Canon MARK IV Bedienungsanleitung

E INSTRUCTION MANUAL E INSTRUCTION MANUAL C OP Y[...]

2 Thank you for purchasing a Canon product. The EOS-1D Mark IV is a top- of-the-line, high-performance EOS DIGIT AL SLR camera featuring a large, fine-detail CMOS sensor with approx. 16.10 effective megapixels, D ual “DIGIC 4”, high-precision and high-speed 45-point AF (39 cro ss-type points), approx. 10 fp s continuous shooting, Live View shoo[...]

3 Before starting, check that all t he following items have been included with your camera. If anything is missing, contact your dealer . * Be careful not to lose any of the above items. Item Check List Battery Pack LP-E4 (with protective cover) Battery Charger LC-E4 Interface Cable IFC-200U Stereo A V Cable A VC-DC400ST EOS DIGIT AL Solution Disk [...]

4 Icons in this Manual < 6 > : Indicates the Main Dial. < 5 > : Indicates the Quick Control Dial. < 9 > : Indicates the Multi-controller . < 0 > : Indicates the setting button. 9 , 8 : Indicates that the respective function remains active for 6 sec. or 16 sec. respectively after you let go of the button. * In this manual, th[...]

5 Chapters Introduction Camera basics. 2 Getting St arted 27 Image Settings Image-recording quality , ISO speed, Picture Style, etc. 55 Setting the AF and Drive Modes Setting the AF mode, AF point, and drive mode. 93 Exposure Control Metering mode, shooting mode , flash, and other settings. 103 Live View shooting Shoot photos while vi ewing the LCD[...]

6 2 1 Introduction Item Check List ....................... ........................................................................... 3 Conventions Used in this Manual ............................................... ....................... 4 Chapters .......................................................................................... .......[...]

7 Contents 4 3 A Registering a Picture St yle ........................................... ............................70 Setting the White Balanc e .................................................... ............................ 72 O Custom White Balance ........................................ ...................................... 73 P Setting t[...]

8 Contents 5 7 6 Live View Shooting 125 z Preparing for Live View Shooting ............................................................ 126 z Live View Shooting . ......................................... ........................................ 127 Shooting Function Settings .........................................................................[...]

9 Contents 10 11 8 9 Sensor Cleaning 183 f Automatic Sensor Cleanin g ....................................................................184 Appending Dust Delete Data .......................................................................... 185 Manual Sensor Cleaning ............. ................................................... .............[...]

10 Power Battery • Charging Î p.28 • Calibration Î p.30 • Battery check Î p.35 • Battery information Î p.247 Power outlet Î p.33 Auto power off Î p.52 Lens Attaching/Det aching Î p.39 Basic Settings (Menu Functions) Menus Î p.46 Language Î p.49 Date/Time Î p.49 LCD brightness adjustment Î p.180 Beeper Î p.52 Release shutter with[...]

11 Index to Features Drive Drive modes Î p.101 Maximum burst Î p.62 Self-timer Î p.102 Shooting Program AE Î p.106 Shutter-priority AE Î p.108 Aperture-priority AE Î p.1 10 Manual exposure Î p.1 12 Bulb Î p.1 16 Mirror lockup Î p.1 18 Depth-of-field preview Î p . 111 Exposure adjustment Exposure compensation Î p.1 13 AEB Î p.1 14 AE loc[...]

12 Camera Care This camera is a precision instrument. Do not drop it or subject it to physical shock. The camera is not waterproof and ca nnot be used underwater . If you accidentally drop the camera into wa ter , promptly consult your nearest Canon Service Center . Wipe off any wate r droplets with a dry cloth. If the camera has been exposed to sa[...]

13 Handling Precautions LCD Panel and LCD Monitor Although the LCD monito r is manufactured with very high precision technology with over 99.9 9% effective pixels, there might be a few dead pixels among the remaini ng 0.01% or less pixels. Dead pixels displaying only black or red, etc., are not a malfun ction. They do not affect the images recorded[...]

14 Quick Start Guide 1 Install the battery . (p.32) T ake off the cap and insert a fully- charged battery . T o charge the battery , see page 28. 2 Atta ch the lens. (p.39) Align it with the red dot. 3 Set the lens focus mode switch to <AF>. (p.39) 4 Insert the card. (p.36) The left slot is for a CF card, and the right slot is for an SD card.[...]

15 Quick Start Guide 6 Set the camera to the default settings. (p.53) On the menu screen under the [ 7 ] tab, select [ Clear all camera settings ]. • Press the < M > button and turn the < 6 > or < 5 > dial to select it, then press < 0 >. • The < d > Program AE mode will take effect. 7 Focus the subject. (p.41) Aim [...]

16 Nomenclature Self-timer lamp (p.102) Contacts (p.13) Lens mount Lens lock pin Grip V ertical-grip Main Dial (p.43,42) V ertical-grip shutter button (p.43,41) Depth-of-field preview button (p.1 1 1) Lens release button (p.39) Lens mount index (p.39) Mirror (p.1 18,187) Movie microphone (p.143) Hand strap E1 mount (p.26) Body number Tripod socket [...]

17 Nomenclature Flash-sync contacts Hot shoe < 6 > Main Dial (p.42) < O > Exposure compensation/ Aperture button (p.1 13/1 12) < U > LCD panel illumination button (p.1 16) < I > FE lock/ Multi-spot metering/ Movie shooting button (p.1 19/105/143) < Z > ISO speed setting button (p.64,144) Strap mount (p.26) Power/Quick [...]

18 Nomenclature < Q > Metering mode selection/Flash exposure compensation button (p.104/1 19) < W > Shooting mode selection button (p.106,127,143,144) < o > A F mode selection/ Drive mode selection button (p.94/101) < Y > AEB setting button (p.1 14) Battery release handle (p.32,33) Battery (p.28) Speaker (p.165,175) < V &[...]

19 Nomenclature Strap mount (p.26) < M > Menu button (p.44) T erminal cover < x > Playback button (p.156) Rear LCD panel (p.22) < L > Erase button (p.179) < B > Info/Trimming orientation button (p.128,148,156,246/197) SD card slot (p.36) CF card slot (p.36) Card slot cover (p.36) CF card eject button (p.38) Access lamp (p.38[...]

20 Nomenclature Viewfinder Information The display will show only the settings currently applied. Center spot metering circle Focusing screen < q > Manual exposure < w > AE lock AEB in-progress Multi-spot metering < D > Flash-ready Improper FE lock warning < q > Metering mode < e > High-speed sync (FP flash) < r >[...]

21 Nomenclature T op LCD Panel The display will show only the settings currently applied. Aperture AEB amount Dust Delete Data acquisition ( - - ) Shooting mode d : Program AE f : Aperture-priority AE a : Manual exposure s : Shutter-priority AE Metering mode q Evaluative metering w Partial metering r Spot metering e Center-weighted average metering[...]

22 Nomenclature Rear LCD Panel *1: Displayed when Wireless File Transmitter WFT - E2 II A/B/C/D or WF T -E2/E2A is used. *2: Displayed when the camera is connected to a personal computer or a printer (PictBridge). *3: Displayed when the WFT -E2 II A/B/C/D or WFT-E2/E2A and external media are used. The display will show only the settings currently a[...]

23 Nomenclature Shooting Settings Display The display will show only the settings currently applied. Shooting mode d : Program AE f : Aperture-priority AE a : Manual exposure s : Shutter-priority AE Metering mode q Evaluative metering w Partial metering r Spot metering e Center-weighted average metering < y > Flash exposure compensation < [...]

24 Nomenclature Battery Pack LP-E4 Protective cover Battery release handle Contacts Lock lever Handle end Contact end C OP Y[...]

25 Nomenclature Battery Charger LC-E4 Charger for Battery Pack LP-E4 (p.28). Car battery cable socket Calibration/Performance check button Charge lamp Charge level/ Calibration (Discharge) status indicator/ Performance check lamp Battery pack slot Power cord socket Power cord Protective covers (2) C OP Y[...]

26 Nomenclature Strap Cable Protector Hand strap E1 (Sold separately) Attaching the Neck St rap and Hand Strap E1 Using the Cable Protector Attaching the Neck S trap System extension terminal Interface cable HDMI cable (Sold separately) 1 2 3 4 5 6 After attaching the strap, pull it at th e buckle to t ake up the slack and to make sure it do es not[...]

27 Getting Started This chapter explains pr eliminary steps and basic camera operations. Minimizing Dust When changing lenses, do it quickl y in a place with minimal dust. When storing the came ra without a lens at tached, be sure to attach the body cap to the camera. Remove dust on the body cap before attaching it. C OP Y[...]

28 1 Connect the charger to a power outlet. Connect the power plug to a power outlet, and connect the power cord to the charger . When no battery is attached, all the indicator lamps will be off. 2 Remove the protective covers from the charger and battery . Remove the protective cover on the charger by sliding it out. 3 Recharge the battery . Slide[...]

29 Charging the Battery Recharge the battery on th e day before or on the day it is to be used. Even during storage, a charged ba ttery will gradually discharge and lose its power . After recharging the battery , detach it and unplug the power cord from the power outlet. When not using the batter y and charger , attach the protective covers. Use th[...]

30 Charging the Battery With Car Battery Cable CB-570 (sol d separately), you can connect the charger ’s car battery cable socket (< DC IN > terminal) to your car’s cigarette lighter socket. When recharging the battery this way , be sure that the car ’s engine is running. If the car engine is off, disconnect the car battery cable from t[...]

31 Charging the Battery If all three Charge level indicators b link in green, it means that the battery’s internal temperature is not within 0°C - 40°C / 32°F - 104°F . The battery will start recharging wh en the internal temperature is within 0°C - 40°C / 32°F - 104°F . If all the Calibration (discharge) status indicators blink in red or[...]

32 Insert a fully charged Battery Pack LP-E4 into the camera. 1 Remove the battery compartment cap. 2 Insert the battery . Insert the battery firmly all the way , and turn the release handle as shown by the arrow . 1 Flip out the battery release handle and turn it as shown by the arrow . 2 Pull out the battery . T o prevent shorting, be sure to att[...]

33 With AC Adapter Kit ACK-E4 (sol d separately), you can connect the camera to a household power outle t and not worry about the battery level. 1 Connect the DC Coupler ’ s plug. Connect the DC Coupl er ’s plug to the AC adapter ’s DC terminal. 2 Connect the power cord. Connect the power plug to the power outlet, then connect the power cord [...]

34 < 2 > : The camera is turned off and does not operate. Set to this position when not using the camera. < 1 > : The camera turns on. < J > : The camera and < 5 > operate (p.43). Whenever you set th e power switch to < 1 / J > or < 2 >, the sensor cleaning will be executed automatically . During the sensor clean[...]

35 Turning on the Power When the power switch is set to < 1 >, the battery level will be indicated in one of six levels: Battery Life The figures above are based on a fully-char ged Battery Pack LP-E4, no Live View shooting, and CIP A (Camera & Imaging Products Association) testing standards. Checking the Battery Level Icon Level (%) Indi[...]

