Cisco Systems Cisco 12816 Bedienungsanleitung

Y ou'll be entered into a quarterly drawing for free Cisco Press books by returning this su rvey! Cisco is dedicated to customer satisfaction and would like to hear your thoughts on these prin ted manuals. Please visit the Ci sco Product Comments on-line sur vey at www .cisco.com/go/crc to submit your comments about accessing Cisco technical m[...]

BUSINESS REPLY MAIL FIRST-CLASS MAIL PERMIT NO. 4631 SAN JOSE CA POSTAGE WILL BE PAID BY ADDRESSEE NO POST A GE NECESSAR Y IF MAILED IN THE UNITED ST A TES DOCUMENT RESOURCE CONNECTION CISCO SYSTEMS INC 170 WEST TASMAN DR SAN JOSE CA 95134-9916[...]

Corporate Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 526-4100 Cisco 1 20 1 6, Cisco 1 241 6, and Cisco 1 281 6 Router Installation and Conf iguration Guide Text Part Number: O L-11495-01[...]

THE SPECIFICA TION S AND INFORMA T ION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHAN GE WITHOUT NO TI CE. ALL ST A TEMENTS, INFO RMA TION, AND RECOMMENDA TION S IN THIS MANUAL ARE BELIEVED T O BE ACCURA TE BUT ARE PRESENTED WITHOUT W ARRANTY OF ANY KIN D, EXPRESS OR IMPL IED. USERS MU ST T A KE FULL RESPONS IBILITY FOR THEIR APPLICA TIO[...]

xiii Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 About This Guide Audience The Cisco 12016, Cisco 12416, an d Cisco 12816 Router Installation a nd Confi guration Guide is wr itten for hardware instal lers and syste m administrators of Cisco routers. This publication assumes that th e user has a[...]

About This Guide Document Organization xiv Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Document Organization This installation and co nfiguration guide is org anized into the follo wing chapters and appendix es: • Chapter 1, “Product Overvie w , ” provides an introducti on to the major co[...]

xv Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 About This Guide Document Conven tions Document Conventions This publication u ses the following con ventions: • Ctrl represents the key labeled Contr ol . For e xample, the key combination Ctrl-Z means hold do wn the Control k ey while you press[...]

About This Guide Obtaining Documentation xvi Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 T imesaver Means the described action saves time . Y ou can sa ve time b y performing the action described in the paragrap h. War ni n g This warning symbol means danger . Y ou are in a situation that cou l[...]

xvii Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 About This Guide Obtaining Documentation Product Documentation DVD Cisco documentation and additi onal lite rature are av ailable in the Product Documentation D VD package, which may hav e shipped with your prod uct. The Product Documentation D V[...]

About This Guide Documentation Feedba ck xviii Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 • Instructions for o rdering documentation using the Ordering tool are at this URL: http://www .cisco.co m/univ ercd/cc/td/doc/es_inpck/pdi.ht m • Nonregist ered Cisco.com users can order documentatio[...]

xix Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 About This Guide Cisco Product Security O verview A current list of security ad visories and notic es for Cisco products i s av ailable at this URL: http://www .cisco.com/g o/psirt If you prefer to see advisories and notices as they are updated in[...]

About This Guide Obtaining Technical Assistance xx Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 The link on this page has the curr ent PGP key ID in use. Obtaining Technical Assistance Cisco T echnical Support pro vides 24-hour-a-day a ward-winning techni cal assistance. The Cisco T echnical Sup[...]

xxi Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 About This Guide Obtaining Techn ical Assistance Submitting a Service Request Using the online T A C Service Request T ool is the fastest way to open S3 and S4 service requests. (S3 and S4 service request s are those in which your netw ork is mini[...]

About This Guide Obtaining Additional Publ ications and Information xxii Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Se verity 3 (S3)—Operat ional performance of your netw ork is impaired, b ut most busin ess operations remain functional . Y ou and Cisco will commit resources during normal bu[...]

xxiii Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 About This Guide Obtaining Additional Public ations and Information solve t hem, using real-world case studies and b usiness strategies to help readers make sound technology in ves tment decisions. Y ou can access iQ Magazine at this URL: http:/[...]

About This Guide Obtaining Additional Publ ications and Information xxiv Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01[...]

iii Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 CONTENTS About This Guide xiii Audience xiii Purpose xiii Document Organization xiv Document Conventions xv Obtaining Documentation xvi Cisco.com xvi Product Documentation DVD xvii Ordering Documentation xvii Documentation Feedback xviii Cisco Pro[...]

Contents iv Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 AC Power Supplies 1-10 DC Power Shelf 1-12 DC Power Supplies 1-15 Chassis Card Cages 1-17 Upper Card Cage 1-17 Lower Card Cage 1-18 Switch Fabric Card Cage 1-18 Switch Fabric Ov erview 1-19 Switch Fabric Card Functionality 1-19 Clock Sched[...]

v Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Contents PRP Reset Switch 1-37 PRP Alphanumeric Message Displays 1-38 PRP Memory Components 1-39 PRP SDRAM 1-41 PRP SRAM 1-41 PRP NVRAM 1-42 PRP Flash Memory 1-42 Upper and Lower Cable Managemen t Brackets 1-43 Blower Module 1-44 CHAPTER 2 Preparing[...]

Contents vi Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Site Wiring Guidelines 2-24 GRP Port Connection Guidelines 2-25 GRP Auxiliary and Console Port Connection s 2-26 GRP Auxiliary Port Signals 2-27 GRP Console Port Signa ls 2-28 GRP Ethernet Port Connections 2-29 GRP RJ-45 Ethe rnet Connecti[...]

vii Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Contents Connecting to the Front Groun ding Receptacle 3-22 Connecting to the Top Rear Receptacle 3-24 Attaching the Vertical Cab le-Management Trou gh 3-25 Connecting Line Card Ne twork Interface Cables 3-27 Connecting GRP Route Process or Cables[...]

Contents viii Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Booting from the Cisco IOS Software Image 4-12 Configuring the Router 4-14 Cisco IOS User Interface 4-15 Cisco IOS User Interface Com mand Modes 4-15 User EXEC Mode 4-16 Privileged EXEC Mode 4-16 Global Configuration Mode 4-17 Using Setu[...]

ix Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Contents squeeze Command 4-51 Booting from Flash Memory 4-52 Copying Image Files to or From Flash Memory 4-52 Copying a Cisco IOS Software Image into a Flash Memory Ca rd 4-54 Copying Cisco IOS Software Images Between Flash Me mory Cards 4-56 Copyi[...]

Contents x Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Analyzing the Data 5-30 crc16 Output 5-30 Grant Parity and Request Errors 5-33 Properly Seating Switch Fabric Cards 5-35 Troubleshooting the Cooling Subsys tem 5-36 Blower Module Operation 5-38 Power Supply Operation 5-38 Overtemperature Co[...]

xi Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Contents Removing and Installing the Front Co vers and Bezel Extenders on Origina l Cisco 12000 Series Routers 7-3 Removing the Front Covers 7-3 Installing the Front Covers 7-4 Attaching Bezel Extenders to the Front Cover 7-6 Removing and Replacing[...]

Contents xii Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Removing and Replacing Cards from the Chassis 7-79 Removing and Re placing RP and Line Cards from the Upper and Lower Ca rd Cages 7-79 Removing and Replacing an Alarm Card 7-81 Removing and Replacing Switch Fabric Ca rds 7-84 Upgrading th[...]

CH A P T E R 1-1 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 1 Product Overview This chapter p rovides an o vervie w of the Cisco 12016, Cisco 12416, and Cisco 12816 series routers. It contains phy s ical descriptions of the rout er hardware an d major components, as well as functional descri p[...]

Chapter 1 Product Overview Physical and Func tional Description of Router 1-2 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Physical and Functional Description of Router The Cisco 12000 series route r chassis is a sheet-metal enclosure that houses router components. The major components con sist [...]

1-3 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 1 Product Overview Physical and Functional Desc ription of Router Figur e 1 -1 Cisco 120 16 Ser ies Router Compon ents—Fr ont View Switch f abr ic card cage (behind filter door) P W R O K F A U L T T E M P I L I M P W R O K F A U L T T E[...]

Chapter 1 Product Overview Physical and Func tional Description of Router 1-4 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 AC and DC Power Subsystems A router ships with either an A C or DC powered syste m. Source power connects to the power shelf at the back of the chassis which route power to [...]

1-5 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 1 Product Overview Physical and Functional Desc ription of Router Figur e 1 -2 Standard AC-Input P ower Subsyst em —20 0 0 W Caution A router equipped with the standar d AC power subsystem must be operated with three power sup plies inst[...]

Chapter 1 Product Overview Physical and Func tional Description of Router 1-6 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 A C po wer to the router is prov ided through power cord s connected from A C power outlets to connectors on bac k of the po wer shelf as shown in Figure 1-3 . Figur e 1 -3 [...]

1-7 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 1 Product Overview Physical and Functional Desc ription of Router Optional AC Power Shelf The po wer subsystem consists of a double-le vel A C-input po wer shelf with bays for 4 A C-input po wer supplies. Figure 1-4 sho ws the optional po [...]

Chapter 1 Product Overview Physical and Func tional Description of Router 1-8 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Figur e 1 -4 Optional AC- Input Po wer Subsyst em—200 0 W Caution A router equipped wi th the optional A C power su bsystem must be operated with 4 po wer supplies install[...]

1-9 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 1 Product Overview Physical and Functional Desc ription of Router A C po wer to the router is prov ided through power cord s connected from A C power outlets to the connec tors on the back of the power shelf as sho wn in Figure 1-5 . Figur[...]

Chapter 1 Product Overview Physical and Func tional Description of Router 1-10 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 AC Power Supplies Each A C PEM con verts 200 to 240 V A C into -48 VDC, which is distrib uted through the chassis backpl ane to all cards, RPs, and the blower modules. Figu[...]

1-11 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 1 Product Overview Physical and Functional Desc ription of Router Figure 1-7 identifi es the c omponents of a 2500 W A C power supply . Figur e 1 -7 250 0 W AC P ower Supply Co mponents The status LEDs on an A C PEM provide in formation a[...]

Chapter 1 Product Overview Physical and Func tional Description of Router 1-12 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 • ILMI (yello w)—Indicates the PEM is operating in a cu rrent-limiting condition. For additi onal information about troublesh ooting A C PEMs, see the “T roubleshooti[...]

1-13 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 1 Product Overview Physical and Functional Desc ription of Router Figur e 1 -8 DC-Input P ow er Shelf—200 0 Wa t t s Caution A router conf igured for source DC operation must be op erated with 4 DC-input PEMs installed at all times for [...]

Chapter 1 Product Overview Physical and Func tional Description of Router 1-14 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Figur e 1- 9 DC-Input P ower Shelf Connections A1- A1+ A2- A2+ B2+ B2- B1+ B1- Ground B1 Cov er with slotted screw hole; f astens to standoff in middle of cable connection [...]

1-15 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 1 Product Overview Physical and Functional Desc ription of Router DC Power Supplies Each DC PEM operates from a nominal sourc e DC voltage of –48 to –60 VDC and requires a de dicated 60 amp se rvice. Figure 1-10 identif ies the compon[...]

Chapter 1 Product Overview Physical and Func tional Description of Router 1-16 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Figure 1-11 identif ies the components of a 2400 W DC po wer supply . Figur e 1 -1 1 2400 W DC P ower Supply Co mponents The status LEDs on a DC PEM provide information abo[...]

1-17 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 1 Product Overview Chassis Card Cages For additi onal information about troublesh ooting DC PEMs, see the “T roubl eshooting the D C-Input Power Subsystem” sect ion on page 5-1 0 . Chassis Card Cages There are three integral card cage[...]

Chapter 1 Product Overview Chassis Card Cages 1-18 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Lower Card Cage The lower card cage also has eight user -con figurable slots that support additional line cards, an alarm card, and an optional, redundant RP . Note The lower card cage is an in verted[...]

1-19 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 1 Product Overview Switch Fabric Overview Switch Fabric Overview The switch fabric provides synchronized gigabit-speed connections between line cards and the RP . The switch fabric card cage is located behind th e air filter door and cons[...]

Chapter 1 Product Overview Switch Fabric Overview 1-20 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 The router also ships with a blank switch fabric card installed in the far left (non-working ) slot of the switch f abric card cage. The blank f iller panel balances the air flo w through the swit[...]

1-21 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 1 Product Overview Alarm Card, Line Card, and Rout Proc essor Overview Alarm Card, Line Card, and Rout Processor Overview This section p rovides general in formatio n about alarm cards , line cards and ty pes of route processors in stalle[...]

Chapter 1 Product Overview Alarm Card, Line Car d, and Rout Processor Overview 1-22 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Some of the functi ons that the alarm cards provide are: • Supplies +5 VDC to th e MBus modules on router components (see AC a n d DC Po wer Subsystems, page 1-4 ). [...]

1-23 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 1 Product Overview Alarm Card, Line Card, and Rout Proc essor Overview Figur e 1- 12 Alar m Card Components and LEDs Line Cards Up to 15 Cisco 12000 series line cards ca n be installed in the router s upper and lo wer card cages to suppor[...]

Chapter 1 Product Overview Alarm Card, Line Car d, and Rout Processor Overview 1-24 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Route Processor Selection T wo types of RPs are av ailable: a Gigabit Route Processor (GRP) or a Performance Route Processor (PRP). The GR P is the route processor tha[...]

1-25 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 1 Product Overview Alarm Card, Line Card, and Rout Proc essor Overview Figur e 1- 13 Gigabit Route Pr ocessor F ront P anel GRP PCMCIA Card Slot s and Status LEDs T wo PCMCIA card slots (slot 0 and sl ot 1) provide the GRP with addi tiona[...]

