Buffalo Technology WHR-HP-G54 Bedienungsanleitung
- Schauen Sie die Anleitung online durch oderladen Sie diese herunter
- 91 Seiten
- 7.41 mb
Zur Seite of
Ähnliche Gebrauchsanleitungen
-
Network Router
Buffalo Technology WZR2-G300N
6 Seiten 1.53 mb -
Network Router
Buffalo Technology WHR-G54S-QSG
6 Seiten 0.42 mb -
Network Router
Buffalo Technology WHR-G300N
48 Seiten 1.65 mb -
Network Router
Buffalo Technology WZR-G108
12 Seiten 0.77 mb -
Network Router
Buffalo Technology WRB-G54K
24 Seiten 3.51 mb -
Network Router
Buffalo Technology WBR2-G54S
95 Seiten 1.79 mb -
Network Router
Buffalo Technology HD-HGLAN
9 Seiten 0.37 mb -
Network Router
Buffalo Technology WZR-G240
7 Seiten 1.28 mb
Richtige Gebrauchsanleitung
Die Vorschriften verpflichten den Verkäufer zur Übertragung der Gebrauchsanleitung Buffalo Technology WHR-HP-G54 an den Erwerber, zusammen mit der Ware. Eine fehlende Anleitung oder falsche Informationen, die dem Verbraucher übertragen werden, bilden eine Grundlage für eine Reklamation aufgrund Unstimmigkeit des Geräts mit dem Vertrag. Rechtsmäßig lässt man das Anfügen einer Gebrauchsanleitung in anderer Form als Papierform zu, was letztens sehr oft genutzt wird, indem man eine grafische oder elektronische Anleitung von Buffalo Technology WHR-HP-G54, sowie Anleitungsvideos für Nutzer beifügt. Die Bedingung ist, dass ihre Form leserlich und verständlich ist.
Was ist eine Gebrauchsanleitung?
Das Wort kommt vom lateinischen „instructio”, d.h. ordnen. Demnach kann man in der Anleitung Buffalo Technology WHR-HP-G54 die Beschreibung der Etappen der Vorgehensweisen finden. Das Ziel der Anleitung ist die Belehrung, Vereinfachung des Starts, der Nutzung des Geräts oder auch der Ausführung bestimmter Tätigkeiten. Die Anleitung ist eine Sammlung von Informationen über ein Gegenstand/eine Dienstleistung, ein Hinweis.
Leider widmen nicht viele Nutzer ihre Zeit der Gebrauchsanleitung Buffalo Technology WHR-HP-G54. Eine gute Gebrauchsanleitung erlaubt nicht nur eine Reihe zusätzlicher Funktionen des gekauften Geräts kennenzulernen, sondern hilft dabei viele Fehler zu vermeiden.
Was sollte also eine ideale Gebrauchsanleitung beinhalten?
Die Gebrauchsanleitung Buffalo Technology WHR-HP-G54 sollte vor allem folgendes enthalten:
- Informationen über technische Daten des Geräts Buffalo Technology WHR-HP-G54
- Den Namen des Produzenten und das Produktionsjahr des Geräts Buffalo Technology WHR-HP-G54
- Grundsätze der Bedienung, Regulierung und Wartung des Geräts Buffalo Technology WHR-HP-G54
- Sicherheitszeichen und Zertifikate, die die Übereinstimmung mit entsprechenden Normen bestätigen
Warum lesen wir keine Gebrauchsanleitungen?
Der Grund dafür ist die fehlende Zeit und die Sicherheit, was die bestimmten Funktionen der gekauften Geräte angeht. Leider ist das Anschließen und Starten von Buffalo Technology WHR-HP-G54 zu wenig. Eine Anleitung beinhaltet eine Reihe von Hinweisen bezüglich bestimmter Funktionen, Sicherheitsgrundsätze, Wartungsarten (sogar das, welche Mittel man benutzen sollte), eventueller Fehler von Buffalo Technology WHR-HP-G54 und Lösungsarten für Probleme, die während der Nutzung auftreten könnten. Immerhin kann man in der Gebrauchsanleitung die Kontaktnummer zum Service Buffalo Technology finden, wenn die vorgeschlagenen Lösungen nicht wirksam sind. Aktuell erfreuen sich Anleitungen in Form von interessanten Animationen oder Videoanleitungen an Popularität, die den Nutzer besser ansprechen als eine Broschüre. Diese Art von Anleitung gibt garantiert, dass der Nutzer sich das ganze Video anschaut, ohne die spezifizierten und komplizierten technischen Beschreibungen von Buffalo Technology WHR-HP-G54 zu überspringen, wie es bei der Papierform passiert.
