grundlage für eine Reklamation aufgrund Unstimmigkeit des Geräts mit dem Vertrag. Rechtsmäßig lässt man das Anfügen einer Gebrauchsanleitung in anderer Form als Papierform zu, was letztens sehr oft genutzt wird, indem man eine grafische oder elektronische Anleitung von American Power Conversion S20BLK, sowie Anleitungsvideos für Nutzer beifügt. Die Bedingung ist, dass ihre Form leserlich und verständlich ist.
Was ist eine Gebrauchsanleitung?
Das Wort kommt vom lateinischen „instructio”, d.h. ordnen. Demnach kann man in der Anleitung American Power Conversion S20BLK die Beschreibung der Etappen der Vorgehensweisen finden. Das Ziel der Anleitung ist die Belehrung, Vereinfachung des Starts, der Nutzung des Geräts oder auch der Ausführung bestimmter Tätigkeiten. Die Anleitung ist eine Sammlung von Informationen über ein Gegenstand/eine Dienstleistung, ein Hinweis.
Leider widmen nicht viele Nutzer ihre Zeit der Gebrauchsanleitung American Power Conversion S20BLK. Eine gute Gebrauchsanleitung erlaubt nicht nur eine Reihe zusätzlicher Funktionen des gekauften Geräts kennenzulernen, sondern hilft dabei viele Fehler zu vermeiden.
Was sollte also eine ideale Gebrauchsanleitung beinhalten?
Die Gebrauchsanleitung American Power Conversion S20BLK sollte vor allem folgendes enthalten:
- Informationen über technische Daten des Geräts American Power Conversion S20BLK
- Den Namen des Produzenten und das Produktionsjahr des Geräts American Power Conversion S20BLK
- Grundsätze der Bedienung, Regulierung und Wartung des Geräts American Power Conversion S20BLK
- Sicherheitszeichen und Zertifikate, die die Übereinstimmung mit entsprechenden Normen bestätigen
Warum lesen wir keine Gebrauchsanleitungen?
Der Grund dafür ist die fehlende Zeit und die Sicherheit, was die bestimmten Funktionen der gekauften Geräte angeht. Leider ist das Anschließen und Starten von American Power Conversion S20BLK zu wenig. Eine Anleitung beinhaltet eine Reihe von Hinweisen bezüglich bestimmter Funktionen, Sicherheitsgrundsätze, Wartungsarten (sogar das, welche Mittel man benutzen sollte), eventueller Fehler von American Power Conversion S20BLK und Lösungsarten für Probleme, die während der Nutzung auftreten könnten. Immerhin kann man in der Gebrauchsanleitung die Kontaktnummer zum Service American Power Conversion finden, wenn die vorgeschlagenen Lösungen nicht wirksam sind. Aktuell erfreuen sich Anleitungen in Form von interessanten Animationen oder Videoanleitungen an Popularität, die den Nutzer besser ansprechen als eine Broschüre. Diese Art von Anleitung gibt garantiert, dass der Nutzer sich das ganze Video anschaut, ohne die spezifizierten und komplizierten technischen Beschreibungen von American Power Conversion S20BLK zu überspringen, wie es bei der Papierform passiert.
Warum sollte man Gebrauchsanleitungen lesen?
In der Gebrauchsanleitung finden wir vor allem die Antwort über den Bau sowie die Möglichkeiten des Geräts American Power Conversion S20BLK, über die Nutzung bestimmter Accessoires und eine Reihe von Informationen, die erlauben, jegliche Funktionen und Bequemlichkeiten zu nutzen.
Nach dem gelungenen Kauf des Geräts, sollte man einige Zeit für das Kennenlernen jedes Teils der Anleitung von American Power Conversion S20BLK widmen. Aktuell sind sie genau vorbereitet oder übersetzt, damit sie nicht nur verständlich für die Nutzer sind, aber auch ihre grundliegende Hilfs-Informations-Funktion erfüllen.
Inhaltsverzeichnis der Gebrauchsanleitungen
-
Seite 1
User Manual Network Manageable S T ype Power Conditioner With Battery Backup Model: S20BLK[...]
-
Seite 2
Entire contents copyright © 2007 Americ an Power C onversion Corpora tion. All rights reserved. Reproduction in whole or in part without permission is prohibit ed. APC, the APC logo, and TRADEMARK NAMES are trade marks of American Power Conversion Corpora tion. All other trademarks , product names, and corporate names are the property of their res[...]