Chapter 1 Product Overview Alarm Card, Line Car d, and Rout Processor Overview 1-26 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Figur e 1 -14 Slot Activity LEDs—Fr ont P anel 129254 SLO T -0 SLO T -1 RESET AU X EJECT[...]

1-27 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 1 Product Overview Alarm Card, Line Card, and Rout Proc essor Overview GRP Reset Switch Access to th e (soft) reset switch is through a sma ll opening in the GRP fr ont pane l. T o press the switch, insert a paper clip or similar smal l p[...]

Chapter 1 Product Overview Alarm Card, Line Car d, and Rout Processor Overview 1-28 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 GRP Auxiliary and Console Ports The auxiliary and consol e ports on the GRP are EIA/TIA-232 (also known as RS-232) asynchronous serial ports. Thes e ports connect exte[...]

1-29 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 1 Product Overview Alarm Card, Line Card, and Rout Proc essor Overview The transmission speed of the Ethernet port is not user-conf igurable. Y ou set the speed through an auto sensing scheme on the GRP which is determined by t he network[...]

Chapter 1 Product Overview Alarm Card, Line Car d, and Rout Processor Overview 1-30 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 GRP Alphanumeric Message Displays The alphanumeric message displays are or ganized in two r ows of four LED characters ( Figure 1-16 ). Figur e 1 -16 Alphanumeric Mess[...]

1-31 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 1 Product Overview Alarm Card, Line Card, and Rout Proc essor Overview GRP Memory Components This section describes v arious types of memory used on the GRP to support router functions. Ta b l e 1-1 provides a quick reference of the diffe[...]

Chapter 1 Product Overview Alarm Card, Line Car d, and Rout Processor Overview 1-32 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Figur e 1 -17 GRP Memory Locations S LO T -0 GIGABIT ROUTE PROCESSOR S LO T -1 C O LL LIN K TX R X R J-45 M II R E S E T AUX E JE C T 129255 Bank 2 DRAM DIMMs Bank 1 P[...]

1-33 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 1 Product Overview Alarm Card, Line Card, and Rout Proc essor Overview GRP DRAM The GRP uses Extended Data-Out (EDO) Dynamic Random A ccess Memory (DRAM) to stor e routing tables, protocols, netw ork accounting applications, and to run Ci[...]

Chapter 1 Product Overview Alarm Card, Line Car d, and Rout Processor Overview 1-34 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 GRP Flash Memory Use flash memory to sto re multiple Cisco IOS software and micr ocode images that you can use to operate the router . Y ou can dow nload new images to[...]

1-35 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 1 Product Overview Alarm Card, Line Card, and Rout Proc essor Overview PRP PCMCIA Card Slots and Status LEDs T wo PCMCIA card slots (slot 0 and slot 1) pro vide the PRP wi th additional flash memory capacity . All combinations of dif fere[...]

Chapter 1 Product Overview Alarm Card, Line Car d, and Rout Processor Overview 1-36 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 The follo wing LEDs on the front panel in di cate traffic status and port selection ( Figure 1-19 ): • LINK, EN, TX, RX—Indicat e link activit y (LINK), port enabl[...]

1-37 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 1 Product Overview Alarm Card, Line Card, and Rout Proc essor Overview PRP Reset Switch Access to the (soft) reset switch is throug h a small open ing in the PRP front panel (see Figure 1-18 ). T o press the switch, insert a paper clip or[...]

Chapter 1 Product Overview Alarm Card, Line Car d, and Rout Processor Overview 1-38 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 PRP Alphanumeric Message Displays The alphanumeric message displays are or ganized in two r ows of four LED characters each ( Figure 1-20 ). Figur e 1 -20 Alphanume r [...]

1-39 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 1 Product Overview Alarm Card, Line Card, and Rout Proc essor Overview PRP Memory Components This section describes v arious types of memory used on the PRP to support rout er functions. Ta b l e 1-3 provides a quick reference of the diff[...]

Chapter 1 Product Overview Alarm Card, Line Car d, and Rout Processor Overview 1-40 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Figur e 1 -21 PRP Memory Location s EJE C T RX TX P R IM A R Y SLOT -1 SLOT -0 LINK EN RX TX ETH 1 ETH 0 AUX CONSOLE PERFORMANCE ROUTE PROCESSOR 1 (PRP-1) LINK P R IM [...]

1-41 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 1 Product Overview Alarm Card, Line Card, and Rout Proc essor Overview PRP SDRAM The PRP uses Error Checking and Correction (ECC) Synchronized Dynamic Random Access Memory (SDRAM) to store routi ng tables, protocols, network accounting ap[...]

Chapter 1 Product Overview Alarm Card, Line Car d, and Rout Processor Overview 1-42 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 PRP NVRAM Non-v olatile Random Access Memory (NVRAM) provides 2 MB of memory for system conf iguration files, soft ware register set tings, and en vironmental monitori[...]

1-43 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 1 Product Overview Alarm Card, Line Card, and Rout Proc essor Overview Upper and Lower Cable Management Brackets Cisco 12010, Cisco 12410, and Cisco 1 2810 series routers include upper and lo wer cable management brackets that work toget [...]

Chapter 1 Product Overview Blower Module 1-44 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Blower Module The router has two blo wer modules to distri b ute air within the c hassis. One blower module is located above the upper card cage ; the second blower module is located below the lo wer card [...]

1-45 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 1 Product Overview Blower Module Figur e 1- 2 3 C o o l i n g A i r F l o w T o ensure that there i s adequate air flow to pre vent o verheating inside t he card cages keep the front and back of the rout er unobstru cted. W e recommend at[...]

Chapter 1 Product Overview Blower Module 1-46 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Caution Y ou should inspect and clean the air filter one time per month (mor e often in dusty en vironments). Do not operate the rout er without an air fil ter installed. The blower module controll er card[...]

CH A P T E R 2-1 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 2 Preparing for Installation Before installing your router , consider po wer and cabling requir ements that must be in place at y our instal lation site , sp ecial equipment for installing the router , and the en vironmental condition[...]

Chapter 2 Preparing for Installation Safety Guidelines 2-2 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Safety Guidelines Before you perform an y procedure in this publicat ion, revie w the safety guidelines in this secti on to av oid injuring yourself or damaging the equipment . In addition, be[...]

2-3 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 2 Preparing for Installation Safety Guidelines Safety with Electricity • The installation shall be in comp liance with national and local electrical codes: in the United States, National Fire Protection Association (NFP A) 70, United Sta[...]

Chapter 2 Preparing for Installation Safety Guidelines 2-4 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Preventing Electrostatic Discharge Damage Many ro uter components can be damaged b y static electricity . Not ex ercising the proper electrostatic dischar ge (ESD) precautions can result in in[...]

2-5 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 2 Preparing for Installation Safety Guidelines Figur e 2 -1 Connecting an ESD-Prev entive Strap to the Rout er Chassis ALARM ENABLED FAIL ACO/LT ALARM CSC 0 FAIL 1 0 1 2 ENABLED CRITICAL MAJOR MINOR SFC A C T I V E 0 C A R R I E R R X P K [...]

Chapter 2 Preparing for Installation Safety Guidelines 2-6 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Lifting Guidelines A fully conf igured router can weigh as much as 275 pounds (lb) (124.74 kilogra ms (kg)), while an empty chassis weighs 125 lb ( 56.7 kg). These systems are not intended to [...]

2-7 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 2 Preparing for Installation Site Requirement Gu idelines Laser Safety Some line cards are equipped wit h ports that can emit hazardous laser radiation from the apert ure when there is no cabl e connected to the po rt. This in visible radi[...]

Chapter 2 Preparing for Installation Site Requirement Guidelines 2-8 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Figur e 2-2 Equipment Rack T ypes Enclosed Rack Figure 2-2 a sho ws a free-standing, encl osed rack with two mounting posts in the front. The router shoul d no t be installed in this[...]

2-9 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 2 Preparing for Installation Site Requirement Gu idelines Telco Rack Figure 2-2 c sho ws a telco-type rack. The telco-type rack is an open frame consisting of tw o posts tied together by a cross-bar at the top and a floor stan d at the bot[...]

Chapter 2 Preparing for Installation Site Requirement Guidelines 2-10 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Figur e 2-3 Fr ont-Mounted and C enter -Mounted Installation i n a T elco Rack 27958 F ront-mounted chassis in telco rac k Center-mounted chassis in telco rac k F ront-mount rail Ci[...]

2-11 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 2 Preparing for Installation Site Requirement Gu idelines Site Layout and Equipment Dimensions T o help maintain trouble-free operation, adhere to th e follo wing precautions when planning your rack installation: • Ensure the site of th[...]

Chapter 2 Preparing for Installation Site Requirement Guidelines 2-12 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 • Install the cable-management brackets incl uded with the router to keep cables organized. Be sure to: – Use appropriate strain-relief met hods to protect cables and equipment [...]

2-13 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 2 Preparing for Installation Site Requirement Gu idelines Figur e 2 -4 Router Chassis Footpr int and D imensions—T op View) 17.3 in. 18.75 in. Plastic front cov er 2 in. 2.75 in. 20 in. F ront Back V er tical rac k-mounting flange (each[...]

Chapter 2 Preparing for Installation Site Requirement Guidelines 2-14 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Figure 2-5 sho ws the footprint and outer dimensions of the enhanced version of router chassis. Figur e 2-5 Enhanced Router Ch assis Footpr int and Dimensions—T op View 25.694 in.[...]

2-15 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 2 Preparing for Installation Site Requirement Gu idelines Air Flow Guidelines Cool air is circulated through the rout er chassis by two blo wer modules. The blow er modules maintain acceptable ope rating temper atures for the internal com[...]

Chapter 2 Preparing for Installation Site Requirement Guidelines 2-16 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Figur e 2-6 Air Flow P ath through the Rout er - Side View 26204 Air e xhaust Upper card cage Room air Bottom blo wer module Air filter Air e xhaust P ower supply shelf Middle card [...]

2-17 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 2 Preparing for Installation Site Requirement Gu idelines Temperature and Humidity Guidelines The operating and nonoperating en vironmen tal site requirements are listed in Ta b l e A-4 on page A-4 . The router normal ly operates within t[...]

Chapter 2 Preparing for Installation Site Requirement Guidelines 2-18 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 AC-Powered Routers A C PEMs operate in the nominal range of 200 VA C t o 2 4 0 V A C and require a minimum service of: • 20 A for operation in North America • 16 A for internati[...]

2-19 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 2 Preparing for Installation Site Requirement Gu idelines Ta b l e 2-1 lists po wer cord options. All A C-input power suppl y power cords measure 14 feet (4.3 m). DC-Powered Routers Connections t o DC PEMs are ra ted at 60 am ps maximum. [...]

Chapter 2 Preparing for Installation Site Requirement Guidelines 2-20 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Y ou must terminate DC power cables usin g cable lugs at the power shelf end. Ensure the lugs are dual-hole and that they are able to fit over M6 terminal studs at 0.625-inch (15.88[...]

2-21 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 2 Preparing for Installation Site Requirement Gu idelines Figur e 2-9 T ypical Sour ce DC Po wer Cabling Sc heme for P ow er Shelf Bay B1 27963 Ground – + Ground – + Rectifiers AC Batteries Central office ground CO ground Plant contro[...]

Chapter 2 Preparing for Installation Site Requirement Guidelines 2-22 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Caution DC PEMs contains circuitry to trip the breaker on the PEM if the PEM detects a re verse polarity condition . No damage should occur from re verse polarity , but you should c[...]

2-23 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 2 Preparing for Installation Site Requirement Gu idelines Figur e 2-1 0 Rout er Bonding and Groundin g Receptacles—T o p Rear Figur e 2 -1 1 Router Bonding and G rounding Receptacles—Fr ont 29183 Supplemental bonding and grounding rec[...]

Chapter 2 Preparing for Installation Site Requirement Guidelines 2-24 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 T o ensure a satisfactory supplemental ground connection to the ro uter , use the follo wing parts: Note These parts are not av ailable from Cisc o, but are a vailabl e from commerc[...]

2-25 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 2 Preparing for Installation GRP Port Connectio n Guidelines Site wiring is unlikel y to emit radio inte rference if you use twisted-pair cab le with a good distrib ution of grounding cond uctors. Use a high-quality twisted-pair cable wit[...]

Chapter 2 Preparing for Installation GRP Port Connection Guidelines 2-26 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 GRP Auxiliary and Console Port Connections The GRP has two EIA/TIA-232 ports ( Figure 2-12 ): • Auxiliary port— DB-2 5 plug, DTE-mode port for connecting a modem or other DCE[...]

2-27 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 2 Preparing for Installation GRP Port Connectio n Guidelines Caution T o maintain Class B EMI compliance, you must use shielded cables when connecting to the auxiliar y and console ports of origi nal GRPs (part numbers GRP= and GRP-B=). A[...]

Chapter 2 Preparing for Installation GRP Port Connection Guidelines 2-28 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 GRP Console Port Signals The GRP console port is a DB-25 DCE in terface for connecting a DTE terminal de vice to the router . Both Data Set Ready (DSR) and Data Carrier Detect (D[...]

2-29 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 2 Preparing for Installation GRP Port Connectio n Guidelines GRP Ethernet Port Connections The GRP has the follo wing two ty pes of Ethernet connections ( Figure 2-13 ): • RJ-45 media-dependent interface (MDI) • 40-pin, D-shell type m[...]

Chapter 2 Preparing for Installation GRP Port Connection Guidelines 2-30 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 The GRP Ethernet port does not pr ovide extern al routing functions. Its primary roles are to act as a T elnet port into the router , and to boot or access Cisco IOS software ima[...]