Warum sollte man Gebrauchsanleitungen lesen?
In der Gebrauchsanleitung finden wir vor allem die Antwort über den Bau sowie die Möglichkeiten des Geräts Buffalo Technology WHR-HP-G54, über die Nutzung bestimmter Accessoires und eine Reihe von Informationen, die erlauben, jegliche Funktionen und Bequemlichkeiten zu nutzen.
Nach dem gelungenen Kauf des Geräts, sollte man einige Zeit für das Kennenlernen jedes Teils der Anleitung von Buffalo Technology WHR-HP-G54 widmen. Aktuell sind sie genau vorbereitet oder übersetzt, damit sie nicht nur verständlich für die Nutzer sind, aber auch ihre grundliegende Hilfs-Informations-Funktion erfüllen.
Inhaltsverzeichnis der Gebrauchsanleitungen
-
Seite 1
www .bu ffa lo tech.com User Manual - AirStation WHR-HP-G54 High-Power Wireless Cable/DSL Smart Router v1.5[...]
-
Seite 2
2 Table of Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Basic Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 AOSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Router Access Point Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 AirStation Con[...]
-
Seite 3
3 Table of Contents DHCP Server . . . . . . . . . . . . . . . . . . . . . 29 Ma nu al Ass ig nm e nt of IP Addr es s . . . 30 Network Conguration. . . . . . . . . . . . . . . . . . . . . 31 Route information . . . . . . . . . . . . . . . . . . . . 31 Ad dr es s T ran sl at io n . . . . . . . . . . . . . . . . . . . . . . . . . . 33 IP Filter . .[...]
-
Seite 4
4 Table of Contents D a t e / N T P . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 S y s l og T r a ns f er . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 8 Sa v e/ L oa d Con gu r at ion . . . . . . . . . . . . 49 I n it ia li ze /R eb oo t . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Fi rm w a re U pd at e[...]
-
Seite 5
5 W ork and play - further and faster! Eliminate dead spots and enjoy faster connections with vastly extended range from Buffalo Technology’s amazing wireless solution, the AirStation High Power Wireless Broadband SmartRouter . System Requirements • A high-speed (Broadband) Internet connection or existing local area connection. • A computer w[...]
-
Seite 6
6 B eg in by n di n g a go o d pl a ce to set up you r rou t er / ac ce s s po i nt . S o me th in g s to consider: • You’ll need to be able to plug your internet connection into it, so it should go within reach of the LAN cable from your DSL or Cable modem. You’ll also want a power outlet nearby. • Keep the access point as central in yo[...]
-
Seite 7
7 M ake note of the AirStation’s wired MAC address . The LAN or Wired MAC address is the default SSID (wireless network name) of the AirStation. You can find it on the bottom of the AirStation. You may also wish to contact your ISP to ask if other information, such as global IP address, subnet mask address, default gateway address, DNS server add[...]
-
Seite 8
8 1. Power down the Cable or DSL modem and the computer which will be used to congure the AirStation router. 2. Plug the Cable or DSL’s LAN Ethernet cable into the AirStation’s WAN port. Initially, you may need to unplug this cable from your computer, hub or other router. 3. Plug the provided Ethernet cable into a LAN port on the AirStation [...]
-
Seite 9
9 L aunch a web browser on the computer that you’re going to use to congure the AirStation. Enter 192.168.11.1 into the URL eld. Naturally, if you change your AirStation’s IP address, you’ll have to enter the new address instead. A window will open, prompting you to enter a User ID and Password. Enter root as the User name and leave the[...]
