Cabletron Systems CSX200 Bedienungsanleitung

CSX200 CyberSWITCH Installation Guide 9032753 2012 01[...]

[...]

CSX200 Installation Guide i Notice Cabletron Systems reserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult Cabletron Systems to determine whether an y such changes hav e been made. The hardware, firmware, or software described in this manu[...]

Notice ii CSX200 Installation Guide VCCI Notice This is a Class A product based on the standard of the V oluntary Control Council for Interference by Information T echnology Equipment (VCCI). If this equipment is used in a domestic en vironment, radio disturbance may arise. When such trouble occurs, the user may be required to take correcti ve acti[...]

Notice CSX200 Installation Guide iii Exclusion of Warranty and Disclaimer of Liability 1. EXCLUSION OF W ARRANTY . Except as may be specifically provided by Cabletron in writing, Cabletron makes no warranty, expressed or implied, concerning the Program (including its documentation and media). CABLETR ON DISCLAIMS ALL W ARRANTIES, OTHER THAN THOSE S[...]

Notice iv CSX200 Installation Guide Declaration of Conformity Application of Council Directiv e(s): 89/336/EEC 73/23/EEC 91/263/EEC Manufacturer’ s Name: Cabletron Systems, Inc. Manufacturer’ s Address: 35 Industrial Way PO Box 5005 Rochester, NH 03867 European Representativ e Name: Mr. J. Solari European Representativ e Address: Cabletron Syst[...]

CSX200 Installation Guide v Contents CHAPTER 1 INTRODUCTION Related Documentation ................................................................................... 1-1 How to Use This Guide .................................................................................... 1-1 Document Conventions ................................................[...]

Contents vi CSX200 Installation Guide CHAPTER 3 10B ASE-T LAN REQUIREMENTS Network Requirements .................................................................................... 3-1 10BASE-T Twisted Pair Network .............................................................. 3-1 Port Descriptions ..................................................[...]

Contents CSX200 Installation Guide vii Status 1 (STS1) LED is AMBER ................................................................ 5-7 Status 1 (STS1) LED is GREEN ................................................................. 5-7 Status 2 (STS2) LED is OFF ...................................................................... 5-8 Status 2 (ST[...]

Contents viii CSX200 Installation Guide APPENDIX C FCC P ART 68 - USER’ S INFORMATION FOR CSX200 APPENDIX D GLOSSARY INDEX[...]

CSX200 Installation Guide 1-1 1 Intr oduction W elcome to the Cabletron Systems CSX200 CyberSWITCH Installation Guide . This guide provides configuration information, hardw are specifications and troubleshooting tips for the CSX200 CyberSWITCH. This guide also pro vides background information about 10BASE-T Ethernet Local Area Networks (LANs) and[...]

Chapter 1: Introduction 1-2 CSX200 Installation Guide Chapter 5 , Troubleshooting , sho ws ho w to use the LANVIEW LEDs on the CSX200 for network troubleshooting. Appendix A , WPIM Cable Specifications , provides part numbers and connector information for WPIMs (W ide Area Port Interface Modules). Appendix B , Specifications and Standards Complianc[...]

Document Conventions CSX200 Installation Guide 1-3 Document Con ventions The follo wing con ventions are used throughout this guide: NO TE Note symbol. Calls the reader’ s attention to any item of inf or mation that ma y be of special impor tance. TIP Tip symbol. Conv eys helpful hints concerning procedures or actions. ! CA UTION Caution symbol. [...]

Chapter 1: Introduction 1-4 CSX200 Installation Guide Getting Help If you need additional support related to this de vice, or if you hav e any questions, comments, or suggestions concerning this manual, contact the Cabletron Systems Global Call Center: Before calling the Cabletron Systems Global Call Center , have the follo wing information ready: [...]

CSX200 Installation Guide 2-1 2 About the CSX200 The CSX200 CyberSWITCH ( Figure 2-1 ) is an access de vice that provides Ethernet Local Area Network (LAN) connecti vity (via twelve RJ45 ports) for the small office, and of fers high-speed W ide Area Network (W AN) access to a remote site, such as the Internet or an enterprise network. The CSX200 s[...]