2-31 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 2 Preparing for Installation GRP Port Connectio n Guidelines GRP RJ-45 Ethernet Connections The RJ-45 Ethernet connecti on does not require an external tran sceive r . Figure 2-15 sho ws the pin orientation of the RJ-45 Ethernet po rt and[...]

Chapter 2 Preparing for Installation GRP Port Connection Guidelines 2-32 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 When connecting the RJ-45 por t to a hub or repeater , use the straight-through cable pinout sho wn in Figure 2-16 . Figur e 2-16 Straight-Th rough Ether net Cable Pi nout When c[...]

2-33 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 2 Preparing for Installation GRP Port Connectio n Guidelines GRP MII Ethernet Connections The GRP MII Ethernet connection requires an external physical sublayer (PHY) and an external transceiv er that perm its connection to multimo de fib[...]

Chapter 2 Preparing for Installation GRP Port Connection Guidelines 2-34 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Ta b l e 2-5 lists the signals used on the MII connector . Ta b l e 2-5 GRP M II Ethernet Pinout Pin 1 1. Pins not listed in the table are not used. In Out Input/ Output Descript[...]

2-35 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 2 Preparing for Installation GRP Port Connectio n Guidelines Ta b l e 2-6 lists the cabling specif ications for 100-Mbps tran smission over unshielded twisted-pair (UTP) cables. Ta b l e 2-7 lists IEEE 802.3u physical characteristi cs for[...]

Chapter 2 Preparing for Installation PRP Port Connection Guidelines 2-36 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 PRP Port Connection Guidelines This section contains detailed cabling an d signal information for all interface and port connections to the PRP . It also pro v ides information f[...]

2-37 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 2 Preparing for Installation PRP Port Connectio n Guidelines Figur e 2-19 PRP A uxiliary and Console P ort Connect ions 1 Modem 4 Auxiliary p ort 2 Console terminal 5 Console port 3 RJ-45 cables 70692 R X T X PRIMARY S L O T -1 S L O T -0[...]

Chapter 2 Preparing for Installation PRP Port Connection Guidelines 2-38 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 PRP Auxiliary Port Signals The PRP auxiliary port is a DTE, RJ-45 int erface for connecting a modem or other DCE de vice (such as a CSU/DSU or another rout er) to the PRP . The a[...]

2-39 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 2 Preparing for Installation PRP Port Connectio n Guidelines PRP Console Port Signals The PRP console port is a DCE RJ-45 interf ac e for connecting a terminal to the router . The console port does not support modem control or hardware fl[...]

Chapter 2 Preparing for Installation PRP Port Connection Guidelines 2-40 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 PRP Ethernet Connections The PRP has two RJ-45 MDI Ethe rnet ports; ETH0 and ETH1 ( Figure 2-20 ). Figur e 2-20 PRP Ethernet Connections These connections support IEEE 802.3 and [...]

2-41 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 2 Preparing for Installation PRP Port Connectio n Guidelines Figure 2-21 sho ws: • Y ou cannot access Netw ork 2.0.0.0 from Ethernet port (E0) on th e GRP in Router A. Y ou can only acce ss Host A, Host B, and Router C, which are in Net[...]

Chapter 2 Preparing for Installation PRP Port Connection Guidelines 2-42 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 PRP RJ-45 Ethernet Connections The RJ-45 Ethernet connecti on does not require an external tran sceive r . Figure 2-22 sho ws the pin orientation of the RJ-45 Ethernet po rt and [...]

2-43 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 2 Preparing for Installation PRP Port Connectio n Guidelines When connecting the RJ-45 por t to a hub or repeater , use the straight-through cable pinout sho wn in Figure 2-23 . Figur e 2-23 Straight-Thr ough Cable Pinout t o Hub or Repea[...]

Chapter 2 Preparing for Installation PRP Port Connection Guidelines 2-44 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Ta b l e 2-11 lists the cabling sp ecifications for 100-Mbps transmissi on over unshielded twisted-pair (UTP) cables. Note The transmission speed of the Ethernet port s is autose[...]

2-45 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 2 Preparing for Installation Alarm Card Connection Gu idelines Alarm Card Connection Guidelines The router is eq uipped with two alar m cards: • One alarm ca rd occupies the dedi cated far left slot in the upper card cage • The second[...]

Chapter 2 Preparing for Installation Alarm Card Connection Gu idelines 2-46 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Note T o comply with the intrab uilding lightn ing surge requirements of GR-1089-CORE, Issue II, Revision 01, February 1999, you must use a sh ielded cable when connecting to [...]

CH A P T E R 3-1 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 3 Installing the Router This chapter contains the proc edures to install the ro uter in a rack. The installation is presented in the f ollowing secti ons: • Pre-Installation Consid erations and Requirements, page 3-2 • Rack-Mounti[...]

Chapter 3 Insta lling the Router Pre-Installation Considerations and Requir ements 3-2 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Pre-Installation Considerations and Requirements Before you perform an y procedures in this chapter , revie w the follo wing sections in Chapter 2, “Preparing for[...]

3-3 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 3 Installing the Router Pre-Installation Consider ations and Requirements Required Tools and Equipment Before you be gin the rack-mount installation, you must r ead and understand the informatio n in the “Rack-Mounting Guidelines” sect[...]

Chapter 3 Insta lling the Router Pre-Installation Considerations and Requir ements 3-4 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Removing the Front Covers from Cisco 12016 Original Series Routers The chassis front cov ers for the power sh elf and upper blo wer module, upper card cage, lo wer [...]

3-5 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 3 Installing the Router Pre-Installation Consider ations and Requirements Figur e 3-1 Router Chassis F ront Cov ers 1 Ball stud 2 Ball stud clip P W R O K F A U L T T E M P I L I M P W R O K F A U L T T E M P I L I M P W R O K F A U L T T [...]

Chapter 3 Insta lling the Router Pre-Installation Considerations and Requir ements 3-6 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Removing the Front Cover from Cisco 12016 Enhanced Series Routers The ne w cover on the Cisco enha nced series of routers has a two-piece front co ver . The cov ers[...]

3-7 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 3 Installing the Router Pre-Installation Consider ations and Requirements Figur e 3- 2 Removing the F ront Co vers 1 Release bu ttons P W R O K F A U L T T E M P I L I M P W R O K F A U L T T E M P I L I M P W R O K F A U L T T E M P I L I[...]

Chapter 3 Insta lling the Router Rack-Mounting the Router Chassis 3-8 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Rack-Mounting the Router Chassis The router chassis can be installed in either a front-mounted position or a center-mou nted position. • In a front-mount ed position, the chassis [...]

3-9 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 3 Installing the Router Rack-Mounting the Ro uter Chassis Figur e 3-3 V erifying Equipment Rack Dimensions Installing Center-Mount Brackets—Optional If you plan to install the router in the center-mount po sition, you must install the ce[...]

Chapter 3 Insta lling the Router Rack-Mounting the Router Chassis 3-10 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Step 1 Determine the location in which you w ant to position the chassi s in the rack, and mark holes at the same height on both the left and right rack rails. Step 2 Identify th e[...]

3-11 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 3 Installing the Router Rack-Mounting the Ro uter Chassis b. Finger -tighten a second scre w in the top hole of the bracket. c. Finger -tighten three more scre ws in the middle of in the bracket. d. Use a screwdri ver to tighten all f ive[...]

Chapter 3 Insta lling the Router Rack-Mounting the Router Chassis 3-12 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Figur e 3-5 Installing a Center -Mount Rac k-Mounting Br ack et 28450 Rack Chassis Chassis rac k-mounting rail Brac ket Brac ket Open hole (screw inserted through) Threaded hole (c[...]

3-13 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 3 Installing the Router Rack-Mounting the Ro uter Chassis Installing the Chassis Rack-Mounting Platform The rack-mounting platfor m is installed at the bottom of an empty rack and acts as a permanent support platform fo r the chassis. It [...]

Chapter 3 Insta lling the Router Rack-Mounting the Router Chassis 3-14 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Repeat these steps to attach a bracket in the same position on the other side of the platform. Step 4 Align the platf orm between the rack posts and set it in position so that the [...]

3-15 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 3 Installing the Router Rack-Mounting the Ro uter Chassis Unpack and Position the Router Unpack the router followin g the instructions in the Cisco 12016, Cisco 12416, and Cisco 12816 Router Unpac king Instructions th at came with the rou[...]

Chapter 3 Insta lling the Router Rack-Mounting the Router Chassis 3-16 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Installing the Chassis into the Rack Use the foll owing procedure to ins tall the cha ssis in the r ack. Step 1 Rotate the scissor -jack scre w counterclockwise slowly and expand t[...]

3-17 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 3 Installing the Router Rack-Mounting the Ro uter Chassis Step 2 Remov e the four bolts and chassis anchor c lips that secure the bas e of the chassis to the scissor-jack platform ( Figure 3-9 ). Figur e 3-9 Removing the Chassis Anchor Cl[...]

Chapter 3 Insta lling the Router Rack-Mounting the Router Chassis 3-18 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Step 3 Grasp the handle on the back pa nel of th e chassis to carefully pull the chassis off of the sci ssor-jack platform and onto t he rack-mounting plat form while a second pers[...]

3-19 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 3 Installing the Router Rack-Mounting the Ro uter Chassis Step 4 Insert the chassis in to the rack until the chassis rack-mounting flanges ar e flush against the mounting flanges on the rack (or the optional center-mount brackets, if inst[...]

Chapter 3 Insta lling the Router Rack-Mounting the Router Chassis 3-20 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Figur e 3-1 1 Ch assis Rack-Mou nting Hole Gro ups 26864 Chassis mounting holes group E Chassis mounting holes group D Chassis mounting holes group C Chassis mounting holes group B[...]

3-21 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 3 Installing the Router Supplemental Bonding and Grounding Conne ctions Supplemental Bonding and Grounding Connections Before you conn ect power to t he router , or power on the router for the first time, we recommend that you connect the[...]

Chapter 3 Insta lling the Router Supplemental Bond ing and Grounding Connections 3-22 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Connecting to the Front Grounding Receptacle Use the follo wing procedure to connect the supplemental groun ding cable to front grounding receptacle. Step 1 Loosen t[...]

3-23 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 3 Installing the Router Supplemental Bonding and Grounding Conne ctions Step 2 Attach the grounding ca ble to the chass is ( Figure 3-13 ): a. Insert two M6 bolts through the grounding holes in the chassis. b. Place the cable lug o ver th[...]

Chapter 3 Insta lling the Router Supplemental Bond ing and Grounding Connections 3-24 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Connecting to the Top Rear Receptacle Use the following procedure to connect the supplemental grounding ca ble to to p rear grounding receptacle. Step 1 Attach the g[...]

3-25 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 3 Installing the Router Attaching the Vertical Cable-Ma nagement Trough Attaching the Vertical Cable-Management Trough Refer to Figure 3-15 and use the follo wing proced ure to attach the v ertical cable-management trough. Step 1 Position[...]

Chapter 3 Insta lling the Router Attaching the Vertic al Cable-Manag ement Trough 3-26 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Figur e 3- 15 At taching the V e rtical Cable-Manag ement T roughs P W R O K F A U L T T E M P I L I M P W R O K F A U L T T E M P I L I M P W R O K F A U L T T E M[...]

3-27 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 3 Installing the Router Connecting Line Card Network Inte rface Cables Connecting Line Card Network Interface Cables This section descri bes how to route the n etwork interface cab les through the router cable-management syst em and a tta[...]

Chapter 3 Insta lling the Router Connecting Line Card Network Interface Cables 3-28 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Step 5 Repeat Steps 3 thro ugh 5 for each additional cable connection to that line card. Figur e 3- 16 Connecting a Networ k Interf ace Cable to a Legac y Line Card F [...]

3-29 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 3 Installing the Router Connecting Line Card Network Inte rface Cables Step 6 Insert all cables into their assigned ports. Step 7 Place sev eral ev enly space d velcro straps through slots on the cabl e-management bracket ( Figure 3-17 a)[...]

Chapter 3 Insta lling the Router Connecting Line Card Network Interface Cables 3-30 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Figur e 3-17 Curr ent Style Cable Manag e ment Brac ket ACTIVE 0 CARRIER RX PKT ACTIVE 1 CARRIER RX PKT ACTIVE 2 CARRIER RX PKT ACTIVE 3 CARRIER RX PKT Q OC-3/STM-POS [...]

3-31 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 3 Installing the Router Connecting GRP Route Pro cessor Cables Connecting GRP Route Processor Cables This section descri bes how to connect cabl es to the console, auxiliary , and Ethernet ports on the GRP . The console and auxiliary port[...]

Chapter 3 Insta lling the Router Connecting GRP Route Processor Cables 3-32 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Note T o comply with T elcordia GR-1089 NEBS standard for electromagnetic compatib ility and sa fety , connect all cons ole, auxiliary , and Ethernet interfaces only to intrab[...]

3-33 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 3 Installing the Router Connecting GRP Route Pro cessor Cables Connecting to the GRP Auxiliary Port The auxiliary port on the GRP is an EIA/TI A-232 DTE DB-25 plug for connecting a modem or other DCE de vice (such as a channel service uni[...]

Chapter 3 Insta lling the Router Connecting GRP Route Processor Cables 3-34 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 LEDs on the fro nt panel in dicate whic h Ethernet r eceptacle is activ e when the GRP is operating. See “GRP Ethernet Port Connection s” section on page 2-29 for addition[...]

3-35 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 3 Installing the Router Connecting GRP Route Pro cessor Cables RJ-45 Connection Use the following procedure to connect an Ethernet cabl e to the RJ-45 receptacle. Step 1 Plug the cable directly in to the RJ-45 receptacle. Step 2 Connect t[...]

Chapter 3 Insta lling the Router Connecting PRP Route Processor Cables 3-36 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Connecting PRP Route Processor Cables This section descri bes how to connect cabl es to the console, auxiliary , and Ethernet ports on the PRP . The console and auxiliary port[...]