-
Seite 10
10 Y our AirStation’s SmartRouter technology will determine the type of internet connection you have automatically, and ask you for any needed information. If your ISP assigns IPs automatically (most cable providers do), their DHCP server will give your router an IP address. If additional login information is required to connect to the internet, [...]
-
Seite 11
11 This is the opening page of your AirStation’s conguration tool. You can always get to it from within the conguration screens by clicking on Home . From here, you can congure port mapping for your internet games, turn on UPnP for Windows (MSN) Messenger , congure your Firewall , setup Encryption , choose your Wireless channel , upda[...]
-
Seite 12
12 AOSS AOSS (AirStation One-Touch Secure System) is a simple system for conguring your wireless network securely. If your router and your client device are installed and both support AOSS, then making a secure wireless connection between them is very easy. Push the AOSS button on the top of your router and hold it in for a few seconds. The AOSS[...]
-
Seite 13
13 Some things to keep in mind • Only one AOSS wireless client adapter can be congured with the AOSS router at a time. The buttons will need to be re-pressed to connect each additional AOSS wireless client adapter. • It is not necessary to AOSS client devices that have already been congured via AOSS, unless signicant changes have been [...]
-
Seite 14
14 Th i s A ir Sta ti on su ppo rt s q ui ckl y cha n gi n g t he pr o du c t fro m a w ir ele ss ro ut er to a c on v en t io nal ac c es s p oin t. Pu t y o ur Ai rs tat io n i nt o A cc ess P oin t M o de by mo v in g t he sw it ch on th e bot to m o f y o ur Ai r St a ti on fr om AU TO to BR I. T hi s c h an g es th e d e fa ult I P a dd res s [...]
-
Seite 15
15 If your wireless client doesn’t support AOSS, you’ll have to congure it manually. From the Home page, click on the System Info tab. Manual Client Configuration[...]
-
Seite 16
16 T his page gives you all the information you might need to congure your non-AOSS wireless client. Probably you’ll just need the SSID, encryption type, and password. Consult your wireless client’s documentation for more information on conguring it if necessary. You can get here from Home by clicking the System Info tab. System Info[...]
-
Seite 17
17 AirStation Configuration Tool (Home) W hen you rst open your AirStation Conguration Tool, it will take you to Home (see also page 11). From Home, you can congure port mapping for your internet games, set UPnP for Windows (MSN) Messenger , congure your rewall , setup encryption , choose your wireless channel , update your AirStatio[...]
-
Seite 18
18 Internet Games (Port Mapping) Select any ports that need to be opened for your internet games to function correctly. Consult your game’s documentation for more information on what ports need to be congured.[...]
-
Seite 19
19 Firewall/Intrusion Detector From this page, choose the level of rewall security you desire. You may also choose to have alerts sent to a different PC, if you like. Click Next when done to restart the router. Get to this page from Home by clicking on Firewall/Intrusion Detector.[...]
-
Seite 20
20 Windows (MSN) Messinger/UPnP Windows (MSN) Messinger requires UPnP for proper operation. You may Enable UPnP here. UPnP may need to be congured on your PC as well. If you need to congure UPnP on your PC, the links at the bottom of the page have instructions for doing so on Windows ME and XP computers. Get to this page from Home by clicking[...]
-
Seite 21
21 Wireless Encryption This page is available from Home by selecting Wireless Encryption . Here, you can manually select the type of wireless encryption you’d like to use. Your AirStation supports three different encryption schemes; choose the best one that all your clients support. Virtually all wireless clients support WEP . It’s a lot better[...]
-
Seite 22
22 This page is available from Home by selecting Wireless channel . With Auto Channel selected, your AirStation will choose the best channel available. Current channel will show the channel that your AirStation is currently using. You may also select any channel from 1-11 manually. Channels 1, 6, and 11 are non-overlapping. If multiple channels are[...]
-
Seite 23
23 This page is available from Home by selecting Firmware update . Use Browse to select your rmware update le, and then click on Apply . Firmware update may take several minutes to complete. Don’t power down your AirStation until the diag LED has gone out. Firmware Update[...]