36 The camera can use a CF card and SD card. Images can be recorded when at least one card is installed in the camera. If both card slots have a card, you can select which card to record images with or record the same im ages simultaneously on both cards (p.56, 57). If you use an SD card, be sure the card’ s write protect switch is set upward to [...]

37 Installing and Removing the Card 4 Set the power switch to < 1 >. X The number of remaining shots will be displayed on the top LCD panel and in the viewfinder . X The rear LCD panel will indicate which card(s) has been installed. The images will be recorded to the card with the < > arrow next to the respective card’ s indicator . C[...]

38 Installing and Removing the Card 1 Open the cover . Set the power switch to < 2 >. Make sure the access lamp is off, then open the cover . 2 Remove the card. T o remove the CF card, push the eject button. T o remove the SD card, push it in gently and release it. Then pull it out. Close the cover . Removing the Card The access lamp lights o[...]

39 1 Remove the caps . Remove the rear lens cap and the body cap by turning them as shown by the arrow . 2 Atta ch the lens. Align the red dots on the lens and camera and turn the lens as shown by the arrow until it clicks in place. 3 On the lens, set the focus mode switch to < f > (autofocus). If it is set to < g > (manual focus), auto[...]

40 1 Remove the eyecup. While grasping both sides of the eyecup, slide it upward to remove. 2 Make the adjustment. T urn the knob to the right or left until the AF points or the center spot metering circle (p.20) looks sharp in the viewfinder . Attach the eyecup. T o obtain sharp images, hold the camera still to minimize camera shake. 1. Wrap your [...]

41 Basic Operation The shutter button has two steps. Y ou can press the shutter button halfway . Then you can further press the shutter button completely . Pressing halfway This activates autofocusing and automatic exposure metering that sets the shutter speed and aperture. The exposure setting (shutter speed and aperture) is displayed on the top L[...]

42 Basic Operation (1) Af ter pressing a button, turn the < 6 > dial. When you press a button, its function remains selected for 6 seconds ( 9 ). During this time, you can turn the < 6 > dial to set the desired setting. When the function selection turns off or if you press the shutter button halfway , the camera will be ready to shoot. [...]

43 Basic Operation Before using the < 5 > dial, set the power switch to < J >. (1) Af ter pressing a button, turn the < 5 > dial. When you press a button, its function remains selected for 6 seconds ( 9 ). During this time, you can turn the < 5 > dial to set the desired setting. When the function selection turns off or if yo[...]

44 Y ou can set various settings with t he menus such as the beeper , date/ time, etc. While looking at the LCD monitor , use the < M > button on the camera back and the < 6 > < 5 > dials. Menu Operations Icon Color Category Description 1 / 2 Red Shooting menu Shooting-related items 3 / 4 Blue Playback menu Image playback-related [...]

45 Menu Operations 1 Display the menu. Press the < M > button to display the menu. 2 Select a t ab. T urn the < 6 > dial to select a tab. 3 Select the desired item. T urn the < 5 > dial to select the item, then press < 0 >. 4 Select the setting. T urn the < 5 > dial to select the desired setting. The current setting is[...]

46 1 Shooting 1 (Red) Page 2 Shooting 2 (Red) 3 Playback 1 (Blue) Menu Settings White balance Q / W / E / R / Y / U / I / O (1 - 5) / P (2500 - 10000) / PC-1 - 5 72 Custom WB registration Manual registration of white balance data 73 WB SHIFT/BKT WB correction: B/A/M/G bias, 9 levels each WB-BKT : B/A and M/G bias, single-level increments, ±3 level[...]

47 Menu Settings 4 Playback 2 (Blue) Page 5 Set-up 1 (Y ellow) 6 Set-up 2 (Y ellow) Highlight alert Disable / Enable 157 AF point display Disable / Enable 158 Histogram Brightness / RGB 158 Enlarge display Enlarge from image ce nter / Enlarge from selected AF point 161 Image jump w/ 6 1 image / 10 images / 100 images / Date / Folder / Movies / S ti[...]

48 Menu Settings 7 Set-up 3 (Y ellow) Page 8 Custom Functions (Orange) 9 My Menu (Green) Save/load settings on media Save/load camera sett ings to/from the card 238 Regist/apply basic settings The camera’s basic settin gs are registered in and applied to the camera 240 Clear all camera settings Resets the camera to the default settings 53 Copyrig[...]

49 1 Select [Language K ]. Under the [ 6 ] tab, select [ Language K ] (the third item from the top), then press < 0 >. 2 Set the desired language. T urn the < 5 > dial to select the language, then press < 0 >. X The interface language will change. Check if the camera’s date and time are set correctly . If necessary , set the cor[...]

50 Before You Start If the card is new or was previous ly formatted by another camera or personal computer , formatting the ca rd with the camera is recommended. When the card is formatted, all images and data in the card will be erased. Even protected images will be erased, so make sure there is nothing you need to keep. If necessary , transfer th[...]

51 Before You Start About Low-level Formatting When [ g ] is selected, low-level formatti ng is possible. If the writing speed to the SD card is slower than usual or if you want to completely erase the data in the SD card, checkmark [ Low level format ] and format the card. Press the < L > button. In step 3 on the preceding page, press the &l[...]

52 Before You Start T o save battery power , the camera tu rns off automatically after a certain time of non-operation. Y ou can chan ge this auto power-off time. If you do not want the camera to turn off automatically , set this to [ Off ]. After the power turns off, you can turn on the camera again by pressing the shutter button or other button. [...]

53 Before You Start The camera’s shooting settings and menu settings can be reverted to the default. 1 Select [Clear all camera settings]. Under the [ 7 ] tab, select [ Clear all camera settings ], then press < 0 >. 2 Select [OK]. T urn the < 5 > dial to select [ OK ], then press < 0 >. X The camera’s default settings will be [...]

54 Before You Start Camera Settings Live View/Movie Shooting Settings Auto power off 1 min. LV z / k setting Disable Beep On AF mode Live mode Release shutter without card Enable Grid display Off Exposure simulation Enable Review time 2 sec. Highlight alert Disable Movie-recording size 1920x1080 AF point display Disable Registered AF point Canceled[...]

55 Image Settings This chapter explains image -related function settings: Image-recording quality , ISO speed, Picture S tyle, white balance, Auto Lighting Optimizer , lens peripheral illumination correction, etc. C OP Y[...]

56 This Instruction Manual assumes that a CF card or SD card is in the camera. When an external media is used via the Wireless File T ransmitter WFT -E2 II A/B/C/D or WF T -E2/E2A (both sold separately), the < u > icon will appear as the third recording media. It can be selected in the same way as with the CF card < f > and SD card <[...]

57 Selecting the Card to Record or Playback If both the CF card and SD card are inserted into the camera, you can set the recording method for the cards. 1 Select [Record func+media/folder sel.]. Under the [ 5 ] tab, select [ Record func+media/folder sel. ], then press < 0 >. 2 Select [Record func.]. T urn the < 5 > dial to select [ Rec[...]

58 Selecting the Card to Record or Playback When [ Auto switch media ] is set, the card for re cording will switch from f to g to u . When [ Rec. separately ] or [ Rec. to multiple ] is set, the image will be recorded under the same fi le number to both the CF and SD cards. Also, the top LCD panel and viewfinder wi ll display the number of possible[...]

59 Y ou can set the image size (recorded pixels), image type (JPEG or RA W), and JPEG quality (compression rate). 3 / 4 / 5 / 6 will record the image as a JPEG image. In the 1 / K1 / 61 mode, the image will require processing with the software provided. Y ou can set the image size in one of the two ways below . Using the Rear LCD Panel to Set the I[...]

60 Setting the Image-recording Quality Using the Menu Screen to Set the Image Size 1 Select [Image size]. Under the [ 2 ] tab, select [ Image size ], then press < 0 >. 2 Set the image size. T o select a RA W image size, turn the < 6 > dial. T o select a JPEG image size, turn the < 5 > dial. On the screen, the “ ***M (megapixels)[...]

61 Setting the Image-recording Quality Figures for the file size, possible shots, and maximu m burst during continuous shooting are based on C anon’s 4GB testing card and Canon’ s testing standards (JPEG quality 8, ISO 10 0, and S tandard Picture S tyle). These figures will vary depending on the subject, card brand, ISO speed, Picture Style, Cu[...]

62 Setting the Image-recording Quality A RA W image is the raw data output by the image sensor , converted to digital data and recorded on the ca rd as is. Y ou can select from 1 , K1 , or 61 (Commonly referred as RA W in this manual). With RA W images, you can use the pr ovided software to make various adjustments as desired and then generate a JP[...]

63 Setting the Image-recording Quality The recording quality (compression ra te) can be set for each image size 3 / 4 / 5 / 6 . 1 Select [JPEG quality]. Under the [ 2 ] tab, select [ JPEG quality ], then press < 0 >. 2 Select the image size. T urn the < 5 > dial to select the image size, then press < 0 >. 3 Set the desired quality[...]

64 Set the ISO speed (image sensor ’s se nsitivity to light) to suit the ambient light level. 1 Press the < Z > button. ( 9 ) 2 Set the ISO speed. While looking at the top LCD panel or in the viewfinder , turn the < 6 > dial. ISO speed can be set within ISO 100- 12800 in 1/3-stop increments. With “ A ” selected, the ISO speed will[...]

65 Z : Setting the ISO Speed If the ISO speed is set to “ A ”, the actual ISO speed to be set will be displayed when you press the shutter button halfway . As indicated below , the ISO speed will be set automat ically to suit the shooting mode. Default ISO Speed * If the shooting mode is < d > and bounce flash is set wi th an external S p[...]

66 By selecting a Picture S tyle, you can obtain image effects matching your photographic expression or the subject. 1 Press the < A > button. When the camera is ready to shoot, press the < A > button. X The Picture S tyle screen will appear. 2 Select a Picture Style. T urn the < 6 > or < 5 > dial to select a Picture S tyle,[...]

67 A Selecting a Picture Style S Neutral This Picture S tyle is for users wh o prefer to process images with their computer . For natural colors and subdued images. U Faithful This Picture S tyle is for users wh o prefer to process images with their computer . When the subject is captured under a daylight color temperature of 5200K, the color is ad[...]

68 Y ou can customize a Picture Style by adjusting individual p a rameters like [ Sharpness ] and [ Contrast ]. T o see the resulting effect s, take test shots. T o customize [ Monochrome ], see the next page. 1 Press the < A > button. 2 Select a Picture Style. T urn the < 6 > or < 5 > dial to select a Picture S tyle, then press t[...]

69 A Customizing a Picture Style For Monochrome, you can also set [ Filter effect ] and [ T oning effect ] in addition to [ Sharpness ] and [ Contrast ]. k Filter Effect With a filter effect applied to a monochrome image, you can make white clouds or green trees stand out more. l T oning Effect By applying a toning effect, you can create a monochro[...]