Chapter 2: About the CSX200 2-2 CSX200 Installation Guide • The WPIM-SY provides a synchronous serial connection of up to 2.048 Mbps to e xternal communications equipment (e.g., a multiplex er or CSU/DSU). The WPIM-Sync uses a subminiature 26-pin connector that supports the electrical signal interfaces listed belo w . Appendix A , WPIM Cable Spec[...]

Remote Management Capabilities CSX200 Installation Guide 2-3 P olarity Detection and Correction — Each twisted pair port on the CSX200 incorporates a Polarity Detection and Correction feature that allo ws the CSX200 to pass data regardless of the polarity of the twisted pair segment’ s receive link. W e do not recommend operating in this condit[...]

Chapter 2: About the CSX200 2-4 CSX200 Installation Guide CSX200 Firmware Suppor t The CSX200 firmware supports IEEE 802.1d bridging, and IP and IPX routing,. W ide Area Networking includes P oint-to-Point Pr otocol (PPP) , and Frame Relay . Remote access is via Full or Fractional T1, E1, Synchronous, Digital Data Service, ISDN, or HDSL connection[...]

CSX200 Firmware Support CSX200 Installation Guide 2-5 Firmware Data Compression The ST A C Electronics Stacker LZS Compression algorithm provides a minimum of 2:1 firmw are data compression for the CSX200 ov er PPP and Frame Relay . Firmware data compression is supported in software on each W AN interface for line speeds of up to 256 Kbps per WPIM[...]

Chapter 2: About the CSX200 2-6 CSX200 Installation Guide This is done to replace the hidden local IP addresses from the sub network with one or more public InterNic assigned IP addresses that can be sent ov er the outside network on the W AN interfaces. Once the CSX200 is assigned at least one public IP address, ov er 250 IP clients can share this[...]

CSX200 Firmware Support CSX200 Installation Guide 2-7 The ANSI standard defines a mechanism for the network to signal the e xistence of congestion, called Explicit Congestion Notification (ECN) bits. Frame Relay uses FECN (Forw ard ECN) and BECN (Backward ECN) bits to notify end user de vices about network congestion. Although the Frame Relay Pro[...]

Chapter 2: About the CSX200 2-8 CSX200 Installation Guide Full-duplex operation places an additional step to half-duple x operation that mirrors the operation for a peer to v alidate the authenticator . The peer de vice challenges the authenticator by generating a CHAP challenge, and the authenticator returns a CHAP response. The peer de vice chall[...]

CSX200 Firmware Support CSX200 Installation Guide 2-9 The CSX200 supports one ISDN BRI line and either or both of the B channels for transferring data. If the two B channels are used for separate connections, each pro vides up to 64 Kbps transfer rate. Both channels can be used together to provide uncompressed data transfer at up to 128 Kbps. The C[...]

Chapter 2: About the CSX200 2-10 CSX200 Installation Guide In transparent bridging, the decision to forward the frame is based on this comparison. If the address indicates that the sending station and the destination station are on the same side of the bridge, the frame is not forwarded across the bridge. If the addresses do not indicate that, the [...]

CSX200 Firmware Support CSX200 Installation Guide 2-11 The CSX200 uses the Spanning T ree Algorithm to pre v ent data loops and duplicate data. This is a self-learning bridge, i.e., the bridge builds and updates an address table with each MA C source address and associated information when the packets are recei ved. IP Routing — IP routing suppor[...]

Chapter 2: About the CSX200 2-12 CSX200 Installation Guide System P assw ords Y ou can control access to the CSX200 by the use of three passwords. Each password pro vides a dif ferent le vel of access to the CSX200. The default password for each access le vel is pre-set to public. The follo wing definitions explain the le vels of access: read-only[...]

CSX200 Firmware Support CSX200 Installation Guide 2-13 • Frame Relay DTE MIB RFC1490 • Security MIB RFC1472 (CCP , P AP , and CHAP) • RS-232 MIB RFC1317 • LQM MIB RFC1989 • PPP MP MIB RFC1990 • Frame Relay Multi Protocol Encapsulation MIB RFC1490 SNMP T rap Support SNMP T raps are notifications of network e vents sent by an SNMP-compli[...]

Chapter 2: About the CSX200 2-14 CSX200 Installation Guide IP Events, continued: • IP has detected Link UP on interface # • IP has detected Link DO WN on interface # • IP Primary address has been changed on interface # • IP Secondary address has been changed on interface # • IP Access Control Lists hav e been enabled on interface # • IP[...]