-
Seite 24
24 Internet Connection (Multisession Reset) From Home , selecting the Internet Connection Wizard (Multisession Reset) tab will begin the Internet Connection Wizard. The Internet Connection Wizard will only function correctly in simple networks, where your cable or DSL modem is plugged directly into your AirStation’s WAN port. If you have a compli[...]
-
Seite 25
25 Advanced Settings Advanced Settings lets you congure every element of your AirStation. Get to Advanced Settings from Home by clicking the Advanced Tab. You may return to Home by clicking on the yellow > Home link in the top left corner. Click Help in the top right corner for more information about any of the pages in Advanced Settings. To [...]
-
Seite 26
26 WAN Config (WAN Port) Here, you may choose how the AirStation acquires an IP address. Normally, the internet connection wizard will set this for you if you have a cablemodem or DSL. If you’re not sure what to choose, perform Easy Setup . To setup PPPoE manually, click on click here and turn to page 27. Also on this page, under Advanced Setup ,[...]
-
Seite 27
27 PPPoE Many DSL connections require a PPPoE Connection in order to log in to an internet connection. Normally, the Easy Detection Wizard will help you congure that, but you may manually congure one here. Consult your ISP for more information on correctly conguring your PPPoE connection. To add a new PPPoE connection, click Edit Connectio[...]
-
Seite 28
28 LAN Config (LAN Port) Default for the LAN side IP address is 192.168.11.1. To add the AirStation to an existing LAN, specify a unique IPaddress, not used elsewhere in the network. The default Subnet Mask is 255.255.255.0. To connect AirStation to an existing LAN, specify the Subnet Mask that the LAN uses. If there’s more than one DHCP server o[...]
-
Seite 29
29 Advanced DHCP Settings This page offers the same DHCP settings as the previous one, and in addition, offers you the chance to change the Lease Period , De- fault Gateway , DNS servers , WINS serve r, and Domain Name . Click Apply when you have the settings the way you want them. To manually assign an IP address, click Manual Assignment .[...]
-
Seite 30
30 To manually link a LAN address to a MAC address, enter them under Add Client Infor- mation and click Add . Current DHCP Client Information shows all LAN addresses currently assigned by AirStation’s DHCP. You may congure a specic client to always recieve the same IP address by clicking Manual Assignment to the right of its MAC Address. Cl[...]
-
Seite 31
31 By default, the AirStation receives RIP (Route Information Protocol) informa- tion only from your local network, and doesn’t broadcast RIP at all. For large, complicated network congurations, you may wish to modify this behavior. Click Apply when you have your desired conguration. Lower on the page, routing information is displayed. Clic[...]
-
Seite 32
32 To congure a route manually, enter its Destination Address and Gateway . Enter a maximum number of hops allowable in Metric and click Add . Network Configuration (Edit Routing Information)[...]
-
Seite 33
33 NAT You may disable Network Address Translation and IPsec passthrough by unchecking the appropriate Enable boxes. If you have a DMZ, enter its IP address in the IP Address of DMZ box. Incoming packets containing no recognizable destination port information will be redirected to the DMZ’s IP address. Click Apply when done. To set a NAT table en[...]
-
Seite 34
34 NAT (Manual Entry) From this page you may manually add entries into the Address Translation Table. Click Add New Group when each is complete.[...]
-
Seite 35
35 Your AirStation comes pre-congured with basic rules. You may choose which of these to use by clicking on Add/Delete Basic Rules and turning to page 36. To make a custom rule, click on Congure IP Filter (page 37). IP Filter[...]
-
Seite 36
36 Get here by clicking on Add/Delete Basic Rules (see page 35). You may choose which of AirStation’s precongured basic rules are enabled or disabled. Active rules are displayed with a green background, and disabled rules are shown in red. Choose the rules you want to use by clicking under Operation . When your choices are complete, click on I[...]
-
Seite 37
37 Clicking on Congure IP Filter from the IP lter page (page 35) will bring you to this page, where you can make your own rules. Click Add Rule when you have each rule congured the way you want it. IP Filter (Configure IP Filter)[...]
