Cadillac 2010 STS Bedienungsanleitung

2010 Cadillac STS Owner Manual M In Brief ................ .......... ........... ....... 1 - 1 I n s t r u m e n t P a n e l ... .............................. 1 - 2 Initial Drive Information . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 V ehicle Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-14 Performance [...]

2010 Cadillac STS Owner Manual M B u l b R e p l a c e m e n t ... ........................... 6 - 4 9 Windshield Replacement . . . . . . . . . . . . . . . . . . . . . . . . 6-50 Windshield Wiper Blade Replacement . . . . . . . . . . . 6-51 T i r e s ............. ................. .............. 6 - 5 2 Appearance Care . . . . . . . . . . . . . . [...]

GENERAL MOTORS, GM, the GM Emblem, CADILLAC, the CADILLAC Crest & Wreath, and the name STS are registered trademarks and the name STS-V is a trademark of General Motors LLC. This manual describes features that may or may not be on your specific vehicle either because they are options that you did not purchase or due to changes subsequent to the[...]

Safety W arnings and Symbols W arning messages found on vehicle labels and in this manual describe hazards and what to do to avoid or reduce them. Danger indicates a hazard with a high level of risk which will result in serious injury or death. W arning or Caution indicates a hazard that could result in injury or death. { W ARNING: These mean there[...]

V ehicle Symbol Chart Here are some additional symbols that may be found on the vehicle and what they mean. For more information on the symbol, refer to the index. 9 : Airbag Readiness Light # : Air Conditioning ! : Antilock Brake System (ABS) g : Audio Steering Wheel Controls or OnStar ® $ : Brake System Warning Light " : Charging System I :[...]

2 NOTES vi[...]

Section 1 In Brief Instrument Panel ................................... 1-2 Initial Drive Information .. ....... .................. 1-4 Remote Keyless Entry (RKE) System . . . . . . . . . . . 1-4 Remote Vehicle Start . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [...]

Instrument Panel 1-2[...]

A. Outlet Adjustment on page 4 ‑ 48 . B. Instrument Panel Brightness on page 4 ‑ 35 . DIC Operation and Displays on page 4 ‑ 70 . Head-Up Display (HUD) on page 4 ‑ 38 (If Equipped). C. T urn Signal/Multifunction Lever on page 4 ‑ 4 . Headlamps on page 4 ‑ 27 . Cruise Control on page 4 ‑ 12 . Adaptive Cruise Control on page 4 ‑ 15 (I[...]

Initial Drive Information This section provides a brief overview about some of the important features that may or may not be on your specific vehicle. For more detailed information, refer to each of the features which can be found later in this owner manual. Remote Keyless Entry (RKE) System The keyless access transmitter is used to lock and unlock[...]

When the vehicle starts, the parking lamps will turn on and remain on as long as the engine is running. The doors will be locked and the climate control system may come on. The engine will continue to run for 10 minutes. Repeat the steps for a 10-minute time extension. Remote start can be extended only once. Canceling a Remote Start T o cancel a re[...]

T runk T runk Lid Release There are three ways to open the trunk lid. . Press the V button located on the driver door . . Press V on the keyless access transmitter . . Squeeze the trunk release button located on the rear of the trunk lid above the license plate. See T runk on page 3 ‑ 15 for more information. Windows The power window switches are[...]

Seat Adjustment Power Seats The power seat controls are on the outboard side of the seat(s). Move the seat forward or rearward by moving the control (A) forward or rearward. Raise or lower the front or rear of the seat cushion by moving the front or rear of the control (A) up or down. See Power Seats on page 2 ‑ 2 . Power Reclining Seatbacks The [...]

Heated Seats (Front) On vehicles with heated front seats, the buttons are located on the climate control panel. z : Press the up or down arrow to turn on the heated seat at the highest or lowest setting. Press the up or down arrows a second time to raise or lower the setting. Press the down arrow until the indicator on the climate control displays [...]

Heated and V entilated Seats On vehicles with heated and ventilated seats, the buttons are located on the climate control panel. z : Press to heat the seat and seatback. { : Press to ventilate the seat. For more information see Heated and V entilated Seats on page 2 ‑ 4 Head Restraint Adjustment Do not drive until the head restraints for all occu[...]

Sensing System for Passenger Airbag The passenger sensing system will turn off the right front passenger frontal airbag under certain conditions. The driver airbag, seat ‐ mounted side impact airbags and the roof ‐ rail airbags are not affected by the passenger sensing system. The passenger airbag status indicator will be visible on the overhea[...]

The dimming feature automatically adjusts the driver outside mirror for the glare of the headlamps behind your vehicle. See Automatic Dimming Rearview Mirror on page 3 ‑ 37 for more information. Manually fold the mirrors inward to prevent damage when going through an automatic car wash. T o fold, push the mirror toward the vehicle. Push the mirro[...]

Interior Lighting Reading Lamps The reading lamps are located on the overhead console. These lamps come on automatically when any door is opened. For manual operation, press the button next to each lamp to turn it on or off. If the reading lamps are left on, they automatically shut off 10 minutes after the ignition has been turned off. For more inf[...]

; : T urns on the parking lamps and other lamps. 5 : T urns on the headlamps and other lamps. For more information, see: . Headlamps on page 4 ‑ 27 . . Daytime Running Lamps (DRL) on page 4 ‑ 32 . . Fog Lamps on page 4 ‑ 33 . Windshield Wiper/W asher The windshield wiper lever is on the right side of the steering column. Move the lever to sel[...]

Climate Controls The heating, cooling, and ventilation can be controlled for the vehicle with this system. V ehicles With Heated and V entilated Seats Shown, V ehicles Without Similar A. Driver and Passenger Side Power Buttons B. V entilated Seat C. AUTO D. Air Recirculation E. Air Conditioning F . Heated Seat G. Fan Control H. Defrost I. Rear Wind[...]

Setting Preset Stations Up to 30 stations (six FM1, six FM2, six AM, six XM1 and six XM2), can be programmed on the six numbered pushbuttons. T o program preset stations: 1. T une to a station and select the equalization, DSP , or PTY (program type) setting if desired. 2. Press and hold one of the six numbered pushbuttons for two seconds until a be[...]

Satellite Radio XM is a satellite radio service that is based in the 48 contiguous United States and 10 Canadian provinces. XM satellite radio has a wide variety of programming and commercial-free music, coast-to-coast, and in digital-quality sound. A fee is required to receive the XM service. For more information, refer to: . www .xmradio.com or c[...]

y z : Press to go to the next or previous radio station stored as a favorite or tack on a CD. + e − : Press to increase or to decrease the volume. b g : Press and release to silence the vehicle speakers only . Press and release again to turn the sound on. For vehicles with Bluetooth ® , OnStar ® , or a navigation system, press and hold to inter[...]

Driver Information Center (DIC) The DIC display is located at the bottom of the instrument panel cluster . It shows the status of many vehicle systems. Without Head-Up Display (HUD) With Head-Up Display (HUD) The DIC buttons are located on the instrument panel, to the left of the steering wheel. « 4 ª : Press to scroll through the available vehic[...]

V ehicle Personalization Some vehicle features can be programmed by using the buttons on the remote keyless access transmitter and the buttons on the audio system. The features that can be programmed include: . Driver Greeting . Key Fob Reminder . Remote Start . Memory Features . Lock and Unlock Feedback . Lighting Features . Door Lock and Unlock S[...]

Power Outlets Accessory power outlets can be used to plug in electrical equipment, such as a cellular telephone. The vehicle has one outlet in front of the center console, one in the center console lid and there may be an additional outlet in the rear of the center console. See Accessory Power Outlet(s) on page 4 ‑ 42 . Performance and Maintenanc[...]

Tire Pressure Monitor This vehicle may have a T ire Pressure Monitor System (TPMS). The T ire Pressure Monitor alerts you when a significant reduction in pressure occurs in one or more of the vehicle ’ s tires by illuminating the low tire pressure warning light on the instrument cluster . The warning light will remain on until the tire pressure i[...]

Resetting the Oil Life System 1. Press the up or down arrow to scroll the DIC to show OIL LIFE. 2. Once the XXX% ENGINE OIL LIFE menu item is highlighted, press and hold the RESET button until the percentage shows 100%. If the percentage does not return to 100% or if the CHANGE ENGINE OIL SOON message comes back on when the vehicle is started, the [...]

OnStar ® OnStar ® uses several innovative technologies and live advisors to provide a wide range of safety , security , navigation, diagnostics, and calling services. Automatic Crash Response In a crash, built in sensors can automatically alert an OnStar advisor who is immediately connected to the vehicle to see if you need help. How OnStar Servi[...]

The OnStar system can record and transmit vehicle information. This information is automatically sent to an OnStar call center when Q is pressed, ] is pressed, or if the airbags or ACR system deploy . This information usually includes the vehicle's GPS location and, in the event of a crash, additional information regarding the crash that the v[...]

Section 2 Seats and Restraint System Front Seats ......................................... 2-2 Power Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Power Lumbar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 H e a t e d S e a t s ................................ ... 2 - 3 Heated and V enti[...]

Front Seats Power Seats The power seat controls are located on the outboard side of the seats. T o adjust the seat: . Move the seat forward or rearward by sliding the horizontal control forward or rearward. . Raise or lower the front part of the seat cushion by moving the front of the horizontal control up or down. . Raise or lower the rear part of[...]

Power Lumbar On vehicles with power lumbar , the control is located on the outboard sides of the front seat(s). T o increase or decrease support, press and hold the front or rear of the control. T o raise or lower the position of the lumbar support, press and hold the top or bottom of the control. V ehicles with a memory function allow seat setting[...]

Heated and V entilated Seats On vehicles with this feature, the buttons are located on the climate control panel. z (Heated Seat and Seatback): Press to heat the seat and seatback. { (V entilated Seat): Press to ventilate the seat. A light bar in the climate control display shows the setting; high, medium, or low . Press either button to start that[...]

{ W ARNING: Sitting in a reclined position when the vehicle is in motion can be dangerous. Even when buckled up, the safety belts cannot do their job when reclined like this. The shoulder belt cannot do its job because it will not be against your body . Instead, it will be in front of you. In a crash, you could go into it, receiving neck or other i[...]

Head Restraints Adjust the head restraint so that the top of the restraint is at the same height as the top of the occupant's head. This position reduces the chance of a neck injury in a crash. Pull the head restraint up to raise it. T o lower the head restraint, press the button, located on the top of the seatback, and push the head restraint[...]

Rear Seats Heated Seats If the vehicle has this feature, the controls are located on the center console. Pressing this button will turn the heated seat on at the highest setting. Each press of the button will decrease the seat temperature or turn the seat off. The light indicates which setting the seat is on, 3 being the highest. The engine must be[...]

Safety Belts Safety Belts: They Are for Everyone This section of the manual describes how to use safety belts properly . It also describes some things not to do with safety belts. { W ARNING: Do not let anyone ride where a safety belt cannot be worn properly . In a crash, if you or your passenger(s) are not wearing safety belts, the injuries can be[...]

In most states and in all Canadian provinces, the law requires wearing safety belts. Here is why: Y ou never know if you will be in a crash. If you do have a crash, you do not know if it will be a serious one. A few crashes are mild, and some crashes can be so serious that even buckled up, a person would not survive. But most crashes are in between[...]

Put someone on it. Get it up to speed. Then stop the vehicle. The rider does not stop. 2-10[...]

The person keeps going until stopped by something. In a real vehicle, it could be the windshield... or the instrument panel... 2-1 1[...]

or the safety belts! With safety belts, you slow down as the vehicle does. Y ou get more time to stop. Y ou stop over more distance, and your strongest bones take the forces. That is why safety belts make such good sense. Questions and Answers About Safety Belts Q: Will I be trapped in the vehicle after a crash if I am wearing a safety belt? A: Y o[...]

Q: If I am a good driver , and I never drive far from home, why should I wear safety belts? A: Y ou may be an excellent driver, but if you are in a crash — even one that is not your fault — you and your passenger(s) can be hurt. Being a good driver does not protect you from things beyond your control, such as bad drivers. Most accidents occur w[...]

Sit up straight and always keep your feet on the floor in front of you. The lap part of the belt should be worn low and snug on the hips, just touching the thighs. In a crash, this applies force to the strong pelvic bones and you would be less likely to slide under the lap belt. If you slid under it, the belt would apply force on your abdomen. This[...]

Q: What is wrong with this? A: The shoulder belt is too loose. It will not give as much protection this way . { W ARNING: Y ou can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury . The shoulder belt should fit snugly against your body . 2-15[...]

Q: What is wrong with this? A: The lap belt is too loose. It will not give nearly as much protection this way . { W ARNING: Y ou can be seriously hurt if your lap belt is too loose. In a crash, you could slide under the lap belt and apply force on your abdomen. This could cause serious or even fatal injuries. The lap belt should be worn low and snu[...]

Q: What is wrong with this? A: The belt is buckled in the wrong buckle. { W ARNING: Y ou can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not on the pelvic bones. This could cause serious internal injuries. Always buckle your belt into [...]

Q: What is wrong with this? A: The belt is over an armrest. { W ARNING: Y ou can be seriously injured if your belt goes over an armrest like this. The belt would be much too high. In a crash, you can slide under the belt. The belt force would then be applied on the abdomen, not on the pelvic bones, and that could cause serious or fatal injuries. Be[...]

Q: What is wrong with this? A: The shoulder belt is worn under the arm. It should be worn over the shoulder at all times. { W ARNING: Y ou can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury . Also, the belt would apply too m[...]

Q: What is wrong with this? A: The belt is behind the body . { W ARNING: Y ou can be seriously injured by not wearing the lap-shoulder belt properly . In a crash, you would not be restrained by the shoulder belt. Y our body could move too far forward increasing the chance of head and neck injury . Y ou might also slide under the lap belt. The belt [...]

Q: What is wrong with this? A: The belt is twisted across the body . { W ARNING: Y ou can be seriously injured by a twisted belt. In a crash, you would not have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly , or ask your dealer/retailer to fix it. 2-21[...]

Lap-Shoulder Belt All seating positions in your vehicle have a lap-shoulder belt. Here is how to wear a lap-shoulder belt properly . 1. Adjust the seat, if the seat is adjustable, so you can sit up straight. T o see how , see “ Seats ” in the Index. 2. Pick up the latch plate and pull the belt across you. Do not let it get twisted. The lap-shou[...]

5. T o make the lap part tight, pull up on the shoulder belt. It may be necessary to pull stitching on the safety belt through the latch plate to fully tighten the lap belt on smaller occupants. 6. This safety belt has a feature that will reduce the tension of the safety belt on the occupant's shoulder if the vehicle is on. T o set this featur[...]

Shoulder Belt Height Adjuster Y our vehicle has a shoulder belt height adjuster for the driver and right front passenger position. Adjust the height so that the shoulder portion of the belt is centered on your shoulder . The belt should be away from your face and neck, but not falling off your shoulder . Improper shoulder belt height adjustment cou[...]

Here is how to install a comfort guide to the safety belt: 1. Pull the elastic cord out from between the edge of the seatback and the interior body to remove the guide from its storage clip. 2. Place the guide over the belt and insert the two edges of the belt into the slots of the guide. 2-25[...]

3. Be sure that the belt is not twisted and it lies flat. The elastic cord must be under the belt and the guide on top. { W ARNING: A safety belt that is not properly worn may not provide the protection needed in a crash. The person wearing the belt could be seriously injured. The shoulder belt should go over the shoulder and across the chest. Thes[...]

4. Buckle, position, and release the safety belt as described previously in this section. Make sure that the shoulder belt crosses the shoulder . T o remove and store the comfort guide, squeeze the belt edges together so that you can take them out of the guide. Pull the guide upward to expose its storage clip, and then slide the guide onto the clip[...]

Safety Belt Extender If the vehicle's safety belt will fasten around you, you should use it. But if a safety belt is not long enough, your dealer/ retailer will order you an extender . When you go in to order it, take the heaviest coat you will wear , so the extender will be long enough for you. T o help avoid personal injury , do not let some[...]

The manufacturer's instructions that come with the booster seat state the weight and height limitations for that booster . Use a booster seat with a lap-shoulder belt until the child passes the below fit test: . Sit all the way back on the seat. Do the knees bend at the seat edge? If yes, continue. If no, return to the booster seat. . Buckle t[...]

{ W ARNING: Never do this. Never allow two children to wear the same safety belt. The safety belt can not properly spread the impact forces. In a crash, the two children can be crushed together and seriously injured. A safety belt must be used by only one person at a time. { W ARNING: Never do this. Never allow a child to wear the safety belt with [...]

Infants and Y oung Children Everyone in a vehicle needs protection! This includes infants and all other children. Neither the distance traveled nor the age and size of the traveler changes the need, for everyone, to use safety restraints. In fact, the law in every state in the United States and in every Canadian province says children up to some ag[...]

{ W ARNING: Never do this. Never hold an infant or a child while riding in a vehicle. Due to crash forces, an infant or a child will become so heavy it is not possible to hold it during a crash. For example, in a crash at only 40 km/h (25 mph), a 5.5 kg (12 lb) infant will suddenly become a 1 10 kg (240 lb) force on a person's arms. An infant [...]

{ W ARNING: Never do this. Children who are up against, or very close to, any airbag when it inflates can be seriously injured or killed. Never put a rear-facing child restraint in the right front seat. Secure a rear-facing child restraint in a rear seat. It is also better to secure a forward-facing child restraint in a rear seat. If you must secur[...]

Q: What are the different types of add-on child restraints? A: Add-on child restraints, which are purchased by the vehicle's owner , are available in four basic types. Selection of a particular restraint should take into consideration not only the child's weight, height, and age but also whether or not the restraint will be compatible wit[...]

{ W ARNING: A young child's hip bones are still so small that the vehicle's regular safety belt may not remain low on the hip bones, as it should. Instead, it may settle up around the child's abdomen. In a crash, the belt would apply force on a body area that is unprotected by any bony structure. This alone could cause serious or fat[...]

A forward-facing child seat (B) provides restraint for the child's body with the harness. A booster seat (C-D) is a child restraint designed to improve the fit of the vehicle's safety belt system. A booster seat can also help a child to see out the window . 2-36[...]

Securing an Add-On Child Restraint in the V ehicle { W ARNING: A child can be seriously injured or killed in a crash if the child restraint is not properly secured in the vehicle. Secure the child restraint properly in the vehicle using the vehicle's safety belt or LA TCH system, following the instructions that came with that child restraint a[...]

Where to Put the Restraint According to accident statistics, children and infants are safer when properly restrained in a child restraint system or infant restraint system secured in a rear seating position. We recommend that children and child restraints be secured in a rear seat, including: an infant or a child riding in a rear-facing child restr[...]

W ARNING: (Continued) always move the front passenger seat as far back as it will go. It is better to secure the child restraint in a rear seat. See Passenger Sensing System on page 2 ‑ 61 for additional information. When securing a child restraint in a rear seating position, study the instructions that came with the child restraint to make sure [...]

Lower Anchors Lower anchors (A) are metal bars built into the vehicle. There are two lower anchors for each LA TCH seating position that will accommodate a child restraint with lower attachments (B). T op T ether Anchor A top tether (A, C) anchors the top of the child restraint to the vehicle. A top tether anchor is built into the vehicle. The top [...]

Some child restraints that have a top tether are designed for use with or without the top tether being attached. Others require the top tether always to be attached. In Canada, the law requires that forward-facing child restraints have a top tether , and that the tether be attached. Be sure to read and follow the instructions for your child restrai[...]