70 Y ou can select a base Picture Style such as [ Portrait ] or [ Landscape ], adjust its p arameters as desir ed and register it under [ User Def. 1 ], [ User Def. 2 ], or [ User Def. 3 ]. Y ou can create Picture Styles whose p ara meter settings such as for sharpness and contrast are different. Y ou can also adjust the parameters of a Picture S t[...]

71 A Registering a Picture Style 6 Set the parameter . T urn the < 5 > dial to set the parameter as desired, then press < 0 >. For details, see “Customizing a Picture S tyle” on pages 68-69. Press the < M > button to register the new Picture S tyle. The Picture S tyle selection screen will then reappear . X The base Picture S [...]

72 White balance (WB) is for making the white areas look white. Normally , the < Q > (Auto) setting will ob tain the correct white balance. If natural- looking colors cannot be obtained with < Q >, you can set the white balance manually to suit the respective light source. 1 Press the < B > button. ( 9 ) Press the < B > butt[...]

73 Custom white balance enables you to manually set the white balance for a specific light source for better accuracy . Up to five Custom white balance data can be registered to the camera. Y ou can also append a name (caption) to the registered Custom white balance data. There are two ways to register Cu stom white balance data. Y ou can either ta[...]

74 O Custom White Balance 4 Photograph a solid-white object. The plain, white object should fill the center spot metering circle. Focus manually and set the standard exposure for the white object. Any white balance mode may be set. X The Custom WB data will be registered. T o use the Custom WB, see “Selecting and Shooting with the Custom WB data?[...]

75 O Custom White Balance Register image on card First follow step 4 under “Capture and regi ster the image” (p.73, 74) to take a picture of a plain, white object. This image saved in the card can then be regi stered for Custom WB. The procedure up to step 2 is the same as with “Capture and register the image”. 1 Select [Custom WB regist.].[...]

76 O Custom White Balance 1 Select the Custom WB No. On the Custom WB registration screen, select the No. of the registered Custom WB. 2 Select [Set as white balance]. T urn the < 5 > dial to select [ Set as white balance ], then press < 0 >. X The WB will be set to the registered < O *>. 3 T ake the picture. X The picture will be[...]

77 O Custom White Balance 2 Select [Edit caption]. T urn the < 5 > dial to select [ Edit caption ], then press < 0 >. 3 Enter any name. Press the < H > button, and the text palette will be highlighted in a color frame and text can be entered. Operate the < 5 > dial or < 9 > to move the and select the desired character [...]

78 Y ou can set the white balance’s color temperature numerically in Kelvin. This is for advanced users. 1 Press the < B > button. ( 9 ) Press the < B > button once or twice to display the white balance on the rear LCD panel’s upper right. 2 Select < P >. T urn the < 5 > dial to select < P >. 3 Set the desired colo[...]

79 Y ou can correct the white balance t hat has been set. This adjustment will have the same effect as using a commercially-available color temperature conversion filter or color compensating filter . Each color can be corrected to one of nine levels. This is for advanced users who are fa miliar with using color temperature conversion or color comp[...]

80 u White Balance Correction With just one shot, three images having a different color balance can be recorded simultaneously . Ba sed on the color temperature of the current white balance setting, the image will be br acketed with a blue /amber bias or magenta/green bias. This is called white balance bracketing (WB-BKT). White balance bracketing [...]

81 If the image comes out dark or the cont rast is low , the brightness and contrast can be corrected automatic ally . With JPEG images, the correction is done when the image is captured. Setting information is appended to RA W images and automatic correction is possible with Digital Photo Professional (provided sof tware). By default, [ St andard [...]

82 Due to the lens characteristics, the f our corners of the picture might look darker . This is called lens light fall- off or drop in peripheral illumination. With JPEG images, the correction is done when the image is captured. Setting information is appended to RA W images and automatic correction is possible with Digital Photo Professional (pro[...]

83 3 Lens Peripheral Illumination Correction The camera already contains lens peripheral illumination correction data for approx. 25 lenses. In step 2, if you select [ Enable ], the peripheral light correction will be a pplied automatically for any lens whose correction data has been registered in the camera. With EOS Utility (provided software), y[...]

84 Y ou can freely create and select the folder where the captured images are to be saved. This is optional since a folder will be created automatically for saving captured images. 1 Select [Record func+media/folder sel.]. Under the [ 5 ] tab, select [ Record func+media/folder sel. ], then press < 0 >. 2 Select [Folder]. Select [ Folder ], th[...]

85 3 Creating and Selecting a Folder With the Select folder screen displayed, turn the < 5 > dial to select the desired folder , then press < 0 >. X The folder where the captured images will be saved is selected. Subsequent captured images will be recorded into the selected folder . Selecting a Folder Number of images in folder Folder n[...]

86 The file name has four alphanumeric characters followed by a four-digit image number (p.88) and extension. The first four alphanumeric characters are set upon factory ship ment and unique to the camera. However , you can change it. With “User setting1,” you can change and re gister the four characters as desired. With “User setting2,” if[...]

87 3 Changing the File Name 4 Exit the setting. Enter the required number of alphanumeric characters, then press the < M > button. X The new file name will be registered and the screen in step 2 will reappear . 5 Select the registered file name. T urn the < 5 > dial to select [ File name ], then press < 0 >. T urn the < 5 > [...]

88 The four-digit file number is like the frame number on a roll of film. The captured images are assigned a sequential file number from 0001 to 9999 and saved in one folder . Y ou can change how the file number is assigned. 1 Select [File numbering]. Under the [ 5 ] tab, select [ File numbering ], then press < 0 >. 2 Select the file numberin[...]

89 3 File Numbering Methods The file numbering restart s from 0001 each time the card is replaced or a new folder is created. Even after you replace the card, create a folder , or switch the target card (such as f → g ), the file numbering continues in sequence from 0001 for the images saved. This is c onvenient if you want to organize images acc[...]

90 When you set the copyright information, it will be appended to the image as Exif information. Y ou can check the entered copyright information with the camera. 1 Select [Copyright information]. Under the [ 7 ] tab, select [ Copyright information ], then press < 0 >. 2 Select the desired option. T urn the < 5 > dial, select either [ E[...]

91 3 Setting Copyright Information When you select [ Display copyright info. ] in step 2 on the preceding page, you can check the [ Author ] and [ Copyright ] information that you entered. When you select [ Delete copyright information ] in step 2 on the preceding page, you can delete the [ Author ] and [ Copyright ] information. Checking the Copyr[...]

92 The color space refers to the range of reproducible colors. With this camera, you can set the color space for captured images to sRGB or Adobe RGB. For normal shooting, sRGB is recommended. 1 Select [Color space]. Under the [ 1 ] tab, select [ Color space ], then press < 0 >. 2 Set the desired color sp ace. Select [ sRGB ] or [ Adobe RGB ][...]

93 Setting the AF and Drive Modes The Area AF frame has 45 AF points (39 high-precision cross- type points and 6 AF points ). Y ou can select any one of the 45 AF points to match your composition. Y ou can also select the AF mode and drive mode best matching the shooting co nditions and subject. < f > stands for auto focus. < g > st and[...]

94 Select the AF mode suiting the shooting conditions or subject. 1 On the lens, set the focus mode switch to <AF>. 2 Press the < o > button. ( 9 ) 3 Select the AF mode. While looking at the top LCD panel, turn the < 6 > dial. X : One-Shot AF Z : AI Servo AF E : Selecting the AF Mode C OP Y[...]

95 E : Selecting the AF Mode Suited for still subjects. When you press the shutter button halfway , the camera will focus only once. When focus is achi eved, the AF point which achieved focus will flash in red, and the focus confirmation light < o > in the viewfinder will also light. With evaluative metering, the exposure setting will be set [...]

96 E : Selecting the AF Mode This AF mode is for moving subjects when the focusing distance keep s changing. While you hold down the shutter button halfway , the subject will be focused continuously . The exposure is set at the moment the picture is taken. AF is also possible by pressing the < p > button. Focus T racking with AI Servo AF If t[...]

97 Select one of the 45 AF points to autofocus. Manual selection enables you to select one of the 45 AF poi nts. And automatic selection has the camera automatically select one of the 45 AF points. 1 Press the < S > button. ( 9 ) X The current AF point will be displayed in the viewfinder . 2 Select the AF point. Use < 9 > or turn the &l[...]

98 S Selecting the AF Point T o select a horizontal AF point, turn the < 6 > dial. T o select a vertical AF point, turn the < 5 > dial. If all the peripheral AF points light up, automatic AF point selection will take effect. With the EOS-1D Mark IV, higher precision AF is possible with a maximum aperture brighter than f/2 .8 on a lens o[...]

99 S Selecting the AF Point Maximum f/stop: Up to f/2.8 With the 39 AF points indicated by , high-precision, cross-type AF (both hor izontal- and vertical-line sensitive) is possible during manual AF point selection. The cross-type sensors’ vertical-line sensitivity is approx. two times higher than their horizontal-line sensitivity . The remainin[...]

100 Autofocus can fail to achieve focus (the focus confirmation light < o > blinks) with certain subjects such as the following: Subjects difficult to focus V ery low-contrast subjects (Example: Blue sky , solid-color walls, etc.) Subjects in very low light Extremely backlit or reflective subjects (Example: Car with a highly reflective body ,[...]

101 1 Press the < o > button. ( 9 ) 2 Select the drive mode. While looking at the top LCD panel, turn the < 5 > dial. u : Single shooting When you press the shutter butto n completely , one shot will be take n. o : High-speed continuous shooting (Max. 10 shots per sec.) p : Low-speed continuous shooting (Max. 3 shots per sec.) In the o [...]

102 1 Press the < o > button. ( 9 ) 2 Select either < k > or < l >. Look at the top LCD panel and turn the < 5 > dial to select < k > or < l >. k : 10-sec. self-timer l : 2-sec. self-timer 3 T ake the picture. Look through the viewfinder , focus the subject, then press the shutter button completely . X The self-t[...]

103 Exposure Control Select the shooting mode to suit the subject or shooting objective. Y ou can set the shutter speed and/or aperture to obtain the exposure you want. Also, with an EX-series S peedlite, you can take flash pictures as easily as shooting without flash. First set the power switch to < J >. C OP Y[...]

104 Y ou can select one of four method s to measure the subject brightness. 1 Press the < Q > button. ( 9 ) 2 Select the metering mode. While looking at the top LCD panel, turn the < 6 > dial. q : Evaluative metering w : Partial metering r : Spot metering e : Center-weighted average metering q Evaluative metering This is a general-purpo[...]

105 q Selecting the Metering Mode With multiple spot meter readings , you can see the relative exposure levels of multiple areas in the pict ure and set the exposure to obtain the desired result. 1 Set the metering mode to r spot metering. 2 Press the < I > button. ( 8 ) Aim the spot metering circle over the area where you want a relative exp[...]