-
Seite 38
38 Network Configuration (Intrusion Detector) To enable intrusion detector, choose Enable or Enable (Apply packet lter rules) from the Intrusion Detector drop-down box. If packet lter rules are applied, packets will be ltered with packet lter rules before Intrusion Detector is applied. Blocking IP spoong blocks packets from devices u[...]
-
Seite 39
39 You may disable Universal Plug and Play functionality by unchecking Enable here. Note that Windows (MSN) Messenger will not function correctly with UPnP disabled. UPnP[...]
-
Seite 40
40 Clicking Start AOSS Sequence has the same function as pushing the AOSS button on the router: it initiates the AOSS process. If all your clients support AOSS, it’s very simple to set them up. Press the AOSS button on the router, or the one on this page, and then push the AOSS button on the client device. Each client device will have to be set u[...]
-
Seite 41
41 If you have a mixed mode network, with both 802.11b and 802.11g clients, it’s recommended that you check 11g protection to ensure that slower 11b clients don’t hog all available bandwidth. Choosing Auto for Wireless mode lets both 802.11b and 802.11g clients connect to the network. If you would prefer to allow only one or the other, you have[...]
-
Seite 42
42 Buffalo recommends that you choose the strongest form of encryption that’s supported by all your client devices. • WEP is a lot better than nothing, and almost every wireless device ever made supports it. • TKIP is slower than WEP but much more secure. • AES is the most secure of all, and the quickest as well. Use it if you can. Setting [...]
-
Seite 43
43 To setup a bridge between two or more wireless access points, select Enable and click on Apply . For more on setting up WDS, see page 67, or click on Help at the top right corner of the screen. Bridge/Repeater (WDS Bridging)[...]
-
Seite 44
44 MAC Access Limit You may limit access to your wireless network to specic computers. Computers not listed on your MAC Registration List will not be able to connect to the network. If you enable this, click Edit Registration List to add MAC addresses to your registration list.[...]
-
Seite 45
45 MAC Access Limit (Edit Registration List) Advanced Settings Enter a MAC address and click Apply for each client that’s going to be accessing the network.[...]
-
Seite 46
46 Here, you can change your AirStation’s name on your network and the administrator password. The name of the administrator account is xed as “root”. If you have many AirStations on your network, having clear, descriptive names for each can make them much easier to administrate. Admin Configuration (Name/Password)[...]
-
Seite 47
47 You may set the time and date on your AirStation by entering it manually, and then clicking Apply . You may also click Acquire Current Time from your PC to set time and date automatically to match the PC you’re using to set it up. If you have an NTP time server on your network, Enable NTP functionality and enter your NTP Server Name . Choose h[...]
-
Seite 48
48 If you have a syslog server on your network, you may send logs to it. Check Enable to have logs transferred. Enter the address of your Syslog Server, check the logs you want transferred, and click Apply . Syslog Transfer[...]
-
Seite 49
49 Once your AirStation’s congured the way you want it, you can save the conguration here. You’ll need the current administrator password to restore the conguration from the backup le later. Click Help at the top right corner of the page for more information on backing up and recovering system conguration les. Save/Load Config[...]
-
Seite 50
50 Click Restart Now to restart your AirStation. Click Initialize Now to restore your AirStation to factory defaults and restart it. You may also initialize your AirStation by holding down the Init button on the bottom of the router for 3 seconds. Initialize/Reboot[...]
-
Seite 51
51 Click Browse to select your rmware update le. Then, click the Firmware Update button to update rmware. Firmware Update may take several minutes to complete. Do not power down the router until Firmware Update is nished and the diag light on the front of the router has stopped blinking. When available, updated rmware may be download[...]
-
Seite 52
52 The System Information page lists all the setup information for your AirStation. It can be very handy for setting up clients that don’t support AOSS. System Information[...]
-
Seite 53
53 Here you can choose what information gets logged and see recent log entries. Log Information[...]
-
Seite 54
54 Here, you can see the packets and errors for each of your networks. Packet Traffic Information[...]
-
Seite 55
55 Client Monitor shows you a list of all clients currently connected to the wireless network. Client Monitor[...]
-
Seite 56
56 To perform a Ping test, enter a target (such as 192.168.11.2 or www. buffalotech.com ) and click Execute . Successful pings return “64 bytes from . . .” messages. If the ping returns “Connection failed” or other errors, something is preventing you from communicating successfully with your target. Ping Test[...]
