Bosch DHI 655 F Bedienungsanleitung

DH I 645 F / DH I 655 F a Internet : http://www.bosch-hausgeraete.de Bosch Info- T eam: de T el. 01 80/5 30 40 50 ( E 0, 1 2/ Min. DT AG) de Gebrauchs- und Montageanleit ung en Operating and installat ion instruct ions fr Mode d’emploi et notice de mont age nl Gebruiksaanwijzing en montagevoorschrift it Istruzioni d’uso e per il montaggio es In[...]

2 Abb. 1 GAS ELEKTRO GAZ ELECTR. KAASU ELETT . GASS EL. de Seite 0 3–1 5 en page 16 – 28 fr page 29 – 41 nl pagina 42 – 54 it pagina 55 – 67 es página 68 – 80 pt página 81 – 93[...]

16 Operating modes This can be achieved if the combustion air is able to flow through non-lockable openings, e.g. in doors, windows and in conjunction with an air supply/air -intake wall box or by other technical procedur es such as recipr ocal interlocking. If the air intake is inadequate, there is a risk of poisoning from combustion gases which [...]

17 Before using for the first time Important notes: ❑ The Instructions for Use apply to several versions of this appliance. Accordingly , you may find descriptions of individual features that do not apply to your specific appliance. ❑ This extractor hood complies with all re levant safety regulations. Repairs should be carried out by quali?[...]

18 Operating the extractor hood  Cooking vapours are best eliminated by: ❑ Switching on the extractor hood when you start cooking. ❑ Only switching off the extractor hood a few minutes after you have finished cooking. Fan on / off Light on / off Intensive setting Fan settings Fan on / off Intensive setting Reset button with saturation displ[...]

19 4. Clean the filters. 5. Insert the clean filters back into the hood. 6. Cancel the in the display . ❑ Press the button. Grease filters: Metal-mesh filters are used to trap the grease particles in the cooking vapours. The filter mats are made fr om non- combustible metal. Caution: As the filter becomes more and mor e saturated with greas[...]

20 3. Engage the catches at both sides. 4. Insert the metal-mesh grease filters (see ”Removing and inserting the metal-mesh grease filters”). Removing the filter: Wa r ning: The halogen bulbs must be switched off and cool. 1. Remove the metal-mesh filters. 2. Depress the catches on both sides of the filter and remove the activated carbon ?[...]

21 Cleaning and care Isolate the extractor hood by pulling out the mains plug or switching off the fuse. ❑ When cleaning the grease filters, r emove grease deposits fr om accessible parts of the housing. This prevents the risk of fir e and ensures that the extractor hood continues operating at maximum efficiency . ❑ Clean the extractor hood w[...]

22 Important information Installation Instructions:  The installation of the extractor hood above gas cooking devices, at a minimum height of 650 mm – Fig. 1 – is permitted provided that the following nominal heat loads (Hs) are not exceeded: ❑ Gas cookers Load of one hotplate max. 0 3.0 kW Load of all hotplates max. 0 8.3 kW Load of the o[...]

23 Prior to installation Exhaust-air mode The exhaust air is discharged upwards through a ventilation shaft or dir ectly through the outside wall into the open. D Exhaust air must not be discharged via a smoke or exhaust gas flue which is already in use or via a shaft which is used for ventilating rooms in which fir eplaces are located. Discharge[...]

24 Before installation Optimum efficiency of the extractor hood: ❑ Short, smooth exhaust pipe. ❑ As few bends as possible. ❑ Pipe diameter as large as possible (ideally 150 mm dia.) and wide pipe bends. If long, rough exhaust-air pipes, many pipe bends or smaller pipe diameters are used, the air extraction rate will no longer be at an optimum[...]

25 Preparing the wall cupboar d This extractor hood is designed to be installed in a wall cupboard with the follo- wing dimensions: width: 600 mm depth: 293 to 350 mm height: min. 435 mm. If the cupboard is deeper than 293 mm, the extractor hood can be moved back, e.g. to put a spice rack in front of the extractor hood. To do this, place the templa[...]

26 3. T ighten the two fixing screws with a screwdriver (cor dless). 4. If requir ed, shorten the wall cover to the r equir ed dimension (e.g. saw off). Attach the wall cover with the enclosed clips. Screw the wall cover to the wall cupboard. 5. Feed the mains connection cable out of the cupboard. 6. Connect the pipes in the wall cupboard. – If [...]

27 Fitting into wall cupboard ❑ If the extractor hood is to be installed further back in the cupboard, the stops for the filter drawer can be moved forwards. ❑ To do this, undo the screws, move the stops and retighten the scr ews. 2. Align handle moulding and screw to the appliance. Exhaust air Circulating air 13,0 13,5 We reserve the right to[...]

28 Electrical connection W ARNING: THIS APPLIANCE MUST BE EARTHED IMPORT ANT : Fitting a Differ ent Plug: The wires in the power cor d are colour - coded as follows: Green and Y ellow – Earth Blue – Neutral Brown – Live If you fit your own plug, the colours of these wires may not corr espond with the identifying marks on the plug terminals. [...]

95 Notes[...]

Notes 96[...]

DHZ 4505 434229 1 3 4 2 5 3x Aluminium: DHZ 4670 Metall: DHZ 4650 DHZ 4600 Absenkrahmen Lowering frame Du cadre d’abaissement Befestigingsframe Dei telai per l’abbassamento Bastidor para bajar[...]

5750 203 748 Printed in Germany 0704 Es. Robert Bosch Hausgeräte GmbH[...]