The top tether anchors are located under covers on the rear seatback filler panel. Be sure to use an anchor located on the same side of the vehicle as the seating position where the child restraint will be placed. Do not secure a child restraint in a position without a top tether anchor if a national or local law requires that the top tether be att[...]

{ W ARNING: Do not attach more than one child restraint to a single anchor . Attaching more than one child restraint to a single anchor could cause the anchor or attachment to come loose or even break during a crash. A child or others could be injured. T o reduce the risk of serious or fatal injuries during a crash, attach only one child restraint [...]

2. If the child restraint manufacturer recommends that the top tether be attached, attach and tighten the top tether to the top tether anchor , if equipped. Refer to the child restraint instructions and the following steps: 2. 1. Find the top tether anchor . 2. 2. Open the top tether anchor cover to expose the anchor . 2. 3. If you have an adjustab[...]

If the position you are using has an adjustable headrest or head restraint and you are using a single tether , route the tether under the headrest or head restraint and in between the headrest or head restraint posts. 3. Push and pull the child restraint in different directions to be sure it is secure. Securing a Child Restraint in a Rear Seat Posi[...]

If the child restraint does not have the LA TCH system, you will be using the safety belt to secure the child restraint in this position. Be sure to follow the instructions that came with the child restraint. Secure the child in the child restraint when and as the instructions say . If more than one child restraint needs to be installed in the rear[...]

4. Pull the rest of the shoulder belt all the way out of the retractor to set the lock. 5. T o tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor . When installing a forward-facing child restraint, it may be helpful to us[...]

6. If the child restraint has a top tether , follow the child restraint manufacturer's instructions regarding the use of the top tether . See Lower Anchors and T ethers for Children (LA TCH) on page 2 ‑ 39 for more information. 7. Push and pull the child restraint in different directions to be sure it is secure. T o remove the child restrain[...]

W ARNING: (Continued) Secure rear-facing child restraints in a rear seat, even if the airbag is off. If you secure a forward-facing child restraint in the right front seat, always move the front passenger seat as far back as it will go. It is better to secure the child restraint in a rear seat. See Passenger Sensing System on page 2 ‑ 61 for addi[...]

4. Push the latch plate into the buckle until it clicks. Position the release button on the buckle so that the safety belt could be quickly unbuckled if necessary . 5. Pull the rest of the shoulder belt all the way out of the retractor to set the lock. 2-50[...]

6. T o tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor . When installing a forward-facing child restraint, it may be helpful to use your knee to push down on the child restraint as you tighten the belt. 7. Push and pul[...]

Airbag System The vehicle has the following airbags: . A frontal airbag for the driver . . A frontal airbag for the right front passenger . . A seat-mounted side impact airbag for the driver . . A seat-mounted side impact airbag for the right front passenger . . A roof-rail airbag for the driver and the passenger seated directly behind the driver .[...]

Here are the most important things to know about the airbag system: { W ARNING: Y ou can be severely injured or killed in a crash if you are not wearing your safety belt — even if you have airbags. Airbags are designed to work with safety belts, but do not replace them. Also, airbags are not designed to deploy in every crash. In some crashes safe[...]

{ W ARNING: Children who are up against, or very close to, any airbag when it inflates can be seriously injured or killed. Airbags plus lap-shoulder belts offer protection for adults and older children, but not for young children and infants. Neither the vehicle's safety belt system nor its airbag system is designed for them. Y oung children a[...]

Where Are the Airbags? The driver's frontal airbag is in the middle of the steering wheel. The right front passenger's frontal airbag is in the instrument panel on the passenger's side. 2-55[...]

Driver Side shown, Passenger Side similar The seat-mounted side impact airbags for the driver and right front passenger are in the side of the seatbacks closest to the door . Driver Side shown, Passenger Side similar The roof-rail airbags for the driver , right front passenger , and second row outboard passengers are in the ceiling above the side w[...]

{ W ARNING: If something is between an occupant and an airbag, the airbag might not inflate properly or it might force the object into that person causing severe injury or even death. The path of an inflating airbag must be kept clear . Do not put anything between an occupant and an airbag, and do not attach or put anything on the steering wheel hu[...]

Frontal airbags may inflate at different crash speeds. For example: . If the vehicle hits a stationary object, the airbags could inflate at a different crash speed than if the vehicle hits a moving object. . If the vehicle hits an object that deforms, the airbags could inflate at a dif ferent crash speed than if the vehicle hits an object that does[...]

What Makes an Airbag Inflate? In a deployment event, the sensing system sends an electrical signal triggering a release of gas from the inflator . Gas from the inflator fills the airbag causing the bag to break out of the cover and deploy . The inflator , the airbag, and related hardware are all part of the airbag module. Frontal airbag modules are[...]

The parts of the airbag that come into contact with you may be warm, but not too hot to touch. There may be some smoke and dust coming from the vents in the deflated airbags. Airbag inflation does not prevent the driver from seeing out of the windshield or being able to steer the vehicle, nor does it prevent people from leaving the vehicle. { W ARN[...]

In many crashes severe enough to inflate the airbag, windshields are broken by vehicle deformation. Additional windshield breakage may also occur from the right front passenger airbag. . Airbags are designed to inflate only once. After an airbag inflates, you will need some new parts for the airbag system. If you do not get them, the airbag system [...]

The passenger sensing system will turn off the right front passenger frontal airbag under certain conditions. The driver airbag, seat ‐ mounted side impact airbags and the roof ‐ rail airbags are not part of the passenger sensing system. The passenger sensing system works with sensors that are part of the right front passenger seat. The sensors[...]

The passenger sensing system is designed to turn off the right front passenger frontal airbag if: . The right front passenger seat is unoccupied. . The system determines that an infant is present in a rear-facing infant seat. . The system determines that a small child is present in a child restraint. . The system determines that a small child is pr[...]

The passenger sensing system is designed to enable (may inflate) the right front passenger's frontal airbag anytime the system senses that a person of adult size is sitting properly in the right front passenger's seat. When the passenger sensing system has allowed the airbag to be enabled, the on indicator will light and stay lit to remin[...]

{ W ARNING: If the airbag readiness light in the instrument panel cluster ever comes on and stays on, it means that something may be wrong with the airbag system. If this ever happens, have the vehicle serviced promptly , because an adult-size person sitting in the right front passenger's seat may not have the protection of the airbag(s). See [...]

Servicing Y our Airbag-Equipped V ehicle Airbags affect how the vehicle should be serviced. There are parts of the airbag system in several places around the vehicle. Y our dealer/retailer and the service manual have information about servicing the vehicle and the airbag system. T o purchase a service manual, see Service Publications Ordering Infor[...]

In addition, your vehicle has a passenger sensing system for the right front passenger's position, which includes sensors that are part of the passenger's seat. The passenger sensing system may not operate properly if the original seat trim is replaced with non-GM covers, upholstery or trim, or with GM covers, upholstery or trim designed [...]

Restraint System Check Checking the Restraint Systems Safety Belts Now and then, check that the safety belt reminder light, safety belts, buckles, latch plates, retractors, and anchorages are all working properly . Look for any other loose or damaged safety belt system parts that might keep a safety belt system from doing its job. See your dealer/r[...]

Replacing Restraint System Parts After a Crash { W ARNING: A crash can damage the restraint systems in your vehicle. A damaged restraint system may not properly protect the person using it, resulting in serious injury or even death in a crash. T o help make sure your restraint systems are working properly after a crash, have them inspected and any [...]

2 NOTES 2-70[...]

Section 3 Features and Controls Keys ........................... ..................... 3-3 Keyless Access System . . . . . . . . . . . . . . . . . . . . . . . . . 3-4 Keyless Access System Operation . . . . . . . . . . . . . . 3-5 Remote Vehicle Start . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10 Doors and Locks .........................[...]

Section 3 Features and Controls Object Detection Systems .. ..................... 3-41 Ultrasonic Rear Parking Assist (URP A) . . . . . . . . 3-41 Side Blind Zone Alert (SBZA) . . . . . . . . . . . . . . . . . . 3-44 Lane Departure W arning (LDW) . . . . . . . . . . . . . . . 3-47 Universal Home Remote System .. ............ .. 3-49 Universal Home [...]

Keys { W ARNING: Leaving children in a vehicle with the keyless access transmitter is dangerous for many reasons, children or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move. The windows will function with the keyless access transmitter in the vehicle and they could [...]

This key , located inside the keyless access transmitter , can be used for all locks. Press the button (A) near the bottom of the keyless access transmitter to remove the key . Never pull the key without pressing the button. Y our vehicle has a Keyless Access System with pushbutton start. See Ignition Positions on page 3 ‑ 26 for information on s[...]

If there is a decrease in the RKE operating range, try this: . Check the distance. The transmitter may be too far from the vehicle. Stand closer during rainy or snowy weather . . Check the location. Other vehicles or objects may be blocking the signal. T ake a few steps to the left or right, hold the transmitter higher , and try again. . Check the [...]

Q (Lock): Press once to lock the doors. The light on the front doors comes on and the turn signals flash. If Q is pressed twice, the horn will also sound. See “ Lights Flash at Lock ” and “ Horn Chirps at Lock ” under V ehicle Personalization on page 3 ‑ 58 to change the feedback feature. K (Unlock): Press once to unlock the driver door .[...]

Programming T ransmitters to the V ehicle Only keyless access transmitters programmed to this vehicle will work. If a transmitter is lost or stolen, a replacement can be purchased and programmed through your dealer/retailer . The vehicle can be reprogrammed so that lost or stolen transmitters no longer work. Each vehicle can have up to four transmi[...]

8. Remove the transmitter from the transmitter pocket and press K twice on each newly programmed transmitter to complete the process. 9. T o program additional transmitters, repeat Step 6. Press Acc. on the ignition switch if programming is complete. Programming without a Recognized T ransmitter This procedure requires three ten minutes cycles to c[...]

7. The DIC reads WAIT 10 MINUTES and counts down to zero. 8. The DIC displays OFF/ACC TO LEARN again. 9. Press Acc. on the ignition switch. 10. Steps 7, 8 and 9 will be repeated two more times. 1 1. A beep sounds and the DIC reads READY FOR FOB 1. All previously known transmitter programming has been erased. 12. A beep sounds once programming in co[...]

Battery Replacement Notice: When replacing the battery , do not touch any of the circuitry on the transmitter. Static from your body could damage the transmitter . 1. Separate the transmitter with a flat, thin object inserted into the slot on the side of the transmitter . 2. Remove the old battery . Do not use a metal object. 3. Insert the new batt[...]

3. If it is the first remote start since the vehicle has been driven, repeat these steps, while the engine is still running, to extend the engine running time by 10 minutes. Remote start can be extended one time. If the vehicle is left running it will automatically shut off after 10 minutes unless a time extension has been done. T o manually shut o[...]

The remote start feature will not operate if any of the following occur: . The check engine light is displayed. See “ Check Engine Light ” under Malfunction Indicator Lamp on page 4 ‑ 62 . . The valet lockout switch is on. . The keyless access transmitter is in the vehicle. . The vehicle's hood is open. . The vehicle personalization feat[...]

W ARNING: (Continued) . Outsiders can easily enter through an unlocked door when you slow down or stop your vehicle. Locking your doors can help prevent this from happening. There are several ways to lock and unlock your vehicle. From the outside: . Pull the front door handle. If you have the keyless access transmitter , the vehicle recognizes the [...]

Programmable Automatic Door Locks The vehicle was programmed so when the doors are closed, the ignition is on, and the shift lever is moved out of P (Park), all the doors will lock. The front doors can still be opened from the inside while the doors are locked. If a rear passenger needs to exit the vehicle, have that person use the manual knob or u[...]

Lockout Protection The vehicle can be programmed to sound the horn three times and unlock the driver's door when all doors are closed and there is a keyless access transmitter inside the interior of the vehicle. When the driver's door is reopened, the key in reminder chime will sound continuously . The vehicle will remain locked only when[...]

T runk Lid Release There are three ways to open the trunk lid. . V (T runk Lid Release): Press this button located on the driver's door . The vehicle must be in P (Park) or N (Neutral) and the valet mode turned off. T o disable valet mode, see Valet Lockout Switch on page 3 ‑ 24 . . Press the trunk lid release button on the keyless access tr[...]

If your vehicle has lost battery power , you can still access the trunk by unlocking and lowering the rear seat pass ‐ through door and pulling the emergency trunk release handle. Rear Seat Pass-Through Door T o open the door: 1. Pull the rear seat armrest down. 2. If the door is locked, insert the key into the lock and turn it counterclockwise. [...]

Windows { W ARNING: Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke. Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather. 3-18[...]

Power Windows { W ARNING: Leaving children in a vehicle with the keys is dangerous for many reasons, children or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move. The windows will function and they could be seriously injured or killed if caught in the path of a closin[...]

Express-Down/Up Window Any window can be lowered or raised all the way without holding the switch. Press the front of the window switch to the second position and release to activate the express-down feature. T o stop the window , briefly pull up the switch. Lift the front of the switch briefly to activate the express ‐ up feature. T o stop the w[...]

Express Window Anti ‐ Pinch Override { W ARNING: If express override is activated, the window will not reverse automatically . Y ou or others could be injured and the window could be damaged. Before you use express override, make sure that all people and obstructions are clear of the window path. In an emergency , the anti ‐ pinch feature can b[...]

Theft-Deterrent Systems V ehicle theft is big business, especially in some cities. This vehicle has theft-deterrent features, however, they do not make it impossible to steal. Theft-Deterrent System Y our vehicle has a theft-deterrent alarm system. The security light is located on the instrument panel cluster . If the ignition is off and a door is [...]

If a door , hood, or the trunk is opened without the keyless access transmitter , the horn will sound for 30 seconds and the lamps will flash for two minutes. The vehicle cannot be started without a keyless access transmitter . The Theft-Deterrent system will not arm if : . The key is used to turn the key cylinder to the lock position. . The driver[...]

V alet Lockout Switch The valet lockout switch is located inside the glove box. 9 (Off) : Press to turn the lockout feature off and allow the trunk to be opened with either the keyless access transmitter or the trunk release button located on the driver's door . R (On) : Press to turn the lockout feature on. The trunk cannot be unlocked or ope[...]

If the vehicle does not start and the keyless access transmitter appears to be undamaged, try another keyless access transmitter . Or , place the transmitter in the transmitter pocket. See “ NO FOBS DETECTED ” under DIC Warnings and Messages on page 4 ‑ 76 for additional information. Check the fuse. See Fuses and Circuit Breakers on page 6 ?[...]

Ignition Positions The vehicle has an electronic keyless ignition with pushbutton start. T o shift out of P (Park), the vehicle must be running or in ACCESSORY mode and the regular brake pedal must be applied. / (ST ART) : Press to start the engine with your foot on the brake pedal. The shifter must be in P (Park) or N (Neutral) and the keyless acc[...]

Starting the Engine T o place the transmission in the proper gear: Move the shift lever to P (Park) or N (Neutral). T o restart the engine when the vehicle is already moving, use N (Neutral). Notice: Do not try to shift to P (Park) if the vehicle is moving. If you do, you could damage the transmission. Shift to P (Park) only when the vehicle is sto[...]

Notice: Cranking the engine for long periods of time, by pressing the ST ART button immediately after cranking has ended, can overheat and damage the cranking motor , and drain the battery . Wait at least 15 seconds between each try , to allow the cranking motor to cool down. When the engine starts, let go of the accelerator . If the vehicle starts[...]

Engine Coolant Heater The engine coolant heater can provide easier starting and better fuel economy during engine warm ‐ up in cold weather conditions at or below − 18°C (0°F). Vehicles with an engine coolant heater should be plugged in at least four hours before starting. Some models have an internal thermostat in the cord which will prevent[...]

Automatic T ransmission Operation There are several different positions for the shift lever . P (Park) : This position locks the rear wheels. It is the best position to use when you start the engine because the vehicle cannot move easily . { W ARNING: It is dangerous to get out of the vehicle if the shift lever is not fully in P (Park) with the par[...]

Notice: Shifting to R (Reverse) while the vehicle is moving forward could damage the transmission. The repairs would not be covered by the vehicle warranty . Shift to R (Reverse) only after the vehicle is stopped. R (Reverse) : Use this gear to back up. At low vehicle speeds, you can also use R (Reverse) to rock your vehicle back and forth to get o[...]

Driver Shift Control (DSC) Notice: If you drive the vehicle at high RPMs without upshifting while using Driver Shift Control (DSC), you could damage the vehicle. Always upshift when necessary while using DSC. Driver Shift Control (DSC) allows you shift an automatic transmission similar to a manual transmission. T o use the DSC feature: 1. Move the [...]

If shifting is prevented for any reason, the selected gear will flash multiple times, indicating that the transmission has not shifted gears. The transmission will allow you to shift to the gear selected and will automatically downshift when the vehicle comes to a stop. This will allow for more power during take-off and passing. Parking Brake The p[...]

Shifting Into Park { W ARNING: It can be dangerous to get out of the vehicle if the shift lever is not fully in P (Park) with the parking brake firmly set. The vehicle can roll. If you have left the engine running, the vehicle can move suddenly . Y ou or others could be injured. T o be sure the vehicle will not move, even when you are on fairly lev[...]

T orque Lock T orque lock is when the weight of the vehicle puts too much force on the parking pawl in the transmission. This happens when parking on a hill and shifting the transmission into P (Park) is not done properly and then it is difficult to shift out of P (Park). T o prevent torque lock, set the parking brake and then shift into P (Park). [...]

Engine Exhaust { W ARNING: Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled. Exposure to CO can cause unconsciousness and even death. Exhaust may enter the vehicle if: . The vehicle idles in areas with poor ventilation (parking garages, tunnels, deep snow that may block underbody airflow or tail pipes). . The exhaust sme[...]

W ARNING: (Continued) smelled. It can cause unconsciousness and even death. Never run the engine in an enclosed area that has no fresh air ventilation. For more information, see Engine Exhaust on page 3 ‑ 36 . { W ARNING: It can be dangerous to get out of the vehicle if the automatic transmission shift lever is not fully in P (Park) with the park[...]

Compass Compass Operation Press O to turn the compass on or off. When the ignition and the compass feature are on, the mirror displays the compass heading after a few seconds. Compass Calibration If after few seconds, the display does not show a compass heading (for example, N for North), there may be a strong magnetic field interfering with the co[...]

3. Once the zone number displays, press O repeatedly until the correct zone number displays. Stop pressing the button and the mirror returns to normal operation. If C appears in the compass window , the compass may need calibration. See “ Compass Calibration ” listed previously . Outside Power Mirrors Controls for the outside power mirrors are [...]

Park Tilt Mirrors This feature assists the driver by improving rear obstacle detection and is useful in viewing the curb when parallel parking. The passenger and/or driver mirror tilts to a preselected position when the vehicle is in R (Reverse). This feature lets the driver view the curb when parallel parking. If further adjustment is needed after[...]

Object Detection Systems Ultrasonic Rear Parking Assist (URP A) For vehicles with the URP A system, it operates at speeds less than 3 mph (5 km/h), and assists the driver with parking and avoiding objects while in R (Reverse). The sensors on the rear bumper are used to detect the distance to an object up to 5 feet (1.5 m) behind the vehicle and at [...]

How the System Works URP A comes on automatically when the shift lever is moved into R (Reverse). The rear display briefly illuminates to indicate the system is working. URP A operates only at speeds less than 3 mph (5 km/h). If the vehicle is above this speed, the red light on the rear display will flash. T o be detected, objects must be at least [...]