-
Seite 57
57 Connecting to a Preexisting Network Add an AirStation without changing your existing LAN configuration 1. Set the AirStation into Access Point Mode by moving the switch on the bottom from AUTO to BRI . 2. Connect one of the AirStation’s LAN ports to an existing router or switch on your network. Nothing should be plugged into the WAN port. 3. O[...]
-
Seite 58
58 The WHR-HP-G54’s external antenna will usually give the best performance if oriented to point straight up. If your AirStation is resting on its side, use the antenna’s swivel and twist function to orient it pointed upward. In some environments it’s desirable to further increase range by installing an external, higher-gain antenna. External[...]
-
Seite 59
59 For more information, FAQ’s, and updates, consult the AirStation website at http://www.buffalotech.com . WHR-HP-G54 AirStation Specifications Physical Specications Dimensions 1.1 x 5.1 x 5.7 in. (28 x 130 x 144mm) Weight 9.8 oz. lb. (277g) Temperature & Humidity Operation 0˚ to 40˚ C Maximum humidity 80% Transit/Storage 0˚ to 40˚ C [...]
-
Seite 60
60 Regulatory Information Wireless communication is often subject to local radio regulations. Although AirStation wireless networking products have been designed for operation in the license-free 2.4 GHz band, local radio regulations may impose limitations on the use of wireless commu- nication equipment. Network Compatability IEEE802.11g/b Standar[...]
-
Seite 61
61 11 selectable channels (3 non-overlapping) Modulation Technique Direct Sequence Spread Spectrum • ODFM for High Transmit Rate • DQPSK for Standard Transmit Rate • DBPSK for Low Transmit Rate Spreading 11-chip Barker Sequence Nominal Output Power: 19dBm (802.11b), 16dBm (802.11g) Transmit Rate: • High Speed 54 Mbps (125 Mbps in 125* High [...]
-
Seite 62
62 Semi-Open Ofce Environment 50 m (165 ft.) 70 m (230 ft.) 90 m (300 ft.) 115 m (375 ft.) Closed Ofce 25 m (80 ft.) 35 m (115 ft.) 40 m (130 ft.) 50 m (165 ft.) Receiver Sensitivity -83 dBm -87 dBm -91 dBm -94 dBm (depends on data rate) Delay Spread (at FER of <1%) 65 ns 225 ns 400 ns 500 ns (depends on data rate) • The range of wireles[...]
-
Seite 63
63 Note: The range values listed in Table “Radio Characteristics” are typical distances as measured at Buffalo Technology AirStation laboratories. These values are provided for your guidance but may vary according to the actual radio conditions at the location where the AirStation product is installed. AirStation IEEE 802.11 Channel Sets The ra[...]
-
Seite 64
64 Common Problems • Out of range, client cannot connect to the AirStation. • Conguration mismatch, client cannot connect to the AirStation. • Absence or conict with the Client Driver. • Conict of another device with the AirStation hardware. LED Activity Monitoring LED activity helps identify problems. • Power LED should be Green[...]
-
Seite 65
65 DIAG LED Activity Table DIAG LED Display Time Description/Action Continuous Red Starting RAM Error Red ash, 2 times Starting Flash ROM Error Red ash, 3 times Starting A problem on the wired LAN side Red ash, 4 times Starting A problem on the wireless LAN side LEDs Work But Client PC Cannot Connect to Network If the LEDs indicate that th[...]
-
Seite 66
66 • If the wireless adapter protocol is not yet installed, click the Add button and select the TCP/IP protocol from the list. Refer to Windows Help for more information. • If the wireless adapter protocol is installed, select the protocol and click the Properties button. Verify that the parameters match the settings provided by your LAN Admini[...]
-
Seite 67
67 Your AirStation’s WDS bridging capability allows you to extend the size of your wireless network by adding additional AirStations, all connected wirelessly. In this simple example, we’ll connect two AirStations in a wireless bridge. You may use these same steps to add additional bridges for greater coverage. * For easiest conguration, we [...]
