Avaya P330-ML-ML Bedienungsanleitung

Avaya Reference Guide A VAYA P330-ML-ML S TACKABLE S WITCH S OFTWARE V ERSION 4.5 January 2004[...]

[...]

Avaya P330-ML Reference Guide Contents Chapter 1 Using the CLI ............. ...................... ....................... ...................... ...................... 1 CLI Architecture........................ ....................... ....................... ...................... ..... 1 Conventions Used ....... ....................... .........[...]

Table of Contents ii Avaya P330-ML Reference Guide copy module-config tftp .......... ....................... ......................... ............. 16 copy running-config scp . ......................... ....................... ..................... 17 copy running-config startu p-config .......... ....................... .................. 18 cop[...]

Table of Contents Avaya P330-ML Reference Guide no rmon history .... ....................... ...................... ....................... ............ 46 no snmp-server ............. ....................... ....................... ...................... .... 46 no snmp-server engineID ............. .......................... .....................[...]

Table of Contents iv Avaya P330-ML Reference Guide set interface inband .................. ....................... ......................... ............. 67 set interface ppp ..................... ...................... .......................... ............... 67 set interface ppp enable/enable-alwa ys/disable/off/reset ....... .... 68 set inter[...]

Table of Contents Avaya P330-ML Reference Guide set port negotiation ...................... ...................... ....................... ............ 94 set port point-to-point admin status ........................ ......................... . 95 set port powerline ..................... ......................... ....................... ...........[...]

Table of Contents vi Avaya P330-ML Reference Guide set spantree hello-time ............... ....................... ......................... ........ 117 set spantree max-age ..................... .......................... ...................... ..... 118 set spantree priority ....................... .......................... ....................[...]

Table of Contents Avaya P330-ML Reference Guide show ip access lists ............. .......................... ...................... ................ 140 show ip access-list-summary ................... ......................... ................ 141 show ip route ............... ...................... ....................... ........................[...]

Table of Contents viii Avaya P330-ML Reference Guide show rmon statistics ................... .......................... ...................... ........ 177 show secure current ............... ...................... ....................... ................ 178 show secure mac ...................... ....................... ......................... [...]

Table of Contents Avaya P330-ML Reference Guide Router Configuration Contexts . ......................... ......................... ..... 211 Shortcuts to Commands by Context ..................... ...................... ..... 211 General Commands ..................... ....................... ......................... .................. 212 arp ....[...]

Table of Contents x Avaya P330-ML Reference Guide ip max-arp-entries ....................... ....................... ......................... ........ 234 ip max-route-entries ......................... ....................... ......................... .. 235 ip netmask-format .................... ....................... ......................... .[...]

Table of Contents Avaya P330-ML Reference Guide show ip route summary ...................... ....................... ........................ 260 show ip ssh ............... ...................... ....................... ......................... ..... 260 show ip srrp ...................... ....................... ...................... ..........[...]

Table of Contents xii Avaya P330-ML Reference Guide ip srrp backup ...................... ......................... ....................... ................ 286 ip vlan/ip vlan name ........................ .................... ...................... ........ 286 ip vrrp ..................... ...................... .......................... ......[...]

Avaya P330-ML Reference Guide 1 Chapter 1 Using the CLI This chapter describes the Avaya P330 CLI architecture and conventions, and provides instructions for accessing the Avaya P330 for configu ration purposes. The configuration procedure involves establishing a Telnet session or a serial connection and then using the Avaya P330’s internal CLI. [...]

Chapter 1 Using the CLI 2 Avaya P330-ML Reference Guide Conventions Used The following conventions are used in this chapter to convey instructions and information: • Mandatory keywords ar e in boldface. • Variables that you supply are in pointed brackets <>. • Optional keywords are in square brackets []. • Alternative but mandatory ke[...]

Chapter 1 Using the CL I Avaya P330-ML Reference Guide 3 Command Syntax Commands are not case-sensitive. That is, uppercase and lowercase characters may be interchanged freely. Command Abbreviations All commands and parameters in the CLI can be truncated to an abbreviation of any length, as long as the abbreviation is not ambiguous. For example, ve[...]

Chapter 1 Using the CLI 4 Avaya P330-ML Reference Guide Universal Commands Universal commands are commands that can be issued anywhere in the hierarchical tree. Top and Up commands The Up command moves you up to the next highest level in the CLI command hierarchy. The Top command moves you to the highest level. Retstatus command Use the retstatus c[...]

Chapter 1 Using the CL I Avaya P330-ML Reference Guide 5 To configure the switch parameters, on module 6, type the command: session 6 switch . Note: When you use the session command the security level stays the same. Note: Use the session command without a ny parameters to identify the stack master and its slot number . It will li st all the module[...]

Chapter 1 Using the CLI 6 Avaya P330-ML Reference Guide Security Levels There are four security access levels – User, Privileged, Configure and Supervisor. • The User level is a general access level used to show system param eter values. • The Privileged level is used by site personnel to access stack configuration options. • The Configure [...]

Chapter 1 Using the CL I Avaya P330-ML Reference Guide 7 Entering the CLI To enter the CLI, e nter your username and password. Your access level is indicated in the prompt as follows: The User level prompt is shown below: P330-N> The Privileged level prompt is shown below: P330-N# The Configure level prompt for Layer 3 configuration is shown bel[...]

Chapter 1 Using the CLI 8 Avaya P330-ML Reference Guide[...]