When the System Does Not Seem to Work Properly If the URP A system will not activate due to a temporary condition a red light will be shown on the rear URP A display when the shift lever is moved into R (Reverse). This occurs under the following conditions: . The ultrasonic sensors are not clean. Keep your rear bumper free of mud, dirt, snow , ice [...]

Side Blind Zone Alert (SBZA) The vehicle may have a Side Blind Zone Alert (SBZA) system. Read this entire section before using the system. { W ARNING: SBZA is only a lane changing aid and does not replace driver vision. SBZA does not detect: . V ehicles outside the side blind zones which may be rapidly approaching. . Pedestrians, bicyclists, or ani[...]

The SBZA detection zones do not change if the vehicle is towing a trailer . So be extra careful when changing lanes while towing a trailer . How the System Works Left Side Mirror Display Right Side Mirror Display When the vehicle is started, both outside mirror displays will briefly come on to indicate that the system is operating. When the vehicle[...]

SBZA does not operate when the left or right corners of the rear bumper are covered with mud, dirt, snow , ice, slush, or in heavy rainstorms. For cleaning instructions, see Washing Y our Vehicle on page 6 ‑ 1 1 1 . If the DIC still displays the SIDE BLIND ZONE SYSTEM UNA V AILABLE message after cleaning the bumper , see your dealer/retailer . Th[...]

Lane Departure W arning (LDW) If the vehicle has the LDW system. Read this entire section before using the system. { W ARNING: The Lane Departure Warning (LDW) system does not steer the vehicle and is only an aid to help you stay in your driving lane. The LDW system may not: . Provide you with enough time to avoid a lane change collision. . Be loud[...]

How the System Works LDW uses a camera located between the inside rearview mirror and the windshield to detect the lane markings. @ (Lane Departure W arning): T o turn LDW on or off, press the CONFIG hard key located on the navigation radio, then press @ . See “ Configure Menu ” in the index of the Navigation System manual. The symbol will be h[...]

LDW Error Message SERVICE LANE DEP ARTURE SYSTEM : This message may appear in the DIC to indicate that LDW is not working properly . If this message remains on after continued driving, the system needs service. T ake the vehicle to your dealer/retailer . See DIC Warnings and Messages on page 4 ‑ 76 for more information. LANE DEP ARTURE SYSTEM UNA[...]

Read the instructions completely before attempting to program the transmitter . Because of the steps involved, it may be helpful to have another person available to assist you in programming the transmitter . Be sure to keep the original remote control transmitter for use in other vehicles, as well as, for future programming. Only the original remo[...]

2. Locate in the garage, the garage door opener receiver (motor-head unit). Locate the “ Learn ” or “ Smart ” button. It can usually be found where the hanging antenna wire is attached to the motor-head unit and may be a colored button. Press this button. After pressing this button, complete the following steps in less than 30 seconds. 3. I[...]

Programming Universal Home Remote — Fixed Code For questions or help programming the Universal Home Remote System, call 1-866-572-2728 or go to learcar2u.com. Most garage door openers sold before 1996 are Fixed Code units. Programming a garage door opener involves time-sensitive actions, so read the entire procedure before starting. Otherwise, th[...]

The hand held transmitter can have between eight to 12 dip switches depending on the brand of transmitter . The garage door opener receiver (motor head unit) could also have a row of dip switches that can be used when programming the Universal Home Remote. If the total number of switches on the motor head and hand held transmitter are different, or[...]

Example of Eight Dip Switches with Three Positions The panel of switches might not appear exactly as they do in the examples above, but they should be similar . The switch positions on your hand-held transmitter could be labeled, as follows: . A switch in the up position could be labeled as “ Up, ” “ +, ” or “ On. ” . A switch in the do[...]

4. The indicator lights will blink slowly . Enter each switch setting from Step 2 into your vehicle's Universal Home Remote. Y ou will have two and one-half minutes to complete Step 4. Now press one button on the Universal Home Remote for each switch setting as follows: . If you wrote “ Left, ” press the left button in the vehicle. . If yo[...]

Using Universal Home Remote Press and hold the appropriate button for at least half of a second. The indicator light will come on while the signal is being transmitted. Reprogramming Universal Home Remote Buttons Any of the three buttons can be reprogrammed by repeating the instructions. Erasing Universal Home Remote Buttons The programmed buttons [...]

Sunroof If the vehicle has a power sunroof, the switches are located on the overhead console. T o open or close the sunroof, the ignition must be on or Retained Accessory Power (RAP) must be active. See Retained Accessory Power (RAP) on page 3 ‑ 26 . Express Open: The express open feature will operate from the closed or partially open position. T[...]

Close: T o close the power sunroof, operate the controls according to one of the following: . From the open position, press and hold the driver's side sunroof switch forward. The sunshade must be closed manually . . From the vent position, press and hold the passenger's side sunroof switch rearward. Anti-Pinch: If an object is in the path[...]

If your vehicle has the base audio system, the following information explains the vehicle personalization on your vehicle. If your vehicle has the Navigation system, see “ Personalization ” in the Index of the Navigation System manual for information on vehicle personalization. If your vehicle has the ability to program additional personalizati[...]

7. T urn the tune/select knob and scroll to PERSONAL SETTINGS MENU, then press the tune/select knob to turn the feature on. A check mark appears after this selection when it is turned on and the entire list of personalization features will appear . 8. T urn the tune/select knob and scroll to the feature you want to change, then press the tune/selec[...]

3. Press the tune/select knob to turn on the DRIVER GREETING feature. Y ou will see a cursor on the screen. 4. T urn the tune/select knob until you reach the first letter you want; the letter will be highlighted. There is a complete alphabet with both upper and lower case letters and the numbers zero through nine. Also included are spaces and other[...]

KEY FOB REMINDER This feature sounds the horn three times when the driver's door is closed and there is a keyless access transmitter left inside of the vehicle. This will only occur when the vehicle is off. Programmable Modes Mode 1 : ON (default) Mode 2 : OFF T o program the vehicle to a different mode: 1. Enter the PERSONAL SETTINGS MENU by [...]

CLIMA TE CONTROL : The climate control system will engage when the vehicle is started using the remote start feature. It will be at the same climate control setting that was last used by the driver using that keyless entry transmitter . REAR WINDOW DEFOG : If this feature is active, the rear defogger will engage when the vehicle is started using th[...]

ST ART BUTTON RECALL If your vehicle has the optional memory package, you will have this feature. When this feature is turned on, you can recall any previously programmed seat, mirror , and steering column position when the start button on the ignition is pressed. Programmable Modes Mode 1 : ON Mode 2 : OFF (default) T o program the vehicle to a di[...]

AUTO EXIT COLUMN If your vehicle has the optional memory package, you will have this feature. When this feature is turned on, you can recall any previously programmed exit position for the steering column when the vehicle is off, the shift lever is in P (Park), and the driver's door is opened. Programmable Modes Mode 1 : ON Mode 2 : OFF (defau[...]

3. Press the tune/select knob to switch back and forth between on and off. When the mode is turned on, a check mark will appear next to the feature name. The mode you selected is now set. Y ou can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle. LIGHTS FLASH [...]

EXT . (Exterior) LIGHTS A T UNLOCK This feature turns on the exterior lamps when the keyless access transmitter is used to unlock the vehicle. The lamps will remain on for about 20 seconds unless a door is opened, the ignition is in ACCESSORY , on, or ST ART , or the keyless access transmitter is used to lock the vehicle. Programmable Modes Mode 1 [...]

TWILIGHT DELA Y This feature allows you to set the amount of time you want the exterior lamps to remain on after you exit the vehicle. Programmable Modes Mode 1 : 0:00 seconds (off) Mode 2 : 0:05 seconds (default) Mode 3 : 0:15 seconds Mode 4 : 0:30 seconds Mode 5 : 1:30 minutes Mode 6 : 2:00 minutes Mode 7 : 3:00 minutes Mode 8 : 4:00 minutes T o [...]

DRIVER UNLOCK A T OFF This feature allows the driver's door to automatically unlock when the ignition is turned off. Programmable Modes Mode 1 : ON Mode 2 : OFF (default) T o program the vehicle to a different mode: 1. Enter the PERSONAL SETTINGS MENU by following the instructions listed previously under “ Entering the Personal Settings Menu[...]

DRIVER UNLOCK IN P ARK The feature allows the driver's door to automatically unlock when the transmission is shifted into P (Park). Programmable Modes Mode 1 : ON Mode 2 : OFF (default) T o program the vehicle to a different mode: 1. Enter the PERSONAL SETTINGS MENU by following the instructions listed previously under “ Entering the Persona[...]

KEYLESS FT (Front) DOOR UNLOCK This feature automatically unlocks the appropriate front door when you approach the vehicle with the keyless access transmitter and pull the respective door handle. See Door Locks on page 3 ‑ 12 for more information. Programmable Modes Mode 1 : ON Mode 2 : OFF (default) T o program the vehicle to a different mode: 1[...]

LOCK DELA Y This feature delays the locking of the vehicle's doors for eight seconds after a power door lock switch or the lock button on the keyless access transmitter is pressed. The eight second delay occurs after the last door is closed. If the keyless access transmitter is left inside of the vehicle, the doors will not lock. Programmable [...]

Programmable Modes Mode 1 : ON Mode 2 : OFF (default) T o program the vehicle to a different mode: 1. Enter the PERSONAL SETTINGS MENU by following the instructions listed previously under “ Entering the Personal Settings Menu. ” 2. T urn the tune/select knob until KEYLESS LOCK DELA Y is highlighted. 3. Press the tune/select knob to switch back[...]

CHIME VOLUME HIGH This feature allows you to adjust the volume level of the vehicle's warning chimes. The chime volume cannot be turned off, only adjusted. Programmable Modes Mode 1 : NORMAL (default) Mode 2 : HIGH T o program the vehicle to a different mode: 1. Enter the PERSONAL SETTINGS MENU by following the instructions listed previously u[...]

The mode you selected is now set. Y ou can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle by pressing the F6 (BACK) button, located on the radio, to return to the PERSONAL SETTINGS MENU. Exiting the Personal Settings Menu Once you have finished making your s[...]

For vehicles with the base audio system, memory features are programmed and recalled through the radio from the DRIVER SELECTION and the DRIVER EXIT SETTINGS submenus. See “ Entering the Driver Selection Submenu ” and “ Entering the Driver Exit Settings Submenu ” later in this section for more information on recalling and programming the me[...]

Driver Selection Submenu Items DRIVER 1/DRIVER 2 The numbers on the back of each keyless access transmitter correspond to DRIVER 1 and DRIVER 2. If you would like to recall or store driver settings for the driver that does not correspond to the number on the back of the keyless access transmitter that you are using: 1. Enter the memory programming [...]

STORE DRIVER SETTINGS T o store driver settings: 1. Adjust your settings for the driver's seat, the outside rearview mirrors, and the steering column to a comfortable driving position. 2. Enter the memory programming mode for your driver settings by following the instructions listed previously under “ Entering the Driver Selection Submenu. ?[...]

Driver Exit Settings Submenu Items RECALL EXIT SETTINGS T o recall exit settings: 1. Enter the memory programming mode for your exit settings by following the instructions listed previously under “ Entering the Driver Exit Settings Submenu. ” 2. From the DRIVER EXIT SETTINGS submenu, turn the tune/select knob to scroll to RECALL EXIT SETTINGS a[...]

2 NOTES 3-80[...]

Section 4 Instrument Panel Instrument Panel Overview ................... ..... 4-3 Hazard W arning Flashers . . . . . . . . . . . . . . . . . . . . . . . 4-3 Horn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3 Power T ilt Wheel and T elescopic Steering Column . . . . . . . . . . . . . . . . . . . . . . .[...]

Section 4 Instrument Panel Engine Coolant T emperature Gage . . . . . . . . . . . . 4-61 T ire Pressure Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-62 Malfunction Indicator Lamp . . . . . . . . . . . . . . . . . . . . 4-62 Oil Pressure Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-66 Security Light . . . . . [...]

Instrument Panel Overview Hazard W arning Flashers | : Press this button located on the console, near the shift lever , to make the front and rear turn signal lamps flash on and off. This warns others that you are having trouble. Press again to turn the flashers off. When the hazard warning flashers are on, the turn signals do not work. Horn Press [...]

Heated Steering Wheel For vehicles with a heated steering wheel, the button for this feature is located on the steering wheel. ( : Press to turn the heated steering wheel on or off. A light on the button displays when the feature is turned on. The steering wheel takes about three minutes to start heating. T urn Signal/Multifunction Lever The lever [...]

The lever returns to its starting position when it is released. If after signaling a turn or lane change the arrow flashes rapidly or does not come on, a signal bulb may be burned out. Have the bulbs replaced. If the bulb is not burned out, check the fuse. See Fuses and Circuit Breakers on page 6 ‑ 1 17 . T urn Signal On Chime If the turn signal [...]

Forward Collision Alert (FCA) System If the vehicle has this system, read this entire section before using it. The system operates on a radio frequency subject to Federal Communications Commission (FCC) Rules and with Industry Canada. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This d[...]

The Forward Collision Alert (FCA) controls are located on the end of the multifunction lever . 9 (Off) : Turns the system off. R (On) : Turns the system on. The Head-Up Display must be on and properly adjusted. If the HUD is not on, FCA will not be enabled and you will not be provided with FCA audible and visual warnings. See Head-Up Display (HUD) [...]

W arning the Driver The alert symbol will flash on the HUD and a warning beep will sound when driver action may be required. The driver warning is active when: . Y ou are approaching a vehicle too quickly . . Y ou are following a vehicle ahead much too closely . See Defensive Driving on page 5 ‑ 2 for more information. Detecting the V ehicle Ahea[...]

Unnecessary W arnings FCA may occasionally provide an unnecessary warning to guard rails, signs, and other stationary objects. This is normal operation, your vehicle does not need service. Other Messages There are three messages that may appear on the Driver Information Center (DIC). They are CLEAN RADAR, RADAR CRUISE NOT READY and SERVICE RADAR CR[...]

Windshield Wipers The windshield wiper lever is on the right side of the steering column. Move the lever to select the wiper speed: 7 (Mist) : Single wipe, move to 7 and then release it. The lever will return to its original position. For several wipes, hold the lever in this position. 9 (Off) : Turns the windshield wipers off. & (Delay) : For [...]

Windshield W asher The windshield washer button is located at the end of the windshield wiper lever on the right side of the steering column. K (W asher Fluid) : Press and hold to spray windshield washer fluid on the windshield. The washer will spray until the button is released. The wipers will continue to clear the window for about six seconds af[...]

Cruise Control With cruise control, a speed of about 40 km/h (25 mph) or more can be maintained without keeping your foot on the accelerator . Cruise control does not work at speeds below about 40 km/h (25 mph). If the brakes are applied, the cruise control shuts off. { W ARNING: Cruise control can be dangerous where you cannot drive safely at a st[...]

T (Set/Decrease) : Press to set the speed or to decrease the speed when cruise is already active. [ (Cancel): Press this button on the steering wheel to cancel cruise control without erasing the set speed from memory . Setting Cruise Control { W ARNING: If you leave your cruise control on when you are not using cruise, you might hit a button and go[...]

Increasing Speed While Using Cruise Control There are two ways to go to a higher speed: . Use the accelerator pedal to get to the higher speed. Press T at the end of the lever , then release the button and the accelerator pedal. The vehicle will cruise at the higher speed. . Move the cruise switch from R to S . Hold it there until the desired speed[...]

When going downhill, you might have to brake to keep the vehicle's speed down. Applying the brake will turn off the cruise control. If you need to apply the brake due to the grade of the downhill slope, you might not want to attempt to use the cruise control feature. Ending Cruise Control There are three ways to end cruise control. . Step ligh[...]

The vehicle's braking during Adaptive Cruise Control is comparable to a person applying moderate pressure to the vehicle's brake pedal. T o disengage Adaptive Cruise Control, apply the brake. If no vehicle is in your path, your vehicle will react like traditional cruise control. { W ARNING: Adaptive Cruise Control will not apply hard brak[...]

W ARNING: (Continued) . On slippery roads, fast changes in tire traction can cause needless wheel spinning, and you could lose control. Do not use cruise control on slippery roads. . When weather limits visibility , such as when in fog, rain, or snow conditions, Adaptive Cruise Control performance is limited. There may not be enough distance to ada[...]

Engaging Adaptive Cruise Control With the Set Button { W ARNING: If you leave your Adaptive Cruise Control switch on when you are not using cruise, you might hit a button and go into cruise when you do not want to. Y ou could be startled and even lose control. Keep the Adaptive Cruise Control switch off until you want to use cruise control. { W ARN[...]

United States version shown, Canada similar This symbol appears on the Head-Up Display (HUD) to indicate that Adaptive Cruise Control is active. The number indicates the set speed. See Head-Up Display (HUD) on page 4 ‑ 38 for more information. Make sure the set speed is visible on the HUD so you know the speed your vehicle will accelerate to if a[...]

Decreasing Set Speed While Using Adaptive Cruise Control Press T at the end of the lever until the lower speed desired is reached, then release the button. T o slow down in small amounts, briefly press T . Each this is done, the set speed will be 1.6 km/h (1 mph) slower. Resuming a Set Speed If the brakes are applied while the Adaptive Cruise Contr[...]

The range of selectable distances may not be appropriate for all drivers and driving conditions. If you prefer to travel at a following distance farther than Adaptive Cruise Control allows, disengage the system and drive manually . United States version shown, Canada similar A graphic on the HUD indicates the selected following distance. This pictu[...]

Approaching and Following a V ehicle The vehicle ahead symbol only appears on the HUD when a vehicle ahead is detected in your path. If this symbol does not appear , or disappears briefly , Adaptive Cruise Control will not respond to vehicles you may see ahead. { W ARNING: When the Adaptive Cruise Control radar is blocked by snow , ice, or dirt, it[...]

Stationary or V ery Slow-Moving Objects { W ARNING: Adaptive Cruise Control may not detect and react to stationary or slow ‐ moving vehicles or other objects ahead of you. Y ou could crash into an object ahead of you. Do not use Adaptive Cruise Control when approaching stationary or slow ‐ moving vehicles or other objects. { W ARNING: Adaptive [...]

Passing a V ehicle/Adaptive Cruise Control Override T o increase speed to pass a vehicle, use the accelerator pedal. While you are doing this, the system will not automatically apply the brakes. A PEDAL APPLIED ACC OVERRIDE message will appear on the HUD. See Head-Up Display (HUD) on page 4 ‑ 38 for additional information. Once you pass the vehic[...]

When following a vehicle and entering a curve, Adaptive Cruise Control could lose track of the vehicle in your lane and your vehicle could accelerate. When this happens, the vehicle ahead symbol will not appear on the HUD. Adaptive Cruise Control might detect a vehicle that is not in your lane and apply the brakes. Adaptive Cruise Control might occ[...]

Highway Exit Ramps { W ARNING: Adaptive Cruise Control may lose track of the vehicle ahead and accelerate up to your set speed while entering or on highway exit ramps. Y ou could be startled by this acceleration and even lose control of the vehicle. Disengage Adaptive Cruise Control before entering a highway exit ramp. Do not use Adaptive Cruise Co[...]

Erasing Set Speed Memory The set speed memory is erased when the Adaptive Cruise Control switch or the ignition is turned off. Other Messages There are three messages that may appear on the DIC. They are SERVICE RADAR CRUISE, RADAR CRUISE NOT READY and CLEAN RADAR. These messages will appear to indicate a problem with the Adaptive Cruise Control. S[...]