3-37 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 3 Installing the Router Connecting PRP Route Processor Cables Note RP cables are not av ailable from Cisco, but are av ailable from any commercial cable vendor . Note T o comply with T elcordia GR-1089 NEBS standard for electromagnetic co[...]

Chapter 3 Insta lling the Router Connecting PRP Route Processor Cables 3-38 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Connecting to the PRP Auxiliary Port The auxiliary port on the PRP is a DTE, RJ-45 receptacle for connecting a modem or other DCE device (such as a CSU/DSU or anoth er router)[...]

3-39 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 3 Installing the Router Connecting PRP Route Processor Cables Note RJ-45 cables a re not av ailable from C i sco System s; they are a vailable from outside commercial cable vendors. Use ca bles that comply with EIA/TIA-568 standards. Caut[...]

Chapter 3 Insta lling the Router Connecting an Alar m Card Cable 3-40 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Connecting an Alarm Card Cable Each router alarm card has one 25-pin Dsub connector , labeled Alarm ( Figure 3-21 ). Figur e 3-21 Alar m Card Cable Connection Alarm subconnectors ca[...]

3-41 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 3 Installing the Router Connecting Power to the Power Shelf Caution Only safety extra-lo w voltage (SEL V) ci rcuits can be connected to the alarm connector . Maximum rating for the alarm circuit is 2 A, 50 VA . Note T o comply with T elc[...]

Chapter 3 Insta lling the Router Connecting Power to the Power Shelf 3-42 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Step 1 Connect each A C power cord to the back pa nel of the power shelf and secure them in place wit h their re tention cl ips ( Figure 3-22 ). Figur e 3-22 Connecting AC P owe[...]

3-43 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 3 Installing the Router Connecting Power to the Power Shelf Because there is no color co de standard for source DC wiring, you must be sure that po wer source cables are connected to the power shelf with the proper positive (+) and ne gat[...]

Chapter 3 Insta lling the Router Connecting Power to the Power Shelf 3-44 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Figur e 3-23 DC-Input T erminal Conn ections on the DC-Input P o wer Shelf A1- A1+ A2- A2+ B2+ B2- B1+ B1- Ground B1 Cov er with slotted screw hole; f astens to standoff in midd[...]

3-45 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 3 Installing the Router Connecting Power to the Power Shelf Step 2 Connect the g round and each pair of po wer cables to the DC-inp ut terminal studs as follo ws ( Figure 3-24 ): War ni n g When reconnecting source DC power cables, alway [...]

Chapter 3 Insta lling the Router Connecting Power to the Power Shelf 3-46 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Step 3 Reinsta ll the po wer cable co ver ( Figure 3-25 ). Figur e 3-25 Reinstalling the Source DC P ow er Cable Cov e r 27219 Ground – + Cov er standoff Cov er with slotted s[...]

3-47 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 3 Installing the Router Installing the Front Covers of Ci sco 12016 Original Series Routers Installing the Front Covers of Cisco 12016 Original Series Routers The chassis front cov ers for the power sh elf and upper blo wer module, upper [...]

Chapter 3 Insta lling the Router Installing the Front Co vers of Cisco 12016 Original Series Routers 3-48 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Figur e 3-26 Router Chassis Fr ont Cov ers P W R O K F A U L T T E M P I L I M P W R O K F A U L T T E M P I L I M P W R O K F A U L T T E M P I [...]

3-49 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 3 Installing the Router Installing the Front Cover of Cisco 12010 Enhanced Series Routers Installing the Front Cover of Cisco 12010 Enhanced Series Routers Refer to Figure 3-27 and use the following procedure to inst all the fron t cover [...]

Chapter 3 Insta lling the Router Installing the Front Co ver of Cisco 12010 Enhanced S eries Routers 3-50 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Figur e 3-27 At taching t he Fr ont Cov ers 1 Release bu ttons P W R O K F A U L T T E M P I L I M P W R O K F A U L T T E M P I L I M P W R O K [...]

3-51 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 3 Installing the Router Installing the Front Cover of Cisco 12010 Enhanced Series Routers This completes the hardw are installation procedures for Cisco 12016, Cisco 12416, and Cisco 12816 routers. Proceed to the ne xt chapter to perform [...]

Chapter 3 Insta lling the Router Installing the Front Co ver of Cisco 12010 Enhanced S eries Routers 3-52 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01[...]

CH A P T E R 4-1 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 4 System Startup and Basic Configuration The system startup pro cess and a procedure for performing a basic conf iguration of your Cisco 12016, Cisco 12416, or Cisco 12816 router is presented in th e follo wing sections: • Sources o[...]

Chapter 4 System Sta rtup and Basic Configuration Sources of Cisco IOS Softwar e 4-2 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 This chapter pro vides you with the info rmation to configure yo ur system so that it can access the network or enable ot her hosts in the network to access your syst[...]

4-3 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 4 System Startup and Basic Configuration Boot Pr ocess Overview • A terminal de vice is connected to the console port on the RP , powered on, and config ured for 9600 bps, 8 data bits, no parity , and 2 stop bits (9600, 8N2). Note Y ou m[...]

Chapter 4 System Sta rtup and Basic Configuration Powering On the Router and Obser ving the Boot Process 4-4 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 7. When the Cisco IOS softw are boots, it polls all other cards in t he system, powers them on, and loads the Ci sco IOS softw are they requir[...]

4-5 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 4 System Startup and Basic Configuration Powering On the Router and Observing the Boot Process Step 4 Observe t he RP alphanumeric LED displays during the RP boot process ( Figure 4-1 ). Figur e 4-1 RP Alphanum er ic LED Displays Each 4-di[...]

Chapter 4 System Sta rtup and Basic Configuration Powering On the Router and Obser ving the Boot Process 4-6 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Step 5 Observe the status of the RP interfaces (see Figure 4-2 for the GRP and Figure 4-3 for the PRP). The LEDs on the RP show system status,[...]

4-7 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 4 System Startup and Basic Configuration Powering On the Router and Observing the Boot Process Figur e 4-2 GRP LEDs—Par tial Fr ont P anel View Figur e 4-3 PRP Ether net P orts and LEDs—P artial Fr ont P anel View H10762 SLO T -0 SLO T[...]

Chapter 4 System Sta rtup and Basic Configuration Powering On the Router and Obser ving the Boot Process 4-8 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Step 6 During the line card boo t process, observe the alphanumeric LED displ ays on each line card ( Figure 4-4 ). Note The line card boot pr[...]

4-9 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 4 System Startup and Basic Configuration Powering On the Router and Observing the Boot Process RO M I GET The R OM image is being lo aded into line card memory . RP Cisco IOS software FA B L WA I T The line card is waiti ng for the fabric [...]

Chapter 4 System Sta rtup and Basic Configuration Powering On the Router and Obser ving the Boot Process 4-10 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Step 7 The router automaticall y boots using the default i mage (if a flash memory card containing a v alid Cisco IOS soft ware image is inse[...]

4-11 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 4 System Startup and Basic Configuration Manually Booting the System Y ou do not need to configure the netw ork interfaces immediately , bu t you cannot connect to a netw ork until you conf igure the interfaces fo r operation in your netw[...]

Chapter 4 System Sta rtup and Basic Configuration Manually Booting the System 4-12 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Locating a Valid Cisco IOS Software Image Use the follo wing procedure to locate a Cisco IOS softw are image to manually boot the router from t he ROM monitor pr ompt ([...]

4-13 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 4 System Startup and Basic Configuration Manually Booting the System Caution Use the boot flash command with care. Mak e sure that the flash memory card inserted i n slot 0 contains a valid Cisco IOS software image; otherwise, you could i[...]

Chapter 4 System Sta rtup and Basic Configuration Configuring the Router 4-14 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Note If you did not chan ge the configuratio n register setting, the ne xt reload will re vert to the defa ult configuration re gister setting (0x0102). This setting causes [...]

4-15 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 4 System Startup and Basic Configuration Cisco IOS User Interface Y ou can use the method that sui ts your operating style and your kno wledge of network co nfiguration requirement s. Whether you use the setup command facility or global c[...]

Chapter 4 System Sta rtup and Basic Configuration Cisco IOS User Interface 4-16 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 The confi guration modes allo w you to make changes to the runnin g configuration file. If you save t he configuration, the commands are sto red and persist across router [...]

4-17 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 4 System Startup and Basic Configuration Cisco IOS User Interface The follo wing example sho ws the change from user EXEC mode to pri vileged EXEC mode. Router> enable password: < passwor d > Router# For information about using p[...]

Chapter 4 System Sta rtup and Basic Configuration Cisco IOS User Interface 4-18 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Subinterface Configuration Mo de Use subinterface conf iguration mode to conf igure multiple virtual interf aces (called subinterf aces) on a single physical interf ace. S[...]

4-19 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 4 System Startup and Basic Configuration Cisco IOS User Interface T o use the setup command to change a configuration: 1. Y ou must toggle through each system conf iguration dialog promp t until you come to the item that you intend to cha[...]

Chapter 4 System Sta rtup and Basic Configuration Cisco IOS User Interface 4-20 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 to configure each interface of the system. Would you like to enter basic management setup? [yes/no]: Yes Configuring global parameters: Enter host name [Router]: Milo The [...]

4-21 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 4 System Startup and Basic Configuration Cisco IOS User Interface line vty 0 4 password bambam no snmp server ! no ip routing ! interface Ethernet0 no shutdown ip address 172.16.72.2 255.255.255.0 ! interface POS1/0 shutdown no ip address[...]

Chapter 4 System Sta rtup and Basic Configuration Cisco IOS User Interface 4-22 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 For e xample, during the conf iguration of a POS interface, (using the setup facility initial router startup), the scrip t appears as the following e xample as you respond[...]

4-23 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 4 System Startup and Basic Configuration Cisco IOS User Interface Configuring Host Name The host name you conf igure your router with must: • Follo w the rules for ARP ANET host names. • Start with a letter , end with a le tter or dig[...]

Chapter 4 System Sta rtup and Basic Configuration Cisco IOS User Interface 4-24 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 In either case, you cannot use a number as the first character . Spaces, howe ver , are v alid pas sword characters. For e xample, two words i s a valid passw ord. Leading[...]

4-25 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 4 System Startup and Basic Configuration Cisco IOS User Interface The follo wing conf iguration dialog e xample shows ho w to conf igure the system for an Ethernet interf ace that uses the IP network layer protocol. Note The Ethernet inte[...]

Chapter 4 System Sta rtup and Basic Configuration Cisco IOS User Interface 4-26 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 The follo wing example sho ws ho w to configure an A TM line card to use IP . Configuring interface parameters: Configuring interface ATM1/0: Is this interface in use?: ye[...]

4-27 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 4 System Startup and Basic Configuration Cisco IOS User Interface System image file is "tftp://xxx.xxx.xxx.xxx/directory/ghall/gsr-p-mz" cisco 12410/GRP (R5000) processor (revision 0x05) with 262144K bytes of memory. R5000 CPU a[...]

Chapter 4 System Sta rtup and Basic Configuration Cisco IOS User Interface 4-28 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Step 3 Enter the conf igure terminal comman d to enter global configuration m ode. Milo# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Mi[...]

4-29 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 4 System Startup and Basic Configuration Cisco IOS User Interface clock source internal ! interface POS1/1 no ip address no ip route-cache cef no ip route-cache shutdown crc 32 ! interface POS1/2 no ip address no ip route-cache cef no ip [...]

Chapter 4 System Sta rtup and Basic Configuration Cisco IOS User Interface 4-30 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Viewing the Running Configuration Settings Y ou can use the sho w startup-config command to view th e current configu ration settings stored in NVRAM. The follo wing examp[...]

4-31 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 4 System Startup and Basic Configuration Configuring the Software Configuration Registe r ! map-list atm1 ip 10.1.1.1 atm-vc 1 ip 10.1.1.3 atm-vc 2 ip 10.1.1.4 atm-vc 4 ip 10.0.0.1 atm-vc 3 ip 10.0.0.5 atm-vc 10 ip 10.0.0.6 atm-vc 11 no l[...]

Chapter 4 System Sta rtup and Basic Configuration Configuring the Software Configuration Reg ister 4-32 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 • Read boot system commands from the config uration file stored in NVRAM. Ta b l e 4-4 defin es software conf iguration regist er bits. Caution T[...]

4-33 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 4 System Startup and Basic Configuration Configuring the Software Configuration Registe r The boot f ield ( Ta b l e 4-5 ) defines a source for b ooting a default Cisco IOS software imag e required to run the router . The content of the b[...]

Chapter 4 System Sta rtup and Basic Configuration Configuring the Software Configuration Reg ister 4-34 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Depending on the boo t field setting, the syst em ignores boot instructions in the system conf iguration file and p erforms one of the follo wing o[...]

4-35 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 4 System Startup and Basic Configuration Configuring the Software Configuration Registe r For e xample, the filename formati on process may yield a range of typical filenames li ke the followin g: cisco2-grp . . . cisco17-grp The system u[...]

Chapter 4 System Sta rtup and Basic Configuration Configuring the Software Configuration Reg ister 4-36 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Step 3 Set the conten ts of the software conf iguration register b y entering the conf ig-register value command, where value is a hexadecimal numb[...]

4-37 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 4 System Startup and Basic Configuration Configuring the Software Configuration Registe r Low-Order Bits in the Software Configuration Register This section pro vides detail about of the lo w-order bits in the software confi guration regi[...]

Chapter 4 System Sta rtup and Basic Configuration Configuring the Software Configuration Reg ister 4-38 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Note If a bootable Cisco IOS so ftware image exists in a flash memory card installed in slot 0 or slot 1, the configuration register setting is o v[...]