-
Seite 68
68 Connect a PC’s Ethernet port to another RJ-45 port on the main router (the rst AirStation). You will use this PC to congure the settings of the AirStations. Here’s the whole setup, ready for initial conguration. * Note: Each AirStation may be part of 6 different bridges. Remember that each layer of bridges takes about half your tota[...]
-
Seite 69
69 Once the AirStations are powered on, you will want to make sure that they are in factory default conguration. On the bottom of each, hold down the “INIT” button for three seconds. This will reset them to factory defaults. They will take 30-60 seconds to reboot afterwards. Power on your PC. Make sure that it is congured to “obtain an [...]
-
Seite 70
70 The Web-Based Conguration Utility for your rst AirStation will open. Click on the Advanced tab. On the left side menu, click on Wireless Cong , and then Basic . Change the Wireless Channel from Auto to a channel. Make a note of the channel that you’ve chosen, because all of your wireless devices will need to be congured to use this[...]
-
Seite 71
71 On the left-side menu, click on Wireless Cong , and then Repeater . Repeater-Bridge (WDS) must be set to Enable . If it is not, change it to Enable in the drop down menu and click Apply . After the AirStation reboots, the screen will refresh. Click Edit Registered WDS Partners . Under Add New WDS Partner Access Point , enter the wireless MAC [...]
-
Seite 72
72 Now, you need to congure the second AirStation with the MAC address of the rst one. In your browser’s address eld, enter “192.168.11.100”. This will take you into the Web-Based Conguration Utility for the second AirStation. Once again, the username is “root” and the password is blank. Configuring a WDS Bridge[...]
-
Seite 73
73 In the Web-Based Conguration Utility, click on the Advanced tab, select Wireless Cong , and choose Basic . Change the wireless channel to match the one you set for the rst AirStation. Change Framebursting from 125 High Speed Mode to Framebursting or Do not use (whichever you chose for the rst AirStation). For easy roaming, you may ch[...]
-
Seite 74
74 Under Add New WDS Partner Access Point , enter the wireless MAC address of the rst AirStation (available from the bottom of the rst AirStation), with each pair of digits separated by a colon, e.g. MAC:000D0B10F779 would be entered 00:0D:0B:10:F7:79. Click New Partner when done. The AirStation will reboot, and when the screen refreshes, the[...]
-
Seite 75
75 Once you can connect to each of your access points, you should congure WEP encryption. Without WEP, anyone within range of your access points can easily connect to your network. From within the second AirStation’s Web-Based Conguration Utility (192.168.11.100), click on Advanced , then Wireless Cong , then Security . Note that you mus[...]
-
Seite 76
76 Hexadecimal Input - 26 digits (Hex WEP128 104 bit, key should contain 26 characters A-F, 0-9) Hexadecimal Input - 10 digits (Hex WEP64 40 bit, key should contain 10 characters A-F, 0-9) Enter at least one encryption key in the rst encryption key space. The key should match the format of the chosen WEP encryption type. Additional keys may be e[...]
-
Seite 77
77 Most problems with setting up WDS are caused by incorrectly entering the MAC addresses into each AirStation’s Web-Based Conguration Utility. If you’re having problems, check the MAC address settings in both AirStations’s Web-Based Conguration Utilities. Each Airstation should be congured to be in a bridge with the other’s wirele[...]
-
Seite 78
78 Notes on WDS: 1. All wireless access points in the wireless bridge need to support WDS. At time of publication, only Buffalo G54 and Apple Airport Extreme access points support WDS. 2. No single access point can communicate with more then six other access points in the wireless bridge. 3. Start the wireless bridge system with only two access poi[...]
-
Seite 79
79 10BaseT: 802.3 based Ethernet network that uses UTP (Unshielded twisted pair) cable and a star topology. 10 Mbps data tansmission speed. 100BaseT: 802.3 based Ethernet network that uses UTP (Unshielded twisted pair) cable and a star topology. 100 Mbps data tansmission speed. 1000BaseT: 802.3 based Ethernet network that uses UTP (Unshielded twist[...]