-
Seite 3
i Safety Information 1. Read this ma nua l - Read all of the safety and operating instru ctions before installing and operatin g this device. 2. Keep this ma nua l - Retain this ma nual, and all of the s a fety information that came with this device. 3. W arnings - Comply with all warnin gs presented in thi s m anual, as well as any warnings found [...]
-
Seite 4
ii 15. Power Lines - Do not locate outside antenna systems near overhead power lines, or other electric light or power ci rcuits, or where they may fall on or otherwise come in contact with these power sources. If you allow the ladder being used, or the antenna itself to come into contact with these power sources it could be fatal. 16. Overload ing[...]
-
Seite 5
iii Registration V erification Confirmation Registering your pur - chase now guaran- tees that you will receive all the infor- mation and special offers you qualify for as the owner of this product. Registering your pur - chase now provides you with a way to con- firm yourself as the owner of the product in the event of fire, theft or loss. Registe[...]
-
Seite 6
iv Class B Labeling and Instruction Manua l Requirement s Devices subject to Certification must be labeled with a Federal Communica- tions Commission (FCC) Identifier . Devices subjec t to V erification or Certifica- tion must be labeled with the following compliance statement: This device complies with Part 15 of the FCC Rules. Operation is subjec[...]
-
Seite 7
v T able of Content s Page Safety Information i Protect Your Investment iii Chapter 1 - Introduction 1-1 Proven Expertise… Prov en Reliability 1-1 Package Contents 1-2 Safety Precautions 1-2 Unit Power Capacity 1-2 Features 1-3 Communications and Management 1-3 Environmental Monitoring 1-4 Pure Sine Wave Battery Backup 1-4 Automatic Voltage Regul[...]
-
Seite 8
vi Page Connecting the Components 2-12 S20BLK Setup 2-13 Chapter 3 - Trou bleshooting 3-1 Unit will not turn on. 3-2 Connected equipment r eboots or turns off during or after the unit switches to battery power 3-2 REPLACE BATTERY LED is illuminated 3-3 Contact Information 3-3 Limited Warranty 3-4 Appendix A - Specifications A-1 Appendix B - Network[...]
-
Seite 9
1-1 Chapter 1 Introduction Figure 1. S20BLK Power Conditioner with Battery Backup (Front View) Proven Expertise… Proven Reliability From corporate data centers to home of fices, APC is regard ed as a leading innovator , designer and manufacturer of high-quality power protection solutions. With its proven reputation for Legendary Reliability TM , [...]
-
Seite 10
1-2 Package Content s Y our S20BLK Power Co nditioner package should contain the following: Safety Precautions Ensure you have read and understand all of the safety informat ion located in the front of this manual. If you have any questions concerni ng any of the safety information, or if you are concerned that your home may no t be properly wired [...]
-
Seite 11
1-3 Features The S20BLK Power Conditioner ’ s major features are described in the following paragraphs. Communications and Management A universal serial bus (USB) port, RS-232 port, and Network Managem ent Card (embedded W eb server) provide m ultiple methods for monitoring and managi ng the S20BLK, and the equipment connected to it. For example,[...]
-
Seite 12
1-4 Network Management Card An Ethernet port is located on the S20BLK rear panel, and enables the S20BLK’ s embedded Network Management Card (NMC) to connect to any Ethernet network. The NMC (W eb server) enables users to re motely monitor and mana g e th e S20BLK from any W eb browser . All 12 outlets can be si multaneously turned OFF or ON via [...]
-
Seite 13
1-5 Isolated Noise Filter Banks The S20BLK isolated noise filer banks (I NFB) eliminate electromagnetic and radio frequency interference (EMI and RFI) that , when severe enough, can negatively impact sound and video quality . Each filter bank is electrically isolated from the other filter banks to prevent noise generat ed by one component from poll[...]
-
Seite 14
1-6 Figure 2. Front Panel Co ntrols and Indicators DELA YED 1 S tatus Indicator When lit (blue), conditioned power is being supp lied to equipment connected to the rear-p anel outlets marked Switched Delayed 1 . ON BA TTER Y St a t u s I n d i c a t o r When lit (orange), the Power Conditioner is operating on pow er from th e internal Battery Pack [...]
-
Seite 15
1-7 V acuum Fluorescent Display The vacuum fluorescent display (VFD) conveys unit and power statu s information. It is also used to display information when changing unit settings. Note: The VFD and light emitting diod es (LEDs) can be dimmed or turned off independently of ea ch other via the front control panel SETUP push button . Up Arr ow Pus h [...]