Avaya P330-ML Reference Guid e 9 Chapter 2 Avaya P330-ML Layer 2 CLI Commands This chapter describes all the P330-ML Layer 2 CLI commands and parameters in alphabetical order. clear cam User level: privileged, supervisor. Use the clear cam command to delete all entries from the CAM table. The syntax for this command is: clear cam Example: clear dot[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 10 Avaya P330-ML Reference Guide clear dynam ic vlans User level: privileged, supervisor. L This command is available on the P330-ML-ML only. Use the clear dynamic vlans command to clear dyna mically learned VLANs. Only the VLANs learned by the switch from incoming traffic are cleared using this command.[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 11 Example: clear logging server User level: privileged, supervisor. Use the clear logging server command to delete a S yslog server from the Syslog server table. The syntax for this command is: clear logging server <ip-address> Example: clear port mirror User level: [...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 12 Avaya P330-ML Reference Guide clear port static-vlan User level: privileged, supervisor. Use the clear port static-vlan command to delete VLAN s statically configured on a port. The syntax for this command is: clear port static-vlan [module/port range][vlan num] Example: clear radius auth entication s[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 13 Example: clear screen User level: user, privileged, supervisor Use the clear screen command to clear the current terminal display. The syntax for this command is: clear screen clear secure mac User level: user, privileged, supervisor L If this command is to be implemente[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 14 Avaya P330-ML Reference Guide clear snmp trap User level: privileged, supervisor. Use the clear snmp trap command to clear an entry from th e SNMP trap receiver table. The syntax for this command is: clear snmp trap {<rcvr_addr>|all} Example: clear timezone User level: privileged, supervisor. Us[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 15 The syntax for this command is: clear utilization cpu <module-number> Example: clear vlan User level: privileged, supervisor. Use the clear vlan command to delete an existing VLAN and return ports from this VLAN to the default VLAN #1. When you clear a VLAN , all p[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 16 Avaya P330-ML Reference Guide The syntax for this command is: copy module-config scp <filename> <ip> <mod_num> Example: copy module-config tftp User level: superviso r Use the copy module-config tftp command to upload the switch-level parameters from the current NVRAM running configu[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 17 Example: copy running-config scp User level: supervisor Use the copy running-config scp command to upload the current switch-level parameters from the current NVRAM running configuration into a file via SCP. The syntax for this command is: copy running-config scp <fil[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 18 Avaya P330-ML Reference Guide Example: copy running-confi g startup-config User level: superviso r L This command applies to the P334T-ML only when it is in “Layer2” device mode. Use the copy running-config startup-config command to copy the active policy configuration to the startup conf iguratio[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 19 Example (for Windows): Example: (for Unix): ip The ip address of the tftp server. P330-N# copy running-config tftp c:P330-MLstartup.cfg 149.49.100.41 P330-N# copy running-config tftp /folder/P330- ML/startup.cfg 149.49.100.41[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 20 Avaya P330-ML Reference Guide copy scp module-config User level: superviso r Use the copy scp module-config command to download a mod u le configuration to the device via SCP. L Only parameters that differ from the factory default settings for the switch are included in the configuration file. Therefo[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 21 Example: (for Unix): copy scp stack-config User level: supervisor Use the copy scp stack-config command to download a stack configuration to the device via SCP. L Only parameters that differ from the fa ctory default settings for the s witch are included in the conf igur[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 22 Avaya P330-ML Reference Guide Example (for Windows): Example: (for Unix): P330-N# copy scp stack-config c:P330-MLstack.cfg 149.49.100.41 Username: 330user Password: Beginning download operation ... This operation may take a few minutes... Please refrain from any other operation during this time. For[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 23 copy scp startup-confi g User level: supervisor Use the copy scp startup-config command to download a startup configuration to the device via SCP. L Only parameters that differ from the fa ctory default settings for the s witch are included in the conf iguration file. Th[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 24 Avaya P330-ML Reference Guide Example: (for Unix): copy stack-config scp User level: superviso r Use the copy stack-config scp command to upload the switch-level parameters from the active bank into a file via SCP. The syntax for this command is: copy stack-config scp <filename> <ip> <m[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 25 Example: copy stack-config tft p User level: supervisor Use the copy stack-config tftp command to upload the stack-level parameters from the current NVRAM r unning configurat ion into a file via TFTP. L Create the file into which you wish to upload the stack-level parame[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 26 Avaya P330-ML Reference Guide copy startup-config scp User level: superviso r Use the copy startup-config scp com mand to upload the switch-level startup configuration from the active bank into a file via SCP. The syntax for this command is: copy startup-config scp <filename> <ip> <mod_[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 27 The syntax for this command is: copy startup-config tftp <filename> <ip> Example (for Windows): Example: (for Unix): copy tftp EW_archive User level: supervisor Use the copy tftp EW-archive command to download the P330-ML Manager application into the switch f[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 28 Avaya P330-ML Reference Guide copy tftp module-conf ig User level: superviso r Use the copy tftp module-config command to download the switch-level configuration from a saved f ile into the current NVRAM running configuration of a switch from a TFTP server. L Only parameters that differ from the facto[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 29 The syntax for this command is: copy tftp stack-config <filename> <ip> Example (for Windows): Example (for Unix): copy tftp startup -config User level: supervisor L This command applies to the P334T-ML only when it is in “Layer2” device mode. Use the copy[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 30 Avaya P330-ML Reference Guide Example: (for Unix): copy tftp SW_image User level: superviso r Use the copy tftp SW_image command to download a new firmware software version into bank B while ei ther keeping the old version in bank A, or downloading the Embedded Web manager software into bank A. The sy[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 31 Example: P330-N# copy tftp SW_image /home/P33 0-ML/viisa EW_archive 1 135.64.103.104 1 Module : 1 Source file : /home/P330-ML/vii sa Destination file : P330-ML Host : 135.64.103.104 Running state : Download Process Started Failure display : no-error Last warning : - ....[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 32 Avaya P330-ML Reference Guide copy tftp SW_powerinlin e_image User level: superviso r L This command applies to P333T-PWR switches only and is used by P330- ML-ML switches to control P333T-PWR modules in the stack. Use the copy tftp SW_powerinline_image command to update the inline software applicatio[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 33 The syntax for this command is: crypto key generate dsa [ key-size <key-length>] Example: dir User level: user, privileged, supervisor Use the dir command to show the file types that have been downloaded to the switch. The syntax for this command is: dir [module_nu[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 34 Avaya P330-ML Reference Guide Output Fields: L If N/A is displayed for the EW_Archive file, this mea ns that the Device Manager software is not loaded correctly. Download the Device Manager software again. disconnect ssh User level: superviso r Use the disconnect ssh command to disconnect an SSH sessi[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 35 The syntax for this command is: disconnect ssh <session-id> Example: get time User level: privileged, supervisor. Use the get time command to retrieve the time from the network. The syntax for this command is: get time Example: help User level: user, privileged, su[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 36 Avaya P330-ML Reference Guide Example: hostname User level: privileged, supervisor. Use the hostname co m mand to change the Command Line Interface (CLI) prompt. Th e curr ent modu le number alwa ys appears at the end of the prompt. Use the no hostname command to return the CLI prompt to its default .[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 37 contains several of thes e rules: each rule pertains to the source IP addres s, the destination IP address, the protocol, the pr otocol ports (if relevant), and to the ACK bit (if relevant). Use the no ip access list command to delete a specific rule. The syntax for this[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 38 Avaya P330-ML Reference Guide L The P334T-ML does not support ‘lt’ and ‘gt’ port operators. ip access-list-c ookie User level: superviso r L This command applies to the P334T-ML only when it is in device mode "Layer2". Use the ip access-list-cookie command to set the list cookie f or[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 39 ip access-defa ult-action User level: supervisor L This command applies to the P334T-ML only when it is in device mode "Layer2". Use the ip access-default-action command to set the default action for a specific policy list . The syntax for this command is: ip a[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 40 Avaya P330-ML Reference Guide Example: ip access -list-dscp trust User level: superviso r L This command applies to the P334T-ML only when it is in device mode "Layer2". Use the ip access-list-dscp trust command to decide which original frame priority to trust for the placement of the frame [...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 41 ip access-list-name User level: supervisor L This command applies to the P334T-ML only when it is in device mode "Layer2". Use the i p access-list-name command to assign a nam e to a policy list. The syntax for this command is: ip access-list-name <policy-li[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 42 Avaya P330-ML Reference Guide ip http ena ble User level: superviso r Use the ip http enable command to enable HTTP acce ss to the device. The syntax for this command is: ip http enable Example: ip icmp redirect User level: superviso r Use the ip icmp redirect command to enable ICMP redirects via the [...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 43 Example: ip ssh enable User level: supervisor Use the ip ssh command to enable t he SSH server. The syntax for this command is: ip ssh enable Example: ip telnet enable User level: supervisor Use the ip telnet enable command to enable Telnet access to the device. The synt[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 44 Avaya P330-ML Reference Guide ip telnet-client enable User level: superviso r Use the ip telnet-client enable command to enable the device to act as a Telnet client. L This command can only be run from the c onsole port on the device. The syntax for this command is: ip telnet-client enable Example: no[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 45 no ip ssh User level: supervisor Use the no ip ssh command to disable the SSH server. The syntax for this command is: no ip ssh Example: no ip telnet User level: supervisor Use the no ip telnet command to disable Te lnet access to the device. The syntax for this command [...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 46 Avaya P330-ML Reference Guide Example: no rmon alarm User level: privileged, supervisor. Use the no rmon alarm command to delete an existing RMON alarm entry. The syntax for this command is: no rmon alarm <Alarm Index> Example: no rmon event User level: privileged, supervisor. Use the no rmon ev[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 47 no rmon history User level: privileged, supervisor. Use the no rmon history command to delete an existing RMON history entry. The syntax for this command is: no rmon history <History Index> Example: no snmp-server User level: supervisor Use the no snmp-server comma[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 48 Avaya P330-ML Reference Guide no snmp-server comm unity User level: superviso r Use the no snmp-server comm unity command to deny access to the device using community strings. The syntax for this command is: no snmp-server community Example: no snmp-server group User level: superviso r Use the n o snm[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 49 no snmp-server host User level: supervisor Use the no snmp-server host command to either delete the host from the trap recipients list or, if noti fications types are specified in the command, disable the specified notifications for the host. The syntax for this command [...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 50 Avaya P330-ML Reference Guide Example: no snmp-serve r notifications User level: superviso r Use the no snmp-server noti fications command to disable all available SNMP notifications. The syntax for this command is: no snmp-server notifications Example: no snmp-server remote-user User level: superviso[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 51 The syntax for this command is: no snmp-server user <username> { v1 | v2c | v3 } Example: no snmp-server view User level: supervisor Use the no snmp-server view command to remove a view or remove OIDs from a view. The syntax for this command is: no snmp-server view[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 52 Avaya P330-ML Reference Guide The syntax for this command is: no username <name> Example: If you wish to delete a name which includes spaces, you must enclose the e ntire name in quotation marks, for example “new york”. L You cannot delete the default user account “root”. nvram initi ali[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 53 The syntax for this command is: ping [host[number]] Example: to ping the IP ad dress 149.49.48.1 three times: prompt-length User level: supervisor Use the prompt-length command to specify the length of the default CLI prompt. The syntax for this command is: prompt-length[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 54 Avaya P330-ML Reference Guide User level: user, privileged, supervisor Use the reset command t o restart the stack or an individual switch. If no switch number is defined or the switch number of the Master is defined, the command resets the entire stack. If the switch number is defined, the command re[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 55 reset stack User level: privileged, supervisor. Use the reset stack command to perform a hardware re set of the entire stack. The syntax for this command is: reset stack reset wan User level: user, privileged, supervisor Use the reset wan command to perform a software re[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 56 Avaya P330-ML Reference Guide rmon alarm User level: privileged, supervisor. Use the rmon alarm command to create a new RMON alarm entry. The syntax for this command is: rmon alarm <Alarm Number> <variable> <interval> <sample type> rising-threshold <rising threshold> <[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 57 rmon event User level: privileged, supervisor. Use the rmon event command to create an RMON event entry. The syntax for this command is: rmon event <Event Number> <type> description <description> owner <owner> Example: rmon history User level: pri[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 58 Avaya P330-ML Reference Guide Example: If you wish to define a name which incl udes spaces, you must enclose the entire name in quotation marks, for example “new york”. session User level: user, privileged, supervisor Use the session comm and to open a session with a specific entity within a switc[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 59 Example: set allowed managers User level: privileged, supervisor. Use the set allowed managers command to enables or disable the Allowed Managers