Caliber MCD 165 Bedienungsanleitung

INSTR UCTION MANU AL C AR CD/MP3 PLA YER / RDS RECEIVER MCD 165[...]

BAND 1 2 3 4 5 6 DISP This unit is equipped with the most advanced “TOUCH SENSE P ANEL ” which is easy and convenient to use. And here is some tips on how to use this touch sense panel: Tips The pressing or activating of each button actually all you need is a very light touch, even not really necessary to “PRES S” it. Just touch lightly can[...]

E - 2 1. HANDLING COMP ACT DISCS MOISTURE CONDENSA TION NOTES ON CDs P . 2 P . 3 P . 4 P . 1 P . 5 P . 6 P . 7 1. 2. 3. 4. 5. NOTES ON DISCS There are paste residue. Ink is sticky (P .5). Stickers that are beginning to peel away , leaving a sticky residue (P .6). Labels are attached (P .7). On a rainy day or in a very damp area, moisture may conden[...]

2. INST ALLA TION Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and system work properly . Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions. Consult with your nearest dealer if installation req[...]

DIN REAR-MOUNT (METHOD B) Installation using the screw holes on the sides of the unit. Fastening the unit to the factory radio mounting bracket. 1. Select a position where the screw holes of the bracket and the screw holes of the main unit become aligned (are fitted) and tighten the screws at 2 places on each side. 2. Screw 3. Factory radio mountin[...]

3. DET ACHABLE CONTROL P ANEL (D .C.P .) Removing The Detachable Control Panel (D.C.P .). 1. T urn the power off 2. Press the D .C.P . release button 3. Remove the D .C.P . P ANEL RELEASE BUTTON B A 2 Attaching the DCP CAUTION 1. Attach the panel at the right side first, with point B on the main unit touching point A on the D .C.P . (As shown on th[...]

4. WIRING DIAGRAM AMP CONNECTOR ISO FEMALE WITH MALE TERMINAL ISO CONNECTOR 4 PIN+8 PIN 1 1 2 3 7 5 7 5 3 8 6 4 2 4 6 8 (See Figure 1) Figure 1 ISO CONNECTOR WIRING CHART GROUND POWER ANTENNA BATTERY(+) IGNITION(ACC) RIGHT REAR SPEAKER (-) RIGHT FRONT SPEAKER (-) LEFT FRONT SPEAKER (+) RIGHT FRONT SPEAKER (+) RIGHT REAR SPEAKER (+) LEFT REAR SPEAKE[...]

Press this button to remove the control panel. 5. BASIC OPERA TIONS 1) P ANEL RELEASE BUT TON (REL) 11) DISP BUTTON(DISP) 13) POWER ON/OFF BUTTON ( ) Press the POWER button on the front of the unit to turn on the unit. Long press the POWER button to turn Off the unit. 13) MUTE BUTTON (MUTE) Short Press the MUTE button to mute the audio output, and [...]

6. MENU OPERA TIONS TIME SET (CLK) The time on the clock is set to “12:00” by default, Rotate the encoder volume knob to adjust the minutes and hours.Press AUDIO/MENU button to select the hour or minutes. Note: Time format can not to set up, it should be follow the tunner area to change, when is in U .S.A Latin then the time in 12H by default, [...]

7. RADIO OPERA TIONS 9) RADIO SIGNAL STRENGTH METER (RSLM) This is use to indicate the signal strength of current radio station broadcast. When you choose RADIO mode, it will show on the display . 7) ST ATION PRESET BUTTONS (M1-M6) 1.Press these buttons briefly to recall the stored stations in the selected band. 2.Presetting stations manually , Pre[...]

17)T A BUT TON When pressed short, it is activated as T A mode on or off When T A mode is on and traffic announcement is transmittude - When the unit is in CD mode, it will switch to radio mode temporarily . - If the volume lever was under the threshold point, it will be raised to the threshold point. - When TP station is received, TP segment is tu[...]

OVERVIEW OF THE RDS FUNCTION Radio Data System (RDS) is a broadcasting service that allows FM stations to send additional digital information along with the regular radio program signal. Y our car stereo offers you a variety of services. Here are just a few: - PI (Program identification) It is a code that identified RDS stations; it is unique for e[...]

PROGRAMMABLE OPTIONALS - T A SEEK , T A ALARM T o determine what action will the radio take if the newly tuned station does not receive TP information for 5 seconds. T A SEEK The radio retunes to a different station which contains TP information. T A ALARM The radio does not retune but beeps will come out. - PI SOUND, PI MUTE When the vehicle is cr[...]

9.CD OPERA TIONS 4) CD SL OT Insert the disc into CD slot. The CD will begin to play . M1) P AUSE BUTTON (P AU) Press this button to pause CD play , press again to release pause. M2) INTROL BUTTON (INT) Press this button, the first 10 seconds of each track will be played sequentially until this button is pressed again, then normal play will resume [...]

Notes : L OADING DISC NAVIGA TING THROUGH DIRECTORIES AND TRACKS Insert the CD as usual, if it is an MP3 CD , the display will show “MP3 T01” then the message “READING” will appear , when disc scanning completed, the first track on the first directory will play . - An MP3 directory is shown in this manual as “Directory”, and an MP3 file[...]

(2) SEARCH DIRECTORY / TRACK NAME B Y USING ENCODER VOLUME KNOB Under MP3 Play Mode, press MP3 MENU BUTTON twice, the display shows “ * “. Rotate the ENCODER VOLUME KNOB for selecting the character . In this Encoder Search mode, SELECT button use as move cursor . Press BAND/L OUDNES S button use as MP3 CONFIRM BUTTON. The unit searches files an[...]

GENERAL AM/MW Power Supply Polarity Speaker impedance Power Output Frequency Range Intermediate Frequency Usable Sensitivity Stereo Separation S/N Ratio DC 11 -14V Negative Ground 4 ohms 7 5W x 4 87.5-108 Mhz 10.7 MHz Better than 15dB at S/N 30 dB 25 dB at 1KHz 50 dB 11.SPECIFICA TIONS CD PLA YER REMARK : Specifications subject to change without no[...]

12.TROUBLE SHOOTING Before going through the check list, check wiring connection. If any of the problems persist after check list has been made, consult your nearest service dealer . Symptom Cause Solution No power The car ignition is not on. If the power supply is properly connected to the car accessory terminal, switch the ignition key to “ ACC[...]