Bertazzoni PM36 3 0G X Bedienungsanleitung

INSTALLATION, MAINTENANCE AND USE INSTRUCTIONS FOR DIMENSIONS: (890 mm) (W) x (520 mm) (D) Model PM3630GX IMPORTANT: SAVE FOR LOCAL ELECTRI CAL INSPECTOR’S USE. READ AND SAVE THESE INSTR UCTIONS FOR FUTURE REFER ENCE. OBSERVE ALL GOVERNING C ODES AND ORDINANC ES.[...]

2 WARNING: If the information in this ma nual is not followed exactly, a fire or explosion may result causing property da mage, personal injury or death. Do not store or use gasoline or other fla mmable vapors and liquid in the vicinity of this or any other appliance. WHAT TO DO IF YOU SMELL GAS - Do not try to light any appliance. - Do not touc h [...]

3 INDEX: Installation Instructions……………………………………..……………………….. pag.3 Inserting the hotplate……………………………………………..………………….. pag.4 Requirements……………………………………..……………………………….….. pag.4 Attaching the hotplate…?[...]

4 INFORMATION FOR THE INSTALLER The installation, all regulat ions, changes and maintenan ce referred to in this part must only be carried out by qualified staff. A wrong installation can cause damage to pe rsons, anima ls or things which the manufacturer cannot be held responsible for. The safety and automatic regulation devices on the appliances [...]

5 (*) Note: -B1 is the min. clearance between the front edge of the applia nce and the front edge of the cabinet. -B2 and B4 are the min. cl earance between the l eft/right side edge of the applianc e and the side wall (if present). -B3 is the min. clearance between the b ack edge of the appliance and the back wall. -L2 plus L8 is the minimum dista[...]

6 A label on the last page of this manual and on the lo w er part of the case indicates the conditions for regulating the appliance: type of gas and press ure used. IMPORTANT: This appliance mu st be installed in accordanc e with the norms in force of the country concerned and it must only be used in a well-ventilated place. ATTENTION: Remember tha[...]

7 When the connection is made directly with the electricity supply : - Make sure that there is a device to disconnect the appliance from the mains with a contact opening distance sufficient for complete disconne ction in category III overvoltage conditions. - Place a single-pole switch between the appliance and the electricity supply. The switch mu[...]

8 BEFORE LEAVING When the installation is co mplete, always check for gas leaks usi ng a soapy solution. Never use a flame t o make this check. Ignite all burners on high flame to ensure correct opera tion of gas valves, burne rs and ignition. Turn gas taps to low flame position and observe each burne r to ensure t hey ignite completely at all port[...]

9  Use Proper Pan Size - This applian ce is equipped with several, differently sized, induction elements. Select cookware having flat bottoms, large enough to cover the su rface unit heating element. Proper size pots and pans will also improve efficien cy.  DO NOT TOUCH SURFACE UNITS OR AREAS NEAR UNITS - Surface units may be hot even though [...]

10 Turn the knob that corre sponds to the burner sele ct ed counterclockwise to th e MAXIMUM position at the etched star (large flame) a nd place a lit match up to the burner. Burners fitted with a safety device (thermocouple ): Turn the knob that corre sponds to the burner sele ct ed counterclockwise to the MAXIMUM position at the etched star (lar[...]

11 You can select the whole griddle zo ne, or only the front or rear zone. Press and turn the knob anti-clockwi se to the selected position (Fig.16-17) Pre-heat at the maximum temperature, (7 position) for 15 minutes, then place the food on the griddle a nd cook to the desired temperature. The activation of the griddle is shown by the indicator lig[...]

12 heavy, coarse cloth, it will need to be reseasoned. Never flood the hot grid dle with cold water. This could cause the griddle to crack or wa rp. Do not touch the griddle when it is hot Note: do not use the scouring sponge to clean the stainl ess-steel frame, this will l eave scratch marks. Do not use metal pot cleaners, steel wool, wire brush o[...]

13 SERVICE & MAINTENANCE INSTRUCTIONS Service and maintenance only to be carried out by an authorised person Routine maintenance Have the condition and efficiency of the gas pipe and the pre ssure regulator (if installed) checked periodically. If anomalies are found, do n ot repair compone nts but have the faulty component replaced. To ensure g[...]

14 AFTER-SALES TECHNICAL SE RVICE AND SPARE PARTS Before leaving the factory, this appliance wa s tested and adjusted by speciali st skilled staff to give the best operating results. Any subsequent necessary rep airs or adjustments must be carried out with the greatest care and attention by auth orised personnel. For th is reason, we strongly advis[...]

15 Fig 1 Fig 2 Fig.3 Fig. 3A Fig. 3B[...]

16 Fig.4 Fig.5A Fig.5B Fig.6 Fig.7 Fig.8 Fig.9 Fig.10 Fig.11[...]

17 Fig.12 Fig.13 Fig.14 Fig.15 Fig.16 Fig.17 Fig.18[...]

18 Fig.19 Fig.20[...]

19 Fig.21 Cod. 310788[...]