CSX200 Firmware Support CSX200 Installation Guide 2-15 • IPX has detected Port UP (W AN de vices only) • IPX has detected Port DO WN (W AN devices only) • IPX RIP has been enabled on interface # • IPX RIP has been disabled on interface # • IPX SAP has been enabled on interface # • IPX SAP has been disabled on interface # Software and Fi[...]

Chapter 2: About the CSX200 2-16 CSX200 Installation Guide[...]

CSX200 Installation Guide 3-1 3 10B ASE-T LAN Requirements This chapter contains general networking guidelines for setting up a 10B ASE-T Local Area Network using ports 1 through 12 on the CSX200. Re view the requirements and specifications outlined in this chapter before attempting to install the CSX200. Netw ork Requirements T ake care in planni[...]

Chapter 3: 10BASE-T LAN Requirements 3-2 CSX200 Installation Guide T emperature — Multi-pair PVC 24 A WG telephone cable typically has an attenuation of approximately 8–10 dB/100 m at 20°C (68°F). The attenuation of PVC insulated cable v aries with temperature. At temperatures greater than 40°C (104°F), use plenum-rated cable to ensure that[...]

10BASE-T LAN Configuration CSX200 Installation Guide 3-3 10B ASE-T LAN Configuration This section contains the procedures for connecting a UTP segment from the 10B ASE-T network or other de vices to the CSX200. Ports 1 through 12 on the CSX200 hav e RJ45 connectors for UTP connections. Connecting UTP Cables to P orts 1 Through 12 Before connecting[...]

Chapter 3: 10BASE-T LAN Requirements 3-4 CSX200 Installation Guide 3. Verify that a Link exists by checking that the receive port ( RCV) LED is on (flashing green or amber or on solid green). If the RCV LED is off, perform the following steps until it is on: a. Check that the 10B ASE-T device at the other end of the twisted pair segment is ON and c[...]

CSX200 Installation Guide 4-1 4 Installation This chapter sho ws you ho w to connect your CSX200 to the network. Ensure that the network meets the guidelines and requirements outlined in Chapter 3 , 10BASE-T LAN Requirements , before installing your CSX200. Unpac king the CSX200 Remov e the shipping material from the box and carefully remov e the C[...]

Chapter 4: Installation 4-2 CSX200 Installation Guide Remo ving the CSX200 Co ver The cov er must be remov ed to install a W AN Port Interf ace Module. T o remove the chassis co ver , proceed as follows: • If the CSX200 is installed, unplug the po wer cord from the rear of the CSX200 chassis. • Disconnect all network cables attached to the CSX2[...]

Installation Guidelines CSX200 Installation Guide 4-3 Figure 4-1 Removing the Plastic Chassis Co ver Installing a WPIM T o install a WPIM into the CSX200, refer to Figure 4-2 on the follo wing page. ! CA UTION Bef ore perf orming installation procedures, ensure that the requirements outlined in the section, Tabletop and Shelf Installations on page [...]

Chapter 4: Installation 4-4 CSX200 Installation Guide Figure 4-2 Installing WPIMs T o install a WPIM, follo w these instructions: • Attach the disposable grounding strap to your wrist (refer to the instructions outlined on the disposable grounding strap package). • Remov e the CSX200 cov er (see Removing the CSX200 Cover on page 4-2). • Remov[...]

COMP/ENCR Module Installation CSX200 Installation Guide 4-5 COMP/ENCR Module Installation T o install the CSX200-COMP/ENCR into the CSX200 chassis, perform the following procedure: • Attach one end of the antistatic wrist strap to your wrist and the other end to an approv ed electrical ground. • Unpack the CSX200-COMP/ENCR by carefully removing[...]

Chapter 4: Installation 4-6 CSX200 Installation Guide Figure 4-3 CSX200-COMP/ENCR Module Installation Installing the CSX200 The CSX200 may be installed on a tabletop, on a shelf, or in a 19-inch rack. T abletop and Shelf Installations The follo wing two subsections pro vide guidelines for installation on a tabletop or shelf. T o install the CSX200 [...]

Rackmount Installation CSX200 Installation Guide 4-7 Figure 4-4 T abletop or Shelf Installation Rac kmount Installation Cabletron Systems of fers an accessory kit that includes rackmount brackets, mounting scre ws, and a strain-relief bracket for cable management. The accessory kit is not included with the CSX200, but can be purchased separately fr[...]