4-39 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 4 System Startup and Basic Configuration Configuring the Software Configuration Registe r High-Order Bits in the Software Configuration Register This section describes the significance of high-ord er bits in the software configuration re [...]

Chapter 4 System Sta rtup and Basic Configuration Configuring the Software Configuration Reg ister 4-40 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 • Bits 11 and 12 of the softw are config uration r egister determine the data transmission rate of the console termin al. Ta b l e 4-8 shows th e[...]

4-41 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 4 System Startup and Basic Configuration Recovering a Lost Password Recovering a Lost Password Use the follo wing procedure to recov er a lost password. Note This procedure does not work fo r password recovery if the enable password is en[...]

Chapter 4 System Sta rtup and Basic Configuration Recovering a Lost Password 4-42 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 enable “use net in IP bcast address”? y/n [n]: enable “load rom after netbootfails”? y/n [n]: enable “use all zero broadcast”? y/n [n]: enable “break/abort[...]

4-43 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 4 System Startup and Basic Configuration Recovering a Lost Password Step 7 Enter the enable command and pass word (if prompted). Milo> enable Password: < password > Milo# Step 8 Enter the show st artup-config command to display t[...]

Chapter 4 System Sta rtup and Basic Configuration Using RP Flash Memory Cards 4-44 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Using RP Flash Memory Cards This section descri bes how to use RP flash memory cards and includes information on the following topics: • Installing and Remo ving a Fl[...]

4-45 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 4 System Startup and Basic Configuration Using RP Flash Memory Cards Step 3 Insert the card i nto the appropriate slot until the card completely seats i n the connector and the ejector button pops out (see Figure 4-5 b). Caution The flash[...]

Chapter 4 System Sta rtup and Basic Configuration Using RP Flash Memory Cards 4-46 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Figur e 4-5 Installing and Rem oving a Flash Memory Car d SLOT -0 SLOT -1 RESET AUX EJECT SLOT -0 SLOT -1 RESET AUX EJECT a H10703 b c SLOT -0 SLOT -1 RESET AUX EJECT[...]

4-47 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 4 System Startup and Basic Configuration Using RP Flash Memory Cards Formatting a New Flash Memory Card The flash memory card that shipped with your router contains th e default Cisco IOS software imag e you need to boot your router . If [...]

Chapter 4 System Sta rtup and Basic Configuration Using RP Flash Memory Cards 4-48 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Specifying a Cisco IOS Software Image to Boot the System Use the procedure in this section to identify a specif ic Cisco IOS software image ( new . image in this exampl[...]

4-49 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 4 System Startup and Basic Configuration Using RP Flash Memory Cards Flash Memory Commands This section describes console commands th at you can use to access the different types of flash memories. Enter these co mmands from the pri vileg[...]

Chapter 4 System Sta rtup and Basic Configuration Using RP Flash Memory Cards 4-50 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 dir Command T o list the directory conten ts of the flash memory in use, enter the dir [ device-name ] command. Where device-name can be slot0: , slot1: , or bootflash:[...]

4-51 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 4 System Startup and Basic Configuration Using RP Flash Memory Cards squeeze Command The squeeze command permanently remove s deleted files from flash memory and makes all other (u ndeleted) files cont i guous to conserve storage space. T[...]

Chapter 4 System Sta rtup and Basic Configuration Using RP Flash Memory Cards 4-52 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Booting from Flash Memory T o boot from flash mem ory , the boot f ield in the software conf iguration register (bits 3 through 0) m ust be set to a v alue between 2 an[...]

4-53 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 4 System Startup and Basic Configuration Using RP Flash Memory Cards Use the follo wing command to copy a fi le to flash memory . Milo# copy tftp: f ilename [ bootflash: | slot0: | slot1: ] filena me Where: • tftp: f ilename specifies t[...]

Chapter 4 System Sta rtup and Basic Configuration Using RP Flash Memory Cards 4-54 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CC Milo# In this example: • The exclam ation points (!!!) appear as the source f ile is being d[...]

4-55 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 4 System Startup and Basic Configuration Using RP Flash Memory Cards Use the following procedure to copy a boot able image into the flash memory card: Step 1 Boot the r outer . Step 2 Enter the enable command and pass word (if prompted). [...]

Chapter 4 System Sta rtup and Basic Configuration Using RP Flash Memory Cards 4-56 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Copying Cisco IOS Software Images Between Flash Memory Cards This procedure describes ho w to copy a later Cisco IOS softwa re image from one flash memory card to anoth[...]

4-57 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 4 System Startup and Basic Configuration Using RP Flash Memory Cards Step 3 Enter the follo wing commands to desig nate the file named image. new in the memory card in slot 0 as the ne w default system image fo r boot purposes: Milo# conf[...]

Chapter 4 System Sta rtup and Basic Configuration Using RP Flash Memory Cards 4-58 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Copying the Startup Configuration File fro m NVRAM to a Flash Memory Card Use the following procedure to copy a co nf iguration file from NVRAM to a flash memory card. [...]

4-59 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 4 System Startup and Basic Configuration Using RP Flash Memory Cards Milo# copy startup-config slot0:myfile2 20575008 bytes available on device slot0, proceed? [confirm] Address or name of remote host [1.1.1.1]? Loading new.image from 1.1[...]

Chapter 4 System Sta rtup and Basic Configuration Using RP Flash Memory Cards 4-60 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Copying the Running Configuration Fil e from DRAM to a Flash Memory Card Use the follo wing procedure to cop y the running configur ation file from DRAM on the RP to a [...]

4-61 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 4 System Startup and Basic Configuration Using RP Flash Memory Cards Step 2 Enter the dir comm and to further verify th at the configurat ion file is copied correctly to the memory card i n slot 0: Milo# dir slot0: -#- -length- -----date/[...]

Chapter 4 System Sta rtup and Basic Configuration Using RP Flash Memory Cards 4-62 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Booting a New Cisco IOS Software Image from a Flash Memory Card Use the follo wing procedure to boot a ne w image from a flash memory card in slot 0 or slot 1 (this exa[...]

4-63 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 4 System Startup and Basic Configuration Post-Installation Procedures Post-Installation Procedures After you install the router hardware, check all external connection s, turn on the system po wer , allow the system to boot up, and minima[...]

Chapter 4 System Sta rtup and Basic Configuration Post-Installation Procedures 4-64 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01[...]

CH A P T E R 5-1 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 5 Troubleshooting the Installation This chapter contains g eneral troubleshooting inform ation to help isolate the cause of dif ficulties you might encounter during the inst allation and initial start up of the system. The procedures [...]

Chapter 5 Troubleshooting the Installation Troublesho oting Over view 5-2 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Troubleshooting Overview This section descri bes the methods used in troubleshooting the ro uter . The troubleshooting methods are or ganized according to the major subsystems i[...]

5-3 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 5 Tr oubleshooting the Installation Troubleshooting Overview • Chassis backplane po wer distrib ution. –48 VDC power from t he power supplies is transfer red to the chas sis backplane. The – 48 VDC is distributed to all of the cards [...]

Chapter 5 Troubleshooting the Installation Troublesho oting Over view 5-4 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Identifying Startup Issues Ta b l e 5-1 sho ws the contents of the alphanumeric displays on th e RP and the line cards, as well as the normal LED states on the alarm card, the p[...]

5-5 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 5 Tr oubleshooting the Installation Troubleshooting the Power Subsystem Troubleshooting the Power Subsystem This section contains inf ormation to troubleshoot the po wer subsystems: • T roubleshooting the A C-Input Power Subsy stem, page[...]

Chapter 5 Troubleshooting the Installation Troublesho oting the Power Subs ystem 5-6 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Troubleshooting the AC-Input Power Subsystem A C-input po wer supplies are monitored fo r internal temperature, voltage, and current loa d by the MBus modul e on the [...]

5-7 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 5 Tr oubleshooting the Installation Troubleshooting the Power Subsystem Figur e 5-2 250 0 W AC P ower Supply Co mponents Use the follo wing procedure to troublesh oot the A C power supply if it is not operating properly after install ation[...]

Chapter 5 Troubleshooting the Installation Troublesho oting the Power Subs ystem 5-8 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Step 2 Make sure the router is powered on an d that all power cords are connected properly: • Po wer cords on the back panel of the po wer shelf are secured in plac[...]

5-9 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 5 Tr oubleshooting the Installation Troubleshooting the Power Subsystem • TEMP (flashing yello w—2500 W PEM only )—Indicates that a po wer supply fan is lock ed or malfunctioning. Note If the temp indicator is flashing , the fault in[...]

Chapter 5 Troubleshooting the Installation Troublesho oting the Power Subs ystem 5-10 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Troubleshooting the DC-Input Power Subsystem DC-input po wer supplies are monitored for i nternal temperature, voltage, and current loa d by the MBus modul e on the [...]

5-11 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 5 Tr oubleshooting the Installation Troubleshooting the Power Subsystem Figur e 5-4 240 0 W DC Po wer Supply Co mponents 1 Handle 3 Ejector le ver 2 Fan 4 Power switch 129494 PW R OK FA ULT TEMP OC PWR OK F A UL T TEMP OC 3 1 2 4[...]

Chapter 5 Troubleshooting the Installation Troublesho oting the Power Subs ystem 5-12 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Use the follo wing procedure to troubleshoo t the DC PEM if it is not operating properly af ter instal lation. Step 1 Make sure the PEM is seated properly: • Eject[...]

5-13 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 5 Tr oubleshooting the Installation Troubleshooting the Power Subsystem • TEMP (yellow)—Indicates th at the PEM is in an ov ertemperature condition causing a shut-do wn to oc cur . Note If the temp indicator is on, the f ault indicato[...]

Chapter 5 Troubleshooting the Installation Troublesho oting the Power Subs ystem 5-14 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Additional Power Subsystem Troubleshooting Information This section contains additional troubleshooting informatio n to help you isolate the cause of a po wer proble[...]

5-15 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 5 Tr oubleshooting the Installation Troubleshooting the Power Subsystem 16 3300 NA 5064 17 3308 NA 5064 18 3292 NA 5056 19 3300 NA 5072 20 3288 NA 5056 21 3296 NA 5072 22 3292 NA 5064 24 NA NA 5096 29 NA NA 4920 Slot # 48V AMP_48 (Volt) ([...]

Chapter 5 Troubleshooting the Installation Troublesho oting the Power Subs ystem 5-16 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Use the follo wing procedure to troubleshoo t the power distrib ution system. Step 1 Check each power supply to mak e sure tha t: • The ejector lev er is fully clo[...]

5-17 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 5 Tr oubleshooting the Installation Troubleshooting the Processor Subsystem Troubleshooting the Processor Subsystem The router processor subsystem consis ts of the R Ps, line cards, and alarm cards. The RPs and line cards ha ve two onboar[...]

Chapter 5 Troubleshooting the Installation Troubleshooting the Proces sor Subsystem 5-18 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Troubleshooting the RP When the router is po wered on, the alphanumeric display on the RP indi cate the follo wing ( Figure 5-5 ): • Upper ro w—Indicates whic[...]

5-19 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 5 Tr oubleshooting the Installation Troubleshooting the Processor Subsystem Troubleshooting Using the RP Alphanumeric Display Y ou can use the alphanumeri c display to isolate a problem with th e RP . The two ro w s on the alphan umeric d[...]

Chapter 5 Troubleshooting the Installation Troubleshooting the Proces sor Subsystem 5-20 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Troubleshooting Line Cards When the line card is powered on, the di splay on the line card indicates the follo wing ( Figure 5-6 ): Ta b l e 5-2 T roub leshooting[...]

5-21 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 5 Tr oubleshooting the Installation Troubleshooting the Processor Subsystem • Upper ro w—Indicates which software com ponent is running. At t he end of a successful boot process, this display reads IOS. • Lo wer row—Indicates t he[...]

Chapter 5 Troubleshooting the Installation Troubleshooting the Proces sor Subsystem 5-22 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Troubleshooting Using the Line Card Alphanumeric Display Y ou can analyze the alphanumeric displays to isolate a p roblem wi th the line c ard. The two rows of th[...]

5-23 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 5 Tr oubleshooting the Installation Troubleshooting the Processor Subsystem RST SA VE Contents of the reset reason register are being sav ed. Line card R OM monitor IO RST Reset I/O register is being accessed. Line card R OM monitor EXPT [...]

Chapter 5 Troubleshooting the Installation Troubleshooting the Proces sor Subsystem 5-24 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 IOS FA B W 3 Cisco IOS software is w aiting for the fabric to be ready . RP I OS software IOS VGE T 3 Line card is obtaining th e Cisco IOS release. RP IOS softwa[...]

5-25 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 5 Tr oubleshooting the Installation Troubleshooting the Processor Subsystem RSET DONE System reset c omplete . RP MBUS DNLD MBus agent is do wnloading. RP MBUS DONE MBus agent download complete. RP RO M I DONE Acquisiti on of R OM image c[...]

Chapter 5 Troubleshooting the Installation Troubleshooting the Proces sor Subsystem 5-26 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 DIA G MODE Diagnostic mode. RP DIA G LO AD Downloading f ield diagnostics over the MBus. RP DIA G F_LD Downloading f ield diagnostics over the f abric. RP DIA G S[...]

5-27 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 5 Tr oubleshooting the Installation Troubleshooting the Processor Subsystem Troubleshooting Using the Alarm Cards The router is eq uipped with two alar m cards: • One card occupies the dedicated far left slot of the upper card cag e. ?[...]

Chapter 5 Troubleshooting the Installation Troubleshooting the Proces sor Subsystem 5-28 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Figur e 5-7 Status LE Ds on the Alar m Car d Monitoring Critical, Major, and Minor Alarm Status The alarms can warn of an ov ertemperature condition: • On a com[...]