106 The camera automatically sets the shutter speed and aperture to suit the subject’s brightness. This is called Program AE. * < d > stands for Program. * AE stands for Auto Exposure. 1 Set the shooting mode to < d >. Press the < W > button and turn the < 6 / 5 > dial to select < d >. 2 Focus the subject. Look throu[...]

107 d : Program AE 4 T ake the picture. Compose the shot and press the shutter button completely . If the “ 30" ” shutter speed and the maximum aperture blink, it in dicates underexposure. Increase the ISO sp eed or use flash. If the “ 8000 ” shutter speed and the minimum aperture blink, it in dicates overexposure. Lower the ISO speed [...]

108 In this mode, you set the shutter speed and the camera automatically sets the aperture to obtain the correct exposure suiting the brightness of the subject. This is called shutter-priority AE. A faster shutter speed can freeze the action or moving subject. Or a slower shutter speed can create a blurred effect, giving the impression of motion. *[...]

109 s : Shutter-Priority AE If the maximum aperture blinks, it indicates underexposure. T urn the < 6 > dial to set a slower shutter speed until the aperture stops blinking or set a higher ISO speed. If the minimum aperture blinks, it indicates overexposure. T urn the < 6 > dial to set a faster shutter speed until the aperture stops bli[...]

110 In this mode, you set the desired aperture and the camera sets the shutter speed automatically to obtain the correct exposure suiting the subject brightness. This is called aperture-priority AE. A higher f/ number (smaller aperture hole) will make more of the foreground and background fall within acceptable focus. On the other hand, a lower f/ [...]

111 f : Aperture-Priority AE Press the depth-of-field preview button to stop down the lens to the current aperture setting. Y ou can check the depth of field (range of acceptable focus) through the viewfinder . Depth-of-Field Preview If the “ 30" ” shutter speed blin ks, it indicates underexposure. T urn the < 6 > dial to set a large[...]

112 In this mode, you set both the shutter speed and aperture as desired. T o determine the exposure, refer to the exposure level indicator in the viewfinder or use a commercially-a vailable exposure meter . This method is called manual exposure. * < a > stands for Manual. 1 Set the shooting mode to < a >. Press the < W > button a[...]

113 Exposure compensation can increase (brighter) or decrease (darker) the standard exposure set by the camera. Y ou can set the exposure compensation up to ±3 stops in 1/3-stop increments. Exposure compensation can be set in the < d / s / f > shooting modes. 1 Check the exposure. Press the shutter button halfway and check the exposure level[...]

114 By changing the shutter speed or ap erture automatically , the camera brackets the exposure up to ±3 st ops in 1/3-stop increment s for three successive shots. This is called AEB. * AEB stands for Auto Exposure Bracketing. 1 Hold down the < W > and < o > buttons simult aneously . ( 9 ) X The < h > icon and “ 0.0 ” will ap[...]

115 Use AE lock when the area of focus is to be different from the exposure metering area or when you want to ta ke multiple shots at the same exposure setting. Press the < A > button to lock the exposure, then recompose and take the shot. This is called AE lock. It is ef fective for backlit subjects. 1 Focus the subject. Press the shutter bu[...]

116 When bulb is set, the shutter stays open as long as you hold down the shutter button completely , and closes when you let go of the shutter button. This is called bulb exposure. Use bulb exposures for night scenes, fireworks, the heavens, and other subjects requiring long exposures. 1 Set the shooting mode to <buLb>. Press the < W >[...]

117 Bulb Exposures If you take a picture without looking at the viewfinder , light entering the eyepiece can throw off the exposure. T o prevent this, slide the eyepiece shutter lever as shown by the arrow to shutter the eyepiece. Y ou need not shutter the eyepiece during Live View shooting or movie shooting. Y ou can connect Remote Switch RS-80N3 [...]

118 Although using the self-timer or Re mote Switch can prevent camera shake, using mirror lockup to prevent camera vibrations (mirror shock) can also help when you use a super telephoto lens or shoot close ups (macro photography). When [ 8 C.Fn III -17: Mirror lockup] is set to [1: Enable] or [2: Enable: Down with SET] (p.226) , shooting with mirr[...]

119 An EX-series S peedlite (sold sepa rately) makes flash photography as easy as shooting without flash. For detailed instructions, see the EX-series S peedlite’ s instruction manual. This camera is a T ype-A camera that can use all the features of EX-series S peedlites. T o set the flash functions and flash Custom Functions with the camera’s [...]

120 D Flash Photography With an EZ/E/EG/ML/TL-series Speedlite set in TTL or A-TTL autoflash mode, the flash can be fired at full output only . Set the camera’s shooting mode to < a > (manual exposure) or < f > (aperture-priority AE) and adjust the aperture setting before shooting. When using a S peedlite which has manual flash mode, [...]

121 When an EX-series S peedlite (suc h as the 580EX II, 430EX II, and 270EX) settable by the camera is attached, you can use the camera’ s menu screen to set the S peedlite’s fl ash function settings and Custom Functions. First attach the S peedl ite to the camera and turn on the S peedlite. 1 Select [External Speedlite control]. Under the [ 2[...]

122 3 Setting the Flash Functions setta ble under [Flash function settings] On the screen, the settable functions and what’ s displayed will differ depending on the Speedlite, current flash mode, flash Custom Function settings, etc. T o see which functions your S peedlit e provides, refer to the S peedlite’s instruction manual. Flash mode With [...]

123 3 Setting the Flash FEB While the flash output is changed aut omatically , three flash shots are taken. For details, see the instru ctions for FEB (Flash Exposure Bracketing) in your S peedlite’s instruction manual. Flash exposure compensation The same setting as “Flash expos ure compensation” on page 1 19 can be done. E-TTL II For normal[...]

124 3 Setting the Flash 1 Select [Flash C.Fn settings]. T urn the < 5 > dial to select [ Flash C.Fn settings ], then press < 0 >. 2 Set the flash function. Tu r n th e < 5 > dial to select the function nu mber , then set the function. The procedure is the same as setting th e camera’s Custom Functions (p.204). In step 1, select [...]

125 Live View Shooting Y ou can shoot while viewing the image on the camera’s LCD monitor . This is called “Live View shooting.” Live View shooting is effective for still subject s which do not move. If you handhold the camera and shoot while viewing the LCD monitor , camera shake can cause blurred images. Using a tripod is recommended. About[...]

126 This sets the camera for Live Vi ew shooting of still photos. T o shoot movies, see page 141. 1 Select [Live View/Movie func. set.]. Under the [ 6 ] tab, select [ Live V iew/ Movie func. set. ], then press < 0 >. 2 Select [L V z / k set.]. T urn the < 5 > dial to select [ LV z / k set. ], then press < 0 >. “L V” stands for[...]

127 1 Select the shooting mode. Press the < W > button and turn the < 6 / 5 > dial to select the shooting mode. 2 Focus the subject. Before shooting, focus with AF or manual focus (p.131-138). When you press the shutter button halfway , the camera will focus with the current AF mode. 3 T ake the picture. Press the shutter button complet[...]

128 z Live View Shooting Each time you press the < B > button, the informat ion display will change. B About the Information Display AF point ( d ) ISO speed Shots remaining Exposure level indicator Upper indicator: Expo sure level/AEB range Lower indicator: Flash ex posure level/FEB range Aperture Shutter speed Picture S t yle Battery check [...]

129 As with normal shooting through the viewfinder , while the Live View image is displayed, you can still use the camera buttons to change settings and playback images. Pressing the < W > < o > < y > < Z > < O > < A > button will display the setting screen on the LCD monitor . T o change the setting, turn the &l[...]

130 During the Live View display , you can still set the menu options. Live View functions are listed below . Under the [ 6 ] tab with the [ Live V iew/ Movie func. set. ] screen, you can set the following functions. AF mode (p.131-137) Y ou can select [ Live mode ], [ u Live mode ], or [ Quick mode ]. Grid display With [ Grid 1 l ] or [ Grid 2 m ][...]

131 The AF modes available are [ Live mode ], [ u Live mode ] (face detection, p.132), and [ Quick mode ] (p.136). If you want to achieve precise focus, set the lens focus mode switch to < MF >, magnify the image, and focus manually (p.138). Select the AF mode. While the Live View image is displayed, press the < o > button. ( 9 ) T urn [...]

132 Using AF to Focus 2 Focus the subject. Aim the AF point over the subject and press the shutter button halfway . X When focus is achieved, the AF point will turn green a nd the beeper will sound. X If focus is not achieved, the AF point will turn orange. 3 T ake the picture. Check the focus and exposure, then press the shutter button completely [...]

133 Using AF to Focus 2 Focus the subject. Press the shutter button halfway and the camera will focus the face covered by the < p > frame. X When focus is achi eved, the AF point will turn green a nd the beeper will sound. X If focus is not achieved, the AF point will turn orange. If a face cannot be detected, the AF point < > will be d[...]

134 Using AF to Focus AF operation Focusing will take slightly longer . Even when focus has been achieved, pressing the shutter button halfway will focus again. The image brightness may cha nge during and after the AF operation. If the light source changes while th e Live View image is displayed, the screen might flicker and focusing can be difficu[...]

135 Using AF to Focus Shooting conditions which can make focusing difficult: Low-contrast subjects such as the blue sky and solid-color , flat surfaces. Subjects in low light. S tripes and other patterns where there is contrast only in the horizontal direction. Under a light source whose brightness, color , or pattern keeps changing. Night scenes o[...]

136 Using AF to Focus The dedicated AF sensor is used to focus in the One-Shot AF mode (p.95), using the same AF me thod as with viewfinder shooting. Although you can focus th e target area quickly , the Live View image will be interrupted momentarily during the AF operation . 1 Select the AF point. Press the < o > button, then use < 9 >[...]

137 Using AF to Focus 2 Focus the subject. Aim the AF point over the subject and press the shutter button halfway . X The Live View image will turn of f, the reflex mirror will go back down, and AF will be executed. X When focus is achieved, the beeper will sound and the AF point will be displayed in red. (If automatic AF point selection has been s[...]

138 Y ou can magnify the image and focus precisely manually . 1 Set the lens focus mode switch to <MF>. T urn the lens focusing ring to focus roughly . 2 Move the magnifying frame. Use < 9 > to move the magnifying frame to the position where you want to focus. Pressing < 9 > straight down will return the magnifying frame to the im[...]

139 Live View Shooting Cautions Notes About the Live View Image Under low or bright light conditions, the Live View image might not reflect the brightness of the captured image. If the light source within the image changes, the screen might flicker . If this happens, stop and resume the Live View shooting under the actual light source to be used. I[...]

140 Live View Shooting Cautions Notes About the Sh ooting Result s When you shoot with the Live View function at high ISO speeds, noise (horizontal banding, dots of light, et c.) or irregular colors may appear . When you shoot continuous ly with the Live View function for a long period, the camera’s internal temp erature may increase and it can d[...]