feature. When this feature is enabled, only those s tations whose IP addresses are listed in the Allowed Managers table can a[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 60 Avaya P330-ML Reference Guide Example: set arp-aging-interval User level: privileged, supervisor. Use th e set arp-aging interval command to set the ARP table aging interval for entries in the agent Layer 2 ARP table. The entry is deleted at the end of every aging interval . The default value is 10 mi[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 61 set autopartition User level: privileged, supervisor. L This command is not relevant to P330-M L-ML switches. It appears in the P330- ML-ML CLI for controlling autopartition of other P330-ML switches in the stack. Use the set autopartition command to enable or disable au[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 62 Avaya P330-ML Reference Guide set cascading User level: privileged, supervisor. Use the set cascading command to control the generation of fault-traps for unconnected cascading links. This command is useful when cascad ing cables are not connected intentionally, and the refore no fault-traps are desir[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 63 The syntax for this command is: P330-N> set dot1x max-req <count> Example: set dot1x quiet-period User level: supervisor Use the set dot1x quiet-period command to set the minim al time between authentication attempts. The syntax for this command is: set dot1x qu[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 64 Avaya P330-ML Reference Guide User level: superviso r Use the set dot1x server-timeout command to set the server retransmissi on timeout period for all ports. This is the maximum time that the port will wait for a reply from the Authentication Server. The syntax for this command is: set dot1x server-t[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 65 set dot1x system-auth-cont rol enable User level: supervisor Use the set dot1x system-auth-control enable command to globally enable the PBNAC (802.1x) feature. The syntax for this command is: set dot1x system-auth-control enable Examples: • When a RADIUS server is def[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 66 Avaya P330-ML Reference Guide Example: set inband vlan User level: privileged, supervisor. Use the set inband vlan command to set the inband management VLAN. The syntax for this command is: set inband vlan <value> Example: set intelligent -multicast User level: privileged, supervisor. Use the se[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 67 The syntax for this command is: set intelligent-multicast client-port-pruning time <seconds> Example: set intelligent- multicast grou p-filtering-del ay time User level: privileged, supervisor. Use the set intelligent-multicast group-filtering delay time command to[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 68 Avaya P330-ML Reference Guide Example: set interface i nband User level: privileged, supervisor. Use the set interface inband command to configure the Management inband interface on the Master agent in the stack. The syntax for this command is: set interface inband <vlan> <ip_addr> <net[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 69 The syntax for this command is: set interface ppp <ip_addr> <net-mask> Example: set interface pp p enable/enable-a lways/disable/off /reset User level: privileged, supervisor. Use the set interface ppp command to enter modem mode, enter terminal mode, disconn[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 70 Avaya P330-ML Reference Guide Example: Example: set intermo dule port red undancy User level: privileged, supervisor. Use the set intermodule port redu ndancy command to define the stack’s unique intermodule redundancy scheme. Th e defined scheme can be cleared using the set intermodule port redunda[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 71 set intermodule port redundancy off Use the set intermodule port redundancy off command to clear the intermodule port redundancy scheme. The syntax for this command is: set intermodule port redundancy off Example: set internal buffering User level: privileged, supervisor[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 72 Avaya P330-ML Reference Guide set ip route User level: privileged, supervisor. Use the set ip route command to add a route to the IP routing table. You can configure from 1 to 10 default static gateways for a P330-ML switch. The syntax for this command is: set ip route <destination> <gateway&[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 73 The syntax for this command is: set license [module] [license] [feature name] Example: set logging file condition User level: privileged, supervisor. Use the set logging file condition command to define a filter rule for logging messag es to the logging file. The syntax [...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 74 Avaya P330-ML Reference Guide application The application from which log ging messages are logged to the logging file . Possible values are: • BOOT •S Y S T E M •R O U T E R •C O N F I G •F I L E S Y S •F A N •S U P P L Y •S E C U R I T Y •C A S C A D E • QOS •S W I T C H F A B R[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 75 Example: set logging file disable User level: privileged, supervisor. Use the set logging file disable command to disable logging message s to a logging file . The syntax for this command is: set logging file disable Example: set logging file enable User level: privilege[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 76 Avaya P330-ML Reference Guide Example: set logging serve r access-level User level: privileged, supervisor. Use the set logging server access -level command to define the access level associated with Syslog server s i nk. The user cannot specify an access level higher than the level assigned to him. L[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 77 The syntax for this command is: set logging server condition { all | <application> } { none | <severity> } <ip-address> all A keyword signifying that the specified se verity threshold applies to all applications. application The appl ication to which th[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 78 Avaya P330-ML Reference Guide Example: set logging serve r disable User level: privileged, supervisor. Use the set logging server disabl e command to disabl e logging messages to a Syslog server. L You need to define a logging server using the set logging server command before you can disable the serv[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 79 Example: set logging serv er facility User level: privileged, supervisor. Use the set logging server facility command to update the server fa cility used for sending messages to Syslog server. Facility settings are done on per Syslog server. L You need to define a loggin[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 80 Avaya P330-ML Reference Guide Example: set logging session condition User level: privileged, supervisor. Use the set logging session condi tion command to define a filter rule for logging messages during the current session. The syntax for this command is: set logging session condition { all | <app[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 81 Example: set logging session disable User level: privileged, supervisor. Use the set logging session disable command to disable logging messages in the current CLI sessi on. The syntax for this command is: set logging session disable Example: set logging session enable U[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 82 Avaya P330-ML Reference Guide Example: set logout User level: privileged, supervisor. Use the set logout command to set the time in minutes before the system automaticall y disconnects an idle se ssion. The syntax for this command is: set logout [timeout in minutes] Examples: • To set the time until[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 83 The syntax for this command is: Set mac-aging <status> Examples: set mac-aging-time User level: privileged, supervisor. L This command is available on the P330-ML-ML switches only. Use the set mac-aging-time command to set the MAC aging time in minutes. This is the[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 84 Avaya P330-ML Reference Guide <module>/<port> {no-flowcontrol|asym-tx-only|sym-only|sym-and- asym-rx} Example: set port channe l User level: privileged, supervisor. Use the set port channel command to enable or disable a Link A ggregation Group (LAG) interface on the switch. LAG creati on [...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 85 The syntax for this command is: set port channel [<port_list>] [<value>] [<name>] L If you wish to define a name which include s spaces, you must enclose the entire name in quotation marks, for example “new york”. Example: set port classification Us[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 86 Avaya P330-ML Reference Guide The syntax for this command is: set port disable <mod_num>/<port_num> Example: set port dot1x initialize User level: superviso r Use the set port dot1x initialize command to initialize port dot1x. The syntax for this command is: set port dot1x initialize <m[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 87 The syntax for this command is: set port dot1x max-req <module/port> <count> Example: set port dot1x p ort-control User level: supervisor Use the set port dot1x port-control command to set the dot1x pa rameter per port. The syntax for this command is: set por[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 88 Avaya P330-ML Reference Guide The syntax for this command is: set port dot1x quiet-period <module/port> <seconds> Example: set port dot1x re-authentic ate User level: superviso r Use the set port dot1x re-authent icate command to set the port to re- authenticate. The syntax for this comman[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 89 Example: set port dot1x re-authperiod User level: supervisor Use the set port dot1x re-authperiod command to set the the idle time between re-authentication attempts before the session i s terminated. The syntax for this command is: set port dot1x re-authperiod <modul[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 90 Avaya P330-ML Reference Guide set port dot1x supp-timeout User level: superviso r Use the set port dot1x supp-timeout command to set the time for the port to wait for a reply from the Authentication Server before the se ssion is terminated. The syntax for this command is: set port dot1x supp-timeout &[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 91 The duplex status of a port in auto-neg o tiation mode is determined by auto - negotiation. An error message is generate d if you attempt to set the transmission type of auto negotiation Fast Ethernet ports to half- or full-duplex mode. L P332G-ML and P332GT-ML ports and[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 92 Avaya P330-ML Reference Guide Examples: set port enable User level: privileged, supervisor. Use the set port enable command to enable a port or a range of port s. The syntax for this command is: set port enable [mod_num/port_num] Example: set port flowco ntrol User level: privileged, supervisor. Use t[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 93 | on | proprietary} Example: set port level User level: privileged, supervisor. Use the set port level command to set the priority level of a port or range of ports on the switching bus. Packets travelin g through a port set at normal priority should be serve d only afte[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 94 Avaya P330-ML Reference Guide Example: set port mirr or User level: privileged, supervisor. Use the set port mirror command t o define a port mirroring pair in the stack. Note: Ensure that the VLAN binding paramete rs are identical on the source and destination ports. The syntax for this command is: s[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 95 set port name User level: privileged, supervisor. Use the set port name command to configure a name for a port. If you do not specify a name, the port name remains blank. The syntax for this command is: set port name <module>/<port> [<name>] Example: L [...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 96 Avaya P330-ML Reference Guide The syntax for this command is: set port negotiation <module>/<port> {enable|disable} Example: To disable autonegot iation on port 1, module 4 : set port point- to-point adm in status User level: privileged, supervisor. Use the set port point-to-point admin st[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 97 set port powerline User level: privileged, supervisor. L This command applies to P333T-P WR swit ches only and is used by P330- ML-ML switches to control P 333T-PWR modules in the stack. Use the set port powerinline command to enable or disable the load detection process[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 98 Avaya P330-ML Reference Guide Example: set port redun dancy User level: privileged, supervisor. Use the set port redundancy comm and to globally enables or disable the port redundancy pairs you have defined. Usin g this command will not delete from NVRAM the existing redundanc y entries. The syntax fo[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 99 Example: L If you wish to define a name which include s spaces, you must enclose the entire name in quotation marks, for example “new york”. set port redundancy-intervals User level: privileged, supervisor. Use the set port redundancy-intervals comma nd to configurs [...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 100 Avaya P330-ML Reference Guide set port sec urity User level: superviso r Use the set port security command to enable MAC security on a port or a range of ports at th e module level. The port security is activate d only after you enable the secutity mode at the sta ck level using the set security mode[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 101 set port spantree di sable User level: privileged, supervisor. Use the set port spantree disable command to disable the spanning tree mode for specif ic switch ports. The syntax for this command is: set port spantree disable [module/port] Example: set port spantree en a[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 102 Avaya P330-ML Reference Guide The syntax for this command is: set port spantree force-protocol-migration <module/port> Example: set port span tree priority User level: privileged, supervisor. Use the set port spantree command to set the Spanning Tree priority level of a port. This value defines[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 103 L This command is can not be executed for P332G-ML and P332GT-ML ports and P334T-ML ports 51, 52 (Gigabit SFP ports) . An error message is generated if you attempt to perform the set port speed command for these ports that can only work at 1000Mbps speed. L Copper ports[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 104 Avaya P330-ML Reference Guide Example: set port trap User level: privileged, supervisor. Use the set port trap command to enable or disa ble generi c SNMP uplink or downlink traps from a port. The syntax for this command is: set port trap <module>/<port> {enable|disable} Example: set port[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 105 Example: To set VLAN 850 to include po rts 4 through 7 on module 3. set port vlan-binding-mode User level: privileged, supervisor. Use the set port vlan-binding-mode command to define the binding method used by ports. The syntax for this command is: set port vlan-bindin[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 106 Avaya P330-ML Reference Guide set powerinli ne external power User level: privileged, supervisor. L This command applies to P333T-PWR switches only and is used by P330- ML-ML switches to control P333T-PWR modules in the stack. Use the set powe rinline external power command to set the maximum power a[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 107 set ppp baud-rate User level: privileged, supervisor. Defines the baud rate used in PPP sessions. L The peer baud rate must be set at the same value as the host. The syntax for this command is: set ppp baud-rate <9600|19200|38400> Example: set ppp chap-secret User[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 108 Avaya P330-ML Reference Guide Example: set psu type User level: privileged, supervisor. Use the set psu type command to set the main powe r supply type (AC/DC) of the module. L This command is not applicable to P3 30-ML-ML switches, which determine the PSU type automatica lly. This command is used to[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 109 set queuing scheme User level: privileged, supervisor. L This command is applicable to P330-ML-ML switches only. Use the set queuing scheme command to set the queuing scheme to either strict or weighted round robin and to set the weights. The syntax for this command is:[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 110 Avaya P330-ML Reference Guide The syntax for this command is: set radius authentication {enable|disable} Example: set radius authenti cation retry-number User level: privileged, supervisor. Sets the number of times an access reques t is sent when there is no response. The syntax for this command is: [...