-
Seite 80
80 Destination Address: The address portion of a packet that identies the intended recipient station. DHCP (Dynamic Host Conguration Protocol): Based on BOOTP, it uses a pool of IP addresses, which it assigns to each device connected to it, and retrieves the address when the device becomes dormant for a period of time. DNS (Domain Name System[...]
-
Seite 81
81 Full-Duplex: To transmit on the same channel in both directions simultaneously. Half-duplex: To transmit on the same channel in both directions, one direction at a time. Hub: A device which allows connection of computers and other devices to form a LAN. IEEE (Institute of Electrical and Electronics Engineers): The professional organization which[...]
-
Seite 82
82 PCMCIA (Personal Computer Memory Card International Association) Card: Removable module that adds features to a portable computer. Peer-to-peer: This simple network is formed by connecting computers directly, without use of routers or hubs. A crossover cable is plugged into an Ethernet port in each computer, connecting them directly. Ping (Packe[...]
-
Seite 83
83 PPPoE (Point-to-Point Protocol over Ethernet): A specication for connecting users on an Ethernet line to the Internet through a common broadband medium. Protocol: A standard way of exchanging information between computers. RADIUS (Remote Authentication Dial In User Service): A server that issues authentication keys to clients. RAM (Random Acc[...]
-
Seite 84
84 SNMP (Simple Network Management Protocol: An application layer protocol that outlines the formal structure for communication among network devices. Static IP Address: A permanent IP address is assigned to a node in a TCP/IP network. Also known as global IP. STP (Shielded Twisted Pair): Twisted Pair cable wrapped in a metal sheath to provide extr[...]
-
Seite 85
85 WEP (Wired Equivalent Privacy): A security protocol for wireless local area networks dened in the 802.11b standard, using a 64 bit or 128 bit key. WEP was designed to provide the same level of security as that of a wired LAN. However, it has been found that WEP is not as secure as once believed. Web Browser: A software program that allows vie[...]
-
Seite 86
86 Notice This equipment has been tested and found to comply with the limits for a Class B digital devic e, pursua nt to part 15 of the FCC Rules. These limits are desig ned to provid e reasona ble pro te ct io n again st har mf ul int erf er en ce in a resi de nti al ins ta ll ati on .T hi s equi pme nt gen er at es, uses and can radiate radio fre[...]
-
Seite 87
87 equipment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65. This equipment should be installed and operated with at least 20cm and more between the radiator and person’s body (excluding extremities: hands, wrists, feet and legs). This transmitter must not be co-located or operating in conjunction with any oth[...]
-
Seite 88
88 Warranty Information Buffalo Technology (Melco Inc.) products come with a two-year limited warranty from the date of purchase. Buffalo Technology (Melco Inc.) warrants to the original purchaser the product; good operating condition for the warranty period. This warranty does not include no n-B u ff al o Tech no lo gy (Me lc o Inc. ) ins ta ll ed[...]
-
Seite 89
89 Contact Information Buffalo Technology (USA), Inc. 4030 West Braker Lane, Suite 120 Austin, TX 78759-5319 GENERAL INQUIRIES Monday through Friday 8:30am-5:30pm CST Direct: 512-794-8533 | Toll-free: 800-456-9799 | Fax: 512-794-8520 | Email: sales@buffalotech.com TECHNICAL SUPPORT North American Technical Support by phone is available 24 hours a d[...]
-
Seite 90
90 Buffalo Technology (Europe), Inc. 176 Buckingham Avenue, Slough, Berkshire, SL1 4RD United Kingdom GENERAL INQUIRIES Email: sales@buffalo-technology.com TECHNICAL SUPPORT Technical Support in Europe is available between the hours of 9am-6pm (GMT) Monday to Thursday and 9am-4:30pm (GMT) Friday for this product. Customers in Europe can obtain Tech[...]
-
Seite 91
91 * When operating in High-Speed Mode, this Wi-Fi device achieves an actual throughput of up to 34.1 Mbps, which is equivalent to the throughput of a system following 802.11g protocol and operating at a signaling rate of 125 Mbps. 125* High Speed Mode[...]