AUTO (Automatic) : Turns the exterior lamps on and off automatically depending upon how much light is outside of the vehicle. The automatic lights may be disabled even if the control is in the AUTO position. T o enable automatic lighting do any of the following: . T urn the headlamp control from AUTO to off and release the switch. It returns back t[...]

has been turned on, it remains on each time the vehicle is started. Additionally , the IntelliBeam system must be enabled. T o enable the System, turn the exterior lamp control to AUTO, with the turn signal/multifunction lever in its starting position. The High-Beam On Light appears on the instrument panel cluster when the high-beams are on. See Hi[...]

IntelliBeam may not turn off the high-beams if the system cannot detect other vehicle's lamps because of any of the following: . The others vehicle's lamp(s) are missing, damaged, obstructed from view , or otherwise undetected. . The other vehicle's lamp(s) are covered with dirt, snow and/or road spray . . The other vehicle's la[...]

Cleaning the IntelliBeam Light Sensor The light sensor is located on the inside of the vehicle at the back of the rearview mirror . Clean the light sensor window , periodically , using glass cleaner on a soft cloth. Gently wipe the sensor window . Do not spray glass cleaner directly on the surface of the sensor window . Wiper Activated Headlamps Th[...]

Daytime Running Lamps (DRL) Daytime Running Lamps (DRL) can make it easier for others to see the front of your vehicle during the day . Fully functional daytime running lamps are required on all vehicles first sold in Canada. The DRL system comes on when the following conditions are met: . It is still daylight and the ignition is on. . The automati[...]

Light Sensor The light sensor for the DRL is located on top of the instrument panel. If the sensor is covered, it will prevent it from sensing light, and the exterior lamps may come on when they are not needed. Fog Lamps The fog lamp controls are located on the turn signal/ multifunction lever . # (Fog Lamps) : The band with this symbol is used to [...]

T wilight Sentinel ® T wilight Sentinel ® can turn the lamps on and off for you. A light sensor on top of the instrument panel makes the T wilight Sentinel work, so be sure it is not covered. With T wilight Sentinel the following will happen: . When it is dark enough outside, the front turn signal lamps (DRL) will go off, and the headlamps and pa[...]

T wilight Sentinel also provides exterior illumination as you leave the vehicle. If T wilight Sentinel has turned on the lamps when you turn off the ignition, the lamps will remain on until: . The exterior lamp switch is moved from off to the parking lamp position. . A delay time that you select has elapsed. See V ehicle Personalization on page 3 ?[...]

Entry Lighting The entry lighting system turns on the reading and dome lamps and the backlighting to the exterior lamp control when a door is opened or if you press the remote keyless entry transmitter unlock button. If activated by the transmitter , the lighting will remain active for about 25 seconds. The entry lighting system uses the light sens[...]

speed. For more battery saving information, see “ Battery Saver Active Message ” under DIC Warnings and Messages on page 4 ‑ 76 . Electric Power Management The vehicle has Electric Power Management (EPM) that estimates the battery's temperature and state of charge. It then adjusts the voltage for best performance and extended life of the[...]

Head-Up Display (HUD) { W ARNING: If the HUD image is too bright, or too high in your field of view , it may take you more time to see things you need to see when it is dark outside. Be sure to keep the HUD image dim and placed low in your field of view . For vehicles with the Head-Up Display (HUD), some of the driver information that appears on th[...]

The HUD controls are located to the left of the steering wheel on the DIC control panel. Off : Turn the brightness control knob fully counterclockwise to turn the HUD display off. ~ (Head-Up Display) : Press to move the HUD display up or down on the windshield. HUD cannot be adjusted side ‐ to ‐ side. Brightness Control : Press the knob on the [...]

The Ignition is On and the HUD Image Cannot Be Seen Check to see if: . The HUD unit is covered. . The brightness is adjusted properly . . The HUD display is adjusted to the proper height. . Ambient light in the direction the vehicle is facing is low . . A fuse is blown. See Fuses and Circuit Breakers on page 6 ‑ 1 17 . The windshield is part of t[...]

The Speed Advisor can be set to show a speed alert when the vehicle speed exceeds the speed alert limit as set in the DIC menu. Depending on the level of the HUD on the vehicle, your HUD may work like either of the following: . The HUD speedometer will turn red when the vehicle speed exceeds the speed alert limit. When the vehicle speed is at or be[...]

Accessory Power Outlet(s) Accessory power outlets can be used to plug in electrical equipment, such as a cellular telephone. The vehicle has one outlet in front of the center console, one in the center console lid and there may be an additional outlet in the rear of the center console. The vehicle may have a small cap that must be removed to access[...]

Ashtray(s) and Cigarette Lighter The vehicle may have an ashtray and cigarette lighter . Notice: If papers, pins, or other flammable items are put in the ashtray , hot cigarettes or other smoking materials could ignite them and possibly damage the vehicle. Never put flammable items in the ashtray . Ashtray For vehicles with an ashtray , it is locat[...]

Climate Controls Dual Climate Control System The heating, cooling, and ventilation can be controlled for the vehicle with this system. Automatic Operation V ehicles With Heated and V entilated Seats Shown, V ehicles Without Similar A. Driver and Passenger Side Power Buttons B. V entilated Seat C. AUTO D. Recirculation E. Air Conditioning F . Heated[...]

The display can be changed from English to metric units through the Driver Information Center (DIC). See DIC Operation and Displays on page 4 ‑ 70 . Manual Operation O (Driver's T emperature Control) : Press to turn the entire climate control system on or off. T urn the knob to increase or decrease the temperature inside the vehicle. O (Pass[...]

- (Defog) : This mode clears the windows of fog or moisture. Air is directed to the windshield and floor outlets, with some air directed to the side windows and outboard panel outlets. When this mode is selected, the system turns off recirculation and runs the air-conditioning compressor unless the outside temperature is at or below freezing. If re[...]

= (Rear Window Defogger) : Press to turn the rear window defogger on or off. The rear window defogger stays on for 10 minutes, before turning off. If the vehicle's speed is above 48 km/h (30 mph), the rear defogger stays on continuously . If turned on again, the defogger only runs for about five minutes before turning off. The defogger can als[...]

The climate control system uses the information from these sensors to adjust the temperature, the fan speed and the air delivery , in order to maintain the selected temperature. The system may also supply cooler air to the side of the vehicle facing the sun. Do not cover the sensors or the automatic climate control system will not work properly . O[...]

Rear Climate Control System The vehicle has a rear climate control system. The base model includes air outlets in the rear of the center console for cooling and under-seat air outlets for heating. The temperature, amount of airflow , and the air delivery mode is controlled automatically by the front climate control system. Some vehicles may have an[...]

Passenger Compartment Air Filter Y our vehicle may be equipped with a passenger compartment air filter . There are two types of filters available. There is a standard dust filter that traps small particles including pollen. There is, also, a dust/odor filter available that traps dust and pollen and uses a charcoal element to help reduce many offens[...]

4. Lift the inboard edge of the deflector to release the retention tab. 5. Lift and slide the water deflector toward the inboard side and remove it. 6. The top edge of the filter should be visible. Reach in and lift the filter out , pulling upward and toward the front of the vehicle. 7. Insert the new air filter by sliding it back into place. Make [...]

Instrument Panel Cluster The instrument panel cluster is designed to show how the vehicle is running. It shows how fast the vehicle is going, how much fuel is being used and many of the other things needed to drive safely and economically . United States Base version shown, Canada and Uplevel similar 4-52[...]

Speedometer and Odometer The speedometer shows the speed in both kilometers per hour (km/h) and miles per hour (mph). See DIC Operation and Displays on page 4 ‑ 70 for more information. The odometer mileage can be checked without the vehicle running. The vehicle's odometer works together with the driver information center . The odometer can [...]

Passenger Safety Belt Reminder Light Several seconds after the engine is started, a chime sounds for several seconds to remind the front passenger to buckle their safety belt. The passenger safety belt light, located on the instrument panel, comes on and stays on for several seconds and then flashes for several more. This chime and light are repeat[...]

{ W ARNING: If the airbag readiness light stays on after the vehicle is started or comes on while driving, it means the airbag system might not be working properly . The airbags in the vehicle might not inflate in a crash, or they could even inflate without a crash. T o help avoid injury , have the vehicle serviced right away . If there is a proble[...]

Then, after several more seconds, the status indicator will light either ON or OFF , or either the on or off symbol to let you know the status of the right front passenger's frontal airbag. If the word ON or the on symbol is lit on the passenger airbag status indicator , it means that the right front passenger's frontal airbag is enabled [...]

If, after several seconds, both status indicator lights remain on, or if there are no lights at all, there may be a problem with the lights or the passenger sensing system. See your dealer/retailer for service. { W ARNING: If the airbag readiness light in the instrument panel cluster ever comes on and stays on, it means that something may be wrong [...]

Brake System W arning Light The vehicle's hydraulic brake system is divided into two parts. If one part is not working, the other part can still work and stop the vehicle. For good braking both parts need to be working. If the warning light comes on, there is a brake problem. Have the brake system inspected right away . United States Canada Th[...]

Antilock Brake System (ABS) W arning Light For vehicles with the Antilock Brake System (ABS), this light comes on briefly when the engine is started. If it does not, have the vehicle serviced by your dealer/retailer . If the system is working normally the indicator light then goes off. If the ABS light stays on, turn the ignition off. If the light [...]

T raction Control System (TCS) W arning Light The TCS warning light comes on briefly when the engine is started. If it does not, have the vehicle serviced by your dealer/retailer . If the T raction Control System (TCS) warning light comes on and stays on, there may be a problem with the TCS. The light also comes on if the TCS is turned off using th[...]

Engine Coolant T emperature W arning Light The engine coolant temperature warning light comes on when the engine is very hot. This light also comes on briefly when the vehicle is started. If the light does not go out or comes on and stays on while driving, there may be a problem with the cooling system. Driving with engine coolant temperature light[...]

Tire Pressure Light For vehicles with a tire pressure monitoring system, this light comes on briefly when the engine is started. It provides information about tire pressures and the Tire Pressure Monitoring System. When the Light is On Steady This indicates that one or more of the tires is significantly underinflated. A tire pressure message in the[...]

This comes on briefly while starting the engine. If it does not come on, have the vehicle serviced by your dealer/retailer . If the check engine light comes on and stays on, while the engine is running, this indicates that there is an OBD II problem and service is required. Malfunctions often are indicated by the system before any problem is appare[...]

If the light continues to flash, when it is safe to do so, stop the vehicle. Find a safe place to park the vehicle. T urn off the ignition, wait at least 10 seconds, and restart the engine. If the light is still flashing, follow the previous steps and see your dealer/retailer for service as soon as possible. Light On Steady : An emission control sy[...]

Emissions Inspection and Maintenance Programs Some state/provincial and local governments have or might begin programs to inspect the emission control equipment on the vehicle. Failure to pass this inspection could prevent getting a vehicle registration. Here are some things to know to help the vehicle pass an inspection: . The vehicle will not pas[...]

Oil Pressure Light For vehicles with an oil pressure light, if there is a problem with the oil, the light may stay on after the engine is started, or comes on while driving. This light indicates that oil is not going through the engine quickly enough to keep it lubricated. The engine could be low on oil or could have some other oil problem. Have th[...]

Security Light For information regarding this light and the vehicle's security system, see Theft-Deterrent System on page 3 ‑ 22 . Fog Lamp Light The fog lamp light comes on when the fog lamps are in use. The light goes out when the fog lamps are turned off. See Fog Lamps on page 4 ‑ 33 for more information. Lights On Reminder This light c[...]

Highbeam On Light This light comes on when the high-beam headlamps are in use. See Headlamp High/Low-Beam Changer on page 4 ‑ 5 for more information. Fuel Gage The fuel gage shows approximately how much fuel is in the fuel tank. It works only when the engine is on. An arrow on the fuel gage indicates the side of the vehicle the fuel door is on. I[...]

Driver Information Center (DIC) The Driver Information Center (DIC) gives you the status of many of your vehicle's systems. The DIC is also used to display warning/status messages. All messages will appear in the DIC display located at the bottom of the instrument panel cluster , below the tachometer and speedometer . The DIC buttons are locat[...]

DIC Operation and Displays The Driver Information Center (DIC) has different modes which can be accessed by pressing the four DIC buttons located on the instrument panel, to the left of the steering wheel. DIC Buttons (Base Level) If your vehicle does not have a Head-Up Display (HUD), these are the buttons for the DIC. « 4 ª (Information): Press [...]

DIC Buttons (Uplevel) If the vehicle has a HUD, these are the buttons for the DIC. « 4 ª (Information): Press the top or bottom of this button to scroll through the available vehicle information displays which include digital speed display , if your vehicle has this feature, fuel range, fuel economy , fuel used, average speed, timer , battery vol[...]

Information Display Menu Items The following display menu items can be displayed by pressing the information button. MPH (km/h) If the vehicle has this display , it shows the vehicle's speed digitally in either miles per hour (mph) or kilometers per hour (km/h). MILES RANGE (km RANGE) This display shows the approximate number of remaining mile[...]

A VG MPH (A VG km/h) This display shows the average speed of the vehicle in miles per hour (mph) or kilometers per hour (km/h). This average is calculated based on the various vehicle speeds recorded since the last reset of this display . T o reset A VG MPH, press the reset button. The display will return to zero. HUD Speed Advisor ON/OFF (On V ehi[...]

BA TTER Y VOL TS This display shows the current battery voltage. If the voltage is in the normal range, the value will display . For example, the display may read 13.2 BA TTERY VOL TS. If the voltage is low , the display will have LOW after it. If the voltage is high, the display will have HIGH after it. Y our vehicle's charging system regulat[...]

ENGLISH DISPLA Y UNITS (METRIC DISPLA Y UNITS) This display allows you to select between English and metric units of measurement if your vehicle has the uplevel DIC. Press the reset button to switch between English and metric units. Blank Line This display shows no information. T rip Information Display Menu Items The following display menu items c[...]

DIC W arnings and Messages Messages are displayed on the DIC to notify the driver that the status of the vehicle has changed and that some action may be needed by the driver to correct the condition. Multiple messages may appear one after another . The text messages are the same for both the base audio and Navigation systems unless otherwise indica[...]

BA TTER Y NOT CHARGING SERVICE CHARGING SYS (System) This symbol appears with this message. This message displays when a problem with the charging system has been detected. Have your vehicle serviced by your dealer/retailer . BA TTER Y SA VER ACTIVE This message displays when the system detects that the battery voltage is dropping beyond a reasonab[...]

BA TTER Y VOL T AGE LOW This symbol appears with this message. This message displays when the electrical system is charging less than 10 volts or the battery has been drained. If this message appears immediately after starting the engine, it is possible that the generator can still recharge the battery . The battery should recharge while driving, b[...]

CHECK TIRE PRESSURE This message displays when the pressure in one or more of the vehicle's tires needs to be checked. If a tire pressure message appears on the DIC, stop as soon as you can. Have the tire pressures checked and set to those shown on the Tire Loading Information label. See Tires on page 6 ‑ 52 , Loading the Vehicle on page 5 ?[...]

ENGINE COOLANT HOT IDLE ENGINE Notice: If you drive your vehicle while the engine is overheating, severe engine damage may occur . If an overheat warning appears on the instrument panel cluster and/or DIC, stop the vehicle as soon as possible. Do not increase the engine speed above normal idling speed. See Engine Overheating on page 6 ‑ 32 for mo[...]

destination. The performance may be reduced the next time the vehicle is driven. The vehicle may be driven at a reduced speed while this message is on, but acceleration and speed may be reduced. Anytime this message stays on, take the vehicle to your dealer/ retailer for service as soon as possible. ENGINE PROTECTION REDUCED RPM'S (Revolutions[...]

HOOD AJAR This symbol appears with this message. This message displays when the hood is not closed completely . Make sure that the hood is closed completely . See Hood Release on page 6 ‑ 12 . ICE POSSIBLE This message displays when the outside temperature is cold enough to create icy road conditions. Adjust your driving accordingly . KEY FOB BA [...]

NO FOBS DETECTED This message displays if the vehicle does not detect the presence of a keyless access transmitter when you have attempted to start the vehicle or a vehicle door has just closed. The following conditions may cause this message to appear: . Driver-added equipment plugged into the accessory power outlet on the center console is causin[...]

NO FOB OFF OR RUN? This message displays when the keyless access transmitter is not detected inside the vehicle while you are trying to turn the ignition off. Y our vehicle may be near a strong radio antenna signal causing the keyless access system to be jammed. The vehicle remains in ACCESSORY until OFF or ST ART has been pressed or 10 minutes has[...]

PRESS ST ART AND BRAKE TO ST ART ENGINE This message displays when you need to press down on the brake pedal while pressing the start button on the electronic keyless ignition when trying to start your vehicle. See Starting the Engine on page 3 ‑ 27 for more information. RADAR CRUISE NOT READY This message displays when the Adaptive Cruise Contro[...]

SERVICE AIR BAG This message displays if there is a problem with the airbag system. Have your vehicle serviced by your dealer/retailer immediately . See Airbag Readiness Light on page 4 ‑ 54 for more information. SERVICE BRAKE ASSIST This message displays when a problem with the panic brake assist system has been detected. Have your vehicle servi[...]

system inspected by your dealer/retailer as soon as possible. See StabiliT rak ® System on page 5 ‑ 6 or Enhanced StabiliT rak ® on page 5 ‑ 7 for more information. For vehicles with the Active Steering with Enhanced StabiliT rak option, in some cases when the SERVICE ST ABILITY SYS message is displayed, a larger degree of steering wheel inpu[...]

SERVICE SUSPENSION SYS (System) This message displays when the suspension system is not operating properly . Have your vehicle serviced by your dealer/retailer . If your All-Wheel Drive (AWD) vehicle has the Active Steering with Enhanced StabiliTrak option and the suspension system needs service, the Enhanced StabiliT rak system may be operating in[...]

SIDE BLIND ZONE ALERT SYSTEM OFF If your vehicle has the Side Blind Zone Alert (SBZA) system, this message displays when the SBZA system has been turned off. See Side Blind Zone Alert (SBZA) on page 3 ‑ 44 and DIC Operation and Displays on page 4 ‑ 70 for more information. SIDE BLIND ZONE SYSTEM UNA V AILABLE If your vehicle has the Side Blind [...]

ST ABILITY SECURE MODE If your All-Wheel Drive (AWD) vehicle has the Active Steering with Enhanced StabiliTrak option, this message displays when the stability control system is in the secure mode. Stability Secure Mode is set automatically when certain system faults or vehicle conditions are detected. When the Stability Secure Mode is activated, t[...]

with directional control of the vehicle. Adjust your driving accordingly . See StabiliT rak ® System on page 5 ‑ 6 or Enhanced StabiliT rak ® on page 5 ‑ 7 for more information. ST ABILITY SYS (System) READY This message displays any time StabiliTrak is turned back on using the TC (traction control) on/off button. See T raction Control System[...]

TRACTION ACTIVE This message displays when the T raction Control System (TCS) is actively limiting wheel spin. Slippery road conditions may exist if this message is displayed, so adjust your driving accordingly . The message stays on for a few seconds after the TCS stops limiting wheel spin. See T raction Control System (TCS) on page 5 ‑ 9 for mo[...]