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 111 set radius authenticatio n secret User level: supervisor Use the set radius authentication secret command to enable secret authentication for the P330-ML unit. The syntax for this command is: set radius authentication secret <string> string t ext pa ssword Example[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 112 Avaya P330-ML Reference Guide The syntax for this command is: set radius authentication udp-port <number> Example: P330-1(super)# set radius authentication udp-port 300[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 113 set secure mac User level: privileged, supervisor. Use the set secure mac command to a dd a unicast MAC address into the CAM table of a secured port. The syntax for this command is: set secure mac <mac-address> port <mod-num> / <port-num> Example: set [...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 114 Avaya P330-ML Reference Guide The syntax for this command is: set security violaton action { restrict | restrict-and-notify } Example: set snmp community User level: privileged, supervisor. Use the s et snmp community comman d to set or modify the switch’s SNMP community strings. The syntax for thi[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 115 Example: set snmp timeout User level: privileged, supervisor. Use the set snmp timeout command to set the SNMP timeout in seconds. This command is only used for access us ing the P330-ML Embedded We b Manager. The syntax for this command is: set snmp timeout <number&[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 116 Avaya P330-ML Reference Guide Example: To enable SNMP ConfigChange traps to a specific manager: Example: To enable all traps to a specific manager: Example: To disable SNMP config traps to a specific manager: Example: To add an entry in the SNMP trap receiver table with default: set snmp trap au th U[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 117 set spantree default-path-cost User level: privileged, supervisor. Use the set spantree default-path-cost command to set the version of the spanning tree default path costs that are to be used by this bridge. The syntax for this command is: set spantree default-path-cos[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 118 Avaya P330-ML Reference Guide The syntax for this command is: set spantree enable Example: set spantree forward-delay User level: privileged, supervisor. Use the set spantree forward-dela y command to set the bridge forward delay time parameter. The syntax for this command is: set spantree forward-de[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 119 set spantree max-age User level: privileged, supervisor. Use the set spantree max-age command to set the bridge spanning tree max age param eter. The syntax for this command is: set spantree max-age <seconds> Example: set spantree priority User level: privileged, [...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 120 Avaya P330-ML Reference Guide set spantree tx-hold-count User level: privileged, supervisor. Use the set spantree tx-hold-coun t command to limit the maximum number of BPDUs transmitte d during a hello-time period. The syntax for this command is: set spantree tx-hold-count <rate> Example: set s[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 121 set system contact User level: privileged, supervisor. Use the set system contact command to set the mib2 system contact MIB variable. The syntax for this command is: set system contact [string] Example: set system location User level: privileged, supervisor. Use the se[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 122 Avaya P330-ML Reference Guide set system name User level: privileged, supervisor. Use the set system name command to set the mib2 system name MIB variable. The syntax for this command is: set system name [string] Example: L If you wish to enter a name which includes spaces , you must enclose the enti[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 123 L This command can only be run from the console port on the device. The syntax for this command is: set terminal recovery password enable Example: set time client User level: privileged, supervisor. Use the set time client command to enable or disable the pe riodic netw[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 124 Avaya P330-ML Reference Guide Example: set time server User level: privileged, supervisor. Use the set time server command to set the TIME server ad dress. The syntax for this command is: set time server <ip address> Example: set timezone User level: privileged, supervisor. Use the set timezone[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 125 set trunk User level: privileged, supervisor. Use the set trunk command to configure the VLAN tagging mode of a port. set trunk <module/port> {off|dot1q} Example: set utilization cpu User level: privileged, supervisor. Use the set utilization cpu command to enable[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 126 Avaya P330-ML Reference Guide set vlan User level: privileged, supervisor. Use the set vlan command to configure VLANs. The syntax for this command is: set vlan <vlan-id> [name <vlan-name>] Example: L If you wish to define a name which includes spaces, you must enclose the entire name in [...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 127 set welcome message User level: privileged, supervisor. Use the set welcome message command to set a welcome message to appear after a reboot or after op ening a new session (see session command) in the stack. The syntax for this command is: set welcome message [string][...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 128 Avaya P330-ML Reference Guide show allowed mana gers status User level: user, privileged, supervisor Use the show allowed managers status command to display the activation status of the Allowed Managers f eature. The syntax for this command is: show allowed managers status Example: show allowed mana [...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 129 Example: show arp-aging-i nterval User level: privileged, supervisor. Use the show arp-aging-interval command to display the ARP table aging interval for table entries. The syntax for this command is: show arp-aging-interval Example: show arp-tx-interval User level: pri[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 130 Avaya P330-ML Reference Guide The syntax for this command is: show arp-tx-interval Example: show autopartit ion User level: privileged, supervisor. Use the show autopartition command to display the automatic partition. L Autopartition for the P330-ML-M L switches will always have the value disabled .[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 131 show boot bank User level: privileged, supervisor. L This command is not supported by the P333R and P333R-LB switches. Use the show boot bank command to display the software bank from which the switch will boot at the next boot process. You must issue this command separ[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 132 Avaya P330-ML Reference Guide Example: (by M odule/Port) show cam mac User level: user, privileged, supervisor Use the show cam mac command to display the module and port number where a specific MAC address was learned. L MACs associated with LAGs appear under th e LAG ID, not under the LAG port. The[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 133 The syntax for this command is: show cam vlan <vlan-number> Example: show cascading faul t-monitoring User level: user, privileged, supervisor Use the show cascading fault-monitoring command to display the status of the fault trap sending mode for cascading link s[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 134 Avaya P330-ML Reference Guide show copy status User level: user, privileged, supervisor Use the show copy status command to show the status of the local configuration copy operation. The syntax for this command is: show copy status Example: show dev log file User level: privileged, supervisor. L This[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 135 show device-mode User level: user, privileged, supervisor Use the show device-mode command to show the current P330-ML-ML or P333R operating mode. Possible modes are Router, or Layer 2. L This command is not available to the P333T, P334T, P332MF and P333T- PWR switches [...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 136 Avaya P330-ML Reference Guide The syntax for this command is: show download status [slot] Example: show erase st atus User level: user, privileged, supervisor Use the show erase status comman d to view the status of the erase configuration operation. The syntax for this command is: show erase status [...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 137 show intellige nt-multicast User level: user, privileged, supervisor Use the show intelligent-multicast command to display the inte lligent multicast configuration. The syntax for this command is: show intelligent-multicast Example: show intelligent-mul ticast hardware-[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 138 Avaya P330-ML Reference Guide show interface User level: user, privileged, supervisor Use the show interface command to display information on network interfaces. The syntax for this command is: show interface Example: show intermodul e port redund ancy User level: user, privileged, supervisor Use th[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 139 The syntax for this command is: show internal buffering [<mod_num>] Example: show ip access-g roup User level: privileged, supervisor. Use the show ip access-group command to display the acti ve policy-list number. L This command applies to the P334T-ML only when [...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 140 Avaya P330-ML Reference Guide The syntax for this command is: show ip access-list-details <policy-list-number> Example: show ip access-list-dscp User level: user, privileged, supervisor L This command applies to the P334T-ML only when it is in device mode "Layer2". Use th e show ip ac[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 141 Example: show ip access lists User level: user, privileged, supervisor Use the show ip access lists command to display all the current policy lists. L This command applies to the P334T-ML only , when it is in device mode "Layer2". The syntax for this command i[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 142 Avaya P330-ML Reference Guide show ip access-list-summary User level: user, privileged, supervisor L This command applies to the P334T-ML only when it is in device mode "Layer2". Use the show ip acce ss-list-summary command to display a summary of policy lists. The syntax for this command i[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 143 show ip ssh User level: supervisor Use the show ip ssh command to display active SSH connections. The syntax for this command is: show ip ssh Example: show l2-module-c onfig User level: privileged, supervisor. Use the show l2-module-config command to display Layer 2 mod[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 144 Avaya P330-ML Reference Guide Example: P330-N> show l2-module-config Please be patient. Gathering and displaying the information might take a while. P330-ML-N(super)# !# !# Upload time: Unavailable Unavailable !# System description: Avaya Inc. - P330-ML !# Master position: 2 !# !# Module #: 2 !# M[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 145 .... .... set port negotiation 2/11 disable set port duplex 2/11 half set port disable 2/15 set port negotiation 2/31 disable set trunk 2/40 dot1q set trunk 2/44 dot1q set port vlan 500 2/44 set trunk 2/51 dot1q set port dot1x port-control 2/2 force-authorize set port d[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 146 Avaya P330-ML Reference Guide show l2-stack-config User level: privileged, supervisor. Use the show l2-stack-config command to display Layer 2 stack configuration. L If this command is to be implemented on a switch other than the stack master, a session should be opened to the relevant switch. The sy[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 147 Example:[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 148 Avaya P330-ML Reference Guide P330-N> show l2-stack-config P330-ML-N(super)# !# !# Upload time: Unavailable Unavailable !# System description: Avaya Inc. - P330-ML !# IP address, netmask: 149.49.138.157 255.255.255.0 !# Master position: 2 !# Number of modules: 2 !# set spantree priority 4096 set a[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 149 show license User level: privileged, supervisor. Use the show license command to display the current licenses installed on the stack. ... set time client disable set ip route 0.0.0.0 149.49.138.1 set logout 0 set vlan 2 name V2 set vlan 3 name V3 set port static-vlan 1/[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 150 Avaya P330-ML Reference Guide The syntax for this command is: show license Example: show log User level: privileged, supervisor. Use the show log command to display an encr ypted device’s reset log. L This command is for Avaya technical support use. The syntax for this command is: show log [mod_num[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 151 show logging f ile condition User level: user, privileged, supervisor Use the show logging file condition command to display the condition and filtering of the log file. The syntax for this command is: show logging file condition Example: P330-N> show logging file co[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 152 Avaya P330-ML Reference Guide show logging fil e content User level: user, privileged, supervisor Use the show logging file content command to display the contents of the log file. The syntax for this command is: show logging file content [<severity>] [{all|<application>}] [<number>[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 153 Example: application The appl ication to which the filter applies. Possible values are: • BOOT •S Y S T E M •R O U T E R •C O N F I G • FILESYS •F A N • SUPPL Y •S E C U R I T Y •C A S C A D E • QOS •S W I T C H F A B R I C •L A G •V L A N •S[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 154 Avaya P330-ML Reference Guide show logging server conditi on User level: user, privileged, supervisor Use the show logging server condi tion command to display the condition and filteri ng of logging to th e Syslog server. The syntax for this command is: show logging server condition <ip-address&g[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 155 show logging se ssion condition User level: user, privileged, supervisor Use the show logging session condition command to display the condition and filtering of l ogging in the current CLI session. The syntax for this command is: show logging session condition Example:[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 156 Avaya P330-ML Reference Guide Use the show mac-aging command to display the current status of the MAC aging function. The syntax for this command is: show mac-aging Example: show mac-aging-time User level: user, privileged, supervisor Use the show mac-aging-time command to dis play the MAC aging time[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 157 Example: Output Fields show module-id entity User level: user, privileged, supervisor Use the show module-identity command to display the switch identity required for acquiri ng a license. The syntax for this command is: show module-identity [module] Example: P330-N>[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 158 Avaya P330-ML Reference Guide show port User level: user, privileged, supervisor Use the show port command to display port status. The syntax for this command is: show port [<mod_num>[/port_num]] Example: to display the status for port 4 on switch 3 Show Port Output F ields mod_num (Optional) N[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 159 show port auto-negot iation-flowcontrol-advertisemen t User level: privileged, supervisor. Use the show port auto-negotiation-flowcontrol-advertisement command to display the flowcontrol adve rtisement for a Gigabit port used to perform auto-negotiation. The syntax for [...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 160 Avaya P330-ML Reference Guide Example: P330-N> show port channel Port Channel Status Channel Name Channel Id ------ --------------- ---------------- ---------------- 1/1 on MEIR 1/101 1/2 on MEIR 1/101 1/3 off 1/4 off 1/5 on my-channel 1/102 1/6 on my-channel 1/102 1/7 off 1/8 on my-channel 1/102 [...