141 Shooting Movies The Live View image can be recorded to the card as a movie. A movie can be shot with automatic exposure or manual exposure. The movie recording format will be MOV . Cards which can record movies When shooting movies, use a larg e-capacity card with a fast writing/reading speed. The CF card’s speed should be 8MB/ sec. or higher[...]

142 Set the camera to record the Live Vi ew image as a movie. T o shoot still photos, see page 125. 1 Select [Live View/Movie func. set.]. Under the [ 6 ] tab, select [ Live V iew/ Movie func. set. ], then press < 0 >. 2 Select [L V z / k set.]. T urn the < 5 > dial to select [ LV z / k set. ], then press < 0 >. “L V” stands f[...]

143 When the shooting mode is set to a shooting mode other than < a >, autoexposure control will take ef fect to fit the scene current brightness. Autoexposure control will be the same for all shooting modes. 1 Set a shooting mode other than < a >. Press the < W > button and turn the < 6 / 5 > dial to select a shooting mode [...]

144 k Shooting Movies When the shooting mode is < a >, you can manually set the ISO speed, shutter speed, and aperture for movie shooting. 1 Set the shooting mode to < a >. Press the < W > button and turn the < 6 / 5 > dial to select < a >. 2 Set the ISO speed. Press the < Z > button and look at the screen while [...]

145 k Shooting Movies 3 Set the shutter speed and aperture. Press the shutter button halfway and check the exposure level indicator . T urn the < 6 > dial to set the shutter speed within 1/30 (1/60) sec. to 1/4000 sec. If you set the power switch to < J > and turn the < 5 > dial, you can set the aperture. 4 Focus and shoot the mov[...]

146 k Shooting Movies About the ISO speed during manual exposure The ISO speed can be set to [ AUTO ] ( A ) or within ISO 100-12800 in 1/3-stop increments. If the ISO speed is set to [ AUTO ] ( A ), the ISO speed will be set automatically within ISO 100-12800. (The [ 8 C.Fn I -3: Set ISO speed range ] (p.208) setting will not take effect.) Movie sh[...]

147 k Shooting Movies Notes for autoexposure and manual exposure shooting Even if the [ 5 Record func+media/folder sel. ] menu option has been set to [ Rec. separately ] or [ Rec. to multiple ] (p.57), a movie cannot be recorded simultaneously to both the CF card < f > and SD card < g >. If [ Rec. separately ] or [ Rec. to multiple ] ha[...]

148 k Shooting Movies Each time you press the < B > button, the information display will change. B About the Information Display AE lock ISO speed Exposure level Aperture Shutter speed Picture S t yle Battery check F : Movie display White balance S t ill photo image size AF mode • d : Live mode • c : Face detection Live mode • f : Quick[...]

149 k Shooting Movies Y ou can take a still photo at anytime by pressing the shutter button completely , even during movie shooting. The still photo will record the entire screen including the semi- transparent mask. The still photo will be taken at th e exposure setting displayed when you press the shutter button halfway . If a still photo is shot[...]

150 k Shooting Movies As with normal shooting through the viewfinder , during movie shooting, you can still use the camera buttons to change function settings and execute playback. Pressing the < W >, < o >, < O > or < A > button will display the respective setting screen on the LCD monitor . T o change t he setting, turn th[...]

151 During movie shooting, you can st ill set the menu options. Movie shooting functions are listed below . Under the [ 6 ] tab with the [ Live V iew/ Movie func. set. ] screen, you can set the following functions. AF mode (p.131-137) Y ou can select [ Live mode ], [ u Live mode ], or [ Quick mode ]. Note that the camera cannot focus a moving subje[...]

152 3 Menu Function Settings T otal Movie Recording T ime and File Size Per Minute (Approx.) After you start shooting a movie, the movie shooting wi ll stop automatically if the file size reaches 4 GB or if the movie time reaches 29 min. 59 sec. T o start movie shooting again, press the < I > button. (A new movie file starts being recorded.) [...]

153 Movie Shooting Cautions Recording and Image Quality When you shoot movies at high ISO speeds, noise (horizontal banding, dots of light, etc.) or ir regular colors may appear . If the attached lens has an Image S tabilizer , the Image S tabilizer will operate at all times even if you do not press th e shutter button halfway . The Image S tabiliz[...]

154 Movie Shooting Cautions About the < E > icon and camera's internal temperature increase When you shoot movies continuously for a long period or in high temperatures, the camera's internal temperature may increase and the < E > icon may appear on the screen. No te that if you shoot movies for a long period in high temperatu[...]

155 Image Playback This chapter explains how to playback and erase photos and movies, how to view them on a TV screen, and other playback-related functions. About images taken with another camera: The camera might not be able to properly di splay images captured with a different camera or edited wi th a computer or whose file name or file format wa[...]

156 1 Playback the image. Press the < x > button. X The last captured image or last image viewed will appear . 2 Select the image. T o playback images starting with the last image, turn the < 5 > dial counterclockwise. T o playback images starting with the first captured image, turn the dial clockwise. Each time you press the < B >[...]

157 x Image Playback About the Highlight Alert When the [ 4 Highlight alert ] menu option is set to [ Enable ], overexposed highlight areas will blin k. T o obtain more image detail in the overexposed areas, set the exposure compensation to a negative amount and shoot again. B Shooting Information Display Flash exposure compensation amount Metering[...]

158 x Image Playback About the AF Point Display When the [ 4 AF point disp. ] menu option is set to [ Enable ], the AF point which achieved focus will be disp layed in red. If automatic AF point selection was used, multiple AF points might be displayed in red. About the Histogram The brightness histogram display shows the exposure level distributio[...]

159 Search for images quickly with the index display showing four or nine images on one screen. 1 T urn on the index display . During image playback, press the < y > button. X The 4-image index display will appear . The currently-selected image will be highlighted in a blue frame. Press the < y > button again to switch to the 9-image in[...]

160 x Searching for Images Quickly With the single image display , you can turn the < 6 > dial to jump through the images. 1 Select the jump method. With the [ 4 Image jump w/ 6 ] menu option, select the desired jump method from [ 1 image/10 images/ 100 images/Date/Folder/Movies/ Stills ], then press < 0 >. 2 Browse by jumping. Press th[...]

161 Y ou can magnify the image by 1. 5x to 10x on the LCD monitor . 1 Magnify the image. During image playback, press the < u > button. X The image will be magnified. If you hold down the < u > button, the image will continue to be magnified until it reaches the maximum magnification. T o reduce the magnification, press the < y > [...]

162 Y ou can rotate the displayed image to the desired orientation. 1 Select [Rotate]. Under the [ 3 ] tab, select [ Rot ate ], then press < 0 >. 2 Select the image. T urn the < 5 > dial to select the image to be rotated. Y ou can also select an image on the index display . 3 Rot ate the image. Each time you press < 0 >, the image[...]

163 Basically , there are the following thr ee ways to playback the movies you shot. Use the provided stereo A V cable or HDMI Cable HTC-100 (sold separately) to connect the camera to a TV set. Y ou can then playback the captured movies and photos on the TV . If you have a High-Definition TV set and connect your camera to it with an HDMI cable, you[...]

164 k Enjoying Movies (See the PDF file instruction manu al for ZoomBrowser EX/ImageBrowser) The movie files recorded in the card can be transferred to a personal computer and played or edited with ZoomBrowser EX/ImageBrowser (provided software). Y ou can also extract a single frame from a movie and save it as a still photo. Playback and Editing wi[...]

165 1 Playback the image. Press the < x > button to playback images. 2 Select a movie. T urn the < 5 > dial to select an image. With the single-image display , the < 1s > icon displayed on the upper left indicates that it is a movie. During the index display , the perforation on the left edge of the image indicates that it is a mo[...]

166 k Playing Movies Function Playback Description Exit Returns to the single-image display . 7 Play Pressing < 0 > toggles between play and stop. 8 Slow motion Adjust the slow motion speed by turning the < 5 > dial. The slow-motion speed is indi cated on the upper right. 5 First frame Displays the movie’s first frame. 3 Previous fram[...]

167 Y ou can edit out the first and last scenes of a movie in 1-sec. increments. 1 On the movie playback screen, select [ X ]. X The editing screen will be displayed. 2 Specify the p arts to be edited out. Select either [ ] (Cut beginning) or [ ] (Cut end), then press < 0 >. Ti lt < 9 > to the left or right to see the previous or next f[...]

168 Y ou can playback the images in the card as an automatic slide show . 1 Select [Slide show]. Under the [ 4 ] tab, select [ Slide show ], then press < 0 >. 2 Select the images to be played back. T urn the < 5 > dial to select the item shown on the left, then press < 0 >. [All images/Movies/Stills] T urn the < 5 > dial to [...]

169 3 Slide Show (Auto Playback) 3 Set the play time and repeat option. T urn the < 5 > dial to select [ Set up ], then press < 0 >. For still photos, set the [ Play time ] and [ Repeat ] options, then press the < M > button. 4 St art the slide show. T urn the < 5 > dial to select [ Start ], then press < 0 >. X After [[...]

170 Y ou can view the still photos and mo vies on a TV set. Before connecting or disconnecting the cabl e between the camera an d television, turn off the camera and television. * Adjust the movie’s sound volume with the TV set. T o playback movies, see page 165. * Depending on the TV se t, part of the image di splayed might be cut of f. 1 Connec[...]

171 Viewing the Images on TV The HDMI Cable HTC-100 (sold separately) is required. 1 Connect the HDMI cable to the camera. Connect the HDMI cable to the camera’s < D > terminal. With the plug’s < d HDMI MINI > logo facing the back of t he camera, insert it into the < D > terminal. 2 Connect the HDMI cable to the TV set. Connec[...]

172 Protecting the image prevents it from being erased accidentally . 1 Select the image to be protected. Press the < x > button to playback images, then turn the < 5 > dial to select an image. 2 Protect the image. During image playback, press the < H > button. X When an image is protected, the < K > icon will appear on the [...]

173 J Protecting Images If you format the card (p.50) , the protected images will also be erased. T o protect an image, press and quickly let go of the < H > button. If you hold down the button for approx. 2 sec ., a voice memo will be recorded. Images can also be protecte d individually when the [ 3 Protect images ] menu option is set to [ S[...]

174 Y ou can append a voice memo to a captured image. The voice memo will be saved as a W A V sound file having t he same file number as the image. The sound can be played back with t he camera or provided software. 1 Select the image to which you want to append a voice memo. Press the < x > button to playback images, then turn the < 5 >[...]

175 K Recording and Playing Voice Memos When [ 8 C.Fn IV -9: H button function] is set to [2: Play me mo (hold: Record memo)] (p.231) , the voice memo appended to the ima ge can be played back. 1 Set [ 8 C.Fn IV -9: H button function] to [2: Play memo (hold: Record memo)]. Set this function while referring to page 231. For details on setting a Cust[...]