Other Messages Here are more messages that you can receive on your Driver Information Center (DIC). T o acknowledge a message and read another message that may have come on at the same time, press the reset button. . ACCESSORY ACTIVE See Ignition Positions on page 3 ‑ 26 . . KNOWN FOB See “ Matching Transmitter(s) to Y our V ehicle ” under Ke[...]

Audio System(s) Determine which radio the vehicle has and read the following pages to become familiar with its features. { W ARNING: T aking your eyes off the road for extended periods could cause a crash resulting in injury or death to you or others. Do not give extended attention to entertainment tasks while driving. This system provides access t[...]

Setting the Clock T o adjust the time: 1. Press w ,located on the radio, to enter the main menu. 2. T urn w until SET CLOCK displays. 3. Press w to select SET CLOCK. 4. T urn w to adjust the time. 5. Press w to update the time and VEHICLE TIME UPDA TED displays. T o adjust the date: 1. Press w to enter the main menu. 2. T urn w until SET DA TE disp[...]

Radio Data System (RDS) The audio system has RDS features that are available for use only on FM stations that broadcast RDS information. With RDS: . Stations can be selected based on programming . Stations with traffic announcements can be selected . Announcements concerning local and national emergencies can be received. . Messages display from ra[...]

T o scan preset stations: 1. Press and hold © or ¨ for more than two seconds until a beep sounds and PSCAN displays. The radio goes to the first preset station, plays for five seconds, then goes to the next preset station. 2. Press and release © or ¨ to stop scanning. A LOCAL/DIST ANT Selection: The radio can be set to search for local stations[...]

Setting Preset Stations Up to 30 stations (six FM1, six FM2, six AM, six XM1 and six XM2), can be programmed on the six numbered pushbuttons. T o program preset stations: 1. T une to a station and select the equalization, DSP , or PTY (program type) setting if desired. 2. Press and hold one of the six numbered pushbuttons for two seconds until a be[...]

Adjusting the T one (Bass/Midrange/T reble) T o adjust the bass, midrange, and treble: 1. Press w to enter the main menu. 2. T urn w until BASS-MID-TREBLE displays. 3. Press w to enter the tone settings. 4. Press w to scroll through the settings. 5. T urn w to increase or to decrease the bass, midrange, or treble. If a station is weak or noisy , de[...]

Adjusting the Speakers (Balance/Fade) T o adjust the balance or fade: 1. Press w to enter the main menu. 2. T urn w until BALANCE ‐ F ADER displays. 3. Press w to enter the settings. 4. Press w to scroll to BALANCE or FADER. 5. T urn w to adjust the BALANCE to the right or the left speakers and the F ADER to the front or the rear speakers. 6. Pre[...]

MSG (Message) : Displays if the current RDS station has a message. The message can display the artist, song title, call in phone numbers, etc. If the entire message does not display , parts of the message appear every three seconds until the message is completed. MSG disappears from the display once the completed message has displayed. T o display [...]

Activating Program T ype (PTY) Stations (RDS and XM ™ ) PTY lets the radio search for stations with specific types of music. When this feature is turned on, the PTYs display above the pushbuttons in place of the programmed preset stations. Not all stations support PTYs and the radio may not go to all of the stations with that music type when pres[...]

Radio Message THEFTLOCK : Displays when the THEFTLOCK ® system has been activated. T ake the vehicle to your dealer/retailer for service. XM Satellite Radio Service XM is a satellite radio service that is based in the 48 contiguous United States and 10 Canadian provinces. XM Satellite Radio has a wide variety of programming and commercial-free mus[...]

F3 RDM (Random) : Press to listen to the tracks in a random, rather than sequential order . RANDOM displays. Press again to turn off random play . RANDOM disappears from the display . F4 RPT (Repeat) : Press to hear a track over again. REPEA T displays. Press again to turn off repeat play . REPEA T disappears from the display . F6 DISP (Display) : [...]

If the radio is on, the lased CD loaded begins to play automatically . CD displays and the number of the CD and the track number displays. F1 DISC n (Down): Press to go to the previous CD. F2 DISC m (Up): Press to go to the next CD. F3 CD REV { (Reverse): Press to go to the previous track. Press and hold to reverse quickly within the track. Release[...]

Playing an MP3 CD-R Disc Radios with the MP3 feature are capable of playing an MP3 CD-R disc. For more information on how to play an MP3 CD-R disc, see Using an MP3 on page 4 ‑ 108 later in this section. Care of CDs The sound quality of the CD player can be reduced because of: . The CD ‐ R quality . . The method of recording the CD ‐ R. . The[...]

. The air is very humid. If so, wait about an hour and try again. . The format of the CD might not be compatible. See Using an MP3 on page 4 ‑ 108 later in this section. . A problem may have occurred while burning the CD. . The label could be caught in the CD player . If the CD is not playing correctly for any other reason, try a known good CD. I[...]

Using an MP3 MP3 CD-R Disc MP3 Format The MP3 player will only play CD-R discs. It can read and play a maximum of: . 50 folders. . 1 1 folders in depth . 50 playlists . 10 sessions . 255 files All folders, playlists, sessions and files over the maximum are ignored. When recording an MP3 disc, make sure that: . Playlists use an .m3u or .wpl extensio[...]

CD's that do not have playlists play the tracks in the following order: 1. The first file in the root directory plays. 2. After all files from the root directory have played, files in the folders play . 3. After playing the last file from the last folder , play restarts with the first file in the root directory . Preprogrammed Playlists Prepro[...]

Playing an MP3 F1 r (Previous Folder): Press to go to the first track in the previous folder . Press and hold F1 r to reverse quickly within a track. Release to resume playback. REV and the elapsed time of the track displays. Pressing F1 r while in folder random mode goes to the previous folder and plays the tracks in that folder in random order . [...]

F4 RPT (Repeat) : Single tracks or folders can be repeated. . T o repeat the current track, press and release F4 RPT until RPT TRCK displays. . T o repeat the tracks in the current folder , press and release F4 RPT until RPT FLDR displays. . T o turn repeat off, press and release F4 RPT until NORMAL displays. F6 DISP (Display) : Press to switch bet[...]

XM Radio Messages XL (Explicit Language Channels) : These channels, or any others, can be blocked at a customer's request, by calling 1-800-852-XMXM (9696). XM Updating : The encryption code in the receiver is being updated, and no action is required. This process should take no longer than 30 seconds. No XM Signal : The system is functioning [...]

Check XM Receivr : If this message does not clear within a short period of time, the receiver could have a fault. Consult with your dealer/retailer . XM Not A vailable : If this message does not clear within a short period of time, the receiver could have a fault. Consult with your dealer/retailer . Navigation/Radio System For vehicles with a navig[...]

Bluetooth Controls Use the buttons located on the steering wheel to operate the in ‐ vehicle Bluetooth system. See Audio Steering Wheel Controls on page 4 ‑ 134 for more information. b g (Push T o T alk) : Press to answer incoming calls, to confirm system information, and to start speech recognition. Pairing A Bluetooth enabled cell phone must [...]

5. The system prompts for a name for the phone. Use a name that best describes the phone. This name will be used to indicate which phone is connected. The system then confirms the name provided. 6. The system responds with “ <Phone name> has been successfully paired ” after the pairing process is complete. 7. Repeat Steps 1 through 7 for [...]

Storing Name T ags The system can store up to thirty phone numbers as name tags that are shared between the Bluetooth and OnStar systems. The system uses the following commands to store and retrieve phone numbers: . Store . Digit Store . Directory Using the Store Command The store command allows a phone number to be stored without entering the digi[...]

3. Say the first digit to be stored. The system will repeat back the digit it heard followed by a tone. Continue entering digits until the number to be stored is complete. . If an unwanted number is recognized by the system, say “ Clear ” at any time to clear the last number . . T o hear all of the numbers recognized by the system, say “ V er[...]

3. Say the name tag to be deleted. The system responds with “ Would you like to delete, <name tag>? Please say yes or no ” . . If the name tag is correct, say “ Y es ” to delete the name tag. The system responds with “ OK, deleting <name tag>, returning to the main menu. ” . If the name tag is incorrect, say “ No ” . The[...]

Using the Digit Dial Command 1. Press and hold b g for two seconds. The system responds with “ Ready ” followed by a tone. 2. Say “ Digit Dial ” . The system responds with “ Digit dial using <phone name>, please say the first digit to dial ” followed by a tone. 3. Say the digit to be dialed one at a time. Following each digit, the[...]

Using the Re ‐ dial Command 1. Press and hold b g for two seconds. The system responds with “ Ready ” followed by a tone. 2. After the tone, say “ Re ‐ dial ” . The system responds with “ Re ‐ dial using <phone name> ” and dials the last number called from the connected Bluetooth phone. Once connected, the person called will[...]

T o Mute a call 1. Press b g . The system responds with “ Ready ” followed by a tone. 2. Say “ Mute Call ” . The system responds with “ Call muted ” . T o Cancel Mute 1. Press b g . The system responds with “ Ready ” followed by a tone. 2. After the tone, say “ Mute Call ” . The system responds with “ Resuming call ” . T ran[...]

Dual T one Multi-Frequency (DTMF) T ones The in ‐ vehicle Bluetooth system can send numbers and numbers stored as name tags during a call. This is used when calling a menu driven phone system. Account numbers can be programmed into the phonebook for retrieval during menu driven calls. Sending a Number During a Call 1. Press b g . The system respo[...]

Other Information The Bluetooth ® word mark and logos are owned by the Bluetooth ® SIG, Inc. and any use of such marks by General Motors is under license. Other trademarks and trade names are those of their respective owners. See Radio Frequency Statement on page 8 ‑ 18 for FCC information. Phone (Navigation) The navigation system has Bluetooth[...]

T o use the phone to connect or pair to the navigation system: 1. Press the CONFIG hard key . 2. Select the E (Bluetooth ® ) screen button. 3. Select the Receive screen button. Use your phone's search feature to select the vehicle from the phone's list of Bluetooth ® devices found. 4. Follow the instructions on the screen of the phone t[...]

{ (Page Up): Select to scroll up the list one page at a time. z (Page Down): Select to scroll down the list one page at a time. F (Cancel): Select to return to the setup screen. Registered Device : Select to display a list of all Bluetooth ® phones that have been registered (connected) to the vehicle. From this list you can set your default device[...]

Bluetooth ® Phone Screen This information on this screen depends on the information received from the phone. Some phones may not support this feature. While in this screen, use the different features to dial or to make a call. Press the AUX hard key to get to the BLUETOOTH PHONE screen. The screen displays even if the phone is not connected. If th[...]

g (Phone Book): This screen button goes to the phone book screen. From this screen names can be stored in the Bluetooth ® system to be used to dial calls from. This address book is independent of the phone ’ s address book and data cannot be transferred from the Bluetooth ® phone book to the phone ’ s address book or vise versa. V (Send/End C[...]

Phone Book Screen This screen allows access to your Bluetooth ® Phone Book where names and phone numbers are stored. Information in this screen must be entered using the New screen button or by copying and adding the number from the last 10 dialed or received options. This phone book is stored on the Bluetooth ® system. Phone book entries can not[...]

4. A nametag to the entry to work with the voice recognition. Up to 20 nametags can be used for phone book entries in use at a time. 5. After entering the information, touch the OK screen button. T o delete a phone book entry: 1. Select the g (phone book) screen button. 2. Select the name to be deleted. 3. Select the Edit screen button. 4. Select t[...]

Last 10 Calls Screen This screen shows either the last 10 calls that have been placed or the last 10 calls received by the Bluetooth ® system. The newest calls are at the top of the list. { (Page Up) : Scrolls up the list one page at a time. y (Scroll Up) : Scrolls up the list one entry at a time. z (Scroll Down) : Scrolls down the list one entry [...]

Accessing the Main Menu T o access the main menu: 1. Press CNFG or w to enter the main menu. 2. T urn w to scroll through the menu items. The main menu consists of the following menu items: . e BASS - MID - TREBLE . x BALANCE - F ADER . e EQ EQUALIZER . H/A (HOME/A W A Y) PRESETS . AUTOSTORE PRESETS . CA T CA TEGORY . T A TRAFFIC ANNOUNCE . RECALL [...]

CA T (Category) : This item allows radio stations based on preset categories to be selected. See “ Activating Program T ype (PTY) Stations ” under Radio(s) on page 4 ‑ 95 for more information. T A (T raffic Announcement) : This item allows the T A feature to be turned on and off. See “ T A (T raffic Announcement) ” under Radio(s) on page [...]

3. Press w to enter the language settings and then turn w to scroll through the following available langauges: . ENGLISH . GERMAN . FRENCH . SP ANISH . JAP ANESE 4. Press w to set the langauge. 5. Press F6 to exit the display . T o return to the original display , repeatedly press F6 or wait for the display to time out. SETUP : The following submen[...]

DRIVER EXIT SETTINGS The following submenu displays when this item is selected: . RECALL EXIT SETTINGS . STORE EXIT SETTINGS For more information on the DRIVER EXIT SETTINGS submenu item, see “ Recalling Exit Settings ” and “ Storing Exit Settings ” under Memory Seat, Mirrors and Steering Wheel on page 3 ‑ 75 . CONFIGURE DISPLA Y KEYS (Ba[...]

Some audio controls can be adjusted at the steering wheel. ¨ SEEK © : Press to go to the next or previous radio station with a strong signal in the selected band while listening to the radio. Press ¨ or © to go to the next or previous track while a CD is playing, SRCE (Source) : Press to select between AM, FM, XM ™ , or CD. SCAN : Press and h[...]

Radio Reception Frequency interference and static can occur during normal radio reception if items such as cell phone chargers, vehicle convenience accessories, and external electronic devices are plugged into the accessory power outlet. If there is interference or static, unplug the item from the accessory power outlet. AM The range for most AM st[...]

Backglass Antenna The AM-FM antenna is integrated with the rear window defogger , located in the rear window . Make sure that the inside surface of the rear window is not scratched and that the lines on the glass are not damaged. If the inside surface is damaged, it could interfere with radio reception. For proper radio reception, the antenna conne[...]

2 NOTES 4-138[...]

Section 5 Driving Y our V ehicle Y our Driving, the Road, and the V ehicle . . . . . . . . . . 5-2 Defensive Driving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2 D r u n k D r i v i n g ... ................................ 5 - 2 Control of a V ehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3 B r a k i n g ..[...]

Y our Driving, the Road, and the V ehicle Defensive Driving Defensive driving means “ always expect the unexpected. ” The first step in driving defensively is to wear your safety belt — See Safety Belts: They Are for Everyone on page 2 ‑ 8 . { W ARNING: Assume that other road users (pedestrians, bicyclists, and other drivers) are going to b[...]

Police records show that almost 40 percent of all motor vehicle-related deaths involve alcohol. In most cases, these deaths are the result of someone who was drinking and driving. In recent years, more than 17,000 annual motor vehicle-related deaths have been associated with the use of alcohol, with about 250,000 people injured. For persons under 2[...]

Braking See Brake System Warning Light on page 4 ‑ 58 . Braking action involves perception time and reaction time. Deciding to push the brake pedal is perception time. Actually doing it is reaction time. Average reaction time is about three ‐ fourths of a second. But that is only an average. It might be less with one driver and as long as two o[...]

Antilock Brake System (ABS) This vehicle has the Antilock Brake System (ABS), an advanced electronic braking system that helps prevent a braking skid. When the engine is started and the vehicle begins to drive away , ABS checks itself. A momentary motor or clicking noise might be heard while this test is going on, and it might even be noticed that [...]

Braking in Emergencies ABS allows the driver to steer and brake at the same time. In many emergencies, steering can help more than even the very best braking. Brake Assist This vehicle has a Brake Assist feature designed to assist the driver in stopping or decreasing vehicle speed in emergency driving conditions. This feature uses the stability sys[...]

StabiliT rak comes on automatically whenever the vehicle is started. T o help assist with directional control of the vehicle, always leave the system on. StabiliT rak can be turned off, however , by using the T raction Control System (TCS)/StabiliT rak button. See T raction Control System (TCS) on page 5 ‑ 9 . If cruise control is being used when[...]

T o assist with directional control of the vehicle, always leave the system on. Stability control can be turned off however , by using the TC button. See T raction Control System (TCS) on page 5 ‑ 9 . The ST ABILITY SYS OFF message will be displayed on the DIC. See DIC Warnings and Messages on page 4 ‑ 76 . If there is a problem detected with E[...]

Enhanced StabiliT rak and T raction Control Mode Selection Enhanced StabiliT rak can be operated in T ouring Mode. It can also be turned off. The TC button is used to change stability control modes (T ouring or Off) as well as to turn traction control on or off. See T raction Control System (TCS) on page 5 ‑ 9 . The following information describe[...]

The system may be heard or felt while it is working, but this is normal. This warning light comes on if there is a problem with TCS. See T raction Control System (TCS) Warning Light on page 4 ‑ 60 . When this warning light is on, the system will not limit wheel spin. Adjust your driving accordingly . TCS automatically comes on whenever the vehicl[...]

Magnetic Ride Control ™ V ehicles with this feature automatically adjust the ride of the vehicle based on driving conditions. Magnetic Ride Control monitors the suspension system to determine the proper system response. If the controller detects a problem within the system, the DIC will display a SERVICE SUSPENSION SYS message. See DIC Warnings a[...]

During some operating conditions, the active steering might deactivate to protect the system from damage. Y ou might notice that the center position of the steering wheel is changed. Unless there is a SERVICE STEERING SYS message, the system will return to normal operation as soon as the condition ceases, usually within a very short period of time.[...]

T ry to adjust the speed so you can drive through the curve. Maintain a reasonable, steady speed. W ait to accelerate until out of the curve, and then accelerate gently into the straightaway . T o help you steer in the direction you want to go, during certain sharp or sudden cornering maneuvers, gear selection is controlled. This will maximize the [...]

Off-Road Recovery The vehicle's right wheels can drop off the edge of a road onto the shoulder while driving. If the level of the shoulder is only slightly below the pavement, recovery should be fairly easy . Ease off the accelerator and then, if there is nothing in the way , steer so that the vehicle straddles the edge of the pavement. T urn [...]

Skidding In a skid, a driver can lose control of the vehicle. Defensive drivers avoid most skids by taking reasonable care suited to existing conditions, and by not overdriving those conditions. But skids are always possible. The three types of skids correspond to the vehicle's three control systems. In the braking skid, the wheels are not rol[...]

Driving at Night Night driving is more dangerous than day driving because some drivers are likely to be impaired — by alcohol or drugs, with night vision problems, or by fatigue. Night driving tips include: . Drive defensively . . Do not drink and drive. . Reduce headlamp glare by adjusting the inside rearview mirror . . Slow down and keep more s[...]

{ W ARNING: Wet brakes can cause crashes. They might not work as well in a quick stop and could cause pulling to one side. Y ou could lose control of the vehicle. After driving through a large puddle of water or a car/vehicle wash, lightly apply the brake pedal until the brakes work normally . Flowing or rushing water creates strong forces. Driving[...]

Before Leaving on a Long T rip T o prepare your vehicle for a long trip, consider having it serviced by your dealer/retailer before departing. Things to check on your own include: . Windshield Washer Fluid: Reservoir full? Windows clean — inside and outside? . Wiper Blades: In good shape? . Fuel, Engine Oil, Other Fluids: All levels checked? . La[...]

Hill and Mountain Roads Driving on steep hills or through mountains is different than driving on flat or rolling terrain. Tips for driving in these conditions include: . Keep the vehicle serviced and in good shape. . Check all fluid levels and brakes, tires, cooling system, and transmission. . Going down steep or long hills, shift to a lower gear .[...]