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 161 show port classificatio n User level: user, privileged, supervisor Use the show port classification command to display a port’s classification. The syntax for this command is: show port classification [module/[port]] Example: module Number of the switch. If you do not[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 162 Avaya P330-ML Reference Guide show port dot1x User level: user, privileged, supervisor Use the show port dot1x command to display all the confi gurable values associated with the authenticator po rt access entity (PAE) and backend authenticator. The syntax for this command is: show dot1x [mod]/[port][...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 163 BEnd Stat The current state od the Backend Authenticati on state machine. Possible stat es include: •R e q u e s t •R e s p o n s e • Success •F a i l •T i m e o u t •I d l e •I n i t Port Control Port control type. Valid valu es include: •f o r c e - a [...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 164 Avaya P330-ML Reference Guide show port dot1 x statistics User level: user, privileged, supervisor Use th e show port dot1x statistics command to display all the port do t1x statistics. The syntax for this command is: show dot1x statistics [mod]/[port] Example: Max Req The maximum number of times a r[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 165 show port edge state User level: user, privileged, supervisor Use the show port edge state command to show a port’s edge admin and operational RSTP state. L A port can be set to admin state of edge port, but if a BPDU is received on this port the oper state is changed[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 166 Avaya P330-ML Reference Guide Output Fields Field Description Port Module and port number Send- Flowcontrol- Admin Send flow-control admini stration. Possible settings: • ON indicates that the local port is allowed to send flow control frames to the far end. • OFF indica tes that the local port i[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 167 show port mirror User level: user, privileged, supervisor Use the show port mirror command to di splay mirroring information for the stack. The syntax for this command is: show port mirror Example: show port point-to-point st atus User level: user, privileged, superviso[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 168 Avaya P330-ML Reference Guide show port redundan cy User level: user, privileged, supervisor Use the show port redundancy command to di splay information about the port redundancy schemes defined for the switch. The “status” column displays which of the two redundancy member ports is enabled curr[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 169 show port trap User level: user, privileged, supervisor Use the show port trap command to display information on SNMP generic link up/down traps sent for a specific port. The syntax for this command is: show port trap [<module>[/<port>]] Example: show port v[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 170 Avaya P330-ML Reference Guide Example: Show powerinline User level: user, privileged, supervisor L This command applies to P333T-PWR switches only and is used by P330- ML-ML switches to control P333T-PWR modules in the stack. Use the show powerinline c ommand to display the current status of the PD i[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 171 Example: Example: show powerinline i mage version User level: user, privileged, supervisor L This command applies to P333T-P WR swit ches only and is used by P330- ML-ML switches to control P 333T-PWR modules in the stack. Use the show powerinline image version command [...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 172 Avaya P330-ML Reference Guide image version of P333T-PWR switches in the stack or a specif ic switch. The syntax of this command is: show powerinline image version [<module-number>] If you do not specify a number , then the software version for all the P333T-PWR switches is shown. Example: Exam[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 173 show ppp baud-rate User level: user, privileged, supervisor Use the show ppp baud-rate command to display the ppp baud-rate. The syntax for this command is: show ppp baud-rate Example: show ppp configurati on User level: user, privileged, supervisor Use the show ppp con[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 174 Avaya P330-ML Reference Guide Example: show ppp session User level: user, privileged, supervisor Use the show ppp session command t o display PPP para meters and statistics of an active PPP session. The syntax for this command is: show ppp session Example: show protocol User level: user, privileged, [...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 175 show queuing scheme User level: user, privileged, supervisor L This command is available on P330-ML-ML switches only Use the show queuing scheme command to display the current queuing scheme settings. L If this command is to be implemented on a P330-ML-ML switch other t[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 176 Avaya P330-ML Reference Guide show rmon alarm User level: user, privileged, supervisor Use the show rmon alarm command to dis play the parameters set for a specif ic alarm entry that was set using the rmon alarm command on or using the P330-ML Manager. The syntax for this command is: show rmon alarm [...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 177 show rmon event User level: user, privileged, supervisor Use the show rmon event command to show the parameters of an Event entry defined by the rmon event command or using the P330-ML Manager. The syntax for this command is: show rmon event [<Event Index>] Exampl[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 178 Avaya P330-ML Reference Guide Example: show rmon statisti cs User level: user, privileged, supervisor Use the show rmon statistics command to show the Received Packet RMON statistics counters for a certain interfac e number according to th e MIB-2 interface table numb ering s cheme. The syntax for th[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 179 Example: show secure curre nt User level: user, privileged, supervisor Use the show secure current command to list the IP addresses of managers currently connected to the switch. The syntax for this command is: show secure current Example: show secure mac User level: us[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 180 Avaya P330-ML Reference Guide Example: show security mode User level: user, privileged, supervisor Use the show security mode command to display the status of the MAC security feature. The syntax for this command is: show security mode Example: show snmp User level: user, privileged, supervisor Use t[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 181 Example: P330-N> show snmp Authentication trap enabled Community-Access Community-String ---------------- ---------------- read-only public read-write public trap meir Trap-Rec-Address Status Traps Configured ---------------- -------- ---------------- 135.64.100.73 E[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 182 Avaya P330-ML Reference Guide SNMP-Rec-Address Model Level Notification Trap/Inform User name ---------------- ----- ------- --------------- ----------- ------------------ 135.64.100.73 v1 noauth config trap WriteCommN UDP port: 162 sw-redundancy temperature cam-Change supply l3-fault link-down-fault[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 183 Output fields: show snmp group User level: supervisor Use then show snmp group command to display SNMP groups. The syntax for this command is: show snmp group [<group-name>] ] Field Description EngineId The SNMP engine ID. EngineBoots The number of times the SNMP [...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 184 Avaya P330-ML Reference Guide Example: P330-N> show snmp group Group Name: initial Security Model: v3 Security Level: noauth Read View: iso Write View: iso Notify View: iso Status: active Group Name: ReadCommG Security Model: v1 Security Level: noauth Read View: snmpv1View Write View: Notify View:[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 185 show snmp retries User level: user, privileged, supervisor Use the show snmp retries command to display the number of retries initiated by the P330-ML Embedded Web Manager when it tries to send SNMP messages to the device. The syntax for this command is: show snmp retri[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 186 Avaya P330-ML Reference Guide information for a specific user. The syntax for this command is: show snmp user [<user>] Example: show snmp userToGroup User level: superviso r Use then show snmp userToGroup command to d isplay the assignment of users to SNMPv3 groups. The syntax for this command [...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 187 Example: show snmp view User level: supervisor Use then show snmp view command to display SNMP view config urations. If no view name is provided, the configuration of all SNMP views is displayed . The syntax for this command is: show snmp view [<viewname>] P330-N&[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 188 Avaya P330-ML Reference Guide Example: P330-N> show snmp view snmpv1View View Name: snmpv1View Subtree Oid: 1 Subtree Mask: View Type: include Storage Type: nonVolatile Status: active View Name: snmpv1View Subtree Oid: 1.3.6.1.6 Subtree Mask: View Type: exclude Storage Type: nonVolatile Status: ac[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 189 Output fields: show spantree User level: user, privileged, supervisor Use then show spantree command to display spanning -tree information. The syntax for this command is: show spantree [<mod_num>[/<port_num>]] Field Description View Name The name of the vie[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 190 Avaya P330-ML Reference Guide Example: P330-N> show spantree Spanning tree state is enabled Designated Root: 00-40-0d-8c-88-ff Designated Root Priority: 32768 Designated Root Cost: 100 Designated Root Port: 1/7 Root Max Age: 20 Hello Time: 2 Root Forward Delay: 15 Bridge ID MAC ADDR: 00-40-0d-b9-8[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 191 Output fields: Field Description Spanning tree Status of whether Spa nning-Tree Protocol is enabled or disabled Designated Root MAC address of the designated spanning-tree root bridge Designated Root Priority Priority of the designated root bridge Designated Root Cost T[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 192 Avaya P330-ML Reference Guide show system User level: user, privileged, supervisor Use the show system command to display the up time, system name, location, and contact pe rson. The syntax for this command is: show system Example: Spanning Tree Default Path Costs The version of the Spanning Tree def[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 193 show tftp download software status User level: user, privileged, supervisor Use the show tftp download software status commands to display the status of the current TFTP Device Manager S/W (Embedded Web) download process into the device. The syntax for this command is: [...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 194 Avaya P330-ML Reference Guide Example: show time parameters User level: user, privileged, supervisor Use the show time parameters command to display the time status and parameters. The syntax for this command is: show time parameters Example: show timeout User level: user, privileged, supervisor Use [...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 195 The syntax for this command is: show timezone Example: show trunk User level: user, privileged, supervisor Use the show trunk command to display VLAN tagging information for the switch or a specified module or port. The syntax for this command is: show trunk [<mod_nu[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 196 Avaya P330-ML Reference Guide Example: Output Fields: show upload statu s User level: user, privileged, supervisor Use the show upload status comma nds to display the status of the current configuration file copy process from the device. P330-N> show trunk 4/1-2 P330-ML-1(super)# show trunk 1/42-4[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 197 The syntax for this command is: show upload status [<mod_num>] Example: show username User level: supervisor Use the show username command to display the local user accounts. The syntax for this command is: show username Example: show utilizatio n User level: priv[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 198 Avaya P330-ML Reference Guide The syntax for this comman d is: show utilization <module-number> Example: module-number The module f or which to display utilization statistics. If no module is specified, utilization statistics for all modul es is displayed. P330-1(super)# show utilization Mod CP[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 199 show vlan User level: user, privileged, supervisor Use the show vlan command to display the VLANs conf igured in the stack or switch or the ports bound to a specified VLAN. The syntax for this command is: show vlan { <vlan-number> | <vlan-name> } Examples: v[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 200 Avaya P330-ML Reference Guide Output Fields: show web aux-file s-url User level: user, privileged, supervisor Displays the URL/directory from wh ere the switch can access the Device Manager auxiliary files (for example help fi les). The syntax for this command is: show web aux-files-url Example: snmp[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 201 snmp-server enable User level: supervisor Use the snmp-server command to enable SNMP Access to the switch. The syntax for this command is: snmp-server enable [volatile] Example: snmp-server enable notif ications User level: supervisor Use the snmp-server enable notifica[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 202 Avaya P330-ML Reference Guide The syntax for this command is: snmp-server engineID <engineID> Example: snmp-server group User level: superviso r Use the snmp-server group command to configure SNMPv3 groups. The syntax for this command is: snmp-server group <groupname> [ v1 | v2c | v3 { no[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 203 Example: snmp-server host User level: supervisor Use the snmp-server host command to specify the recipient of the notification operations and filter traps to that s tation. This command provide s maximum flexibility. For each notification grou p you can define one of fo[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 204 Avaya P330-ML Reference Guide Example: snmp-server informs User level: superviso r Use the snmp-server informs command to configure inform parameters. udp-port (Optional) Keyword that specifies that a specific UDP port on the target host should be used when send ing notifications to the host. The def[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 205 The syntax for this command is: snmp-server informs retries <retries-num> timeout <seconds> Example: snmp-server remot e-user User level: supervisor Use the snmp-server remote user command to configure a remote-user as a target for SNMP notifications. The sy[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 206 Avaya P330-ML Reference Guide Example: snmp-server user User level: superviso r Use the snmp-server user command to configure a new SNMP user. The syntax for this command is: snmp-server user <username> <groupname> { v1 | v2c | v3 } [ auth { md5 | sha } <auth-password> [ priv des56 [...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 207 Example: snmp-server view User level: supervisor Use the snmp-server view command to configure an SNMP MIB view. Use multiple iterations of the command to add or remove OIDs from the view. The syntax for this command is: snmp-server view <view-name> <oid-tree&g[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 208 Avaya P330-ML Reference Guide L The stack is reset once the command has been executed. L You should not load the stack wi th traffic during this test. L Please follow the ins truction shown on th e CLI screen, during the various stages of this test. The syntax for this comman d is: stack health Examp[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 209 The syntax for this command is: telnet <ip-address> [<port-number>] Example: terminal User level: user, privileged, supervisor Use the terminal width and terminal length commands to set the width and length of the terminal display in characters. The syntax f[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 210 Avaya P330-ML Reference Guide Example: L If you wish to define a name which includes spaces, you must enclose the entire name in quotation marks, for example “new york”. validate-group User level: privileged, supervisor. L This command applies to the P334T-ML only when it is in device mode "[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands Avaya P330-ML Reference Guid e 211 Example: L The validation process may take some time to complete. P330-N# validate-group 101 List 101 is valid-in-progress P330-N# validate-group 101 List 101 is valid[...]