176 The images recorded in a card ca n be copied to the other card. 1 Select [Image copy]. Under the [ 3 ] tab, select [ Image copy ], then press < 0 >. 2 Select [Sel.Image]. Check the copy source and target card’s cap acity . T urn the < 5 > dial to select [ Sel.Image ], then press < 0 >. 3 Select the folder . T urn the < 5 [...]

177 a Copying Images 4 Select the image. T urn the < 5 > dial to select the image to be copied, then press < 0 >. X The < X > icon will appear on the upper left of the screen. Press the < y > button to display the three-image view . T o return to the single- image display , press the < u > button. T o select another im[...]

178 a Copying Images X The copying will start and the progress will be displayed. When the copying is completed, the result will be displayed. Select [ OK ] to return to the screen in step 2. In step 2, select [ Sel. n ]. Select the source folder to be copied, then the target folder . In step 2, select [ All image ]. All the folders and images in t[...]

179 Y ou can either select and erase images one by one or erase them in one batch. Protected images (p.172) will not be erased. Once an image is erased, it ca nnot be recovered. Make sure you no longer need the image before er asing it. T o prevent important images from being erased acciden tally , protect them. Erasing a RA W+JPEG image will erase[...]

180 Y ou can adjust the brightness of the LCD monitor to make it easier to read. 1 Select [LCD brightness]. Under the [ 6 ] tab, select [ LCD brightness ], then press < 0 >. 2 Adjust the brightness. While referring to the gray chart, turn the < 5 > dial, then press < 0 >. Changing Image Playback Settings 3 Adjusting the LCD Monito[...]

181 Changing Image Playback Settings Y ou can set how long the image is displayed on the LCD monitor immediately after capture. T o keep the image displayed, set [ Hold ]. T o not have the image displayed, set [ Off ]. 1 Select [Review time]. Under the [ 2 ] tab, select [ Review time ], then press < 0 >. 2 Set the desired time. T urn the <[...]

182 Changing Image Playback Settings V ertical images are rotated automatically so they are displayed vertically on the camera’s LCD monitor and computer instead of horizontally . The setting of this feature can be changed. 1 Select [Auto rot ate]. Under the [ 5 ] tab, select [ Auto rota te ], then press < 0 >. 2 Set the auto rot ation. T u[...]

183 Sensor Cleaning The camera has a Self Cleani ng Sensor Unit attached to the image sensor ’s front layer (low-pass filter) to shake off dust automatically . The Dust Delete Data can also be appended to the image so that the dust spot s remaining can be erased automatically by Digital Photo Professional (provided software). About smear adhering[...]

184 Whenever you set the power switch to < 1 / J > or < 2 >, the Self Cleaning Sensor Unit operates to automatically shake off any dust on the front of the sensor . Normally , you need not pay attent ion to this operation. However , you can execute the sensor cleaning at anytime as well as disable it. 1 Select [Sensor cleaning]. Under t[...]

185 Normally , the Self Cleaning Sensor Un it will eliminate most of the dust that might be visible on captured im ages. However , in case visible dust still remains, you can append the Dust Delete Data to the image to later erase the dust spots. The Dust Delete Data is used by Digit al Photo Professional (provided software) to erase the dust spots[...]

186 3 Appending Dust Delete Data 3 Photograph a solid-white object. At a distance of 20 cm - 30 cm / 0.7 ft. - 1.0 ft., fill the viewfinder with a patternless, solid-white object and take a picture. X The picture will be taken in the aperture- priority AE mode with an aperture of f/22. Since the image will not be saved, the data can still be obt a [...]

187 Dust which could not be removed by the automatic sensor cleaning can be removed manually with a blower , etc. The surface of the image sensor is extremely delicate. If the sensor needs to be cleaned directly , having it done by a Canon Service Center is recommended. Before cleaning the sensor , det ach the lens from the camera. 1 Select [Sensor[...]

188 3 Manual Sensor Cleaning While cleaning the sensor , n ever do any of the following. If the power is cut off, the shutter will close and the shutter curtains and image sensor might get damaged. • Setting the power switch to < 2 >. • Removing or inserting the battery . The surface of the image sensor is extrem ely delicate. Clean the s[...]

189 Printing Images Printing (p.190) Y ou can connect the camera directly to a printer and print out the images in the card. The camera is compatible with “ w PictBridge” which is the standard for direct printing. Digital Print Order Format (DPOF) (p.199) DPOF (Digital Print Order Fo rmat) enables you to print images recorded in the card accord[...]

190 The direct printing procedure is done entirely with the camera while you look at the LCD monitor . 1 Set the camera’ s power switch to < 2 >. 2 Set up the printer . For details, see the printer’s instruction manual. 3 Connecting the camera to a printer Use the interface cable provided with the camera. When connecting the cable plug to[...]

191 Preparing to Print 6 Playback the image. Press the < x > button. X The image will appear , and the < w > icon will appear on the upper left to indicate that the camera is connected to a printer . w PictBridge Movies cannot be printed. The camera cannot be used with printers compatible only with CP Direct or Bubble Jet Direct. Do not[...]

192 The screen display and setting options will differ depending on the printer . Some settings might not be available. For details, see the printer ’s instruction manual. 1 Select the image to be printed. Check that the < w > icon is displayed on the upper left of the LCD monitor . T urn the < 5 > dial to select the image to be print[...]

193 w Printing T urn the < 5 > dial to select the size of the paper loaded in the printer , then press < 0 >. X The paper type screen will appear . T urn the < 5 > dial to select the type of the paper loaded in the printer , then press < 0 >. When using a Canon printer and Canon paper , read the printe r ’s instruction man[...]

194 w Printing 4 Set the printing effects. Set as necessary . If you need not set any printing effects, go to step 5. T urn the < 5 > dial to select the item on the upper right, then press < 0 >. If the < e > icon is displayed next to < z >, you can also adjust the printing effect (p.196). Next, turn the < 5 > dial to [...]

195 w Printing 5 Set the date and file number imprinting. Set as necessary . T urn the < 5 > dial to select < I >, then press < 0 >. T urn the < 5 > dial to select the desired setting, then press < 0 >. 6 Set the number of copies. Set as necessary . T urn the < 5 > dial to select < R >, then press < 0 &g[...]

196 w Printing In step 4 on page 194, select the printing effect. When the < e > icon is displayed next to < z >, press the < B > button. Y ou can then adjust the printing effect. What can be adjusted or what is displayed will depend on the selection made in step 4. Brightness The image brightness can be adjusted. Adjust levels Wh[...]

197 w Printing Y ou can crop the image and print only the trimmed portion as if the image was recomposed. Do the trimming right before printing. If you set the trimming and then set the print settings, you may have to set the trimming again. 1 On the print setting screen, select [T rimming]. 2 Set the trimming frame size, position, and aspect ratio[...]

198 w Printing Depending on the printer , the trimmed image area might not be printed as you specified. The smaller you make the trimming fr ame, the grainier the picture will look on the print. While trimming the image, look at th e camera’s LCD monitor . If you look at the image on a TV sc reen, the trimming frame might not be displayed accurat[...]

199 Y ou can set the print type, date impr inting, and file No. imprinting. The print settings will be applied to al l print-ordered images. (They cannot be set individually for each image.) 1 Select [Print order]. Under the [ 3 ] tab, select [ Print order ], then press < 0 >. 2 Select [Set up]. T urn the < 5 > dial to select [ Set up ][...]

200 W Digital Print Order Format (DPOF) 4 Exit the setting. Press the < 7 > button. X The print order screen will reappear . Next, select [ Sel.Image ], [ By n ], or [ All image ] to order the images to be printed. Option Description Print type K S tandard Prints one image on one sheet. L Index Multiple, thumbnail images are printed on one sh[...]

201 W Digital Print Order Format (DPOF) Sel.Image Select and order images one by one. Press the < y > button to display the three-image view . T o return to the single- image display , press the < u > button. After completing the print order , press the < M > button to save the print order to the card. [St andard] [Both] Press <[...]

202 With a PictBridge printer , you can easily print images with DPOF . 1 Prep are to print. See page 190. Follow the “Connecting the Camera to a Printer” procedure up to step 5. 2 Under the [ 3 ] t ab, select [Print order]. 3 Select [Print]. [ Print ] will be displayed only if the camera is connected to the printer and printing is possible. 4 [...]

203 Customizing the Camera T o suit your shooting prefer ences, you can fine-tune the camera’s functions, save the camera settings to a card or register them to the camera. C OP Y[...]

204 1 Select [ 8 ]. T urn the < 6 > dial to select the [ 8 ] tab. 2 Select the group. T urn the < 5 > dial to select C.Fn I - IV , then press < 0 >. 3 Select the Custom Function number . T urn the < 5 > dial to select the Custom Function No., then press < 0 >. 4 Change the setting as desired. T urn the < 5 > dial[...]

205 3 Custom Functions C.Fn I: Exposure z LV shooting k Movie shooting 1 Exposure level increments p.208 k 2 ISO speed setting increments k In M movie mode 3 Set ISO speed range k In M movie mode 4 Bracketing auto cancel p.209 k (S till photo with WB-BKT) 5 Bracketing sequence k 6 Number of bracketed shots k 7 S p ot metering link to AF point p.210[...]

206 3 Custom Functions C.Fn II: Image/Flas h exposure/Display z LV shooting k Movie shooting 1 Long exposure noise reduction p.214 k (S till photo) 2 High ISO speed noise reduction k (S till photo) 3 Highlight tone priority p.215 k 4 Auto Lighting Optimizer k 5 E-TTL II flash metering k 6 S hutter curtain sync. p.216 k 7 Flash firing k 8 Viewfinder[...]

207 3 Custom Functions 13 AF point display during focus p.225 With f 14 AF point brightness With f 15 AF-assist beam firing With f 16 Orientation linked AF point p.226 With f 17 Mirror lockup 18 Continuous shooting speed k 19 Limit continuous shot count p.227 k C.Fn IV : Operation/Others z LV shooting k Movie shooting 1 Shutter button/AF-ON button [...]

208 Custom Functions are organized in four groups based on the function type: C.Fn I: Exposure, C.Fn II: Image/Flash exp (exposure)/Disp (Display), C.Fn III: Autofocus/Drive, and C.Fn IV : Operation/Others. Note that some Custom Funct ion numbers differ from the EOS-1D Mark III’ s Custom Functions. 3 Custom Function Settings C.Fn I: Exposure C.Fn[...]

209 3 Custom Function Settings C.Fn I -4 Bracketing auto cancel 0: On The AEB and WB-BKT settings will be canceled if you set the power switch to < 2 > or clear the camera se ttings. AEB will also be canceled when bulb exposure is set or the flash is ready to fire. 1: Off The AEB and WB-BKT settings wil l be retained even when the power switc[...]

210 3 Custom Function Settings C.Fn I -7 Spot metering link to AF point 0: Disable (use center AF point) 1: Enable (use active AF point) If [ 8 C.Fn III -10: Selectable AF point ] (p.2 23) is set to [ 1: 19 points ], [ 2: 1 1p oints ], [ 3: Inner 9 point s ] or [ 4: Outer 9 point s ], spot metering linked to the selected AF point is possible. With [...]

