Canon IMAGECLASS MF7400 Bedienungsanleitung

ENG Star ter Guide Please read this guide befor e operating this pr oduct. After you nish r eading this guide, st ore it in a safe plac e for futur e ref erence .[...]

1 Set Up the Machine Unpacking the Machine Remove all shipping tape and packing material from the machine . Remove the vin yl-tie and label attached on the metal plate in each paper cassette .[...]

2 Before Setting Up the Machine When carr ying the machine, be sure tha t it is carried by two or more people holding the parts indicated below . The shapes of your machine and supplies ma y dier slightly fr om those illustrations listed in this manual. ● ●[...]

3 Do Y ou Hav e Ev er ything? Machine ● Cartridge ● Po wer Cor d ● T elephone Cable ● F errite Core f or USB Cable ● Document Size Label ● Starter Guide ● Limited W arranty Notice ● Paper Siz e Label ● Basic Operation Guide ● Cartridge W arranty Notice ● Stamp Cartridge ● UFRII L T/F AX User Software CD-ROM ● Registration [...]

4 Manuals for the Machine Starter Guide ( This Document): Machine set-up and software installation Basic Operation Guide: Basic fea tures, main tenance, tr ouble shooting, and specications Referenc e Guide (located on the Manual CD-ROM): T otal operation f eatures , network and remote user interface, system settings , reports and lists, and trou[...]

5 Install Car tridge 1 Remove the cartridge from the bag. 2 Remove the desiccant bag and the shipping tape . 3 Remove the short shipping tape. 4 Remove the packing materials. 5 Gently rock the cartridge several times to evenly distributed the toner inside. 6 Place the cartridge on a at sur face and pull the seal completely out. Do not pull out t[...]

6 7 Remove the long shipping tape . 8 Remove the prot ective cover . 9 Push the release butt on on the left cover of the main unit to open the left cover . 10 Open the front co ver . 11 Rotate the unlock lever until it clicks . 12 While grasping the handle of the cartridge holder , pull the cartr idge holder out of the machine until it stops.[...]

7 13 Hold the cartr idge by its handle, then insert it into the cartr idge holder . 14 Push the cartridge holder into the machine as far as it will go. 15 Rotate the lever to the locked position. 16 Close the front co ver . Be careful not to get your ngers caught . 17 Gently close the left cover until it clicks . Be careful not to get your ng[...]

8 Load P ap er 1 Pull out the paper dra wer until it stops . 2 Push down the metal pla te to lock. If you load L TR size paper , go to step 6, or otherwise go to step 3. 3 Detach the end guide (A) by pr essing it down. Reattach the end guide into the desired paper siz e slots and tilt it backwards to its original upright position. 4 Lift the lock l[...]

9 6 F an the paper stack and ev en the edges. 7 Load the paper stack of the appropriate size with the print side facing up. When loading paper , be careful not to cut your ngers at the edges of the paper . Make sure the paper stack does not exc eed the load limit mark (A) and it is loaded under the small ns (B) on the paper guides. Each paper[...]

10 9 Pull out the paper size pla te (A) fr om the paper draw er . 10 Stick the appropriate paper siz e label on the paper size plate. 11 Reinser t the paper size plate int o the paper drawer . 12 Push the paper dra wer into the machine as far as it will go. Be careful not to get your ngers caught . F or loading paper in the stack bypass, see Cha[...]

11 Ax Labels Ax the supplied document size label t o the specied location. 1 Align the slide guide (A ) to the original size mark “ A4/A3” (B). 2 Ax the document size label ( A) to the f eeder cover so that both indica tors (B and C) on the side guide and the document size label are aligned pr operly , as shown on the right.[...]

12 C onnect the Po w er C ord and T urn On the Machine 1 Connect the supplied power cor d (A) in t o the socket and the wall outlet. 2 Pr ess the main power switch t o “I” side. The Start Up screen is displayed until the machine comes to the ready mode . The Basic F eatures scr een is displayed when the machine is ready to scan. <Close the l[...]

13 C onnect T elephone Cables B A Connect the supplied telephone cable (A) t o the line jack (B) on the back side of the machine and the wall jack. Set the Date and T ime Before using the machine , you MUST set the curren t date and time. The current date and time settings ar e used as standard timer settings f or functions that require them. Use t[...]