Chapter 2 Avaya P330-ML Layer 2 CLI Commands 212 Avaya P330-ML Reference Guide[...]

Avaya P330-ML Reference Guid e 211 Chapter 3 Avaya P330-ML Layer 3 CLI Commands This chapter provides all the Layer 3 CL I (Command Line Interface) commands, parameters, and their default values. How the Layer 3 CLI is Organized The commands that make up the Layer 3 CLI are organized alphabetically and according to context. Router Configuratio n Co[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands 212 Avaya P330-ML Reference Guide General Commands arp User level: privileged, supervisor. L If you are at the “pri vileged” level, you can only access thi s command in Configure mode. Type configure at the command prompt to enter configure mode. Use the arp command to a dd a permanent entry to the A[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands Avaya P330-ML Reference Guid e 213 The syntax for this command is: [no] arp timeout <seconds> Example: To set the arp timeout to one hour: To restore the def ault arp timeout: clear arp-cache User level: privileged, supervisor. L If you are at the ”privileg ed” level, you can only access this c[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands 214 Avaya P330-ML Reference Guide clear fragmen t User level: privileged, supervisor. Use the clear fragment command to restore fragment ac tion database def aults and free all wai ting fragments. The syntax for this command is: clear fragment Example: clear ip route User level: privileged, supervisor. U[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands Avaya P330-ML Reference Guid e 215 clear ip traffi c User level: privileged, supervisor. L This command does not apply to th e P333R-LB. Use the clear ip traffic command to clear the ip traffic statistics counters. The syntax for this command is: clear ip traffic Example: clear screen User level: user, p[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands 216 Avaya P330-ML Reference Guide configure User level: privileged, supervisor. Use the configure command to ente r configure mode. The syntax for this command is: configure Example: copy module-config scp Use the copy module-config scp command to upload the switch-level parameters from the current NVRAM[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands Avaya P330-ML Reference Guid e 217 copy module-confi g tftp Use the copy module-config tftp command to upload the switch-level parameters from the current NVRAM r unning configurat ion into a file via TFTP. The syntax for this command is: copy module-config tftp <filename> <ip> <mod_num>[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands 218 Avaya P330-ML Reference Guide Example: copy running-confi g startup-config User level: privileged, supervisor. Use the copy running-config startup-config command to save the policy and router config urations to the star tup configuration file in the NVRAM. The syntax for this command is: copy running[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands Avaya P330-ML Reference Guid e 219 Example: Example: (for Unix): copy scp modul e-config User level: privileged, supervisor. Use the copy scp module-config command to download a module configuration to the device via SCP. L Only parameters that differ from the fa ctory default settings for the s witch ar[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands 220 Avaya P330-ML Reference Guide copy scp startup-config User level: privileged, supervisor. Use the copy scp startup-config command to download a startup configuration to the device via SCP. L Only parameters that differ from the factory default settings for the switch are included in the configuration[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands Avaya P330-ML Reference Guid e 221 Example: copy startup-conf ig tftp User level: privileged, supervisor. Use the copy startup-config tftp command to upload the policy and router startup configurations to a TFTP server. The syntax for this command is: copy startup-config tftp <filename> <ip> [...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands 222 Avaya P330-ML Reference Guide included in the configuration file. Therefor e, it is important to reinitiali ze the NVRAM to the factory default set tings before downloading configuration files to the switch. To reinitialize the NVRAM , run the nvram initialize command. The syntax for this command is:[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands Avaya P330-ML Reference Guid e 223 Example: event log Use the event log command to display a list of the event message s. L The event messages shown are e ncrypted and are reserved for Avaya use only. The syntax for this command is: event log [<num>] Example: exit User level: user, privileged, supe[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands 224 Avaya P330-ML Reference Guide Example: fragment chain Use the fragment chain command to set the maximu m number of fragments that can comprise a single IP pack et destined to the router. Use the no form of this command to set the fragment chain to the def ault value (64). L The router does not perfor[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands Avaya P330-ML Reference Guid e 225 Example: fragment timeout Use the fragment timeout command to set the maximum number of seconds to reassemble a fragmented IP packet destined to the router. Use the no form of this command to set the fragment time out to the default va lue (10). L The router does not pe[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands 226 Avaya P330-ML Reference Guide Example: hostname User level: privileged, supervisor. Use the hostname command to change the sys t em prompt used for the router Use the no hostname command to return the system prompt to its default. This command does not change the system prompt of the switch. To ch an[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands Avaya P330-ML Reference Guid e 227 The syntax for this command is: icmp in-echo-limit <size> Example: interface User level: privileged, supervisor. Use the interface command to create and enter the Interface Configuration Mode. Use the no interface command to delete a specific IP interface. The syn[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands 228 Avaya P330-ML Reference Guide action> Example: ip access-group User level: privileged, supervisor. Use the ip access group command to acti vate a specific policy list. The syntax for this command is: ip access-group <policy-list-number> <default-action> Example: ip access -list User le[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands Avaya P330-ML Reference Guid e 229 <source-ip>}[<operator> <port> [<port]] {<destination-ip> <destination- wildcard>|any |host <destination-ip>}[<operator> <port> [<port>]][established] [precedence] Example: ip access-list-cookie User level: privil[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands 230 Avaya P330-ML Reference Guide Example: ip access -list-copy User level: privileged, supervisor. Use the ip access-list-copy command to copy a config ured source policy list to a destinat ion policy lis t. The syntax for this command is: ip access-list-copy <source-list> <destination-list>[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands Avaya P330-ML Reference Guid e 231 Example: ip access-list-dscp trust User level: privileged, supervisor. Use the ip access-list-dscp trust command to decide which original frame fields influence the selection of packet priority. L This command does not apply to th e P333R. The syntax for this command is[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands 232 Avaya P330-ML Reference Guide Example: ip access-l ist-name User level: privileged, supervisor. Use the i p access-list-name command to set a name for a policy list. The syntax for this command is: ip access-list-name <policy-list-number> <name> Example: L If you wish to enter a name whic[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands Avaya P330-ML Reference Guid e 233 Example: ip bootp-dhcp relay User level: privileged, supervisor. L If you are at the ”privileg ed” level, you can only access this command in Configure mode. Type configure at t he c o m m a n d p r om p t t o e n t er c o n f i g ur e m o d e i f ne c e s s a r y .[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands 234 Avaya P330-ML Reference Guide ip default-gateway User level: privileged, supervisor. L If you are at the ”pri vileged” level, you can only access thi s command in Configure mode. Type configure at the command prompt to enter configure mode. Use the ip default-gateway command to define a default g[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands Avaya P330-ML Reference Guid e 235 Example: To set the maximum number of ARP cache entries to 8000: To restore the maximum number of ARP cache entries to its default: ip max-route-entries User level: privileged, supervisor. L If you are at the ”privileg ed” level, you can only access this command in [...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands 236 Avaya P330-ML Reference Guide a dotted decimal. The syntax for this command is: [no] ip netmask-format <mask-format> The possible mask formats are: Example: To display netmasks in decimal format: ip ospf rou ter-id User level: privileged, supervisor. Use the ip ospf router-id c ommand to config[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands Avaya P330-ML Reference Guid e 237 Example: ip route User level: privileged, supervisor. L If you are at the ”privileg ed” level, you can only access this command in Configure mode. Type configure at the command prompt to enter configure mode. Use the ip route command to establish a static route. Use[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands 238 Avaya P330-ML Reference Guide Use the ip routing command to enable IP routing. Use the no ip routing command to disable the IP routing process in the device. By default, IP rou ting is enabled. The syntax for this command is: [no] ip routing Example: ip simulate User level: privileged, supervisor. L [...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands Avaya P330-ML Reference Guid e 239 Example: ping User level: user, privileged, supervisor Use the ping command to send ICMP echo request packets to another node on the network. L You can use this command via the master switch only. L The command is executed until you The syntax for this command is: ping [...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands 240 Avaya P330-ML Reference Guide User level: privileged, supervisor. Use the CLI prompt length command to set the length of the command prompt that is displayed. The syntax for this command is: prompt-length <full | prompt-size> Example: reset User level: user, privileged, supervisor Use the reset[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands Avaya P330-ML Reference Guid e 241 The default is disabled . The syntax for this command is: [no] router ospf Example: router rip User level: privileged, supervisor. L If you are at the ”privileg ed” level, you can only access this command in Configure mode. Type configure at the command prompt to en[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands 242 Avaya P330-ML Reference Guide Example: To enable the srrp: router vrrp User level: privileged, supervisor. L If you are at the ”pri vileged” level, you can only access thi s command in Configure mode. Type configure a t t h e c o m m a n d p r o mp t t o e n t e r co n f i g u re m o d e i f n e [...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands Avaya P330-ML Reference Guid e 243 L When you use the session command the secu rity level stays the same. Example: L The security level stays the same when you use the session command. set device-mode User level: privileged, supervisor. Use the set device-mode command to change the basic mode of operatio[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands 244 Avaya P330-ML Reference Guide set policy type User level: privileged, supervisor. L This command is available on the P334T -ML switch in device mode “Router” only. Use the set policy type command to set whether the P334T-ML module enforces the acti ve policy-list on all packet s or only on routed[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands Avaya P330-ML Reference Guid e 245 Example: set system contact User level: user, privileged, supervisor Use the set system contact command to set the system contact MIB variable. The syntax for this command is: set system contact [string] Example: L If you wish to enter a n a me which includ es spaces, y[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands 246 Avaya P330-ML Reference Guide set system name User level: privileged, supervisor. Use the set system name command to set the mib2 system name MIB variable. The syntax for this command is: set system name [string] Example: L If you wish to enter a name which includes spaces , you must enclose the enti[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands Avaya P330-ML Reference Guid e 247 set vlan User level: privileged, supervisor. L If you are at the ”privileg ed” level, you can only access this command in Configure mode. Type configure at the command prompt to enter Configure mode if necessary. Use the set vlan command to create a rou ter Layer 2 [...