-
Seite 16
1-8 Down Arr o w Push Button This pushbutton is used to change (decrease or turn off) parameters for various user-selectable settings such as: Audible Alarms, Sensitivit y , Display Dimmer , LED Dimmer , Go T o Bat If, Outlet 1 & 2 Delay (in seconds), Low Bat W arning, Bat Rep Date , and so on. On/Off Switch This switch controls power to all of[...]
-
Seite 17
1-9 Rear Panel Controls and Connectors The rear panel connectors for the S20BLK Conditioner are shown in Figure 3. Each numbered callout corresponds to a numbered descripti on in th e list that follows Figure 3. Figure 3. Rear Panel Co nnectors, Ind icator, and Ci rcuit Breake r Note: All outlets provide su rge protection, volt age regulation, nois[...]
-
Seite 18
1-10 Outlets - These include the two rows of six outlets (total of 12 outlets) on the rear of the S T ype Power Conditioner , shown in Figure 3. These outlets are arranged based on the type of filtering protection ( DIGIT AL, VIDEO, ANALOG) , and isolated noise filte r banks (INFBs) eliminate electromagnetic interference (EMI) and radio frequency i[...]
-
Seite 19
1-11 CIRCUIT BREAKER – A press-to-r eset ci rcuit breaker is prov id ed. When it is “tripped ” due to an electrical surge or overload, it pops out and shuts down output power to the ou tlets. T o reset the Circuit Breaker , press it in. Caution: When resetting the Circuit Breaker, push the button in quickly, and release the button. Do not hol[...]
-
Seite 20
1-12 RS-232 Port The RS-232 serial port allows you to monito r and m anage the S20BLK, and also provides the ability to integrate the S20BLK into your home automation network . Note: This port can only b e functi onal when the USB cable is not connected to the S20BLK. Surge Protected T elephone Jacks ( TEL/DVR/SA T/DSL ) The S20BLK has a telephone [...]
-
Seite 21
2-1 Chapter 2 Inst allation This chapter contains th e following procedures: • Removing the Battery Pack • Installing the Unit • Inserting and Connecting the Battery • Powering On and Connecting Equipm ent • Performing the System Test • Status and Informational Screens • Connecting the Components • S20BLK Setup Using Front Panel Con[...]
-
Seite 22
2-2 Inst alling the Unit The S20BLK may be installed on a flat, solid surface or rack-mounted. Proper placement of the S20BLK should be accomplished in accordance with the following proced ures: Inst alling the Unit on a Flat Surface Place the unit on a solid, flat surface that is capable of supporting at least 60 lbs. Note: Avoid placing other com[...]
-
Seite 23
2-3 Inserting and Connecting the Battery In accordance with APC’ s interpretation of Department of T ransportation regulations, APC ships this device with the in ternal battery pack disconnected. The front bezel of the unit is also not attached to the unit when it is sh ipped. This procedure is for c onnecting the battery when the front bezel has[...]
-
Seite 24
2-4 Figure 5. Battery Wire Connection Caution: Failure to install the battery retaining bar can be hazardous. 4. Install the battery retaining bar . 5. Install the front bezel , as shown in Figure 6, by aligning the four pins located on the back-side of the bezel with the holes in the left and right sides of the unit. Gently push the fr ont bezel i[...]
-
Seite 25
2-5 Powering On and Connecting Equipment 1. Power on the S20BLK unit and perform system test. 2. Connect the equipment. 3. Connect the data line cables. 4. Power on the connected equipment. Performing the System T est Before connecting eq uipment to the S2 0BLK Power Conditioner, ensure that the unit is functional by connectin g the AC Po wer Cord [...]
-
Seite 26
2-6 Figure 9. DELA YED OUTLET1: ON; DELA YED OUTLET1: OFF Screen SELFTEST IS ON; ON-LINE SELFTEST — is shown in Figure 10, and indicates that SELFTEST IS ON , and ON-LINE SELFTEST is active. This SELFTEST is conducted using utility power . Figure 10. SELFTEST IS ON; ON-LINE SELFTEST Screen SELFTEST IS ON; ON-BA TTER Y SELFTEST — Figure 1 1 show[...]
-
Seite 27
2-7 SELFTEST RESUL T ; SELFTEST HAS P ASSED — Figure 13 displays the message TEST HAS P ASSED , which indicates that self-test ran successfully to completion. If the messag e T EST HAS F AILED is displayed, please contact APC T echnical Support. Figure 13. SELFTEST RESUL T ; SELFTEST HAS P ASSED Screen DA T A PORT : USB REMOVED — Figur e 14 dis[...]