14 1 Pr ess (A dditional F unctions). 2 Pr ess [ T imer Settings]. 3 Pr ess [Date & Time Settings]. 4 Use - (Numeric Keys) to enter the date (month/day/year) and time (in 24-hour/military time format), then pr ess [OK]. Enter the month and the day using f our digits (including zeros). Enter all four dig its of the year , and the time in 24-hour[...]

15 6 Select the time zone in which the machine is located, then pr ess [OK]. The standard time zones of the w orld are expressed globally in terms of the dierenc e in hours (up to 12 hours) from GMT (0 hours). A time zone is a r egion throughout which this time dier ence is the same. The time at the Green wich Observator y in England is calle[...]

16 9 Select the month and day from the Month and Day drop-down lists, then press [ OK ]. 10 Pr ess [End Date]. 11 Select the month and day at which Daylight Saving Time ends then press [OK]. 12 Pr ess [OK]. 13 Pr ess [OK]. The selected mode is set. 14 Pr ess [Done] repeatedly until the Send Basic F eatures scr een appears.[...]

17 Set the T elephone Line T ype 1 Pr ess (A dditional F unctions). 2 Pr ess [Communica tions Settings]. 3 Pr ess [User Settings] under <F ax S ettings>. 4 Pr ess [ T el Line T ype]. 5 Select the telephone line type, then press [OK]. <T one>: T one dialing <Pulse>: P ulse dialing If you do not know the type of telephone line you u[...]

18 Set the Machine for Sending Doc uments Guidelines for Ent ering Informa tion Before sending documen ts, you MUST r egister your fax number , and user name (unit name) in the machine. The sender information y ou regist er in the machine appears in the header of each page receiv ed by your r ecipient. Date 06/30/2007 F AX (404)XXX-XXXX CANON SALES[...]

19 Register Sender Information Y ou must stor e your machine ’ s fax number . This number is print ed on the top of every document you send to the recipient. Y our machine ’ s telephone number ma y also be displayed on the t ouch panel display of the recipient’ s machine, depending on their type of machine. 1 Pr ess (A dditional F unctions). [...]

20 6 Pr ess [Done]. 7 Pr ess [ TX Settings] under <Common Settings>. 8 Pr ess [Unit Name]. Enter your name or c ompany name (and department name if possible) as the unit name. When you send a document, the r ecipient’ s machine will print this unit name as the sender information on the recording paper . Some fax models also display sender i[...]

21 Set the Machine for Netw or k U sage (imageCLASS MF7480/MF7470 O nly) C onnect the M achine to a Netw ork This machine has a USB connector and LAN connector . If the machine is connec ted to a network using a LAN cable, you can print the documen ts sent from a comput er . The imageCLASS MF7480 can also send documents as e -mail attachments, send[...]

22 Specify the IP Addr ess Settings An IP address must be specied in or der to enable communication between the machine and comput er . It is recommended that the network administrator perform the following proc edures. Before performing the following pr ocedure, make sur e that the machine is turned on and connected to a network. This machine i[...]

23 6 Pr ess [IP Address Settings]. 7 Pr ess [IP Address], then en ter the IP address using - (Numeric Keys). If you specify an IP address using DHCP , BOO TP , or R ARP , press [DHCP], [BOO TP], or [RARP]. One of the DHCP , BOO TP , or RARP settings can be selected at any one time. 8 Pr ess [Subnet Mask] and [Gateway A ddress] and specify the setti[...]

24 Installing Sof twar e P er form the following pr ocedure t o install the printer and fax drivers. If you install these driv ers, you can print and fax from your c omputer . Printer drivers ar e divided into two types: PCL and UFRII L T . PCL: This is the Hewlett -P ackard’ s PCL printer driver , which includes the PCL5c, PCL5e, and PCL6 driver[...]

25 Installation P rocedur e f or USB C onnec tion 1 Inser t the UFRII L T/F A X User Software CD-ROM. 2 If the CD-R OM Setup screen is not displayed , click [star t] on the Windo ws task bar → [My Computer]. Window s Vista: click [start] on the Window s task bar → [Comput er]. Window s 98/Me/2000: double - click [My Computer] on the W indows de[...]

26 10 11 Attach the ferrite c ore (A ) as close as possible to the B-type side (square) of the USB cable (B). 12 Connect the machine and your computer with a USB cable (A ). If you are using W indows XP , [F ound New Hardware Wizard] dialog box appears . Select [I nstall Software Automatically (Recommended)] then click [Next]. 13 14 15 16 17 A [Pr [...]