Chapter 4: Installation 4-8 CSX200 Installation Guide Materials Required The follo wing parts are included in the CSX200-A CCY -KIT . • Strain-relief bracket (sho wn in Figure 4-6 , on the follo wing page) • Left and right rackmount brackets (sho wn in Figure 4-7 , on the follo wing page) • 8-32 x 1/4-inch, pan-head scre ws (4) • 8-32 x 3/8[...]

Rackmount Installation CSX200 Installation Guide 4-9 Figure 4-6 Attaching the Strain-Relief Brac ket Attaching the Rac kmount Brackets Refer to Figure 4-7 , below, and proceed as follo ws to attach the rackmount brackets: • Locate the four 8-32 x 1/4-inch scre ws and the two rackmount brackets in the CSX200-A CCY -KIT package. • Using the four [...]

Chapter 4: Installation 4-10 CSX200 Installation Guide Installing the CSX200 in a 19-Inch Rac k Install the CSX200 in a 19-inch rack as follo ws: • Position the CSX200 between the vertical frame members of the 19-inch rack. • Fasten the CSX200 with mounting scre ws as shown in Figur e 4-8 , belo w . Figure 4-8 Installing the CSX200 in the Rack [...]

CSX200 Installation Guide 5-1 5 Tr oubleshooting Use this chapter in conjunction with the LANVIEW status monitoring and diagnostic LEDs on the CSX200 to diagnose po wer failures, collisions, cable faults and link problems. Figure 5-1 sho ws the front panel LEDs. T able 5-1 , T able 5-2 , T able 5-3 , T able 5-4 , and T able 5-5 describe LED states.[...]

Chapter 5: Troubleshooting 5-2 CSX200 Installation Guide T able 5-2 CSX200 LAN LED States LED Color State Receive (RCV) OFF Not receiving traffic AMBER (flashing) Receiving traffic Link (LNK) OFF Link does not e xist GREEN NORMAL, link e xists T able 5-3 CSX200 W AN LED States LED Color State T ransmit (XMT) OFF Not transmitting traffic GREEN ([...]

Troubleshooting CSX200 Installation Guide 5-3 T able 5-4 CSX200 W AN LED States for STS 1 WPIM Color State T1, DI, and E1 OFF Normal or por t disabled RED Red alarm DDS OFF Normal or por t disabled AMBER Out of ser vice (OOS) SYNC OFF Inactive or disab led GREEN Request to send (R TS) HDSL OFF P or t disabled or in loopbac k mode RED Loop 1 not syn[...]

Chapter 5: Troubleshooting 5-4 CSX200 Installation Guide T roub leshooting CSX200 Hard ware P ower (PWR) LED is OFF • Check that the po wer connection is firmly attached to the back panel of the CSX200, and the other end to an acti ve po wer source. Pr ocessor (CPU) LED is OFF If the CPU stays OFF for an extended amount of time, and the po wer ([...]

Troubleshooting the WAN CSX200 Installation Guide 5-5 T roub leshooting the W AN Link (LNK) LED is OFF The W AN interface is not configured for operation. • Use QuickSET or Local Management to make sure that the W AN interface is configured correctly . Link (LNK) LED is RED The W AN interface is configured, b ut there is no signal indicating t[...]

Chapter 5: Troubleshooting 5-6 CSX200 Installation Guide WPIM-SYNC Installed in CSX200 The port is operating normally . If it is not, and this LED is OFF the port may be disabled or R TS may be inacti ve. • Use QuickSET or Local Management to make sure that the W AN interface on the Local de vice is configured correctly . WPIM-HDSL Installed in [...]

Troubleshooting the WAN CSX200 Installation Guide 5-7 WPIM-HDSL Installed in CSX200 WPIM-HDSL is configured for either Full or Fractional T1 and the WPIM is not able to establish synchronization on Loop 1 with the remote HDSL circuit. • V erify using QuickSET of Local Management that one of the WPIM-HDSL is in v olved in the connection is set to[...]

Chapter 5: Troubleshooting 5-8 CSX200 Installation Guide WPIM-HDSL is installed in CSX200 The Port is operating normally , Loop 1 has synchronized with the HDSL circuit at the remote end. Status 2 (STS2) LED is OFF WPIM-T1, WPIM-E1, WPIM-DI, or WPIM-DDS Installed in CSX200 The port is operating normally . If it is not, and this LED is OFF the port [...]