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands 248 Avaya P330-ML Reference Guide show device-mode User level: user, privileged, supervisor L This command does not apply to the P333R-LB which is always in “Load Balancing” mode. Use the show device-mode command to show the cu rrent switch operating mode. Possible modes are Router or Switch. The syn[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands Avaya P330-ML Reference Guid e 249 configuration operation. The syntax for this command is: show erase status show fragment User level: user, privileged, supervisor Use the show fragment command to dis play information regard ing fragmented IP packets that are destined to the router. L The router does no[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands 250 Avaya P330-ML Reference Guide show ip access-group User level: user, privileged, supervisor Use the show ip access-group command to see informa tion about the configured active access list . L This command is available on P330-ML-ML switches only. The syntax for this comman d is: show ip access-group[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands Avaya P330-ML Reference Guid e 251 show ip access-list-dscp User level: user, privileged, supervisor Use the show ip access-list-dscp command to display the DSCP to CoS map of a policy-list. The syntax for this command is: show ip access-list-dscp <policy-list-number> [<dscp>] Example: show i[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands 252 Avaya P330-ML Reference Guide Example: show ip arp User level: user, privileged, supervisor Use the show ip arp command to display the Addres s Resolution Pr otocol (A RP) cache. The syntax for this command is: show ip arp [<if-name> | <vlan> | <ip addr> | <ip-mask> static] Ex[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands Avaya P330-ML Reference Guid e 253 show ip icmp User level: user, privileged, supervisor Use the show icmp ip command to display the status of ICMP error mes sages. The syntax for this command is: show ip icmp Example: show ip interface User level: user, privileged, supervisor Use the show ip interface c[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands 254 Avaya P330-ML Reference Guide Example: L If you wish to enter a name which includes spaces , you must enclose the entire name in quotation marks, for example “new york”. show ip inter face brief User level: user, privileged, supervisor Use the show ip interface brief command to display brief info[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands Avaya P330-ML Reference Guid e 255 Example: show ip ospf User level: user, privileged, supervisor Use the show ip opsf command to displays general information about OSPF routing. The syntax for this command is: show ip ospf Example: show ip ospf databa se User level: user, privileged, supervisor Displays[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands 256 Avaya P330-ML Reference Guide show ip ospf i nterface User level: user, privileged, supervisor Use the show ip ospf interface command to display OSPF-related interface information. The syntax for this command is: show ip ospf interface [<interface-name>] Example: L If you wish to enter a name w[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands Avaya P330-ML Reference Guid e 257 Example: L If you wish to enter a n a me which includ es spaces, you must enclose the entire name in quotation marks, for example “new york”. show ip protocols User level: user, privileged, supervisor Use the show ip protocols command to display the IP routing proto[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands 258 Avaya P330-ML Reference Guide show ip reverse-arp User level: user, privileged, supervisor Use the show ip reve rse-arp command to display the IP address of a host, based on a known MAC address. The syntax for this command is: show ip reverse-arp <mac addr> [<match len>] Example: show ip [...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands Avaya P330-ML Reference Guid e 259 show ip route best-match User level: user, privileged, supervisor Use the show ip route best-match command to display a routing table for a destination address. The syntax for this command is: show ip route best-match <dst addr> Example: show ip route static User [...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands 260 Avaya P330-ML Reference Guide show ip route summary User level: user, privileged, supervisor Use the show ip route summary command to display the number of routes known to the switch. The syntax for this command is: show ip route summary Example: show ip ssh User level: superviso r Use the show ip ss[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands Avaya P330-ML Reference Guid e 261 The syntax for this command is: show ip srrp Example: show ip traffic User level: user, privileged, supervisor L This command does not apply to th e P333R-LB. Use the show ip traffic command to display the IP traffic statistics counters. The syntax for this command is: [...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands 262 Avaya P330-ML Reference Guide Example: Router-N> show ip traffic IP statistics: Received: 1365359 total, 45659 local destination 0 bad hop count, 0 packet header errors 0 unknown protocol, 136786 address errors 1182914 discarded Fragments: 0 reassembled, 0 timeouts 0 couldn't reassemble, 0 fr[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands Avaya P330-ML Reference Guid e 263 show ip unicast cac he User level: privileged, supervisor. Use the show ip unicast cache command to list the entries in the hardware unicast cache database. The syntax for this command is: show ip unicast cache [[<src addr> <src mask>] <dst addr> <d[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands 264 Avaya P330-ML Reference Guide Example: show ip unicast c ache networks User level: user, privileged, supervisor Use th e show ip unicast cache networks command to display a summary of networks handled by the hardware unicast cache database. The syntax for this command is: show ip unicast cache networ[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands Avaya P330-ML Reference Guid e 265 Example: show ip unicast cac he networks de tailed User level: user, privileged, supervisor Use the show ip unicast cache networks detailed command to list the networks and hosts that are handled by the hardware unicast cache database. The syntax for this command is: sh[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands 266 Avaya P330-ML Reference Guide Example: show ip unicast c ache nextHop User level: privileged, supervisor. Use the show ip uni cast cache nextHop command to list the routers that are used as next-hop routers. The syntax for this command is: show ip unicast cache nextHop Example: show ip unicast c ache[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands Avaya P330-ML Reference Guid e 267 Example: show ip vrrp User level: user, privileged, supervisor Use the show vrrp command to display VRRP information. The syntax for this command is: show ip vrrp [<vlan> [router-id <vr-id>]][detail] Example: show ip vrrp detai l User level: user, privileged[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands 268 Avaya P330-ML Reference Guide Example: show policy type User level: user, privileged, supervisor L This command is availabl e on the P334T-ML only. Router-N> show ip vrrp detail VRRP is globally enabled Virtual Router on VLAN: 1 Router-id: 1 State: MASTER Priority: 255 Advertisement Interval: 1 La[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands Avaya P330-ML Reference Guid e 269 Use the show policy type command to show whether the module enforces the active policy-list on al l packets or only on routed packets ( for modules in 'device- mode router'). The syntax for this command is: show policy type Example: Router-N# show policy type [...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands 270 Avaya P330-ML Reference Guide show startup-config User level: user, privileged, supervisor Use the show startup-config command to show conf iguration loaded at startup. The syntax for this command is: show startup-config Example: show system User level: user, privileged, supervisor Use the show syste[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands Avaya P330-ML Reference Guid e 271 show upload status User level: user, privileged, supervisor Use the show upload status commands to display the status of the current configuration file copy process from the device. The syntax for this command is: show upload status [<mod_num>] Example: show vlan [...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands 272 Avaya P330-ML Reference Guide The syntax for this command is: terminal {width|length} [<characters>] Example: traceroute User level: user, privileged, supervisor Use the traceroute command to initiate a trac eroute to a remote host. The syntax for this command is: traceroute <host> Exampl[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands Avaya P330-ML Reference Guid e 273 L The validation process may take some time to complete.[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands 274 Avaya P330-ML Reference Guide Interface Context L You can only access these comma nds in the “interface” context. Type interface [name] at the command prompt to enter the “interface” context if necessary. default-metri c User level: privileged, supervisor. Use the default metric command to se[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands Avaya P330-ML Reference Guid e 275 ip address User level: privileged, supervisor. Use the ip address command to assign an IP address and mask to an interface. The syntax for this command is: ip address <ip-address> <mask> [<admin-state>] Example: To assign the IP address 192.168.22.33 w[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands 276 Avaya P330-ML Reference Guide ip bootp-dhcp network User level: privileged, supervisor. Use the ip bootp-dhcp network command to configure the network from which the BOOTP/DHCP server shal l allocate an address. Use the no ip bootp-dhcp network comm and to remove a network. L Multiple networks can be[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands Avaya P330-ML Reference Guid e 277 Example: To add station 192.168.37.46 as a bootp/dhcp server to handle bootp/dhcp requests arriving at the interface “marketing”: ip broadcast-address User level: privileged, supervisor. Use the ip broadcast command to update the inte rface broadcast address. The Br[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands 278 Avaya P330-ML Reference Guide ip netbios-reb roadcast User level: privileged, supervisor. Use the ip netbios-rebroadcast command to set the NETBIOS rebroadcasts mode on an interface. Use the no ip netbios-rebroadcast command to disable NETBIOS rebroadcasts on an interface. The syntax for this command[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands Avaya P330-ML Reference Guid e 279 ip ospf cost User level: privileged, supervisor. Use the ip ospf command to configure interface metric. Use the no ip ospf cost command to set the cost to its default. The default is 1. The syntax for this command is: [no] ip ospf cost <cost> Example: ip ospf dead[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands 280 Avaya P330-ML Reference Guide The syntax for this command is: [no] ip ospf hello-interval <seconds> Example: ip ospf prio rity User level: privileged, supervisor. Use the ip ospf priority command to configure interface priority used in DR election. Use the no ip ospf priority to set the OSPF pr[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands Avaya P330-ML Reference Guid e 281 ip redirects User level: privileged, supervisor. Use the ip redirects command to enables the send ing of redirect messages on the interface. Use the no ip redirect command to disable the redir ect messages. By default, sending of redir ect messages on the interface is e[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands 282 Avaya P330-ML Reference Guide ip rip authentica tion mode User level: privileged, supervisor. Use the ip rip authentication command to specify the type of authentication used in RIP Version 2 packets. Use the no ip rip authentication command to restore the default value of none. The syntax for this c[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands Avaya P330-ML Reference Guid e 283 Example: ip rip poison-reverse User level: privileged, supervisor. L You can only access this command in interface mode. Type interface [name] at the command prompt to enter interface mode if necessary. Use the ip rip poison-reverse command to enable split-horizon with [...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands 284 Avaya P330-ML Reference Guide The possible versions of the RIP packets r eceived and sent on an interface ar e: Example: To specify that RIP version 2 should be running on the basis of the interface “marketing”: ip rip send-receive-m ode User level: privileged, supervisor. Use the ip rip send-rec[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands Avaya P330-ML Reference Guid e 285 ip rip split-hor izon User level: privileged, supervisor. Use the ip rip split-horizon command to enable split-horizon mechanism. Use the no ip rip split-horizon command to disable the split-hor izon. By default split-horizon i s enabled. The split-horizon technique pre[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands 286 Avaya P330-ML Reference Guide ip srrp backup User level: privileged, supervisor. Use the ip srrp backup command to backup an additional interface of the main router using the SRRP application. If the main router fails, the switch takes over its activities on all configured interfaces. The syntax for [...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands Avaya P330-ML Reference Guid e 287 ip vrrp User level: privileged, supervisor. Use the ip vrrp command to create a virtual router on the interface. Use the no ip vrrp command to delete a virtual router. The syntax for this command is: [no] ip vrrp <vr-id> Example: ip vrrp address User level: privil[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands 288 Avaya P330-ML Reference Guide ip vrrp auth-key User level: privileged, supervisor. Use the ip vrrp auth-key command to set the virtual router simple password authentication for the virtual router ID. Use the no ip vrrp auth-key command to disable simple password authentication for the vi rtual rou te[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands Avaya P330-ML Reference Guid e 289 ip vrrp preempt User level: privileged, supervisor. Use the ip vrrp preempt command to configure the router to preempt a lower priority master for the virtual router ID. Use the no ip vrrp preempt command to disable pr eemption for the virtual router instance. By defaul[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands 290 Avaya P330-ML Reference Guide ip vrrp prior ity User level: privileged, supervisor. Use the ip vrrp priority command to set the virtual router priority value used when selecting a master route r. Use the no ip vrrp priority command to restore the default value. The syntax for this command is: [no] ip[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands Avaya P330-ML Reference Guid e 291 Router RIP Context L You can only access these commands in the “Router-RIP” context. Type router rip a t the command prompt to enter the “Rou ter-RIP” context if necessary. network User level: privileged, supervisor. Use the network command to specify a list of [...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands 292 Avaya P330-ML Reference Guide Example: timers basic User level: privileged, supervisor. Use the timers basic command to configure the route timer. Use the no timers basic command to restore the timers to their default values. The syntax for this command is: timers basic <update><invalid> [...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands Avaya P330-ML Reference Guid e 293 Router OSPF Context L You can only access these comman d in the “Router-OSPF” context. Type router ospf at the command prompt to enter the “Router -OSPF” context if necessary. area User level: privileged, supervisor. Use the area command to configure the area ID[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands 294 Avaya P330-ML Reference Guide Example: passive-int erface User level: privileged, supervisor. Use the passive interface command to allow interfaces to be flooded into the OSPF domain as OSPF routes an d not external routes. L An interface becomes passive only if you use the network command to enable [...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands Avaya P330-ML Reference Guid e 295 Example: timers spf User level: privileged, supervisor. Use the timers spf command to configure the delay between runs of OSPF’s SPF calculation. Use the no form of this command to restore the default (3 seconds). The syntax for this command is: [no] timers spf <sp[...]