Winter Driving Driving on Snow or Ice Drive carefully when there is snow or ice between the tires and the road, creating less traction or grip. Wet ice can occur at about 0°C (32°F) when freezing rain begins to fall, resulting in even less traction. Avoid driving on wet ice or in freezing rain until roads can be treated with salt or sand. Drive w[...]

Blizzard Conditions Being stuck in snow can be in a serious situation. Stay with the vehicle unless there is help nearby . If possible, use the Roadside Service on page 8 ‑ 8 . T o get help and keep everyone in the vehicle safe: . T urn on the Hazard Warning Flashers on page 4 ‑ 3 . . T ie a red cloth to an outside mirror . { W ARNING: Snow can[...]

T o save fuel, run the engine for only short periods as needed to warm the vehicle and then shut the engine off and close the window most of the way to save heat. Repeat this until help arrives but only when you feel really uncomfortable from the cold. Moving about to keep warm also helps. If it takes some time for help to arrive, now and then when[...]

Rocking Y our V ehicle to Get It Out T urn the steering wheel left and right to clear the area around the front wheels. T urn off any traction or stability system. Shift back and forth between R (Reverse) and a forward gear , spinning the wheels as little as possible. T o prevent transmission wear , wait until the wheels stop spinning before shifti[...]

Tire and Loading Information Label Example Label A vehicle specific Tire and Loading Information label is attached to the vehicle's center pillar (B-pillar). With the driver's door open, you will find the label attached below the door lock post (striker). The T ire and Loading Information label shows the number of occupant seating positio[...]

Steps for Determining Correct Load Limit 1. Locate the statement “ The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs ” on your vehicle's placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle. 3. Subtract the combined weight of the driver and passengers from[...]

Example 1 Item Description T otal A V ehicle Capacity Weight for Example 1 = 1,000 lbs (453 kg) B Subtract Occupant Weight @ 150 lbs (68 kg) × 2 = 300 lbs (136 kg) C Available Occupant and Cargo Weight = 700 lbs (317 kg) Example 2 Item Description T otal A V ehicle Capacity Weight for Example 2 = 1,000 lbs (453 kg) B Subtract Occupant Weight @ 150[...]

Example 3 Item Description T otal A V ehicle Capacity Weight for Example 3 = 1,000 lbs (453 kg) B Subtract Occupant Weight @ 200 lbs (91 kg) × 5 = 1,000 lbs (453 kg) C Available Cargo Weight = 0 lbs (0 kg) Refer to your vehicle's T ire and Loading Information label for specific information about your vehicle's capacity weight and seating[...]

rear axles, called the Gross Axle Weight Rating (GA WR). Never exceed the GVWR or the GAWR for either the front or rear axle. { W ARNING: Do not load the vehicle any heavier than the Gross V ehicle Weight Rating (GVWR), or either the maximum front or rear Gross Axle Weight Rating (GA WR). If you do, parts on the vehicle can break, and it can change[...]

T owing T owing Y our V ehicle Consult your dealer/retailer or a professional towing service if the disabled vehicle needs to be towed. See Roadside Service on page 8 ‑ 8 . T o tow the vehicle behind another vehicle for recreational purposes (such as behind a motorhome), see Recreational V ehicle T owing following. Recreational V ehicle T owing R[...]

Dinghy T owing Notice: If the vehicle is towed with all four wheels on the ground, the drivetrain components could be damaged. The repairs would not be covered by the vehicle warranty . Do not tow the vehicle with all four wheels on the ground. The vehicle was not designed to be towed with all four wheels on the ground. If the vehicle must be towed[...]

3. Firmly set the parking brake. See Parking Brake on page 3 ‑ 33 . 4. Put the transmission in P (Park). 5. Secure the vehicle to the dolly following the manufacturer's instructions. 6. Use an adequate clamping device designed for towing to ensure that the front wheels are locked into the straight position. 7. T urn the ignition to LOCK/OFF [...]

T railering is different than just driving the vehicle by itself. T railering means changes in handling, acceleration, braking, durability and fuel economy . Successful, safe trailering takes correct equipment, and it has to be used properly . The following information has many time-tested, important trailering tips and safety rules. Many of these [...]

Three important considerations have to do with weight: . The weight of the trailer . . The weight of the trailer tongue. . The total weight on the vehicle's tires. Weight of the T railer How heavy can a trailer safely be? It should never weigh more than 1,000 lbs (450 kg). But even that can be too heavy . It depends on how the rig is used. For[...]

After loading the trailer , weigh the trailer and then the tongue, separately , to see if the weights are proper . If they are not, adjustments might be made by moving some items around in the trailer . T otal Weight on the V ehicle's Tires Be sure the vehicle's tires are inflated to the upper limit for cold tires. These numbers can be fo[...]

T railer Brakes Does the trailer have its own brakes? Be sure to read and follow the instructions for the trailer brakes so they are installed, adjusted and maintained properly . Because the vehicle has StabiliTrak ® , do not try to tap into the vehicle's hydraulic brake system. If you do, both brake systems will not work well, or at all. T r[...]

Backing Up Hold the bottom of the steering wheel with one hand. Then, to move the trailer to the left, move that hand to the left. T o move the trailer to the right, move your hand to the right. Always back up slowly and, if possible, have someone guide you. Making T urns Notice: Making very sharp turns while trailering could cause the trailer to c[...]

Driving On Grades Reduce speed and shift to a lower gear before starting down a long or steep downgrade. If the transmission is not shifted down, the brakes might have to be used so much that they would get hot and no longer work well. On a long uphill grade, shift down and reduce the vehicle's speed to around 45 mph (70 km/h) to reduce the po[...]

Leaving After Parking on a Hill 1. Apply and hold the brake pedal while you: . Start the engine . Shift into a gear . Release the parking brake 2. Let up on the brake pedal. 3. Drive slowly until the trailer is clear of the chocks. 4. Stop and have someone pick up and store the chocks. Maintenance When T railer T owing The vehicle needs service mor[...]

Section 6 Service and Appearance Care Service ......... ........................... ......... 6-4 Accessories and Modifications . . . . . . . . . . . . . . . . . . 6-4 California Proposition 65 Warning . . . . . . . . . . . . . . . 6-5 California Perchlorate Materials R e q u i r e m e n t s ................................. 6 - 5 Doing Y our Own S[...]

Section 6 Service and Appearance Care T ire Pressure Monitor System . . . . . . . . . . . . . . . . . 6-62 T ire Pressure Monitor Operation . . . . . . . . . . . . . . . 6-64 T ire Inspection and Rotation . . . . . . . . . . . . . . . . . . . 6-67 When It Is T ime for New Tires . . . . . . . . . . . . . . . . . 6-69 Buying New T ires . . . . . . . [...]

Section 6 Service and Appearance Care V ehicle Identification ............................ 6-1 16 V ehicle Identification Number (VIN) . . . . . . . . . . . 6-1 16 Service Parts Identification Label . . . . . . . . . . . . . 6-1 16 Electrical System ........ ..................... ... 6-1 16 Add-On Electrical Equipment . . . . . . . . . . . . . . . [...]

Service For service and parts needs, visit your dealer/retailer . Y ou will receive genuine GM parts and GM-trained and supported service people. Genuine GM parts have one of these marks: Accessories and Modifications When non ‐ dealer/non ‐ retailer accessories are added to the vehicle, they can affect vehicle performance and safety , includin[...]

California Proposition 65 W arning Most motor vehicles, including this one, contain and/or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Engine exhaust, many parts and systems, many fluids, and some component wear by-products contain and/or emit these chemicals. California Perchlorate [...]

Keep a record with all parts receipts and list the mileage and the date of any service work performed. See Maintenance Record on page 7 ‑ 13 . Adding Equipment to the Outside of the V ehicle Things added to the outside of the vehicle can affect the airflow around it. This can cause wind noise and can affect fuel economy and windshield washer perf[...]

Gasoline Octane If the vehicle has the 3.6L V6 engine (VIN Code V), use regular unleaded gasoline with a posted octane rating of 87 or higher . If the octane rating is less than 87, an audible knocking noise, commonly referred to as spark knock, might be heard when driving. If this occurs, use a gasoline rated at 87 octane or higher as soon as poss[...]

Additives T o provide cleaner air , all gasolines in the United States are now required to contain additives that help prevent engine and fuel system deposits from forming, allowing the emission control system to work properly . In most cases, nothing should have to be added to the fuel. However , some gasolines contain only the minimum amount of a[...]

T o check the fuel availability , ask an auto club, or contact a major oil company that does business in the country where you will be driving. Filling the T ank { W ARNING: Fuel vapor burns violently and a fuel fire can cause bad injuries. T o help avoid injuries to you and others, read and follow all the instructions on the fuel pump island. Turn[...]

While refueling, hang the tethered fuel cap from the hook on the fuel door . { W ARNING: Fuel can spray out on you if you open the fuel cap too quickly . If you spill fuel and then something ignites it, you could be badly burned. This spray can happen if the tank is nearly full, and is more likely in hot weather . Open the fuel cap slowly and wait [...]

{ W ARNING: If a fire starts while you are refueling, do not remove the nozzle. Shut off the flow of fuel by shutting off the pump or by notifying the station attendant. Leave the area immediately . Notice: If you need a new fuel cap, be sure to get the right type. Y our dealer/retailer can get one for you. If you get the wrong type, it may not fit[...]

Checking Things Under the Hood { W ARNING: An electric fan under the hood can start up and injure you even when the engine is not running. Keep hands, clothing, and tools away from any underhood electric fan. { W ARNING: Things that burn can get on hot engine parts and start a fire. These include liquids like fuel, oil, coolant, brake fluid, windsh[...]

2. Then go to the front of the vehicle and find the secondary hood release lever . The lever is located under the front edge of the grille near the center . Push the release lever up and raise the hood. Before closing the hood, be sure all the filler caps are on properly . Then pull the hood down and close it firmly . Engine Compartment Overview Y [...]

3.6L V6 Engine 6-14[...]

After you have removed the sight shields (if equipped) on the 3.6L V6 engine, here is what you will see: A. Underhood Fuse Block. See Underhood Fuse Block on page 6 ‑ 1 18 . B. Remote Negative (-) T erminal. See Jump Starting on page 6 ‑ 40 . C. Remote Positive (+) T erminal. See Jump Starting on page 6 ‑ 40 . D. Battery . See Battery on page[...]

4.6L V8 Engine 6-16[...]

After you have removed the sight shields (if equipped) on the 4.6L V8 engine, here is what you will see: A. Remote Negative (-) T erminal. See Jump Starting on page 6 ‑ 40 . B. Remote Positive (+) T erminal. See Jump Starting on page 6 ‑ 40 . C. Battery . See Battery on page 6 ‑ 40 . D. Passenger Compartment Air Filter . See Passenger Compart[...]

Engine Oil Checking Engine Oil It is a good idea to check the engine oil level at each fuel fill. In order to get an accurate reading, the oil must be warm and the vehicle must be on level ground. The engine oil dipstick handle is a yellow loop. See Engine Compartment Overview on page 6 ‑ 13 for the location of the engine oil dipstick. 1. T urn o[...]

If the oil is below the cross-hatched area at the tip of the dipstick, add at least one quart/liter of the recommended oil. This section explains what kind of oil to use. For engine oil crankcase capacity , see Capacities and Specifications on page 6 ‑ 130 . Notice: Do not add too much oil. If the engine has so much oil that the oil level gets ab[...]

What Kind of Engine Oil to Use Look for three things: . GM4718M This vehicle's engine requires a special oil meeting GM Standard GM4718M. Oils meeting this standard may be identified as synthetic. However , not all synthetic oils will meet this GM standard. Use only an oil that meets GM Standard GM4718M. Notice: Using oils that do not have the[...]

Engine Oil Additives / Engine Oil Flushes Do not add anything to the oil. The recommended oils with the starburst symbol that meet GM standards are all that is needed for good performance and engine protection. Engine oil system flushes are not recommended and could cause engine damage not covered by the vehicle warranty . Engine Oil Life System Wh[...]

How to Reset the Engine Oil Life System The Engine Oil Life System calculates when to change the engine oil and filter based on vehicle use. Whenever the oil is changed, reset the system so it can calculate when the next oil change is required. If a situation occurs where the oil is changed prior to a CHANGE ENGINE OIL SOON message in the DIC being[...]

Engine Air Cleaner/Filter 4.6L V8 Engine shown, 3.6L V6 Engine similar The engine air cleaner/filter is in the engine compartment on the driver's side of the vehicle, near the front. See Engine Compartment Overview on page 6 ‑ 13 for more information on locating the air cleaner/filter . When to Inspect the Engine Air Cleaner/Filter Inspect t[...]

How to Inspect the Engine Air Cleaner/Filter T o inspect the air cleaner/filter remove the filter from the vehicle and lightly shake the filter to release loose dust and dirt. If the filter remains caked with dirt, a new filter is required. T o inspect or replace the filter in the 3.6L V6 or 4.6L V8 engines, do the following: 1. Remove the two scre[...]

{ W ARNING: Operating the engine with the air cleaner/filter off can cause you or others to be burned. The air cleaner not only cleans the air; it helps to stop flames if the engine backfires. Use caution when working on the engine and do not drive with the air cleaner/filter off. Notice: If the air cleaner/filter is off, dirt can easily get into t[...]

Cooling System The cooling system allows the engine to maintain the correct working temperature. 3.6L V6 Engine shown, 4.6L V8 Engine similar A. Electric Engine Cooling Fan(s) (Out of view) B. Mechanical Engine Cooling Fan (If equipped) (Out of view) C. Coolant Surge T ank and Pressure Cap { W ARNING: An electric engine cooling fan under the hood c[...]

{ W ARNING: Heater and radiator hoses, and other engine parts, can be very hot. Do not touch them. If you do, you can be burned. Do not run the engine if there is a leak. If you run the engine, it could lose all coolant. That could cause an engine fire, and you could be burned. Get any leak fixed before you drive the vehicle. Notice: Using coolant [...]

What to Use { W ARNING: Adding only plain water to the cooling system can be dangerous. Plain water , or some other liquid such as alcohol, can boil before the proper coolant mixture will. The vehicle's coolant warning system is set for the proper coolant mixture. With plain water or the wrong mixture, the engine could get too hot but you woul[...]

Checking Coolant The vehicle must be on a level surface when checking the coolant level. The coolant surge tank and pressure cap are located on the driver's side of the vehicle, toward the rear of the engine compartment. See Engine Compartment Overview on page 6 ‑ 13 for more information on location. Check to see if coolant is visible in the[...]

How to Add Coolant to the Surge T ank { W ARNING: Y ou can be burned if you spill coolant on hot engine parts. Coolant contains ethylene glycol and it will burn if the engine parts are hot enough. Do not spill coolant on a hot engine. { W ARNING: Steam and scalding liquids from a hot cooling system can blow out and burn you badly . They are under p[...]

2. Then keep turning the pressure cap slowly , and remove it. 3. Fill the coolant surge tank with the proper DEX-COOL ® coolant mixture, to slightly above the FULL COLD/FROID line on the side of the coolant surge tank. 6-31[...]

4. With the coolant surge tank pressure cap off, start the engine and let it run until you can feel the upper radiator hose getting hot. The upper radiator hose is the largest of the hoses which comes out of the radiator , on the passenger side of the vehicle. W atch out for the engine cooling fans. By this time, the coolant level inside the coolan[...]

If Steam Is Coming From The Engine Compartment { W ARNING: Steam from an overheated engine can burn you badly , even if you just open the hood. Stay away from the engine if you see or hear steam coming from it. T urn it off and get everyone away from the vehicle until it cools down. W ait until there is no sign of steam or coolant before you open t[...]

If the engine coolant temperature gage is no longer in the overheat zone or an overheat warning no longer displays, the vehicle can be driven. Continue to drive the vehicle slow for about 10 minutes. Keep a safe vehicle distance from the car in front of you. If the warning does not come back on, continue to drive normally . If the warning continues[...]

Power Steering Fluid See Engine Compartment Overview on page 6 ‑ 13 for reservoir location. When to Check Power Steering Fluid It is not necessary to regularly check power steering fluid unless you suspect there is a leak in the system or you hear an unusual noise. A fluid loss in this system could indicate a problem. Have the system inspected an[...]

Windshield W asher Fluid What to Use When you need windshield washer fluid, be sure to read the manufacturer's instructions before use. If you will be operating your vehicle in an area where the temperature may fall below freezing, use a fluid that has sufficient protection against freezing. Adding W asher Fluid The CHECK WASHER FLUID message [...]

Brakes Brake Fluid The brake master cylinder reservoir is filled with DOT 3 brake fluid. See Engine Compartment Overview on page 6 ‑ 13 for reservoir location and access. There are only two reasons why the brake fluid level in the reservoir might go down: . The brake fluid level goes down because of normal brake lining wear . When new linings are[...]

What to Add DOT 3 brake fluid is recommended. DOT 4 brake fluid is also compatible with the vehicle's brake system parts. However , if DOT 4 fluid is used, it is recommended that the brake hydraulic system be flushed and refilled with new DOT 4 fluid at a regular maintenance service every two years. See Scheduled Maintenance on page 7 ‑ 3 . [...]

{ W ARNING: The brake wear warning sound means that soon the brakes will not work well. That could lead to an accident. When the brake wear warning sound is heard, have the vehicle serviced. Notice: Continuing to drive with worn-out brake pads could result in costly brake repair. Some driving conditions or climates can cause a brake squeal when the[...]

Battery Refer to the replacement number on the original battery label when a new battery is needed. See Engine Compartment Overview on page 6 ‑ 13 for battery location. { DANGER: Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. W as[...]

Notice: Ignoring these steps could result in costly damage to the vehicle that would not be covered by the warranty . T rying to start the vehicle by pushing or pulling it will not work, and it could damage the vehicle. 1. Check the other vehicle. It must have a 12-volt battery with a negative ground system. Notice: If the other vehicle's syst[...]

Y our vehicle has a remote negative ( − ) ground location, as shown in the illustration. It is located on the passenger side front shock tower . See Engine Compartment Overview on page 6 ‑ 13 . Y ou should always use this remote ground location, instead of the terminal on the battery . Notice: If you connect a negative cable to the Engine Contr[...]

{ W ARNING: Using an open flame near a battery can cause battery gas to explode. People have been hurt doing this, and some have been blinded. Use a flashlight if you need more light. Be sure the battery has enough water . Y ou do not need to add water to the battery installed in your new vehicle. But if a battery has filler caps, be sure the right[...]

6. Connect the red positive (+) cable to the positive (+) terminal of the dead battery . Use a remote positive (+) terminal if the vehicle has one. 7. Do not let the other end touch metal. Connect it to the positive (+) terminal of the good battery . Use a remote positive (+) terminal if the vehicle has one. 8. Now connect the black negative ( − [...]

Notice: If the jumper cables are connected or removed in the wrong order , electrical shorting may occur and damage the vehicle. The repairs would not be covered by the vehicle warranty . Always connect and remove the jumper cables in the correct order , making sure that the cables do not touch each other or other metal. Jumper Cable Removal A. Hea[...]

How to Check Lubricant A. Drain Plug B. Fill Plug T o get an accurate reading, the vehicle should be on a level surface. If the level is below the bottom of the filler plug hole, located on the transfer case, you'll need to add some lubricant. Add enough lubricant to raise the level to the bottom of the filler plug hole. Use care not to overti[...]