Troubleshooting the WAN CSX200 Installation Guide 5-9 • V erify the use of proper cabling for the HDSL connections. Category 3 or Cate gory 5 Unshielded T wisted Pair copper wiring is required. One pair (2 wires) for Fractional T1, tw o pair (4 wires) for Full T1. The presence of bridged taps and multiple wire se gments connected together to form[...]

Chapter 5: Troubleshooting 5-10 CSX200 Installation Guide T est (TST) LED is AMBER (blinking) The de vice is in test mode. • The CSX200 is running its Po wer-up Diagnostic T ests. • Loopback T esting is underway on a W AN circuit. In vestigating Software Configuration Pr oblems Software problems usually occur when your software configuration [...]

Investigating Software Configuration Problems CSX200 Installation Guide 5-11 If TCP/IP Routing, • Check that TCP/IP Routing is set on and is enabled at the remote end. • Check that the IP address of the LAN beyond the remote router is correct, as well as the associated Subnet Mask. • If the remote router W AN IP address and Subnet Mask are re[...]

Chapter 5: Troubleshooting 5-12 CSX200 Installation Guide[...]

CSX200 Installation Guide A-1 A WPIM Cable Specifications WPIM-T1 This section provides the Cabletron Systems part number and connector specifications for WPIM-T1 interface cables. T able A-1 provides connector type and part number information. T able A-2 provides RJ48 connector pin assignments. NO TE F or all WPIM cab les, there is par t number [...]

Appendix A: WPIM Cable Specifications A-2 CSX200 Installation Guide T able A-3 provides RJ48 DTE pin assignments. T able A-4 provides RJ48 netw ork pin assignments. Table A-3 DTE Pin Assignments Pin Signal 1 Receive Ring 2 Receive Tip 3 Not Used 4 T ransmit Ring 5 T ransmit Tip 6 Not Used 7 Shield Ground 8 Shield Ground Table A-4 Network Pin Assign[...]

WPIM-SY CSX200 Installation Guide A-3 WPIM-SY This section provides the Cabletron Systems part number and connector specifications for the WPIM-SY interface cables. T able A-5 provides the cable and interf ace types, electrical types, and part numbers for the WPIM-SY . Table A-5 WPIM-SY Interface Cables Cable and Interface T ype Electrical T ype P[...]

Appendix A: WPIM Cable Specifications A-4 CSX200 Installation Guide EIA-449 T able A-6 sho ws the connector number , cable assembly description, and connector type. T able A-7 provides pin assignments for the EIA-449 interf ace cable. Table A-6 EIA-449 Interface Connector Number Cable Assemb ly Description Connector T ype 1 EIA-530A AL T A to EIA-4[...]

WPIM-SY CSX200 Installation Guide A-5 V .35 T able A-8 sho ws the connector number , cable assembly description, and connector type. T able A-9 provides pin assignments for the V .35 interface cable. CE DTE Ring Indicator 22 15 Incoming Call DTE IC TM T est Mode 25 18 T est Mode TM CC DCE Ready 6 11 Data Mode DM CD DCE DTE Ready 20 12 T erminal Rea[...]

Appendix A: WPIM Cable Specifications A-6 CSX200 Installation Guide DB DTE T ransmit Signal Timing A 15 E Y T ransmitter Signal Timing A DTE 114 T ransmit Signal Timing B 12 AA T ransmitter Signal Timing B DD Receive Signal Timing A 17 F V Receiver Signal Timing A 115 Receive Signal Timing B 9X Receiver Signal Timing B D A DCE T ransmit Signal Timi[...]

WPIM-SY CSX200 Installation Guide A-7 EIA-232 T able A-10 sho ws the connector number , cable assembly description, and connector type. T able A-11 provides pin assignments for the EIA-232 interf ace cable. Table A-10 EIA-232 Interface Connector Number Cable Assembly Description Connector T ype 1 EIA-530A AL T A to EIA-232 Sub DB 26-pin male 2 DB-2[...]

Appendix A: WPIM Cable Specifications A-8 CSX200 Installation Guide X.21 T able A-12 sho ws the connector number , cable assembly description, and connector type. T able A-13 provides pin assignments for the X.21 interf ace cable. Table A-12 X.21 Interface Connector Number Cable Assembly Description Connector T ype 1 EIA-530A AL T A to X.21 Sub DB [...]