5-29 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 5 Tr oubleshooting the Installation Troubleshooting the Switc h Fabric Note Y ou can use the audio alarm cutoff switch to visually check that the alarm card indicators are o perating properly . If no au dible alarm is act ive , pressing t[...]

Chapter 5 Troubleshooting the Installation Troublesho oting the Switch Fabr ic 5-30 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Step 3 Enter the sho w controllers fia command for al l installed line cards and sa ve the output from each. Step 4 Proceed to the next section, Analyzing the Data . A[...]

5-31 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 5 Tr oubleshooting the Installation Troubleshooting the Switc h Fabric Router# show controllers fia Fabric configuration: Full bandwidth, redundant fabric Master Scheduler: Slot 17 Backup Scheduler: Slot 16 From Fabric FIA Errors --------[...]

Chapter 5 Troubleshooting the Installation Troublesho oting the Switch Fabr ic 5-32 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 To Fabric FIA Errors ----------------------- sca not pres 0 req error 0 uni fifo overflow 0 grant parity 0 multi req 0 uni fifo undrflow 0 cntrl parity 0 uni req 0 crc[...]

5-33 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 5 Tr oubleshooting the Installation Troubleshooting the Switc h Fabric The common failure patt erns and recommend ed actions for crc16 errors are as follo ws (one step at a time until the problem goes a way): 1. Errors indicated on more t[...]

Chapter 5 Troubleshooting the Installation Troublesho oting the Switch Fabr ic 5-34 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 -------- -------- -------- -------- -------- Los 0 0 0 0 0 state Off Off Off Off Off crc16 876 257 876 876 876 To Fabric FIA Errors ----------------------- sca not pre[...]

5-35 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 5 Tr oubleshooting the Installation Troubleshooting the Switc h Fabric Properly Seating Switch Fabric Cards The switch fabric cards in the router can be challenging to insert, and may require a small amount of force to seat correctly . If[...]

Chapter 5 Troubleshooting the Installation Troubleshooting the Cooling Subsystem 5-36 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 1 Clock Scheduler Card 3 Switch Fabric Cards 1 8-port OC3 POS controller (8 POs). 1 OC12 POS controller (1 POs). 1 OC48 POS E.D. controller (1 POs). 7 OC48 POS contr[...]

5-37 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 5 Tr oubleshooting the Installation Troubleshooting the Cooling Subsystem Figur e 5-8 Cooling Air Flow 26204 Air e xhaust Upper card cage Room air Bottom blo wer module Air filter Air e xhaust P ower supply shelf Middle card cage Lower ca[...]

Chapter 5 Troubleshooting the Installation Troubleshooting the Cooling Subsystem 5-38 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Blower Module Operation The blo wer modules maintain acceptable op e rating temperatures for the internal components by dra wing cooli ng air through a replacea ble [...]

5-39 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 5 Tr oubleshooting the Installation Troubleshooting the Cooling Subsystem Overtemperature Conditions The follo wing console error message indi ca te s that the system has detected an ov ertemperature condition or out-of-to ler ance power [...]

Chapter 5 Troubleshooting the Installation Troubleshooting the Cooling Subsystem 5-40 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Step 1 Make sur e the blower modules ar e operating properly when you po wer on the system. • T o determine if a blo wer module is operating , check the two LED in[...]

5-41 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 5 Tr oubleshooting the Installation Troubleshooting the Cooling Subsystem[...]

Chapter 5 Troubleshooting the Installation Troubleshooting the Cooling Subsystem 5-42 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01[...]

CH A P T E R 6-1 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 6 Router Field Diagnostics This chapter describes th e diagnostic commands you can use to troubleshoot l ine cards, Route Processor cards (PRP and GRP), Switch Fabric Cards (SFC), and Clock Scheduler Cards (CSC) installed i n Cisco 12[...]

Chapter 6 Router Field Diag nostics Diagnostics Overview 6-2 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 • Easy access to the most current di agnostics software—Because the field diagnostic software is no w maintained as a separat e image, the most recent version is al ways av ailable on Ci[...]

6-3 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 6 Router Field Diag nostics Field-Programmable Gate Array Ove rview Diagnostic testing stops wh en all of the te sts are completed, are terminated by the user , or by default if an error is encount ered. If mu ltiple cards are specified fo[...]

Chapter 6 Router Field Diag nostics Field-Programmab le Gate Array Overview 6-4 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Some FPGA images are b undled within the Cisco IOS image and are updated along with a ne w release. These type of FPGA images do not require flash memory storage and are d[...]

6-5 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 6 Router Field Diag nostics Field-Programmable Gate Array Ove rview Note Before updating the ne xt line card, wait about 30 seconds af ter the Cisco IOS software reloads on the line card to gi ve the router a chance to synchronize all of i[...]

Chapter 6 Router Field Diag nostics Field-Programmab le Gate Array Overview 6-6 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Step 2 Enter the diag slot- number update-fpga source { tftp | flash } sour ce-path command to update the fl ash memory . Where: • slot-number is the slot number of the [...]

6-7 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 6 Router Field Diag nostics Field-Programmable Gate Array Ove rview FD 3> Compiled by ckhuong on Fri Jan 17 15:51:36 PST 2003 FD 3> view: ckhuong-conn_isp.inti4 FD 3> ***************************************************** Diagnosti[...]

Chapter 6 Router Field Diag nostics Using the diag Comm and 6-8 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Using the diag Command Y ou can use the diag command to run field diag nostics on a line card, Route Processor card (PRP and GRP), Switch Fabri c Card (SFC), or Clock and Scheduler Card ([...]

6-9 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 6 Router Field Diag nostics Using the diag Command Diagnostic Commands for Cisco 12000 Series Rout Processors The follo wing diagnostic commands apply to GRP and P RP route processors. diag slot-number [ verbose ] [ wait ] [ full ] [ coe ][...]

Chapter 6 Router Field Diag nostics Using the diag Comm and 6-10 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 sour ce-path Specifies the path to the diagnostic image f ile c12k-fdiagsbflc-mz. IOS Release Where IOS Release corresponds to the Cisco IOS release number . For e xample: c12k-fdiagsbfl[...]

6-11 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 6 Router Field Diag nostics Using the diag Command verb ose (Optional) Enables progress and error messages to be displayed on the co nsole. By default, onl y the minimum status messages appear on the console, along with th e final result.[...]

Chapter 6 Router Field Diag nostics Using the diag Comm and 6-12 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 After all diagnostic tests are completed on a line card , a P ASSED or TEST F AILURE message appears on the console. • If the line card passes, the Cisco IOS software image on the line[...]

6-13 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 6 Router Field Diag nostics diag Command O utput Examples Caution Do not replace memory components with out properly grounding both the board and yourself. diag Command Output Examples This section contains output examples using diag co m[...]

Chapter 6 Router Field Diag nostics diag Command Output E xamples 6-14 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 FD 7> ***************************************************** FD 7> GSR Field Diagnostics V6.05 FD 7> Compiled by award on Tue Jul 30 13:00:41 PDT 2002 FD 7> view: award-[...]

6-15 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 6 Router Field Diag nostics diag Command O utput Examples Loading images/award/c12k-fdiagsbflc-mz from 192.164.1.1 (via Ethernet0): !!!!!! (...) 00:08:24: Downloading diags from tftp file tftp:// 192.164.1.1/images /award/c12k-fdiagsbflc-[...]

Chapter 6 Router Field Diag nostics diag Command Output E xamples 6-16 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 FDIAG_STAT_IN_PROGRESS(7): test #25 TBM to RX SOP Packet - 4302 Terminal Loopback FDIAG_STAT_IN_PROGRESS(7): test #26 TBM to RX SOP Packet - Framer System Bus Loop FDIAG_STAT_IN_PR[...]

CH A P T E R 7-1 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 7 Maintaining the Router Y our router is equipped as ordered and is ready for installatio n and startup when it is shipped. As your netw orking requirements change, you may need to upgrade the system by add ing or changing components.[...]

Chapter 7 M aintaining the Router Powering Off the Router 7-2 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 • Removing and Replacin g Cards from the Chassis, page 7-79 • Upgrading the Switch F abric, page 7-86 • Removing and I nstalling a Chassis, page 7-88 • Removing and Replacin g a Pow[...]

7-3 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 7 Maintaining the Router Removing and Installing the Front Covers and Beze l Extenders o n Original Cisco 12000 Series Routers Step 3 V erify that the PWR OK indicator on each po wer supply is of f. Step 4 V erify that the OK indicator on [...]

Chapter 7 M aintaining the Router Removing and Installi ng the Front Covers and Beze l Extenders on Original Cisco 12000 Series Routers 7-4 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Installing the Front Covers Refer to Figure 7-1 and use the following proced ur e to install the front covers. [...]

7-5 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 7 Maintaining the Router Removing and Installing the Front Covers and Beze l Extenders o n Original Cisco 12000 Series Routers Figur e 7 -1 Router Chassis F ront Co vers 1 Ball stud 2 Ball stud clip P W R O K F A U L T T E M P I L I M P W [...]

Chapter 7 M aintaining the Router Removing and Installi ng the Front Covers and Beze l Extenders on Original Cisco 12000 Series Routers 7-6 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Attaching Bezel Extenders to the Front Cover Use the follo wing proced ure to attach the beze l extenders to t [...]

7-7 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 7 Maintaining the Router Removing and Installing the Front Covers and Beze l Extenders o n Original Cisco 12000 Series Routers Figur e 7- 2 Attac hing the Bezel Extenders t o a Card Cag e Fr ont Cov er Step 5 Hold the card cage front cov e[...]

Chapter 7 M aintaining the Router Removing and Installi ng the Front Covers and Beze l Extenders on Original Cisco 12000 Series Routers 7-8 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Figur e 7 -3 Attac hing the F ront Co vers Using Bezel Exte nders 1 Ball stud 2 Ball stud clip P W R O K F A U [...]

7-9 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 7 Maintaining the Router Removing and Installing the Front Covers and Beze l Extenders o n Original Cisco 12000 Series Routers Step 6 Push the front co ver into the ball stud clips so that the front co ver is flush with the front of the ch[...]

Chapter 7 M aintaining the Router Removing and Installi ng the Front Covers and Beze l Extenders on Original Cisco 12000 Series Routers 7-10 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Figur e 7 -4 Opening the Chas sis Air Filter Doo r Caution Be especially careful not to damage the honeycomb s[...]

7-11 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 7 Maintaining the Router Removing and Installing the Front Covers and Beze l Extenders o n Original Cisco 12000 Series Routers Step 2 Remov e the (4) scre ws from each corner that fasten the partial front cover to the air filter door ( Fi[...]

Chapter 7 M aintaining the Router Removing and Installi ng the Front Covers and Beze l Extenders on Original Cisco 12000 Series Routers 7-12 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Step 4 Secure the front co ver to the air f ilter door using the (4) screws that you remove d in Step 2. Cauti[...]

7-13 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 7 Maintaining the Router Removing and Installing Front Doors o n Cisco 12016 Enhanced Series Routers Removing and Installing Front Doors on Cisco 12016 Enhanced Series Routers The Cisco 12016 enhanced series routers ha ve ne w front doors[...]

Chapter 7 M aintaining the Router Removing and Installing Front Doors on Cisco 1 2016 Enhanced Series Routers 7-14 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Step 1 Open the top fron t door by pressing the righ t latch button ( Figure 7-7 ). Figur e 7 -7 Opening the F ront Door 1 Front door la[...]

7-15 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 7 Maintaining the Router Removing and Installing Front Doors o n Cisco 12016 Enhanced Series Routers Step 2 Remov e the front door b y lifting the (top and bottom) hinge pins to free the door from the chassis ( Fig ure 7-8 ). Caution Make[...]

Chapter 7 M aintaining the Router Removing and Installing Front Doors on Cisco 1 2016 Enhanced Series Routers 7-16 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Step 3 Remov e the bu mpers and piv ot blocks from the door as sho wn in Figure 7-9 . Figur e 7 -9 Removing the Bumpers and Piv ot Block[...]

7-17 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 7 Maintaining the Router Cleaning or Replacing the Chassis Air Filter Step 4 Reinstall the hardw are to the opposite sides of the front door: a. Mount pi vot blocks to t he left side and tighten the scre ws until snug. b. Mount the b umpe[...]

Chapter 7 M aintaining the Router Cleaning or Replacing the Chassis Air Filter 7-18 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Cleaning or Replacing the Chassis Air Filter on Cisco 12016 Original Series Routers Use the follo wing procedure to clean or replace an original series air f ilter . S[...]

7-19 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 7 Maintaining the Router Cleaning or Replacing the Chassis Air Filter Step 2 Lift up the air f ilter and c a refully slide it out th e door ( Figure 7-11 ). Caution Be careful not to damage the hone ycomb screens on the back of the air fi[...]

Chapter 7 M aintaining the Router Cleaning or Replacing the Chassis Air Filter 7-20 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Step 3 V isually check the condition of the air filter to deter mine whether to clean it or install a new replacement. • Dirty—Y ou can v a cuum or replace the fil[...]

7-21 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 7 Maintaining the Router Cleaning or Replacing the Chassis Air Filter Step 5 Lift up the air f ilter door so that th e four guide pins are inserted in the corresponding holes on each side of the switch fabric card cage ( Fi gure 7-13 ). C[...]

Chapter 7 M aintaining the Router Cleaning or Replacing the Chassis Air Filter 7-22 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Cleaning or Replacing the Chassis Air Filter on Cisco 12016 Enhanced Series Routers Use the follo wing procedure to clean or replace th e enhanced series air f ilter .[...]