-
Seite 28
2-8 S t atus and Informational Screens The following paragraphs describe the vari ous status and informationa l screens that are available w ith the S20BLK. St atus Screens The most important status screens available after the Selftest has completed include: • INPUT VOLTAGE: XXXV; OUTPUT VOLTAGE: XXXV • SYSTEM LOAD: <XXXW; LOAD: <XX X% ?[...]
-
Seite 29
2-9 EST. RUNTIME: XHRS; FUEL: XXX% This message is show n in Figure 17. Each un it can also display the estimated runtime as EST . RUNTIME (in hou rs), as well as the FUEL capacity of the internal battery pack (as a percentage) based on the tota l load connected to the device. If the estimated runtime is < 1 hour , the EST . RUNTIME will show in[...]
-
Seite 30
2-10 SOURCE: XXXXXXX; EST. RUNTIME: XHRS Screen This screen, shown previously in Fig ure 19, indicates which type of sour ce the unit is deriving power from ( UTILITY , BA TTERY , or ST ANDBY ). It also displays the EST . RU NTIME (in hours) based on the power source, and connected equipment LOAD . In St andby , the unit does not provi de an output[...]
-
Seite 31
2-11 Model Number and Serial Number Screen This screen, shown in Figure 22, provides informat ion about th e S20BLK that you have purchased. It also provides the correct serial number for the uni t. Note: Always have this information available any time you contact APC Technical Support. You should al so have the firmware version. Figure 22. Model a[...]
-
Seite 32
2-12 Outlet Status Screens The two screens in Figures 25 and 26 sh ow which of the four outlet banks are turned on or off. The outlet banks can be turned on or of f independently via the RS-232 serial port, which is located on the rear of the unit. In th e near future this capability will also be available via the W eb. Refer to Appendix B for dir [...]
-
Seite 33
2-13 S20BLK Setup Y ou can use the front panel SETUP and Arrow Up/Down pushbuttons to configure (turn on or off) various functions provi ded by each S20BLK unit. When you press the SETUP pushbutton, the unit fu nctions are displayed in the followin g order: 1. Audible Alarm 2. Sensitivity 3. Display Dimmer 4. LED Dimmer 5. Go To Battery If <X X [...]
-
Seite 34
2-14 AUDIBLE ALARM Setting – When the alarm is set to ON , as shown in Figure 27, it indicates an abnormal conditio n with the power or unit. It provides an audible tone (beep) whenever the unit detects an internal pr oblem, or a problem wi th an externally connected battery pack. When it is set to OFF the audible tone is silenced. Figure 27. AUD[...]
-
Seite 35
2-15 Figure 29. DISPLAY DIMM ER (HIGH) Setting Screen LED DIMMER Setting — This screen, shown in Figure 30, lets you set a brightness level of HIGH , LOW , or OFF for the front-panel light emitting diode (LED) indicators. Use the SETUP pushbutton to advance to the LED DIMMER screen (not shown). Once the display is shown, press the Up Arrow and Do[...]
-
Seite 36
2-16 OUTLET DE LA Y1 and OUTLET DELA Y2 — These settings let you set a defined time delay ( 0 to 10 seconds) for when the unit provides power to the rear panel outlet marked Switched Delayed1 ( TUNER/AUX ), or Switched Delayed2 ( SUBWOOFER and/or AMPLIFIE R ). By setting this delay it prevents power on o r power off glitches from affecting othe r[...]
-
Seite 37
2-17 Figure 36. DO QUIK SELFTEST Screen DO RUNTIME CAL Setting — This function, show n in Figure 37, allows you to manually initiate a Runtime Calculation test to calibrate internal measurements, which should result in more accurate runt ime estimates. This should be done once every six months, or when the connect ed load size changes significant[...]
-
Seite 38
2-18 SCREEN SA VER: ON/OFF Setting — This function, shown in Figure 40, allows you to force the unit to continuously alternate a message S20 POWER CONDITIONER WITH BA TTER Y BACKUP between the two li nes of fi elds on the VFD. This feature h elps to maintain disp lay quality , as well as extendin g the life of the VFD. Note: Even when the screen [...]
-
Seite 39
3-1 Chapter 3 T roubleshooting This chapter describes some possib le problems that might occur , and the probable causes and solutions. They include: 1. Unit will not turn on. 2. The AV equipment connected to the S Type unit re boots or turns of f during or after the unit switches to bat tery powe r. 3. The REPLACE BATT ERY indicato r is on (lit). [...]