211 3 Custom Function Settings C.Fn I -10 Select usable metering modes Disable: All the metering modes ( q : Evaluative, w : Partial, r : S pot, e : Center-weighted average) will be selectable. Enable: Only the metering modes set with [ Register ] will be selectable. Register: T o make a metering mode unselec table, uncheck the checkmark < X >[...]

212 3 Custom Function Settings C.Fn I -14 Apply shooting/metering mode While holding down the < A > (AE lock) button, you can switch to the registered setting (shooting mode, me tering mode, shutte r speed, aperture, or exposure compensation). Disable: Pressing the < A > button will lock the exposure (AE lock). Enable: By holding down t[...]

213 3 Custom Function Settings C.Fn I -16 AE Microadjustment Normally , this adjustment is no t required. Do this adjustment only if necessary . Note that doi ng this adjustment may prevent correct exposure from being achieved. Y ou can fine adjust the camera’s standar d exposure level. The adjustment can help if the camera’s “sta ndard expos[...]

214 3 Custom Function Settings C.Fn II: Image/Flash exposure/Display C.Fn II -1 Long ex posure noise reduction 0: Off 1: Auto For 1 sec. or longer exposure s, noise reduction is performed automatically if noise typical of long exposures is detected. This [ Auto ] setting is effective in most cases. 2: On Noise reduction is performed for all ex posu[...]

215 3 Custom Function Settings C.Fn II -3 Highlight tone priority 0: Disable 1: Enable Improves the highlight detail. The dynamic range is expanded from the standard 18% gray to br ight highlight s. The gr adation between the grays and highlights becomes smoother . C.Fn II -4 Auto Lighting Optimizer If the image comes out dar k or the contrast is l[...]

216 3 Custom Function Settings C.Fn II -6 Shutter curtain sync. 0: 1st-curt ain synchronization 1: 2nd-curt ain synchronization The flash fires immediately befor e the exposure ends. When this is combined with a slow sync speed, you can create a trail of light such as from car headlights at night. This Custom Function can be used to ob tain 2nd-cur[...]

217 3 Custom Function Settings C.Fn II -9 LCD panel illumination during Bulb 0: Off 1: On during Bulb If the LCD panel illumination is on (p .1 16) and you take a bulb exposure, the illumination will continue until the bulb exposure ends. This is convenient when you are taking a bulb exposure in low light and want to check the exposure time. C.Fn I[...]

218 3 Custom Function Settings C.Fn III: Autofocus/Drive C.Fn III -1 USM lens electronic MF The USM lens electronic MF can be enabled or disabled when you use any of the following lenses. EF50mm f/1.0L USM, EF85mm f/1.2L USM, EF85mm f/1.2L II USM, EF200mm f/1.8L USM, EF300mm f/2.8L USM, EF400mm f/2.8L USM, EF400mm f/2.8L II USM, EF500mm f/4.5L USM,[...]

219 3 Custom Function Settings 2: Release/Drive speed priority For the first shot, shutter release is given priority over focusing the subject. During continuous shooting, the continuous shooting speed is given priority more than with setting 1. 3: Release/T racking priority For the first shot, shutter release is given priority over focusing the su[...]

220 3 Custom Function Settings C.Fn III -6 Lens AF stop button function * The AF stop button is provided on ly on super telephoto IS lenses. 0: AF stop 1: AF start AF operates only while the button is pressed. While you hold down the button, AF will not work on the camera. 2: AE lock When the button is pre ssed, AE lock is applied. Convenient when [...]

221 3 Custom Function Settings C.Fn III -7 AF Microadjustment Normally , this adjustment is no t required. Do this adjustment only if necessary . Note that doi ng this adjustment may prevent correct focusing from being achieved. Y ou can make fine adjustments for the AF’s point of focus. It can be adjusted in ±20 steps (-: Forward / +: Backward)[...]

222 3 Custom Function Settings C.Fn III -8 AF expa nsion with selected point During manual AF point selection, it is possible to activate the AF points surrounding the selected AF point for AF . This function works in both the One-Shot AF and AI Servo AF modes. Convenient when it is difficult to tr ack a moving subject with just one manually-select[...]

223 3 Custom Function Settings C.Fn III -9 Multi-controller while metering 0: Off 1: AF point selection During viewfinder shooting while the me tering is active, you can select the AF point directly with < 9 > instead of pressing the < S > button first. C.Fn III -10 Select able AF point Y ou can change the number of manually-selectable [...]

224 3 Custom Function Settings C.Fn III -1 1 Switch to registered AF point Y ou can instantly switch to th e registered AF point with < 9 > or the < w > button while the metering timer is ac tive. The AF will operate when the switch is made. 0: Disable 1: Switch with < 9 > By pressing < 9 >, you can switch to the r egistered[...]

225 3 Custom Function Settings C.Fn III -13 AF point display during focus 0: On 1: Off The AF point will not light in red other than during AF point selection. 2: On (when focus achieved) During AF , the manually-selected AF poi nt will no longer light faintly . After AF start s, the AF point will light only when it achieves focus. C.Fn III -14 AF [...]

226 3 Custom Function Settings C.Fn III -16 Orientation linked AF point Y ou can either use the same AF point or a different AF point for vertical and horizontal shooting. 0: Same for both vertical/horizontal The same AF point is used for both vertical and horizontal shooting. 1: Select different AF points A different AF point can be set sepa ratel[...]

227 3 Custom Function Settings C.Fn III -19 Limit continuous shot count Disable: Continuous shooting is not limi ted to any number of shots. Continuous shooting will be possi ble up to the current maximum burst displayed. Enable: The continuous shooting will be limited to the number of shots set with [ Register ] after which the shooting will stop [...]

228 3 Custom Function Settings C.Fn IV -3 Quick Control Dial in metering The Quick Control Dial’s function wh ile the metering is active can be changed. 0: Exposure compensation/Aperture 1: AF point selection Y ou can select the AF point directly with the < 5 > dial without first pressing the < S > button. While metering is active, tu[...]

229 3 Custom Function Settings C.Fn IV -4 Assign SET button Y ou can assign a frequently-used function to < 0 >. Press < 0 > when the camera is shooting-ready . 0: Normal (disabled) 1: White balance While looking at the rear LCD pa nel, you can change the white balance. 2: Image size While looking at the rear LCD panel, you can change t[...]

230 3 Custom Function Settings C.Fn IV -6 Dial direction during Tv/A v 0: Normal 1: Reverse direction The dial’s turning direction for setting the shutter speed and aperture can be reversed. In the manual exposure mode, the direction of the < 6 > and < 5 > dials will be reversed. In other shooting modes, the < 6 > dial will be r[...]

231 3 Custom Function Settings C.Fn IV -9 H button function 0: Protect (hold: Record memo) When you hold down the < H > button for 2 sec., you can start recording a voice memo. When you let go of the button, the voice memo recording will stop. 1: Record memo (Protect: Disabled) When you press the < H > button, you can start recording a [...]

232 3 Custom Function Settings C.Fn IV -1 1 Start movie shooting 0: Default (from L V) 1: Quick start (< I > button) If the [ 6 Live View/Movie func. set. ] menu option has been set to enable movie shooting (p.142), press the < I > button to start shooting a movie immediately while the camera is ready to shoot. C.Fn IV -12 Focusing Scre[...]

233 3 Custom Function Settings C.Fn IV -13 Timer length for timer How long the function setting remains in effect after you let go of the respective button can be changed. Disable: The timer length is set to the default. Enable: The timer length is set to the time set with [ Register ]. Register: Y ou can set the 6-sec. and 16-s ec. timer length an[...]

234 3 Custom Function Settings C.Fn IV -15 Add as pect ratio information During Live View and movie shooting, vertical lines corresponding to the aspect ratio will be displayed. Y ou can thereby simulate still photo framing for medium- and large-format film size s such as 6x6 cm, 6x4.5 cm, and 4x5 in. This aspect ratio information will be appended [...]

235 Y ou can register up to three sets of Custom Function settings. Y ou can register a different set of Custom Function settings for different shooting situations such as s ports, snapshot s, and landscapes. Y ou can then instantly apply a registered set of Custom Function settings. 1 Select [C.Fn setting register/ apply]. Under the [ 8 ] tab, sel[...]

236 3 Registering and Applying Custom Function Settings In step 2, select [ Apply ] and select the [ Set * ] of the Custom Function settings to be applied. Select [ OK ], and the Custom Function settings will switch to those registered under Set *. Applying Custom Function Settings The settings for [ 8 C.Fn I -16: AE Microadjustment ], [ 8 C.Fn I -[...]

237 Under the My Menu tab, you can regi ster up to six menu options and Custom Functions whose settings you change frequently . 1 Select [My Menu settings]. Under the [ 9 ] tab, select [ My Menu settings ], then press < 0 >. 2 Select [Register]. T urn the < 5 > dial to select [ Register ], then press < 0 >. 3 Register the desired [...]

238 The camera’s shooting modes, menu s, Custom Functions, and other camera settings can be saved in the card as a camera settings file. When this file is loaded by the ca mera, the saved camera settings will be applied. Convenient when you want to load the camera settings from a different EOS-1D Mark IV body and set the came ra in the same way .[...]

239 3 Saving and Loading Camera Settings Shooting functions Shooting mode + setting, ISO speed, AF mode, AF point, Metering mode, Drive mode, Exposure compensation amount, Flash exposure compensation amount Menu functions [ 1 ] White balance, Custom WB registration, WB SHIFT/BKT , Color space, Picture S tyle, Peripheral illumination correction [ 2 [...]

240 Y ou can set the basic settings of majo r functions such as the shooting mode, AF mode, metering mode, and drive m ode and register them in the camera. This is convenient when you want to instantly switch to frequently-used shooting settings. 1 Select [Regist/apply basic settings]. Under the [ 7 ] tab, select [ Regist/apply basic settings ], th[...]

241 Reference This chapter provides refere nce information for camera features, system accessories, etc. The back of this chapter also has an index to make it easier to look up needed information. C OP Y[...]

242 o : Set automatically k : User selectable : Not selectable/Disabled * S t ill photos will be shot with the color sp ace set. Function Availability Table Function Viewfinder Shooting z LV Shooting k Movie Shooting d s f a Bulb Image size JPEG kkkkk k (S till photo) RAW kkkkk k RAW +JPEG kkkkk k ISO speed Auto kkkkk k k Manual kkkkk k Enabled in [...]

243 Function Availability Table o : Set automatically k : User selectable : Not selectable/Invalid Function Viewfinder Shooting z LV Shooting k Movie Shooting d s f a Bulb AF One-Shot kkkkk With f AI Servo kkkkk AF point selection Auto kkkkk With f Manual kkkkk Live mode k k u Live mode k k Quick mode k Before shooting starts Metering Evaluative k [...]