WPIM-SY CSX200 Installation Guide A-9 EIA-530, EIA-530 AL T A, EIA-530 A, and EIA-530 A AL T A T able A-14 sho ws the connector number , cable assembly description, and connector type for the EIA-530, EIA-530 AL T A, EIA-530A, and EIA-530A AL T A, interface cables. T able A-15 provides the cable pin assignments for the EIA-530, EIA-530 AL T A, EIA-[...]

Appendix A: WPIM Cable Specifications A-10 CSX200 Installation Guide DB DTE T ransmit Signal Timing A 15 E 15 T ransmit Signal Timing A DTE DB T ransmit Signal Timing B 12 12 T ransmit Signal Timing B DD Receive Signal Timing A 17 F 17 Receive Signal Timing A DD Receive Signal Timing B 9 9 Receive Signal Timing B DA DCE T ransmit Signal Timing A 24[...]

WPIM-DDS CSX200 Installation Guide A-11 WPIM-DDS This section provides Cabletron Systems part number and connector specifications for the WPIM-DDS interface cable. The WPIM-DDS has one RJ45 port for a direct connection to a single Digital Data Service (DDS) circuit. T able A-16 provides cable and interf ace type, and part number information for th[...]

Appendix A: WPIM Cable Specifications A-12 CSX200 Installation Guide WPIM-E1 This section provides the Cabletron Systems part number and connector specifications for the WPIM-E1 interface cable. T able A-18 sho ws the WPIM-E1 connector number, cable and interf ace type, connector type and part number information. T able A-19 provides WPIM-E1 netwo[...]

WPIM-E1 CSX200 Installation Guide A-13 T able A-20 provides WPIM-E1 DTE interface cable pin assignments. T able A-21 provides WPIM-E1 RJ45 network interface cable pin assignments. Table A-20 DTE Interface Pin Signal 1 Receive Ring 2 Receive Tip 3 Shield Ground 4 T ransmit Ring 5 T ransmit Tip 6 Shield Ground 7 Not Used 8 Not Used Table A-21 Network[...]

Appendix A: WPIM Cable Specifications A-14 CSX200 Installation Guide WPIM-DI This section provides Cabletron Systems part number and connector specifications for the WPIM-DI interface cables. T able A-22 sho ws the connector number , cable assembly description, cable and interface type, connector type and part number information for the WPIM-DI in[...]

WPIM-HDSL CSX200 Installation Guide A-15 T able A-24 provides the WPIM-DI drop and insert interface cable pin assignments. WPIM-HDSL This section provides connector specifications for the WPIM-HDSL interface cables. T able A-25 provides pin assignments for the RJ-45 netw ork interface connector . Table A-24 WPIM-DI Drop and Insert Pin Signal 1 T r[...]

Appendix A: WPIM Cable Specifications A-16 CSX200 Installation Guide[...]

CSX200 Installation Guide B-1 B Specifications and Standar ds Compliance This chapter contains hardware specifications, and safety and compliance standards for the CSX200, and for the indi vidual WPIMs that can be configured with this de vice. Table B-1 Hardware Specifications W AN Interface CSX200 - One WPIM interface (WPIM not included) CSX201[...]

Appendix B: Specifications and Standards Compliance B-2 CSX200 Installation Guide CSX200 Regulatory Compliance Safety — This unit meets the safety requirements of UL 1950, CSA C22.2 No. 950 and EN 60950, IEC 950, and 73/23/EEC. Electroma gnetic Compatibility (EMC) — This unit meets the EMC requirements of FCC P art 15, EN 55022, EN 50082-1, 89/[...]

Individual WPIM Regulatory Compliance CSX200 Installation Guide B-3 WPIM-SY This section describes the en vironmental specifications and safety and approv al requirements for the WPIM-SY . Safety — This unit meets the safety requirements of UL1950, CSA C22.2 No. 950, EN 60950, IEC 950, and 73/23/EEC. EMI — This unit meets the EMI requirements [...]

Appendix B: Specifications and Standards Compliance B-4 CSX200 Installation Guide WPIM-E1 This section describes the en vironmental specifications and safety and approv al requirements for the WPIM-E1. Safety — This unit meets the safety requirements of EN 60950, IEC 950, 73/23/EEC and AS/NZS 3260. Electroma gnetic Compatibility (EMC) — This u[...]