How to Check Lubricant T o get an accurate reading, the vehicle should be on a level surface. If the level is below the bottom of the filler plug hole, located on the rear axle, you'll need to add some lubricant. Add enough lubricant to raise the level to the bottom of the filler plug hole. What to Use Refer to the Maintenance Schedule to dete[...]

How to Check Lubricant A. Drain Plug B. Filler Plug T o get an accurate reading, the vehicle should be on a level surface. If the level is below the bottom of the filler plug hole, located on the front axle, you may need to add some lubricant. What to Use Refer to the Maintenance Schedule to determine what kind of lubricant to use. See Recommended [...]

Bulb Replacement For the proper type of replacement bulbs, see Replacement Bulbs on page 6 ‑ 50 . For any bulb changing procedure not listed in this section, contact your dealer/retailer . High Intensity Discharge (HID) Lighting { W ARNING: The low beam high intensity discharge lighting system operates at a very high voltage. If you try to servic[...]

Back-Up Lamps T o replace a back-up lamp bulb: 1. Open the trunk. See T runk on page 3 ‑ 15 . 2. Pull out the push pins holding down the top portion of the cloth cover . 3. Fold the cover down slightly and locate the lamp assembly . 4. T urn the socket counterclockwise and pull it straight out to remove it from the lamp assembly . 5. Pull the old[...]

Windshield Wiper Blade Replacement Windshield wiper blades should be inspected for wear or cracking. See Scheduled Maintenance on page 7 ‑ 3 . It's a good idea to clean or replace the wiper blade assembly on a regular basis or when worn. For proper windshield wiper blade length and type, see Maintenance Replacement Parts on page 7 ‑ 1 1 . [...]

Tires Y our new vehicle comes with high-quality tires made by a leading tire manufact urer . If you ever have questions about your tire warranty and where to obtain service, see your vehicle W arranty booklet for details. { W ARNING: . Poorly maintained and improperly used tires are dangerous. . Overloading your tires can cause overheating as a res[...]

Low ‐ Profile Performance Tires If your vehicle has 255/45ZR18 size tires, they are classified as low ‐ profile performance tires. These tires are designed for very responsive driving on wet or dry pavement. Y ou may also notice more road noise with low ‐ profile performance tires and that they tend to wear faster . These performance tires ar[...]

Tire Sidewall Labeling Useful information about a tire is molded into its sidewall. The examples below show a typical passenger vehicle tire and a compact spare tire sidewall. Passenger (P ‐ Metric) Tire Example (A) Tire Size : The tire size is a combination of letters and numbers used to define a particular tire's width, height, aspect rati[...]

(E) Tire Ply Material : The type of cord and number of plies in the sidewall and under the tread. (F) Uniform Tire Quality Grading (UTQG) : T ire manufacturers are required to grade tires based on three performance factors: treadwear, traction, and temperature resistance. For more information see Uniform Tire Quality Grading on page 6 ‑ 73 . (G) [...]

(B) Tire Ply Material : The type of cord and number of plies in the sidewall and under the tread. (C) Tire Identification Number (TIN) : The letters and numbers following the DOT (Department of Transportation) code is the T ire Identification Number (TIN). The TIN shows the manufacturer and plant code, tire size, and date the tire was manufactured.[...]

(B) Tire Width : The three ‐ digit number indicates the tire section width in millimeters from sidewall to sidewall. (C) Aspect Ratio : A two ‐ digit number that indicates the tire height ‐ to ‐ width measurem ents. For example, if the tire size aspect ratio is 60, as shown in item C of the illustration, it would mean that the tire's s[...]

Cold Tire Pressure : The amount of air pressure in a tire, measured in pounds per square inch (psi) or kilopascals (kPa) before a tire has built up heat from driving. See Inflation - Tire Pressure on page 6 ‑ 60 . Curb Weight : The weight of a motor vehicle with standard and optional equipment including the maximum capacity of fuel, oil, and cool[...]

Occupant Distribution : Designa ted seating positions. Outward Facing Sidewall : The side of an asymmetrical tire that has a particula r side that faces outward when mounted on a vehicle. The side of the tire that contains a whitewall, bears white lettering, or bears manufacture r , brand, and/or model name molding that is higher or deeper than the[...]

V ehicle Maximum Load on the Tire : Load on an individual tire due to curb weight, accessory weight, occupant weight, and cargo weight. V ehicle Placard : A label permanent ly attached to a vehicle showing the vehicle's capacity weight and the original equipment tire size and recommended inflation pressure. See “ T ire and Loading Informatio[...]

When to Check Check your tires once a month or more. Do not forget to check the compact spare tire, if your vehicle has one. The compact spare should be at 60 psi (420 kPa). For additional information regarding the compact spare tire, see Compact Spare Tire on page 6 ‑ 107 . How to Check Use a good quality pocket-type gage to check tire pressure.[...]

High-Speed Operation { W ARNING: Driving at high speeds, 160 km/h (100 mph) or higher , puts an additional strain on tires. Sustained high-speed driving causes excessive heat build up and can cause sudden tire failure. Y ou could have a crash and you or others could be killed. Some high-speed rated tires require inflation pressure adjustment for hi[...]

Accordingly , when the low tire pressure telltale illuminates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly under ‐ inflated tire causes the tire to overheat and can lead to tire failure. Under ‐ inflation also reduces fuel efficiency and tire tread life, and may a[...]

Tire Pressure Monitor Operation This vehicle may have a T ire Pressure Monitor System (TPMS). The TPMS is designed to warn the driver when a low tire pressure condition exists. TPMS sensors are mounted onto each tire and wheel assembly , excluding the spare tire and wheel assembly , if the vehicle has one. The TPMS sensors monitor the air pressure [...]

Factory-installed Tire Inflator Kits use a GM approved liquid tire sealant. Using non-approved tire sealants could damage the TPMS sensors. See Tire Sealant and Compressor Kit (Without Selector Switch) on page 6 ‑ 78 or Tire Sealant and Compressor Kit (With Selector Switch) on page 6 ‑ 87 for information regarding the inflator kit materials and[...]

TPMS Sensor Matching Process Each TPMS sensor has a unique identification code. Any time you replace one or more of the TPMS sensors or rotate your vehicle's tires, the identification codes will need to be matched to the new tire/wheel position. The sensors are matched to the tire/wheel positions in the following order: driver side front tire,[...]

10. After hearing the confirming single horn chirp for the driver side rear tire, a double horn chirp will sound to signal the tire matching mode is no longer active. Press the push ‐ button ignition switch to Acc. 1 1. Set all four tires to the recommended air pressure level as indicated on the tire and loading information label. 12. Put the val[...]

When rotating P235/50R17 size tires or 255/45ZR18 size tires, always use the correct rotation pattern shown here. If the vehicle has a compact spare tire, do not include the compact spare tire in the tire rotation. After the tires have been rotated, adjust the front and rear inflation pressures as shown on the T ire and Loading Information label. S[...]

When It Is Time for New T ires V arious factors, such as maintenance, temperatures, driving speeds, vehicle loading, and road conditions influence when you need new tires. One way to tell when it is time for new tires is to check the treadwear indicators, which will appear when your tires have only 1/16 inch (1.6 mm) or less of tread remaining. Y o[...]

Buying New Tires GM has developed and matched specific tires for your vehicle. The original equipment tires installed on your vehicle, when it was new , were designed to meet General Motors T ire Performance Criteria Specification (TPC Spec) system rating. If you need replacement tires, GM strongly recommends that you get tires with the same TPC Sp[...]

{ W ARNING: Mixing tires could cause you to lose control while driving. If you mix tires of different sizes (other than those originally installed on your vehicle), brands, or types (radial and bias-belted tires), the vehicle may not handle properly , and you could have a crash. Using tires of different sizes (other than those originally installed [...]

Y our vehicle's original equipment tires are listed on the T ire and Loading Information label. See Loading the V ehicle on page 5 ‑ 23 , for more information about the Tire and Loading Information label and its location on your vehicle. Different Size Tires and Wheels If you add wheels or tires that are a different size than your original e[...]

Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: T readwear 200 T raction AA T emperature A The following information relates to the system developed by the United States National Highway T raffic Safety Administration (NHTSA), which grades [...]

T emperature – A, B, C The temperature grades are A (the highest), B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce[...]

If you need to replace any of your wheels, wheel bolts, wheel nuts, or T ire Pressure Monitor System (TPMS) sensors, replace them only with new GM original equipment parts. This way , you will be sure to have the right wheel, wheel bolts, wheel nuts, and TPMS sensors for your vehicle. { W ARNING: Using the wrong replacement wheels, wheel bolts, or [...]

Tire Chains { W ARNING: If your vehicle has P255/45R17, P255/45ZR18, or 255/45ZR18 size tires, do not use tire chains, as there is not enough clearance. T ire chains used on a vehicle without the proper amount of clearance can cause damage to the brakes, suspension, or other vehicle parts. The area damaged by the tire chains could cause you to lose[...]

A rear blowout, particularly on a curve, acts much like a skid and may require the same correction you would use in a skid. In any rear blowout, remove your foot from the accelerator pedal. Get the vehicle under control by steering the way you want the vehicle to go. It may be very bumpy and noisy , but you can still steer . Gently brake to a stop,[...]

Tire Sealant and Compressor Kit (Without Selector Switch) System Identification If the vehicle has the tire sealant and compressor kit shown above, see the operating instructions that follow . If the vehicle has the tire sealant and compressor kit shown above, follow the operating instructions under “ T ire Sealant and Compressor Kit (With Select[...]

{ W ARNING: Idling a vehicle in an enclosed area with poor ventilation is dangerous. Engine exhaust may enter the vehicle. Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled. It can cause unconsciousness and even death. Never run the engine in an enclosed area that has no fresh air ventilation. For more information, see En[...]

Read and follow all of the tire sealant and compressor kit instructions. The kit includes: A. Air Compressor B. T ire Sealant Canister C. Power Plug D. On/Off Button E. Pressure Gage F . Air Only Hose (Black) G. Sealant/Air Hose (Clear) Tire Sealant Read and follow the safe handling instructions on the label adhered to the sealant canister . Check [...]

Using the Tire Sealant and Compressor Kit to T emporarily Seal and Inflate a Punctured Tire When using the tire sealant and compressor kit during cold temperatures, warm the kit in a heated environment for 5 minutes. This will help to inflate the tire faster . Always do a safety check first. See If a Tire Goes Flat on page 6 ‑ 76 . Do not remove [...]

6. Plug the power plug (C) into the accessory power outlet in the vehicle. Unplug all items from other accessory power outlets. See Accessory Power Outlet(s) on page 4 ‑ 42 . If the vehicle has an accessory power outlet, do not use the cigarette lighter . If the vehicle only has a cigarette lighter , use the cigarette lighter . Do not pinch the p[...]

1 1. Unplug the power plug (C) from the accessory power outlet in the vehicle. 12. T urn the sealant/air hose (F) counterclockwise to remove it from the tire valve stem. 13. Replace the tire valve stem cap. 14. Replace the sealant/air hose (F), and the power plug (C) back in their original location. 15. If the flat tire was able to inflate to the r[...]

Using the Tire Sealant and Compressor Kit without Sealant to Inflate a Tire (Not Punctured) T o use the air compressor to inflate a tire with air only and not sealant: Always do a safety check first. See If a Tire Goes Flat on page 6 ‑ 76 . 1. Remove the tire sealant and compressor kit from its storage location. See Tire Sealant and Compressor Ki[...]

8. Plug the power plug (C) into the accessory power outlet in the vehicle. Unplug all items from other accessory power outlets. See Accessory Power Outlet(s) on page 4 ‑ 42 . If the vehicle has an accessory power outlet, do not use the cigarette lighter . If the vehicle only has a cigarette lighter , use the cigarette lighter . Do not pinch the p[...]

Removal and Installation of the Sealant Canister T o remove the sealant canister: 1. Unlock the air only hose (F) from the sealant canister (B) by pulling up on the lever . 2. Pull the air only hose (F) from the sealant canister (B). 3. Unwrap the sealant/air hose (F) from the compressor (A). 4. T urn the sealant canister (B) so the inflator fillin[...]

T o install a new sealant canister: 1. Align the sealant/air hose (F) with the slot in the air compressor . 2. Push the sealant canister (B) down and turn it clockwise. 3. Wrap the sealant/air hose (F) around the air compressor channel to stow it in its original location. 4. Push the air compressor inflator hose (F) onto the sealant canister inlet [...]

If the vehicle has the tire sealant and compressor kit shown above, follow the operating instructions under “ T ire Sealant and Compressor Kit (Without Selector Switch). { W ARNING: Idling a vehicle in an enclosed area with poor ventilation is dangerous. Engine exhaust may enter the vehicle. Engine exhaust contains Carbon Monoxide (CO) which cann[...]

{ W ARNING: Storing the tire sealant and compressor kit or other equipment in the passenger compartment of the vehicle could cause injury . In a sudden stop or collision, loose equipment could strike someone. Store the tire sealant and compressor kit in its original location. If this vehicle has a tire sealant and compressor kit, there may not be a[...]

Tire Sealant Read and follow the safe handling instructions on the label adhered to the sealant canister . Check the tire sealant expiration date on the sealant canister . The sealant canister should be replaced before its expiration date. Replacement sealant canisters are available at your local dealer/retailer . See “ Removal and Installation o[...]

Always do a safety check first. See If a Tire Goes Flat on page 6 ‑ 76 . Do not remove any objects that have penetrated the tire. 1. Remove the tire sealant and compressor kit from its storage location. See Tire Sealant and Compressor Kit Storage on page 6 ‑ 96 . 2. Unwrap the sealant/air hose (F) and the power plug (H). 3. Place the kit on the[...]

10. Inflate the tire to the recommended inflation pressure using the pressure gage (C). The recommended inflation pressure can be found on the T ire and Loading Information label. See Inflation - Tire Pressure on page 6 ‑ 60 . The pressure gage (C) may read higher than the actual tire pressure while the compressor is on. T urn the compressor off [...]

19. Stop at a safe location and check the tire pressure. Refer to Steps 1 through 1 1 under “ Using the Tire Sealant and Compressor Kit without Sealant to Inflate a Tire (Not Punctured). ” If the tire pressure has fallen more than 10 psi (68 kPa) below the recommended inflation pressure, stop driving the vehicle. The tire is too severely damage[...]

3. Place the kit on the ground. 4. Remove the tire valve stem cap from the flat tire by turning it counterclockwise. 5. Attach the air only hose (G) onto the tire valve stem by turning it clockwise until it is tight. 6. Plug the power plug (H) into the accessory power outlet in the vehicle. Unplug all items from other accessory power outlets. See A[...]

14. Replace the air only hose (G) and the power plug (H) and cord back in its original location. 15. Place the equipment in the original storage location in the vehicle. The tire sealant and compressor kit has an accessory adapter located in a compartment on the bottom of its housing that may be used to inflate air mattresses, balls, etc. Removal a[...]

Tire Sealant and Compressor Kit Storage The tire sealant and compressor kit is located in the trunk. 1. Open the trunk. See T runk on page 3 ‑ 15 . 2. Remove the retainer that holds the tire sealant and compressor kit in place. 3. Remove the tire sealant and compressor kit from the foam container . T o store the tire sealant and compressor kit, r[...]

W ARNING: (Continued) T o be even more certain the vehicle will not move, you should put blocks at the front and rear of the tire farthest away from the one being changed. That would be the tire, on the other side, at the opposite end of the vehicle. When the vehicle has a flat tire (B), use the following example as a guide to assist you in the pla[...]

Removing the Spare Tire and T ools The equipment you will need is located in the trunk. T o access to the compact spare tire and jacking equipment: 1. Open the trunk. See T runk on page 3 ‑ 15 for more information. 2. Remove the compact spare tire cover . 3. Pull the stow rod (A) to remove it. 4. T urn the nut (B) holding the jack package contain[...]

The tools you will be using include the jack (A) and the wheel wrench (B). Removing the Flat Tire and Installing the Spare Tire 1. Do a safety check before proceeding. See Changing a Flat Tire on page 6 ‑ 96 for more information. 2. Loosen all of the wheel nuts, but do not remove them yet, using the wheel wrench. T urn the handle about 180 degree[...]

3. Find the vehicle's jacking location using the diagram above and corresponding V – shaped notches located in the plastic molding on the vehicle's frame. The notches in the plastic molding are marked with a triangle shape. 4. Attach the wheel wrench to the jack. { W ARNING: Getting under a vehicle when it is jacked up is dangerous. If [...]

{ W ARNING: Lifting a vehicle and getting under it to do maintenance or repairs is dangerous without the appropriate safety equipment and training. If a jack is provided with the vehicle, it is designed only for changing a flat tire. If it is used for anything else, you or others could be badly injured or killed if the vehicle slips off the jack. I[...]

8. Raise the vehicle by turning the wheel wrench clockwise. Raise the vehicle far enough off the ground for the compact spare tire to fit under the vehicle. 9. Remove all the wheel nuts and the flat tire. { W ARNING: Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time. The wheel could come o[...]

W ARNING: (Continued) to the vehicle. In an emergency , use a cloth or a paper towel to do this; but be sure to use a scraper or wire brush later , if needed, to get all the rust or dirt off. See Changing a Flat Tire on page 6 ‑ 96 . { W ARNING: Never use oil or grease on bolts or nuts because the nuts might come loose. The vehicle's wheel c[...]

14. Lower the vehicle by turning the wheel wrench counterclockwise. Lower the jack completely . { W ARNING: Wheel nuts that are improperly or incorrectly tightened can cause the wheels to become loose or come off. The wheel nuts should be tightened with a torque wrench to the proper torque specification after replacing. Follow the torque specificat[...]

15. T ighten the wheel nuts firmly in a crisscross sequence as shown. Storing a Flat or Spare Tire and T ools { W ARNING: Storing a jack, a tire, or other equipment in the passenger compartment of the vehicle could cause injury . In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place. Full-Size Tire[...]

Compact Spare Tire and T ools Use the following diagram as a guide for storing the compact spare tire and tools in the trunk: A. Compact Spare Tire Cover B. Stow Rod Cap C. Plastic Wing Nut D. Retainer E. Jack Container Package (With Wheel Wrench and Jack) F . Compact Spare T ire G. Foam Support H. Bolt 1. Open the trunk. See T runk on page 3 ‑ 1[...]

Compact Spare Tire { W ARNING: Driving with more than one compact spare tire at a time could result in loss of braking and handling. This could lead to a crash and you or others could be injured. Use only one compact spare tire at a time. Although the compact spare tire was fully inflated when the vehicle was new , it can lose air after a time. Che[...]

Appearance Care Interior Cleaning The vehicle's interior will continue to look its best if it is cleaned often. Although not always visible, dust and dirt can accumulate on the upholstery . Dirt can damage carpet, fabric, leather , and plastic surfaces. Regular vacuuming is recommended to remove particles from the upholstery . It is important [...]

Do not clean the vehicle using: . A knife or any other sharp object to remove a soil from any interior surface. . A stiff brush. It can cause damage to the vehicle's interior surfaces. . Heavy pressure or aggressive rubbing with a cleaning cloth. Use of heavy pressure can damage the interior and does not improve the effectivene ss of soil remo[...]

If any of the soil remains, a commercial fabric cleaner or spot lifter may be necessary . When a commercial upholstery cleaner or spot lifter is to be used, test a small hidden area for colorfastness first. If the locally cleaned area gives any impression that a ring formation may result, clean the entire surface. After the cleaning process has bee[...]