7-23 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 7 Maintaining the Router Cleaning or Replacing the Chassis Air Filter Step 2 Lift up the air f ilter and c arefu lly slide it out of the door ( Figure 7-11 ). Caution Be careful not to damage the hone ycomb screens on the back of the air [...]

Chapter 7 M aintaining the Router Removing and Replacing Blower Module s 7-24 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Step 3 V isually check the condition of the air filter to deter mine whether to clean it or install a new replacement. • Dirty—Y ou can v a cuum or replace the filter . [...]

7-25 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 7 Maintaining the Router Removing and Replacin g Blower Modules If you are r eplacing an: • Original blo wer module (GSR16-B LOWER=)—Use an original blo wer module or enhanced capacity blo wer module s as replacements. • Enhanced ca[...]

Chapter 7 M aintaining the Router Removing and Replacing Blower Module s 7-26 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 • Heads-do wn orientation—Install the blo wer module in the lo wer blower module bay in the “heads-do wn” orientatio n with the three fan air intak e openings face u[...]

7-27 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 7 Maintaining the Router Removing and Replacin g Blower Modules Step 2 Install the ne w blower module into the chassis ( Figure 7-17 ): a. Lift the blo wer module (with two hand s) and slide it halfway into the module bay . b. Slo wly pus[...]

Chapter 7 M aintaining the Router Removing and Replacing Blower Module s 7-28 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Troubleshooting the Blower Installation Use the follo wing procedure to troubleshoot a blo wer module if it is not operating properly af ter instal lation. Step 1 Be sure th[...]

7-29 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 7 Maintaining the Router Removing and Replacing AC and DC Power Subsystem Components Removing and Replacing AC and DC Power Subsystem Components This section contains remov al and repl acement procedures for the A C and DC po wer systems [...]

Chapter 7 M aintaining the Router Removing and Replac ing AC and DC Power Subsystem Components 7-30 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Power Supply and Power Shelf Compatibility Cisco 12016 series routers are av ailable with either an A C or a DC power supply system. T wo types of powe[...]

7-31 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 7 Maintaining the Router Removing and Replacing AC and DC Power Subsystem Components AC Power Supply (PWR-GSR16-AC=) Use to replace original 2000 W AC po wer supplies only . All po wer supplies in the power shelf must be 2000 W . Do not m[...]

Chapter 7 M aintaining the Router Removing and Replac ing AC and DC Power Subsystem Components 7-32 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Installing Upgrade Kits When installing a power system upgr ade kit, you replace the following components: • A C power up grades (12000/16-A C-UP=, 1[...]

7-33 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 7 Maintaining the Router Removing and Repla cing an AC Po wer Supply Removing and Replacing an AC Power Supply This section pro vides the procedure to remov e an A C power supply fro m the standard single-le vel A C power shelf. The pr oc[...]

Chapter 7 M aintaining the Router Removing and Replacing an AC Power Supp ly 7-34 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Figure 7-19 identif ies the components of a 2000 W A C po wer supply . Figur e 7 -19 200 0 W AC P ower Supply Components Handle Ejector le ver 26200 PW R O K FAU LT TE M[...]

7-35 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 7 Maintaining the Router Removing and Repla cing an AC Po wer Supply Figure 7-20 identif ies the components of a 2500 W A C po wer supply . Figur e 7 -20 250 0 W AC P ow er Supply Co mp onents 1 Ejector handle 2 Capti ve scr ew 129495 Pwr[...]

Chapter 7 M aintaining the Router Removing and Replacing an AC Power Supp ly 7-36 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 T o remove and replace an A C power supply , use the following procedure. Caution Y ou cannot mix power supply types within the chassis. If you plan to replace a 2000 W [...]

7-37 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 7 Maintaining the Router Removing and Repla cing an AC Po wer Supply Step 4 Remove the 2000 W PEM ( Figure 7-21 ): a. Release the ejector lever b y lifting the spring clip. b. Pi vot the le ver do wn to eject the po wer supply from its ba[...]

Chapter 7 M aintaining the Router Removing and Replacing an AC Power Supp ly 7-38 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Step 5 Remove the 2500W PEM ( Figure 7-22 ): a. Loosen the captiv e screw to release the ejector handle. b. Pi vot the ejector handle do wn to eject the po wer supply fr[...]

7-39 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 7 Maintaining the Router Removing and Repla cing an AC Po wer Supply Step 7 Install the 2000W PEM ( Figure 7-23 ): a. Slide the po wer supply into the bay until it mates with its backplane connector . Caution T o pre vent damage to the po[...]

Chapter 7 M aintaining the Router Removing and Replacing an AC Power Supp ly 7-40 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Figur e 7 -23 Installing a 20 00 W AC P ow er Supply PW R O K FAULT TEMP I LIM P WR OK FAULT TEMP I LIM PW R OK F AULT TEMP I LIM 26869[...]

7-41 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 7 Maintaining the Router Removing and Repla cing an AC Po wer Supply Step 8 Install the 2500 W po wer supply ( Figure 7-24 ): a. Slide the po wer supply into the bay until it mates with its backplane connector . Caution T o pre vent damag[...]

Chapter 7 M aintaining the Router Removing and Replacing an AC Power Supp ly 7-42 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Troubleshooting the AC Power Supply Installation Use the follo wing procedure to troublesh oot the A C power supply if it is not operating properly after install ation. [...]

7-43 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 7 Maintaining the Router Removing and Repla cing an AC Po wer Supply • TEMP (yellow)—Indicates that the po we r supply is in an ov ertemperature condition, ca using a shut -down to occur . Note If the temp indicator is on, the f ault [...]

Chapter 7 M aintaining the Router Removing and Replacing the Standard AC- Input Power Shelf 7-44 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 • OC (2500 W PEM only) (steady , or flashing yellow after 10 seconds)—Indicat es the output current of t he power supply has e xceeded its limit and t[...]

7-45 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 7 Maintaining the Router Removing and Replacing the St andard AC-Inp ut Power Shelf Step 2 Disconnect each of the A C power cords fr om the back panel o f the power shelf b y lifting the retention clip and unplugging the cord ( Figure 7-2[...]

Chapter 7 M aintaining the Router Removing and Replacing the Standard AC- Input Power Shelf 7-46 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Step 3 Unseat the po wer shelf from the chassis ( Figure 7-26 ): a. Loosen the two captiv e screws on each side of the po wer shelf. b. Loosen the eje cto[...]

7-47 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 7 Maintaining the Router Removing and Replacing the St andard AC-Inp ut Power Shelf Step 4 Remov e the po wer shelf by grasping the flan ges on each side and slowly pul ling the shelf along the chassis track to remove it ( Figure 7-27 ): [...]

Chapter 7 M aintaining the Router Removing and Replacing the Standard AC- Input Power Shelf 7-48 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Step 5 Insert the new po wer shelf halfway into the chassis. Step 6 Connect the po wer she lf to the chassi s po wer interface panel connectors ( Figure 7[...]

7-49 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 7 Maintaining the Router Removing and Replacing the St andard AC-Inp ut Power Shelf Step 7 Seat the power shelf to the chassis ( Figure 7-29 ): a. T ighten the ejector jackscrew . b. T ighten the captive scre ws on each flange. Figur e 7 [...]

Chapter 7 M aintaining the Router Removing and Replacing the Standard AC- Input Power Shelf 7-50 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Step 8 Reconnect each of the A C power cords to the back panel of the po wer shelf and secure them in place with their re tention clips ( Figure 7-30 ). F[...]

7-51 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 7 Maintaining the Router Removing and Replacing the Optional 2-Level AC-Inp ut Power Shelf Removing and Replacing the Optional 2-Level AC-Input Power Shelf Use the following procedure to remo ve and replace the optional 2-lev el A C-input[...]

Chapter 7 M aintaining the Router Removing and Replacing the Optional 2-Le vel AC-Input Power Shelf 7-52 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Step 2 Disconnect each of the A C power cords fr om the back panel o f the power shelf b y lifting the retention clip and unplugging the cord ( Fi[...]

7-53 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 7 Maintaining the Router Removing and Replacing the Optional 2-Level AC-Inp ut Power Shelf Step 3 Loosen the two capti ve screws on each side of the po wer shelf. Step 4 Loosen the ejector jackscrew to unseat th e po wer shelf from the co[...]

Chapter 7 M aintaining the Router Removing and Replacing the Optional 2-Le vel AC-Input Power Shelf 7-54 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Step 6 Insert the new po wer shelf halfway into the chassis. Step 7 Connect the po wer she lf to the chassi s po wer interface panel connectors ( [...]

7-55 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 7 Maintaining the Router Removing and Replacing the Optional 2-Level AC-Inp ut Power Shelf Step 8 Install the po wer shelf by grasping the flanges on each side and slo wly sliding the shelf into the chassi s alon g the track ( Figure 7-34[...]

Chapter 7 M aintaining the Router Removing and Replacing the Optional 2-Le vel AC-Input Power Shelf 7-56 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Step 9 Reconnect each of the A C power cords to the back panel of the po wer shelf and secure them in place with their re tention clips ( Figure 7[...]

7-57 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 7 Maintaining the Router Removing and Replacing the Optional 2-Level AC-Inp ut Power Shelf Troubleshooting the AC Power Shelf Installation Use the follo wing procedure to troublesh oot the A C power shelf if i t does not operate properly [...]

Chapter 7 M aintaining the Router Removing and Replacing the Optional 2-Le vel AC-Input Power Shelf 7-58 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 • TEMP (yellow)—Indicates that the po we r supply is in an ov ertemperature condition, ca using a shut -down to occur . Note If the temp indic[...]

7-59 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 7 Maintaining the Router Upgrading the AC-Input Power Shelf • OC (2500 W PEM only) (steady , or flashing yellow after 10 seconds)—Indicat es the output current of the power supply e xceeded its limit and an overload or short circuit h[...]

Chapter 7 M aintaining the Router Removing and Replacing a DC PEM 7-60 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Removing and Replacing a DC PEM This section contains the procedure to remove and replace an DC PEM from the chassis. Befor e you begi n this procedure, read the “Installation Gu[...]

7-61 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 7 Maintaining the Router Removing and Replacing a DC PEM Figure 7-37 identif ies the components of a 2400 W DC po wer supply . Figur e 7 -37 240 0 W DC P ower Supply Co mponents Caution Y ou cannot mix power supply types within the chassi[...]

Chapter 7 M aintaining the Router Removing and Replacing a DC PEM 7-62 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Use the following procedure to remo ve and replace a DC PEM. Step 1 Po wer off the P EM by switching its circuit breake r off. Step 2 Po wer off the DC circuit breaker assigned to [...]

7-63 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 7 Maintaining the Router Removing and Replacing a DC PEM Figur e 7 -38 Removing a DC PEM P W R O K F AU LT TEM P PW R OK F AU LT TE M P P W R O K FAU LT T E M P PW R O K FA UL T TE M P 26212 Loosen captive screw a Pivot ejector le ver b P[...]

Chapter 7 M aintaining the Router Removing and Replacing a DC PEM 7-64 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Step 5 Install the ne w DC PEM into the po wer shelf ( Figure 7-39 ): a. Slide the PEM halfw ay into the chassis. b. Slo wly push the power supply int o the chassis until it mates [...]

7-65 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 7 Maintaining the Router Removing and Replacing a DC PEM Figur e 7 -39 Installing a DC PEM Step 6 Po wer on the DC circuit breaker assig ned to that PEM. Step 7 Po wer on the PEM by switching o n its circuit breaker . After the po wer-on [...]

Chapter 7 M aintaining the Router Removing and Replacing a DC PEM 7-66 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Troubleshooting the DC PEM Installation Use the follo wing procedure to troubleshoo t the DC PEM if it is not operating properly af ter instal lation. Step 1 Make sure the PEM is s[...]

7-67 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 7 Maintaining the Router Removing and Replacing a DC PEM • TEMP (yellow)—Indicates th at the PEM is in an ov ertemperature condition causing a shut-do wn to oc cur . Note If the temp indicator is on, the f ault indicator also goes on.[...]

Chapter 7 M aintaining the Router Removing and Replacing the DC-Input Power Shelf 7-68 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Removing and Replacing the DC-Input Power Shelf Use the follo wing procedure to remov e and replace the DC-input power shelf. Caution T o remov e and replace the po[...]

7-69 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 7 Maintaining the Router Removing and Replacing the DC-Input Power Shelf Step 3 Measure the voltag e across each pair of positi ve (+) and negati ve (–) t erminals of the power shelf to be sure they are not receiving power . • All rea[...]

Chapter 7 M aintaining the Router Removing and Replacing the DC-Input Power Shelf 7-70 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Figur e 7- 41 Disconnecting the Sour ce DC Po wer Cables 28018 Ground – + A1- A1+ A2- A2+ B2+ B2- B1+ B1- Ground B1 Negative (–) cable lug P ositive (+) cable l[...]

7-71 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 7 Maintaining the Router Removing and Replacing the DC-Input Power Shelf Step 5 Unseat the po wer shelf from the chassis ( Figure 7-42 ): a. Loosen the two captiv e screws on each side of the po wer shelf. b. Loosen the ejector jackscrew [...]

Chapter 7 M aintaining the Router Removing and Replacing the DC-Input Power Shelf 7-72 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Step 6 Remov e the po wer shelf by grasping the flan ges on each side and slowly pul ling the shelf along the chassis track to remove it ( Figure 7-43 ): Figur e 7 [...]

7-73 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 7 Maintaining the Router Removing and Replacing the DC-Input Power Shelf Step 7 Insert the new po wer shelf halfway into the chassis. Step 8 Connect the po wer she lf to the chassi s po wer interface panel connectors ( Figure 7-44 ): a. B[...]