Chapter 3 Avaya P330-ML Layer 3 CLI Commands 296 Avaya P330-ML Reference Guide Router SRRP Context L You can only access these commands in the “Router-SRRP” context. Type router srrp at the command prompt to enter the “Router -SRRP” context if necessary. poll-int erval User level: user, privileged, supervisor Use the poll-inte rval command [...]

Avaya P330-ML Reference Guide 297 Index of Layer 2 CLI Commands C clear cam 9 clear dynamic vlans 10 clear event-log 10 clear interface 11 , 21 4 clear ip route 11 , 214 clear logging fi le 10 clear logging ser v er 11 clear port mirror 11 clear port static-vlan 12 clear power history 12 clear radius authentication server 12 clear rmon statistics 1[...]

Index of Layer 2 CLI Commands 298 Avaya P330-ML Reference Guide rmon alarm 55 rmon event 56 rmon history 56 S session 57 , 242 set allowed managers 58 set allowed managers ip 58 set arp-aging-int erval 59 set arp-tx-interval 59 set autopartition 60 set boot bank 199 set cascading 61 set device-mode 61 set inband vlan 65 set intelligent-multicast 65[...]

Index of Layer 2 CLI Commands Avaya P330-ML Reference Guide 299 set terminal recovery password disable 121 set terminal recovery password enable 121 set time client 122 set time protocol 122 set time server 123 set timezone 123 set trunk 124 set utilizatio n cpu 124 set vlan 125 set web aux-files-ur l 125 show timezone 194 show allowed managers sta[...]

Index of Layer 2 CLI Commands 300 Avaya P330-ML Reference Guide snmp-server enable notifications 200 snmp-server engineID 200 snmp-server group 201 snmp-server host 202 snmp-server informs 203 snmp-server remote-user 204 snmp-server user 205 snmp-server view 206 sync time 207 T tech 207 telnet 207 terminal 9 U username 208[...]

Avaya P330-ML Reference Guide 301 Index of Layer 3 CLI Commands area 309 arp 212 arp timeout 212 clear arp-cache 213 clear fragment 214 clear ip route 214 clear ip traffic 215 clear screen 215 clear vlan 215 configure 216 copy module-config scp 216 copy module-config tftp 217 copy running-config scp 218 copy running-config startup-config 219 copy r[...]

Index of Layer 3 CLI Commands 302 Avaya P330-ML Reference Guide ip simulate 240 ip srrp backup 302 ip unicast cache aging 241 ip unicast cache aging timeout 241 ip unicast cache high- lim it 242 ip unicast cache update-timeout 242 ip vlan/ip vlan name 302 ip vrrp 303 ip vrrp address 303 ip vrrp auth-key 304 ip vrrp override addr owner 304 ip vrrp p[...]

Index of Layer 3 CLI Commands Avaya P330-ML Reference Guide 303 show rmon2 matrix 282 show rmon2 matrix-top-n 284 show rmon2 protocol-dist 280 show rmon2 protocol-dist-top-n 285 show rmon2 state 280 show rmon2 subnets 282 show rmon2 subnet-top-n 285 show startup-config 286 show system 286 show upload status 287 show vlan 287 terminal 287 timeout 31[...]

Index of Layer 3 CLI Commands 304 Avaya P330-ML Reference Guide[...]