CSX200 Installation Guide C-1 C FCC P ar t 68 - User’ s Inf ormation f or CSX200 The follo wing instructions are to ensure compliance with the Federal Communications Commission (FCC) Rules, Part 68: 1. All connections to the WPIM-T1, WPIM-DI and WPIM-DDS must be made using standard plugs and jacks. 2. Before connecting your unit, you must inform [...]

Appendix C: FCC Part 68 - User’s Information for CSX200 C-2 CSX200 Installation Guide 6. If the telephone company alters their equipment in a manner that will affect use of this device, they must give you advance warning so as to give you the opportunity for uninterrupted service. You will be advised of your right to file a complaint with the FCC[...]

FCC Part 68 - User’s Information for CSX200 CSX200 Installation Guide C-3 AFFIDAVIT FOR THE CONNECTION OFCUSTOMER EQUIPMENT TO 1.544 MBPS AND/OR SUBRATE DIGITAL SERVICES For the w ork to be performed in the certified territory of T elco’ s name: State of: Country of: I, , of (Name of Authorized Representative) (Customer Name) , (Customer’ s [...]

Appendix C: FCC Part 68 - User’s Information for CSX200 C-4 CSX200 Installation Guide I attest that the operator(s) maintainer(s) of the digital CPE responsible for the establishment, maintenance and adjustment of the encoded analog content and billing information has (hav e) been trained to perform these functions by successfully completing one [...]

CSX200 Installation Guide D-1 D Glossary 10B ASE-T — IEEE 802.3 standard for the use of Ethernet LAN technology ov er Unshielded T wisted Pair wiring, running at 10 Mbps. ARP — Address Resolution Protocol. An Internet protocol used to bind an IP address to Ethernet/ 802.3 addresses. ASCII — American Standard Code for Information Interchange. [...]

Appendix D: Glossary D-2 CSX200 Installation Guide DHCP — Dynamic Host Configuration Protocol is a protocol for automatic TCP/IP configuration that provides static and dynamic address allocation and management. Dial on Demand — Dial up W AN resources are accessed only when remote access is required and released as soon as the resource is no l[...]

Glossary CSX200 Installation Guide D-3 ISDN — Integrated Services Digital Netw ork. Digital transmission standard defining communication protocols permitting telephone networks to carry data, v oice, fax and other streams. Leased Line — A telecommunications line between two service points leased from a communications carrier for pri v ate use,[...]

Appendix D: Glossary D-4 CSX200 Installation Guide OSI — Open System Interconnection. An international standard de veloped by ITU (formally CCITT) and ISO (International Organization for Standardization) to f acilitate data networking multi-vendor interoperability . The OSI Reference Model defines se ven layers, each providing specific network [...]

Glossary CSX200 Installation Guide D-5 SNMP — Simple Network Management Protocol. A widely implemented Internet network management protocol that allo ws status monitoring, getting/setting of parameters for configuration and control of network de vices, such as routers and bridges. Split B Channels — Each 64 Kbps ISDN B-channel can be used indi[...]

Appendix D: Glossary D-6 CSX200 Installation Guide W atchdog Frames — Frames sent out by servers to clients, under IPX, to v erify that clients are still logged on. Wide Area Network — A communications netw ork that is geographically dispersed thus requiring links provided by communications carriers. W orkstation — Computer or terminal used b[...]

CSX200 Installation Guide Index-1 Index Numerics 10B ASE-T connection 3-3 impedance 3-1 length 3-1 requirements 3-1 temperature 3-2 B Bridge filtering 2-11 Bridging 2-9 Bridging and routing 2-10 C Cable specifications 10BASE-T UTP 3-1 Challenge Handshake Authentication Protocol (CHAP) 2-7 COMP/ENCR installation 4-5 D Daughter Board 2-3 Dynamic Ho[...]

Index Index-2 CSX200 Installation Guide R Rack Mounting accessory kit 2-3 Remote Network Management 2-3 Routing 2-10 S Safety Requirements B-3 SNMP 2-12 SNMP Community Names read-only 2-12 read-write 2-12 super-user 2-12 Software and firmware upgrades 2-15 T technical support 1-3 T roubleshooting 5-1 bridging 5-10 power 5-4 software 5-10 TCP/IP ro[...]