Chapter 7 M aintaining the Router Removing and Replacing the DC-Input Power Shelf 7-74 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Step 9 Seat the power shelf to the chassis ( Figure 7-45 ): a. T ighten the ejector jackscrew . b. T ighten the captive scre ws on each flange. War ni n g The DC-in[...]

7-75 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 7 Maintaining the Router Removing and Replacing the DC-Input Power Shelf War ni n g When reconnecting source DC power cables, alway s connect the ground cable first. a. Reconnect the ground cabl e to the ground terminal studs. Beginning w[...]

Chapter 7 M aintaining the Router Removing and Replacing the DC-Input Power Shelf 7-76 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Step 11 Power on the source DC circuit breakers for t he PEMs. Step 12 V erify the polarity and volt age readings across the pairs of positiv e and negati ve termin[...]

7-77 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 7 Maintaining the Router Removing and Replacing the DC-Input Power Shelf Troubleshooting the DC Power Shelf Installation Use the follo wing procedure to troublesh oot the DC power shelf if it is not operating properly after install ation.[...]

Chapter 7 M aintaining the Router Removing and Replacing the DC-Input Power Shelf 7-78 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Step 4 Check the po wer supply status indicato rs: • PWR OK (green)—Indicates that the PEM is operating normally , and the source DC v oltage is within the nomi[...]

7-79 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 7 Maintaining the Router Removing and Replacing Cards from the Chassis • OC (2400 W PEM only) (steady , or flashing yellow after 10 seconds)—Indicat es the output current of the power supply e xceeded its limit and an overload or shor[...]

Chapter 7 M aintaining the Router Removing and Replac ing Cards from the Chassis 7-80 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Caution Handle all cards b y the metal card carrier ed ges only; av oid touching the board or any connector p ins. After removing a card, carefully place it in an an[...]

7-81 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 7 Maintaining the Router Removing and Replacing Cards from the Chassis Figur e 7- 48 Removing a Line Car d from th e Line Card and RP Car d Cage Removing and Replacing an Alarm Card The router is equipped with two alarm card s. One card o[...]

Chapter 7 M aintaining the Router Removing and Replac ing Cards from the Chassis 7-82 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Figur e 7 -49 Alar m Card Locations in th e Upper and Low er Card Cages ALARM ENABLED FAIL ACO/LT ALARM CSC 0 FAIL 1 0 1 2 ENABLED CRITICAL MAJOR MINOR SFC A C T I V[...]

7-83 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 7 Maintaining the Router Removing and Replacing Cards from the Chassis Use the following procedure to remo ve an d replace an alarm card from either the top or bottom card cage. Caution T o ensure proper alarm card screw alignmen t, line [...]

Chapter 7 M aintaining the Router Removing and Replac ing Cards from the Chassis 7-84 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Removing and Replacing Switch Fabric Cards The switch fabric card cage is located be hind the air filter doo r on the front of the chassis. The card cage has fi ve k[...]

7-85 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 7 Maintaining the Router Removing and Replacing Cards from the Chassis Step 2 Re move t he ca r d: a. Pi vot the ejector le vers to unseat th e card from the backplane connector . b. Grasp the card by its metal card carrier and slide the [...]

Chapter 7 M aintaining the Router Upgrading the Swit ch Fabric 7-86 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Upgrading the Switch Fabric The switch fabri c on the Cisco 12016 and the Cisco 1241 6 routers can be upgraded in the f ield. • Cisco 12016 Routers can b e upgraded from a 2.5 Gbps [...]

7-87 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 7 Maintaining the Router Upgrading the Switch Fabric Upgrade Procedures T o upgrade the switch fa bric, follow these steps: Step 1 Po wer off the r outer . Step 2 Remov e all CSCs and SFCs from the sw itch fabric card cage. See the “Rem[...]

Chapter 7 M aintaining the Router Removing and Installing a Chassis 7-88 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Step 11 Run the show gsr command to v erify that the ne w switch fabric cards are dete cted by the system. Note The show gsr command output varies sl ightly between each switch f[...]

7-89 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 7 Maintaining the Router Removing and Installing a Chassis Because you are removing all the compon ents (except the air f ilter) from the defectiv e chassis and then rein stalling t hem in the replacement chass is, the procedures that fol[...]

Chapter 7 M aintaining the Router Removing and Installing a Chassis 7-90 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Preparing the Replacement Chassis Before you can be gin to install components in the replacement chassis, yo u need to temporarily connect the central of fice groundi ng system o[...]

7-91 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 7 Maintaining the Router Removing and Installing a Chassis Step 6 Disconnect the cables from each alarm card. Label each of the alarm card cables before you disconnect them. Step 7 Disconnect the line card interface cables: a. Identify th[...]

Chapter 7 M aintaining the Router Removing and Installing a Chassis 7-92 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Removing the Chassis from the Equipment Rack Use the follo wing procedure to remov e the chassis from the equipment rack . War ni n g T wo people are required to remove the chass[...]

7-93 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 7 Maintaining the Router Removing and Installing a Chassis Step 4 W orking from the t op of the chassis do wn, remove the scre ws that secure the chassis to the mounting flanges on the rack ( Figure 7-54 ). • Set the screws aside fo r u[...]

Chapter 7 M aintaining the Router Removing and Installing a Chassis 7-94 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Figur e 7 -54 Removing t he Mounting Scr ews 26864 Chassis mounting holes group E Chassis mounting holes group D Chassis mounting holes group C Chassis mounting holes group B Cha[...]

7-95 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 7 Maintaining the Router Removing and Installing a Chassis Step 5 Position o ne person in front of the chassis to support and guide it while the second person slowly pushes the ch assis to slide it off the r ack-mounting table and on to t[...]

Chapter 7 M aintaining the Router Removing and Installing a Chassis 7-96 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Step 7 T urn the scissor -jack screw clockwise to sl owly lo wer the scissor-jack platform ( Figure 7-56 ). Figur e 7- 56 Closing the Scissor -Jac k Pl at form to L owe r t h e C[...]

7-97 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 7 Maintaining the Router Removing and Replacing a Power Bus Board Fu se Installing the Replacement Chassis Use the follo wing procedure to instal l the replacement rack in the chassis. Step 1 Disconnect the t emporary ground conn ections [...]

Chapter 7 M aintaining the Router Removing and Replacing a Power Bus Board Fuse 7-98 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Use the following procedure to replace a fuse on the po wer bus board. Step 1 Po wer off the rout er (see Powering Of f the Router , page 7-2 ). War ni n g The router[...]

7-99 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Chapter 7 Maintaining the Router Removing and Replacing a Power Bus Board Fu se Figur e 7 -58 Removing and Replacing a P ow er Bus Board F use F2 F1 - MBus F2 - 5.1V bias Fuse is 2A/125V MBus module F1 Fuse Fuse pulling tool Fuse holder 28449 Scr[...]

Chapter 7 M aintaining the Router Removing and Replacing a Power Bus Board Fuse 7-100 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01[...]

A-1 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 APPENDIX A Technical Specifications This appendix inclu des the following sectio ns: • Router Specifi cations, page A-1 • Compliance and Safety Information, page A-5 Router Specifications The Cisco 12016, Cisco 12416, and Cisco 1 2816 Router o[...]

Appendix A Technical Sp ecifications Router Specifications A-2 Cisco 12016, Cisco 12416, and Cisco 12816 Router Installation and Configuration Guide OL-11495-01 Ta b l e A -1 Ph ysical Specifications fo r Cisco 1200 0 Ser ies Routers Description Va l u e Chassis he ight • W ith standard A C-input po wer shelf or DC-input po wer shelf • W ith op[...]

A-3 Cisco 12016, Cisco 12416, and Ci sco 12816 Router Install ation and Configuration Guide OL-11495-01 Appendix A Technical Sp ecifications Router Specifications Caution T o ensure that th e chassis configuration compli es with the required po wer budgets, use the on-line po wer calcula tor . Failure to properly v erify the confi guration may resu[...]

Appendix A Technical Sp ecifications Router Specifications A-4 Cisco 12016, Cisco 12416, and Cisco 12816 Router Installation and Configuration Guide OL-11495-01 Input current rating 60A maximum @ 40.5 VDC Source DC service requirement Suf fi cient to supply the rated input current. Local codes apply . 1. For each PEM. Caution T o ensure that th e c[...]

A-5 Cisco 12016, Cisco 12416, and Ci sco 12816 Router Install ation and Configuration Guide OL-11495-01 Appendix A Technical Sp ecifications Compliance and Safety Info rmation Compliance and Safety Information The Cisco 12016, Cisco 2416 and Ci sco 12816 routers are desi gned to meet the regul atory compliance and sa fety ap prov al requirements. R[...]

Appendix A Technical Sp ecifications Compliance an d Sa fety Information A-6 Cisco 12016, Cisco 12416, and Cisco 12816 Router Installation and Configuration Guide OL-11495-01[...]

B-1 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 APPENDIX B Site Log The site log pro vides a historical record of all actions rel ev ant to the operation and maintenance of the router . Keep y our site log in a con venient place near the router where anyone wh o performs the main tenance ha s a[...]

Appendix B Site Log B-2 Cisco 12016, Cisco 12416, and Cisco 12816 Router Installation and Configuration Guide OL-11495-01 Date Action Performed or Symptoms Observed Initials[...]

B-3 Cisco 12016, Cisco 12416, and Ci sco 12816 Router Install ation and Configuration Guide OL-11495-01 Appendix B Site Log[...]

Appendix B Site Log B-4 Cisco 12016, Cisco 12416, and Cisco 12816 Router Installation and Configuration Guide OL-11495-01[...]

IN-1 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 INDEX Numerics 100BASE-T maximum cable lengths 2-35, 2-44 specifications 2-35, 2-44 transmission specifications 2-35, 2-44 100BASE-TX 2-29 connections 3-38 10BASE-T connections 3-38 ports 2-36, 3-31, 3-36 16-bit register 4-31 25-pin D-subcon nect[...]

Index IN-2 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 asynchronous serial ports See aux iliary port Asynchronous Transfer Mode, interface configuration 4-26 attaching cables auxiliary and console port 3-36 autosensing 2-40, 3-38 auxiliary port connecting devices to 2-38, 3-33, 3-38 connector p[...]

IN-3 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Index attaching GRP Ethernet port 3-33 to 3-35 console port 2-39 DC-input power 2-19 DC-input power cable lug 2-20 interference 2-24 polarity, DC-input power sh elf 2-20 cables, attaching auxiliary and console port 3-31 bonding and grou nding cab[...]

Index IN-4 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 Cisco 12416 and 12816 r outer insertion height 3-16 Cisco Express Forwarding (CEF) 2-40 clearances, air circulation 1-45 clips, bend radius 3-27 clock, system 1-20 clock and scheduler card 1-20 commands boot 4-13, 4-34, 4-37 boot bootflash [...]

IN-5 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Index system 4-14 to 4-28 using con figura tion mode 4-27 to 4-28 configuring flash memory 4-44 connecting alarm card cable 2-45 auxiliary port 3-33 console port 3-32 connection guidelines, GRP 2-26 to 2-35 connection guidelines, PRP 2-37 to 2-44[...]

Index IN-6 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 shelf specifications A-3 DC-input power entry mo dule removing 7-63 DC-input power shelf terminal connector locations 3-44 DC-to-DC converters 5-22 default bo ot filename s 4-38 delete com mand 4-50 dir command 4-50 DRAM GRP attribute summa[...]

IN-7 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Index F Fast Ethernet specifications 2-44 figures alarm card connector location 3-40 status LEDs 5-28 bonding and grou nding cable receptacle locations 2-23, 3-23, 3-24 GRP RJ-45 and MII Ethern et connectio ns 3-34 filenames, for booting over net[...]

Index IN-8 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 RJ-45 and MII Ethern et connectio ns (figure) 3-34 RJ-45 Ethernet connection 2-29 RJ-45 Ethernet Rece ptacle and m odular plug 2-31 soft reset switch function 1-27, 1-37 usage (caution) 1-27, 1-37 SRAM 1-33 GRP board U39 1-31 GSR rack-mount[...]

IN-9 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Index OK (green) 4-4 PWR OK 4-4 route processor 5-19, 5-20, 5-22 line card alphanumeric LED disp lays 4-8, 5-21 attaching i nte rface ca bles 3-27 LED sequences 4-8 network interface cable connec tion 3-28 RP card cage 1-2 line card and RP card c[...]

Index IN-10 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 OEM bit 4-32 P Packet-over-SONET, interface configuration 4-25 parameters 4-22 part numb ers 1-42 passwords noting 4-24 recovering 4-43 valid 4-24 PCMCIA slot 1-35 slot descriptio n 1-25 physical specification s A-2 pinouts alarm card conn[...]

IN-11 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Index R rack insertion 3-18 rack-mounting guidelin es 2-11 platform installati on 3-14 verifying rack dimensions 3-8 radio frequency interference See RFI prevention raising router 3-16 recovering a lost password 4-41 reload command 4-36 removing[...]

Index IN-12 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01 site require ments air flow 2-15 power 2-20 rack mounting 2-7, 2-11 site log B-1 supplemental earth g round connection 2-22 temperature and h umidity 2-17 soft reset (NMI) switch (caution) 1-27, 1-37, 5-19 software configurat ion register [...]

IN-13 Cisco 12016, Cisco 12416, and Cisco 12816 R outer Installation and Configuration Guide OL-11495-01 Index sensors 1-46 system specifications A-4 terminal connector locations DC-input power shelf 3-44 TFTP requests 4-34 TFTP server 4-33, 4-40 Token Ring 2-36, 3-31, 3-36 transceiver 3-35 transmission recommendation s 100BASE-T 2-44 Trivial File [...]

Index IN-14 Cisco 12016, Cisco 12416, and Cisco 1281 6 Router Installation and Configuration Guide OL-11495-01[...]