244 System Map 270EX ST -E2 430EX II 580EX II Macro Ring Lite MR-14EX Macro T win Lite MT -24EX Anti-Fog Eyepiece Eg Eyecup Eg Angle Finder C Dioptric Adjustment Lenses Eg Wide Strap L6 Bundled Accessories Focusing Screen Ec CR2025 lithium battery Battery Pack LP-E4 Battery Charger LC-E4 AC Adapter Kit ACK-E4 Car Battery Cable CB-570 EOS DIGIT AL S[...]

245 System Map Timer Remote Controller TC-80N3 Remote Switch RS-80N3 Wireless Controller LC-5 EF lenses HDMI Cable HTC-100 External microphone Interface Cable IFC-200U Interface Cable IFC-500U Wireless File T ransmitter WFT -E2 II A/B/C/D or WFT -E2/E2A* * WFT -E2/E2A: Firmware V er. 2.0.0 or higher USB external media USB GPS unit TV/Video Wireless[...]

246 With [ 8 C.Fn II -10: INFO. button when shooting ] (p.217) set to [ 1: Displays camera settings ], pressing the < B > button while the camera is ready to shoot will display image-related function settings. Display the camera settings. While the camera is ready to shoot, press the < B > button. * Displayed only if Wireless File T ran[...]

247 Y ou can check the battery’s condition on a menu screen. Select [Battery info.]. Under the [ 6 ] tab, select [ Battery info. ], then press < 0 >. 3 Checking the Battery Information The model of the battery or household power source (sold separately) being used is displayed. Next to the batter y check (p.35), the remaining battery capaci[...]

248 The date/time (back-up) battery’s serv ice life is approx. 5 years. If the date/time is reset when camera is turned on, replace the back-up battery with a new CR2025 lithium battery as described below . The date/time setting will also be reset, so be sure to set the correct date/time (p.49) . 1 Set the power switch to < 2 > and remove t[...]

249 If there is a problem, first refer to this T roubleshooting Guide on pages 249 to 255. If this T roubleshooting Guid e does not resolve the problem, contact your dealer or nearest Canon Service Center . Do not recharge any battery pack ot her than a genuine Canon Battery Pack LP-E4. See pages 30 and 31. The battery is not properly installed in [...]

250 Troubleshooting Guide Auto power off is in ef fect. If y ou do not want auto power off to take effect, set [ 5 Auto power off ] to [ Off ]. The camera cannot be used wi th EF-S lenses (p.39). If a card error message is di splayed, see page 38 or 256. The card is not properly inserted (p.36). If you are using an SD card, set the write-protect sw[...]

251 Troubleshooting Guide Set [ 8 C.Fn II -4: Auto Lighting Optimizer ] to [ 3: Disable ]. If it is set to [ St andard/Low/Strong ], the image might stil l come out bright even if you set a darker exposure with manual exposure, exposure compensation, or flash exposu re compensation (p.81, 215). Set [ 8 C.Fn II -2: High IS O speed noise reduction ] [...]

252 Troubleshooting Guide If you use a flash unit other than an EX-series S peedlite, the flash will always be fired at full output (p.120). When the [ Flash metering mode ] flash Custom Function is set to [ TTL (autoflash) ], the flash will always be fired at full output (p.124). If flash exposure compensation has already been set with the S peedl[...]

253 Troubleshooting Guide Set [ LV z / k set. ] to [ Movies ] and set the shooting mode to < a > (manual exposure) (p.142, 144). If the card’s writing speed is slow , movie shooting may stop automatically . If you use a CF card, use one with a read/write speed of at least 8 MB per sec. If you us e an SD card, use one with SD S peed Class 6 [...]

254 Troubleshooting Guide If you operate the camera’s dial or lens during movie shooting, the respective operation noise will al so be recorded. Using an external microphone (commercially avail able) is recommended (p.153). If the LCD monitor is dirty , use a soft cloth to clean it. In low or high temperatures, the LCD monitor display may seem sl[...]

255 Troubleshooting Guide If you use a card wh ich already has images recorded, the file numbering might start from the la st image in the card (p.88). The correct date and time has not been set (p.49). Make sure the stereo A V cable or HDMI cable’s plug is connected all the way in (p.170, 171). Set the video OUT format (NTSC/P AL) to the same vi[...]

256 If there is a problem with the camera, an error message will appear . Follow the on- screen instructions. * If the error still persists, write down the error No. and cont act your nearest Canon Service Center . Error Codes No. Error Message & Solution 01 Communications between the camera and lens is faulty . Clean the lens contact s. Î Cle[...]

257 •T y p e T ype: Digital, single-lens reflex, AF/AE camera Recording media: CF card (T ype I or II, UDMA-compatible), SD memory card, SDHC memory card * With Wireless File T ransm itter WFT -E2 II A/B/C/D or WFT -E2/E2A (with firmware Ve r . 2.0.0 or higher), recording to USB exte rnal media possible Image sensor size: 27.9 x 18.6 mm Compatibl[...]

258 Specifications • Image Processing Picture S tyle: S tandard, Portrait, Landscape, Neutral, Faithful, Monochrome, User Def. 1 - 3 White balance: Auto, Preset (Dayligh t, Shade, Cloudy , Tungsten light, White fluorescent light, Flash), Custom (total 5 settings), Color temperature setting (250 0-10000K), pe rsonal white balance (total 5 settings[...]

259 Specifications • Exposure Cont rol Metering modes: 63-zone TTL full -aperture metering • Evaluative metering (lin kable to any AF point) • Partial metering (approx. 13.5% of viewfinder at center) • S pot metering (approx. 3.8% of viewfinder at center) • Center-weighted average metering Metering range: EV 0 - 20 (at 23°C/73°F with EF[...]

260 Specifications • External Speedlite Compatible flash: EX-series Speedlite (F unctions settable with the camera) Flash metering: E-TTL II autoflash Flash exposure compensation: ±3 stops in 1/ 3- or 1/2-stop increments FE lock: Provided PC terminal: Provided S tandard flash exposure level adjustment: FE Microadjustment possible • Live View S[...]

261 Specifications ISO speed: During autoexposure shooting: Automatically set During manual ex posure shooting: Auto (ISO Auto), manual se tting within ISO 100 - 12800 (1/3- or whole-stop incremen ts) and expandable to H1 (ISO 25600), H2 (ISO 51 200), H3 (ISO 102400) Sound recording: Built-in monaural microphone External stereo microphone term inal[...]

262 Specifications • Custom Functions Custom Functions: 62 under C.Fn I to IV C.Fn setting registration: Three sets can be registered Save camera settings: Up to ten se ts can be registered in a card Register basic camera settings: Up to nine settings can be set My Menu registration: Up to six options can be registered Copyright information: Entr[...]

263 Specifications • Dimensions and Weight Dimensions (W x H x D) : 156 x 156.6 x 79.9 mm / 6.1 x 6.2 x 3.1 in. Weight: Approx. 1 180 g / 41.6 oz. (body only) • Operation Environment Working temperature range: 0°C - 45°C / 32°F - 1 13°F Working humidity: 85% or less • Battery Pack LP-E4 T ype: Rechargeable lithium ion battery Rated voltag[...]

264 T rademarks Adobe is a trademark of Ad obe Systems Incorporated. Windows is a trademark or registered trademark of Mi crosoft Corporation in the United S tates and other countries. Macintosh and Mac OS is a trademark or registered trademark of Apple Inc. in the United S tates and other countries. CompactFlash is a trademar k of SanDisk Corporat[...]

265 CAUTION RISK OF EXPLOSION IF BA TTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BA TTERIES ACCORDING TO LOCAL REGULA TION. Use of genuine Canon accessories is recommended This product is designed to achieve excellent perf ormance when used with genuine Canon accessories. Canon shall not be liable for any damage to this product and/or ac[...]

266 Safety Warnings Follow these safeguards an d use the equipment properly to prevent injury , death, and material damage. Preventing Serious Injury or Death • T o prevent fire, excessive heat, chemic al leakage, and explosions, follow the safeguards below: - Do not use any batteries, power sources, and accessories not specified in this booklet.[...]

267 • If you drop the equipment and the casing br eaks open to expose the internal parts, do not touch the internal parts due to the possibility of electrical shock. • Do not disassemble or modify the equipment. High-voltage internal parts can cause electrical shock. • Do not look at the sun or an extremely bright light source through the cam[...]

268 Digital Camera Model DS12621 1 Systems This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1 ) This device may not ca use harmful interference, and (2) this device mu st accept any interference received, including interference that may ca use undesired operation. Note: This equipment has be[...]

269 IMPORT ANT SAFETY INSTRUCTIONS 1. SA VE THESE INSTRUCTIONS — This manual contai ns important safety and operating instructions for Battery Charger LC-E4. 2. Before using the charger, read all in structions and cautionary remarks on (1) the charger , (2) the ba ttery pack, and (3) the pro duct using the battery pack. 3. CAUTION — T o reduce [...]

270 Index 10-sec. or 2-sec. delay ................. 102 1280x720 ............... ....................... 151 1920x1080 ............. ....................... 151 1st-curtain sync. ............................ 122 2nd-curtain sync .... ....................... 122 4- or 9-image index display........... 159 640x480 ................. ...................[...]

271 Index Color temperature setting ............... 78 Color tone ................ ............... 68, 196 Compression rate. ................. .......... 63 Continuous ........... ................. ..........88 Continuous shooti ng .....................101 Contrast ................... ...............68, 196 Cool tone (printin g) ...................[...]

272 Index Focusing AF mode ............ ......................... 94 AF point display . ....................... 158 AF point selectio n ....................... 97 AF-assist beam . ....................... 225 Beeper ........................................ 52 Difficult-to-focus subjects .... 100, 135 Live View shooting ........... 131, 138 Manual fo[...]

273 Index LCD monitor ......... ..................... 13, 17 Brightness adjustment .............. 180 Image playback ........................ 156 Menu screen ........ ................. 44, 46 Shooting settings display .... 23, 217 LCD panel ............ ..................... 21, 22 Illumination ...............................116 Lens Attaching/Deta[...]

274 Index NTSC ......................... ........... 151, 170 Number of AF poin ts ..................... 223 O ONE SHOT (One-S hot AF)............. 95 One-Shot AF .......... ......................... 95 P P (Program AE) ..... ....................... 106 P AL ............................ ........... 151, 170 Paper settings (print ing)...............[...]

275 Index 0 button ................. .......................44 Sharpness ............ ................. .......... 68 Shooting information display ...................... ..... 128, 148, 157 Shooting mode ..... ................. .......... 21 Aperture-priority AE .................. 110 Bulb ..................... .....................116 Manual expos[...]

This Instruction Manual booklet is current as of October 2009. For information on the camera’s compatibility with any accessories and lenses introduced after this date, contact any Canon Service Center . CT1-1034-003 © CANON INC. 2010 CANON INC. 30-2, Shimomaruko 3-chome, Ohta-ku, T okyo 146-8501, Japan U.S.A. CANON U.S.A. INC. One Canon Plaza, [...]