Wood Panels Use a clean cloth moistened in warm, soapy water (use mild dish washing soap). Dry the wood immediately with a clean cloth. Speaker Covers V acuum around a speaker cover gently , so that the speaker will not be damaged. Clean spots with just water and mild soap. Care of Safety Belts Keep belts clean and dry . { W ARNING: Do not bleach o[...]

Rinse the vehicle well, before washing and after to remove all cleaning agents completely . If they are allowed to dry on the surface, they could stain. Dry the finish with a soft, clean chamois or an all-cotton towel to avoid surface scratches and water spotting. High pressure car washes may cause water to enter the vehicle. Avoid using high press[...]

If necessary , use non-abrasive cleaners that are marked safe for painted surfaces to remove foreign matter . Exterior painted surfaces are subject to aging, weather and chemical fallout that can take their toll over a period of years. T o help keep the paint finish looking new , keep the vehicle garaged or covered whenever possible. Protecting Ext[...]

Aluminum or Chrome-Plated Wheels and T rim The vehicle may have either aluminum or chrome-plated wheels. Keep the wheels clean using a soft clean cloth with mild soap and water . Rinse with clean water . After rinsing thoroughly , dry with a soft clean towel. A wax may then be applied. Notice: Chrome wheels and other chrome trim may be damaged if t[...]

Tires T o clean the tires, use a stiff brush with tire cleaner . Notice: Using petroleum-based tire dressing products on the vehicle may damage the paint finish and/or tires. When applying a tire dressing, always wipe off any overspray from all painted surfaces on the vehicle. Sheet Metal Damage If the vehicle is damaged and requires sheet metal re[...]

V ehicle Identification V ehicle Identification Number (VIN) This legal identifier is in the front corner of the instrument panel, on the driver side. It can be seen through the windshield from outside. The VIN also appears on the V ehicle Certification and Service Parts labels and certificates of title and registration. Engine Identification The e[...]

The vehicle has an airbag system. Before attempting to add anything electrical to the vehicle, see Servicing Y our Airbag-Equipped Vehicle on page 2 ‑ 66 and Adding Equipment to Y our Airbag-Equipped Vehicle on page 2 ‑ 66 . Headlamp Wiring The headlamp wiring is protected by fuses in the fuse block. An electrical overload will cause the lamps [...]

Underhood Fuse Block 6-1 18[...]

The underhood fuse block is located in the front of the engine compartment on the passenger side of the vehicle. See Engine Compartment Overview on page 6 ‑ 13 for more information on location and removal procedure for the front compartment underhood sights shields. T o access the fuses, push in the tabs located on each side of the fuse block cov[...]

Fuses Mini Usage EKM/I/P MDL Easy Key Module (EKM), Instrument Panel Module (I/P MDL) EVEN COILS Even Ignition Coils, Even Fuel Injectors FOG LAMP Front Fog Lamps FRT PWR OUTLET Front Accessory Power Outlet FUEL COOL Fuel Cooling HORN Horn HTD W ASH/AQS Heated Headlamp W asher , Air Quality Sensor HUD Heads-Up Display , Steering Column Switch I/BEA[...]

Fuses Mini Usage V/CHK Instrument Panel Module-V oltage Check WPR Wipe/W ash Module Assembly WPR SW/VICS Rain Sensor , Wiper Switch Relays Usage A/C CMPRSR CL TCH Air Conditioning Compressor Clutch ACCY Accessory , Rain Sensor , Headlamp W asher Relay Coil, Windshield Wiper/W asher Module BRK V AC PUMP Brake V acuum Pump F AN S/P Cooling Fan Series[...]

Rear Underseat Fuse Block Removing the Rear Seat Cushion Notice: If you touch the exposed wires with the metal on the seat cushion, you could cause a short that could damage the battery and or wires. Avoid contact between the rear seat and the fuse center whenever you remove or reinstall the rear seat. Do not remove covers from any of the covered p[...]

{ W ARNING: A safety belt that is not properly routed through the seat cushion or is twisted will not provide the protection needed in a crash. If the safety belt has not been routed through the seat cushion at all, it will not be there to work for the next passenger . The person sitting in that position could be badly injured. After reinstalling t[...]

The vehicle may not have all the fuses listed below . Driver's Side 6-124[...]

Fuses Usage AMP Amplifier SP ARE Spare THEFT/SHFT Theft Sensors, Auto Shifter , Power Sounder MRTD MDL Magnetic Ride Control Module (Option) REAR DR MDL Rear Door Modules ELC EXH Electronic Level Control, Exhaust Solenoid (Option) DDM Driver Door Module, Front Door SubWoofers (Option) TV/VICS/SCM Infotainment (Export Only), Supervisory Control Modu[...]

Relays Usage SP ARE Spare ELC CMPRSR Electronic Level Control, Compressor (Option) L T POS Left Rear T aillamp, Position Lamps (Option) RT POS Right Rear T aillamp, Position Lamps (Option) RUN Ignition 3 STDBY LAMP Rear T aillamps, Position Lamps (Option) TRUNK RELSE T runk Release Motor BCK/UP LAMP Reverse Lamps, Rear Parking Aid, Inside Rearview [...]

Passenger's Side 6-127[...]

Fuses Usage AIRBAG/IGN Sensing and Diagnostic Monitor , Automatic Occupant Sensor , Passenger Supplemental Inflatable Restraint CNSTR/VENT Canister V ent Solenoid SP ARE Spare FRT PDM Front Passenger Door Module, Right Power Subwoofer FUEL PUMP Fuel Pump HTD STR Heated Steering Wheel RF HTD/ SEA T/XM Front Passenger Heated Seat, S-Band ™ Antenna [...]

Relays Usage SP ARE Spare FUEL PUMP Fuel Pump INT LAMP Interior Lamps REAR DEFOG Rear Defogger REAR/FOG Rear Fog Lamps (Option) RUN/CRNK Ignition 1 SP ARE Spare STOP LAMP Stop Lamp Circuit Breakers Usage WINDOW MTRS Power Window Motors Circuit Breaker Diodes Usage TRUNK DIODE Trunk Release Joint Connector Usage J/C Splice Pack (Blue) 6-129[...]

Capacities and Specifications The following approximate capacities are given in English and metric conversions. See Recommended Fluids and Lubricants on page 7 ‑ 9 for more information. Application Capacities Metric English Air Conditioning Refrigerant R134a For the air conditioning system refrigerant charge amount, see the refrigerant caution la[...]

Application Capacities Metric English T ransmission Fluid (Pan Removal and Filter Replacement) 6-Speed Automatic 6.3 L 6.7 qt Wheel Nut T orque 140 Y 100 lb ft All capacities are approximate. When adding, be sure to fill to the approximate level as recommended in this manual. Recheck the fluid level after filling. Engine Specifications Engine VIN C[...]

2 NOTES 6-132[...]

Section 7 Maintenance Schedule Maintenance Schedule ........................ .... 7-2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2 Scheduled Maintenance . . . . . . . . . . . . . . . . . . . . . . . . 7-3 Owner Checks and Services . . . . . . . . . . . . . . . . . . . . 7-7 Recommended Fluids and Lubric[...]

Maintenance Schedule Introduction Notice: Maintenance intervals, checks, inspections, recommended fluids, and lubricants are necessary to keep this vehicle in good working condition. Damage caused by failure to follow scheduled maintenance might not be covered by the vehicle warranty . Proper vehicle maintenance helps to keep the vehicle in good wo[...]

At your General Motors dealer/retailer , you can be certain that you will receive the highest level of service available. Y our dealer /retailer has specially trained service technicians, uses genuine GM replacement parts, as well as, up to date tools and equipment to ensure fast and accurate diagnostics. The proper replacement parts, fluids, and l[...]

Every Engine Oil Change . Change engine oil and filter . See Engine Oil on page 6 ‑ 18 . An Emission Control Service. . Engine coolant level check. See Engine Coolant on page 6 ‑ 27 . . Windshield washer fluid level check. See Windshield Washer Fluid on page 6 ‑ 36 . . T ire inflation check. See Inflation - Tire Pressure on page 6 ‑ 60 . . [...]

Additional Required Services At Each Fuel Stop . Engine oil level check. See Engine Oil on page 6 ‑ 18 . . Engine coolant level check. See Engine Coolant on page 6 ‑ 27 . . Windshield washer fluid level check. See Windshield Washer Fluid on page 6 ‑ 36 . Once a Month . Tire inflation check. See Inflation - Tire Pressure on page 6 ‑ 60 . . T[...]

First Engine Oil Change After Every 64 000 km/40,000 Miles . 3.6L (Code V) V6 Engine Only: Engine air cleaner filter replacement. See Engine Air Cleaner/Filter on page 6 ‑ 23 . First Engine Oil Change After Every 80 000 km/50,000 Miles . 4.6L (Code A) V8 Engine Only: Engine air cleaner filter replacement. See Engine Air Cleaner/Filter on page 6 ?[...]

Owner Checks and Services Starter Switch Check { W ARNING: When you are doing this inspection, the vehicle could move suddenly . If the vehicle moves, you or others could be injured. 1. Before starting this check, be sure there is enough room around the vehicle. 2. Firmly apply both the parking brake and the regular brake. See Parking Brake on page[...]

Parking Brake and Automatic T ransmission P (Park) Mechanism Check { W ARNING: When you are doing this check, the vehicle could begin to move. Y ou or others could be injured and property could be damaged. Make sure there is room in front of the vehicle in case it begins to roll. Be ready to apply the regular brake at once should the vehicle begin [...]

Recommended Fluids and Lubricants Fluids and lubricants identified below by name, part number , or specification can be obtained from your dealer/retailer . Usage Fluid/Lubricant Engine Oil The engine requires a special engine oil meeting GM Standard GM4718M. Oils meeting this standard can be identified as synthetic, and should also be identified w[...]

Usage Fluid/Lubricant Key Lock Cylinders Multi-Purpose Lubricant, Superlube (GM Part No. U.S. 12346241, in Canada 10953474). Rear Axle SAE 75W-90 Synthetic Axle Lubricant (GM Part No. U.S. 89021677, in Canada 89021678) meeting GM Specification 99861 15. Front Axle (All-Wheel Drive) SAE 75W-90 Synthetic Axle Lubricant (GM Part No. U.S. 89021677, in [...]

Maintenance Replacement Parts Replacement parts identified below by name, part number , or specification can be obtained from your dealer/retailer . Part GM Part Number ACDelco Part Number Engine Air Cleaner/Filter Element 3.6L and 4.6L Engines 25798271 A2944C Engine Oil Filter 3.6L Engines 25177917 PF2129 4.6L Engine 89017342 PF61 Passenger Compar[...]

Engine Drive Belt Routing 3.6L V6 Engine 4.6L V8 Engine 7-12[...]

Maintenance Record After the scheduled services are performed, record the date, odometer reading, who performed the service, and the type of services performed in the boxes provided. Retain all maintenance receipts. Maintenance Record Date Odometer Reading Serviced By Maintenance Stamp Services Performed 7-13[...]

Maintenance Record (cont'd) Date Odometer Reading Serviced By Maintenance Stamp Services Performed 7-14[...]

Maintenance Record (cont'd) Date Odometer Reading Serviced By Maintenance Stamp Services Performed 7-15[...]

Maintenance Record (cont'd) Date Odometer Reading Serviced By Maintenance Stamp Services Performed 7-16[...]

Section 8 Customer Assistance Information Customer Assistance and Information . . . . . . . . . . . 8-2 Customer Satisfaction Procedure . . . . . . . . . . . . . . . 8-2 Online Owner Center . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5 Customer Assistance for T ext T elephone (TTY) U s e r s ................. ............ ............[...]

Customer Assistance and Information Customer Satisfaction Procedure Y our satisfaction and goodwill are important to your dealer and to Cadillac. Normally , any concerns with the sales transaction or the operation of the vehicle will be resolved by the dealer's sales or service departments. Sometimes, however , despite the best intentions of a[...]

STEP THREE (U.S. Owners) : Both General Motors and your dealer are committed to making sure you are completely satisfied with your new vehicle. However , if you continue to remain unsatisfied after following the procedure outlined in Steps One and T wo, you can file with the Better Business Bureau (BBB) Auto Line Program to enforce your rights. The[...]

STEP THREE (Canadian Owners): General Motors Participation in the Mediation/ Arbitration Program In the event that you do not feel your concerns have been addressed after the following the procedure outlined in Steps One and T wo. General Motors of Canada Limited wants you to be aware of its participation in a no-charge mediation/Arbitration progra[...]

Online Owner Center Online Owner Center (U.S.) — www .gmownercenter .com/cadillac Information and services customized for your specific vehicle — all in one convenient place. . Digital owner manual, warranty information, and more . Online service and maintenance records . Find Cadillac dealers for service nationwide . Exclusive privileges and o[...]

Customer Assistance for T ext T elephone (TTY) Users T o assist customers who are deaf, hard of hearing, or speech-impaired and who use T ext T elephones (TTYs), Cadillac has TTY equipment available at its Customer Assistance Center . Any TTY user can communicate with Cadillac by dialing: 1-800-833-CMCC (2622). (TTY users in Canada can dial 1-800-2[...]

Overseas — Customer Assistance Please contact the local General Motors Business Unit. Mexico, Central America and Caribbean Islands/Countries (Except Puerto Rico and U.S. Virgin Islands) — Customer Assistance General Motors de Mexico, S. de R.L. de C.V . Customer Assistance Center Paseo de la Reforma # 2740 Col. Lomas de Bezares C.P . 1 1910, M[...]

Roadside Service In the United States or Canada, call 1-800-882-1 112 . T ext T elephone (TTY), U.S. only , call 1-888-889-2438 . Service is available 24 hours a day , 365 days a year. Calling for Assistance When calling Roadside Assistance, have the following information ready: . Y our name, home address, and home telephone number . T elephone num[...]

. Emergency T ow From a Public Road or Highway: T ow to the nearest Cadillac dealer for warranty service, or if the vehicle was in a crash and cannot be driven. Assistance is also given when the vehicle is stuck in the sand, mud, or snow . . Flat Tire Change: Service is provided to change a flat tire with spare tire. The spare tire, if equipped, mu[...]

Services Specific to Canadian Purchased V ehicles . Fuel delivery: Reimbursement is approximately $5 Canadian. Diesel fuel delivery may be restricted. Propane and other fuels are not provided through this service. . Lock-Out Service: V ehicle registration is required. . T rip Routing Service: Limit of six requests per year . . T rip Interruption Be[...]

Courtesy Transportation is not a part of the New V ehicle Limited W arranty . A separate booklet entitled “ Warranty and Owner Assistance Information ” furnished with each new vehicle provides detailed warranty coverage information. T ransportation Options W arranty service can generally be completed while you wait. However , if you are unable [...]

Additional Program Information All program options, such as shuttle service, may not be available at every dealer . Please contact your dealer for specific information about availability . All Courtesy T ransportation arrangements will be administered by appropriate dealer personnel. General Motors reserves the right to unilaterally modify , change[...]

Repair Facility GM also recommends that you choose a collision repair facility that meets your needs before you ever need collision repairs. Y our GM dealer/retailer may have a collision repair center with GM-trained technicians and state of the art equipment, or be able to recommend a collision repair center that has GM-trained technicians and com[...]

Choose a reputable repair facility that uses quality replacement parts. See “ Collision Parts ” earlier in this section. If the airbag has inflated, see What Will Y ou See After an Airbag Inflates? on page 2 ‑ 59 . Managing the V ehicle Damage Repair Process In the event that your vehicle requires damage repairs, GM recommends that you take a[...]

T o contact NHTSA, you may call the V ehicle Safety Hotline toll-free at 1-888-327-4236 (TTY : 1-800-424- 9153); go to http://www .safercar.gov ; or write to: Administrator , NHTSA 1200 New Jersey Avenue, S.E. W ashington, D.C. 20590 Y ou can also obtain other information about motor vehicle safety from http://www .safercar .gov . Reporting Safety [...]

Service Publications Ordering Information Service Manuals Service Manuals have the diagnosis and repair information on engines, transmission, axle suspension, brakes, electrical, steering, body , etc. Service Bulletins Service Bulletins give additional technical service information needed to knowledgeably service General Motors cars and trucks. Eac[...]

V ehicle Data Recording and Privacy Y our GM vehicle has a number of sophisticated computers that record information about the vehicle ’ s performance and how it is driven. For example, your vehicle uses computer modules to monitor and control engine and transmission performance, to monitor the conditions for airbag deployment and deploy airbags [...]

GM will not access this data or share it with others except: with the consent of the vehicle owner or , if the vehicle is leased, with the consent of the lessee; in response to an official request of police or similar government office; as part of GM's defense of litigation through the discovery process; or , as required by law . Data that GM [...]

A Accessories and Modifications . . . . . . . . . . . . . . . . . . . . . . .6-4 Accessory Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-26 Accessory Power Outlets . . . . . . . . . . . . . . . . . . . . . . . . . . 4-42 Adaptive Cruise Control . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-15 Add-On Electrica[...]

Audio System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-94 Audio Steering Wheel Controls . . . . . . . . . . . . . . . . . . 4-134 Navigation/Radio System, see Navigation Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 13 Radio Personalization . . . . . . . . . . . . . [...]

Carbon Monoxide Engine Exhaust . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-36 T runk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15 Winter Driving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-20 Care of Safety Belts . . . . . . . . . . . . . . .[...]

Convenience Net . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-56 Coolant Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-27 Engine T emperature Gage . . . . . . . . . . . . . . . . . . . . . . . . 4-61 Engine T emperature Warning Light . . . . . . . . . . . . . . . 4-61 Coolin[...]

E EDR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-17 Electrical Equipment, Add-On . . . . . . . . . . . . . . . . . . . . 6-1 16 Electrical System Fuses and Circuit Breakers . . . . . . . . . . . . . . . . . . . . . . 6-1 17 Headlamp Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[...]

Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-6 Additives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8 California Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7 Filling a Portable Fuel Container . . . . . . . . . [...]

Heater Engine Coolant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-29 High-Speed Operation, T ires . . . . . . . . . . . . . . . . . . . . . . 6-62 Highbeam On Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-68 Highway Hypnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-18 [...]

Lights (cont.) Engine Coolant T emperature Warning . . . . . . . . . . . . 4-61 Flash-to-Pass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9 Fog Lamps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-67 High/Low Beam Changer . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5 Highb[...]

N Navigation System, Privacy . . . . . . . . . . . . . . . . . . . . . . . . 8-18 Navigation/Radio System, see Navigation Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 13 Net, Convenience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-56 New V ehicle Break-In . . . . . . . . . . [...]

Phone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-123 Bluetooth ® ............ ............ ............. .. 4 - 1 1 3 Power Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13 Electrical System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-[...]

Replacement Parts Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1 1 Reporting Safety Defects Canadian Government . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-15 General Motors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-15 U.S. Government . . . . . . . . . . . . . [...]

Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4 Accessories and Modifications . . . . . . . . . . . . . . . . . . . . . 6-4 Adding Equipment to the Outside of the V ehicle . . . 6-6 Doing Y our Own Work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5 Engine Soon Lamp . . . . . . [...]

T ires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-52 Aluminum or Chrome-Plated Wheels, Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1 14 Buying New T ires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-70 Chains . . . . . . . . . . [...]

V V alet Lockout Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-24 V ehicle Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3 Loading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-23 Personalization . . . . . . . . . . . . . . . . . . .[...]