-
Seite 40
3-2 Connected equipment reboot s or turns off during or after the unit is on battery power Note: The unit will not turn on and a ccept incoming utility power if the power is out of range. The unit can still be "cold-started" using battery power by pressing and ho lding the power switch in until the unit beeps. Probable Cause: Circuit brea[...]
-
Seite 41
3-3 REPLACE BA TTER Y LED is illuminated Cont act Information Always ensure that you hav e the model number , serial number and firmwar e version of your unit at hand any time you contact APC T echnical Support . T echnical Support General Information Probable Cause: Battery is nearing the end of its useful life. Solution: Based on the dat e of pur[...]
-
Seite 42
3-4 Limited W arranty American Power Conversion (APC) warrants it s products to be free from defects in materials and work mansh ip for a period of two years from the da te of purchase. Its obligation under this warranty is lim it ed to repairing or replacing, at its own sole option, any such d efective products. T o ob tain service under warrant y[...]
-
Seite 43
A-1 Specifications A T echnical Specifications The table on the foll owing pages contai ns the technical sp ecifications for the S20BLK Power Condit ioner . Note: The input co ntact and output relay features listed on the UP S Networ k Card Environment Web page do not apply to the S20BLK Power Conditioner. FCC Compliance Information These devices c[...]
-
Seite 44
A-2 S20BLK External Battery Pack (SBA TT & SBA TTBLK) Input: V oltage Range for Operatin g on Utility 92V to 142V N/A Nominal V oltage 120 V a c 48 Vdc Allowable Frequency for Operat ing on Utility 47 to 63 Hz N/A Rated Input Current 12 Amps N/A Circuit Breaker Rating 15 Amps N/A Output: Number of Outlets 12 (all outlets surge protected, condit[...]
-
Seite 45
A-3 Communication USB T ype B, low speed N/A RS-232 DB9 female, 2400-8-N-1 N/A Network RJ45. 10/100T Ethernet (Auto Detect) N/A Surge Protection: Let-Through V oltage Rating <50V N/A Data Line Protection Jacks RJ45 N/A Coaxial Cable 2 pair N/A T elephone/DSL 2 line, 4wire with spli tter N/A Physical: Unit Dimensions 17 x 5.25 x 18.55 in 43.2 x 1[...]
-
Seite 46
A-4[...]
-
Seite 47
B-1 Network Card B This appendix contains descriptions and instructi ons to assist tho se persons responsible for the configuration and setup of the S20B LK, which con tains an embedded Network Management Card (NMC), also simply call ed the APC Management Card. Note: The input contact and output relay features listed on the UPS Network Card Environ[...]
-
Seite 48
B-2 NMC Major Features The Network Management Card (NMC) has the follow ing key features: • Autosenses 10/100 MBS connection speeds • Provides a data log accessible by FTP, SCP or a W eb browser • Supports remote monitoring serv ices • Provides UPS scheduling features • Supports the APC PowerChute ® Netw ork Shu tdo wn utility • Provid[...]
-
Seite 49
B-3 Reference Document s The APC Network Management Car d utility CD contains the following documentation: • Network Management Card User’s Guide • PowerNet MIB Reference Guide • CD-ROM contents file (.Contentscontent s.h tm) • Network Management Card Release Notes • Troubl eshooting d ocuments Quick Configuration This section covers [...]
-
Seite 50
B-4 The Device IP Configuration W izard runs on Microsoft W in dows 2000, 2003, and W indows XP operating systems. For more information concerning W izard installation, configuration, reconfigu ration, retrievi ng and exportin g .i ni files, uploading events and error messages, refer to the APC Device IP Configuration Wi z a rd section in the Netwo[...]
-
Seite 51
B-5 Control Console Once you log onto the control console, as described in either the Local (Serial) Access, or ARP and T elnet Access section above, perform the followin g steps: 1. Choose Network from the Control Console menu. 2. Choose TCP/IP from the Network menu. 3. Disable BOOTP (if it is enab led), and select Ac cept Changes . 4. Set the Sys[...]
-
Seite 52
B-6 How to Access the NMC The following paragraphs describe the vari ous ways you can use different interfaces to access the NMC when it is running on your network. Note: For more detailed information ab out how to use these interfaces, reference the APC Network Management Card User’s Guide. We b Interface The W eb interface provides options to m[...]
-
Seite 53
[...]
-
Seite 54
APC W orldwide Customer Support Customer support for this or any other APC product is available at no charge in any of the following ways: • V isit the APC W eb site to access do cuments in the APC Knowledge Base and to submit customer support requests. – www .apc.com (Corporate Headquarters) Connect to localized APC W eb sites for specific cou[...]