27 19 20 Select the USB por t you want to use from [P ort]. I f you want to add a port, click [AddP or t] and then selec t the USB port you want to add. 21 22 23 24 25 The Color Network ScanGear installation screen appears . F ollow the on-screen instructions. If you are using MF7460, skip the Color Network ScanGear installation. 26 27[...]

28 28 Remove the UFRII L T/F AX User Soft ware CD-ROM. If you are using MF7460, you ha ve now completed installation. 29 Inser t the PCL User Soft ware CD-ROM. (MF7480/MF7470 Only) 30 If the CD-R OM Setup screen is not displayed , click [star t] on the Windo ws task bar → [My Computer]. Window s Vista: click [start] on the Window s task bar → [[...]

29 36 Select [Canon MF7400 Series PCL5e] or [Canon MF7400 Series PCL6] . 37 38 Select the USB por t you want to use from [P ort]. I f you want to add a port, click [Add P or t] and then selec t the printer port you want to add. 39 40 41 42 43 44 45 Remove the PCL User Software CD- ROM. Y ou have now completed installation.[...]

30 1 Connect the machine to the network correctly , and conrm that the pow er is on. 2 Inser t the UFRII L T/F A X User Software CD-ROM. 3 If the CD-R OM Setup screen is not displayed , click [star t] on the Windo ws task bar → [My Computer]. Window s Vista: click [start] on the Window s task bar → [Comput er]. Window s 98/Me/2000: doublecli[...]

31 10 11 12 13 14 15 16 17 18 19 A [Pr ocess to Install F ax Driver] dialog box will appear if drivers that can be installed with this Installer are already installed. Select the desired installation and then click [Next].[...]

32 20 21 22 23 24 25 The Color Network ScanGear installation screen appears. F ollow the on-screen instructions. 26 27 28 Remove the UFRII L T/F AX User Soft ware CD-ROM. 29 Inser t the PCL User Soft ware CD-ROM.[...]

33 30 If the CD-R OM Setup screen is not displayed , click [star t] on the Windo ws task bar → [My Computer]. Window s Vista: click [start] on the Window s task bar → [Comput er]. Window s 98/Me/2000: double - click [My Computer] on the W indows desktop . Open the CD-ROM icon, then double - click [MInst] ([MInst.exe]). 31 Select the PCL Printer[...]

34 39 40 41 42 43 44 45 Remove the PCL User Software CD- ROM. Y ou have now completed installation.[...]

35 Checking the Installation Check if the drivers are installed succ essfully and that the machine is selected as the default printer . If your machine is selected in the [Printer] area when y ou open the [Print] dialog bo x from an application, your machine is set as the default printer . 1 Open the [Printers and F axes] f older ( W indows 98/2000[...]

36 Manual CD -ROM Menu S y stem Requiremen ts The Manual CD-ROM Menu can be used in the following system en vironments. Operation Sy stem Microsoft W indows 98/98SE Microsoft W indows Me Microsoft W indows 2000 Pr ofessional/Server(Ser vice Pack 4 or la ter) Microsoft W indows XP (Service Pack 1a or later) Microsoft W indows Server 2003 Microsoft W[...]

37 Using the CD-ROM Menu This section describes how to use the CD-ROM Menu. When you insert the User Manual CD -ROM provided int o the CD-ROM dr ive , the Language Selec tion screen is displayed . Clicking on this screen display s the following menu . Click [Referenc e Guide] to read the Ref erence Guide . After clicking on the guide, Acrobat Reade[...]

38 T rademarks Canon, the Canon logo and imageCLASS ar e trademarks of Canon Inc. Microsoft, Window s, Windows Server and Window s V ista are trademarks or reg istered trademarks of Microsoft Corporation in the U .S. and/or other countries. Adobe and A dobe Acroba t are trademarks of Adobe S ystems Incorporated . Mac OS is a register ed trademark o[...]

CANON INC. 30-2, Shimomaruko 3-chome, Ohta-ku, T okyo 146-8501, Japan CANON U.S.A., INC. One Canon Plaza, Lake Success , NY 11042, U .S.A. CANON CANADA INC. 6390 Dixie Road Mississauga, Ontario L5T 1P7, Canada CANON EUROP A N.V . Bovenkerkerweg 59-61 1185 XB Amstelveen, The Netherlands CANON FRANCE S.A.S. 17, quai du Présiden t Paul Doumer 92414 C[...]